Currently, ethtool does not expose how many lanes are used when the
link is up.
After adding a possibility to advertise or force a specific number of
lanes, the lanes in use value can be either the maximum width of the port
or below.
Extend ethtool to expose the number of lanes currently in use for
drivers that support it.
For example:
$ ethtool -s swp1 speed 100000 lanes 4
$ ethtool -s swp2 speed 100000 lanes 4
$ ip link set swp1 up
$ ip link set swp2 up
$ ethtool swp1
Settings for swp1:
Supported ports: [ FIBRE Backplane ]
Supported link modes: 1000baseT/Full
10000baseT/Full
1000baseKX/Full
10000baseKR/Full
10000baseR_FEC
40000baseKR4/Full
40000baseCR4/Full
40000baseSR4/Full
40000baseLR4/Full
25000baseCR/Full
25000baseKR/Full
25000baseSR/Full
50000baseCR2/Full
50000baseKR2/Full
100000baseKR4/Full
100000baseSR4/Full
100000baseCR4/Full
100000baseLR4_ER4/Full
50000baseSR2/Full
10000baseCR/Full
10000baseSR/Full
10000baseLR/Full
10000baseER/Full
50000baseKR/Full
50000baseSR/Full
50000baseCR/Full
50000baseLR_ER_FR/Full
50000baseDR/Full
100000baseKR2/Full
100000baseSR2/Full
100000baseCR2/Full
100000baseLR2_ER2_FR2/Full
100000baseDR2/Full
200000baseKR4/Full
200000baseSR4/Full
200000baseLR4_ER4_FR4/Full
200000baseDR4/Full
200000baseCR4/Full
Supported pause frame use: Symmetric Receive-only
Supports auto-negotiation: Yes
Supported FEC modes: Not reported
Advertised link modes: 1000baseT/Full
10000baseT/Full
1000baseKX/Full
1000baseKX/Full
10000baseKR/Full
10000baseR_FEC
40000baseKR4/Full
40000baseCR4/Full
40000baseSR4/Full
40000baseLR4/Full
25000baseCR/Full
25000baseKR/Full
25000baseSR/Full
50000baseCR2/Full
50000baseKR2/Full
100000baseKR4/Full
100000baseSR4/Full
100000baseCR4/Full
100000baseLR4_ER4/Full
50000baseSR2/Full
10000baseCR/Full
10000baseSR/Full
10000baseLR/Full
10000baseER/Full
200000baseKR4/Full
200000baseSR4/Full
200000baseLR4_ER4_FR4/Full
200000baseDR4/Full
200000baseCR4/Full
Advertised pause frame use: No
Advertised auto-negotiation: Yes
Advertised FEC modes: Not reported
Advertised link modes: 100000baseKR4/Full
100000baseSR4/Full
100000baseCR4/Full
100000baseLR4_ER4/Full
Advertised pause frame use: No
Advertised auto-negotiation: Yes
Advertised FEC modes: Not reported
Speed: 100000Mb/s
Lanes: 4
Duplex: Full
Auto-negotiation: on
Port: Direct Attach Copper
PHYAD: 0
Transceiver: internal
Link detected: yes
Signed-off-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: hongrongxuan <hongrongxuan@huawei.com>
Currently, when user space queries the link's parameters, as speed and
duplex, each parameter is passed from the driver to ethtool.
Instead, get the link mode bit in use, and derive each of the parameters
from it in ethtool.
Signed-off-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: hongrongxuan <hongrongxuan@huawei.com>
Conflicts:
net/ethtool/linkmodes.c
Currently, when auto negotiation is on, the user can advertise all the
linkmodes which correspond to a specific speed, but does not have a
similar selector for the number of lanes. This is significant when a
specific speed can be achieved using different number of lanes. For
example, 2x50 or 4x25.
Add 'ETHTOOL_A_LINKMODES_LANES' attribute and expand 'struct
ethtool_link_settings' with lanes field in order to implement a new
lanes-selector that will enable the user to advertise a specific number
of lanes as well.
When auto negotiation is off, lanes parameter can be forced only if the
driver supports it. Add a capability bit in 'struct ethtool_ops' that
allows ethtool know if the driver can handle the lanes parameter when
auto negotiation is off, so if it does not, an error message will be
returned when trying to set lanes.
Example:
$ ethtool -s swp1 lanes 4
$ ethtool swp1
Settings for swp1:
Supported ports: [ FIBRE ]
Supported link modes: 1000baseKX/Full
10000baseKR/Full
40000baseCR4/Full
40000baseSR4/Full
40000baseLR4/Full
25000baseCR/Full
25000baseSR/Full
50000baseCR2/Full
100000baseSR4/Full
100000baseCR4/Full
Supported pause frame use: Symmetric Receive-only
Supports auto-negotiation: Yes
Supported FEC modes: Not reported
Advertised link modes: 40000baseCR4/Full
40000baseSR4/Full
40000baseLR4/Full
100000baseSR4/Full
100000baseCR4/Full
Advertised pause frame use: No
Advertised auto-negotiation: Yes
Advertised FEC modes: Not reported
Speed: Unknown!
Duplex: Unknown! (255)
Auto-negotiation: on
Port: Direct Attach Copper
PHYAD: 0
Transceiver: internal
Link detected: no
Signed-off-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: hongrongxuan <hongrongxuan@huawei.com>
Conflicts:
net/ethtool/linkmodes.c
net/ethtool/netlink.h
Create a new function for input validations to be called before
rtnl_lock() and move the master slave validation to that function.
This would be a cleanup for next patch that would add another validation
to the new function.
Signed-off-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: hongrongxuan <hongrongxuan@huawei.com>
Conflicts:
net/ethtool/linkmodes.c
Currently NIC packet receiving performance based on page pool deteriorates
occasionally. To analysis the causes of this problem page allocation stats
are collected. Here are the stats when NIC rx performance deteriorates:
bandwidth(Gbits/s) 16.8 6.91
rx_pp_alloc_fast 13794308 21141869
rx_pp_alloc_slow 108625 166481
rx_pp_alloc_slow_h 0 0
rx_pp_alloc_empty 8192 8192
rx_pp_alloc_refill 0 0
rx_pp_alloc_waive 100433 158289
rx_pp_recycle_cached 0 0
rx_pp_recycle_cache_full 0 0
rx_pp_recycle_ring 362400 420281
rx_pp_recycle_ring_full 6064893 9709724
rx_pp_recycle_released_ref 0 0
The rx_pp_alloc_waive count indicates that a large number of pages' numa
node are inconsistent with the NIC device numa node. Therefore these pages
can't be reused by the page pool. As a result, many new pages would be
allocated by __page_pool_alloc_pages_slow which is time consuming. This
causes the NIC rx performance fluctuations.
The main reason of huge numa mismatch pages in page pool is that page pool
uses alloc_pages_bulk_array to allocate original pages. This function is
not suitable for page allocation in NUMA scenario. So this patch uses
alloc_pages_bulk_array_node which has a NUMA id input parameter to ensure
the NUMA consistent between NIC device and allocated pages.
Repeated NIC rx performance tests are performed 40 times. NIC rx bandwidth
is higher and more stable compared to the datas above. Here are three test
stats, the rx_pp_alloc_waive count is zero and rx_pp_alloc_slow which
indicates pages allocated from slow patch is relatively low.
bandwidth(Gbits/s) 93 93.9 93.8
rx_pp_alloc_fast 60066264 61266386 60938254
rx_pp_alloc_slow 16512 16517 16539
rx_pp_alloc_slow_ho 0 0 0
rx_pp_alloc_empty 16512 16517 16539
rx_pp_alloc_refill 473841 481910 481585
rx_pp_alloc_waive 0 0 0
rx_pp_recycle_cached 0 0 0
rx_pp_recycle_cache_full 0 0 0
rx_pp_recycle_ring 29754145 30358243 30194023
rx_pp_recycle_ring_full 0 0 0
rx_pp_recycle_released_ref 0 0 0
Signed-off-by: Jie Wang <wangjie125@huawei.com>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Link: https://lore.kernel.org/r/20220705113515.54342-1-huangguangbin2@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: hongrongxuan <hongrongxuan@huawei.com>
Currently If use page pool allocation stats to analysis a RX performance
degradation problem. These stats only count for pages allocate from
page_pool_alloc_pages. But nic drivers such as hns3 use
page_pool_dev_alloc_frag to allocate pages, so page stats in this API
should also be counted.
Signed-off-by: Jie Wang <wangjie125@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: hongrongxuan <hongrongxuan@huawei.com>
Introduce page_pool APIs to report stats through ethtool and reduce
duplicated code in each driver.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: hongrongxuan <hongrongxuan@huawei.com>
Adds a function page_pool_get_stats which can be used by drivers to obtain
stats for a specified page_pool.
Signed-off-by: Joe Damato <jdamato@fastly.com>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: hongrongxuan <hongrongxuan@huawei.com>
Add per-cpu stats tracking page pool recycling events:
- cached: recycling placed page in the page pool cache
- cache_full: page pool cache was full
- ring: page placed into the ptr ring
- ring_full: page released from page pool because the ptr ring was full
- released_refcnt: page released (and not recycled) because refcnt > 1
Signed-off-by: Joe Damato <jdamato@fastly.com>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: hongrongxuan <hongrongxuan@huawei.com>
Add per-pool statistics counters for the allocation path of a page pool.
These stats are incremented in softirq context, so no locking or per-cpu
variables are needed.
This code is disabled by default and a kernel config option is provided for
users who wish to enable them.
The statistics added are:
- fast: successful fast path allocations
- slow: slow path order-0 allocations
- slow_high_order: slow path high order allocations
- empty: ptr ring is empty, so a slow path allocation was forced.
- refill: an allocation which triggered a refill of the cache
- waive: pages obtained from the ptr ring that cannot be added to
the cache due to a NUMA mismatch.
Signed-off-by: Joe Damato <jdamato@fastly.com>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: hongrongxuan <hongrongxuan@huawei.com>
Currently these two checks in ethnl_set_rings are added after rtnl_lock()
which will do useless works if the request is invalid.
So this patch moves these checks before the rtnl_lock() to avoid these
costs.
Signed-off-by: Jie Wang <wangjie125@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: hongrongxuan <hongrongxuan@huawei.com>
Currently tx push is a standard driver feature which controls use of a fast
path descriptor push. So this patch extends the ringparam APIs and data
structures to support set/get tx push by ethtool -G/g.
Signed-off-by: Jie Wang <wangjie125@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: hongrongxuan <hongrongxuan@huawei.com>
Conflicts:
net/ethtool/netlink.h
For applications running on a mix of platforms it's useful
to have a clear indication whether host's NIC supports the
geometry requirements of TCP zero-copy. TCP zero-copy Rx
requires data to be neatly placed into memory pages.
Most NICs can't do that.
This patch is adding GET support only, since the NICs
I work with either always have the feature enabled or
enable it whenever MTU is set to jumbo. In other words
I don't need SET. But adding set should be trivial.
(The only note on SET is that we will likely want
the setting to be "sticky" and use 0 / `unknown`
to reset it back to driver default.)
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: hongrongxuan <hongrongxuan@huawei.com>
Add two new parameters kernel_ringparam and extack for
.get_ringparam and .set_ringparam to extend more ring params
through netlink.
Signed-off-by: Hao Chen <chenhao288@hisilicon.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: hongrongxuan <hongrongxuan@huawei.com>
Conflicts:
drivers/net/can/c_can/c_can_ethtool.c
drivers/net/ethernet/huawei/hinic/hinic_ethtool.c
drivers/net/ethernet/intel/igc/igc_ethtool.c
drivers/net/ethernet/marvell/octeontx2/nic/otx2_ethtool.c
drivers/net/ethernet/mellanox/mlxbf_gige/mlxbf_gige_ethtool.c
drivers/net/ethernet/micrel/ksz884x.c
drivers/net/ethernet/realtek/r8169_main.c
drivers/net/ethernet/sfc/ef100_ethtool.c
drivers/net/ethernet/stmicro/stmmac/stmmac_ethtool.c
drivers/net/ethernet/ti/am65-cpsw-ethtool.c
drivers/net/ethernet/xilinx/ll_temac_main.c
drivers/net/netdevsim/ethtool.c
Add support to set rx buf len via ethtool -G parameter and get
rx buf len via ethtool -g parameter.
Signed-off-by: Hao Chen <chenhao288@hisilicon.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: hongrongxuan <hongrongxuan@huawei.com>
Conflicts:
net/ethtool/netlink.h
net/ethtool/rings.c
Add support for ethtool to set/get tx copybreak buf size.
Signed-off-by: Hao Chen <chenhao288@hisilicon.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: hongrongxuan <hongrongxuan@huawei.com>
stable inclusion
from stable-v5.10.87
commit 7c26da3be1e9843a15b5318f90db8a564479d2ac
bugzilla: 186049 https://gitee.com/openeuler/kernel/issues/I4QVYL
Reference: https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?id=7c26da3be1e9843a15b5318f90db8a564479d2ac
--------------------------------
commit dde91ccfa2 upstream.
There is a short period between a net device starts to be unregistered
and when it is actually gone. In that time frame ethtool operations
could still be performed, which might end up in unwanted or undefined
behaviours[1].
Do not allow ethtool operations after a net device starts its
unregistration. This patch targets the netlink part as the ioctl one
isn't affected: the reference to the net device is taken and the
operation is executed within an rtnl lock section and the net device
won't be found after unregister.
[1] For example adding Tx queues after unregister ends up in NULL
pointer exceptions and UaFs, such as:
BUG: KASAN: use-after-free in kobject_get+0x14/0x90
Read of size 1 at addr ffff88801961248c by task ethtool/755
CPU: 0 PID: 755 Comm: ethtool Not tainted 5.15.0-rc6+ #778
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.14.0-4.fc34 04/014
Call Trace:
dump_stack_lvl+0x57/0x72
print_address_description.constprop.0+0x1f/0x140
kasan_report.cold+0x7f/0x11b
kobject_get+0x14/0x90
kobject_add_internal+0x3d1/0x450
kobject_init_and_add+0xba/0xf0
netdev_queue_update_kobjects+0xcf/0x200
netif_set_real_num_tx_queues+0xb4/0x310
veth_set_channels+0x1c3/0x550
ethnl_set_channels+0x524/0x610
Fixes: 041b1c5d4a ("ethtool: helper functions for netlink interface")
Suggested-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Antoine Tenart <atenart@kernel.org>
Link: https://lore.kernel.org/r/20211203101318.435618-1-atenart@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Chen Jun <chenjun102@huawei.com>
Signed-off-by: Zheng Zengkai <zhengzengkai@huawei.com>
Signed-off-by: hongrongxuan <hongrongxuan@huawei.com>
ethtool_set_coalesce() now uses both the .get_coalesce() and
.set_coalesce() callbacks. But the check for their availability is
buggy, so changing the coalesce settings on a device where the driver
provides only _one_ of the callbacks results in a NULL pointer
dereference instead of an -EOPNOTSUPP.
Fix the condition so that the availability of both callbacks is
ensured. This also matches the netlink code.
Note that reproducing this requires some effort - it only affects the
legacy ioctl path, and needs a specific combination of driver options:
- have .get_coalesce() and .coalesce_supported but no
.set_coalesce(), or
- have .set_coalesce() but no .get_coalesce(). Here eg. ethtool doesn't
cause the crash as it first attempts to call ethtool_get_coalesce()
and bails out on error.
Fixes: f3ccfda193 ("ethtool: extend coalesce setting uAPI with CQE mode")
Cc: Yufeng Mo <moyufeng@huawei.com>
Cc: Huazhong Tan <tanhuazhong@huawei.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Link: https://lore.kernel.org/r/20211126175543.28000-1-jwi@linux.ibm.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: hongrongxuan <hongrongxuan@huawei.com>
In order to support more coalesce parameters through netlink,
add two new parameter kernel_coal and extack for .set_coalesce
and .get_coalesce, then some extra info can return to user with
the netlink API.
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: hongrongxuan <hongrongxuan@huawei.com>
Conflicts:
drivers/net/ethernet/freescale/enetc/enetc_ethtool.c
drivers/net/ethernet/hisilicon/hns3/hns3_ethtool.c
drivers/net/ethernet/huawei/hinic/hinic_ethtool.c
drivers/net/ethernet/intel/igc/igc_ethtool.c
drivers/net/ethernet/marvell/octeontx2/nic/otx2_ethtool.c
drivers/net/ethernet/qlogic/qede/qede.h
drivers/net/ethernet/qlogic/qede/qede_ethtool.c
drivers/net/ethernet/stmicro/stmmac/stmmac_ethtool.c
drivers/net/ethernet/ti/cpsw_new.c
drivers/net/ethernet/xilinx/ll_temac_main.c
drivers/net/netdevsim/ethtool.c
drivers/net/wireless/ath/wil6210/ethtool.c
drivers/s390/net/qeth_ethtool.c
drivers/staging/qlge/qlge_ethtool.c
Currently, there are many drivers who support CQE mode configuration,
some configure it as a fixed when initialized, some provide an
interface to change it by ethtool private flags. In order to make it
more generic, add two new 'ETHTOOL_A_COALESCE_USE_CQE_TX' and
'ETHTOOL_A_COALESCE_USE_CQE_RX' coalesce attributes, then these
parameters can be accessed by ethtool netlink coalesce uAPI.
Also add an new structure kernel_ethtool_coalesce, then the
new parameter can be added into this struct.
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: hongrongxuan <hongrongxuan@huawei.com>
Conflicts:
net/ethtool/coalesce.c
net/ethtool/netlink.h
include/linux/ethtool.h
There has been a few errors in the ethtool reply size calculations,
most of those are hard to trigger during basic testing because of
skb size rounding up and netdev names being shorter than max.
Add a more precise check.
This change will affect the value of payload length displayed in
case of -EMSGSIZE but that should be okay, "payload length" isn't
a well defined term here.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: hongrongxuan <hongrongxuan@huawei.com>
Outer nest for ETHTOOL_A_STRSET_STRINGSETS is not accounted for.
This may result in ETHTOOL_MSG_STRSET_GET producing a warning like:
calculated message payload length (684) not sufficient
WARNING: CPU: 0 PID: 30967 at net/ethtool/netlink.c:369 ethnl_default_doit+0x87a/0xa20
and a splat.
As usually with such warnings three conditions must be met for the warning
to trigger:
- there must be no skb size rounding up (e.g. reply_size of 684);
- string set must be per-device (so that the header gets populated);
- the device name must be at least 12 characters long.
all in all with current user space it looks like reading priv flags
is the only place this could potentially happen. Or with syzbot :)
Reported-by: syzbot+59aa77b92d06cd5a54f2@syzkaller.appspotmail.com
Fixes: 71921690f9 ("ethtool: provide string sets with STRSET_GET request")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: hongrongxuan <hongrongxuan@huawei.com>
When dumping the ethtool information from all the interfaces, the
netlink reply should contain the NLM_F_MULTI flag. This flag allows
userspace tools to identify that multiple messages are expected.
Link: https://bugzilla.redhat.com/1953847
Fixes: 365f9ae4ee ("ethtool: fix genlmsg_put() failure handling in ethnl_default_dumpit()")
Signed-off-by: Fernando Fernandez Mancera <ffmancera@riseup.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: hongrongxuan <hongrongxuan@huawei.com>
Dan points out we need to use the mask not the bit (which is 0).
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Fixes: 42ce127d98 ("ethtool: fec: sanitize ethtool_fecparam->fec")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: hongrongxuan <hongrongxuan@huawei.com>
Reject NONE on set, this mode means device does not support
FEC so it's a little out of place in the set interface.
This should be safe to do - user space ethtool does not allow
the use of NONE on set. A few drivers treat it the same as OFF,
but none use it instead of OFF.
Similarly reject an empty FEC mask. The common user space tool
will not send such requests and most drivers correctly reject
it already.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: hongrongxuan <hongrongxuan@huawei.com>
struct ethtool_fecparam::active_fec is a GET-only field,
all in-tree drivers correctly ignore it on SET. Clear
the field on SET to avoid any confusion. Again, we can't
reject non-zero now since ethtool user space does not
zero-init the param correctly.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: hongrongxuan <hongrongxuan@huawei.com>
struct ethtool_fecparam::reserved is never looked at by the core.
Make sure it's actually 0. Unfortunately we can't return an error
because old ethtool doesn't zero-initialize the structure for SET.
On GET we can be more verbose, there are no in tree (ab)users.
Fix up the kdoc on the structure. Remove the mention of FEC
bypass. Seems like a niche thing to configure in the first
place.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: hongrongxuan <hongrongxuan@huawei.com>
Syzbot reported a shift of a u32 by more than 31 in strset_parse_request()
which is undefined behavior. This is caused by range check of string set id
using variable ret (which is always 0 at this point) instead of id (string
set id from request).
Fixes: 71921690f9 ("ethtool: provide string sets with STRSET_GET request")
Reported-by: syzbot+96523fb438937cd01220@syzkaller.appspotmail.com
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Link: https://lore.kernel.org/r/b54ed5c5fd972a59afea3e1badfb36d86df68799.1607952208.git.mkubecek@suse.cz
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: hongrongxuan <hongrongxuan@huawei.com>
Syzbot reported a stack overflow in bitmap_from_arr32() called from
ethnl_parse_bitset() when bitset from netlink message is longer than
target bitmap length. While ethnl_compact_sanity_checks() makes sure that
trailing part is all zeros (i.e. the request does not try to touch bits
kernel does not recognize), we also need to cap change_bits to nbits so
that we don't try to write past the prepared bitmaps.
Fixes: 88db6d1e4f ("ethtool: add ethnl_parse_bitset() helper")
Reported-by: syzbot+9d39fa49d4df294aab93@syzkaller.appspotmail.com
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Link: https://lore.kernel.org/r/3487ee3a98e14cd526f55b6caaa959d2dcbcad9f.1607465316.git.mkubecek@suse.cz
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: hongrongxuan <hongrongxuan@huawei.com>
A semicolon is not needed after a switch statement.
Signed-off-by: Tom Rix <trix@redhat.com>
Link: https://lore.kernel.org/r/20201101155601.2294374-1-trix@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: hongrongxuan <hongrongxuan@huawei.com>
Like all genl families ethtool_genl_family needs to not
be a straight up constant, because it's modified/initialized
by genl_register_family(). After init, however, it's only
passed to genlmsg_put() & co. therefore we can mark it
as __ro_after_init.
Since genl_family structure contains function pointers
mark this as a fix.
Fixes: 2b4a8990b7 ("ethtool: introduce ethtool netlink interface")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: hongrongxuan <hongrongxuan@huawei.com>
Add entries for the 100base-FX full and half duplex supported modes.
$ ethtool eth0
Supported ports: [ FIBRE ]
Supported link modes: 100baseFX/Half 100baseFX/Full
Supported pause frame use: Symmetric Receive-only
Supports auto-negotiation: No
Supported FEC modes: Not reported
Advertised link modes: 100baseFX/Half 100baseFX/Full
Advertised pause frame use: No
Advertised auto-negotiation: No
Advertised FEC modes: Not reported
Speed: 100Mb/s
Duplex: Full
Auto-negotiation: off
Port: MII
PHYAD: 1
Transceiver: external
Supports Wake-on: gs
Wake-on: d
SecureOn password: 00:00:00:00:00:00
Current message level: 0x00000000 (0)
Link detected: yes
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: hongrongxuan <hongrongxuan@huawei.com>
Currently drivers have to report their pause frames statistics
via ethtool -S, and there is a wide variety of names used for
these statistics.
Add the two statistics defined in IEEE 802.3x to the standard
API. Create a new ethtool request header flag for including
statistics in the response to GET commands.
Always create the ETHTOOL_A_PAUSE_STATS nest in replies when
flag is set. Testing if driver declares the op is not a reliable
way of checking if any stats will actually be included and therefore
we don't want to give the impression that presence of
ETHTOOL_A_PAUSE_STATS indicates driver support.
Note that this patch does not include PFC counters, which may fit
better in dcbnl? But mostly I don't need them/have a setup to test
them so I haven't looked deeply into exposing them :)
v3:
- add a helper for "uninitializing" stats, rather than a cryptic
memset() (Andrew)
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: hongrongxuan <hongrongxuan@huawei.com>
Set IP protocol mask only when IP protocol field is set.
This will allow flow-type ether with vlan rule which don't have
protocol field to apply.
ethtool -N ens5f4 flow-type ether proto 0x8100 vlan 0x600\
m 0x1FFF action 3 loc 16
Signed-off-by: Vishal Kulkarni <vishal@chelsio.com>
Reviewed-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: hongrongxuan <hongrongxuan@huawei.com>
info cannot be NULL here since its being accessed earlier
in the function: nlmsg_parse(info->nlhdr...). Remove this
redundant NULL check.
Signed-off-by: Gaurav Singh <gaurav1086@gmail.com>
Reviewed-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: hongrongxuan <hongrongxuan@huawei.com>
If the genlmsg_put() call in ethnl_default_dumpit() fails, we bail out
without checking if we already have some messages in current skb like we do
with ethnl_default_dump_one() failure later. Therefore if existing messages
almost fill up the buffer so that there is not enough space even for
netlink and genetlink header, we lose all prepared messages and return and
error.
Rather than duplicating the skb->len check, move the genlmsg_put(),
genlmsg_cancel() and genlmsg_end() calls into ethnl_default_dump_one().
This is also more logical as all message composition will be in
ethnl_default_dump_one() and only iteration logic will be left in
ethnl_default_dumpit().
Fixes: 728480f124 ("ethtool: default handlers for GET requests")
Reported-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: hongrongxuan <hongrongxuan@huawei.com>
Define 100G, 200G and 400G link modes using 100Gbps per lane
LR, ER and FR are defined as a single link mode because they are
using same technology and by design are fully interoperable.
EEPROM content indicates if the module is LR, ER, or FR, and the
user space ethtool decoder is planned to support decoding these
modes in the EEPROM.
Signed-off-by: Meir Lichtinger <meirl@mellanox.com>
CC: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Aya Levin <ayal@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: hongrongxuan <hongrongxuan@huawei.com>
Currently, drivers can only tell whether the link is up/down using
LINKSTATE_GET, but no additional information is given.
Add attributes to LINKSTATE_GET command in order to allow drivers
to expose the user more information in addition to link state to ease
the debug process, for example, reason for link down state.
Extended state consists of two attributes - link_ext_state and
link_ext_substate. The idea is to avoid 'vendor specific' states in order
to prevent drivers to use specific link_ext_state that can be in the future
common link_ext_state.
The substates allows drivers to add more information to the common
link_ext_state. For example, vendor can expose 'Autoneg' as link_ext_state
and add 'No partner detected during force mode' as link_ext_substate.
If a driver cannot pinpoint the extended state with the substate
accuracy, it is free to expose only the extended state and omit the
substate attribute.
Signed-off-by: Amit Cohen <amitc@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: hongrongxuan <hongrongxuan@huawei.com>
Fix check in ethtool_rx_flow_rule_create
Fixes: eca4205f9e ("ethtool: add ethtool_rx_flow_spec to flow_rule structure translator")
Signed-off-by: Gaurav Singh <gaurav1086@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: hongrongxuan <hongrongxuan@huawei.com>
Use array_size() helper instead of the open-coded version in
copy_to_user(). These sorts of multiplication factors need to
be wrapped in array_size().
This issue was found with the help of Coccinelle and, audited and fixed
manually.
Addresses-KSPP-ID: https://github.com/KSPP/linux/issues/83
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: hongrongxuan <hongrongxuan@huawei.com>
This code generates a Smatch warning:
net/ethtool/linkinfo.c:143 ethnl_set_linkinfo()
warn: variable dereferenced before check 'info' (see line 119)
Fortunately, the "info" pointer is never NULL so the check can be
removed.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: hongrongxuan <hongrongxuan@huawei.com>
get_coalesce returns 0 or ERRNO, but the return value isn't checked.
The returned coalesce data may be invalid if an ERRNO is set,
therefore better check and propagate the return value.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: hongrongxuan <hongrongxuan@huawei.com>
When getting SQI or maximum SQI value fails in linkstate_prepare_data(), we
must not return without calling ethnl_ops_complete(dev) as that could
result in imbalance between ethtool_ops ->begin() and ->complete() calls.
Fixes: 8066021915 ("ethtool: provide UAPI for PHY Signal Quality Index (SQI)")
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: hongrongxuan <hongrongxuan@huawei.com>
As ethnl_request_ops::reply_size handlers do not include common header
size into calculated/estimated reply size, it needs to be added in
ethnl_default_doit() and ethnl_default_notify() before allocating the
message. On the other hand, strset_reply_size() should not add common
header size.
Fixes: 728480f124 ("ethtool: default handlers for GET requests")
Reported-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: hongrongxuan <hongrongxuan@huawei.com>
Don't call drivers if nothing changed. Netlink code already
contains this logic.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: hongrongxuan <hongrongxuan@huawei.com>
Having a channel config with no ability to RX or TX traffic is
clearly wrong. Check for this in the core so the drivers don't
have to.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: hongrongxuan <hongrongxuan@huawei.com>
This UAPI is needed for BroadR-Reach 100BASE-T1 devices. Due to lack of
auto-negotiation support, we needed to be able to configure the
MASTER-SLAVE role of the port manually or from an application in user
space.
The same UAPI can be used for 1000BASE-T or MultiGBASE-T devices to
force MASTER or SLAVE role. See IEEE 802.3-2018:
22.2.4.3.7 MASTER-SLAVE control register (Register 9)
22.2.4.3.8 MASTER-SLAVE status register (Register 10)
40.5.2 MASTER-SLAVE configuration resolution
45.2.1.185.1 MASTER-SLAVE config value (1.2100.14)
45.2.7.10 MultiGBASE-T AN control 1 register (Register 7.32)
The MASTER-SLAVE role affects the clock configuration:
-------------------------------------------------------------------------------
When the PHY is configured as MASTER, the PMA Transmit function shall
source TX_TCLK from a local clock source. When configured as SLAVE, the
PMA Transmit function shall source TX_TCLK from the clock recovered from
data stream provided by MASTER.
iMX6Q KSZ9031 XXX
------\ /-----------\ /------------\
| | | | |
MAC |<----RGMII----->| PHY Slave |<------>| PHY Master |
|<--- 125 MHz ---+-<------/ | | \ |
------/ \-----------/ \------------/
^
\-TX_TCLK
-------------------------------------------------------------------------------
Since some clock or link related issues are only reproducible in a
specific MASTER-SLAVE-role, MAC and PHY configuration, it is beneficial
to provide generic (not 100BASE-T1 specific) interface to the user space
for configuration flexibility and trouble shooting.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: hongrongxuan <hongrongxuan@huawei.com>
Conflicts:
drivers/net/phy/phy.c
Danielle Ratson