The return value from kzalloc() is not checked correctly. The
test is done against a wrong variable. This patch fix it.
Fixes: f25da51fdc ("ieee802154: hwsim: add replacement for fakelb")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds missing rcu_assign_pointer()/rcu_dereference() to used rcu
pointers. There was already a previous commit c5d99d2b35 ("ieee802154:
hwsim: fix rcu address annotation"), but there was more which was
pointed out on my side by using newest sparse version.
Cc: Stefan Schmidt <stefan@datenfreihafen.org>
Fixes: f25da51fdc ("ieee802154: hwsim: add replacement for fakelb")
Signed-off-by: Alexander Aring <aring@mojatatu.com>
Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the problem below. The problem can be reproduced by the
following steps:
1) Connecting all HiNIC interfaces
2) On server side
# sudo ifconfig eth0 192.168.100.1 up #Using MLX CX4 card
# iperf -s
3) On client side
# sudo ifconfig eth0 192.168.100.2 up #Using our HiNIC card
# iperf -c 192.168.101.1 -P 10 -t 100000
after hours of testing, we will see errors:
hinic 0000:05:00.0: No MGMT msg handler, mod = 0
hinic 0000:05:00.0: No MGMT msg handler, mod = 0
hinic 0000:05:00.0: No MGMT msg handler, mod = 0
hinic 0000:05:00.0: No MGMT msg handler, mod = 0
The errors are caused by the following problem.
1) The hinic_get_wqe() checks the "wq->delta" to allocate new WQEs:
if (atomic_sub_return(num_wqebbs, &wq->delta) <= 0) {
atomic_add(num_wqebbs, &wq->delta);
return ERR_PTR(-EBUSY);
}
If the WQE occupies multiple pages, the shadow WQE will be used. Then the
hinic_xmit_frame() fills the WQE.
2) While in parallel with 1), the free_tx_poll() checks the "wq->delta"
to free old WQEs:
if ((atomic_read(&wq->delta) + num_wqebbs) > wq->q_depth)
return ERR_PTR(-EBUSY);
There is a probability that the shadow WQE which hinic_xmit_frame() is
using will be damaged by copy_wqe_to_shadow():
if (curr_pg != end_pg) {
void *shadow_addr = &wq->shadow_wqe[curr_pg * wq->max_wqe_size];
copy_wqe_to_shadow(wq, shadow_addr, num_wqebbs, *cons_idx);
return shadow_addr;
}
This can cause WQE data error and you will see the above error messages.
This patch fixes the problem.
Signed-off-by: Zhao Chen <zhaochen6@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 114813 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 141440 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 1384500 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 1357414 ("Missing break in switch")
Addresses-Coverity-ID: 1357415 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 114811 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 1410181 ("Missing break in switch")
Addresses-Coverity-ID: 1410184 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 1384501 ("Missing break in switch")
Addresses-Coverity-ID: 1398869 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 1410182 ("Missing break in switch")
Addresses-Coverity-ID: 1410183 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Notice that in this particular case, I replaced the code comments with
a proper "fall through" annotation, which is what GCC is expecting
to find.
Addresses-Coverity-ID: 114809 ("Missing break in switch")
Addresses-Coverity-ID: 114810 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 114808 ("Missing break in switch")
Addresses-Coverity-ID: 114802 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 114796 ("Missing break in switch")
Addresses-Coverity-ID: 114804 ("Missing break in switch")
Addresses-Coverity-ID: 114806 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 114801 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 114800 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 114799 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 200521 ("Missing break in switch")
Addresses-Coverity-ID: 114797 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 114794 ("Missing break in switch")
Addresses-Coverity-ID: 114795 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 114792 ("Missing break in switch")
Addresses-Coverity-ID: 114793 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 114791 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 114790 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 114789 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 114788 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 114787 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 114784 ("Missing break in switch")
Addresses-Coverity-ID: 114785 ("Missing break in switch")
Addresses-Coverity-ID: 114786 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 114782 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 114781 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 114780 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 114777 ("Missing break in switch")
Addresses-Coverity-ID: 114778 ("Missing break in switch")
Addresses-Coverity-ID: 114779 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 114910 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 143135 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 114878 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 114891 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 114889 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for the Broadcom Omega SoC internal Combo Ethernet
GPHY to the bcm7xxx phy driver.
Signed-off-by: Arun Parameswaran <arun.parameswaran@broadcom.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for the Broadcom Omega SoC internal ethernet switch
to the b53 srab driver in the DSA framework.
Signed-off-by: Arun Parameswaran <arun.parameswaran@broadcom.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
40GbE Intel Wired LAN Driver Updates 2018-08-07
This series contains updates to i40e and i40evf only.
Sergey cleans up a duplicate call to i40e_prep_for_reset() during
shutdown.
YueHaibing cleans up i40evf by removing code that was never being used
or called within the driver.
Jake updates the ethtool statistics to use a helper function since many
of the statistics use the same basic logic for copying strings into the
supplied buffer. Cleaned up the use of a local variable that is no
longer needed or used. Fixed additional stats issues, including the
failure to update the data pointer which was causing stats to be
reported incorrectly.
Mariusz fixes a bug where there was an oversight in configuring FEC when
link settings were forced which was causing 25G link to be configured
incorrectly.
Piotr adds a missing return code for when the firmware returns a busy
state. Also added the process to command firmware to start
rearrangement when switching between old NVM structure to the new flat
NVM.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
RoCE qps use a pair of physical queues (pq) received from the Queue Manager
(QM) - an offload queue (OFLD) and a low latency queue (LLT). The QM block
creates a pq for each TC, and allows RoCE qps to ask for a pq with a
specific TC. As a result, qps with different VLAN priorities can be mapped
to different TCs, and employ features such as PFC and ETS.
Signed-off-by: Michal Kalderon <michal.kalderon@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: Denis Bolotin <denis.bolotin@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Distinguish not set offload_tc from offload_tc 0 and add getters and
setters.
Signed-off-by: Michal Kalderon <michal.kalderon@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: Denis Bolotin <denis.bolotin@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The API receives a priority and looks for the TC it is mapped to in the
operational DCBX configuration. The API returns QED_DCBX_DEFAULT_TC (0)
when DCBX is disabled.
Signed-off-by: Michal Kalderon <michal.kalderon@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: Denis Bolotin <denis.bolotin@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For packets with computed IP/TCP/UDP checksum there is no need to tell
hardware to recompute it. For such kind of packets hardware expects the
packet to be at least 64 bytes and FCS to be computed.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move checksum clearing outside of spinlock. The SKB is protected by
networking lock (HARD_TX_LOCK()).
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use netdev_tx_t return type for ndo_start_xmit function of macb driver.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Print a string instead of the error code. Since there is a
possibility that the driver can recover, classify it as a
warning instead of an error.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When backing device firmware reports an error, it provides an
error ID, which is meant to be queried for more detailed error
information. Currently, however, an error ID is not provided by
the Virtual I/O server and there are not any plans to do so. For
now, it is always unfilled or zero, so request_error_information
will never be called. Remove it.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All control commands (soft commands) goes through only Queue 0
(control and data queue). So only queue-0 needs post_lock,
other queues are only data queues and does not need post_lock
Added a flag to indicate the queue can be used for soft commands.
If this flag is set, post_lock must be acquired before posting
a command to the queue.
If this flag is clear, post_lock is invalid for the queue.
Signed-off-by: Intiyaz Basha <intiyaz.basha@cavium.com>
Signed-off-by: Felix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The allocation of lmac->dmacs is not being checked for allocation
failure. Add the check.
Fixes: 3a34ecfd9d ("net: thunderx: add MAC address filter tracking for LMAC")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Unlike fs.val.lport and fs.val.fport, cxgb4_process_flow_match()
sets fs.val.{l,f}ip to net-endian values without conversion - they come
straight from flow_dissector_key_ipv4_addrs ->dst and ->src resp. So
the assignment in mk_act_open_req() ought to be a straight copy.
As far as I know, T4 PCIe cards do exist, so it's not as if that
thing could only be found on little-endian systems...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Acked-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce a new layer for matching on geneve options. This allows
offloading filters configured to match geneve with options.
Signed-off-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce new push geneve option action. This allows offloading
filters configured to entunnel geneve with options.
Signed-off-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The addition of FLOW_DISSECTOR_KEY_ENC_IP to TC flower means that the ToS
and TTL of the tunnel header can now be matched on.
Extend the NFP tunnel match function to include these new fields.
Signed-off-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The TTL for encapsulating headers in IPv4 UDP tunnels is taken from a
route lookup. Modify this to first check if a user has specified a TTL to
be used in the TC action.
Signed-off-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This function accidentally failed to update the data pointer, which
caused the reported stats to be incorrect. Additionally, statistics
which follow queue stats in the output would potentially read non-zeroed
garbage data from the ethtool buffer.
This occurred because the data double pointer was not dereferenced
before incrementing the size.
Additionally, make sure this issue is more visible by adding a WARN_ONCE
to the i40e_get_ethtool_stats function. This warning will trigger
whenever the data pointer is not at the expected address, similar to the
check that we make in the i40e_get_stat_strings() function.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
During switching between old NVM structure approach (called structured
NVM) to new one (called flat NVM) or backward flash needs to be
rearranged to required NVM structure. This is a part of transition from
one NVM structure to another. The function is introduced to command
firmware to start rearrangement process.
Signed-off-by: Piotr Azarewicz <piotr.azarewicz@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Firmware can return a busy state, so the function return
I40E_ERR_NOT_READY.
Signed-off-by: Piotr Azarewicz <piotr.azarewicz@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In commit 147e81ec75 ("i40e: Test memory before ethtool alloc succeeds")
code was added to handle ring allocation on systems with low memory.
It shadowed the ring parameter pointer by introducing a local ring
pointer inside the for loop. Most of the code in the loop already just
accessed the ring via &rx_rings[i]. Since most of the code already does
this, just remove the local variable.
If someone considers it worth keeping a local around, they should use it
for the whole section instead of just a couple of accesses.
This fixes a warning when -Wshadow is enabled
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Commit c61c8fe1d5 ("i40e: Implement an ethtool private flag to stop
LLDP in FW") added an extra for-loop which added a shadowing 'i'
variable as the index.
However, the local variable i already exists, and we already use it as
a loop index. Additionally, at this point, there is no further use of
the variable, so it's safe to simply overwrite the variable contents.
This fixes a -Wshadow warning which has started being enabled on some
distributions
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Patryk Malek <patryk.malek@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The SYSTEMPORT MAC allows up to 8 filters to be programmed to wake-up
from LAN. Verify that we have up to 8 filters and program them to the
appropriate RXCHK entries to be matched (along with their masks).
We need to update the entry and exit to Wake-on-LAN mode to keep the
RXCHK engine running to match during suspend, but this is otherwise
fairly similar to Magic Packet detection.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow propagating ethtool::rxnfc programming to the CPU/management port
such that it is possible for such a CPU to perform e.g: Wake-on-LAN
using filters configured by the switch. We need a tiny bit of
cooperation between the switch drivers which is able to do the full flow
matching, whereas the CPU/management port might not. The CPU/management
driver needs to return -EOPNOTSUPP to indicate an non critical error,
any other error code otherwise.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann says:
====================
pull-request: bpf-next 2018-08-07
The following pull-request contains BPF updates for your *net-next* tree.
The main changes are:
1) Add cgroup local storage for BPF programs, which provides a fast
accessible memory for storing various per-cgroup data like number
of transmitted packets, etc, from Roman.
2) Support bpf_get_socket_cookie() BPF helper in several more program
types that have a full socket available, from Andrey.
3) Significantly improve the performance of perf events which are
reported from BPF offload. Also convert a couple of BPF AF_XDP
samples overto use libbpf, both from Jakub.
4) seg6local LWT provides the End.DT6 action, which allows to
decapsulate an outer IPv6 header containing a Segment Routing Header.
Adds this action now to the seg6local BPF interface, from Mathieu.
5) Do not mark dst register as unbounded in MOV64 instruction when
both src and dst register are the same, from Arthur.
6) Define u_smp_rmb() and u_smp_wmb() to their respective barrier
instructions on arm64 for the AF_XDP sample code, from Brian.
7) Convert the tcp_client.py and tcp_server.py BPF selftest scripts
over from Python 2 to Python 3, from Jeremy.
8) Enable BTF build flags to the BPF sample code Makefile, from Taeung.
9) Remove an unnecessary rcu_read_lock() in run_lwt_bpf(), from Taehee.
10) Several improvements to the README.rst from the BPF documentation
to make it more consistent with RST format, from Tobin.
11) Replace all occurrences of strerror() by calls to strerror_r()
in libbpf and fix a FORTIFY_SOURCE build error along with it,
from Thomas.
12) Fix a bug in bpftool's get_btf() function to correctly propagate
an error via PTR_ERR(), from Yue.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the following sparse warning about mismatch rcu
attribute for address space annotation:
...
error: incompatible types in comparison expression (different modifiers)
error: incompatible types in comparison expression (different address spaces)
...
Some __rcu annotation was at non-pointers list head structures and one was
missing in edge information which is used by rcu_assign_pointer() to
update edge setting information.
Cc: Stefan Schmidt <stefan@datenfreihafen.org>
Fixes: f25da51fdc ("ieee802154: hwsim: add replacement for fakelb")
Signed-off-by: Alexander Aring <aring@mojatatu.com>
Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The priority flow control statistics are laid out in the stats structure
using arrays. This made it unwieldy to use as part of an i40e_stats
array.
Add a new structure type, i40e_pfc_stats, and a helper function
i40e_get_pfc_stats which can return the stats for a given priority
value as an i40e_pfc_stats structure.
Use this to create an i40e_stats array, which we'll use to format and
copy the strings and stats into the supplied buffers.
This reduces even more boiler plate code in i40e_get_ethtool_stats and
i40e_get_stat_strings.
An alternative would be to modify the structure definition for the pfc
stats, but this is more invasive to the rest of the code base.
Note that a macro was used to setup the copy of stats from the
pf->stats, as this reduces the chance of typos in the code names. It
will produce a checkpatch.pl warning due to re-use of a macro argument.
In this case, it should be safe, as the macro will fail to compile in
cases where the argument is not a simple structure member name, and thus
arguments with side effects should not be an issue.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The VEB TC stats are currently implemented with separate parsing,
instead of using the i40e_stats array and associated helper functions.
This is likely because the stats rely on embedding the TC number into
the stat name.
Update i40e_add_stat_strings to take variadic arguments, and use these
to vsnprintf the i40e_stats string as a string containing format
specifiers.
Create a stats array for the VEB TC related stats,
i40e_gstrings_veb_tc_stats, and use this along with the helper functions
to remove the specialized boiler plate code.
Always call i40e_add_ethtool_stats for both this array and the general
VEB stats array. This ensures that we zero out any memory in case it was
not zero-allocated for us.
This ultimately results in less boiler plate code for the
i40e_get_stat_strings and i40e_get_ethtool_stats.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch configures FEC setting in i40e_force_link_state().
For some reason setting this field was overlooked thus causing
25G link to be configured incorrectly.
Signed-off-by: Mariusz Stachura <mariusz.stachura@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Similar to the helper function to copy the ethtool stats strings, add
and use a helper function for copying the ethtool stats into the
supplied buffer.
Just like before, we use a macro to avoid having to pass ARRAY_SIZE
manually, so as to reduce chance of bugs.
Some of the stats, especially queue stats, are a bit trickier, and will
be handled in future patches.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Many of the ethtool statistics use the same basic logic for copying
strings into the supplied buffer. A set of stats are stored in a const
array of i40e_stats structures, and we apply these all together.
Simplify the stats code by introducing a helper function which can take
a stats array and copy the strings into the buffer, updating the buffer
pointer as we go.
We use a macro to implement i40e_add_stat_strings so that ARRAY_SIZE can
be used on the array passed in. This ensures that we always use the
matching size in __i40e_add_stat_strings.
More complex stats currently do not use i40e_stats arrays, usually due
to custom formatted strings, or because the stats are not laid out in
the expected way. These stats will be updated to use the helper function
in separate future patches.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There are no in-tree callers.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Function call to i40e_prep_for_reset() is duplicated in
i40e_shutdown routine and gets called before
i40e_enable_mc_magic_wake() which blocks it from being executed
correctly on system reboot or shutdown because adminq is already
disabled by first i40e_prep_for_reset() call.
Two register write calls are also duplicated.
Signed-off-by: Sergey Nemov <sergey.nemov@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Stefan Schmidt says:
====================
pull-request: ieee802154-next 2018-08-06
An update from ieee802154 for *net-next*
Romuald added a socket option to get the LQI value of the received datagram.
Alexander added a new hardware simulation driver modelled after hwsim of the
wireless people. It allows runtime configuration for new nodes and edges over a
netlink interface (a config utlity is making its way into wpan-tools).
We also have three fixes in here. One from Colin which is more of a cleanup and
two from Alex fixing tailroom and single frame space problems.
I would normally put the last two into my fixes tree, but given we are already
in -rc8 I simply put them here and added a cc: stable to them.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This part of the iwlwifi driver doesn't need anything provided by
pci-aspm.h, so remove the unnecessary include of it.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Sinan Kaya <okaya@kernel.org>
Acked-by: Luca Coelho <luciano.coelho@intel.com>
The ath9k driver doesn't need anything provided by pci-aspm.h, so remove
the unnecessary include of it.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Sinan Kaya <okaya@kernel.org>
Acked-by: Kalle Valo <kvalo@codeaurora.org>
The igb driver doesn't need anything provided by pci-aspm.h, so remove
the unnecessary include of it.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Sinan Kaya <okaya@kernel.org>
Acked-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
__inet6_lookup_established() expect th->dport passed in host-endian,
not net-endian. The reason is microoptimization in __inet6_lookup(),
but if you use the lower-level helpers, you have to play by their
rules...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
ath.git patches for 4.19. Major changes:
ath10k
* add debugfs file warm_hw_reset
wil6210
* add debugfs files tx_latency, link_stats and link_stats_global
* add 3-MSI support
* allow scan on AP interface
* support max aggregation window size 64
Since mac802154_hwsim the fakelb driver will get deprecated. This patch will
notifier all users of fakelb to switch to the new mac802154_hwsim driver.
Signed-off-by: Alexander Aring <aring@mojatatu.com>
Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
This patch adds a new virtual driver mac802154_hwsim which is based on
the fakelb driver.
The fakelb driver will get deprecated and hopefully removed someday.
The main reason for doing this step is to rename the driver to
mac802154_hwsim to have a similar naming scheme as mac80211_hwsim,
which is more popular in the 802.11 wireless word and the idea is the
same behind this driver.
The new features of this driver are to have knowledge about connected
edges, which can be changed during runtime. This offers a testing
environment for routing protocols e.g. RPL.
The default behaviour is still as fakelb: two radios connected to each
other. New added radios during runtime will not be connected to other
wpan_hwsim instances.
The netlink api is not namespace aware on purpose, only the registered
wpan_phy's can be moved to namespaces. The physical layer according to
wiresless "air" communication can be handled across namespaces.
Furthermore the edges can be weighted with the LQI value according IEEE
802.15.4 which offers additional handling to mark bad or good connection
indicators to other connected virtual phys.
Signed-off-by: Alexander Aring <aring@mojatatu.com>
Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
This time a bigger pull request as we have two new Mediatek drivers
MT76x2u (CONFIG_MT76x2U) and MT76x0U (CONFIG_MT76x0U). Also iwlwifi got
support for the new IEEE 802.11ax standard, the successor for
802.11ac. And naturally smaller new features and bugfixes all over.
Major changes:
wcn36xx
* fix WEP in client mode
wil6210
* add support for Talyn-MB (Talyn ver 2.0) device
* add support for enhanced DMA firmware feature
iwlwifi
* implement 802.11ax D2.0
* support for the new 22560 device family
* new PCI IDs for 22000 and 22560
qtnfmac
* implement cfg80211 power management callback
* enable multiple SSIDs scan support
* qtnfmac: implement basic WoWLAN support
mt7601u
* fall back to software encryption for hw unsupported ciphers
* enable 802.11 Management Frame Protection (MFP)
mt76
* support setting RTS threshold
* add USB support
* add support for MT76x2u devices
* add support for MT76x0U devices
mwifiex
* allow user space to set all other IEs except WMM IE
rsi
* add firmware support for AP+BT dual mode
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJbZyxDAAoJEG4XJFUm622bq2AH/2yJAeOKb7Z25ezsvldaEDd3
cYS4TjLevXacDU5NdINtm1IRMct1ZldwUjrjgR2I/eLaSHhxyIdV4hb05etSN8qZ
yo86aa1gs+8rSEn/GVO8UjX8Bh4NM/tff+yzMKWiWJGe9DtBvswSUPxBOU91vS8K
WcCpvWh9SpmAPyZEDWsZnTK7AUc+X2T+Soit+pJmLm9P3RxkvMqQxG82eMGVnooO
5aNe0T9zYLB4aB8unCJqPSYSLVDJ55vnC8tFIjcEhNCF/745gyMD/CrcQ4zCxdN/
KF6WEDc/XePF5qrHvkzWA7HiR0Xs9pDt3KugkU0enZV+cba0kKaBq230sZ++1KM=
=BwxN
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2018-08-05' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 4.19
This time a bigger pull request as we have two new Mediatek drivers
MT76x2u (CONFIG_MT76x2U) and MT76x0U (CONFIG_MT76x0U). Also iwlwifi got
support for the new IEEE 802.11ax standard, the successor for
802.11ac. And naturally smaller new features and bugfixes all over.
Major changes:
wcn36xx
* fix WEP in client mode
wil6210
* add support for Talyn-MB (Talyn ver 2.0) device
* add support for enhanced DMA firmware feature
iwlwifi
* implement 802.11ax D2.0
* support for the new 22560 device family
* new PCI IDs for 22000 and 22560
qtnfmac
* implement cfg80211 power management callback
* enable multiple SSIDs scan support
* qtnfmac: implement basic WoWLAN support
mt7601u
* fall back to software encryption for hw unsupported ciphers
* enable 802.11 Management Frame Protection (MFP)
mt76
* support setting RTS threshold
* add USB support
* add support for MT76x2u devices
* add support for MT76x0U devices
mwifiex
* allow user space to set all other IEs except WMM IE
rsi
* add firmware support for AP+BT dual mode
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to give unicast traffic precedence over BUM traffic, configure
multicast-aware mode on all ports.
Under multicast-aware regime, when assigning traffic class to a packet,
the switch doesn't merely take the value prescribed by the QTCT
register. For BUM traffic, it instead assigns that value plus 8.
ETS elements for TCs 8..15 thus need to be configured as well. Extend
mlxsw_sp_port_ets_init() so that it maps each of them to the same
subgroup as their corresponding TC from the range 0..7, such that TCs X
and X+8 map to the same subgroup.
The existing code configures TCs with strict priority. So far this was
immaterial, because each TC had its own subgroup. Now that two TCs share
a subgroup it becomes important. TCs are prioritized in order of 7, 6,
..., 0, 15, 14, ..., 8: the higher TCs used for BUM traffic end up being
deprioritized. Since that's what's needed, keep that configuration as it
is, and configure the new TCs likewise.
Finally in mlxsw_sp_port_create(), invoke configuration of QTCTM to
enable MC-aware mode on each port.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This register configures if the Switch Priority to Traffic Class mapping
is based on Multicast packet indication. If so, then multicast packets
will get a Traffic Class that is plus (cap_max_tclass_data/2) the value
configured by QTCT.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 1402059 ("Missing break in switch")
Addresses-Coverity-ID: 1402060 ("Missing break in switch")
Addresses-Coverity-ID: 1402061 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The CNP CoS queue is reserved for internal RDMA Congestion Notification
Packets (CNP) and should not be used for a TC. Modify the CoS queue
discovery code to skip over the CNP CoS queue and to reduce
bp->max_tc accordingly. However, if RDMA is disabled in NVRAM, the
the CNP CoS queue can be used for a TC.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Expand the .ieee_setapp() and ieee_delapp() DCBNL methods to support
DSCP. This allows DSCP values to user priority mappings instead
of using VLAN priorities. Each DSCP mapping is added or deleted one
entry at a time using the firmware API. The firmware call can only be
made from a PF.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Export temperature sensor reading via hwmon sysfs.
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use latest firmware API to notify firmware about IF state changes.
Firmware has the option to clean up resources during IF down and
to require the driver to reserve resources again during IF up.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The flags field is almost getting full. Move firmware capability flags
to a new fw_cap field to better organize these firmware flags.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The BNXT_FLAG_NEW_RM flag is checked a lot in the code to determine if
the new resource manager is in effect. Define a macro to perform
this check.
Signed-off-by: Michael Chan <michael.chan@broadocm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support to collect live firmware coredump via ethtool.
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set the default hash mode flag in HWRM_VNIC_RSS_CFG to signal to the
firmware that the driver is compliant with the latest spec. With
that, the firmware can return expanded RSS profile IDs that the driver
checks to setup the proper gso_type for GRO-HW packets. But instead
of checking for the new profile IDs, we check the IP_TYPE flag
in TPA_START which is more straight forward than checking a list of
profile IDs.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The new mode is "minimal-static" to be used when resources are more
limited to support a large number of VFs, for example The PF driver
will provision guaranteed minimum resources of 0. Each VF has no
guranteed resources until it tries to reserve resources during device
open.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During hotplug, the driver's open function can be called almost
immediately after power on reset. The PHY may not be ready and the
firmware may return failure when the driver tries to update PHY
settings. Add retry logic fired from the driver's timer to retry
the operation for 5 seconds.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add code to detect firmware support for external loopback and the extra
test entry for external loopback.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver gathers statistics using 2 mechanisms. Some stats are DMA'ed
directly from hardware and others are polled from the driver's timer.
Currently, we only adjust the DMA frequency based on the ethtool
stats-block-usecs setting. This patch adjusts the driver's timer
frequency as well to make everything consistent.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
New interface has firmware core dump support, new extended port
statistics, and IF state change notifications to the firmware.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We use ARRAY_SIZE to replace open code sizeof(lan78xx_regs) / sizeof(u32).
It make the code concise.
Signed-off-by: zhong jiang <zhongjiang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
0x3ff in tun_hashfn is mask of TUN_NUM_FLOW_ENTRIES, instead
of hardcode, define a macro to setup the relationship with
TUN_NUM_FLOW_ENTRIES
Signed-off-by: Li RongQing <lirongqing@baidu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
vnic_dev_register(), vnic_rq_alloc_bufs() and vnic_wq_alloc_bufs()
are never called in atomic context.
They call kzalloc() with GFP_ATOMIC, which is not necessary.
GFP_ATOMIC can be replaced with GFP_KERNEL.
This is found by a static analysis tool named DCNS written by myself.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Acked-by: Govindarajulu Varadarajan <gvaradar@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for adjust_tail. There are no FW changes needed but add
a FW capability just in case there would be any issue with previously
released FW, or we will have to change the ABI in the future.
The helper is trivial and shouldn't be used too often so just inline
the body of the function. We add the delta to locally maintained
packet length register and check for overflow, since add of negative
value must overflow if result is positive. Note that if delta of 0
would be allowed in the kernel this trick stops working and we need
one more instruction to compare lengths before and after the change.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Rename trace symbols that conflict with mt7601u and remove some
definitions that are not used.
Patch fixes build errors like this:
ld: drivers/net/wireless/mediatek/mt76/mt76x0/trace.o:(__tracepoints+0x0): multiple definition of `__tracepoint_set_shared_key'; drivers/net/wireless/mediatek/mt7601u/trace.o:(__tracepoints+0x0): first defined here
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Fixes: 7b4859026c ("mt76x0: core files")
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
mt76_* functions conflicts with mt7601u driver what prevents to build
those drivers in the kernel or use both drivers modules at once.
Patch fixes build errors like this:
ld: drivers/net/wireless/mediatek/mt76/mt76x0/mac.o:(.opd+0x30): multiple definition of `mt76_mac_tx_rate_val'; drivers/net/wireless/mediatek/mt7601u/mac.o:(.opd+0x30): first defined here
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Fixes: 7b4859026c ("mt76x0: core files")
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In the quest to remove all stack VLA usage from the kernel[1], this
removes the discouraged use of AHASH_REQUEST_ON_STACK (and associated
VLA) by switching to shash directly and keeping the associated descriptor
allocated with the regular state on the heap.
[1] https://lkml.kernel.org/r/CA+55aFzCG-zNmZwX4A2FQpadafLfEzK6CC=qPXydAacU1RqZWA@mail.gmail.com
Signed-off-by: Kees Cook <keescook@chromium.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
In previous patch mlxsw_afa_resource_del() was added to avoid a duplicate
resource detruction scenario.
For mirror actions, such duplicate destruction leads to a crash as in:
# tc qdisc add dev swp49 ingress
# tc filter add dev swp49 parent ffff: \
protocol ip chain 100 pref 10 \
flower skip_sw dst_ip 192.168.101.1 action drop
# tc filter add dev swp49 parent ffff: \
protocol ip pref 10 \
flower skip_sw dst_ip 192.168.101.1 action goto chain 100 \
action mirred egress mirror dev swp4
Therefore add a call to mlxsw_afa_resource_del() in
mlxsw_afa_mirror_destroy() in order to clear that resource
from rule's resources.
Fixes: d0d13c1858 ("mlxsw: spectrum_acl: Add support for mirror action")
Signed-off-by: Nir Dotan <nird@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Each tc flower rule uses a hidden count action. As counter resource may
not be available due to limited HW resources, update _counter_create()
and _counter_destroy() pair to follow previously introduced symmetric
error condition handling, add a call to mlxsw_afa_resource_del() as part
of the counter resource destruction.
Fixes: c18c1e186b ("mlxsw: core: Make counter index allocated inside the action append")
Signed-off-by: Nir Dotan <nird@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some ACL actions require the allocation of a separate resource
prior to applying the action itself. When facing an error condition
during the setup phase of the action, resource should be destroyed.
For such actions the destruction was done twice which is dangerous
and lead to a potential crash.
The destruction took place first upon error on action setup phase
and then as the rule was destroyed.
The following sequence generated a crash:
# tc qdisc add dev swp49 ingress
# tc filter add dev swp49 parent ffff: \
protocol ip chain 100 pref 10 \
flower skip_sw dst_ip 192.168.101.1 action drop
# tc filter add dev swp49 parent ffff: \
protocol ip pref 10 \
flower skip_sw dst_ip 192.168.101.1 action goto chain 100 \
action mirred egress mirror dev swp4
Therefore add mlxsw_afa_resource_del() as a complement of
mlxsw_afa_resource_add() to add symmetry to resource_list membership
handling. Call this from mlxsw_afa_fwd_entry_ref_destroy() to make the
_fwd_entry_ref_create() and _fwd_entry_ref_destroy() pair of calls a
NOP.
Fixes: 140ce42121 ("mlxsw: core: Convert fwd_entry_ref list to be generic per-block resource list")
Signed-off-by: Nir Dotan <nird@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Spectrum switch ACL action set is built in groups of three actions
which may point to additional actions. A group holds a single record
which can be set as goto record for pointing at a following group
or can be set to mark the termination of the lookup. This is perfectly
adequate for handling a series of actions to be executed on a packet.
While the SW model allows configuration of conflicting actions
where it is clear that some actions will never execute, the mlxsw
driver must block such configurations as it creates a conflict
over the single terminate/goto record value.
For a conflicting actions configuration such as:
# tc filter add dev swp49 parent ffff: \
protocol ip pref 10 \
flower skip_sw dst_ip 192.168.101.1 \
action goto chain 100 \
action mirred egress mirror dev swp4
Where it is clear that the last action will never execute, the
mlxsw driver was issuing a warning instead of returning an error.
Therefore replace that warning with an error for this specific
case.
Fixes: 4cda7d8d70 ("mlxsw: core: Introduce flexible actions support")
Signed-off-by: Nir Dotan <nird@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Create a helper function to turn on/off MPD, this will be used to avoid
duplicating code as we are going to add additional types of wake-up
types.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
We already properly resume from Wake-on-LAN whether such a condition
occured or not, no need to process the WoL interrupt for functional
changes since that could race with other settings.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When we are in Wake-on-LAN, we operate with the host sofware not running
a network stack, so we want to the switch to flood packets in order to
cause a system wake-up when matching specific filters (unicast or
multicast). This was not necessary before since we supported Magic
Packet which are targeting a broadcast MAC address which the switch
already floods.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
ds->enabled_port_mask only contains a bitmask of user-facing enabled
ports, we also need to allow programming CFP rules that target CPU ports
(e.g: ports 5 and 8).
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The offset of msix number for roce is different between different
revision id. We should get it from firmware, instead of a fix value.
This patch refines the msix allocation, make it compatible.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The msix number for vf is different, depends on the max vf number.
Futherly if the vf supports roce, the offset of msix is not fixed.
It's incorrect to fix the msix number to 33. This patch fixes it by
querying the msix number from firmware, and adjusting it with roce
support.
Fixes: e2cb1dec97 ("net: hns3: Add HNS3 VF HCL(Hardware Compatibility Layer) Support")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The else-if branch and else branch set mac_ok to true similarly,
so combine the two into single else branch.
Also add comments to explain the two conditions, which
from Michael Chan and Vasundhara Volam.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that the unregister_netdev flow for IPoIB no longer relies on external
code we can now introduce the use of priv_destructor and
needs_free_netdev.
The rdma_netdev flow is switched to use the netdev common priv_destructor
instead of the special free_rdma_netdev and the IPOIB ULP adjusted:
- priv_destructor needs to switch to point to the ULP's destructor
which will then call the rdma_ndev's in the right order
- We need to be careful around the error unwind of register_netdev
as it sometimes calls priv_destructor on failure
- ULPs need to use ndo_init/uninit to ensure proper ordering
of failures around register_netdev
Switching to priv_destructor is a necessary pre-requisite to using
the rtnl new_link mechanism.
The VNIC user for rdma_netdev should also be revised, but that is left for
another patch.
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Denis Drozdov <denisd@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Return statements in functions returning bool should use true or false
instead of an integer value.
This issue was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Wei Liu <wei.liu2@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current value for a target abort error is 0x010, however, this value
should in fact be 0x002. As it stands, the range of error is 0..7 so
it is currently never being detected. This bug has been in the driver
since the early 2.6.12 days (or before).
Detected by CoverityScan, CID#744290 ("Logically dead code")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Variables 'max_frm' and 'tmp_mac_key' are being assigned,
but are never used,hence they are redundant and can be removed.
fix fllowing warning:
drivers/net/ethernet/hisilicon/hns/hns_dsaf_mac.c:461:6: warning: variable 'max_frm' set but not used [-Wunused-but-set-variable]
drivers/net/ethernet/hisilicon/hns/hns_dsaf_main.c:1685:31: warning: variable 'tmp_mac_key' set but not used [-Wunused-but-set-variable]
drivers/net/ethernet/hisilicon/hns/hns_dsaf_main.c:1855:41: warning: variable 'tmp_mac_key' set but not used [-Wunused-but-set-variable]
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for suspend and resume to the Broadcom iProc mdio
mux driver.
Signed-off-by: Arun Parameswaran <arun.parameswaran@broadcom.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support to configure the internal rate adjust register based on the
core clock supplied through device tree in the Broadcom iProc mdio mux.
The operating frequency of the mdio mux block is 11MHz. This is derrived
by dividing the clock to the mdio mux with the rate adjust register.
In some SoC's the default values of the rate adjust register do not yield
11MHz. These SoC's are required to specify the clock via the device tree
for proper operation.
Signed-off-by: Arun Parameswaran <arun.parameswaran@broadcom.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use devm_mdiobus_alloc() instead of mdiobus_alloc() in the Broadcom
iProc mdio mux driver.
Signed-off-by: Arun Parameswaran <arun.parameswaran@broadcom.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Configure the scan control register in the Broadcom iProc
mdio mux driver to disable access to external master.
In some SoC's, the scan control register defaults to an incorrect
value.
Signed-off-by: Arun Parameswaran <arun.parameswaran@broadcom.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Modify the register offsets in the Broadcom iProc mdio mux to start
from the top of the register address space.
Earlier, the base address pointed to the end of the block's register
space. The base address will now point to the start of the mdio's
address space. The offsets have been fixed to match this.
Signed-off-by: Arun Parameswaran <arun.parameswaran@broadcom.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch implements basic WoWLAN support in qtnfmac driver, including
processing of WoWLAN features reported by firmware and implementation
of cfg80211 suspend/resume/wakeup callbacks. Currently the following
WoWLAN triggers are supported: disconnect, magic packet,
custom pattern packet.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Firmware blob will be located in mediatek subdirectory. Add "u" suffix
to indicate this is USB device firmware.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Disable HW before probe, otherwise after reboot we will fail
to initialize MCU.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add Kconfig and Makefiles for mt76x0 driver. Now the driver
can be build.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Core files of mt76x0 driver.
mt76x0 driver adds support for Mediatek MT7610U based
USB Wi-Fi dongles.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
MT76x2u is a 2x2 USB 802.11ac chipset by MediaTek. This driver currently
support station mode
Tested-by: <cug_yangyuancong@hotmail.com>
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This will be used by drivers for MT76x2u based devices
Tested-by: <cug_yangyuancong@hotmail.com>
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Move mt76x2_debugfs code in mt76-common module since it is shared
between mt76x2 and mt76x2u
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Move phy related code shared between mt76x2 and mt76x2u in
mt76x2-common module
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Move core related code shared between mt76x2 and mt76x2u in
mt76x2-common module
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Move init related code shared between mt76x2 and mt76x2u in
mt76x2-common module
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Move mac related code shared between mt76x2 and mt76x2u in
mt76x2-common module
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Move tx related code shared between mt76x2 and mt76x2u in mt76x2-common
module
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In order to remove usb dependency from pcie code, add mt76x2-common as
a container of shared code between mt76x2 and mt76x2u. Add eeprom code
to mt76x2-common module
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add tx_queue_skb function pointer in mt76_bus_ops since mt76x2u based
devices do not map mt76x2_txwi on dma buffers and it is not possible
to reuse mt76_dma_tx_queue_skb() routine to enqueue tx frames to
hw buffers
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Move mt76_dma_tx_queue_skb routine in dma.c.
Remove static qualifier from mt76_get_txwi definition
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add frame length to mt76x2_mac_write_txwi routine signature and do not
fetch it from skb since txwi data structure is added at the beginning of
the skb for usb based devices and mt76x2_mac_write_txwi will be shared
between pci and usb related code
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
in order to reuse mt76_rx_complete routine supporting mt76x2u based
devices add napi struct to mt76_rx_poll_complete and mt76_rx_complete
routine signatures and do not fetch it according to the rx queue index
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add mt76x2_mac_load_tx_status routine since tx stats register map is
shared between usb and pci based devices but usb devices do not have a
tx stat irq line as pcie ones and it is necessary to load tx statistics
using a workqueue
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Move wiphy interface_modes definition in mt76x2_init in order to
reuse mt76_register_device routine supporting mt76x2u based chipsets
since mt76x2u currently supports just sta mode
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add mt76x2_init_device routine in order to reuse common pcie/usb mac80211
initialization code supporting mt76x2u based device
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In order to reuse them supporting mt76x2u based devices, move
mt76x2_wait_for_mac, wait_for_wpdma and mt76x2_channel_silent in
mt76x2.h
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
move mt76x2_fw_header and mt76x2_patch_header definitions in mcu.h in
order to reuse them in mt76x2u mcu related code
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Since MT_TXD_INFO, MT_MCU_MSG and MT_RX_FCE_INFO definitions are in
common between mt76x2u, mt76x2 and mt76x0u move them in dma.h in order
to reuse usb code supporting mt76x2u and mt76x0u based devices
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The BTF conflicts were simple overlapping changes.
The virtio_net conflict was an overlap of a fix of statistics counter,
happening alongisde a move over to a bonafide statistics structure
rather than counting value on the stack.
Signed-off-by: David S. Miller <davem@davemloft.net>
Trivial fix to spelling mistake in dev_info message.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Check DMA addressing limitations as suggested by the DMA API
how-to. This does not fix a particular issue seen but is
considered good style.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Acked-by: Fugang Duan <fugang.duan@nxp.com>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The code is different enough to justify a split.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We would like to allow other utlities to init msix and rx.
Put their declarations in a place accessible to other utilities.
Signed-off-by: Golan Ben Ami <golan.ben.ami@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
If CONFIG_IPV6 is not enabled in the kernel, tcp.h is not included
implicitly from other header files, causing compilation errors. To
solve that, explicitly include it in tx-gen2.c.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
There was a bunch of code to support gscan which has never been used.
Remove it all to cleanup and get rid of a lot of dead code.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Balanced power save mode isn't supported in the fw for 22560 devices
yet. Configure the power save mode to CAM until it gets implemented.
Signed-off-by: Golan Ben Ami <golan.ben.ami@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This reverts commit f2e66c8df0.
The firmware never implemented this, and they do not plan to.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The periphery can't be accessed before we set the
INIT_DONE bit which initializes the device.
A previous patch added a reconfiguration of the MSI-X
tables upon resume, but at that point in the flow,
INIT_DONE wasn't set. Since the reconfiguration of the
MSI-X tables require periphery access, it failed.
The difference between WoWLAN and without WoWLAN is that
in WoWLAN, iwl_trans_pcie_d3_suspend clears the INIT_DONE
without clearing the STATUS_DEVICE_ENABLED bit in the
software status. Because of that, the resume code thinks
that the device is enabled, but the INIT_DONE bit has been
cleared.
To fix this, don't reconfigure the MSI-X tables in case
WoWLAN is enabled. It will be done in
iwl_trans_pcie_d3_resume anyway.
Fixes: 52848a79b9 ("iwlwifi: pcie: reconfigure MSI-X HW on resume")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Currently multi-queue is disabled for 22000 devices.
This was since driver isn't supposed to write to prph
registers anymore, and FW needs to configure the RFH.
Now that FW added support for the API - use it and remove
the 22000 multi RX queue disablement.
Bump min API version to avoid compatibility issues.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Currently the firmware does not stop recording debugging data when
entering D3 and this causes trouble (e.g. sporadic wake ups).
Fix that by stopping dbg recording when suspending.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Reading and dumping memory areas takes time, and sometimes
dumping all of the areas isn't necessary.
Allow choosing the memory areas which should be dumped.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Golan Ben Ami <golan.ben.ami@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Op mode will need this data in order to feed FW with it.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This makes code less indented and more readable.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This allows less "dummy" declarations and casting.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
22560 devices use a new rx_mpdu_desc api.
Update the code to use the new api.
Signed-off-by: Golan Ben Ami <golan.ben.ami@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The rfh for 22560 devices has changed so it supports now
the same arch of using used and free lists, but different
structures to support the last.
Use the new structures, hw dependent, to manage the lists.
bd, the free list, uses the iwl_rx_transfer_desc,
in which the vid is stored in the structs' rbid
field, and the page address in the addr field.
used_bd, the used list, uses the iwl_rx_completion_desc
struct, in which the vid is stored in the structs' rbid
field.
rb_stts, the hw "write" pointer of rx is stored in a
__le16 array, in which each entry represents the write
pointer per queue.
Signed-off-by: Golan Ben Ami <golan.ben.ami@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
For FW_PORT_ACTION_GET_PORT_INFO32 messages, the
u.info32.lstatus32_to_cbllen32 is 32-bit Big Endian.
We need to translate that to CPU Endian in order to
test F_FW_PORT_CMD_DCBXDIS32.
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While cleaning the command queue, the value of the HEAD register is not
in the range of next_to_clean and next_to_use, meaning that this value
is invalid. This also means that there is a hardware error and the
hardware will trigger a reset soon. At this time we should return an
error code instead of 0, and HCLGE_STATE_CMD_DISABLE needs to be set to
prevent sending command again.
Fixes: 3ff504908f ("net: hns3: fix a dead loop in hclge_cmd_csq_clean")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This sysctl setting controls whether packet priority should be updated
after forwarding. Configure RGCR.usp accordingly so that the device is
in sync with the kernel handling.
Note that RGCR doesn't allow changing arbitrary parameters
mid-operation, however "usp" is exempt and can be reconfigured.
Also react to NETEVENT_IPV4_FWD_UPDATE_PRIORITY_UPDATE notifications
that signify change in this configuration.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The boilerplate to schedule NETEVENT_IPV4_MPATH_HASH_UPDATE and
NETEVENT_IPV6_MPATH_HASH_UPDATE handling is almost equivalent to that of
NETEVENT_IPV4_FWD_UPDATE_PRIORITY_UPDATE that's coming in the next
patch. The only difference is which actual worker function should be
called. Extract this boilerplate into a named function in order to allow
reuse.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Neterion was standalone for several years, then acquired by Exar and
shutdown in 11 months without ever making any new Exar branded adapters.
Users would probably think of them as Neterion and not Exar (as there
have been no follow-on adapters and the vast majority ever sold were
under the Neterion name).
6c541b4595 ("net: ethernet: Sort Kconfig sourcing alphabetically")
sorted Kconfig sourcing based on directory names, but in a couple cases,
the menu item text is quite different from the directory name and is not
sorted correctly:
drivers/net/ethernet/neterion/Kconfig => "Exar devices"
To address that and clear up any confusion about the name, "Exar" was
changed to "Neterion (Exar)" and the relevant entries in the Makefile
and Kconfig were reordered to match the alphabetical organization.
Inspired-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch handles a TX-timeout as follows:
1) This patch gathers and prints the following info that can
help in diagnosing the cause of a TX-timeout.
a) TX queue and completion queue entries.
b) SKB and TCP/UDP header details.
2) For Lancer NICs (TX-timeout recovery is not supported for
BE3/Skyhawk-R NICs), it recovers from the TX timeout as follows:
a) On a TX-timeout, driver sets the PHYSDEV_CONTROL_FW_RESET_MASK
bit in the PHYSDEV_CONTROL register. Lancer firmware goes into
an error state and indicates this back to the driver via a bit
in a doorbell register.
b) Driver detects this and calls be_err_recover(). DMA is disabled,
all pending TX skbs are unmapped and freed (be_close()). All rings
are destroyed (be_clear()).
c) The driver waits for the FW to re-initialize and re-creates all
rings along with other data structs (be_resume())
Signed-off-by: Suresh Reddy <suresh.reddy@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a potential execution path in which variable *err* is returned
without being properly initialized previously.
Fix this by initializing variable *err* to 0.
Addresses-Coverity-ID: 1472116 ("Uninitialized scalar variable")
Fixes: 0ec13877ce ("net/mlx5e: Gather all XDP pre-requisite checks in a single function")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Acked-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes the following sparse warning:
drivers/net/ethernet/qlogic/qed/qed_cxt.c:1534:6: warning: symbol 'qed_cm_init_pf' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_dev.c:233:4: warning: symbol 'qed_init_qm_get_num_tcs' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_dev.c:238:5: warning: symbol 'qed_init_qm_get_num_vfs' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_dev.c:246:5: warning: symbol 'qed_init_qm_get_num_pf_rls' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_dev.c:264:5: warning: symbol 'qed_init_qm_get_num_vports' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_dev.c:276:5: warning: symbol 'qed_init_qm_get_num_pqs' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_mcp.c:573:5: warning: symbol 'qed_mcp_nvm_wr_cmd' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_mcp.c:3012:1: warning: symbol '__qed_mcp_resc_lock' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_dcbx.c:870:6: warning: symbol 'qed_dcbx_aen' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_debug.c:7841:5: warning: symbol 'qed_dbg_nvm_image_length' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_debug.c:7857:5: warning: symbol 'qed_dbg_nvm_image' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_sriov.c:675:6: warning: symbol '_qed_iov_pf_sanity_check' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_sriov.c:690:6: warning: symbol 'qed_iov_pf_sanity_check' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_sriov.c:3982:6: warning: symbol 'qed_iov_pf_get_pending_events' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_vf.c:172:5: warning: symbol '_qed_vf_pf_release' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_rdma.c:137:5: warning: symbol 'qed_rdma_get_sb_id' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_rdma.c:709:5: warning: symbol 'qed_rdma_stop' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_ll2.c:161:6: warning: symbol 'qed_ll2b_complete_rx_packet' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_roce.c:160:6: warning: symbol 'qed_roce_free_cid_pair' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_iwarp.c:380:12: warning: symbol 'iwarp_state_names' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_iwarp.c:946:1: warning: symbol 'qed_iwarp_parse_private_data' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_iwarp.c:971:1: warning: symbol 'qed_iwarp_mpa_reply_arrived' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_iwarp.c:2504:1: warning: symbol 'qed_iwarp_ll2_slowpath' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_iwarp.c:2806:6: warning: symbol 'qed_iwarp_qp_in_error' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_iwarp.c:2827:6: warning: symbol 'qed_iwarp_exception_received' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_iwarp.c:2958:1: warning: symbol 'qed_iwarp_connect_complete' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_iscsi.c:876:6: warning: symbol 'qed_iscsi_free_connection' was not declared. Should it be static?
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Denis Bolotin <Denis.Bolotin@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
WoL won't work in PCI-based setups because we are not saving the PCI EP
state before entering suspend state and not allowing D3 wake.
Fix this by using a wrapper around stmmac_{suspend/resume} which
correctly sets the PCI EP state.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace ugly macroses on functions.
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch avoids that sparse complains about casts to restricted __be32.
Fixes: a3cdaa69e4 ("cxgb4: Adds CPL support for Shared Receive Queues")
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Acked-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
In commit ab123fe071 ("enic: handle mtu change for vf properly")
ASSERT_RTNL() is added to _enic_change_mtu() to prevent it from being
called without rtnl held. enic_probe() calls enic_change_mtu()
without rtnl held. At this point netdev is not registered yet.
Remove call to enic_change_mtu and assign the mtu to netdev->mtu.
Fixes: ab123fe071 ("enic: handle mtu change for vf properly")
Signed-off-by: Govindarajulu Varadarajan <gvaradar@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After introduction of the cited commit, mlx5e_build_nic_params
receives the netdevice mtu in order to set the sw_mtu of mlx5e_params.
For enhanced IPoIB, the netdevice mtu is not set in this stage,
therefore, the initial sw_mtu equals zero. As a result, the hw_mtu
of the receive queue will be calculated incorrectly causing traffic
issues.
To fix this issue, query for port mtu before building the nic params.
Fixes: 472a1e44b3 ("net/mlx5e: Save MTU in channels params")
Signed-off-by: Feras Daoud <ferasda@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
MTU helper function is used by both conventional mlx5e
instances (PF/VF) and the eswitch representors. The representor
shouldn't change the nic vport context MTU, the VF is responsible for
that. Therefore set_mtu_cb has a null value when changing the
representor MTU.
Fixes: 250a42b6a7 ("net/mlx5e: Support configurable MTU for vport representors")
Signed-off-by: Adi Nissim <adin@mellanox.com>
Reviewed-by: Yevgeny Kliteynik <kliteyn@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
The hairpin offload code has dependency on the trust mode being PCP.
Hence we should set PCP as the default for handling cases where we are
disallowed to read the trust mode from the FW, or failed to initialize it.
Fixes: 106be53b6b ('net/mlx5e: Set per priority hairpin pairs')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Execute mlx5_eswitch_init() only if we have MLX5_ESWITCH_MANAGER
capabilities.
Do the same for mlx5_eswitch_cleanup().
Fixes: a9f7705ffd ("net/mlx5: Unify vport manager capability check")
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Version 1 of the patch adding SERDES support to the 88E6141/6341
correctly added the ops to the 88E6141/6341. However, by the time
version 3 was committed, the ops had moved to the 88E6085/6175. Put
them back where they belong.
Fixes: 5bafeb6e7e ("net: dsa: mv88e6xxx: 88E6141/6341 SERDES support")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Last set of fixes before 4.18 is released
iwlwifi
* add new IDs for cards already available on the market
brcmfmac
* fix a regression introduced in v4.17
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJbYDWEAAoJEG4XJFUm622bPGUH+QHGcuazgPqR4TsQXwmfNdJB
HJdsx90WW6TLMDzF9EquA4ontBggq2Mdnorxt1SIXK+ZeajFWZlKyl5ol24TtOH3
9uFhQRID2KlWPnwgrBTsFAiNNJar+X4GoUX1SqFz8VJnkYgfdtBHaVK59HdWSp5e
2rVaG/ORUMNnY58f6jr9wOhn/miC1CKuJk5j83CN2KlETkqj/VoGUE2dShdJl0wu
+4iYznIwhG9f6KykReaBmJbh4xu6AEqkFbadKGwWcChR3DDmzDAsWzkcWEocx8ZY
EpoF6vW8GoBB2RE2Syg/Y6exQGnDb4itYQYxvJV1qV52XwYfvDzCdlbLn+kv34I=
=4wJj
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-for-davem-2018-07-31' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers
Kalle Valo says:
====================
wireless-drivers fixes for 4.18
Last set of fixes before 4.18 is released
iwlwifi
* add new IDs for cards already available on the market
brcmfmac
* fix a regression introduced in v4.17
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
We don't maintain tx counters in rx stats any more. There's no need
for an extra container of rq stats.
Cc: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 5b8f3c8d30 ("virtio_net: Add XDP related stats") tries to
count TX XDP stats in virtnet_receive(). This will cause several
issues:
- virtnet_xdp_sq() was called without checking whether or not XDP is
set. This may cause out of bound access when there's no enough txq
for XDP.
- Stats were updated even if there's no XDP/XDP_TX.
Fixing this by reusing virtnet_xdp_xmit() for XDP_TX which can counts
TX XDP counter itself and remove the unnecessary tx stats embedded in
rx stats.
Reported-by: syzbot+604f8271211546f5b3c7@syzkaller.appspotmail.com
Fixes: 5b8f3c8d30 ("virtio_net: Add XDP related stats")
Cc: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 58b99ee3e3 ("net/mlx5e: Add support for XDP_REDIRECT in device-out side")
forgot to return/free the xdp_frame in case the DMA mapping failed, correct this.
Also DMA unmap the frame in case mlx5e_xmit_xdp_frame() fails.
Fixes: 58b99ee3e3 ("net/mlx5e: Add support for XDP_REDIRECT in device-out side")
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
HW requires Rx buffers to be 4 bytes aligned. Modify the driver to
meet this requirement.
Enable OFU rdy valid bug fix, to prevent hang in oful34_rx while
there is back-pressure from host during RX.
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Currently the driver doesn't support secured boot flow, hence
prevent FW download in case HW is configured for such a flow.
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Currently wil6210 ignores the channel field in the
cfg80211_mgmt_tx_params struct for wil_cfg80211_ops mgmt_tx operation
and sends all management frames on the serving channel.
Add support for off-channel transmission of management frames
(WIPHY_FLAG_OFFCHAN_TX) in AP mode. This is useful in enterprise APs
for sending custom probe request frames.
Signed-off-by: Ahmad Masri <amasri@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Align to latest version of the auto generated wmi file
describing the interface with FW.
Signed-off-by: Ahmad Masri <amasri@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Single MSI is the current default configuration.
With multiple MSI interrupts configuration, Tx/Rx processing could
run in parallel on different CPU cores and allow better balance
between the cores.
Signed-off-by: Alexei Avshalom Lazar <ailizaro@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
FW file name for Talyn device can be different from the default name.
In such a case use a corresponding board file name.
If such a board file is not present FW download procedure will fail.
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Firmware ready event may take longer than
current timeout in some scenarios, for example
with multiple RFs connected where each
requires an initial calibration.
Increase the timeout to support these scenarios.
Signed-off-by: Hamad Kadmany <hkadmany@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
FW can support BACK window size 64 for performance improvements.
A new FW capability is added for notifying the host on the increased
max BACK win size support.
Defining WIL_MAX_AGG_WSIZE_64 and WIL_MAX_AMPDU_SIZE_128 to be used
in this case.
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Scan is allowed only on client interfaces (STA/P2P).
Allow scan on AP interface so that the AP can discover rouge
or unauthorized neighbor APs.
Signed-off-by: Ahmad Masri <amasri@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Driver can request FW to report link statistics using
WMI_LINK_STATS_CMDID.
FW will report statistics with WMI_LINK_STATS_EVENTID.
Two categories of statistics defined: basic and global.
New "link_stats" debugfs is used for requesting basic statistics
report (write) and for reading the basic statistics (read).
"link_stats_global" debugfs is used for requesting and reading the
global statistics.
Signed-off-by: Dedy Lansky <dlansky@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
With some tool chains compilation fails due to type
mismatch of the arguments passed to min().
Use min_t() to solve these compilation errors.
Signed-off-by: Alexei Avshalom Lazar <ailizaro@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Extend MSI support to 3-MSI in order to load balance the tx\rx
interrupts between different cores.
use_msi module parameter has changed to n_msi. Usage:
- Set n_msi to 0 for using INTx
- Set n_msi to 1 for using single MSI
- Set n_msi to 3 for using 3-MSI
In 3-MSI configuration MSI 0 is used for TX interrupts, MSI 1
is used for RX interrupts and MSI 2 is used for MISC interrupts.
Signed-off-by: Alexei Avshalom Lazar <ailizaro@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Align to latest version of the auto generated wmi file
describing the interface with FW.
Signed-off-by: Dedy Lansky <dlansky@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
FW file name for Talyn device is different from the default name.
This patch searches for Talyn specific FW file name and fallback
to the default FW file in case it is not present.
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Currently the driver sets CHECKSUM_UNNECESSARY only in case the HW
doesn't report checksum error.
As ip_summed value is not initialized it is not clear what
the driver will report to the network stack in case of HW checksum
error or in case HW doesn't calculate checksum.
Initialize ip_summed to CHECKSUM_NONE to guarantee checksum
calculation by the network stack in the above cases.
Signed-off-by: Gidon Studinski <gidons@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
For negative temperatures, "temp" debugfs is showing wrong values.
Use signed types so proper calculations is done for sub zero
temperatures.
Signed-off-by: Dedy Lansky <dlansky@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Collect statistics of TX latency. The latency is measured from the time
the HW gets aware of new SKB to transmit until the HW indicates tx
complete for this SKB.
The statistics are shown via new "tx_latency" debugfs.
Signed-off-by: Dedy Lansky <dlansky@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Due to recent change in FW, driver will be notified of corrupted Rx
packets (e.g. MIC error).
Drop such packets before they are delivered to network stack.
Signed-off-by: Dedy Lansky <dlansky@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Store the last received multicast sequence number (SN) part of the TID
info. Drop Rx multicast packets with retry bit set which their SN
is equal to the last received.
Signed-off-by: Dedy Lansky <dlansky@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The flag needs to be cleared for the last packet in the list, not the
first one. Fixes some issues with multicast packet loss for powersave
clients connected to an ath9k AP.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The tx power applied by set_txpower is limited by the CTL (conformance
test limit) entries in the EEPROM. These can change based on the user
configured regulatory domain.
Depending on the EEPROM data this can cause the tx power to become too
limited, if the original regdomain CTLs impose lower limits than the CTLs
of the user configured regdomain.
To fix this issue, set the initial channel limits without any CTL
restrictions and only apply the CTL at run time when setting the channel
and the real tx power.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Ensure that a buffer gets tracked as part of the block-ack window as
soon as it's dequeued from the tid for the first time. Ensure that
double calls to ath_tx_addto_baw (e.g. on retransmission) don't cause
any issues.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fixes missed indications of end of U-APSD service period to mac80211
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The checks already prevents periodic cal from being started while noise
floor calibration runs. It is missing checks for the other way around.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
AR9002 code and the QCA AR9003+ reference code do the same.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
ath6kl_bmi_init() is never called in atomic context.
It calls kzalloc() with GFP_ATOMIC, which is not necessary.
GFP_ATOMIC can be replaced with GFP_KERNEL.
This is found by a static analysis tool named DCNS written by myself.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The QCA4019 hw1.0 firmware 10.4-3.2.1-00050 and 10.4-3.5.3-00053 (and most
likely all other) seem to ignore the WMI_CHAN_FLAG_DFS flag during the
scan. This results in transmission (probe requests) on channels which are
not "available" for transmissions.
Since the firmware is closed source and nothing can be done from our side
to fix the problem in it, the driver has to work around this problem. The
WMI_CHAN_FLAG_PASSIVE seems to be interpreted by the firmware to not
scan actively on a channel unless an AP was detected on it. Simple probe
requests will then be transmitted by the STA on the channel.
ath10k must therefore also use this flag when it queues a radar channel for
scanning. This should reduce the chance of an active scan when the channel
might be "unusable" for transmissions.
Fixes: e8a50f8ba4 ("ath10k: introduce DFS implementation")
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
These were recently introduced and found by checkpatch:
drivers/net/wireless/ath/ath10k/mac.c:6118: Alignment should match open parenthesis
drivers/net/wireless/ath/ath10k/mac.c:6121: Alignment should match open parenthesis
drivers/net/wireless/ath/ath10k/mac.c:6124: Alignment should match open parenthesis
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
'app' is dereferenced before used for the devlink trace point.
In case FW is buggy and sends a control message to a VF queue
we should make sure app is not NULL.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Only rt2800 subdriver of rt2x00 implement sta_add() and sta_remove(),
rt2x00mac_sta_add and rt2x00mac_sta_remove has no callers after
commit 9c87758cf0 ("rt2x00: call sta_add/remove directly in rt2800").
So can be removed.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
rtl8225se_rf_init() is never called in atomic context.
It calls mdelay() to busily wait, which is not necessary.
mdelay() can be replaced with msleep().
This patch only replaces the mdelay() that has >20ms time to wait.
This is found by a static analysis tool named DCNS written by myself.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
probe_atmel_card() is never called in atomic context.
It calls mdelay() to busily wait, which is not necessary.
mdelay() can be replaced with msleep().
This is found by a static analysis tool named DCNS written by myself.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When receiving a beacon or probe response, we should update the
boottime_ns field which is the timestamp the frame was received at.
(cf mac80211.h)
This fixes a scanning issue with Android since it relies on this
timestamp to determine when the AP has been seen for the last time
(via the nl80211 BSS_LAST_SEEN_BOOTTIME parameter).
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
wl1271_warning() already appends a \n to the format,
so adding one to the warning string gives empty lines in the log.
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Some features supported by firmware aren't advertised and there is no
way for a driver to query them. This includes e.g. monitor mode details.
Most firmwares support monitor interface but only the latest ones
/announce/ it with a "monitor" flag in the "cap" iovar. There isn't any
reliable detection method for older firmwares (BRCMF_C_MONITOR was tried
but "it only indicates the core part of the stack supports").
Similarly support for tagging monitor frames and building radiotap
headers can't be reliably detected for all firmwares.
This commit adds table that allows mapping features to firmware version.
It adds mappings for 43602a1 and 4366b1 firmwares from
linux-firmware.git. Both were confirmed to be passing monitor frames.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Reviewed-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When CONFIG_PROC_FS isn't set, gcc warning this:
drivers/net/wireless/intersil/hostap/hostap_hw.c:2901:12: warning: ‘prism2_registers_proc_show’ defined but not used [-Wunused-function]
static int prism2_registers_proc_show(struct seq_file *m, void *v)
drivers/net/wireless/intersil/hostap/hostap_proc.c:16:12: warning: ‘prism2_debug_proc_show’ defined but not used [-Wunused-function]
static int prism2_debug_proc_show(struct seq_file *m, void *v)
^
drivers/net/wireless/intersil/hostap/hostap_proc.c:49:12: warning: ‘prism2_stats_proc_show’ defined but not used [-Wunused-function]
static int prism2_stats_proc_show(struct seq_file *m, void *v)
^
drivers/net/wireless/intersil/hostap/hostap_proc.c:177:12: warning: ‘prism2_crypt_proc_show’ defined but not used [-Wunused-function]
static int prism2_crypt_proc_show(struct seq_file *m, void *v)
^
fix this by adding #ifdef around them.
hfa384x_read_reg is only used by prism2_registers_proc_show,so move it
into #ifdef.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When CONFIG_PROC_FS isn't set, gcc warning this:
drivers/net/wireless/atmel/atmel.c:1402:12: warning: ‘atmel_proc_show’ defined but not used [-Wunused-function]
static int atmel_proc_show(struct seq_file *m, void *v)
^
fix this by adding #ifdef around it.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Pointer 'p' is being assigned but is never used hence it is
redundant and can be removed. Also re-work if statement to remove
redundant assignment of p.
Cleans up clang warning:
warning: variable 'p' set but not used [-Wunused-but-set-variable]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Variables id, unicast, write, conf, a_band, accum_tx and ucode are
assigned a value but it is never read, hence they are redundant and
can be removed.
Cleans up clang warnings:
warning: variable 'id' set but not used [-Wunused-but-set-variable]
warning: variable 'unicast' set but not used [-Wunused-but-set-variable]
warning: variable 'write' set but not used [-Wunused-but-set-variable]
warning: variable 'conf' set but not used [-Wunused-but-set-variable]
warning: variable 'a_band' set but not used [-Wunused-but-set-variable]
warning: variable 'tx' set but not used [-Wunused-but-set-variable]
warning: variable 'accum_tx' set but not used [-Wunused-but-set-variable]
warning: variable 'ucode' set but not used [-Wunused-but-set-variable]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Variables len, ret, reason and crypt are assigned values that
are never read, hence they are redundant and can be removed.
Note: For the variable ret, a return code is being assigned, but
this is not returned and 0 is currently being returned, I believe
this is OK.
Cleans up clang warnings:
warning: variable 'len' set but not used [-Wunused-but-set-variable]
variable 'ret' set but not used [-Wunused-but-set-variable]
warning: variable 'reason' set but not used [-Wunused-but-set-variable]
warning: variable 'crypt' set but not used [-Wunused-but-set-variable]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Variables len and dev assigned values but are never used hence they
are redundant and can be removed. Also add in white space in for-loop
and remove some { } braces on if statement.
Cleans up clang warnings:
warning: variable 'len' set but not used [-Wunused-but-set-variable]
warning: variable 'dev' set but not used [-Wunused-but-set-variable]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
common->init_done flag should set after basic initialization. Hence,
moving init_done flag at end of rsi_91x_init().
Signed-off-by: Amol Hanwate <amol.hanwate@redpinesignals.com>
Signed-off-by: Siva Rebbagondla <siva.rebbagondla@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
rx_params are getting updated two times in driver, which is not required.
Hence, removing duplicate updation of rx_params from rsi_prepare_skb().
Signed-off-by: Amol Hanwate <amol.hanwate@redpinesignals.com>
Signed-off-by: Siva Rebbagondla <siva.rebbagondla@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Currently, RSI_NEEDED_HEADROOM is '80' for rsi driver, which is wrong.
As per rsi internal frame format, the RSI_NEEDED_HEADROOM shall be '84',
which is 64(dword_align) + 4(extended_desc) + 16(frame_desc).
Hence, corrected the needed headroom.
Signed-off-by: Amol Hanwate <amol.hanwate@redpinesignals.com>
Signed-off-by: Siva Rebbagondla <siva.rebbagondla@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Currently, AP mode will work on only WLAN alone firmware. To give support
for AP and BT dual mode, adding firmware entry in 'struct ta_metadata'.
The firmware entry is based on what coex_mode is used in driver and coex
mode '4' for all AP+BT related functionalities. Hence, added the same.
Signed-off-by: Siva Rebbagondla <siva.rebbagondla@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
while cleaning up the driver, observed that flash_content pointer is not
necessary in rsi_load_firmware(). Instead of this, driver can use
'fw_entry->data' directly.Hence, removed redundant flash_content pointer.
Signed-off-by: Siva Rebbagondla <siva.rebbagondla@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Wei Yongjun