commit 00dcf2fa449f23a263343d7fe051741bdde65d0b upstream.
When operating in High-Speed, it is observed that DSTS[USBLNKST] doesn't
update link state immediately after receiving the wakeup interrupt. Since
wakeup event handler calls the resume callbacks, there is a chance that
function drivers can perform an ep queue, which in turn tries to perform
remote wakeup from send_gadget_ep_cmd(STARTXFER). This happens because
DSTS[[21:18] wasn't updated to U0 yet, it's observed that the latency of
DSTS can be in order of milli-seconds. Hence avoid calling gadget_wakeup
during startxfer to prevent unnecessarily issuing remote wakeup to host.
Fixes: c36d8e947a ("usb: dwc3: gadget: put link to U0 before Start Transfer")
Cc: stable@vger.kernel.org
Suggested-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Prashanth K <quic_prashk@quicinc.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20240828064302.3796315-1-quic_prashk@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9149c9b0c7e046273141e41eebd8a517416144ac upstream.
This fix addresses STAR 9001285599, which only affects DWC_usb3 version
3.20a. The timer value for PM_LC_TIMER in DWC_usb3 3.20a for the Link
ECN changes is incorrect. If the PM TIMER ECN is enabled via GUCTL2[19],
the link compliance test (TD7.21) may fail. If the ECN is not enabled
(GUCTL2[19] = 0), the controller will use the old timer value (5us),
which is still acceptable for the link compliance test. Therefore, clear
GUCTL2[19] to pass the USB link compliance test: TD 7.21.
Cc: stable@vger.kernel.org
Signed-off-by: Faisal Hassan <quic_faisalh@quicinc.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20240829094502.26502-1-quic_faisalh@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit ee0d382feb44ec0f445e2ad63786cd7f3f6a8199 ]
We should verify the bound of the array to assure that host
may not manipulate the index to point past endpoint array.
Found by static analysis.
Signed-off-by: Ma Ke <make24@iscas.ac.cn>
Reviewed-by: Andrew Jeffery <andrew@codeconstruct.com.au>
Acked-by: Andrew Jeffery <andrew@codeconstruct.com.au>
Link: https://lore.kernel.org/r/20240625022306.2568122-1-make24@iscas.ac.cn
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9d32685a251a754f1823d287df233716aa23bcb9 ]
Set the host status byte when a data completion error is encountered
otherwise the upper layer may end up using the invalid zero'ed data.
The following output was observed from scsi/sd.c prior to this fix.
[ 11.872824] sd 0:0:0:1: [sdf] tag#9 data cmplt err -75 uas-tag 1 inflight:
[ 11.872826] sd 0:0:0:1: [sdf] tag#9 CDB: Read capacity(16) 9e 10 00 00 00 00 00 00 00 00 00 00 00 20 00 00
[ 11.872830] sd 0:0:0:1: [sdf] Sector size 0 reported, assuming 512.
Signed-off-by: Shantanu Goel <sgoel01@yahoo.com>
Acked-by: Oliver Neukum <oneukum@suse.com>
Link: https://lore.kernel.org/r/87msnx4ec6.fsf@yahoo.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 99516f76db48e1a9d54cdfed63c1babcee4e71a5 ]
ucsi_register_altmode checks IS_ERR for the alt pointer and treats
NULL as valid. When CONFIG_TYPEC_DP_ALTMODE is not enabled,
ucsi_register_displayport returns NULL which causes a NULL pointer
dereference in trace. Rather than return NULL, call
typec_port_register_altmode to register DisplayPort alternate mode
as a non-controllable mode when CONFIG_TYPEC_DP_ALTMODE is not enabled.
Reviewed-by: Benson Leung <bleung@chromium.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Signed-off-by: Jameson Thies <jthies@google.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20240510201244.2968152-2-jthies@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8b6b386f9aa936ed0c190446c71cf59d4a507690 ]
Skip submitting URBs, when identical requests were already sent in
tweak_special_requests(). Instead call the completion handler directly
to return the result of the URB.
Even though submitting those requests twice should be harmless, there
are USB devices that react poorly to some duplicated requests.
One example is the ChipIdea controller implementation in U-Boot: The
second SET_CONFIGURATION request makes U-Boot disable and re-enable all
endpoints. Re-enabling an endpoint in the ChipIdea controller, however,
was broken until U-Boot commit b272c8792502 ("usb: ci: Fix gadget
reinit").
Signed-off-by: Simon Holesch <simon@holesch.de>
Acked-by: Shuah Khan <skhan@linuxfoundation.org>
Reviewed-by: Hongren Zheng <i@zenithal.me>
Tested-by: Hongren Zheng <i@zenithal.me>
Link: https://lore.kernel.org/r/20240519141922.171460-1-simon@holesch.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 740f2e2791b98e47288b3814c83a3f566518fed2 upstream.
Stop Endpoint command on LINK TRB with TC bit set to 1 causes that
internal cycle bit can have incorrect state after command complete.
In consequence empty transfer ring can be incorrectly detected
when EP is resumed.
NOP TRB before LINK TRB avoid such scenario. Stop Endpoint command
is then on NOP TRB and internal cycle bit is not changed and have
correct value.
Fixes: 3d82904559 ("usb: cdnsp: cdns3 Add main part of Cadence USBSSP DRD Driver")
cc: <stable@vger.kernel.org>
Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Reviewed-by: Peter Chen <peter.chen@kernel.org>
Link: https://lore.kernel.org/r/PH7PR07MB953878279F375CCCE6C6F40FDD8E2@PH7PR07MB9538.namprd07.prod.outlook.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3a8839bbb86da7968a792123ed2296d063871a52 upstream.
Device attribute group @usb3_hardware_lpm_attr_group is merged by
add_power_attributes(), but it is not unmerged explicitly, fixed by
unmerging it in remove_power_attributes().
Fixes: 655fe4effe ("usbcore: add sysfs support to xHCI usb3 hardware LPM")
Cc: stable@vger.kernel.org
Signed-off-by: Zijun Hu <quic_zijuhu@quicinc.com>
Link: https://lore.kernel.org/r/20240820-sysfs_fix-v2-1-a9441487077e@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ddfcfeba891064b88bb844208b43bef2ef970f0c upstream.
The probe function never performs any paltform device allocation, thus
error path "undo_platform_dev_alloc" is entirely bogus. It drops the
reference count from the platform device being probed. If error path is
triggered, this will lead to unbalanced device reference counts and
premature release of device resources, thus possible use-after-free when
releasing remaining devm-managed resources.
Fixes: f83fca0707 ("usb: dwc3: add ST dwc3 glue layer to manage dwc3 HC")
Cc: stable@vger.kernel.org
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Link: https://lore.kernel.org/r/20240814093957.37940-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 14e497183df28c006603cc67fd3797a537eef7b9 upstream.
This commit addresses an issue where the USB core could access an
invalid event buffer address during runtime suspend, potentially causing
SMMU faults and other memory issues in Exynos platforms. The problem
arises from the following sequence.
1. In dwc3_gadget_suspend, there is a chance of a timeout when
moving the USB core to the halt state after clearing the
run/stop bit by software.
2. In dwc3_core_exit, the event buffer is cleared regardless of
the USB core's status, which may lead to an SMMU faults and
other memory issues. if the USB core tries to access the event
buffer address.
To prevent this hardware quirk on Exynos platforms, this commit ensures
that the event buffer address is not cleared by software when the USB
core is active during runtime suspend by checking its status before
clearing the buffer address.
Cc: stable <stable@kernel.org>
Signed-off-by: Selvarasu Ganesan <selvarasu.g@samsung.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20240815064836.1491-1-selvarasu.g@samsung.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0b00583ecacb0b51712a5ecd34cf7e6684307c67 upstream.
USB_DEVICE(0x1901, 0x0006) may send data before cdc_acm is ready, which
may be misinterpreted in the default N_TTY line discipline.
Signed-off-by: Ian Ray <ian.ray@gehealthcare.com>
Acked-by: Oliver Neuku <oneukum@suse.com>
Cc: stable <stable@kernel.org>
Link: https://lore.kernel.org/r/20240814072905.2501-1-ian.ray@gehealthcare.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3568affcddd68743e25aa3ec1647d9b82797757b upstream.
As pointed out by Stephen Boyd it is possible that during initialization
of the pmic_glink child drivers, the protection-domain notifiers fires,
and the associated work is scheduled, before the client registration
returns and as a result the local "client" pointer has been initialized.
The outcome of this is a NULL pointer dereference as the "client"
pointer is blindly dereferenced.
Timeline provided by Stephen:
CPU0 CPU1
---- ----
ucsi->client = NULL;
devm_pmic_glink_register_client()
client->pdr_notify(client->priv, pg->client_state)
pmic_glink_ucsi_pdr_notify()
schedule_work(&ucsi->register_work)
<schedule away>
pmic_glink_ucsi_register()
ucsi_register()
pmic_glink_ucsi_read_version()
pmic_glink_ucsi_read()
pmic_glink_ucsi_read()
pmic_glink_send(ucsi->client)
<client is NULL BAD>
ucsi->client = client // Too late!
This code is identical across the altmode, battery manager and usci
child drivers.
Resolve this by splitting the allocation of the "client" object and the
registration thereof into two operations.
This only happens if the protection domain registry is populated at the
time of registration, which by the introduction of commit '1ebcde047c54
("soc: qcom: add pd-mapper implementation")' became much more likely.
Reported-by: Amit Pundir <amit.pundir@linaro.org>
Closes: https://lore.kernel.org/all/CAMi1Hd2_a7TjA7J9ShrAbNOd_CoZ3D87twmO5t+nZxC9sX18tA@mail.gmail.com/
Reported-by: Johan Hovold <johan@kernel.org>
Closes: https://lore.kernel.org/all/ZqiyLvP0gkBnuekL@hovoldconsulting.com/
Reported-by: Stephen Boyd <swboyd@chromium.org>
Closes: https://lore.kernel.org/all/CAE-0n52JgfCBWiFQyQWPji8cq_rCsviBpW-m72YitgNfdaEhQg@mail.gmail.com/
Fixes: 58ef4ece1e ("soc: qcom: pmic_glink: Introduce base PMIC GLINK driver")
Cc: stable@vger.kernel.org
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Tested-by: Amit Pundir <amit.pundir@linaro.org>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Acked-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Tested-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Bjorn Andersson <quic_bjorande@quicinc.com>
Link: https://lore.kernel.org/r/20240820-pmic-glink-v6-11-races-v3-1-eec53c750a04@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In commit b16abab1fb ("usb: typec: tcpm: unregister existing source
caps before re-registration"), quilt, and git, applied the diff to the
incorrect function, which would cause bad problems if exercised in a
device with these capabilities.
Fix this all up (including the follow-up fix in commit 04c05d50fa
("usb: typec: tcpm: fix use-after-free case in
tcpm_register_source_caps") to be in the correct function.
Fixes: 04c05d50fa ("usb: typec: tcpm: fix use-after-free case in tcpm_register_source_caps")
Fixes: b16abab1fb ("usb: typec: tcpm: unregister existing source caps before re-registration")
Reported-by: Charles Yo <charlesyo@google.com>
Cc: Kyle Tso <kyletso@google.com>
Cc: Amit Sunil Dhamne <amitsd@google.com>
Cc: Ondrej Jirman <megi@xff.cz>
Cc: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dddc00f255415b826190cfbaa5d6dbc87cd9ded1 upstream.
This reverts commit 52a39f2cf62bb5430ad1f54cd522dbfdab1d71ba.
Based on review comments, it was applied too soon and needs more work.
Reported-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Link: https://lore.kernel.org/r/20231005081716.GA13853@pendragon.ideasonboard.com
Cc: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 89d7f962994604a3e3d480832788d06179abefc5 ]
On some SoC's like SA8295P where the tertiary controller is host-only
capable, GEVTADDRHI/LO, GEVTSIZ, GEVTCOUNT registers are not accessible.
Trying to access them leads to a crash.
For DRD/Peripheral supported controllers, event buffer setup is done
again in gadget_pullup. Skip setup or cleanup of event buffers if
controller is host-only capable.
Suggested-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Krishna Kurapati <quic_kriskura@quicinc.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Bjorn Andersson <andersson@kernel.org>
Tested-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20240420044901.884098-4-quic_kriskura@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 87850f6cc20911e35eafcbc1d56b0d649ae9162d ]
This fixes a W=1 warning about sprintf writing up to 16 bytes into a
buffer of size 14. There is no practical relevance because there are not
more than 32 endpoints.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/6754df25c56aae04f8110594fad2cd2452b1862a.1708709120.git.u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 52a39f2cf62bb5430ad1f54cd522dbfdab1d71ba ]
The uvc_video_enable function of the uvc-gadget driver is dequeing and
immediately deallocs all requests on its disable codepath. This is not
save since the dequeue function is async and does not ensure that the
requests are left unlinked in the controller driver.
By adding the ep_free_request into the completion path of the requests
we ensure that the request will be properly deallocated.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Link: https://lore.kernel.org/r/20230911140530.2995138-3-m.grzeschik@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit af8e119f52e9c13e556be9e03f27957554a84656 upstream.
re-enumerating full-speed devices after a failed address device command
can trigger a NULL pointer dereference.
Full-speed devices may need to reconfigure the endpoint 0 Max Packet Size
value during enumeration. Usb core calls usb_ep0_reinit() in this case,
which ends up calling xhci_configure_endpoint().
On Panther point xHC the xhci_configure_endpoint() function will
additionally check and reserve bandwidth in software. Other hosts do
this in hardware
If xHC address device command fails then a new xhci_virt_device structure
is allocated as part of re-enabling the slot, but the bandwidth table
pointers are not set up properly here.
This triggers the NULL pointer dereference the next time usb_ep0_reinit()
is called and xhci_configure_endpoint() tries to check and reserve
bandwidth
[46710.713538] usb 3-1: new full-speed USB device number 5 using xhci_hcd
[46710.713699] usb 3-1: Device not responding to setup address.
[46710.917684] usb 3-1: Device not responding to setup address.
[46711.125536] usb 3-1: device not accepting address 5, error -71
[46711.125594] BUG: kernel NULL pointer dereference, address: 0000000000000008
[46711.125600] #PF: supervisor read access in kernel mode
[46711.125603] #PF: error_code(0x0000) - not-present page
[46711.125606] PGD 0 P4D 0
[46711.125610] Oops: Oops: 0000 [#1] PREEMPT SMP PTI
[46711.125615] CPU: 1 PID: 25760 Comm: kworker/1:2 Not tainted 6.10.3_2 #1
[46711.125620] Hardware name: Gigabyte Technology Co., Ltd.
[46711.125623] Workqueue: usb_hub_wq hub_event [usbcore]
[46711.125668] RIP: 0010:xhci_reserve_bandwidth (drivers/usb/host/xhci.c
Fix this by making sure bandwidth table pointers are set up correctly
after a failed address device command, and additionally by avoiding
checking for bandwidth in cases like this where no actual endpoints are
added or removed, i.e. only context for default control endpoint 0 is
evaluated.
Reported-by: Karel Balej <balejk@matfyz.cz>
Closes: https://lore.kernel.org/linux-usb/D3CKQQAETH47.1MUO22RTCH2O3@matfyz.cz/
Cc: stable@vger.kernel.org
Fixes: 651aaf36a7 ("usb: xhci: Handle USB transaction error on address command")
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240815141117.2702314-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 21ea1ce37fc267dc45fe27517bbde926211683df upstream.
This reverts commit bf20c69cf3cf9c6445c4925dd9a8a6ca1b78bfdf.
During tcpm_init() stage, if the VBUS is still present after
tcpm_reset_port(), then we assume that VBUS will off and goto safe0v
after a specific discharge time. Following a TCPM_VBUS_EVENT event if
VBUS reach to off state. TCPM_VBUS_EVENT event may be set during
PORT_RESET handling stage. If pd_events reset to 0 after TCPM_VBUS_EVENT
set, we will lost this VBUS event. Then the port state machine may stuck
at one state.
Before:
[ 2.570172] pending state change PORT_RESET -> PORT_RESET_WAIT_OFF @ 100 ms [rev1 NONE_AMS]
[ 2.570179] state change PORT_RESET -> PORT_RESET_WAIT_OFF [delayed 100 ms]
[ 2.570182] pending state change PORT_RESET_WAIT_OFF -> SNK_UNATTACHED @ 920 ms [rev1 NONE_AMS]
[ 3.490213] state change PORT_RESET_WAIT_OFF -> SNK_UNATTACHED [delayed 920 ms]
[ 3.490220] Start toggling
[ 3.546050] CC1: 0 -> 0, CC2: 0 -> 2 [state TOGGLING, polarity 0, connected]
[ 3.546057] state change TOGGLING -> SRC_ATTACH_WAIT [rev1 NONE_AMS]
After revert this patch, we can see VBUS off event and the port will goto
expected state.
[ 2.441992] pending state change PORT_RESET -> PORT_RESET_WAIT_OFF @ 100 ms [rev1 NONE_AMS]
[ 2.441999] state change PORT_RESET -> PORT_RESET_WAIT_OFF [delayed 100 ms]
[ 2.442002] pending state change PORT_RESET_WAIT_OFF -> SNK_UNATTACHED @ 920 ms [rev1 NONE_AMS]
[ 2.442122] VBUS off
[ 2.442125] state change PORT_RESET_WAIT_OFF -> SNK_UNATTACHED [rev1 NONE_AMS]
[ 2.442127] VBUS VSAFE0V
[ 2.442351] CC1: 0 -> 0, CC2: 0 -> 0 [state SNK_UNATTACHED, polarity 0, disconnected]
[ 2.442357] Start toggling
[ 2.491850] CC1: 0 -> 0, CC2: 0 -> 2 [state TOGGLING, polarity 0, connected]
[ 2.491858] state change TOGGLING -> SRC_ATTACH_WAIT [rev1 NONE_AMS]
[ 2.491863] pending state change SRC_ATTACH_WAIT -> SNK_TRY @ 200 ms [rev1 NONE_AMS]
[ 2.691905] state change SRC_ATTACH_WAIT -> SNK_TRY [delayed 200 ms]
Fixes: bf20c69cf3cf ("usb: typec: tcpm: clear pd_event queue in PORT_RESET")
Cc: stable@vger.kernel.org
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240809112901.535072-1-xu.yang_2@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This bug is found in Zhaoxin platform, but it's a commom code bug.
Fail sequence:
step1: Unbind UHCI controller from native driver;
step2: Bind UHCI controller to vfio-pci, which will put UHCI controller in
one vfio group's device list and set UHCI's dev->driver_data to
struct vfio-pci(for UHCI)
step3: Unbind EHCI controller from native driver, will try to tell UHCI
native driver that "I'm removed by set
companion_hcd->self.hs_companion to NULL. However, companion_hcd
get from UHCI's dev->driver_data that has modified by vfio-pci
already. So, the vfio-pci structure will be damaged!
step4: Bind EHCI controller to vfio-pci driver, which will put EHCI
controller in the same vfio group as UHCI controller;
... ...
step5: Unbind UHCI controller from vfio-pci, which will delete UHCI from
vfio group device list that has been damaged in step 3. So, delete
operation can random result into a NULL pointer dereference with
the below stack dump.
step6: Bind UHCI controller to native driver;
step7: Unbind EHCI controller from vfio-pci, which will try to remove EHCI
controller from the vfio group;
step8: Bind EHCI controller to native driver;
[ 929.114641] uhci_hcd 0000:00:10.0: remove, state 1
[ 929.114652] usb usb1: USB disconnect, device number 1
[ 929.114655] usb 1-1: USB disconnect, device number 2
[ 929.270313] usb 1-2: USB disconnect, device number 3
[ 929.318404] uhci_hcd 0000:00:10.0: USB bus 1 deregistered
[ 929.343029] uhci_hcd 0000:00:10.1: remove, state 4
[ 929.343045] usb usb3: USB disconnect, device number 1
[ 929.343685] uhci_hcd 0000:00:10.1: USB bus 3 deregistered
[ 929.369087] ehci-pci 0000:00:10.7: remove, state 4
[ 929.369102] usb usb4: USB disconnect, device number 1
[ 929.370325] ehci-pci 0000:00:10.7: USB bus 4 deregistered
[ 932.398494] BUG: unable to handle kernel NULL pointer dereference at 0000000000000000
[ 932.398496] PGD 42a67d067 P4D 42a67d067 PUD 42a65f067 PMD 0
[ 932.398502] Oops: 0002 [#2] SMP NOPTI
[ 932.398505] CPU: 2 PID: 7824 Comm: vfio_unbind.sh Tainted: P D 4.19.65-2020051917-rainos #1
[ 932.398506] Hardware name: Shanghai Zhaoxin Semiconductor Co., Ltd. HX002EH/HX002EH,
BIOS HX002EH0_01_R480_R_200408 04/08/2020
[ 932.398513] RIP: 0010:vfio_device_put+0x31/0xa0 [vfio]
[ 932.398515] Code: 89 e5 41 54 53 4c 8b 67 18 48 89 fb 49 8d 74 24 30 e8 e3 0e f3 de
84 c0 74 67 48 8b 53 20 48 8b 43 28 48 8b 7b 18 48 89 42 08 <48> 89 10
48 b8+G26 00 01 00 00 00 00 ad de 48 89 43 20 48 b8 00 02 00
[ 932.398516] RSP: 0018:ffffbbfd04cffc18 EFLAGS: 00010202
[ 932.398518] RAX: 0000000000000000 RBX: ffff92c7ea717880 RCX: 0000000000000000
[ 932.398519] RDX: ffff92c7ea713620 RSI: ffff92c7ea713630 RDI: ffff92c7ea713600
[ 932.398521] RBP: ffffbbfd04cffc28 R08: ffff92c7f02a8080 R09: ffff92c7efc03980
[ 932.398522] R10: ffffbbfd04cff9a8 R11: 0000000000000000 R12: ffff92c7ea713600
[ 932.398523] R13: ffff92c7ed8bb0a8 R14: ffff92c7ea717880 R15: 0000000000000000
[ 932.398525] FS: 00007f3031500740(0000) GS:ffff92c7f0280000(0000) knlGS:0000000000000000
[ 932.398526] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 932.398527] CR2: 0000000000000000 CR3: 0000000428626004 CR4: 0000000000160ee0
[ 932.398528] Call Trace:
[ 932.398534] vfio_del_group_dev+0xe8/0x2a0 [vfio]
[ 932.398539] ? __blocking_notifier_call_chain+0x52/0x60
[ 932.398542] ? do_wait_intr_irq+0x90/0x90
[ 932.398546] ? iommu_bus_notifier+0x75/0x100
[ 932.398551] vfio_pci_remove+0x20/0xa0 [vfio_pci]
[ 932.398554] pci_device_remove+0x3e/0xc0
[ 932.398557] device_release_driver_internal+0x17a/0x240
[ 932.398560] device_release_driver+0x12/0x20
[ 932.398561] unbind_store+0xee/0x180
[ 932.398564] drv_attr_store+0x27/0x40
[ 932.398567] sysfs_kf_write+0x3c/0x50
[ 932.398568] kernfs_fop_write+0x125/0x1a0
[ 932.398572] __vfs_write+0x3a/0x190
[ 932.398575] ? apparmor_file_permission+0x1a/0x20
[ 932.398577] ? security_file_permission+0x3b/0xc0
[ 932.398581] ? _cond_resched+0x1a/0x50
[ 932.398582] vfs_write+0xb8/0x1b0
[ 932.398584] ksys_write+0x5c/0xe0
[ 932.398586] __x64_sys_write+0x1a/0x20
[ 932.398589] do_syscall_64+0x5a/0x110
[ 932.398592] entry_SYSCALL_64_after_hwframe+0x44/0xa9
Using virt-manager/qemu to boot guest os, we can see the same fail sequence!
Fix this by determine whether the PCI Driver of the USB controller is a
kernel native driver. If not, do not let it modify UHCI's dev->driver_data.
Signed-off-by: leoliu-oc <leoliu-oc@zhaoxin.com>
Signed-off-by: Jianping Liu <frankjpliu@tencent.com>
commit 76a7bfc445b8e9893c091e24ccfd4f51dfdc0a70 upstream.
These functions can fail if descriptors are malformed, or missing,
for the selected USB speed.
Fixes: eb9fecb9e6 ("usb: gadget: f_uac2: split out audio core")
Fixes: 24f779dac8 ("usb: gadget: f_uac2/u_audio: add feedback endpoint support")
Cc: stable@vger.kernel.org
Signed-off-by: Chris Wulff <crwulff@gmail.com>
Link: https://lore.kernel.org/r/20240721192314.3532697-2-crwulff@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5a444bea37e2759549ef72bfe83d1c8712e76b3d upstream.
Upstream commit aba3a8d01d ("usb: gadget: u_serial: add suspend
resume callbacks") added started_delayed flag, so that new ports
which are opened after USB suspend can start IO while resuming.
But if the port was already opened, and gadget suspend kicks in
afterwards, start_delayed will never be set. This causes resume
to bail out before calling gs_start_io(). Fix this by setting
start_delayed during suspend.
Fixes: aba3a8d01d ("usb: gadget: u_serial: add suspend resume callbacks")
Cc: stable@vger.kernel.org
Signed-off-by: Prashanth K <quic_prashk@quicinc.com>
Link: https://lore.kernel.org/r/20240730125754.576326-1-quic_prashk@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 228a953e61d6d608a3facc1c3a27b9fb03c99de7 upstream.
When the block number 0xff is given to Function Block Discovery
message, the device should return the information of all Function
Blocks, but currently the gadget driver treats it as an error.
Implement the proper behavior for the block 0xff instead.
Fixes: 8b645922b2 ("usb: gadget: Add support for USB MIDI 2.0 function driver")
Cc: stable@vger.kernel.org
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20240717095102.10493-1-tiwai@suse.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 973a57891608a98e894db2887f278777f564de18 upstream.
Make sure the descriptor has been set before looking at maxpacket.
This fixes a null pointer panic in this case.
This may happen if the gadget doesn't properly set up the endpoint
for the current speed, or the gadget descriptors are malformed and
the descriptor for the speed/endpoint are not found.
No current gadget driver is known to have this problem, but this
may cause a hard-to-find bug during development of new gadgets.
Fixes: 54f83b8c8e ("USB: gadget: Reject endpoints with 0 maxpacket value")
Cc: stable@vger.kernel.org
Signed-off-by: Chris Wulff <crwulff@gmail.com>
Link: https://lore.kernel.org/r/20240725010419.314430-2-crwulff@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 00af4f3dda1461ec90d892edc10bec6d3c50c554 upstream.
This driver is intended as a "client" end of the console connection.
When connected to a host it's supposed to receive debug logs, and
possibly allow to interact with whatever debug console is available
there. Feeding messages back, depending on a configuration may cause log
messages be executed as shell commands (which can be really bad if one
is unlucky, imagine a log message like "prevented running `rm -rf
/home`"). In case of Xen, it exposes sysrq-like debug interface, and
feeding it its own logs will pretty quickly hit 'R' for "instant
reboot".
Contrary to a classic serial console, the USB one cannot be configured
ahead of time, as the device shows up only when target OS is up. And at
the time device is opened to execute relevant ioctl, it's already too
late, especially when logs start flowing shortly after device is
initialized.
Avoid the issue by changing default to no echo for this type of devices.
Signed-off-by: Marek Marczykowski-Górecki <marmarek@invisiblethingslab.com>
[ johan: amend summary; disable also ECHONL ]
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit afdcfd3d6fcdeca2735ca8d994c5f2d24a368f0a upstream.
At a few places the driver carries stale pointers
to references that can still be used. Make sure that does not happen.
This strictly speaking closes ZDI-CAN-22273, though there may be
similar races in the driver.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Cc: stable <stable@kernel.org>
Acked-by: Shuah Khan <skhan@linuxfoundation.org>
Link: https://lore.kernel.org/r/20240709113851.14691-1-oneukum@suse.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 74b64e760ee3433c0f8d95715038c869bcddacf7 ]
Add the missing call to typec_switch_put() when probe fails and
the nb7vpq904m_remove() call is called.
Fixes: 348359e7c2 ("usb: typec: nb7vpq904m: Add an error handling path in nb7vpq904m_probe()")
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Fixes: 88d8f3ac9c ("usb: typec: add support for the nb7vpq904m Type-C Linear Redriver")
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240606-topic-sm8x50-upstream-retimer-broadcast-mode-v2-2-c6f6eae479c3@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 3eb27d3e32c78badbc4db6ae76614b5961e32291 upstream.
The MIDI2 gadget driver handled the default MIDI protocol version
incorrectly due to the confusion of the protocol version passed via
configfs (either 1 or 2) and UMP protocol bits (0x100 / 0x200).
As a consequence, the default protocol always resulted in MIDI1.
This patch addresses the misunderstanding of the protocol handling.
Fixes: 29ee7a4ddd ("usb: gadget: midi2: Add configfs support")
Cc: stable <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20240708095719.25627-1-tiwai@suse.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 79989bd4ab86404743953fa382af0a22900050cf upstream.
Usb device connect may not be detected after runtime resume if
xHC is reset during resume.
In runtime resume cases xhci_resume() will only resume roothubs if there
are pending port events. If the xHC host is reset during runtime resume
due to a Save/Restore Error (SRE) then these pending port events won't be
detected as PORTSC change bits are not immediately set by host after reset.
Unconditionally resume roothubs if xHC is reset during resume to ensure
device connections are detected.
Also return early with error code if starting xHC fails after reset.
Issue was debugged and a similar solution suggested by Remi Pommarel.
Using this instead as it simplifies future refactoring.
Reported-by: Remi Pommarel <repk@triplefau.lt>
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=218987
Suggested-by: Remi Pommarel <repk@triplefau.lt>
Tested-by: Remi Pommarel <repk@triplefau.lt>
Cc: stable@vger.kernel.org
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240627145523.1453155-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a368ecde8a5055b627749b09c6218ef793043e47 upstream.
Syzbot has identified a bug in usbcore (see the Closes: tag below)
caused by our assumption that the reserved bits in an endpoint
descriptor's bEndpointAddress field will always be 0. As a result of
the bug, the endpoint_is_duplicate() routine in config.c (and possibly
other routines as well) may believe that two descriptors are for
distinct endpoints, even though they have the same direction and
endpoint number. This can lead to confusion, including the bug
identified by syzbot (two descriptors with matching endpoint numbers
and directions, where one was interrupt and the other was bulk).
To fix the bug, we will clear the reserved bits in bEndpointAddress
when we parse the descriptor. (Note that both the USB-2.0 and USB-3.1
specs say these bits are "Reserved, reset to zero".) This requires us
to make a copy of the descriptor earlier in usb_parse_endpoint() and
use the copy instead of the original when checking for duplicates.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-and-tested-by: syzbot+8693a0bb9c10b554272a@syzkaller.appspotmail.com
Closes: https://lore.kernel.org/linux-usb/0000000000003d868e061bc0f554@google.com/
Fixes: 0a8fd13462 ("USB: fix problems with duplicate endpoint addresses")
CC: Oliver Neukum <oneukum@suse.com>
CC: stable@vger.kernel.org
Link: https://lore.kernel.org/r/205a5edc-7fef-4159-b64a-80374b6b101a@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6d3c721e686ea6c59e18289b400cc95c76e927e0 upstream.
Userspace provided string 's' could trivially have the length zero. Left
unchecked this will firstly result in an OOB read in the form
`if (str[0 - 1] == '\n') followed closely by an OOB write in the form
`str[0 - 1] = '\0'`.
There is already a validating check to catch strings that are too long.
Let's supply an additional check for invalid strings that are too short.
Signed-off-by: Lee Jones <lee@kernel.org>
Cc: stable <stable@kernel.org>
Link: https://lore.kernel.org/r/20240705074339.633717-1-lee@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3859e85de30815a20bce7db712ce3d94d40a682d upstream.
START BP-850K is a dot matrix printer that crashes when
it receives a Set-Interface request and needs USB_QUIRK_NO_SET_INTF
to work properly.
Cc: stable <stable@kernel.org>
Signed-off-by: jinxiaobo <jinxiaobo@uniontech.com>
Signed-off-by: WangYuli <wangyuli@uniontech.com>
Link: https://lore.kernel.org/r/202E4B2BD0F0FEA4+20240702154408.631201-1-wangyuli@uniontech.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c15a688e49987385baa8804bf65d570e362f8576 upstream.
Since commit c49cfa9170 ("USB: serial: use generic method if no
alternative is provided in usb serial layer"), USB serial core calls the
generic resume implementation when the driver has not provided one.
This can trigger a crash on resume with mos7840 since support for
multiple read URBs was added back in 2011. Specifically, both port read
URBs are now submitted on resume for open ports, but the context pointer
of the second URB is left set to the core rather than mos7840 port
structure.
Fix this by implementing dedicated suspend and resume functions for
mos7840.
Tested with Delock 87414 USB 2.0 to 4x serial adapter.
Signed-off-by: Dmitry Smirnov <d.smirnov@inbox.lv>
[ johan: analyse crash and rewrite commit message; set busy flag on
resume; drop bulk-in check; drop unnecessary usb_kill_urb() ]
Fixes: d83b405383 ("USB: serial: add support for multiple read urbs")
Cc: stable@vger.kernel.org # 3.3
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 9a24eb8010 which is
commit 66cb618bf0bb82859875b00eeffaf223557cb416 upstream.
In backporting it to stable kernels, it causes a severe regression on
many systems, so revert it for now.
Reported-by: Tim Lewis <elatllat@gmail.com>
Link: https://lore.kernel.org/r/CA+3zgmvct7BWib9A7O1ykUf=0nZpdbdpXBdPWOCqfPuyCT3fug@mail.gmail.com
Reported-by: <matthias@bodenbinder.de>
Link: https://lore.kernel.org/r/bug-219039-208809@https.bugzilla.kernel.org/
Cc: Niklas Neronin <niklas.neronin@linux.intel.com>
Cc: Mathias Nyman <mathias.nyman@linux.intel.com>
Cc: Michał Pecio <michal.pecio@gmail.com>
Cc: <ZeroBeat@gmx.de>
Cc: Salvatore Bonaccorso <carnil@debian.org>
Cc: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 66cb618bf0bb82859875b00eeffaf223557cb416 ]
Some transfer events don't always point to a TRB, and consequently don't
have a endpoint ring. In these cases, function handle_tx_event() should
not proceed, because if 'ep->skip' is set, the pointer to the endpoint
ring is used.
To prevent a potential failure and make the code logical, return after
checking the completion code for a Transfer event without TRBs.
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240429140245.3955523-11-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit fc1d1a712b517bbcb383b1f1f7ef478e7d0579f2 upstream.
This is a workaround for STAR 4846132, which only affects
DWC_usb31 version2.00a operating in host mode.
There is a problem in DWC_usb31 version 2.00a operating
in host mode that would cause a CSR read timeout When CSR
read coincides with RAM Clock Gating Entry. By disable
Clock Gating, sacrificing power consumption for normal
operation.
Cc: stable <stable@kernel.org> # 5.10.x: 1e43c86d: usb: dwc3: core: Add DWC31 version 2.00a controller
Signed-off-by: Jos Wang <joswang@lenovo.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20240619114529.3441-1-joswang1221@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8e1ec117efdfd4b2f59f57bd0ad16b4edf5b963f upstream.
Sometimes errors are seen, when doing DR swap, like:
[ 24.672481] ucsi-stm32g0-i2c 0-0035: UCSI_GET_PDOS failed (-5)
[ 24.720188] ucsi-stm32g0-i2c 0-0035: ucsi_handle_connector_change:
GET_CONNECTOR_STATUS failed (-5)
There may be some race, which lead to read CCI, before the command complete
flag is set, hence returning -EIO. Similar fix has been done also in
ucsi_acpi [1].
In case of a spurious or otherwise delayed notification it is
possible that CCI still reports the previous completion. The
UCSI spec is aware of this and provides two completion bits in
CCI, one for normal commands and one for acks. As acks and commands
alternate the notification handler can determine if the completion
bit is from the current command.
To fix this add the ACK_PENDING bit for ucsi_stm32g0 and only complete
commands if the completion bit matches.
[1] https://lore.kernel.org/lkml/20240121204123.275441-3-lk@c--e.de/
Fixes: 72849d4fce ("usb: typec: ucsi: stm32g0: add support for stm32g0 controller")
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com>
Link: https://lore.kernel.org/stable/20240612124656.2305603-1-fabrice.gasnier%40foss.st.com
Cc: stable <stable@kernel.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240612124656.2305603-1-fabrice.gasnier@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c68942624e254a4e8a65afcd3c17ed95acda5489 upstream.
The device_for_each_child_node() macro requires explicit calls to
fwnode_handle_put() in all early exits of the loop if the child node is
not required outside. Otherwise, the child node's refcount is not
decremented and the resource is not released.
The current implementation of pmic_glink_ucsi_probe() makes use of the
device_for_each_child_node(), but does not release the child node on
early returns. Add the missing calls to fwnode_handle_put().
Cc: stable@vger.kernel.org
Fixes: c6165ed2f425 ("usb: ucsi: glink: use the connector orientation GPIO to provide switch events")
Signed-off-by: Javier Carrasco <javier.carrasco.cruz@gmail.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240613-ucsi-glink-release-node-v1-1-f7629a56f70a@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dba7567c2fbbf10a4de2471cdb0e16e5572dc007 upstream.
In the aspeed UDC setup, we configure the UDC hardware with the assigned
USB device address.
However, we have an off-by-one in the bitmask, so we're only setting the
lower 6 bits of the address (USB addresses being 7 bits, and the
hardware bitmask being bits 0:6).
This means that device enumeration fails if the assigned address is
greater than 64:
[ 344.607255] usb 1-1: new high-speed USB device number 63 using ehci-platform
[ 344.808459] usb 1-1: New USB device found, idVendor=cc00, idProduct=cc00, bcdDevice= 6.10
[ 344.817684] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 344.825671] usb 1-1: Product: Test device
[ 344.831075] usb 1-1: Manufacturer: Test vendor
[ 344.836335] usb 1-1: SerialNumber: 00
[ 349.917181] usb 1-1: USB disconnect, device number 63
[ 352.036775] usb 1-1: new high-speed USB device number 64 using ehci-platform
[ 352.249432] usb 1-1: device descriptor read/all, error -71
[ 352.696740] usb 1-1: new high-speed USB device number 65 using ehci-platform
[ 352.909431] usb 1-1: device descriptor read/all, error -71
Use the correct mask of 0x7f (rather than 0x3f), and generate this
through the GENMASK macro, so we have numbers that correspond exactly
to the hardware register definition.
Fixes: 055276c132 ("usb: gadget: add Aspeed ast2600 udc driver")
Cc: stable@vger.kernel.org
Reviewed-by: Neal Liu <neal_liu@aspeedtech.com>
Reviewed-by: Andrew Jeffery <andrew@codeconstruct.com.au>
Signed-off-by: Jeremy Kerr <jk@codeconstruct.com.au>
Link: https://lore.kernel.org/r/20240613-aspeed-udc-v2-1-29501ce9cb7a@codeconstruct.com.au
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7838de15bb700c2898a7d741db9b1f3cbc86c136 upstream.
When config CONFIG_USB_DWC3_DUAL_ROLE is selected, and trigger system
to enter suspend status with below command:
echo mem > /sys/power/state
There will be a deadlock issue occurring. Detailed invoking path as
below:
dwc3_suspend_common()
spin_lock_irqsave(&dwc->lock, flags); <-- 1st
dwc3_gadget_suspend(dwc);
dwc3_gadget_soft_disconnect(dwc);
spin_lock_irqsave(&dwc->lock, flags); <-- 2nd
This issue is exposed by commit c7ebd8149e ("usb: dwc3: gadget: Fix
NULL pointer dereference in dwc3_gadget_suspend") that removes the code
of checking whether dwc->gadget_driver is NULL or not. It causes the
following code is executed and deadlock occurs when trying to get the
spinlock. In fact, the root cause is the commit 5265397f9442("usb: dwc3:
Remove DWC3 locking during gadget suspend/resume") that forgot to remove
the lock of otg mode. So, remove the redundant lock of otg mode during
gadget suspend/resume.
Fixes: 5265397f94 ("usb: dwc3: Remove DWC3 locking during gadget suspend/resume")
Cc: Xu Yang <xu.yang_2@nxp.com>
Cc: stable@vger.kernel.org
Signed-off-by: Meng Li <Meng.Li@windriver.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20240618031918.2585799-1-Meng.Li@windriver.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2eabb655a968b862bc0c31629a09f0fbf3c80d51 upstream.
Syzbot is still reporting quite an old issue [1] that occurs due to
incomplete checking of present usb endpoints. As such, wrong
endpoints types may be used at urb sumbitting stage which in turn
triggers a warning in usb_submit_urb().
Fix the issue by verifying that required endpoint types are present
for both in and out endpoints, taking into account cmd endpoint type.
Unfortunately, this patch has not been tested on real hardware.
[1] Syzbot report:
usb 1-1: BOGUS urb xfer, pipe 1 != type 3
WARNING: CPU: 0 PID: 8667 at drivers/usb/core/urb.c:502 usb_submit_urb+0xed2/0x18a0 drivers/usb/core/urb.c:502
Modules linked in:
CPU: 0 PID: 8667 Comm: kworker/0:4 Not tainted 5.14.0-rc4-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Workqueue: usb_hub_wq hub_event
RIP: 0010:usb_submit_urb+0xed2/0x18a0 drivers/usb/core/urb.c:502
...
Call Trace:
cxacru_cm+0x3c0/0x8e0 drivers/usb/atm/cxacru.c:649
cxacru_card_status+0x22/0xd0 drivers/usb/atm/cxacru.c:760
cxacru_bind+0x7ac/0x11a0 drivers/usb/atm/cxacru.c:1209
usbatm_usb_probe+0x321/0x1ae0 drivers/usb/atm/usbatm.c:1055
cxacru_usb_probe+0xdf/0x1e0 drivers/usb/atm/cxacru.c:1363
usb_probe_interface+0x315/0x7f0 drivers/usb/core/driver.c:396
call_driver_probe drivers/base/dd.c:517 [inline]
really_probe+0x23c/0xcd0 drivers/base/dd.c:595
__driver_probe_device+0x338/0x4d0 drivers/base/dd.c:747
driver_probe_device+0x4c/0x1a0 drivers/base/dd.c:777
__device_attach_driver+0x20b/0x2f0 drivers/base/dd.c:894
bus_for_each_drv+0x15f/0x1e0 drivers/base/bus.c:427
__device_attach+0x228/0x4a0 drivers/base/dd.c:965
bus_probe_device+0x1e4/0x290 drivers/base/bus.c:487
device_add+0xc2f/0x2180 drivers/base/core.c:3354
usb_set_configuration+0x113a/0x1910 drivers/usb/core/message.c:2170
usb_generic_driver_probe+0xba/0x100 drivers/usb/core/generic.c:238
usb_probe_device+0xd9/0x2c0 drivers/usb/core/driver.c:293
Reported-and-tested-by: syzbot+00c18ee8497dd3be6ade@syzkaller.appspotmail.com
Fixes: 902ffc3c70 ("USB: cxacru: Use a bulk/int URB to access the command endpoint")
Cc: stable <stable@kernel.org>
Signed-off-by: Nikita Zhandarovich <n.zhandarovich@fintech.ru>
Link: https://lore.kernel.org/r/20240609131546.3932-1-n.zhandarovich@fintech.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e587a7633dfee8987a999cf253f7c52a8e09276c upstream.
printer_read() and printer_write() guard against the race
against disable() by checking the dev->interface flag,
which in turn is guarded by a spinlock.
These functions, however, drop the lock on multiple occasions.
This means that the test has to be redone after reacquiring
the lock and before doing IO.
Add the tests.
This also addresses CVE-2024-25741
Fixes: 7f2ca14d2f ("usb: gadget: function: printer: Interface is disabled and returns error")
Cc: stable <stable@kernel.org>
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Link: https://lore.kernel.org/r/20240620114039.5767-1-oneukum@suse.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fd80731e5e9d1402cb2f85022a6abf9b1982ec5f upstream.
We need to treat super speed plus as super speed, not the default,
which is full speed.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Cc: stable <stable@kernel.org>
Link: https://lore.kernel.org/r/20240620093800.28901-1-oneukum@suse.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 8bdf8a42bca4f47646fd105a387ab6926948c7f1 ]
It is possible that also the GET_ERROR command fails. If
that happens, the command completion still needs to be
acknowledged. Otherwise the interface will be stuck until
it's reset.
Reported-by: Ammy Yi <ammy.yi@intel.com>
Fixes: bdc62f2bae ("usb: typec: ucsi: Simplified registration and I/O API")
Cc: stable@vger.kernel.org
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20240531104653.1303519-1-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit de52aca4d9d56c3b2f00b638d457075914b1a227 ]
Some PPM implementation do not like UCSI_ACK_CONNECTOR_CHANGE
without UCSI_ACK_COMMAND_COMPLETE. Moreover, doing this is racy
as it requires sending two UCSI_ACK_CC_CI commands in a row and
the second one will be started with UCSI_CCI_ACK_COMPLETE already
set in CCI.
Bundle the UCSI_ACK_CONNECTOR_CHANGE with the UCSI_ACK_COMMAND_COMPLETE
for the UCSI_GET_CONNECTOR_STATUS command that is sent while
handling a connector change event.
Signed-off-by: Christian A. Ehrhardt <lk@c--e.de>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Tested-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20240327224554.1772525-3-lk@c--e.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: 8bdf8a42bca4 ("usb: typec: ucsi: Ack also failed Get Error commands")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 920e7522e3bab5ebc2fb0cc1a034f4470c87fa97 ]
ida_alloc() and ida_free() should be preferred to the deprecated
ida_simple_get() and ida_simple_remove().
Note that the upper limit of ida_simple_get() is exclusive, but the one of
ida_alloc_max() is inclusive. So a -1 has been added when needed.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/7cd361e2b377a5373968fa7deee4169229992a1e.1713107386.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1a395af9d53c6240bf7799abc43b4dc292ca9dd0 ]
Newer Qualcomm platforms (sm8450+) successfully handle busy state and
send the Command Completion after sending the Busy state. Older devices
have firmware bug and can not continue after sending the CCI_BUSY state,
but the command that leads to CCI_BUSY is already forbidden by the
NO_PARTNER_PDOS quirk.
Follow other UCSI glue drivers and drop special handling for CCI_BUSY
event. Let the UCSI core properly handle this state.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240408-qcom-ucsi-fixes-bis-v1-3-716c145ca4b1@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0fb782b5d5c462b2518b3b4fe7d652114c28d613 ]
The Lenovo Yoga Tablet 2 Pro 1380 model is the exception to the rule that
devices which use the Crystal Cove PMIC without using ACPI for battery and
AC power_supply class support use the USB-phy for charger detection.
Unlike the Lenovo Yoga Tablet 2 830 / 1050 models this model has an extra
LC824206XA Micro USB switch which does the charger detection.
Add a DMI quirk to not set the "linux,phy_charger_detect" property on
the 1380 model. This quirk matches on the BIOS version to differentiate
the 1380 model from the 830 and 1050 models which otherwise have
the same DMI strings.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20240406140127.17885-1-hdegoede@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3295f1b866bfbcabd625511968e8a5c541f9ab32 ]
The incompatible device in my possession has a sticker that says
"F5U002 Rev 2" and "P80453-B", and lsusb identifies it as
"050d:0002 Belkin Components IEEE-1284 Controller". There is a bug
report from 2007 from Michael Trausch who was seeing the exact same
errors that I saw in 2024 trying to use this cable.
Link: https://lore.kernel.org/all/46DE5830.9060401@trausch.us/
Signed-off-by: Alex Henrie <alexhenrie24@gmail.com>
Link: https://lore.kernel.org/r/20240326150723.99939-5-alexhenrie24@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f7a7f80ccc8df017507e2b1e1dd652361374d25b ]
When setting the guid via configfs it is possible to test if
its value is one of the kernel supported ones by calling
uvc_format_by_guid on it. If the result is NULL, we know the
guid is unsupported and can be ignored.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Link: https://lore.kernel.org/r/20240221-uvc-gadget-configfs-guid-v1-1-f0678ca62ebb@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 16637fea001ab3c8df528a8995b3211906165a30 ]
The member "uzonesize" of struct alauda_info will remain 0
if alauda_init_media() fails, potentially causing divide errors
in alauda_read_data() and alauda_write_lba().
- Add a member "media_initialized" to struct alauda_info.
- Change a condition in alauda_check_media() to ensure the
first initialization.
- Add an error check for the return value of alauda_init_media().
Fixes: e80b0fade0 ("[PATCH] USB Storage: add alauda support")
Reported-by: xingwei lee <xrivendell7@gmail.com>
Reported-by: yue sun <samsun1006219@gmail.com>
Reviewed-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Shichao Lai <shichaorai@gmail.com>
Link: https://lore.kernel.org/r/20240526012745.2852061-1-shichaorai@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 91f7a1524a92c70ffe264db8bdfa075f15bbbeb9 upstream.
As described in commit 8f873c1ff4 ("xhci: Blacklist using streams on the
Etron EJ168 controller"), EJ188 have the same issue as EJ168, where Streams
do not work reliable on EJ188. So apply XHCI_BROKEN_STREAMS quirk to EJ188
as well.
Cc: stable@vger.kernel.org
Signed-off-by: Kuangyi Chiang <ki.chiang65@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240611120610.3264502-4-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5ceac4402f5d975e5a01c806438eb4e554771577 upstream.
When multiple streams are in use, multiple TDs might be in flight when
an endpoint is stopped. We need to issue a Set TR Dequeue Pointer for
each, to ensure everything is reset properly and the caches cleared.
Change the logic so that any N>1 TDs found active for different streams
are deferred until after the first one is processed, calling
xhci_invalidate_cancelled_tds() again from xhci_handle_cmd_set_deq() to
queue another command until we are done with all of them. Also change
the error/"should never happen" paths to ensure we at least clear any
affected TDs, even if we can't issue a command to clear the hardware
cache, and complain loudly with an xhci_warn() if this ever happens.
This problem case dates back to commit e9df17eb14 ("USB: xhci: Correct
assumptions about number of rings per endpoint.") early on in the XHCI
driver's life, when stream support was first added.
It was then identified but not fixed nor made into a warning in commit
674f8438c1 ("xhci: split handling halted endpoints into two steps"),
which added a FIXME comment for the problem case (without materially
changing the behavior as far as I can tell, though the new logic made
the problem more obvious).
Then later, in commit 94f339147f ("xhci: Fix failure to give back some
cached cancelled URBs."), it was acknowledged again.
[Mathias: commit 94f339147f ("xhci: Fix failure to give back some cached
cancelled URBs.") was a targeted regression fix to the previously mentioned
patch. Users reported issues with usb stuck after unmounting/disconnecting
UAS devices. This rolled back the TD clearing of multiple streams to its
original state.]
Apparently the commit author was aware of the problem (yet still chose
to submit it): It was still mentioned as a FIXME, an xhci_dbg() was
added to log the problem condition, and the remaining issue was mentioned
in the commit description. The choice of making the log type xhci_dbg()
for what is, at this point, a completely unhandled and known broken
condition is puzzling and unfortunate, as it guarantees that no actual
users would see the log in production, thereby making it nigh
undebuggable (indeed, even if you turn on DEBUG, the message doesn't
really hint at there being a problem at all).
It took me *months* of random xHC crashes to finally find a reliable
repro and be able to do a deep dive debug session, which could all have
been avoided had this unhandled, broken condition been actually reported
with a warning, as it should have been as a bug intentionally left in
unfixed (never mind that it shouldn't have been left in at all).
> Another fix to solve clearing the caches of all stream rings with
> cancelled TDs is needed, but not as urgent.
3 years after that statement and 14 years after the original bug was
introduced, I think it's finally time to fix it. And maybe next time
let's not leave bugs unfixed (that are actually worse than the original
bug), and let's actually get people to review kernel commits please.
Fixes xHC crashes and IOMMU faults with UAS devices when handling
errors/faults. Easiest repro is to use `hdparm` to mark an early sector
(e.g. 1024) on a disk as bad, then `cat /dev/sdX > /dev/null` in a loop.
At least in the case of JMicron controllers, the read errors end up
having to cancel two TDs (for two queued requests to different streams)
and the one that didn't get cleared properly ends up faulting the xHC
entirely when it tries to access DMA pages that have since been unmapped,
referred to by the stale TDs. This normally happens quickly (after two
or three loops). After this fix, I left the `cat` in a loop running
overnight and experienced no xHC failures, with all read errors
recovered properly. Repro'd and tested on an Apple M1 Mac Mini
(dwc3 host).
On systems without an IOMMU, this bug would instead silently corrupt
freed memory, making this a security bug (even on systems with IOMMUs
this could silently corrupt memory belonging to other USB devices on the
same controller, so it's still a security bug). Given that the kernel
autoprobes partition tables, I'm pretty sure a malicious USB device
pretending to be a UAS device and reporting an error with the right
timing could deliberately trigger a UAF and write to freed memory, with
no user action.
[Mathias: Commit message and code comment edit, original at:]
https://lore.kernel.org/linux-usb/20240524-xhci-streams-v1-1-6b1f13819bea@marcan.st/
Fixes: e9df17eb14 ("USB: xhci: Correct assumptions about number of rings per endpoint.")
Fixes: 94f339147f ("xhci: Fix failure to give back some cached cancelled URBs.")
Fixes: 674f8438c1 ("xhci: split handling halted endpoints into two steps")
Cc: stable@vger.kernel.org
Cc: security@kernel.org
Reviewed-by: Neal Gompa <neal@gompa.dev>
Signed-off-by: Hector Martin <marcan@marcan.st>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240611120610.3264502-5-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 17bd54555c2aaecfdb38e2734149f684a73fa584 upstream.
As described in commit c877b3b2ad ("xhci: Add reset on resume quirk for
asrock p67 host"), EJ188 have the same issue as EJ168, where completely
dies on resume. So apply XHCI_RESET_ON_RESUME quirk to EJ188 as well.
Cc: stable@vger.kernel.org
Signed-off-by: Kuangyi Chiang <ki.chiang65@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240611120610.3264502-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f0260589b439e2637ad54a2b25f00a516ef28a57 upstream.
The transferred length is set incorrectly for cancelled bulk
transfer TDs in case the bulk transfer ring stops on the last transfer
block with a 'Stop - Length Invalid' completion code.
length essentially ends up being set to the requested length:
urb->actual_length = urb->transfer_buffer_length
Length for 'Stop - Length Invalid' cases should be the sum of all
TRB transfer block lengths up to the one the ring stopped on,
_excluding_ the one stopped on.
Fix this by always summing up TRB lengths for 'Stop - Length Invalid'
bulk cases.
This issue was discovered by Alan Stern while debugging
https://bugzilla.kernel.org/show_bug.cgi?id=218890, but does not
solve that bug. Issue is older than 4.10 kernel but fix won't apply
to those due to major reworks in that area.
Tested-by: Pierre Tomon <pierretom+12@ik.me>
Cc: stable@vger.kernel.org # v4.10+
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240611120610.3264502-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e7e921918d905544500ca7a95889f898121ba886 upstream.
There could be a potential use-after-free case in
tcpm_register_source_caps(). This could happen when:
* new (say invalid) source caps are advertised
* the existing source caps are unregistered
* tcpm_register_source_caps() returns with an error as
usb_power_delivery_register_capabilities() fails
This causes port->partner_source_caps to hold on to the now freed source
caps.
Reset port->partner_source_caps value to NULL after unregistering
existing source caps.
Fixes: 230ecdf71a64 ("usb: typec: tcpm: unregister existing source caps before re-registration")
Cc: stable@vger.kernel.org
Signed-off-by: Amit Sunil Dhamne <amitsd@google.com>
Reviewed-by: Ondrej Jirman <megi@xff.cz>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20240514220134.2143181-1-amitsd@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8475ffcfb381a77075562207ce08552414a80326 upstream.
If no other USB HCDs are selected when compiling a small pure virutal
machine, the Xen HCD driver cannot be built.
Fix it by traversing down host/ if CONFIG_USB_XEN_HCD is selected.
Fixes: 494ed3997d ("usb: Introduce Xen pvUSB frontend (xen hcd)")
Cc: stable@vger.kernel.org # v5.17+
Signed-off-by: John Ernberg <john.ernberg@actia.se>
Link: https://lore.kernel.org/r/20240517114345.1190755-1-john.ernberg@actia.se
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 22f00812862564b314784167a89f27b444f82a46 upstream.
The syzbot fuzzer found that the interrupt-URB completion callback in
the cdc-wdm driver was taking too long, and the driver's immediate
resubmission of interrupt URBs with -EPROTO status combined with the
dummy-hcd emulation to cause a CPU lockup:
cdc_wdm 1-1:1.0: nonzero urb status received: -71
cdc_wdm 1-1:1.0: wdm_int_callback - 0 bytes
watchdog: BUG: soft lockup - CPU#0 stuck for 26s! [syz-executor782:6625]
CPU#0 Utilization every 4s during lockup:
#1: 98% system, 0% softirq, 3% hardirq, 0% idle
#2: 98% system, 0% softirq, 3% hardirq, 0% idle
#3: 98% system, 0% softirq, 3% hardirq, 0% idle
#4: 98% system, 0% softirq, 3% hardirq, 0% idle
#5: 98% system, 1% softirq, 3% hardirq, 0% idle
Modules linked in:
irq event stamp: 73096
hardirqs last enabled at (73095): [<ffff80008037bc00>] console_emit_next_record kernel/printk/printk.c:2935 [inline]
hardirqs last enabled at (73095): [<ffff80008037bc00>] console_flush_all+0x650/0xb74 kernel/printk/printk.c:2994
hardirqs last disabled at (73096): [<ffff80008af10b00>] __el1_irq arch/arm64/kernel/entry-common.c:533 [inline]
hardirqs last disabled at (73096): [<ffff80008af10b00>] el1_interrupt+0x24/0x68 arch/arm64/kernel/entry-common.c:551
softirqs last enabled at (73048): [<ffff8000801ea530>] softirq_handle_end kernel/softirq.c:400 [inline]
softirqs last enabled at (73048): [<ffff8000801ea530>] handle_softirqs+0xa60/0xc34 kernel/softirq.c:582
softirqs last disabled at (73043): [<ffff800080020de8>] __do_softirq+0x14/0x20 kernel/softirq.c:588
CPU: 0 PID: 6625 Comm: syz-executor782 Tainted: G W 6.10.0-rc2-syzkaller-g8867bbd4a056 #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 04/02/2024
Testing showed that the problem did not occur if the two error
messages -- the first two lines above -- were removed; apparently adding
material to the kernel log takes a surprisingly large amount of time.
In any case, the best approach for preventing these lockups and to
avoid spamming the log with thousands of error messages per second is
to ratelimit the two dev_err() calls. Therefore we replace them with
dev_err_ratelimited().
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Suggested-by: Greg KH <gregkh@linuxfoundation.org>
Reported-and-tested-by: syzbot+5f996b83575ef4058638@syzkaller.appspotmail.com
Closes: https://lore.kernel.org/linux-usb/00000000000073d54b061a6a1c65@google.com/
Reported-and-tested-by: syzbot+1b2abad17596ad03dcff@syzkaller.appspotmail.com
Closes: https://lore.kernel.org/linux-usb/000000000000f45085061aa9b37e@google.com/
Fixes: 9908a32e94 ("USB: remove err() macro from usb class drivers")
Link: https://lore.kernel.org/linux-usb/40dfa45b-5f21-4eef-a8c1-51a2f320e267@rowland.harvard.edu/
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/29855215-52f5-4385-b058-91f42c2bee18@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 6309727ef27162deabd5c095c11af24970fba5a2 ]
Add a kthread_stop_put() helper that stops a thread and puts its task
struct. Use it to replace the various instances of kthread_stop()
followed by put_task_struct().
Remove the kthread_stop_put() macro in usbip that is similar but doesn't
return the result of kthread_stop().
[agruenba@redhat.com: fix kerneldoc comment]
Link: https://lkml.kernel.org/r/20230911111730.2565537-1-agruenba@redhat.com
[akpm@linux-foundation.org: document kthread_stop_put()'s argument]
Link: https://lkml.kernel.org/r/20230907234048.2499820-1-agruenba@redhat.com
Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Stable-dep-of: bb9025f4432f ("dma-mapping: benchmark: fix up kthread-related error handling")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 41e1cd1401fcd1f1ae9e47574af2d9fc44a870b3 ]
In a way similar to the previous commit, move
typec_partner_set_usb_power_delivery() to be called after reading the PD
caps. This also removes calls to
usb_power_delivery_unregister_capabilities() from the error path. Keep
all capabilities registered until they are cleared by
ucsi_unregister_partner_pdos().
Fixes: b04e1747fb ("usb: typec: ucsi: Register USB Power Delivery Capabilities")
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240329-qcom-ucsi-fixes-v2-5-0f5d37ed04db@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c0f66d78f42353d38b9608c05f211cf0773d93ac ]
UCSI driver will attempt to set a USB PD device only if it was able to
read PDOs from the firmware. This results in suboptimal behaviour, since
the PD device will be created anyway. Move calls to
typec_port_set_usb_power_delivery() out of conditional code and call it
after reading capabilities.
Fixes: b04e1747fb ("usb: typec: ucsi: Register USB Power Delivery Capabilities")
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240329-qcom-ucsi-fixes-v2-4-0f5d37ed04db@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 409c1cfb5a803f3cf2d17aeaf75c25c4be951b07 upstream.
The current interrupt service routine of the tps6598x only reads the
first 64 bits of the INT_EVENT1 and INT_EVENT2 registers, which means
that any event above that range will be ignored, leaving interrupts
unattended. Moreover, those events will not be cleared, and the device
will keep the interrupt enabled.
This issue has been observed while attempting to load patches, and the
'ReadyForPatch' field (bit 81) of INT_EVENT1 was set.
Given that older versions of the tps6598x (1, 2 and 6) provide 8-byte
registers, a mechanism based on the upper byte of the version register
(0x0F) has been included. The manufacturer has confirmed [1] that this
byte is always 0 for older versions, and either 0xF7 (DH parts) or 0xF9
(DK parts) is returned in newer versions (7 and 8).
Read the complete INT_EVENT registers to handle all interrupts generated
by the device and account for the hardware version to select the
register size.
Link: https://e2e.ti.com/support/power-management-group/power-management/f/power-management-forum/1346521/tps65987d-register-command-to-distinguish-between-tps6591-2-6-and-tps65987-8 [1]
Fixes: 0a4c005bd1 ("usb: typec: driver for TI TPS6598x USB Power Delivery controllers")
Cc: stable@vger.kernel.org
Signed-off-by: Javier Carrasco <javier.carrasco@wolfvision.net>
Link: https://lore.kernel.org/r/20240429-tps6598x_fix_event_handling-v3-2-4e8e58dce489@wolfvision.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b791a67f68121d69108640d4a3e591d210ffe850 upstream.
The function ucsi_displayport_work() does not access the
connector, so it also must not acquire the connector lock.
This fixes a potential deadlock scenario:
ucsi_displayport_work() -> lock(&con->lock)
typec_altmode_vdm()
dp_altmode_vdm()
dp_altmode_work()
typec_altmode_enter()
ucsi_displayport_enter() -> lock(&con->lock)
Reported-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Fixes: af8622f6a5 ("usb: typec: ucsi: Support for DisplayPort alt mode")
Cc: stable@vger.kernel.org
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240507134316.161999-1-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1d26ba0944d398f88aaf997bda3544646cf21945 upstream.
Currently all controller IP/revisions except DWC3_usb3 >= 310a
wait 1ms unconditionally for ENDXFER completion when IOC is not
set. This is because DWC_usb3 controller revisions >= 3.10a
supports GUCTL2[14: Rst_actbitlater] bit which allows polling
CMDACT bit to know whether ENDXFER command is completed.
Consider a case where an IN request was queued, and parallelly
soft_disconnect was called (due to ffs_epfile_release). This
eventually calls stop_active_transfer with IOC cleared, hence
send_gadget_ep_cmd() skips waiting for CMDACT cleared during
EndXfer. For DWC3 controllers with revisions >= 310a, we don't
forcefully wait for 1ms either, and we proceed by unmapping the
requests. If ENDXFER didn't complete by this time, it leads to
SMMU faults since the controller would still be accessing those
requests.
Fix this by ensuring ENDXFER completion by adding 1ms delay in
__dwc3_stop_active_transfer() unconditionally.
Cc: stable@vger.kernel.org
Fixes: b353eb6dc2 ("usb: dwc3: gadget: Skip waiting for CMDACT cleared during endxfer")
Signed-off-by: Prashanth K <quic_prashk@quicinc.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20240502044103.1066350-1-quic_prashk@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ae11f04b452b5205536e1c02d31f8045eba249dd upstream.
typec_register_partner() does not guarantee partner registration
to always succeed. In the event of failure, port->partner is set
to the error value or NULL. Given that port->partner validity is
not checked, this results in the following crash:
Unable to handle kernel NULL pointer dereference at virtual address xx
pc : run_state_machine+0x1bc8/0x1c08
lr : run_state_machine+0x1b90/0x1c08
..
Call trace:
run_state_machine+0x1bc8/0x1c08
tcpm_state_machine_work+0x94/0xe4
kthread_worker_fn+0x118/0x328
kthread+0x1d0/0x23c
ret_from_fork+0x10/0x20
To prevent the crash, check for port->partner validity before
derefencing it in all the call sites.
Cc: stable@vger.kernel.org
Fixes: c97cd0b4b5 ("usb: typec: tcpm: set initial svdm version based on pd revision")
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20240427202812.3435268-1-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bf20c69cf3cf9c6445c4925dd9a8a6ca1b78bfdf upstream.
When a Fast Role Swap control message attempt results in a transition
to ERROR_RECOVERY, the TCPC can still queue a TCPM_SOURCING_VBUS event.
If the event is queued but processed after the tcpm_reset_port() call
in the PORT_RESET state, then the following occurs:
1. tcpm_reset_port() calls tcpm_init_vbus() to reset the vbus sourcing and
sinking state
2. tcpm_pd_event_handler() turns VBUS on before the port is in the default
state.
3. The port resolves as a sink. In the SNK_DISCOVERY state,
tcpm_set_charge() cannot set vbus to charge.
Clear pd events within PORT_RESET to get rid of non-applicable events.
Fixes: b17dd57118 ("staging: typec: tcpm: Improve role swap with non PD capable partners")
Cc: stable@vger.kernel.org
Signed-off-by: RD Babiera <rdbabiera@google.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240423202715.3375827-2-rdbabiera@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6d735722063a945de56472bdc6bfcb170fd43b86 upstream.
GUSB3PIPECTL.SUSPENDENABLE and GUSB2PHYCFG.SUSPHY should be cleared
during initialization. Suspend during initialization can result in
undefined behavior due to clock synchronization failure, which often
seen as core soft reset timeout.
The programming guide recommended these bits to be cleared during
initialization for DWC_usb3.0 version 1.94 and above (along with
DWC_usb31 and DWC_usb32). The current check in the driver does not
account if it's set by default setting from coreConsultant.
This is especially the case for DRD when switching mode to ensure the
phy clocks are available to change mode. Depending on the
platforms/design, some may be affected more than others. This is noted
in the DWC_usb3x programming guide under the above registers.
Let's just disable them during driver load and mode switching. Restore
them when the controller initialization completes.
Note that some platforms workaround this issue by disabling phy suspend
through "snps,dis_u3_susphy_quirk" and "snps,dis_u2_susphy_quirk" when
they should not need to.
Cc: stable@vger.kernel.org
Fixes: 9ba3aca8fe ("usb: dwc3: Disable phy suspend after power-on reset")
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20da4e5a0c4678c9587d3da23f83bdd6d77353e9.1713394973.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4a237d55446ff67655dc3eed2d4a41997536fc4c upstream.
The xhci_plat.h should not need to include the entire xhci.h header.
This can cause redefinition in dwc3 if it selectively includes some xHCI
definitions. This is a prerequisite change for a fix to disable suspend
during initialization for dwc3.
Cc: stable@vger.kernel.org
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/310acfa01c957a10d9feaca3f7206269866ba2eb.1713394973.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0aea736ddb877b93f6d2dd8cf439840d6b4970a9 upstream.
If the USB driver passes a pointer into the TRB buffer for creq, this
buffer can be overwritten with the status response as soon as the event
is queued. This can make the final check return USB_GADGET_DELAYED_STATUS
when it shouldn't. Instead use the stored wLength.
Fixes: 4d644abf25 ("usb: gadget: f_fs: Only return delayed status when len is 0")
Cc: stable <stable@kernel.org>
Signed-off-by: Chris Wulff <chris.wulff@biamp.com>
Link: https://lore.kernel.org/r/CO1PR17MB5419BD664264A558B2395E28E1112@CO1PR17MB5419.namprd17.prod.outlook.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 24729b307eefcd7c476065cd7351c1a018082c19 upstream.
FFS based applications can utilize the aio_cancel() callback to dequeue
pending USB requests submitted to the UDC. There is a scenario where the
FFS application issues an AIO cancel call, while the UDC is handling a
soft disconnect. For a DWC3 based implementation, the callstack looks
like the following:
DWC3 Gadget FFS Application
dwc3_gadget_soft_disconnect() ...
--> dwc3_stop_active_transfers()
--> dwc3_gadget_giveback(-ESHUTDOWN)
--> ffs_epfile_async_io_complete() ffs_aio_cancel()
--> usb_ep_free_request() --> usb_ep_dequeue()
There is currently no locking implemented between the AIO completion
handler and AIO cancel, so the issue occurs if the completion routine is
running in parallel to an AIO cancel call coming from the FFS application.
As the completion call frees the USB request (io_data->req) the FFS
application is also referencing it for the usb_ep_dequeue() call. This can
lead to accessing a stale/hanging pointer.
commit b566d38857 ("usb: gadget: f_fs: use io_data->status consistently")
relocated the usb_ep_free_request() into ffs_epfile_async_io_complete().
However, in order to properly implement locking to mitigate this issue, the
spinlock can't be added to ffs_epfile_async_io_complete(), as
usb_ep_dequeue() (if successfully dequeuing a USB request) will call the
function driver's completion handler in the same context. Hence, leading
into a deadlock.
Fix this issue by moving the usb_ep_free_request() back to
ffs_user_copy_worker(), and ensuring that it explicitly sets io_data->req
to NULL after freeing it within the ffs->eps_lock. This resolves the race
condition above, as the ffs_aio_cancel() routine will not continue
attempting to dequeue a request that has already been freed, or the
ffs_user_copy_work() not freeing the USB request until the AIO cancel is
done referencing it.
This fix depends on
commit b566d38857 ("usb: gadget: f_fs: use io_data->status
consistently")
Fixes: 2e4c7553cd ("usb: gadget: f_fs: add aio support")
Cc: stable <stable@kernel.org> # b566d38857 ("usb: gadget: f_fs: use io_data->status consistently")
Signed-off-by: Wesley Cheng <quic_wcheng@quicinc.com>
Link: https://lore.kernel.org/r/20240409014059.6740-1-quic_wcheng@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 650ae71c80749fc7cb8858c8049f532eaec64410 upstream.
This commit fixes uvc gadget support on 32-bit platforms.
Commit 0df28607c5 ("usb: gadget: uvc: Generalise helper functions for
reuse") introduced a helper function __uvcg_iter_item_entries() to aid
with parsing lists of items on configfs attributes stores. This function
is a generalization of another very similar function, which used a
stack-allocated temporary buffer of fixed size for each item in the list
and used the sizeof() operator to check for potential buffer overruns.
The new function was changed to allocate the now variably sized temp
buffer on heap, but wasn't properly updated to also check for max buffer
size using the computed size instead of sizeof() operator.
As a result, the maximum item size was 7 (plus null terminator) on
64-bit platforms, and 3 on 32-bit ones. While 7 is accidentally just
barely enough, 3 is definitely too small for some of UVC configfs
attributes. For example, dwFrameInteval, specified in 100ns units,
usually has 6-digit item values, e.g. 166666 for 60fps.
Cc: stable@vger.kernel.org
Fixes: 0df28607c5 ("usb: gadget: uvc: Generalise helper functions for reuse")
Signed-off-by: Ivan Avdeev <me@provod.works>
Link: https://lore.kernel.org/r/20240413150124.1062026-1-me@provod.works
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ec6ce7075ef879b91a8710829016005dc8170f17 upstream.
The OS descriptors logic had the high/low byte of w_value inverted, causing
the extended properties to not be accessible for interface != 0.
>From the Microsoft documentation:
https://learn.microsoft.com/en-us/windows-hardware/drivers/usbcon/microsoft-os-1-0-descriptors-specification
OS_Desc_CompatID.doc (w_index = 0x4):
- wValue:
High Byte = InterfaceNumber. InterfaceNumber is set to the number of the
interface or function that is associated with the descriptor, typically
0x00. Because a device can have only one extended compat ID descriptor,
it should ignore InterfaceNumber, regardless of the value, and simply
return the descriptor.
Low Byte = 0. PageNumber is used to retrieve descriptors that are larger
than 64 KB. The header section is 16 bytes, so PageNumber is set to 0 for
this request.
We currently do not support >64KB compat ID descriptors, so verify that the
low byte is 0.
OS_Desc_Ext_Prop.doc (w_index = 0x5):
- wValue:
High byte = InterfaceNumber. The high byte of wValue is set to the number
of the interface or function that is associated with the descriptor.
Low byte = PageNumber. The low byte of wValue is used to retrieve
descriptors that are larger than 64 KB. The header section is 10 bytes, so
PageNumber is set to 0 for this request.
We also don't support >64KB extended properties, so verify that the low byte
is 0 and use the high byte for the interface number.
Fixes: 37a3a53342 ("usb: gadget: OS Feature Descriptors support")
Cc: stable <stable@kernel.org>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Link: https://lore.kernel.org/r/20240404100635.3215340-1-peter@korsgaard.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a4b46d450c49f32e9d4247b421e58083fde304ce upstream.
Testing with KASAN and syzkaller revealed a bug in port.c:disable_store():
usb_hub_to_struct_hub() can return NULL if the hub that the port belongs to
is concurrently removed, but the function does not check for this
possibility before dereferencing the returned value.
It turns out that the first dereference is unnecessary, since hub->intfdev
is the parent of the port device, so it can be changed easily. Adding a
check for hub == NULL prevents further problems.
The same bug exists in the disable_show() routine, and it can be fixed the
same way.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-and-tested-by: Yue Sun <samsun1006219@gmail.com>
Reported-by: xingwei lee <xrivendell7@gmail.com>
Link: https://lore.kernel.org/linux-usb/CAEkJfYON+ry7xPx=AiLR9jzUNT+i_Va68ACajOC3HoacOfL1ig@mail.gmail.com/
Fixes: f061f43d74 ("usb: hub: port: add sysfs entry to switch port power")
CC: Michael Grzeschik <m.grzeschik@pengutronix.de>
CC: stable@vger.kernel.org
Link: https://lore.kernel.org/r/393aa580-15a5-44ca-ad3b-6462461cd313@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fe81f354841641c7f71163b84912b25c169ed8ec upstream.
Testing ohci functionality with qemu's pci-ohci emulation often results
in ohci interface stalls, resulting in hung task timeouts.
The problem is caused by lost interrupts between the emulation and the
Linux kernel code. Additional interrupts raised while the ohci interrupt
handler in Linux is running and before the handler clears the interrupt
status are not handled. The fix for a similar problem in ehci suggests
that the problem is likely caused by edge-triggered MSI interrupts. See
commit 0b60557230 ("usb: ehci: Prevent missed ehci interrupts with
edge-triggered MSI") for details.
Ensure that the ohci interrupt code handles all pending interrupts before
returning to solve the problem.
Cc: Gerd Hoffmann <kraxel@redhat.com>
Cc: David Laight <David.Laight@aculab.com>
Cc: stable@vger.kernel.org
Fixes: 306c54d0ed ("usb: hcd: Try MSI interrupts on PCI devices")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Alan Stern <stern@rowland.harvard.edu>
Reviewed-by: Gerd Hoffmann <kraxel@redhat.com>
Link: https://lore.kernel.org/r/20240429154010.1507366-1-linux@roeck-us.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c78c3644b772e356ca452ae733a3c4de0fb11dc8 upstream.
A virtual SuperSpeed device in the FreeBSD BVCP package
(https://bhyve.npulse.net/) presents an invalid ep0 maxpacket size of 256.
It stopped working with Linux following a recent commit because now we
check these sizes more carefully than before.
Fix this regression by using the bMaxpacketSize0 value in the device
descriptor for SuperSpeed or faster devices, even if it is invalid. This
is a very simple-minded change; we might want to check more carefully for
values that actually make some sense (for instance, no smaller than 64).
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-and-tested-by: Roger Whittaker <roger.whittaker@suse.com>
Closes: https://bugzilla.suse.com/show_bug.cgi?id=1220569
Link: https://lore.kernel.org/linux-usb/9efbd569-7059-4575-983f-0ea30df41871@suse.com/
Fixes: 59cf445754 ("USB: core: Fix oversight in SuperSpeed initialization")
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/4058ac05-237c-4db4-9ecc-5af42bdb4501@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ce4c8d21054ae9396cd759fe6e8157b525616dc4 upstream.
Fix issues when initially checking for a connector change:
- Use the correct connector number not the entire CCI.
- Call ->read under the PPM lock.
- Remove a bogus READ_ONCE.
Fixes: 808a8b9e0b87 ("usb: typec: ucsi: Check for notifications after init")
Cc: stable@kernel.org
Signed-off-by: Christian A. Ehrhardt <lk@c--e.de>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240401210515.1902048-1-lk@c--e.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 808a8b9e0b87bbc72bcc1f7ddfe5d04746e7ce56 upstream.
The completion notification for the final SET_NOTIFICATION_ENABLE
command during initialization can include a connector change
notification. However, at the time this completion notification is
processed, the ucsi struct is not ready to handle this notification.
As a result the notification is ignored and the controller
never sends an interrupt again.
Re-check CCI for a pending connector state change after
initialization is complete. Adjust the corresponding debug
message accordingly.
Fixes: 71a1fa0df2 ("usb: typec: ucsi: Store the notification mask")
Cc: stable@vger.kernel.org
Signed-off-by: Christian A. Ehrhardt <lk@c--e.de>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8550-QRD
Link: https://lore.kernel.org/r/20240320073927.1641788-3-lk@c--e.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6334b8e4553cc69f51e383c9de545082213d785e upstream.
When ncm function is working and then stop usb0 interface for link down,
eth_stop() is called. At this piont, accidentally if usb transport error
should happen in usb_ep_enable(), 'in_ep' and/or 'out_ep' may not be enabled.
After that, ncm_disable() is called to disable for ncm unbind
but gether_disconnect() is never called since 'in_ep' is not enabled.
As the result, ncm object is released in ncm unbind
but 'dev->port_usb' associated to 'ncm->port' is not NULL.
And when ncm bind again to recover netdev, ncm object is reallocated
but usb0 interface is already associated to previous released ncm object.
Therefore, once usb0 interface is up and eth_start_xmit() is called,
released ncm object is dereferrenced and it might cause use-after-free memory.
[function unlink via configfs]
usb0: eth_stop dev->port_usb=ffffff9b179c3200
--> error happens in usb_ep_enable().
NCM: ncm_disable: ncm=ffffff9b179c3200
--> no gether_disconnect() since ncm->port.in_ep->enabled is false.
NCM: ncm_unbind: ncm unbind ncm=ffffff9b179c3200
NCM: ncm_free: ncm free ncm=ffffff9b179c3200 <-- released ncm
[function link via configfs]
NCM: ncm_alloc: ncm alloc ncm=ffffff9ac4f8a000
NCM: ncm_bind: ncm bind ncm=ffffff9ac4f8a000
NCM: ncm_set_alt: ncm=ffffff9ac4f8a000 alt=0
usb0: eth_open dev->port_usb=ffffff9b179c3200 <-- previous released ncm
usb0: eth_start dev->port_usb=ffffff9b179c3200 <--
eth_start_xmit()
--> dev->wrap()
Unable to handle kernel paging request at virtual address dead00000000014f
This patch addresses the issue by checking if 'ncm->netdev' is not NULL at
ncm_disable() to call gether_disconnect() to deassociate 'dev->port_usb'.
It's more reasonable to check 'ncm->netdev' to call gether_connect/disconnect
rather than check 'ncm->port.in_ep->enabled' since it might not be enabled
but the gether connection might be established.
Signed-off-by: Norihiko Hama <Norihiko.Hama@alpsalpine.com>
Cc: stable <stable@kernel.org>
Link: https://lore.kernel.org/r/20240327023550.51214-1-Norihiko.Hama@alpsalpine.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d920a2ed8620be04a3301e1a9c2b7cc1de65f19d upstream.
SanDisks USB3 storage may disapper after system reboot:
usb usb2-port3: link state change
xhci_hcd 0000:00:14.0: clear port3 link state change, portsc: 0x2c0
usb usb2-port3: do warm reset, port only
xhci_hcd 0000:00:14.0: xhci_hub_status_data: stopping usb2 port polling
xhci_hcd 0000:00:14.0: Get port status 2-3 read: 0x2b0, return 0x2b0
usb usb2-port3: not warm reset yet, waiting 50ms
xhci_hcd 0000:00:14.0: Get port status 2-3 read: 0x2f0, return 0x2f0
usb usb2-port3: not warm reset yet, waiting 200ms
...
xhci_hcd 0000:00:14.0: Get port status 2-3 read: 0x6802c0, return 0x7002c0
usb usb2-port3: not warm reset yet, waiting 200ms
xhci_hcd 0000:00:14.0: clear port3 reset change, portsc: 0x4802c0
xhci_hcd 0000:00:14.0: clear port3 warm(BH) reset change, portsc: 0x4002c0
xhci_hcd 0000:00:14.0: clear port3 link state change, portsc: 0x2c0
xhci_hcd 0000:00:14.0: Get port status 2-3 read: 0x2c0, return 0x2c0
usb usb2-port3: not enabled, trying warm reset again...
This is due to the USB device still cause port change event after xHCI is
shuted down:
xhci_hcd 0000:38:00.0: // Setting command ring address to 0xffffe001
xhci_hcd 0000:38:00.0: xhci_resume: starting usb3 port polling.
xhci_hcd 0000:38:00.0: xhci_hub_status_data: stopping usb4 port polling
xhci_hcd 0000:38:00.0: xhci_hub_status_data: stopping usb3 port polling
xhci_hcd 0000:38:00.0: hcd_pci_runtime_resume: 0
xhci_hcd 0000:38:00.0: xhci_shutdown: stopping usb3 port polling.
xhci_hcd 0000:38:00.0: // Halt the HC
xhci_hcd 0000:38:00.0: xhci_shutdown completed - status = 1
xhci_hcd 0000:00:14.0: xhci_shutdown: stopping usb1 port polling.
xhci_hcd 0000:00:14.0: // Halt the HC
xhci_hcd 0000:00:14.0: xhci_shutdown completed - status = 1
xhci_hcd 0000:00:14.0: Get port status 2-3 read: 0x1203, return 0x203
xhci_hcd 0000:00:14.0: set port reset, actual port 2-3 status = 0x1311
xhci_hcd 0000:00:14.0: Get port status 2-3 read: 0x201203, return 0x100203
xhci_hcd 0000:00:14.0: clear port3 reset change, portsc: 0x1203
xhci_hcd 0000:00:14.0: clear port3 warm(BH) reset change, portsc: 0x1203
xhci_hcd 0000:00:14.0: clear port3 link state change, portsc: 0x1203
xhci_hcd 0000:00:14.0: clear port3 connect change, portsc: 0x1203
xhci_hcd 0000:00:14.0: Get port status 2-3 read: 0x1203, return 0x203
usb 2-3: device not accepting address 2, error -108
xhci_hcd 0000:00:14.0: xHCI dying or halted, can't queue_command
xhci_hcd 0000:00:14.0: Set port 2-3 link state, portsc: 0x1203, write 0x11261
xhci_hcd 0000:00:14.0: Get port status 2-3 read: 0x1263, return 0x263
xhci_hcd 0000:00:14.0: set port reset, actual port 2-3 status = 0x1271
xhci_hcd 0000:00:14.0: Get port status 2-3 read: 0x12b1, return 0x2b1
usb usb2-port3: not reset yet, waiting 60ms
ACPI: PM: Preparing to enter system sleep state S5
xhci_hcd 0000:00:14.0: Get port status 2-3 read: 0x12f1, return 0x2f1
usb usb2-port3: not reset yet, waiting 200ms
reboot: Restarting system
The port change event is caused by LPM transition, so disabling LPM at shutdown
to make sure the device is in U0 for warmboot.
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Cc: stable <stable@kernel.org>
Link: https://lore.kernel.org/r/20240305065140.66801-1-kai.heng.feng@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1607830dadeefc407e4956336d9fcd9e9defd810 upstream.
This reverts commit 339f83612f3a569b194680768b22bf113c26a29d.
It has been found to cause problems in a number of Chromebook devices,
so revert the change until it can be brought back in a safe way.
Link: https://lore.kernel.org/r/385a3519-b45d-48c5-a6fd-a3fdb6bec92f@chromium.org
Reported-by:: Aleksander Morgado <aleksandermj@chromium.org>
Fixes: 339f83612f3a ("usb: cdc-wdm: close race between read and workqueue")
Cc: stable <stable@kernel.org>
Cc: Oliver Neukum <oneukum@suse.com>
Cc: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 5a1ccf0c72cf917ff3ccc131d1bb8d19338ffe52 ]
This patch introduces a new USB quirk,
USB_QUIRK_SHORT_SET_ADDRESS_REQ_TIMEOUT, which modifies the timeout value
for the SET_ADDRESS request. The standard timeout for USB request/command
is 5000 ms, as recommended in the USB 3.2 specification (section 9.2.6.1).
However, certain scenarios, such as connecting devices through an APTIV
hub, can lead to timeout errors when the device enumerates as full speed
initially and later switches to high speed during chirp negotiation.
In such cases, USB analyzer logs reveal that the bus suspends for
5 seconds due to incorrect chirp parsing and resumes only after two
consecutive timeout errors trigger a hub driver reset.
Packet(54) Dir(?) Full Speed J(997.100 us) Idle( 2.850 us)
_______| Time Stamp(28 . 105 910 682)
_______|_____________________________________________________________Ch0
Packet(55) Dir(?) Full Speed J(997.118 us) Idle( 2.850 us)
_______| Time Stamp(28 . 106 910 632)
_______|_____________________________________________________________Ch0
Packet(56) Dir(?) Full Speed J(399.650 us) Idle(222.582 us)
_______| Time Stamp(28 . 107 910 600)
_______|_____________________________________________________________Ch0
Packet(57) Dir Chirp J( 23.955 ms) Idle(115.169 ms)
_______| Time Stamp(28 . 108 532 832)
_______|_____________________________________________________________Ch0
Packet(58) Dir(?) Full Speed J (Suspend)( 5.347 sec) Idle( 5.366 us)
_______| Time Stamp(28 . 247 657 600)
_______|_____________________________________________________________Ch0
This 5-second delay in device enumeration is undesirable, particularly
in automotive applications where quick enumeration is crucial
(ideally within 3 seconds).
The newly introduced quirks provide the flexibility to align with a
3-second time limit, as required in specific contexts like automotive
applications.
By reducing the SET_ADDRESS request timeout to 500 ms, the
system can respond more swiftly to errors, initiate rapid recovery, and
ensure efficient device enumeration. This change is vital for scenarios
where rapid smartphone enumeration and screen projection are essential.
To use the quirk, please write "vendor_id:product_id:p" to
/sys/bus/usb/drivers/hub/module/parameter/quirks
For example,
echo "0x2c48:0x0132:p" > /sys/bus/usb/drivers/hub/module/parameters/quirks"
Signed-off-by: Hardik Gajjar <hgajjar@de.adit-jv.com>
Reviewed-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20231027152029.104363-2-hgajjar@de.adit-jv.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a769154c7cac037914ba375ae88aae55b2c853e0 ]
- The HCD address_device callback now accepts a user-defined timeout value
in milliseconds, providing better control over command execution times.
- The default timeout value for the address_device command has been set
to 5000 ms, aligning with the USB 3.2 specification. However, this
timeout can be adjusted as needed.
- The xhci_setup_device function has been updated to accept the timeout
value, allowing it to specify the maximum wait time for the command
operation to complete.
- The hub driver has also been updated to accommodate the newly added
timeout parameter during the SET_ADDRESS request.
Signed-off-by: Hardik Gajjar <hgajjar@de.adit-jv.com>
Reviewed-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20231027152029.104363-1-hgajjar@de.adit-jv.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: 5a1ccf0c72cf ("usb: new quirk to reduce the SET_ADDRESS request timeout")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 12f371e2b6cb4b79c788f1f073992e115f4ca918 ]
Function checkdone is only required if QUIRK2 is defined, so add
appropriate #if / #endif around the function.
Cleans up clang scan build warning:
drivers/usb/host/sl811-hcd.c:588:18: warning: unused function
'checkdone' [-Wunused-function]
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Link: https://lore.kernel.org/r/20240307111351.1982382-1-colin.i.king@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8774ea7a553e2aec323170d49365b59af0a2b7e0 ]
The driver already support the tcpci binding for the i2c_device_id so
add the support for the of_device_id too.
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240222210903.208901-3-m.felsch@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b3db266fb031fba88c423d4bb8983a73a3db6527 ]
Between UCSI 1.2 and UCSI 2.0, the size of the MESSAGE_IN region was
increased from 16 to 256. In order to avoid overflowing reads for older
systems, add a mechanism to use the read UCSI version to truncate read
sizes on UCSI v1.2.
Tested-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Prashant Malani <pmalani@chromium.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Link: https://lore.kernel.org/r/20240209143723.v5.1.Iacf5570a66b82b73ef03daa6557e2fc0db10266a@changeid
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2a3b7af120477d0571b815ccb8600cafd5ebf02f ]
If an frame was transmitted incomplete to the host, we set the
UVC_STREAM_ERR bit in the header for the last request that is going
to be queued. This way the host will know that it should drop the
frame instead of trying to display the corrupted content.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Link: https://lore.kernel.org/r/20240214-uvc-error-tag-v1-2-37659a3877fe@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
driver inclusion
category: bugfix
bugzilla: https://gitee.com/openeuler/kernel/issues/I7ZPUX
CVE: NA
----------------------------------------------------------------------
When the current HiSilicon USB xhci controller formats the faulty
U disk, it will trigger a controller exception error. This will
cause errors in the control logic of the xhci controller and
driver software. In the end, all USB devices on the xhci controller
cannot be used.
By introducing a noop command operation, restore the logic of the
xhci controller and driver software, and restore all USB devices
on the xhci controller to normal.
Signed-off-by: Longfang Liu <liulongfang@huawei.com>
Signed-off-by: JiangShui Yang <yangjiangshui@h-partners.com>
Signed-off-by: Zihao Xue <xuezihao@huawei.com>
[ Upstream commit f5e9bda03aa50ffad36eccafe893d004ef213c43 ]
When orientation switch is enabled in ucsi glink, there is a xhci
probe failure seen when booting up in host mode in reverse
orientation.
During bootup the following things happen in multiple drivers:
a) DWC3 controller driver initializes the core in device mode when the
dr_mode is set to DRD. It relies on role_switch call to change role to
host.
b) QMP driver initializes the lanes to TYPEC_ORIENTATION_NORMAL as a
normal routine. It relies on the typec_switch_set call to get notified
of orientation changes.
c) UCSI core reads the UCSI_GET_CONNECTOR_STATUS via the glink and
provides initial role switch to dwc3 controller.
When booting up in host mode with orientation TYPEC_ORIENTATION_REVERSE,
then we see the following things happening in order:
a) UCSI gives initial role as host to dwc3 controller ucsi_register_port.
Upon receiving this notification, the dwc3 core needs to program GCTL from
PRTCAP_DEVICE to PRTCAP_HOST and as part of this change, it asserts GCTL
Core soft reset and waits for it to be completed before shifting it to
host. Only after the reset is done will the dwc3_host_init be invoked and
xhci is probed. DWC3 controller expects that the usb phy's are stable
during this process i.e., the phy init is already done.
b) During the 100ms wait for GCTL core soft reset, the actual notification
from PPM is received by ucsi_glink via pmic glink for changing role to
host. The pmic_glink_ucsi_notify routine first sends the orientation
change to QMP and then sends role to dwc3 via ucsi framework. This is
happening exactly at the time GCTL core soft reset is being processed.
c) When QMP driver receives typec switch to TYPEC_ORIENTATION_REVERSE, it
then re-programs the phy at the instant GCTL core soft reset has been
asserted by dwc3 controller due to which the QMP PLL lock fails in
qmp_combo_usb_power_on.
d) After the 100ms of GCTL core soft reset is completed, the dwc3 core
goes for initializing the host mode and invokes xhci probe. But at this
point the QMP is non-responsive and as a result, the xhci plat probe fails
during xhci_reset.
Fix this by passing orientation switch to available ucsi instances if
their gpio configuration is available before ucsi_register is invoked so
that by the time, the pmic_glink_ucsi_notify provides typec_switch to QMP,
the lane is already configured and the call would be a NOP thus not racing
with role switch.
Cc: stable@vger.kernel.org
Fixes: c6165ed2f425 ("usb: ucsi: glink: use the connector orientation GPIO to provide switch events")
Suggested-by: Wesley Cheng <quic_wcheng@quicinc.com>
Signed-off-by: Krishna Kurapati <quic_kriskura@quicinc.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240301040914.458492-1-quic_kriskura@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit f121531703ae442edc1dde4b56803680628bc5b7 upstream.
Intel Arrow Lake CPU uses the Meteor Lake ID with this
controller (the controller that's part of the Intel Arrow
Lake chipset (PCH) does still have unique PCI ID).
Fixes: de4b5b28c87c ("usb: dwc3: pci: add support for the Intel Arrow Lake-H")
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20240312115008.1748637-1-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3de4f996a0b5412aa451729008130a488f71563e upstream.
Check the UCSI_CCI_RESET_COMPLETE complete flag before starting
another reset. Use a UCSI_SET_NOTIFICATION_ENABLE command to clear
the flag if it is set.
Signed-off-by: Christian A. Ehrhardt <lk@c--e.de>
Cc: stable <stable@kernel.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8550-QRD
Link: https://lore.kernel.org/r/20240320073927.1641788-6-lk@c--e.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6aaceb7d9cd00f3e065dc4b054ecfe52c5253b03 upstream.
Some DELL systems don't like UCSI_ACK_CC_CI commands with the
UCSI_ACK_CONNECTOR_CHANGE but not the UCSI_ACK_COMMAND_COMPLETE
bit set. The current quirk still leaves room for races because
it requires two consecutive ACK commands to be sent.
Refactor and significantly simplify the quirk to fix this:
Send a dummy command and bundle the connector change ack with the
command completion ack in a single UCSI_ACK_CC_CI command.
This removes the need to probe for the quirk.
While there define flag bits for struct ucsi_acpi->flags in ucsi_acpi.c
and don't re-use definitions from ucsi.h for struct ucsi->flags.
Fixes: f3be347ea42d ("usb: ucsi_acpi: Quirk to ack a connector change ack cmd")
Cc: stable@vger.kernel.org
Signed-off-by: Christian A. Ehrhardt <lk@c--e.de>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8550-QRD
Link: https://lore.kernel.org/r/20240320073927.1641788-5-lk@c--e.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6b5c85ddeea77d18c4b69e3bda60e9374a20c304 upstream.
If a command completes the OPM must send an ack. This applies
to unsupported commands, too.
Send the required ACK for unsupported commands.
Signed-off-by: Christian A. Ehrhardt <lk@c--e.de>
Cc: stable <stable@kernel.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8550-QRD
Link: https://lore.kernel.org/r/20240320073927.1641788-4-lk@c--e.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 15b2e71b4653b3e13df34695a29ebeee237c5af2 upstream.
Suppose we sleep on the PPM lock after clearing the EVENT_PENDING
bit because the thread for another connector is executing a command.
In this case the command completion of the other command will still
report the connector change for our connector.
Clear the EVENT_PENDING bit under the PPM lock to avoid another
useless call to ucsi_handle_connector_change() in this case.
Fixes: c9aed03a0a68 ("usb: ucsi: Add missing ppm_lock")
Cc: stable <stable@kernel.org>
Signed-off-by: Christian A. Ehrhardt <lk@c--e.de>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8550-QRD
Link: https://lore.kernel.org/r/20240320073927.1641788-2-lk@c--e.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 53f5094fdf5deacd99b8655df692e9278506724d upstream.
The attribute writing should return the number of bytes used from the
buffer on success.
Fixes: a7cff92f06 ("usb: typec: USB Power Delivery helpers for ports and partners")
Cc: stable@vger.kernel.org
Signed-off-by: Kyle Tso <kyletso@google.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240319074309.3306579-1-kyletso@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2a587a035214fa1b5ef598aea0b81848c5b72e5e upstream.
It is possible trigger below warning message from mass storage function,
WARNING: CPU: 6 PID: 3839 at drivers/usb/gadget/udc/core.c:294 usb_ep_queue+0x7c/0x104
pc : usb_ep_queue+0x7c/0x104
lr : fsg_main_thread+0x494/0x1b3c
Root cause is mass storage function try to queue request from main thread,
but other thread may already disable ep when function disable.
As there is no function failure in the driver, in order to avoid effort
to fix warning, change WARN_ON_ONCE() in usb_ep_queue() to pr_debug().
Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable@vger.kernel.org
Signed-off-by: yuan linyu <yuanlinyu@hihonor.com>
Reviewed-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20240315020144.2715575-1-yuanlinyu@hihonor.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5d69a3b54e5a630c90d82a4c2bdce3d53dc78710 upstream.
Added functionality to exit from L1 state by device initiation
using remote wakeup signaling, in case when function driver queuing
request while core in L1 state.
Fixes: 273d576c4d ("usb: dwc2: gadget: Add functionality to exit from LPM L1 state")
Fixes: 88b02f2cb1 ("usb: dwc2: Add core state checking")
CC: stable@vger.kernel.org
Signed-off-by: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com>
Link: https://lore.kernel.org/r/b4d9de5382375dddbf7ef6049d9a82066ad87d5d.1710166393.git.Minas.Harutyunyan@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f4d1960764d8a70318b02f15203a1be2b2554ca1 upstream.
The show and store callback routines for the "disable" sysfs attribute
file in port.c acquire the device lock for the port's parent hub
device. This can cause problems if another process has locked the hub
to remove it or change its configuration:
Removing the hub or changing its configuration requires the
hub interface to be removed, which requires the port device
to be removed, and device_del() waits until all outstanding
sysfs attribute callbacks for the ports have returned. The
lock can't be released until then.
But the disable_show() or disable_store() routine can't return
until after it has acquired the lock.
The resulting deadlock can be avoided by calling
sysfs_break_active_protection(). This will cause the sysfs core not
to wait for the attribute's callback routine to return, allowing the
removal to proceed. The disadvantage is that after making this call,
there is no guarantee that the hub structure won't be deallocated at
any moment. To prevent this, we have to acquire a reference to it
first by calling hub_get().
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@kernel.org>
Link: https://lore.kernel.org/r/f7a8c135-a495-4ce6-bd49-405a45e7ea9a@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ee113b860aa169e9a4d2c167c95d0f1961c6e1b8 upstream.
Create hub_get() and hub_put() routines to encapsulate the kref_get()
and kref_put() calls in hub.c. The new routines will be used by the
next patch in this series.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/604da420-ae8a-4a9e-91a4-2d511ff404fb@rowland.harvard.edu
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 80ba43e9f799cbdd83842fc27db667289b3150f5 upstream.
Among the attribute file callback routines in
drivers/usb/core/sysfs.c, the interface_authorized_store() function is
the only one which acquires a device lock on an ancestor device: It
calls usb_deauthorize_interface(), which locks the interface's parent
USB device.
The will lead to deadlock if another process already owns that lock
and tries to remove the interface, whether through a configuration
change or because the device has been disconnected. As part of the
removal procedure, device_del() waits for all ongoing sysfs attribute
callbacks to complete. But usb_deauthorize_interface() can't complete
until the device lock has been released, and the lock won't be
released until the removal has finished.
The mechanism provided by sysfs to prevent this kind of deadlock is
to use the sysfs_break_active_protection() function, which tells sysfs
not to wait for the attribute callback.
Reported-and-tested by: Yue Sun <samsun1006219@gmail.com>
Reported by: xingwei lee <xrivendell7@gmail.com>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/linux-usb/CAEkJfYO6jRVC8Tfrd_R=cjO0hguhrV31fDPrLrNOOHocDkPoAA@mail.gmail.com/#r
Fixes: 310d2b4124 ("usb: interface authorization: SysFS part of USB interface authorization")
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/1c37eea1-9f56-4534-b9d8-b443438dc869@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f9aa41130ac69d13a53ce2a153ca79c70d43f39c upstream.
If the device is configured for system wakeup, then make sure that the
xHCI driver knows about it and make sure to permit wakeup only at the
appropriate time.
For host mode, if the controller goes through the dwc3 code path, then a
child xHCI platform device is created. Make sure the platform device
also inherits the wakeup setting for xHCI to enable remote wakeup.
For device mode, make sure to disable system wakeup if no gadget driver
is bound. We may experience unwanted system wakeup due to the wakeup
signal from the controller PMU detecting connection/disconnection when
in low power (D3). E.g. In the case of Steam Deck, the PCI PME prevents
the system staying in suspend.
Cc: stable@vger.kernel.org
Reported-by: Guilherme G. Piccoli <gpiccoli@igalia.com>
Closes: https://lore.kernel.org/linux-usb/70a7692d-647c-9be7-00a6-06fc60f77294@igalia.com/T/#mf00d6669c2eff7b308d1162acd1d66c09f0853c7
Fixes: d07e8819a0 ("usb: dwc3: add xHCI Host support")
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Tested-by: Sanath S <Sanath.S@amd.com>
Tested-by: Guilherme G. Piccoli <gpiccoli@igalia.com> # Steam Deck
Link: https://lore.kernel.org/r/667cfda7009b502e08462c8fb3f65841d103cc0a.1709865476.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cd5432c712351a3d5f82512908f5febfca946ca6 upstream.
In the scenario of entering hibernation with udisk in the system, if the
udisk was gone or resume fail in the thaw phase of hibernation. Its state
will be set to NOTATTACHED. At this point, usb_hub_wq was already freezed
and can't not handle disconnect event. Next, in the poweroff phase of
hibernation, SYNCHRONIZE_CACHE SCSI command will be sent to this udisk
when poweroff this scsi device, which will cause uas_submit_urbs to be
called to submit URB for sense/data/cmd pipe. However, these URBs will
submit fail as device was set to NOTATTACHED state. Then, uas_submit_urbs
will return a value SCSI_MLQUEUE_DEVICE_BUSY to the caller. That will lead
the SCSI layer go into an ugly loop and system fail to go into hibernation.
On the other hand, when we specially check for -ENODEV in function
uas_queuecommand_lck, returning DID_ERROR to SCSI layer will cause device
poweroff fail and system shutdown instead of entering hibernation.
To fix this issue, let uas_submit_urbs to return original generic error
when submitting URB failed. At the same time, we need to translate -ENODEV
to DID_NOT_CONNECT for the SCSI layer.
Suggested-by: Oliver Neukum <oneukum@suse.com>
Cc: stable@vger.kernel.org
Signed-off-by: Weitao Wang <WeitaoWang-oc@zhaoxin.com>
Link: https://lore.kernel.org/r/20240306180814.4897-1-WeitaoWang-oc@zhaoxin.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 339f83612f3a569b194680768b22bf113c26a29d upstream.
wdm_read() cannot race with itself. However, in
service_outstanding_interrupt() it can race with the
workqueue, which can be triggered by error handling.
Hence we need to make sure that the WDM_RESPONDING
flag is not just only set but tested.
Fixes: afba937e54 ("USB: CDC WDM driver")
Cc: stable <stable@kernel.org>
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Link: https://lore.kernel.org/r/20240314115132.3907-1-oneukum@suse.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fdada0db0b2ae2addef4ccafe50937874dbeeebe upstream.
This reverts commit 75fd6485cccef269ac9eb3b71cf56753341195ef.
This patch was applied twice by accident, causing probe failures.
Revert the accident.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Fixes: 75fd6485ccce ("usb: phy: generic: Get the vbus supply")
Cc: stable <stable@kernel.org>
Reviewed-by: Sean Anderson <sean.anderson@seco.com>
Link: https://lore.kernel.org/r/20240314092628.1869414-1-alexander.stein@ew.tq-group.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b234c70fefa7532d34ebee104de64cc16f1b21e4 upstream.
Ring expansion checker may incorrectly assume a completely full ring
is empty, missing the need for expansion.
This is due to a special empty ring case where the dequeue ends up
ahead of the enqueue pointer. This is seen when enqueued TRBs fill up
exactly a segment, with enqueue then pointing to the end link TRB.
Once those TRBs are handled the dequeue pointer will follow the link
TRB and end up pointing to the first entry on the next segment, past
the enqueue.
This same enqueue - dequeue condition can be true if a ring is full,
with enqueue ending on that last link TRB before the dequeue pointer
on the next segment.
This can be seen when queuing several ~510 small URBs via usbfs in
one go before a single one is handled (i.e. dequeue not moved from first
entry in segment).
Expand the ring already when enqueue reaches the link TRB before the
dequeue segment, instead of expanding it when enqueue moves into the
dequeue segment.
Reported-by: Chris Yokum <linux-usb@mail.totalphase.com>
Closes: https://lore.kernel.org/all/949223224.833962.1709339266739.JavaMail.zimbra@totalphase.com
Tested-by: Chris Yokum <linux-usb@mail.totalphase.com>
Fixes: f5af638f06 ("xhci: Fix transfer ring expansion size calculation")
Cc: stable@vger.kernel.org # v6.5+
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240305132312.955171-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f90ce1e04cbcc76639d6cba0fdbd820cd80b3c70 upstream.
While connecting to a Linux host with CDC_NCM_NTB_DEF_SIZE_TX
set to 65536, it has been observed that we receive short packets,
which come at interval of 5-10 seconds sometimes and have block
length zero but still contain 1-2 valid datagrams present.
According to the NCM spec:
"If wBlockLength = 0x0000, the block is terminated by a
short packet. In this case, the USB transfer must still
be shorter than dwNtbInMaxSize or dwNtbOutMaxSize. If
exactly dwNtbInMaxSize or dwNtbOutMaxSize bytes are sent,
and the size is a multiple of wMaxPacketSize for the
given pipe, then no ZLP shall be sent.
wBlockLength= 0x0000 must be used with extreme care, because
of the possibility that the host and device may get out of
sync, and because of test issues.
wBlockLength = 0x0000 allows the sender to reduce latency by
starting to send a very large NTB, and then shortening it when
the sender discovers that there’s not sufficient data to justify
sending a large NTB"
However, there is a potential issue with the current implementation,
as it checks for the occurrence of multiple NTBs in a single
giveback by verifying if the leftover bytes to be processed is zero
or not. If the block length reads zero, we would process the same
NTB infintely because the leftover bytes is never zero and it leads
to a crash. Fix this by bailing out if block length reads zero.
Cc: stable@vger.kernel.org
Fixes: 427694cfaa ("usb: gadget: ncm: Handle decoding of multiple NTB's in unwrap call")
Signed-off-by: Krishna Kurapati <quic_kriskura@quicinc.com>
Reviewed-by: Maciej Żenczykowski <maze@google.com>
Link: https://lore.kernel.org/r/20240228115441.2105585-1-quic_kriskura@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 165376f6b23e9a779850e750fb2eb06622e5a531 upstream.
The DisplayPort driver's sysfs nodes may be present to the userspace before
typec_altmode_set_drvdata() completes in dp_altmode_probe. This means that
a sysfs read can trigger a NULL pointer error by deferencing dp->hpd in
hpd_show or dp->lock in pin_assignment_show, as dev_get_drvdata() returns
NULL in those cases.
Remove manual sysfs node creation in favor of adding attribute group as
default for devices bound to the driver. The ATTRIBUTE_GROUPS() macro is
not used here otherwise the path to the sysfs nodes is no longer compliant
with the ABI.
Fixes: 0e3bb7d689 ("usb: typec: Add driver for DisplayPort alternate mode")
Cc: stable@vger.kernel.org
Signed-off-by: RD Babiera <rdbabiera@google.com>
Link: https://lore.kernel.org/r/20240229001101.3889432-2-rdbabiera@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 014bcf41d946b36a8f0b8e9b5d9529efbb822f49 upstream.
The isd200 sub-driver in usb-storage uses the HEADS and SECTORS values
in the ATA ID information to calculate cylinder and head values when
creating a CDB for READ or WRITE commands. The calculation involves
division and modulus operations, which will cause a crash if either of
these values is 0. While this never happens with a genuine device, it
could happen with a flawed or subversive emulation, as reported by the
syzbot fuzzer.
Protect against this possibility by refusing to bind to the device if
either the ATA_ID_HEADS or ATA_ID_SECTORS value in the device's ID
information is 0. This requires isd200_Initialization() to return a
negative error code when initialization fails; currently it always
returns 0 (even when there is an error).
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-and-tested-by: syzbot+28748250ab47a8f04100@syzkaller.appspotmail.com
Link: https://lore.kernel.org/linux-usb/0000000000003eb868061245ba7f@google.com/
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Cc: stable@vger.kernel.org
Reviewed-by: PrasannaKumar Muralidharan <prasannatsmkumar@gmail.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Link: https://lore.kernel.org/r/b1e605ea-333f-4ac0-9511-da04f411763e@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 197331b27ac890d0209232d5f669830cd00e8918 upstream.
While commit 69f89168b310 ("usb: typec: tpcm: Fix issues with power being
removed during reset") fixes the boot issues for bus powered devices such
as LibreTech Renegade Elite/Firefly, it trades off the CC pins NOT being
Hi-Zed during errory recovery (i.e PORT_RESET) for devices which are NOT
bus powered(a.k.a self powered). This change Hi-Zs the CC pins only for
self powered devices, thus preventing brown out for bus powered devices
Adhering to spec is gaining more importance due to the Common charger
initiative enforced by the European Union.
Quoting from the spec:
4.5.2.2.2.1 ErrorRecovery State Requirements
The port shall not drive VBUS or VCONN, and shall present a
high-impedance to ground (above zOPEN) on its CC1 and CC2 pins.
Hi-Zing the CC pins is the inteded behavior for PORT_RESET.
CC pins are set to default state after tErrorRecovery in
PORT_RESET_WAIT_OFF.
4.5.2.2.2.2 Exiting From ErrorRecovery State
A Sink shall transition to Unattached.SNK after tErrorRecovery.
A Source shall transition to Unattached.SRC after tErrorRecovery.
Fixes: 69f89168b310 ("usb: typec: tpcm: Fix issues with power being removed during reset")
Cc: stable@vger.kernel.org
Cc: Mark Brown <broonie@kernel.org>
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Tested-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20240228000512.746252-1-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 84fa943d93c31ee978355e6c6c69592dae3c9f59 ]
This commit resolves an issue in the tegra-xudc USB gadget driver that
incorrectly fetched USB3 PHY instances. The problem stemmed from the
assumption of a one-to-one correspondence between USB2 and USB3 PHY
names and their association with physical USB ports in the device tree.
Previously, the driver associated USB3 PHY names directly with the USB3
instance number, leading to mismatches when mapping the physical USB
ports. For instance, if using USB3-1 PHY, the driver expect the
corresponding PHY name as 'usb3-1'. However, the physical USB ports in
the device tree were designated as USB2-0 and USB3-0 as we only have
one device controller, causing a misalignment.
This commit rectifies the issue by adjusting the PHY naming logic.
Now, the driver correctly correlates the USB2 and USB3 PHY instances,
allowing the USB2-0 and USB3-1 PHYs to form a physical USB port pair
while accurately reflecting their configuration in the device tree by
naming them USB2-0 and USB3-0, respectively.
The change ensures that the PHY and PHY names align appropriately,
resolving the mismatch between physical USB ports and their associated
names in the device tree.
Fixes: b4e19931c9 ("usb: gadget: tegra-xudc: Support multiple device modes")
Cc: stable@vger.kernel.org
Signed-off-by: Wayne Chang <waynec@nvidia.com>
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Link: https://lore.kernel.org/r/20240307030328.1487748-3-waynec@nvidia.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6661befe41009c210efa2c1bcd16a5cc4cff8a06 ]
As runtime PM is enabled, the module can be runtime
suspended when .remove() is called.
Do a pm_runtime_get_sync() to make sure module is active
before doing any register operations.
Doing a pm_runtime_put_sync() should disable the refclk
so no need to disable it again.
Fixes the below warning at module removel.
[ 39.705310] ------------[ cut here ]------------
[ 39.710004] clk:162:3 already disabled
[ 39.713941] WARNING: CPU: 0 PID: 921 at drivers/clk/clk.c:1090 clk_core_disable+0xb0/0xb8
We called of_platform_populate() in .probe() so call the
cleanup function of_platform_depopulate() in .remove().
Get rid of the now unnnecessary dwc3_ti_remove_core().
Without this, module re-load doesn't work properly.
Fixes: e8784c0aec ("drivers: usb: dwc3: Add AM62 USB wrapper driver")
Cc: stable@vger.kernel.org # v5.19+
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Link: https://lore.kernel.org/r/20240227-for-v6-9-am62-usb-errata-3-0-v4-1-0ada8ddb0767@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b1a8da9ff1395c4879b4bd41e55733d944f3d613 ]
TDK NC0110013M and MM0110113M have custom USB IDs for CP210x,
so we need to add them to the driver.
Signed-off-by: Toru Katagiri <Toru.Katagiri@tdk.com>
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a0d9d868491a362d421521499d98308c8e3a0398 ]
The radiation meter has the text MGP Instruments PDS-100G or PDS-100GN
produced by Mirion Technologies. Tested by forcing the driver
association with
echo 10c4 863c > /sys/bus/usb-serial/drivers/cp210x/new_id
and then setting the serial port in 115200 8N1 mode. The device
announces ID_USB_VENDOR_ENC=Silicon\x20Labs and ID_USB_MODEL_ENC=PDS100
Signed-off-by: Christian Häggström <christian.haggstrom@orexplore.com>
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3fb7bc4f3a98c48981318b87cf553c5f115fd5ca ]
The GMC IR-USB adapter cable utilizes a FTDI FT232R chip.
Add VID/PID for this adapter so it can be used as serial device via
ftdi_sio.
Signed-off-by: Daniel Vogelbacher <daniel@chaospixel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit be95cc6d71dfd0cba66e3621c65413321b398052 ]
Currently xhci_map_urb_for_dma() creates a temporary buffer and copies
the SG list to the new linear buffer. But if the kzalloc_node() fails,
then the following sg_pcopy_to_buffer() can lead to crash since it
tries to memcpy to NULL pointer.
So return -ENOMEM if kzalloc returns null pointer.
Cc: stable@vger.kernel.org # 5.11
Fixes: 2017a1e584 ("usb: xhci: Use temporary buffer to consolidate SG")
Signed-off-by: Prashanth K <quic_prashk@quicinc.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240229141438.619372-10-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 600556809f04eb3bbccd05218215dcd7b285a9a9 ]
Currently the variable irqflags is being set but is not being used,
it appears it should be used in the call to net2272_probe_fin
rather than IRQF_TRIGGER_LOW being used. Kudos to Uwe Kleine-König
for suggesting the fix.
Cleans up clang scan build warning:
drivers/usb/gadget/udc/net2272.c:2610:15: warning: variable 'irqflags'
set but not used [-Wunused-but-set-variable]
Fixes: ceb80363b2 ("USB: net2272: driver for PLX NET2272 USB device controller")
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20240307181734.2034407-1-colin.i.king@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 75fd6485cccef269ac9eb3b71cf56753341195ef ]
While support for working with a vbus was added, the regulator was never
actually gotten (despite what was documented). Fix this by actually
getting the supply from the device tree.
Fixes: 7acc9973e3 ("usb: phy: generic: add vbus support")
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Link: https://lore.kernel.org/r/20240123225111.1629405-3-sean.anderson@seco.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Upstream: no
EJ188 has similar problems as the upstream
commit a4a251f8c2 ("usb: xhci: do not perform Soft
Retry for some xHCI hosts")
so we add XHCI_NO_SOFT_RETRY quirk for it.
Signed-off-by: Hongchen Zhang <zhanghongchen@loongson.cn>
Signed-off-by: Ming Wang <wangming01@loongson.cn>
commit b787a3e781759026a6212736ef8e52cf83d1821a upstream.
There is a possibility that usb_role_switch device is unregistered before
the user put usb_role_switch. In this case, the user may still want to
get/set_role() since the user can't sense the changes of usb_role_switch.
This will add a flag to show if usb_role_switch is already registered and
avoid unwanted behaviors.
Fixes: fde0aa6c17 ("usb: common: Small class for USB role switches")
cc: stable@vger.kernel.org
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240129093739.2371530-2-xu.yang_2@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1c9be13846c0b2abc2480602f8ef421360e1ad9e upstream.
In current design, usb role class driver will get usb_role_switch parent's
module reference after the user get usb_role_switch device and put the
reference after the user put the usb_role_switch device. However, the
parent device of usb_role_switch may be removed before the user put the
usb_role_switch. If so, then, NULL pointer issue will be met when the user
put the parent module's reference.
This will save the module pointer in structure of usb_role_switch. Then,
we don't need to find module by iterating long relations.
Fixes: 5c54fcac9a ("usb: roles: Take care of driver module reference counting")
cc: stable@vger.kernel.org
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240129093739.2371530-1-xu.yang_2@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 858a74cb512833e276d96a72acb560ce8c138bec upstream.
When upgrading from 6.1 LTS to 6.6 LTS, I noticed the ethernet gadget
stopped working on Palm TE.
Commit 8825acd7cc ("ARM: omap1: remove dead code") deleted Palm TE from
machine_without_vbus_sense(), although the board is still used. Fix that.
Fixes: 8825acd7cc ("ARM: omap1: remove dead code")
Cc: stable <stable@kernel.org>
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20240217192042.GA372205@darkstar.musicnaut.iki.fi
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 76c51146820c5dac629f21deafab0a7039bc3ccd upstream.
It is observed sometimes when tethering is used over NCM with Windows 11
as host, at some instances, the gadget_giveback has one byte appended at
the end of a proper NTB. When the NTB is parsed, unwrap call looks for
any leftover bytes in SKB provided by u_ether and if there are any pending
bytes, it treats them as a separate NTB and parses it. But in case the
second NTB (as per unwrap call) is faulty/corrupt, all the datagrams that
were parsed properly in the first NTB and saved in rx_list are dropped.
Adding a few custom traces showed the following:
[002] d..1 7828.532866: dwc3_gadget_giveback: ep1out:
req 000000003868811a length 1025/16384 zsI ==> 0
[002] d..1 7828.532867: ncm_unwrap_ntb: K: ncm_unwrap_ntb toprocess: 1025
[002] d..1 7828.532867: ncm_unwrap_ntb: K: ncm_unwrap_ntb nth: 1751999342
[002] d..1 7828.532868: ncm_unwrap_ntb: K: ncm_unwrap_ntb seq: 0xce67
[002] d..1 7828.532868: ncm_unwrap_ntb: K: ncm_unwrap_ntb blk_len: 0x400
[002] d..1 7828.532868: ncm_unwrap_ntb: K: ncm_unwrap_ntb ndp_len: 0x10
[002] d..1 7828.532869: ncm_unwrap_ntb: K: Parsed NTB with 1 frames
In this case, the giveback is of 1025 bytes and block length is 1024.
The rest 1 byte (which is 0x00) won't be parsed resulting in drop of
all datagrams in rx_list.
Same is case with packets of size 2048:
[002] d..1 7828.557948: dwc3_gadget_giveback: ep1out:
req 0000000011dfd96e length 2049/16384 zsI ==> 0
[002] d..1 7828.557949: ncm_unwrap_ntb: K: ncm_unwrap_ntb nth: 1751999342
[002] d..1 7828.557950: ncm_unwrap_ntb: K: ncm_unwrap_ntb blk_len: 0x800
Lecroy shows one byte coming in extra confirming that the byte is coming
in from PC:
Transfer 2959 - Bytes Transferred(1025) Timestamp((18.524 843 590)
- Transaction 8391 - Data(1025 bytes) Timestamp(18.524 843 590)
--- Packet 4063861
Data(1024 bytes)
Duration(2.117us) Idle(14.700ns) Timestamp(18.524 843 590)
--- Packet 4063863
Data(1 byte)
Duration(66.160ns) Time(282.000ns) Timestamp(18.524 845 722)
According to Windows driver, no ZLP is needed if wBlockLength is non-zero,
because the non-zero wBlockLength has already told the function side the
size of transfer to be expected. However, there are in-market NCM devices
that rely on ZLP as long as the wBlockLength is multiple of wMaxPacketSize.
To deal with such devices, it pads an extra 0 at end so the transfer is no
longer multiple of wMaxPacketSize.
Cc: <stable@vger.kernel.org>
Fixes: 9f6ce4240a ("usb: gadget: f_ncm.c added")
Signed-off-by: Krishna Kurapati <quic_kriskura@quicinc.com>
Reviewed-by: Maciej Żenczykowski <maze@google.com>
Link: https://lore.kernel.org/r/20240205074650.200304-1-quic_kriskura@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5fd9e45f1ebcd57181358af28506e8a661a260b3 upstream.
829 if (request->complete) {
830 spin_unlock(&priv_dev->lock);
831 usb_gadget_giveback_request(&priv_ep->endpoint,
832 request);
833 spin_lock(&priv_dev->lock);
834 }
835
836 if (request->buf == priv_dev->zlp_buf)
837 cdns3_gadget_ep_free_request(&priv_ep->endpoint, request);
Driver append an additional zero packet request when queue a packet, which
length mod max packet size is 0. When transfer complete, run to line 831,
usb_gadget_giveback_request() will free this requestion. 836 condition is
true, so cdns3_gadget_ep_free_request() free this request again.
Log:
[ 1920.140696][ T150] BUG: KFENCE: use-after-free read in cdns3_gadget_giveback+0x134/0x2c0 [cdns3]
[ 1920.140696][ T150]
[ 1920.151837][ T150] Use-after-free read at 0x000000003d1cd10b (in kfence-#36):
[ 1920.159082][ T150] cdns3_gadget_giveback+0x134/0x2c0 [cdns3]
[ 1920.164988][ T150] cdns3_transfer_completed+0x438/0x5f8 [cdns3]
Add check at line 829, skip call usb_gadget_giveback_request() if it is
additional zero length packet request. Needn't call
usb_gadget_giveback_request() because it is allocated in this driver.
Cc: stable@vger.kernel.org
Fixes: 7733f6c32e ("usb: cdns3: Add Cadence USB3 DRD Driver")
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Acked-by: Peter Chen <peter.chen@kernel.org>
Link: https://lore.kernel.org/r/20240202154217.661867-2-Frank.Li@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 47625b018c6bc788bc10dd654c82696eb0a5ef11 upstream.
Cadence have several controllers from 0x000403xx family but current
driver suuport detecting only one with DID equal 0x0004034E.
It causes that if someone uses different CDNSP controller then driver
will use incorrect version and register space.
Patch fix this issue.
cc: stable@vger.kernel.org
Fixes: 3d82904559 ("usb: cdnsp: cdns3 Add main part of Cadence USBSSP DRD Driver")
Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Link: https://lore.kernel.org/r/20240215121609.259772-1-pawell@cadence.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 18a6be674306c9acb05c08e5c3fd376ef50a917c upstream.
host.c file has some parts of code that were introduced for CDNS3 driver
and should not be used with CDNSP driver.
This patch blocks using these parts of codes by CDNSP driver.
These elements include:
- xhci_plat_cdns3_xhci object
- cdns3 specific XECP_PORT_CAP_REG register
- cdns3 specific XECP_AUX_CTRL_REG1 register
cc: stable@vger.kernel.org
Fixes: 3d82904559 ("usb: cdnsp: cdns3 Add main part of Cadence USBSSP DRD Driver")
Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Link: https://lore.kernel.org/r/20240206104018.48272-1-pawell@cadence.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 23b1d2d99b0f55326f05e7d757fa197c4a95dc5c upstream.
The reverted commit makes the state machine only ever go from SRC_ATTACH_WAIT
to SNK_TRY in endless loop when toggling. After revert it goes to SRC_ATTACHED
after initially trying SNK_TRY earlier, as it should for toggling to ever detect
the power source mode and the port is again able to provide power to attached
power sinks.
This reverts commit 2d6d801270.
Cc: stable@vger.kernel.org
Fixes: 2d6d801270 ("usb: typec: tcpm: reset counter when enter into unattached state after try role")
Signed-off-by: Ondrej Jirman <megi@xff.cz>
Link: https://lore.kernel.org/r/20240217162023.1719738-1-megi@xff.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 321da3dc1f3c92a12e3c5da934090d2992a8814c upstream.
It has been observed that some USB/UAS devices return generic properties
hardcoded in firmware for mode pages for a period of time after a device
has been discovered. The reported properties are either garbage or they do
not accurately reflect the characteristics of the physical storage device
attached in the case of a bridge.
Prior to commit 1e029397d1 ("scsi: sd: Reorganize DIF/DIX code to
avoid calling revalidate twice") we would call revalidate several
times during device discovery. As a result, incorrect values would
eventually get replaced with ones accurately describing the attached
storage. When we did away with the redundant revalidate pass, several
cases were reported where devices reported nonsensical values or would
end up in write-protected state.
An initial attempt at addressing this issue involved introducing a
delayed second revalidate invocation. However, this approach still
left some devices reporting incorrect characteristics.
Tasos Sahanidis debugged the problem further and identified that
introducing a READ operation prior to MODE SENSE fixed the problem and that
it wasn't a timing issue. Issuing a READ appears to cause the devices to
update their state to reflect the actual properties of the storage
media. Device properties like vendor, model, and storage capacity appear to
be correctly reported from the get-go. It is unclear why these devices
defer populating the remaining characteristics.
Match the behavior of a well known commercial operating system and
trigger a READ operation prior to querying device characteristics to
force the device to populate the mode pages.
The additional READ is triggered by a flag set in the USB storage and
UAS drivers. We avoid issuing the READ for other transport classes
since some storage devices identify Linux through our particular
discovery command sequence.
Link: https://lore.kernel.org/r/20240213143306.2194237-1-martin.petersen@oracle.com
Fixes: 1e029397d1 ("scsi: sd: Reorganize DIF/DIX code to avoid calling revalidate twice")
Cc: stable@vger.kernel.org
Reported-by: Tasos Sahanidis <tasos@tasossah.com>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Tested-by: Tasos Sahanidis <tasos@tasossah.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit f3be347ea42dbb0358cd8b2d8dc543a23b70a976 ]
The PPM on some Dell laptops seems to expect that the ACK_CC_CI
command to clear the connector change notification is in turn
followed by another ACK_CC_CI to acknowledge the ACK_CC_CI command
itself. This is in violation of the UCSI spec that states:
"The only notification that is not acknowledged by the OPM is
the command completion notification for the ACK_CC_CI or the
PPM_RESET command."
Add a quirk to send this ack anyway.
Apply the quirk to all Dell systems.
On the first command that acks a connector change send a dummy
command to determine if it runs into a timeout. Only activate
the quirk if it does. This ensure that we do not break Dell
systems that do not need the quirk.
Signed-off-by: "Christian A. Ehrhardt" <lk@c--e.de>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240121204123.275441-4-lk@c--e.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 69f89168b310878be82d7d97bc0d22068ad858c0 upstream.
Since the merge of b717dfbf73e8 ("Revert "usb: typec: tcpm: fix
cc role at port reset"") into mainline the LibreTech Renegade
Elite/Firefly has died during boot, the main symptom observed in testing
is a sudden stop in console output. Gábor Stefanik identified in review
that the patch would cause power to be removed from devices without
batteries (like this board), observing that while the patch is correct
according to the spec this appears to be an oversight in the spec.
Given that the change makes previously working systems unusable let's
revert it, there was some discussion of identifying systems that have
alternative power and implementing the standards conforming behaviour in
only that case.
Fixes: b717dfbf73e8 ("Revert "usb: typec: tcpm: fix cc role at port reset"")
Cc: stable <stable@kernel.org>
Cc: Badhri Jagan Sridharan <badhri@google.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20240212-usb-fix-renegade-v1-1-22c43c88d635@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 61a348857e869432e6a920ad8ea9132e8d44c316 upstream.
In current scenario if Plug-out and Plug-In performed continuously
there could be a chance while checking for dwc->gadget_driver in
dwc3_gadget_suspend, a NULL pointer dereference may occur.
Call Stack:
CPU1: CPU2:
gadget_unbind_driver dwc3_suspend_common
dwc3_gadget_stop dwc3_gadget_suspend
dwc3_disconnect_gadget
CPU1 basically clears the variable and CPU2 checks the variable.
Consider CPU1 is running and right before gadget_driver is cleared
and in parallel CPU2 executes dwc3_gadget_suspend where it finds
dwc->gadget_driver which is not NULL and resumes execution and then
CPU1 completes execution. CPU2 executes dwc3_disconnect_gadget where
it checks dwc->gadget_driver is already NULL because of which the
NULL pointer deference occur.
Cc: stable@vger.kernel.org
Fixes: 9772b47a4c ("usb: dwc3: gadget: Fix suspend/resume during device mode")
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Uttkarsh Aggarwal <quic_uaggarwa@quicinc.com>
Link: https://lore.kernel.org/r/20240119094825.26530-1-quic_uaggarwa@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 12783c0b9e2c7915a50d5ec829630ff2da50472c upstream.
Currently, the function update_port_device_state gets the usb_hub from
udev->parent by calling usb_hub_to_struct_hub.
However, in case the actconfig or the maxchild is 0, the usb_hub would
be NULL and upon further accessing to get port_dev would result in null
pointer dereference.
Fix this by introducing an if check after the usb_hub is populated.
Fixes: 83cb2604f6 ("usb: core: add sysfs entry for usb device state")
Cc: stable@vger.kernel.org
Signed-off-by: Udipto Goswami <quic_ugoswami@quicinc.com>
Reviewed-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20240110095814.7626-1-quic_ugoswami@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cc509b6a47e7c8998d9e41c273191299d5d9d631 upstream.
When power is recycled in usb controller during system power management,
the controller will recognize it and switch role if role has been changed
during power lost. In current design, it will be completed in resume()
function. However, this may bring issues since usb class devices have
their pm operations too and these device's resume() functions are still
not being called at this point. When usb controller recognized host role
should be stopped, these usb class devices will be removed at this point.
But these usb class devices can't be removed in some cases, such as scsi
devices. Since scsi driver may sync data to U-disk, however it will block
there because scsi drvier can only handle pm request when is in suspended
state. Therefore, there may exist a dependency between ci_resume() and usb
class device's resume(). To break this potential dependency, we need to
handle power lost work in a workqueue.
Fixes: 74494b3321 ("usb: chipidea: core: add controller resume support when controller is powered off")
cc: stable@vger.kernel.org
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Link: https://lore.kernel.org/r/20240119123537.3614838-1-xu.yang_2@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b2d2d7ea0dd09802cf5a0545bf54d8ad8987d20c upstream.
When write UDC to empty and unbind gadget driver from gadget device, it is
possible that there are many queue failures for mass storage function.
The root cause is mass storage main thread alaways try to queue request to
receive a command from host if running flag is on, on platform like dwc3,
if pull down called, it will not queue request again and return
-ESHUTDOWN, but it not affect running flag of mass storage function.
Check return code from mass storage function and clear running flag if it
is -ESHUTDOWN, also indicate start in/out transfer failure to break loops.
Cc: stable <stable@kernel.org>
Signed-off-by: yuan linyu <yuanlinyu@hihonor.com>
Reviewed-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20240123034829.3848409-1-yuanlinyu@hihonor.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f17c34ffc792bbb520e4b61baa16b6cfc7d44b13 upstream.
The OTG 1.3 spec has the feature A_ALT_HNP_SUPPORT, which tells
a device that it is connected to the wrong port. Some devices
refuse to operate if you enable that feature, because it indicates
to them that they ought to request to be connected to another port.
According to the spec this feature may be used based only the following
three conditions:
6.5.3 a_alt_hnp_support
Setting this feature indicates to the B-device that it is connected to
an A-device port that is not capable of HNP, but that the A-device does
have an alternate port that is capable of HNP.
The A-device is required to set this feature under the following conditions:
• the A-device has multiple receptacles
• the A-device port that connects to the B-device does not support HNP
• the A-device has another port that does support HNP
A check for the third and first condition is missing. Add it.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Cc: stable <stable@kernel.org>
Fixes: 7d2d641c44 ("usb: otg: don't set a_alt_hnp_support feature for OTG 2.0 device")
Link: https://lore.kernel.org/r/20240122153545.12284-1-oneukum@suse.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2840143e393a4ddc1caab4372969ea337371168c upstream.
In case of a spurious or otherwise delayed notification it is
possible that CCI still reports the previous completion. The
UCSI spec is aware of this and provides two completion bits in
CCI, one for normal commands and one for acks. As acks and commands
alternate the notification handler can determine if the completion
bit is from the current command.
The initial UCSI code correctly handled this but the distinction
between the two completion bits was lost with the introduction of
the new API.
To fix this revive the ACK_PENDING bit for ucsi_acpi and only complete
commands if the completion bit matches.
Fixes: f56de278e8 ("usb: typec: ucsi: acpi: Move to the new API")
Cc: stable@vger.kernel.org
Signed-off-by: "Christian A. Ehrhardt" <lk@c--e.de>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240121204123.275441-3-lk@c--e.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3caf2b2ad7334ef35f55b95f3e1b138c6f77b368 upstream.
The ULPI per-device debugfs root is named after the ulpi device's
parent, but ulpi_unregister_interface tries to remove a debugfs
directory named after the ulpi device itself. This results in the
directory sticking around and preventing subsequent (deferred) probes
from succeeding. Change the directory name to match the ulpi device.
Fixes: bd0a0a024f ("usb: ulpi: Add debugfs support")
Cc: stable@vger.kernel.org
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Link: https://lore.kernel.org/r/20240126223800.2864613-1-sean.anderson@seco.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c9aed03a0a683fd1600ea92f2ad32232d4736272 upstream.
Calling ->sync_write must be done while holding the PPM lock as
the mailbox logic does not support concurrent commands.
At least since the addition of partner task this means that
ucsi_acknowledge_connector_change should be called with the
PPM lock held as it calls ->sync_write.
Thus protect the only call to ucsi_acknowledge_connector_change
with the PPM. All other calls to ->sync_write already happen
under the PPM lock.
Fixes: b9aa02ca39 ("usb: typec: ucsi: Add polling mechanism for partner tasks like alt mode checking")
Cc: stable@vger.kernel.org
Signed-off-by: "Christian A. Ehrhardt" <lk@c--e.de>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240121204123.275441-2-lk@c--e.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7c4650ded49e5b88929ecbbb631efb8b0838e811 upstream.
xHCI 4.9 explicitly forbids assuming that the xHC has released its
ownership of a multi-TRB TD when it reports an error on one of the
early TRBs. Yet the driver makes such assumption and releases the TD,
allowing the remaining TRBs to be freed or overwritten by new TDs.
The xHC should also report completion of the final TRB due to its IOC
flag being set by us, regardless of prior errors. This event cannot
be recognized if the TD has already been freed earlier, resulting in
"Transfer event TRB DMA ptr not part of current TD" error message.
Fix this by reusing the logic for processing isoc Transaction Errors.
This also handles hosts which fail to report the final completion.
Fix transfer length reporting on Babble errors. They may be caused by
device malfunction, no guarantee that the buffer has been filled.
Signed-off-by: Michal Pecio <michal.pecio@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240125152737.2983959-5-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5372c65e1311a16351ef03dd096ff576e6477674 upstream.
The last TRB of a isoc TD might not trigger an event if there was
an error event for a TRB mid TD. This is seen on a NEC Corporation
uPD720200 USB 3.0 Host
After an error mid a multi-TRB TD the xHC should according to xhci 4.9.1
generate events for passed TRBs with IOC flag set if it proceeds to the
next TD. This event is either a copy of the original error, or a
"success" transfer event.
If that event is missing then the driver and xHC host get out of sync as
the driver is still expecting a transfer event for that first TD, while
xHC host is already sending events for the next TD in the list.
This leads to
"Transfer event TRB DMA ptr not part of current TD" messages.
As a solution we tag the isoc TDs that get error events mid TD.
If an event doesn't match the first TD, then check if the tag is
set, and event points to the next TD.
In that case give back the fist TD and process the next TD normally
Make sure TD status and transferred length stay valid in both cases
with and without final TD completion event.
Reported-by: Michał Pecio <michal.pecio@gmail.com>
Closes: https://lore.kernel.org/linux-usb/20240112235205.1259f60c@foxbook/
Tested-by: Michał Pecio <michal.pecio@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240125152737.2983959-4-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 520b391e3e813c1dd142d1eebb3ccfa6d08c3995 upstream.
Upstream commit bac1ec5514 ("usb: xhci: Set quirk for
XHCI_SG_TRB_CACHE_SIZE_QUIRK") introduced a new quirk in XHCI
which fixes XHC timeout, which was seen on synopsys XHCs while
using SG buffers. Currently this quirk can only be set using
xhci private data. But there are some drivers like dwc3/host.c
which adds adds quirks using software node for xhci device.
Hence set this xhci quirk by iterating over device properties.
Cc: stable@vger.kernel.org # 5.11
Fixes: bac1ec5514 ("usb: xhci: Set quirk for XHCI_SG_TRB_CACHE_SIZE_QUIRK")
Signed-off-by: Prashanth K <quic_prashk@quicinc.com>
Link: https://lore.kernel.org/r/20240116055816.1169821-3-quic_prashk@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 817349b6d26aadd8b38283a05ce0bab106b4c765 upstream.
Upstream commit bac1ec5514 ("usb: xhci: Set quirk for
XHCI_SG_TRB_CACHE_SIZE_QUIRK") introduced a new quirk in XHCI
which fixes XHC timeout, which was seen on synopsys XHCs while
using SG buffers. But the support for this quirk isn't present
in the DWC3 layer.
We will encounter this XHCI timeout/hung issue if we run iperf
loopback tests using RTL8156 ethernet adaptor on DWC3 targets
with scatter-gather enabled. This gets resolved after enabling
the XHCI_SG_TRB_CACHE_SIZE_QUIRK. This patch enables it using
the xhci device property since its needed for DWC3 controller.
In Synopsys DWC3 databook,
Table 9-3: xHCI Debug Capability Limitations
Chained TRBs greater than TRB cache size: The debug capability
driver must not create a multi-TRB TD that describes smaller
than a 1K packet that spreads across 8 or more TRBs on either
the IN TR or the OUT TR.
Cc: stable@vger.kernel.org #5.11
Signed-off-by: Prashanth K <quic_prashk@quicinc.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20240116055816.1169821-2-quic_prashk@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b717dfbf73e842d15174699fe2c6ee4fdde8aa1f upstream.
This reverts commit 1e35f07439.
Given that ERROR_RECOVERY calls into PORT_RESET for Hi-Zing
the CC pins, setting CC pins to default state during PORT_RESET
breaks error recovery.
4.5.2.2.2.1 ErrorRecovery State Requirements
The port shall not drive VBUS or VCONN, and shall present a
high-impedance to ground (above zOPEN) on its CC1 and CC2 pins.
Hi-Zing the CC pins is the inteded behavior for PORT_RESET.
CC pins are set to default state after tErrorRecovery in
PORT_RESET_WAIT_OFF.
4.5.2.2.2.2 Exiting From ErrorRecovery State
A Sink shall transition to Unattached.SNK after tErrorRecovery.
A Source shall transition to Unattached.SRC after tErrorRecovery.
Cc: stable@vger.kernel.org
Cc: Frank Wang <frank.wang@rock-chips.com>
Fixes: 1e35f07439 ("usb: typec: tcpm: fix cc role at port reset")
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20240117114742.2587779-1-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 12b17b4eb82a41977eb848048137b5908d52845c upstream.
The device IMST USB-Stick for Smart Meter is a rebranded IMST iM871A-USB
Wireless M-Bus USB-adapter. It is used to read wireless water, gas and
electricity meters.
Signed-off-by: Leonard Dallmayr <leonard.dallmayr@mailbox.org>
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jianping Liu
WangYuli