OMAP4430 is embedded with UTMI PHY. This PHY does not support the
OTG features like ID pin detection and VBUS detection. This function
is exported to an external companion chip TWL6030. Software must retrieve
the OTG HNP and SRP status from the TWL6030 and configure the bits inside
the control module that drive the related USBOTGHS UTMI interface signals.
It must also read back the UTMI signals needed to configure the TWL6030
OTG module.
Can find more details in the TRM[1].
[1]:http://focus.ti.com/pdfs/wtbu/OMAP4430_ES2.0_Public_TRM_vJ.pdf
In OMAP4430 musb driver VBUS and ID notifications are received from the
transceiver driver. If the cable/device is connected during boot,
notifications from transceiver driver will be missed till musb driver
is loaded.
Patch to configure the transceiver in the platform_enable/disable
functions and enable the vbus in the gadget driver based on the
last_event of the otg_transceiver.
Signed-off-by: Hema HK <hemahk@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Save the last event in the otg_transceiver so that it can used in the
musb driver and gadget driver to configure the musb and enable the
vbus for host mode and OTG mode, if the device is connected during boot.
Signed-off-by: Hema HK <hemahk@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Introduce the twl6030_phy_suspend function and assign to otg.set_suspend
function pointer.
This function is used by the musb-omap2430 platform driver
during suspend/resume.
Signed-off-by: Hema HK <hemahk@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
To get the ID status there was an I2C read transfer. Removed this I2C
read transfer as this info can be used from existing variable(linkstat).
Signed-off-by: Hema HK <hemahk@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Remove the regulator enable while driver loading and enable it only when
the cable/device is connected and disable it when disconnected.
Remove the configuration of config_state and config_trans register
configuration as these registers are programmed when regulator
enable/disable is called.
Signed-off-by: Hema HK <hemahk@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Calling runtime pm APIs pm_runtime_put_sync() and pm_runtime_get_sync()
for enabling/disabling the clocks, sysconfig settings.
Enable clock, configure no-idle/standby when active and configure force idle/standby
and disable clock when idled. This is taken care by the runtime framework when
driver calls the pm_runtime_get_sync and pm_runtime_put_sync APIs.
Need to configure MUSB into force standby and force idle mode when usb not used
Signed-off-by: Hema HK <hemahk@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Cousson, Benoit <b-cousson@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
struct usb_request's list_head is supposed to be
used only by gadget drivers, but musb is abusing
that. Give struct musb_request its own list_head
and prevent musb from poking into other driver's
business.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Just a few cosmetic fixes to usb_gadget_probe_driver()
and usb_gadget_unregister_driver().
Decreased a few indentation levels with goto statements.
While at that, also add the missing call to musb_stop().
If we don't have OTG, there's no point of leaving
MUSB prepared for operation if a gadget driver fails
to probe. The same is valid for usb_gadget_unregister_driver(),
since we are removing the gadget driver and we don't have
OTG, we can completely unconfigure MUSB.
Signed-off-by: Felipe Balbi <balbi@ti.com>
During development, even though board is wired
to e.g. OTG, we might want to compile host-only
or peripheral-only configurations.
Let's allow that to happen.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Use bitmap_set()/bitmap_clear() to fill/zero a region of a bitmap
instead of doing set_bit()/clear_bit() each bit.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Now that ehci_run don't call ehci_reset, we can use ehci_run.
Signed-off-by: Matthieu CASTET <castet.matthieu@parrot.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
TDI driver does the ehci_reset in their reset callback.
Don't reset in ehci_run because configuration settings done in
platform driver will be reset.
This will allow to make msm use ehci_run.
Signed-off-by: Matthieu CASTET <castet.matthieu@parrot.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The driver private data is retrieved incorrectly which results
a crash when written into "mode" debugfs file.
Signed-off-by: Pavankumar Kondeti <pkondeti@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fixes the below compiler warning
drivers/usb/otg/msm72k_otg.c:257: warning: 'msm_otg_suspend' defined but not used
Signed-off-by: Pavankumar Kondeti <pkondeti@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
resumption of devices can fail. Errors must be handled.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The device never needs to be resumed in close(). But the counters
must be balanced. As resumption can fail, but the counters must
be balanced, use the _no_resume() version which cannot fail.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If an error happens during resumption.
The remaining data has to be cleanly discarded and the pm
counters have to be adjusted.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
As soon as the first error happens, the write must
be stopped, lest we send mutilated messages.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
An error in the write code path would permanently disable
runtime PM in this driver
Signed-off-by: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This fixes two errors:
- the device is busy if a message was recieved even if resubmission fails
- the device is not busy if resubmission fails due to -EPERM
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The document says:
|2.1 Problem description
| When at least two USB devices are simultaneously running, it is observed that
| sometimes the INT corresponding to one of the USB devices stops occurring. This may
| be observed sometimes with USB-to-serial or USB-to-network devices.
| The problem is not noticed when only USB mass storage devices are running.
|2.2 Implication
| This issue is because of the clearing of the respective Done Map bit on reading the ATL
| PTD Done Map register when an INT is generated by another PTD completion, but is not
| found set on that read access. In this situation, the respective Done Map bit will remain
| reset and no further INT will be asserted so the data transfer corresponding to that USB
| device will stop.
|2.3 Workaround
| An SOF INT can be used instead of an ATL INT with polling on Done bits. A time-out can
| be implemented and if a certain Done bit is never set, verification of the PTD completion
| can be done by reading PTD contents (valid bit).
| This is a proven workaround implemented in software.
Russell King run into this with an USB-to-serial converter. This patch
implements his suggestion to enable the high frequent SOF interrupt only
at the time we have ATL packages queued. It goes even one step further
and enables the SOF interrupt only if we have more than one ATL packet
queued at the same time.
Cc: <stable@kernel.org> # [2.6.35.x, 2.6.36.x, 2.6.37.x]
Tested-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
ehci_lpm_set_da and ehci_lpm_check are EHCI 1.1 specific functions which
are not used on many platforms but do generate annoying gcc warnings
Signed-off-by: Maksim Rayskiy <mrayskiy@broadcom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We need FUSB300_MAX_NUM_EP (16) names otherwise the last 8 names get
initialized to garbage values in fusb300_probe().
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is a patch that seems to make the USB hangs on the S3C244X go away.
At least a good amount of ping torture didn't make them come back so far.
The issue is that, if there are several back-to-back packets, sometimes no
interrupt is generated for one of them. This seems to be caused by the
mysterious dual packet mode, which the USB hardware enters automatically
if the endpoint size is half that of the FIFO. (On the 244X, this is the
normal situation for bulk data endpoints.)
There is also a timing factor in this. It seems that what happens is that
the USB hardware automatically sends an acknowledgement if there is only one
packet in the FIFO (the FIFO has space for two). If another packet arrives
before the host has retrieved and acknowledged the previous one, no interrupt
is generated for that second one.
However, there may be an indication. There is one undocumented bit (none
of the 244x manuals document it), OUT_CRS1_REG[1], that seems to be set
suspiciously often when this condition occurs. There is also
CLR_DATA_TOGGLE, OUT_CRS1_REG[7], which may have a function related to
this. (The Samsung manual is rather terse on that, as usual.)
This needs to be examined further. For now, the patch seems to do the
trick.
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This PCH_UDC driver does not work normally when "Ethernet gadget" is used.
This patch fixed this issue.
The following was modified.
- The FIFO flush process.
- The descriptor creation process.
- The adjustment of DMA buffer align.
Currently the PCH_UDC driver can work normally with "Ethernet gadget",
"Serial gadget" or "File-backed Storage Gadget".
Signed-off-by: Toshiharu Okada <toshiharu-linux@dsn.okisemi.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Reorder the driver->name assignment so the 'iProduct' could be initialized
as well if both 'name' and 'iProduct' come as NULL by default.
Also, remove the misplaced 'extern' keyword.
Signed-off-by: Jassi Brar <jassi.brar@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
While checking valid interface number we should compare MAX_CONFIG_INTERFACES
with the variable 'intf' (which holds the lower 8bits of w_index) rather than
'w_index'
Signed-off-by: Jassi Brar <jassi.brar@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is needed to resolve some merge conflicts that were found
in the USB host controller patches, and reported by Stephen Rothwell.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This reverts commit b7d5b439b7.
It conflicts with commit baab93afc2 "USB:
EHCI: ASPM quirk of ISOC on AMD Hudson" and merging the two just doesn't
work properly.
Cc: Andiry Xu <andiry.xu@amd.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Alex He <alex.he@amd.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu:
m68knommu: set flow handler for secondary interrupt controller of 5249
m68knommu: remove use of IRQ_FLG_LOCK from 68360 platform support
m68knommu: fix dereference of port.tty
m68knommu: add missing linker __modver section
m68knommu: fix mis-named variable int set_irq_chip loop
m68knommu: add optimize memmove() function
m68k: remove arch specific non-optimized memcmp()
m68knommu: fix use of un-defined _TIF_WORK_MASK
m68knommu: Rename m548x_wdt.c to m54xx_wdt.c
m68knommu: fix m548x_wdt.c compilation after headers renaming
m68knommu: Remove dependencies on nonexistent M68KNOMMU
The struct_tty associated with a port is now a direct pointer
from within the local private driver info struct. So fix all uses
of it.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
* 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6: (27 commits)
drm/radeon/kms: hopefully fix pll issues for real (v3)
drm/radeon/kms: add bounds checking to avivo pll algo
drm: fix wrong usages of drm_device in DRM Developer's Guide
drm/radeon/kms: fix a few more atombios endian issues
drm/radeon/kms: improve 6xx/7xx CS error output
drm/radeon/kms: check AA resolve registers on r300
drm/radeon/kms: fix tracking of BLENDCNTL, COLOR_CHANNEL_MASK, and GB_Z on r300
drm/radeon/kms: use linear aligned for evergreen/ni bo blits
drm/radeon/kms: use linear aligned for 6xx/7xx bo blits
drm/radeon: fix race between GPU reset and TTM delayed delete thread.
drm/radeon/kms: evergreen/ni big endian fixes (v2)
drm/radeon/kms: 6xx/7xx big endian fixes
drm/radeon/kms: atombios big endian fixes
drm/radeon: 6xx/7xx non-kms endian fixes
drm/radeon/kms: optimize CS state checking for r100->r500
drm: do not leak kernel addresses via /proc/dri/*/vma
drm/radeon/kms: add connector table for mac g5 9600
radeon mkregtable: Add missing fclose() calls
drm/radeon/kms: fix interlaced modes on dce4+
drm/radeon: fix memory debugging since d961db75ce
...
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/security-testing-2.6:
pci: use security_capable() when checking capablities during config space read
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6:
ACPI / Video: Probe for output switch method when searching video devices.
ACPI / Wakeup: Enable button GPEs unconditionally during initialization
ACPI / ACPICA: Avoid crashing if _PRW is defined for the root object
ACPI: Fix acpi_os_read_memory() and acpi_os_write_memory() (v2)
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/djbw/async_tx: (21 commits)
dmaengine: add slave-dma maintainer
dma: ipu_idmac: do not lose valid received data in the irq handler
dmaengine: imx-sdma: fix up param for the last BD in sdma_prep_slave_sg()
dmaengine: imx-sdma: correct sdmac->status in sdma_handle_channel_loop()
dmaengine: imx-sdma: return sdmac->status in sdma_tx_status()
dmaengine: imx-sdma: set sdmac->status to DMA_ERROR in err_out of sdma_prep_slave_sg()
dmaengine: imx-sdma: remove IMX_DMA_SG_LOOP handling in sdma_prep_slave_sg()
dmaengine i.MX dma: initialize dma capabilities outside channel loop
dmaengine i.MX DMA: do not initialize chan_id field
dmaengine i.MX dma: check sg entries for valid addresses and lengths
dmaengine i.MX dma: set maximum segment size for our device
dmaengine i.MX SDMA: reserve channel 0 by not registering it
dmaengine i.MX SDMA: initialize dma capabilities outside channel loop
dmaengine i.MX SDMA: do not initialize chan_id field
dmaengine i.MX sdma: check sg entries for valid addresses and lengths
dmaengine i.MX sdma: set maximum segment size for our device
DMA: PL08x: fix channel pausing to timeout rather than lockup
DMA: PL08x: fix infinite wait when terminating transfers
dmaengine: imx-sdma: fix inconsistent naming in sdma_assign_cookie()
dmaengine: imx-sdma: propagate error in sdma_probe() instead of returning 0
...
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, dmi, debug: Log board name (when present) in dmesg/oops output
x86, ioapic: Don't warn about non-existing IOAPICs if we have none
x86: Fix mwait_usable section mismatch
x86: Readd missing irq_to_desc() in fixup_irq()
x86: Fix section mismatch in LAPIC initialization
This reintroduces commit 47970b1b which was subsequently reverted
as f00eaeea. The original change was broken and caused X startup
failures and generally made privileged processes incapable of reading
device dependent config space. The normal capable() interface returns
true on success, but the LSM interface returns 0 on success. This thinko
is now fixed in this patch, and has been confirmed to work properly.
So, once again...Eric Paris noted that commit de139a3 ("pci: check caps
from sysfs file open to read device dependent config space") caused the
capability check to bypass security modules and potentially auditing.
Rectify this by calling security_capable() when checking the open file's
capabilities for config space reads.
Reported-by: Eric Paris <eparis@redhat.com>
Tested-by: Dave Young <hidave.darkstar@gmail.com>
Acked-by: James Morris <jmorris@namei.org>
Cc: Dave Airlie <airlied@gmail.com>
Cc: Alex Riesen <raa.lkml@gmail.com>
Cc: Sedat Dilek <sedat.dilek@googlemail.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: James Morris <jmorris@namei.org>
The "Type 2" SMBIOS record that contains Board Name is not
strictly required and may be absent in the SMBIOS on some
platforms.
( Please note that Type 2 is not listed in Table 3 in Sec 6.2
("Required Structures and Data") of the SMBIOS v2.7
Specification. )
Use the Manufacturer Name (aka System Vendor) name.
Print Board Name only when it is present.
Before the fix:
(i) dmesg output: DMI: /ProLiant DL380 G6, BIOS P62 01/29/2011
(ii) oops output: Pid: 2170, comm: bash Not tainted 2.6.38-rc4+ #3 /ProLiant DL380 G6
After the fix:
(i) dmesg output: DMI: HP ProLiant DL380 G6, BIOS P62 01/29/2011
(ii) oops output: Pid: 2278, comm: bash Not tainted 2.6.38-rc4+ #4 HP ProLiant DL380 G6
Signed-off-by: Naga Chumbalkar <nagananda.chumbalkar@hp.com>
Reviewed-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: <stable@kernel.org> # .3x - good for debugging, please apply as far back as it applies cleanly
LKML-Reference: <20110214224423.2182.13929.sendpatchset@nchumbalkar.americas.hpqcorp.net>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The problematic boards have a recommended reference divider
to be used when spread spectrum is enabled on the laptop panel.
Enable the use of the recommended reference divider along with
the new pll algo.
v2: testing options
v3: When using the fixed reference divider with LVDS, prefer
min m to max p and use fractional feedback dividers.
Fixes:
https://bugzilla.kernel.org/show_bug.cgi?id=28852https://bugzilla.kernel.org/show_bug.cgi?id=24462https://bugzilla.kernel.org/show_bug.cgi?id=26552
MacbookPro issues reported by Justin Mattock <justinmattock@gmail.com>
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
* 'rtc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
RTC: Fix minor compile warning
RTC: Convert rtc drivers to use the alarm_irq_enable method
RTC: Fix rtc driver ioctl specific shortcutting
Currently when two or more buffers are queued by the camera driver
and so the double buffering is enabled in the idmac, we lose one
frame comming from CSI since the reporting of arrival of the first
frame is deferred by the DMAIC_7_EOF interrupt handler and reporting
of the arrival of the last frame is not done at all. So when requesting
N frames from the image sensor we actually receive N - 1 frames in
user space.
The reason for this behaviour is that the DMAIC_7_EOF interrupt
handler misleadingly assumes that the CUR_BUF flag is pointing to the
buffer used by the IDMAC. Actually it is not the case since the
CUR_BUF flag will be flipped by the FSU when the FSU is sending the
<TASK>_NEW_FRM_RDY signal when new frame data is delivered by the CSI.
When sending this singal, FSU updates the DMA_CUR_BUF and the
DMA_BUFx_RDY flags: the DMA_CUR_BUF is flipped, the DMA_BUFx_RDY
is cleared, indicating that the frame data is beeing written by
the IDMAC to the pointed buffer. DMA_BUFx_RDY is supposed to be
set to the ready state again by the MCU, when it has handled the
received data. DMAIC_7_CUR_BUF flag won't be flipped here by the
IPU, so waiting for this event in the EOF interrupt handler is wrong.
Actually there is no spurious interrupt as described in the comments,
this is the valid DMAIC_7_EOF interrupt indicating reception of the
frame from CSI.
The patch removes code that waits for flipping of the DMAIC_7_CUR_BUF
flag in the DMAIC_7_EOF interrupt handler. As the comment in the
current code denotes, this waiting doesn't help anyway. As a result
of this removal the reporting of the first arrived frame is not
deferred to the time of arrival of the next frame and the drivers
software flag 'ichan->active_buffer' is in sync with DMAIC_7_CUR_BUF
flag, so the reception of all requested frames works.
This has been verified on the hardware which is triggering the
image sensor by the programmable state machine, allowing to
obtain exact number of frames. On this hardware we do not tolerate
losing frames.
This patch also removes resetting the DMA_BUFx_RDY flags of
all channels in ipu_disable_channel() since transfers on other
DMA channels might be triggered by other running tasks and the
buffers should always be ready for data sending or reception.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Reviewed-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Tested-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
* 'intel/drm-intel-fixes' of /ssd/git/drm-next:
drm/i915: Fix resume regression from 5d1d0cc
drm/i915/tv: Use polling rather than interrupt-based hotplug
drm/i915: Trigger modesetting if force-audio changes
drm/i915/sdvo: If we have an EDID confirm it matches the mode of the connection
drm/i915: Disable RC6 on Ironlake
drm/i915/lvds: Restore dithering on native modes for gen2/3
drm/i915: Invalidate TLB caches on SNB BLT/BSD rings
Hema HK