ETSI standard defines "Offchannel CAC" as:
"Off-Channel CAC is performed by a number of non-continuous checks
spread over a period in time. This period, which is required to
determine the presence of radar signals, is defined as the Off-Channel
CAC Time..
Minimum Off-Channel CAC Time 6 minutes and Maximum Off-Channel CAC Time
4 hours..".
mac80211 implementation refers to a dedicated hw chain used for continuous
radar monitoring. Rename offchannel_* references to background_* in
order to avoid confusion with ETSI standard.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Link: https://lore.kernel.org/r/4204cc1d648d76b44557981713231e030a3bd991.1638190762.git.lorenzo@kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Introduce a disconnect function that can be used when a
channel switch error occurs. The channel switch can request to
block the tx, and so, we need to make sure we do not send a deauth
frame in this case.
Signed-off-by: Nathan Errera <nathan.errera@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20211129152938.cd2a615a0702.I9edb14785586344af17644b610ab5be109dcef00@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When color change is triggered in multiple bssid case, allow
only for transmitting BSS, and when it changes its bss color,
notify the non transmitting BSSs also of the new bss color.
Signed-off-by: John Crispin <john@phrozen.org>
Co-developed-by: Lavanya Suresh <lavaks@codeaurora.org>
Signed-off-by: Lavanya Suresh <lavaks@codeaurora.org>
Co-developed-by: Rameshkumar Sundaram <quic_ramess@quicinc.com>
Signed-off-by: Rameshkumar Sundaram <quic_ramess@quicinc.com>
Link: https://lore.kernel.org/r/1637146647-16282-1-git-send-email-quic_ramess@quicinc.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Similar to cfg80211, introduce set_radar_offchan callback in mac80211_ops
in order to configure a dedicated offchannel chain available on some hw
(e.g. mt7915) to perform offchannel CAC detection and avoid tx/rx downtime.
Tested-by: Evelyn Tsai <evelyn.tsai@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Link: https://lore.kernel.org/r/201110606d4f3a7dfdf31440e351f2e2c375d4f0.1634979655.git.lorenzo@kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since commit a05829a722 ("cfg80211: avoid holding the RTNL when
calling the driver") we've not only been protecting the pointer
to monitor_sdata with the RTNL, but also with the wiphy->mtx. This
is relevant in a number of lockdep assertions, e.g. the one we hit
in ieee80211_set_monitor_channel(). However, we're now protecting
all the assignments/dereferences, even the one in interface iter,
with the wiphy->mtx, so switch over the lockdep assertions to that
lock.
Fixes: a05829a722 ("cfg80211: avoid holding the RTNL when calling the driver")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Link: https://lore.kernel.org/r/20211112135143.cb8e8ceffef3.Iaa210f16f6904c8a7a24954fb3396da0ef86ec08@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Configure multiple BSSID and enhanced multi-BSSID advertisement (EMA)
parameters in mac80211 for AP mode.
For each interface, 'mbssid_tx_vif' points to the transmitting interface of
the MBSSID set. The pointer is set to NULL if MBSSID is disabled.
Function ieee80211_stop() is modified to always bring down all the
non-transmitting interfaces first and the transmitting interface last.
Signed-off-by: John Crispin <john@phrozen.org>
Co-developed-by: Aloka Dixit <alokad@codeaurora.org>
Signed-off-by: Aloka Dixit <alokad@codeaurora.org>
Link: https://lore.kernel.org/r/20210916025437.29138-3-alokad@codeaurora.org
[slightly change logic to be more obvious]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The color change announcement is very similar to how CSA works where
we have an IE that includes a counter. When the counter hits 0, the new
color is applied via an updated beacon.
This patch makes the CSA counter functionality reusable, rather than
implementing it again. This also allows for future reuse incase support
for other counter IEs gets added.
Co-developed-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: John Crispin <john@phrozen.org>
Link: https://lore.kernel.org/r/057c1e67b82bee561ea44ce6a45a8462d3da6995.1625247619.git.lorenzo@kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Notify the driver about the 4-address mode change and also send a nulldata
packet to the AP to notify it about the change
Fixes: 1ff4e8f2de ("mac80211: notify the driver when a sta uses 4-address mode")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Link: https://lore.kernel.org/r/20210702050111.47546-1-nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This switches the airtime scheduler in mac80211 to use a virtual
time-based scheduler instead of the round-robin scheduler used before.
This has a couple of advantages:
- No need to sync up the round-robin scheduler in firmware/hardware with
the round-robin airtime scheduler.
- If several stations are eligible for transmission we can schedule both
of them; no need to hard-block the scheduling rotation until the head
of the queue has used up its quantum.
- The check of whether a station is eligible for transmission becomes
simpler (in ieee80211_txq_may_transmit()).
The drawback is that scheduling becomes slightly more expensive, as we
need to maintain an rbtree of TXQs sorted by virtual time. This means
that ieee80211_register_airtime() becomes O(logN) in the number of
currently scheduled TXQs because it can change the order of the
scheduled stations. We mitigate this overhead by only resorting when a
station changes position in the tree, and hopefully N rarely grows too
big (it's only TXQs currently backlogged, not all associated stations),
so it shouldn't be too big of an issue.
To prevent divisions in the fast path, we maintain both station sums and
pre-computed reciprocals of the sums. This turns the fast-path operation
into a multiplication, with divisions only happening as the number of
active stations change (to re-compute the current sum of all active
station weights). To prevent this re-computation of the reciprocal from
happening too frequently, we use a time-based notion of station
activity, instead of updating the weight every time a station gets
scheduled or de-scheduled. As queues can oscillate between empty and
occupied quite frequently, this can significantly cut down on the number
of re-computations. It also has the added benefit of making the station
airtime calculation independent on whether the queue happened to have
drained at the time an airtime value was accounted.
Co-developed-by: Yibo Zhao <yiboz@codeaurora.org>
Signed-off-by: Yibo Zhao <yiboz@codeaurora.org>
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Link: https://lore.kernel.org/r/20210623134755.235545-1-toke@redhat.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Conflicts:
MAINTAINERS
- keep Chandrasekar
drivers/net/ethernet/mellanox/mlx5/core/en_main.c
- simple fix + trust the code re-added to param.c in -next is fine
include/linux/bpf.h
- trivial
include/linux/ethtool.h
- trivial, fix kdoc while at it
include/linux/skmsg.h
- move to relevant place in tcp.c, comment re-wrapped
net/core/skmsg.c
- add the sk = sk // sk = NULL around calls
net/tipc/crypto.c
- trivial
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In some race conditions, with more clients and traffic configuration,
below crash is seen when making the interface down. sta->fast_rx wasn't
cleared when STA gets removed from 4-addr AP_VLAN interface. The crash is
due to try accessing 4-addr AP_VLAN interface's net_device (fast_rx->dev)
which has been deleted already.
Resolve this by clearing sta->fast_rx pointer when STA removes
from a 4-addr VLAN.
[ 239.449529] Unable to handle kernel NULL pointer dereference at virtual address 00000004
[ 239.449531] pgd = 80204000
...
[ 239.481496] CPU: 1 PID: 0 Comm: swapper/1 Not tainted 4.4.60 #227
[ 239.481591] Hardware name: Generic DT based system
[ 239.487665] task: be05b700 ti: be08e000 task.ti: be08e000
[ 239.492360] PC is at get_rps_cpu+0x2d4/0x31c
[ 239.497823] LR is at 0xbe08fc54
...
[ 239.778574] [<80739740>] (get_rps_cpu) from [<8073cb10>] (netif_receive_skb_internal+0x8c/0xac)
[ 239.786722] [<8073cb10>] (netif_receive_skb_internal) from [<8073d578>] (napi_gro_receive+0x48/0xc4)
[ 239.795267] [<8073d578>] (napi_gro_receive) from [<c7b83e8c>] (ieee80211_mark_rx_ba_filtered_frames+0xbcc/0x12d4 [mac80211])
[ 239.804776] [<c7b83e8c>] (ieee80211_mark_rx_ba_filtered_frames [mac80211]) from [<c7b84d4c>] (ieee80211_rx_napi+0x7b8/0x8c8 [mac8
0211])
[ 239.815857] [<c7b84d4c>] (ieee80211_rx_napi [mac80211]) from [<c7f63d7c>] (ath11k_dp_process_rx+0x7bc/0x8c8 [ath11k])
[ 239.827757] [<c7f63d7c>] (ath11k_dp_process_rx [ath11k]) from [<c7f5b6c4>] (ath11k_dp_service_srng+0x2c0/0x2e0 [ath11k])
[ 239.838484] [<c7f5b6c4>] (ath11k_dp_service_srng [ath11k]) from [<7f55b7dc>] (ath11k_ahb_ext_grp_napi_poll+0x20/0x84 [ath11k_ahb]
)
[ 239.849419] [<7f55b7dc>] (ath11k_ahb_ext_grp_napi_poll [ath11k_ahb]) from [<8073ce1c>] (net_rx_action+0xe0/0x28c)
[ 239.860945] [<8073ce1c>] (net_rx_action) from [<80324868>] (__do_softirq+0xe4/0x228)
[ 239.871269] [<80324868>] (__do_softirq) from [<80324c48>] (irq_exit+0x98/0x108)
[ 239.879080] [<80324c48>] (irq_exit) from [<8035c59c>] (__handle_domain_irq+0x90/0xb4)
[ 239.886114] [<8035c59c>] (__handle_domain_irq) from [<8030137c>] (gic_handle_irq+0x50/0x94)
[ 239.894100] [<8030137c>] (gic_handle_irq) from [<803024c0>] (__irq_svc+0x40/0x74)
Signed-off-by: Seevalamuthu Mariappan <seevalam@codeaurora.org>
Link: https://lore.kernel.org/r/1616163532-3881-1-git-send-email-seevalam@codeaurora.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Coverity reported the strange "if (~...)" condition that's
always true. It suggested that ! was intended instead of ~,
but upon further analysis I'm convinced that what really was
intended was a comparison to 0xff/0xffff (in HT/VHT cases
respectively), since this indicates that all of the rates
are enabled.
Change the comparison accordingly.
I'm guessing this never really mattered because a reset to
not having a rate mask is basically equivalent to having a
mask that enables all rates.
Reported-by: Colin Ian King <colin.king@canonical.com>
Fixes: 2ffbe6d333 ("mac80211: fix and optimize MCS mask handling")
Fixes: b119ad6e72 ("mac80211: add rate mask logic for vht rates")
Reviewed-by: Colin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20210212112213.36b38078f569.I8546a20c80bc1669058eb453e213630b846e107b@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This change registers ieee80211_set_sar_specs to
mac80211_config_ops, so cfg80211 can call it.
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Reviewed-by: Abhishek Kumar <kuabhs@chromium.org>
Link: https://lore.kernel.org/r/20201203103728.3034-3-cjhuang@codeaurora.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We don't really use this struct, we're now using
struct cfg80211_he_bss_color instead.
Change the one place in mac80211 that's using the old
name to use struct assignment instead of memcpy() and
thus remove the wrong sizeof while at it.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20201206145305.f6698d97ae4e.Iba2dffcb79c4ab80bde7407609806010b55edfdf@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The user is allowed to change beacon tx rate (HT/VHT/HE) from hostapd.
This information needs to be passed to the driver when the rate control
is offloaded to the firmware. The driver capability of allowing beacon
rate is already validated in cfg80211, so simply passing the rate
information to the driver is enough.
Signed-off-by: Rajkumar Manoharan <rmanohar@codeaurora.org>
Link: https://lore.kernel.org/r/1601762658-15627-1-git-send-email-rmanohar@codeaurora.org
[adjust commit message slightly]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Even though a driver or mac80211 shouldn't produce a
legacy bitrate if sband->bitrates doesn't exist, don't
crash if that is the case either.
This fixes a kernel panic if station dump is run before
last_rate can be updated with a data frame when
sband->bitrates is missing (eg. in S1G bands).
Signed-off-by: Thomas Pedersen <thomas@adapt-ip.com>
Link: https://lore.kernel.org/r/20201005164522.18069-1-thomas@adapt-ip.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The changes required for associating in S1G are:
- apply S1G BSS channel info before assoc
- mark all S1G STAs as QoS STAs
- include and parse AID request element
- handle new Association Response format
- don't fail assoc if supported rates element is missing
Signed-off-by: Thomas Pedersen <thomas@adapt-ip.com>
Link: https://lore.kernel.org/r/20200922022818.15855-15-thomas@adapt-ip.com
[pass skb to ieee80211_add_aid_request_ie(), remove unused variable 'bss']
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This patch adds mac80211 support to configure unsolicited
broadcast probe response transmission for in-band discovery in 6GHz.
Changes include functions to store and retrieve probe response template,
and packet interval (0 - 20 TUs).
Setting interval to 0 disables the unsolicited broadcast probe response
transmission.
Signed-off-by: Aloka Dixit <alokad@codeaurora.org>
Link: https://lore.kernel.org/r/010101747a946b35-ad25858a-1f1f-48df-909e-dc7bf26d9169-000000@us-west-2.amazonses.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We want to reuse the functions and structs for other counters such as BSS
color change. Rename them to more generic names.
Signed-off-by: John Crispin <john@phrozen.org>
Link: https://lore.kernel.org/r/20200811080107.3615705-2-john@phrozen.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This is in fact 'disabled' in the spec, but there it's in a
place where that actually makes sense. In our internal data
structures, it doesn't really make sense, and in fact the
previous commit just fixed a bug in that area.
Make this safer by inverting the polarity from 'disabled' to
'enabled'.
Link: https://lore.kernel.org/r/20200730130051.5d8399545bd9.Ie62fdcd1a6cd9c969315bc124084a494ca6c8df3@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Adding bss-color configuration is only valid in HE mode.
Earlier we have enabled it by default, irrespective of
capabilities/mode. Fix that.
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Rajkumar Manoharan <rmanohar@codeaurora.org>
Signed-off-by: P Praneesh <ppranees@codeaurora.org>
Link: https://lore.kernel.org/r/1594262781-21444-1-git-send-email-ppranees@codeaurora.org
[fix up commit message]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Besides information about num of peerings and gate connectivity,
the mesh formation byte also contains a flag for authentication
server connectivity, that currently cannot be set in the mesh conf.
This patch adds this capability, which is necessary to implement
802.1X authentication in mesh mode.
Signed-off-by: Markus Theil <markus.theil@tu-ilmenau.de>
Link: https://lore.kernel.org/r/20200611140238.427461-1-markus.theil@tu-ilmenau.de
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently, before being able to forward a packet between two 802.11s
nodes, both a PLINK handshake is performed upon receiving a beacon and
then later a PREQ/PREP exchange for path discovery is performed on
demand upon receiving a data frame to forward.
When running a mesh protocol on top of an 802.11s interface, like
batman-adv, we do not need the multi-hop mesh routing capabilities of
802.11s and usually set mesh_fwding=0. However, even with mesh_fwding=0
the PREQ/PREP path discovery is still performed on demand. Even though
in this scenario the next hop PREQ/PREP will determine is always the
direct 11s neighbor node.
The new mesh_nolearn parameter allows to skip the PREQ/PREP exchange in
this scenario, leading to a reduced delay, reduced packet buffering and
simplifies HWMP in general.
mesh_nolearn is still rather conservative in that if the packet destination
is not a direct 11s neighbor, it will fall back to PREQ/PREP path
discovery.
For normal, multi-hop 802.11s mesh routing it is usually not advisable
to enable mesh_nolearn as a transmission to a direct but distant neighbor
might be worse than reaching that same node via a more robust /
higher throughput etc. multi-hop path.
Cc: Sven Eckelmann <sven@narfation.org>
Cc: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Linus Lüssing <ll@simonwunderlich.de>
Link: https://lore.kernel.org/r/20200617073034.26149-1-linus.luessing@c0d3.blue
[fix nl80211 policy to range 0/1 only]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Use the Beacon frame specific legacy rate configuration, if specified
for AP or mesh, instead of the generic rate mask when selecting the TX
rate for Beacon frames.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Link: https://lore.kernel.org/r/20200425155713.25687-4-jouni@codeaurora.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
cfg80211_chan_def and ieee80211_channel recently gained a
frequency offset component. Handle this where it makes
sense (potentially required by S1G channels).
For IBSS, TDLS, CSA, and ROC we return -EOPNOTSUPP if a
channel with frequency offset is passed, since they may or
may not work. Once someone tests and verifies these
commands work on thos types of channels, we can remove
that error.
join_ocb and join_mesh look harmless because they use a
simple ieee80211_vif_use_channel(), which is using an
already verified channel, so we let those through.
Signed-off-by: Thomas Pedersen <thomas@adapt-ip.com>
Link: https://lore.kernel.org/r/20200402011810.22947-4-thomas@adapt-ip.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Convert a user space registration for processing multicast Action frames
(NL80211_CMD_REGISTER_FRAME with NL80211_ATTR_RECEIVE_MULTICAST) to a
new enum ieee80211_filter_flags bit FIF_MCAST_ACTION so that drivers can
update their RX filter parameters appropriately, if needed.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Link: https://lore.kernel.org/r/20200421144815.19175-1-jouni@codeaurora.org
[rename variables to rx_mcast_action_reg indicating action frames only]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Almost all drivers below cfg80211 get the API wrong (except for
cfg80211) and are unable to cope with multiple registrations for
the same frame type, which is valid due to the match filter.
This seems to indicate the API is wrong, and we should maintain
the full information in cfg80211 instead of the drivers.
Change the API to no longer inform the driver about individual
registrations and unregistrations, but rather every time about
the entire state of the entire wiphy and single wdev, whenever
it may have changed. This also simplifies the code in cfg80211
as it no longer has to track exactly what was unregistered and
can free things immediately.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Reviewed-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Link: https://lore.kernel.org/r/20200417124300.f47f3828afc8.I7f81ef59c2c5a340d7075fb3c6d0e08e8aeffe07@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There are two bugs with this, first, it shouldn't be called
on an interface that's down, and secondly, it should then be
called when the interface comes up.
Note that the currently only user (iwlwifi) doesn't seem to
care about either of these scenarios.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Link: https://lore.kernel.org/r/20200417111830.401d82c7a0bf.I5dc7d718816460c2d8d89c7af6c215f9e2b3078f@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In AP mode, set htc_trig_based_pkt_ext and frame_time_rts_th
for driver use.
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/20200131111300.891737-19-luca@coelho.fi
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This patch adds support for disabling pre-auth rx over the nl80211 control
port for mac80211.
Signed-off-by: Markus Theil <markus.theil@tu-ilmenau.de>
Link: https://lore.kernel.org/r/20200312091055.54257-3-markus.theil@tu-ilmenau.de
[fix indentation slightly, squash feature enablement]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Implement drv_set_tid_config api to allow TID specific
configuration and drv_reset_tid_config api to reset peer
specific TID configuration. This per-TID onfiguration
will be applied for all the connected stations when MAC is NULL.
Signed-off-by: Tamizh chelvam <tamizhr@codeaurora.org>
Link: https://lore.kernel.org/r/1579506687-18296-7-git-send-email-tamizhr@codeaurora.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Extend mac80211 key configuration to support the new BIGTK with key
index values 6 and 7. Support for actually protecting Beacon frames
(adding the MME in AP mode and checking it in STA mode) is covered in
separate commits.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Link: https://lore.kernel.org/r/20200222132548.20835-3-jouni@codeaurora.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* 802.11 frame encapsulation offload support
* more HE (802.11ax) support, including some for 6 GHz band
* powersave in hwsim, for better testing
Of course as usual there are various cleanups and small fixes.
-----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEEH1e1rEeCd0AIMq6MB8qZga/fl8QFAl5GggsACgkQB8qZga/f
l8Qgdg//R42bSv94JYPcwZ5phgTgraCRZODWjBJq08n2T5m0EmEufgX79d9uEdgT
u9npvn+ich5/VZhmuSbGrW9TT6/FPLAZyghV1fj79o971Qd7ky2Mp8G1fcTEbtDn
IG2e9vauY9XDSb2O3wNj8dA8rAN/kLNmhsPqWxn2CgLPqjdbf+W15dvo4rnaL2gs
ffGyE47dHuAFwCruyT8UPbw3iu4+tQhruN9eVg+UkU8rJGvEMqfrLK20zl1weIV9
a7IuXdxacdsHO8Y+tl6GtvgOURQPpvf55+leLOUhcmHPJ3f/eAal6wmWRxDxs/qB
IWSe8BC81cZZ5pYWk1A+0sXfJMlYjNsN0xw5SQRSrbgyb5saz8aLUIlHsOBM4iPH
SwzCMN5A1GOPOUFsugzPwbiki9g6dh0/EC2NyXE4A26CAd967dVXTvTY5SMNgiB+
bZaaUDaPQUm1jgDT5bLRhTipTHbekDkYzG/e+wNO+HKyStoEYM485MwY4MQCYzEh
HKDmkAbFuCwEUeXXw1y8GybUknApCRru9FtY+oiN/+y/aESfB7HJfmDFFU/KYgPu
HOuqJoNAxdMdycDCb24/cLjUiehzfM6sujwBxZOD5WHhAcXrBo5dGd6ibfurIrjj
XI36/mwTiMtyyb0/5xM1AKvoic2j+a5YU3MB7KSc9TlaPa5j2NA=
=CgmJ
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-net-next-2020-02-14' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
A few big new things:
* 802.11 frame encapsulation offload support
* more HE (802.11ax) support, including some for 6 GHz band
* powersave in hwsim, for better testing
Of course as usual there are various cleanups and small fixes.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The SMPS feature is defined in the specification only to be
used by non-AP stations and not by APs, so remove the support
for changing the AP's SMPS mode dynamically.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/20200131111300.891737-20-luca@coelho.fi
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
It turns out that this wasn't a good idea, I hit a test failure in
hwsim due to this. That particular failure was easily worked around,
but it raised questions: if an AP needs to, for example, send action
frames to each connected station, the current limit is nowhere near
enough (especially if those stations are sleeping and the frames are
queued for a while.)
Shuffle around some bits to make more room for ack_frame_id to allow
up to 8192 queued up frames, that's enough for queueing 4 frames to
each connected station, even at the maximum of 2007 stations on a
single AP.
We take the bits from band (which currently only 2 but I leave 3 in
case we add another band) and from the hw_queue, which can only need
4 since it has a limit of 16 queues.
Fixes: 6912daed05 ("mac80211: Shrink the size of ack_frame_id to make room for tx_time_est")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Acked-by: Toke Høiland-Jørgensen <toke@redhat.com>
Link: https://lore.kernel.org/r/20200115122549.b9a4ef9f4980.Ied52ed90150220b83a280009c590b65d125d087c@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
It is now possible to propagate BSS color settings into the subsystem. Lets
make mac80211 also handle them so that we can send them further down the
stack into the drivers. We drop the old bss_color field and change iwlwifi
to use the new he_bss_color struct.
Signed-off-by: John Crispin <john@phrozen.org>
Link: https://lore.kernel.org/r/20191217141921.8114-2-john@phrozen.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In case a radar event of CAC_FINISHED or RADAR_DETECTED
happens during another phy is during CAC we might need
to cancel that CAC.
If we got a radar in a channel that another phy is now
doing CAC on then the CAC should be canceled there.
If, for example, 2 phys doing CAC on the same channels,
or on comptable channels, once on of them will finish his
CAC the other might need to cancel his CAC, since it is no
longer relevant.
To fix that the commit adds an callback and implement it in
mac80211 to end CAC.
This commit also adds a call to said callback if after a radar
event we see the CAC is no longer relevant
Signed-off-by: Orr Mazor <Orr.Mazor@tandemg.com>
Reviewed-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Link: https://lore.kernel.org/r/20191222145449.15792-1-Orr.Mazor@tandemg.com
[slightly reformat/reword commit message]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
To implement airtime queue limiting, we need to keep a running account of
the estimated airtime of all skbs queued into the device. Do to this
correctly, we need to store the airtime estimate into the skb so we can
decrease the outstanding balance when the skb is freed. This means that the
time estimate must be stored somewhere that will survive for the lifetime
of the skb.
To get this, decrease the size of the ack_frame_id field to 6 bits, and
lower the size of the ID space accordingly. This leaves 10 bits for use for
tx_time_est, which is enough to store a maximum of 4096 us, if we shift the
values so they become units of 4us.
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Link: https://lore.kernel.org/r/157182474063.150713.16132669599100802716.stgit@toke.dk
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The Layer 2 Update frame is used to update bridges when a station roams
to another AP even if that STA does not transmit any frames after the
reassociation. This behavior was described in IEEE Std 802.11F-2003 as
something that would happen based on MLME-ASSOCIATE.indication, i.e.,
before completing 4-way handshake. However, this IEEE trial-use
recommended practice document was published before RSN (IEEE Std
802.11i-2004) and as such, did not consider RSN use cases. Furthermore,
IEEE Std 802.11F-2003 was withdrawn in 2006 and as such, has not been
maintained amd should not be used anymore.
Sending out the Layer 2 Update frame immediately after association is
fine for open networks (and also when using SAE, FT protocol, or FILS
authentication when the station is actually authenticated by the time
association completes). However, it is not appropriate for cases where
RSN is used with PSK or EAP authentication since the station is actually
fully authenticated only once the 4-way handshake completes after
authentication and attackers might be able to use the unauthenticated
triggering of Layer 2 Update frame transmission to disrupt bridge
behavior.
Fix this by postponing transmission of the Layer 2 Update frame from
station entry addition to the point when the station entry is marked
authorized. Similarly, send out the VLAN binding update only if the STA
entry has already been authorized.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Store the OBSS PD parameters inside bss_conf when bringing up an AP and/or
when a station connects to an AP. This allows the driver to configure the
HW accordingly.
Signed-off-by: John Crispin <john@phrozen.org>
Link: https://lore.kernel.org/r/20190730163701.18836-3-john@phrozen.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This came up in fuzz testing, and really we don't consider
all-zeroes to be a valid MAC address in most places, so
also reject it here to avoid confusion later on.
Signed-off-by: Karthikeyan Periyasamy <periyasa@codeaurora.org>
Link: https://lore.kernel.org/r/1563959770-21570-1-git-send-email-periyasa@codeaurora.org
[rewrite commit message]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Pull networking updates from David Miller:
"Some highlights from this development cycle:
1) Big refactoring of ipv6 route and neigh handling to support
nexthop objects configurable as units from userspace. From David
Ahern.
2) Convert explored_states in BPF verifier into a hash table,
significantly decreased state held for programs with bpf2bpf
calls, from Alexei Starovoitov.
3) Implement bpf_send_signal() helper, from Yonghong Song.
4) Various classifier enhancements to mvpp2 driver, from Maxime
Chevallier.
5) Add aRFS support to hns3 driver, from Jian Shen.
6) Fix use after free in inet frags by allocating fqdirs dynamically
and reworking how rhashtable dismantle occurs, from Eric Dumazet.
7) Add act_ctinfo packet classifier action, from Kevin
Darbyshire-Bryant.
8) Add TFO key backup infrastructure, from Jason Baron.
9) Remove several old and unused ISDN drivers, from Arnd Bergmann.
10) Add devlink notifications for flash update status to mlxsw driver,
from Jiri Pirko.
11) Lots of kTLS offload infrastructure fixes, from Jakub Kicinski.
12) Add support for mv88e6250 DSA chips, from Rasmus Villemoes.
13) Various enhancements to ipv6 flow label handling, from Eric
Dumazet and Willem de Bruijn.
14) Support TLS offload in nfp driver, from Jakub Kicinski, Dirk van
der Merwe, and others.
15) Various improvements to axienet driver including converting it to
phylink, from Robert Hancock.
16) Add PTP support to sja1105 DSA driver, from Vladimir Oltean.
17) Add mqprio qdisc offload support to dpaa2-eth, from Ioana
Radulescu.
18) Add devlink health reporting to mlx5, from Moshe Shemesh.
19) Convert stmmac over to phylink, from Jose Abreu.
20) Add PTP PHC (Physical Hardware Clock) support to mlxsw, from
Shalom Toledo.
21) Add nftables SYNPROXY support, from Fernando Fernandez Mancera.
22) Convert tcp_fastopen over to use SipHash, from Ard Biesheuvel.
23) Track spill/fill of constants in BPF verifier, from Alexei
Starovoitov.
24) Support bounded loops in BPF, from Alexei Starovoitov.
25) Various page_pool API fixes and improvements, from Jesper Dangaard
Brouer.
26) Just like ipv4, support ref-countless ipv6 route handling. From
Wei Wang.
27) Support VLAN offloading in aquantia driver, from Igor Russkikh.
28) Add AF_XDP zero-copy support to mlx5, from Maxim Mikityanskiy.
29) Add flower GRE encap/decap support to nfp driver, from Pieter
Jansen van Vuuren.
30) Protect against stack overflow when using act_mirred, from John
Hurley.
31) Allow devmap map lookups from eBPF, from Toke Høiland-Jørgensen.
32) Use page_pool API in netsec driver, Ilias Apalodimas.
33) Add Google gve network driver, from Catherine Sullivan.
34) More indirect call avoidance, from Paolo Abeni.
35) Add kTLS TX HW offload support to mlx5, from Tariq Toukan.
36) Add XDP_REDIRECT support to bnxt_en, from Andy Gospodarek.
37) Add MPLS manipulation actions to TC, from John Hurley.
38) Add sending a packet to connection tracking from TC actions, and
then allow flower classifier matching on conntrack state. From
Paul Blakey.
39) Netfilter hw offload support, from Pablo Neira Ayuso"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (2080 commits)
net/mlx5e: Return in default case statement in tx_post_resync_params
mlx5: Return -EINVAL when WARN_ON_ONCE triggers in mlx5e_tls_resync().
net: dsa: add support for BRIDGE_MROUTER attribute
pkt_sched: Include const.h
net: netsec: remove static declaration for netsec_set_tx_de()
net: netsec: remove superfluous if statement
netfilter: nf_tables: add hardware offload support
net: flow_offload: rename tc_cls_flower_offload to flow_cls_offload
net: flow_offload: add flow_block_cb_is_busy() and use it
net: sched: remove tcf block API
drivers: net: use flow block API
net: sched: use flow block API
net: flow_offload: add flow_block_cb_{priv, incref, decref}()
net: flow_offload: add list handling functions
net: flow_offload: add flow_block_cb_alloc() and flow_block_cb_free()
net: flow_offload: rename TCF_BLOCK_BINDER_TYPE_* to FLOW_BLOCK_BINDER_TYPE_*
net: flow_offload: rename TC_BLOCK_{UN}BIND to FLOW_BLOCK_{UN}BIND
net: flow_offload: add flow_block_cb_setup_simple()
net: hisilicon: Add an tx_desc to adapt HI13X1_GMAC
net: hisilicon: Add an rx_desc to adapt HI13X1_GMAC
...
Pull crypto updates from Herbert Xu:
"Here is the crypto update for 5.3:
API:
- Test shash interface directly in testmgr
- cra_driver_name is now mandatory
Algorithms:
- Replace arc4 crypto_cipher with library helper
- Implement 5 way interleave for ECB, CBC and CTR on arm64
- Add xxhash
- Add continuous self-test on noise source to drbg
- Update jitter RNG
Drivers:
- Add support for SHA204A random number generator
- Add support for 7211 in iproc-rng200
- Fix fuzz test failures in inside-secure
- Fix fuzz test failures in talitos
- Fix fuzz test failures in qat"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (143 commits)
crypto: stm32/hash - remove interruptible condition for dma
crypto: stm32/hash - Fix hmac issue more than 256 bytes
crypto: stm32/crc32 - rename driver file
crypto: amcc - remove memset after dma_alloc_coherent
crypto: ccp - Switch to SPDX license identifiers
crypto: ccp - Validate the the error value used to index error messages
crypto: doc - Fix formatting of new crypto engine content
crypto: doc - Add parameter documentation
crypto: arm64/aes-ce - implement 5 way interleave for ECB, CBC and CTR
crypto: arm64/aes-ce - add 5 way interleave routines
crypto: talitos - drop icv_ool
crypto: talitos - fix hash on SEC1.
crypto: talitos - move struct talitos_edesc into talitos.h
lib/scatterlist: Fix mapping iterator when sg->offset is greater than PAGE_SIZE
crypto/NX: Set receive window credits to max number of CRBs in RxFIFO
crypto: asymmetric_keys - select CRYPTO_HASH where needed
crypto: serpent - mark __serpent_setkey_sbox noinline
crypto: testmgr - dynamically allocate crypto_shash
crypto: testmgr - dynamically allocate testvec_config
crypto: talitos - eliminate unneeded 'done' functions at build time
...
The WEP code in the mac80211 subsystem currently uses the crypto
API to access the arc4 (RC4) cipher, which is overly complicated,
and doesn't really have an upside in this particular case, since
ciphers are always synchronous and therefore always implemented in
software. Given that we have no accelerated software implementations
either, it is much more straightforward to invoke a generic library
interface directly.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Even if we have a station, we currently call rate_control_send_low()
with the NULL station unless further rate control (driver, minstrel)
has been initialized.
Change this so we can use more information about the station to use
a better rate. For example, when we associate with an AP, we will
now use the lowest rate it advertised as supported (that we can)
rather than the lowest mandatory rate. This aligns our behaviour
with most other 802.11 implementations.
To make this possible, we need to also ensure that we have non-zero
rates at all times, so in case we really have *nothing* pre-fill
the supp_rates bitmap with the very lowest mandatory bitmap (11b
and 11a on 2.4 and 5 GHz respectively).
Additionally, hostapd appears to be giving us an empty supported
rates bitmap (it can and should do better, since the STA must have
supported for at least the basic rates in the BSS), so ignore any
such bitmaps that would actually zero out the supp_rates, and in
that case just keep the pre-filled mandatory rates.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Allow the userland daemon to en/disable TWT support for an AP.
Signed-off-by: Shashidhar Lakkavalli <slakkavalli@datto.com>
Signed-off-by: John Crispin <john@phrozen.org>
[simplify parsing code]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Based on 1 normalized pattern(s):
this file is gplv2 as found in copying
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 4 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190531190114.657082701@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The requirement for mesh link metric refreshing, is that from one
mesh point we be able to send some data frames to other mesh points
which are not currently selected as a primary traffic path, but which
are only 1 hop away. The absence of the primary path to the chosen node
makes it necessary to apply some form of marking on a chosen packet
stream so that the packets can be properly steered to the selected node
for testing, and not by the regular mesh path lookup.
Tested-by: Pradeep Kumar Chitrapu <pradeepc@codeaurora.org>
Signed-off-by: Rajkumar Manoharan <rmanohar@codeaurora.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This patch introduce a new driver callback drv_sta_set_txpwr. This API will
copy the transmit power value passed from user space and call the driver
callback to set the tx power for the station.
Co-developed-by: Balaji Pothunoori <bpothuno@codeaurora.org>
Signed-off-by: Ashok Raj Nagarajan <arnagara@codeaurora.org>
Signed-off-by: Balaji Pothunoori <bpothuno@codeaurora.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add support for Extended Key ID as defined in IEEE 802.11-2016.
- Implement the nl80211 API for Extended Key ID
- Extend mac80211 API to allow drivers to support Extended Key ID
- Enable Extended Key ID by default for drivers only supporting SW
crypto (e.g. mac80211_hwsim)
- Allow unicast Tx usage to be supressed (IEEE80211_KEY_FLAG_NO_AUTO_TX)
- Select the decryption key based on the MPDU keyid
- Enforce existing assumptions in the code that rekeys don't change the
cipher
Signed-off-by: Alexander Wetzel <alexander@wetzel-home.de>
[remove module parameter]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The starting of AP interface can fail due to invalid
beacon interval, which does not match the minimum gcd
requirement set by the wifi driver. In such case, the
beacon interval of that interface gets updated with
that invalid beacon interval.
The next time that interface is brought up in AP mode,
an interface combination check is performed and the
beacon interval is taken from the previously set value.
In a case where an invalid beacon interval, i.e. a beacon
interval value which does not satisfy the minimum gcd criteria
set by the driver, is set, all the subsequent trials to
bring that interface in AP mode will fail, even if the
subsequent trials have a valid beacon interval.
To avoid this, in case of a failure in bringing up an
interface in AP mode due to interface combination error,
the interface beacon interval which is stored in bss
conf, needs to be restored with the last working value
of beacon interval.
Tested on ath10k using WCN3990.
Cc: stable@vger.kernel.org
Fixes: 0c317a02ca ("cfg80211: support virtual interfaces with different beacon intervals")
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Merge net-next so that we get the changes from net, which would
otherwise conflict with the NLA_POLICY_NESTED/_ARRAY changes.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Use bitrate moving average to smooth out link metric and stablize path
selection.
Signed-off-by: Julan Hsu <julanhsu@google.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Expose path change count to destination in mpath info
Signed-off-by: Julan Hsu <julanhsu@google.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Expose hop count to destination information in mpath info
Signed-off-by: Julan Hsu <julanhsu@google.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This adds airtime accounting and scheduling to the mac80211 TXQ
scheduler. A new callback, ieee80211_sta_register_airtime(), is added
that drivers can call to report airtime usage for stations.
When airtime information is present, mac80211 will schedule TXQs
(through ieee80211_next_txq()) in a way that enforces airtime fairness
between active stations. This scheduling works the same way as the ath9k
in-driver airtime fairness scheduling. If no airtime usage is reported
by the driver, the scheduler will default to round-robin scheduling.
For drivers that don't control TXQ scheduling in software, a new API
function, ieee80211_txq_may_transmit(), is added which the driver can use
to check if the TXQ is eligible for transmission, or should be throttled to
enforce fairness. Calls to this function must also be enclosed in
ieee80211_txq_schedule_{start,end}() calls to ensure proper locking.
The API ieee80211_txq_may_transmit() also ensures that TXQ list will be
aligned aginst driver's own round-robin scheduler list. i.e it rotates
the TXQ list till it makes the requested node becomes the first entry
in TXQ list. Thus both the TXQ list and driver's list are in sync.
Co-developed-by: Rajkumar Manoharan <rmanohar@codeaurora.org>
Signed-off-by: Louie Lu <git@louie.lu>
[added debugfs write op to reset airtime counter]
Signed-off-by: Toke Høiland-Jørgensen <toke@toke.dk>
Signed-off-by: Rajkumar Manoharan <rmanohar@codeaurora.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* virt_wifi - wireless control simulation on top of
another network interface
* hwsim configurability to test capabilities similar
to real hardware
* various mesh improvements
* various radiotap vendor data fixes in mac80211
* finally the nl_set_extack_cookie_u64() we talked
about previously, used for
* peer measurement APIs, right now only with FTM
(flight time measurement) for location
* made nl80211 radio/interface announcements more complete
* various new HE (802.11ax) things:
updates, TWT support, ...
-----BEGIN PGP SIGNATURE-----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=EpyK
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-davem-2018-12-19' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
This time we have too many changes to list, highlights:
* virt_wifi - wireless control simulation on top of
another network interface
* hwsim configurability to test capabilities similar
to real hardware
* various mesh improvements
* various radiotap vendor data fixes in mac80211
* finally the nl_set_extack_cookie_u64() we talked
about previously, used for
* peer measurement APIs, right now only with FTM
(flight time measurement) for location
* made nl80211 radio/interface announcements more complete
* various new HE (802.11ax) things:
updates, TWT support, ...
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The pointer and corresponding length is always set in pairs
in cfg80211, so no need to have this strange defensive check
that also confuses static checkers. Clean it up.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When userspace is controlling mesh routing, it may have better
knowledge about whether a mesh STA is connected to a mesh
gate than the kernel mpath table. Add dot11MeshConnectedToMeshGate
to the mesh config so that such applications can explicitly
signal that a mesh STA is connected to a gate, which will then
be advertised in the beacon.
Signed-off-by: Bob Copeland <bobcopeland@fb.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There's nothing much for mac80211 to do, so only pass through
the requests with minimal checks and tracing. The driver must
call cfg80211's results APIs.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If the FTM responder settings are changed simultaneously with
the CSA beacon, the buffer size allocated isn't sufficient and
we'll have a heap overrun. Fix this.
While at it, also clean up the ftm_responder assignment, doing
it only if ftm_responder is non-zero is valid as it's 0 to start
with, but not really useful to understand the code.
Fixes: bc847970f4 ("mac80211: support FTM responder configuration/statistics")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
New bss param ftm_responder is used to notify the driver to
enable fine timing request (FTM) responder role in AP mode.
Plumb the new cfg80211 API for FTM responder statistics through to
the driver API in mac80211.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Pradeep Kumar Chitrapu <pradeepc@codeaurora.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
key->sta is only valid after ieee80211_key_link, which is called later
in this function. Because of that, the IEEE80211_KEY_FLAG_RX_MGMT is
never set when management frame protection is enabled.
Fixes: e548c49e6d ("mac80211: add key flag for management keys")
Cc: stable@vger.kernel.org
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In AP mode, If AP advertises HE capabilities, set to true
bss_conf::he_supported so that the Driver knows about it.
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
These checks aren't necessary, cfg80211 never passes NULL.
Some static checkers complain about the missing checks on
the next line, but really the NULL checks are unnecessary.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Make ieee80211_send_layer2_update() a common function so other drivers
can re-use it.
Signed-off-by: Dedy Lansky <dlansky@codeaurora.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
As explained in ieee80211_delayed_tailroom_dec(), during roam,
keys of the old AP will be destroyed and new keys will be
installed. Deletion of the old key causes
crypto_tx_tailroom_needed_cnt to go from 1 to 0 and the new key
installation causes a transition from 0 to 1.
Whenever crypto_tx_tailroom_needed_cnt transitions from 0 to 1,
we invoke synchronize_net(); the reason for doing this is to avoid
a race in the TX path as explained in increment_tailroom_need_count().
This synchronize_net() operation can be slow and can affect the station
roam time. To avoid this, decrementing the crypto_tx_tailroom_needed_cnt
is delayed for a while so that upon installation of new key the
transition would be from 1 to 2 instead of 0 to 1 and thereby
improving the roam time.
This is all correct for a STA iftype, but deferring the tailroom_needed
decrement for other iftypes may be unnecessary.
For example, let's consider the case of a 4-addr client connecting to
an AP for which AP_VLAN interface is also created, let the initial
value for tailroom_needed on the AP be 1.
* 4-addr client connects to the AP (AP: tailroom_needed = 1)
* AP will clear old keys, delay decrement of tailroom_needed count
* AP_VLAN is created, it takes the tailroom count from master
(AP_VLAN: tailroom_needed = 1, AP: tailroom_needed = 1)
* Install new key for the station, assume key is plumbed in the HW,
there won't be any change in tailroom_needed count on AP iface
* Delayed decrement of tailroom_needed count on AP
(AP: tailroom_needed = 0, AP_VLAN: tailroom_needed = 1)
Because of the delayed decrement on AP iface, tailroom_needed count goes
out of sync between AP(master iface) and AP_VLAN(slave iface) and
there would be unnecessary tailroom created for the packets going
through AP_VLAN iface.
Also, WARN_ONs were observed while trying to bring down the AP_VLAN
interface:
(warn_slowpath_common) (warn_slowpath_null+0x18/0x20)
(warn_slowpath_null) (ieee80211_free_keys+0x114/0x1e4)
(ieee80211_free_keys) (ieee80211_del_virtual_monitor+0x51c/0x850)
(ieee80211_del_virtual_monitor) (ieee80211_stop+0x30/0x3c)
(ieee80211_stop) (__dev_close_many+0x94/0xb8)
(__dev_close_many) (dev_close_many+0x5c/0xc8)
Restricting delayed decrement to station interface alone fixes the problem
and it makes sense to do so because delayed decrement is done to improve
roam time which is applicable only for client devices.
Signed-off-by: Manikanta Pubbisetty <mpubbise@codeaurora.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add support for HE in mac80211 conforming with P802.11ax_D1.4.
Johannes: Fix another bug with the buf_size comparison in agg-rx.c.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Ido Yariv <idox.yariv@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Support the new random SN and minimal probe request contents
scan flags for the case of software scan - for hardware scan
the drivers need to opt in, but may need to do only that,
depending on their implementation.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
This fixes memory leaks in the case where we just have the
station info on the stack for internal usage without sending
it to cfg80211.
Fixes: 8689c051a2 ("cfg80211: dynamically allocate per-tid stats for station info")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This adds support to mac80211 to export TXQ stats via the newly added
cfg80211 API.
Signed-off-by: Toke Høiland-Jørgensen <toke@toke.dk>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If userspace requested control port frames to go over 80211, then do so.
The control packets are intercepted just prior to delivery of the packet
to the underlying network device.
Pre-authentication type frames (protocol: 0x88c7) are also forwarded
over nl80211.
Signed-off-by: Denis Kenzior <denkenz@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
ETSI has recently added new requirements that restrict the WMM
parameter values for 5GHz frequencies. We need to take care of the
following scenarios in order to comply with these new requirements:
1. When using mac80211 default values;
2. When the userspace tries to configure its own values;
3. When associating to an AP which advertises WWM IE.
When associating to an AP, the client uses the values in the
advertised WMM IE. But the AP may not comply with the new ETSI
requirements, so the client needs to check the current regulatory
rules and use those limits accordingly.
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
With drivers implementing rate control in driver or firmware
rate_control_send_low() may not get called, and thus the
driver needs to know about changes in the multicast rate.
Add and use a new BSS change flag for this.
Signed-off-by: Pradeep Kumar Chitrapu <pradeepc@codeaurora.org>
[rewrite commit message]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When powersave is disabled for the interface, we can do fast-rx anyway.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
[fixed indentation on one line]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Johannes Berg