Previously the driver would use devm_* related functions at
the codec level probe() to allocate clock resources for MCLK
and the DAI clocks exposed by the device. This caused issues
when registering clocks on a re-probe (no device level
remove/prove involved) as the devm_* resources were never
freed up so the clocks were still registered from the previous
codec level probe().
This commit updates the clock handling for MCLK usage and DAI
clock provision to fix this discrepancy and allow the codec level
probe/remove functionality to operate as intended.
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Link: https://lore.kernel.org/r/b92c461baeed27a6cd92e59e36a55c2547218683.1597164865.git.Adam.Thomson.Opensource@diasemi.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 3029 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070032.746973796@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For the purposes of platforms which use the codec as DAI clock
master for the CPU and other codec devices, there is the need to
not only expose the clock gating of BCLK and WCLK but also the
ability to set those rates without going through the ASoC APIs.
To make this possible, the previous CCF implementation in the
driver has been extended to separate BCLK and WCLK out. WCLK is
the parent clock to BCLK, and is also the clock gate for both.
BCLK in HW is a factor/multiplier of WCLK so derives from whatever
SR is chosen for WCLK, hence the need to make it a child of WCLK
for the purposes of CCF. Enabling/disabling either BCLK or WCLK
will result in clocks being ungated/gated accordingly. To simplify
matters, these clocks can only be configured if the codec is set
as master, otherwise CCF control is disallowed.
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Previously the driver would default the BCLK periods per WCLK to
64, to cover all possible non-TDM scenarios when the codec was
DAI clock master. However some devices require a lower BCLK rate
to operate correctly so with this in mind, this commit updates
the code to be more dynamic, with BCLK rate now based on SR and
word length provided to hw_params().
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
By making MCLK parent of DAI clocks, when querying the rate of the
clock the rate returned is now given from the parent clock so
gives the MCLK rate rather than 0 as previously returned. This is
a bit misleading, and actually there's no major reason why we can't
at least return the DAI WCLK rate, as set in HW, so that's what we
now do.
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
On some platforms it has been noted that a pop noise can be
witnessed when capturing audio, mainly for first time after a
headset jack has been inserted. This is due to a DC offset in the
Mic PGA and so to avoid this delays are required when powering
up the capture path.
This commit rectifies the problem by adding delays post Mic PGA and
post Mixin PGA. The post Mic PGA delay is determined based on
Mic Bias voltage, and is only applied the first time after a
headset jack is inserted.
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
There is a need to use DA7219 as DAI clock master for other codecs
within a system, which means that the DAI clocks are required to
remain, regardless of whether the codec is actually running
playback/capture. To be able to expose control of the DAI clocking
the common clock framework has been employed.
The current implementation adds a simple clock gate for enabling
and disabling the DAI clocks, with no rate control supported
(this is still handled through standard hw_params() functions as
before). If DT is enabled then the clock is added to the OF
providers list, otherwise a clkdev lookup is used.
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently when HP detection procedure runs for certain MCLK
frequencies, when PLL is bypassed, the procedure will incorrectly
report Lineout instead of Headphones due to timing incosistencies.
To avoid this problem, the PLL is temporarily enabled (if currently
bypassed and MCLK present) to provide consistent timings for the
procedure, regardless of MCLK frequency.
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Acked-by: Sathyanarayana Nujella <sathyanarayana.nujella@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently on some headsets slight pops can be heard during DAPM
power-up/down. This can also be witnessed during the HP detect
procedure. This patch addresses the issue by adjusting DAPM power
sequencing slightly, the introduction of delays and use of
minimum HP gain to avoid such noise artefacts.
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently if AAD is enabled in the device, during system suspend
the feature remains, regardless of whether the codec is a wake-up
source or not. This means some additional power is being used
which is unnecessary, and can causes issues with some platforms'
IRQ handlers where state changes during system suspend aren't
captured.
This patch updates the driver to disable AAD during suspend, if
we're not a wake-up source, and then re-enables this on resume.
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently the reset code in i2c_probe only resets the AAD part of
the device and not the entire codec. This patch updates the driver
to resolve this and ensures that if the codec is still active from
a previous boot then the audio paths are powered down prior to
reset.
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently the driver code assumes that MCLK will be present during
the procedure, or if it has control of MCLK then it can make sure
it's enabled. Some platforms however do not provide MCLK to the
driver in this way, and will not leave MCLK enabled when Codec is
in STANDBY state.
This patch adds support for the HP detect procedure when running
from the device's internal oscillator, to ensure all platforms
can make use of this feature correctly.
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The expected MCLK frequency ranges and the associated dividers
are updated to improve PLL locking in a corner scenario, with low
MCLK frequency near an input divider change boundary.
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
PLL mode based on 32KHz master clock not supported in
AB silicon so remove support from the driver.
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In AB silicon, the internal LDO is not supported so remove
DT and driver references to this (digital voltage direct from
'VDD' supply)
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This adds support for the DA7219 audio codec with built-in advanced
accessory detect features.
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Adam Thomson