Due to the way Machine Check Exceptions work on X86 hyperthreads it's
required to boot up _all_ logical cores at least once in order to set the
CR4.MCE bit.
So instead of ignoring the sibling threads right away, let them boot up
once so they can configure themselves. After they came out of the initial
boot stage check whether its a "secondary" sibling and cancel the operation
which puts the CPU back into offline state.
Reported-by: Dave Hansen <dave.hansen@intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Tony Luck <tony.luck@intel.com>
Provide a command line and a sysfs knob to control SMT.
The command line options are:
'nosmt': Enumerate secondary threads, but do not online them
'nosmt=force': Ignore secondary threads completely during enumeration
via MP table and ACPI/MADT.
The sysfs control file has the following states (read/write):
'on': SMT is enabled. Secondary threads can be freely onlined
'off': SMT is disabled. Secondary threads, even if enumerated
cannot be onlined
'forceoff': SMT is permanentely disabled. Writes to the control
file are rejected.
'notsupported': SMT is not supported by the CPU
The command line option 'nosmt' sets the sysfs control to 'off'. This
can be changed to 'on' to reenable SMT during runtime.
The command line option 'nosmt=force' sets the sysfs control to
'forceoff'. This cannot be changed during runtime.
When SMT is 'on' and the control file is changed to 'off' then all online
secondary threads are offlined and attempts to online a secondary thread
later on are rejected.
When SMT is 'off' and the control file is changed to 'on' then secondary
threads can be onlined again. The 'off' -> 'on' transition does not
automatically online the secondary threads.
When the control file is set to 'forceoff', the behaviour is the same as
setting it to 'off', but the operation is irreversible and later writes to
the control file are rejected.
When the control status is 'notsupported' then writes to the control file
are rejected.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Acked-by: Ingo Molnar <mingo@kernel.org>
Split out the inner workings of do_cpu_down() to allow reuse of that
function for the upcoming SMT disabling mechanism.
No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Acked-by: Ingo Molnar <mingo@kernel.org>
The asymmetry caused a warning to trigger if the bootup was stopped in state
CPUHP_AP_ONLINE_IDLE. The warning no longer triggers as kthread_park() can
now be invoked on already or still parked threads. But there is still no
reason to have this be asymmetric.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Acked-by: Ingo Molnar <mingo@kernel.org>
The cpuhp_is_ap_state() function is no longer called outside of the
CONFIG_SMP #ifdef section, causing a harmless warning:
kernel/cpu.c:129:13: error: 'cpuhp_is_ap_state' defined but not used [-Werror=unused-function]
This moves the function into the #ifdef to get a clean build again.
Fixes: 17a2f1ced0 ("cpu/hotplug: Merge cpuhp_bp_states and cpuhp_ap_states")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Lai Jiangshan <jiangshanlai@gmail.com>
Cc: "Paul E. McKenney" <paulmck@linux.vnet.ibm.com>
Link: https://lkml.kernel.org/r/20180315153829.3819606-1-arnd@arndb.de
cpuhp_bp_states and cpuhp_ap_states have different set of steps without any
conflicting steps, so that they can be merged.
The original `[CPUHP_BRINGUP_CPU] = { },` is removed, because the new
cpuhp_hp_states has CPUHP_ONLINE index which is larger than
CPUHP_BRINGUP_CPU.
Signed-off-by: Lai Jiangshan <jiangshanlai@gmail.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: "Paul E. McKenney" <paulmck@linux.vnet.ibm.com>
Link: https://lkml.kernel.org/r/20171201135008.21633-1-jiangshanlai@gmail.com
Pull timer fixes from Thomas Gleixner:
"A pile of fixes for long standing issues with the timer wheel and the
NOHZ code:
- Prevent timer base confusion accross the nohz switch, which can
cause unlocked access and data corruption
- Reinitialize the stale base clock on cpu hotplug to prevent subtle
side effects including rollovers on 32bit
- Prevent an interrupt storm when the timer softirq is already
pending caused by tick_nohz_stop_sched_tick()
- Move the timer start tracepoint to a place where it actually makes
sense
- Add documentation to timerqueue functions as they caused confusion
several times now"
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
timerqueue: Document return values of timerqueue_add/del()
timers: Invoke timer_start_debug() where it makes sense
nohz: Prevent a timer interrupt storm in tick_nohz_stop_sched_tick()
timers: Reinitialize per cpu bases on hotplug
timers: Use deferrable base independent of base::nohz_active
The timer wheel bases are not (re)initialized on CPU hotplug. That leaves
them with a potentially stale clk and next_expiry valuem, which can cause
trouble then the CPU is plugged.
Add a prepare callback which forwards the clock, sets next_expiry to far in
the future and reset the control flags to a known state.
Set base->must_forward_clk so the first timer which is queued will try to
forward the clock to current jiffies.
Fixes: 500462a9de ("timers: Switch to a non-cascading wheel")
Reported-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Sebastian Siewior <bigeasy@linutronix.de>
Cc: Anna-Maria Gleixner <anna-maria@linutronix.de>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/alpine.DEB.2.20.1712272152200.2431@nanos
Pull CPU hotplug fix from Ingo Molnar:
"A single fix moving the smp-call queue flush step to the intended
point in the state machine"
* 'smp-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
smp/hotplug: Move step CPUHP_AP_SMPCFD_DYING to the correct place
CPUHP_AP_SCHED_MIGRATE_DYING doesn't exist, it looks like this was
supposed to refer to CPUHP_AP_SCHED_STARTING's teardown callback,
i.e. sched_cpu_dying().
Signed-off-by: Brendan Jackman <brendan.jackman@arm.com>
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: Dietmar Eggemann <dietmar.eggemann@arm.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Quentin Perret <quentin.perret@arm.com>
Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/20171206105911.28093-1-brendan.jackman@arm.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Commit 31487f8328 ("smp/cfd: Convert core to hotplug state machine")
accidently put this step on the wrong place. The step should be at the
cpuhp_ap_states[] rather than the cpuhp_bp_states[].
grep smpcfd /sys/devices/system/cpu/hotplug/states
40: smpcfd:prepare
129: smpcfd:dying
"smpcfd:dying" was missing before.
So was the invocation of the function smpcfd_dying_cpu().
Fixes: 31487f8328 ("smp/cfd: Convert core to hotplug state machine")
Signed-off-by: Lai Jiangshan <jiangshanlai@gmail.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Richard Weinberger <richard@nod.at>
Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: stable@vger.kernel.org
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Link: https://lkml.kernel.org/r/20171128131954.81229-1-jiangshanlai@gmail.com
The recent rework of the cpu hotplug internals changed the usage of the per
cpu state->node field, but missed to clean it up after usage.
So subsequent hotplug operations use the stale pointer from a previous
operation and hand it into the callback functions. The callbacks then
dereference a pointer which either belongs to a different facility or
points to freed and potentially reused memory. In either case data
corruption and crashes are the obvious consequence.
Reset the node and the last pointers in the per cpu state to NULL after the
operation which set them has completed.
Fixes: 96abb96854 ("smp/hotplug: Allow external multi-instance rollback")
Reported-by: Tvrtko Ursulin <tursulin@ursulin.net>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: "Paul E. McKenney" <paulmck@linux.vnet.ibm.com>
Link: https://lkml.kernel.org/r/alpine.DEB.2.20.1710211606130.3213@nanos
Pull watchddog clean-up and fixes from Thomas Gleixner:
"The watchdog (hard/softlockup detector) code is pretty much broken in
its current state. The patch series addresses this by removing all
duct tape and refactoring it into a workable state.
The reasons why I ask for inclusion that late in the cycle are:
1) The code causes lockdep splats vs. hotplug locking which get
reported over and over. Unfortunately there is no easy fix.
2) The risk of breakage is minimal because it's already broken
3) As 4.14 is a long term stable kernel, I prefer to have working
watchdog code in that and the lockdep issues resolved. I wouldn't
ask you to pull if 4.14 wouldn't be a LTS kernel or if the
solution would be easy to backport.
4) The series was around before the merge window opened, but then got
delayed due to the UP failure caused by the for_each_cpu()
surprise which we discussed recently.
Changes vs. V1:
- Addressed your review points
- Addressed the warning in the powerpc code which was discovered late
- Changed two function names which made sense up to a certain point
in the series. Now they match what they do in the end.
- Fixed a 'unused variable' warning, which got not detected by the
intel robot. I triggered it when trying all possible related config
combinations manually. Randconfig testing seems not random enough.
The changes have been tested by and reviewed by Don Zickus and tested
and acked by Micheal Ellerman for powerpc"
* 'core-watchdog-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (36 commits)
watchdog/core: Put softlockup_threads_initialized under ifdef guard
watchdog/core: Rename some softlockup_* functions
powerpc/watchdog: Make use of watchdog_nmi_probe()
watchdog/core, powerpc: Lock cpus across reconfiguration
watchdog/core, powerpc: Replace watchdog_nmi_reconfigure()
watchdog/hardlockup/perf: Fix spelling mistake: "permanetely" -> "permanently"
watchdog/hardlockup/perf: Cure UP damage
watchdog/hardlockup: Clean up hotplug locking mess
watchdog/hardlockup/perf: Simplify deferred event destroy
watchdog/hardlockup/perf: Use new perf CPU enable mechanism
watchdog/hardlockup/perf: Implement CPU enable replacement
watchdog/hardlockup/perf: Implement init time detection of perf
watchdog/hardlockup/perf: Implement init time perf validation
watchdog/core: Get rid of the racy update loop
watchdog/core, powerpc: Make watchdog_nmi_reconfigure() two stage
watchdog/sysctl: Clean up sysctl variable name space
watchdog/sysctl: Get rid of the #ifdeffery
watchdog/core: Clean up header mess
watchdog/core: Further simplify sysctl handling
watchdog/core: Get rid of the thread teardown/setup dance
...
Add a sysfs file to one-time fail a specific state. This can be used
to test the state rollback code paths.
Something like this (hotplug-up.sh):
#!/bin/bash
echo 0 > /debug/sched_debug
echo 1 > /debug/tracing/events/cpuhp/enable
ALL_STATES=`cat /sys/devices/system/cpu/hotplug/states | cut -d':' -f1`
STATES=${1:-$ALL_STATES}
for state in $STATES
do
echo 0 > /sys/devices/system/cpu/cpu1/online
echo 0 > /debug/tracing/trace
echo Fail state: $state
echo $state > /sys/devices/system/cpu/cpu1/hotplug/fail
cat /sys/devices/system/cpu/cpu1/hotplug/fail
echo 1 > /sys/devices/system/cpu/cpu1/online
cat /debug/tracing/trace > hotfail-${state}.trace
sleep 1
done
Can be used to test for all possible rollback (barring multi-instance)
scenarios on CPU-up, CPU-down is a trivial modification of the above.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: bigeasy@linutronix.de
Cc: efault@gmx.de
Cc: rostedt@goodmis.org
Cc: max.byungchul.park@gmail.com
Link: https://lkml.kernel.org/r/20170920170546.972581715@infradead.org
With lockdep-crossrelease we get deadlock reports that span cpu-up and
cpu-down chains. Such deadlocks cannot possibly happen because cpu-up
and cpu-down are globally serialized.
takedown_cpu()
irq_lock_sparse()
wait_for_completion(&st->done)
cpuhp_thread_fun
cpuhp_up_callback
cpuhp_invoke_callback
irq_affinity_online_cpu
irq_local_spare()
irq_unlock_sparse()
complete(&st->done)
Now that we have consistent AP state, we can trivially separate the
AP completion between up and down using st->bringup.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: max.byungchul.park@gmail.com
Cc: bigeasy@linutronix.de
Cc: efault@gmx.de
Cc: rostedt@goodmis.org
Link: https://lkml.kernel.org/r/20170920170546.872472799@infradead.org
With lockdep-crossrelease we get deadlock reports that span cpu-up and
cpu-down chains. Such deadlocks cannot possibly happen because cpu-up
and cpu-down are globally serialized.
CPU0 CPU1 CPU2
cpuhp_up_callbacks: takedown_cpu: cpuhp_thread_fun:
cpuhp_state
irq_lock_sparse()
irq_lock_sparse()
wait_for_completion()
cpuhp_state
complete()
Now that we have consistent AP state, we can trivially separate the
AP-work class between up and down using st->bringup.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: max.byungchul.park@gmail.com
Cc: bigeasy@linutronix.de
Cc: efault@gmx.de
Cc: rostedt@goodmis.org
Link: https://lkml.kernel.org/r/20170920170546.922524234@infradead.org
While the generic callback functions have an 'int' return and thus
appear to be allowed to return error, this is not true for all states.
Specifically, what used to be STARTING/DYING are ran with IRQs
disabled from critical parts of CPU bringup/teardown and are not
allowed to fail. Add WARNs to enforce this rule.
But since some callbacks are indeed allowed to fail, we have the
situation where a state-machine rollback encounters a failure, in this
case we're stuck, we can't go forward and we can't go back. Also add a
WARN for that case.
AFAICT this is a fundamental 'problem' with no real obvious solution.
We want the 'prepare' callbacks to allow failure on either up or down.
Typically on prepare-up this would be things like -ENOMEM from
resource allocations, and the typical usage in prepare-down would be
something like -EBUSY to avoid CPUs being taken away.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: bigeasy@linutronix.de
Cc: efault@gmx.de
Cc: rostedt@goodmis.org
Cc: max.byungchul.park@gmail.com
Link: https://lkml.kernel.org/r/20170920170546.819539119@infradead.org
There is currently no explicit state change on rollback. That is,
st->bringup, st->rollback and st->target are not consistent when doing
the rollback.
Rework the AP state handling to be more coherent. This does mean we
have to do a second AP kick-and-wait for rollback, but since rollback
is the slow path of a slowpath, this really should not matter.
Take this opportunity to simplify the AP thread function to only run a
single callback per invocation. This unifies the three single/up/down
modes is supports. The looping it used to do for up/down are achieved
by retaining should_run and relying on the main smpboot_thread_fn()
loop.
(I have most of a patch that does the same for the BP state handling,
but that's not critical and gets a little complicated because
CPUHP_BRINGUP_CPU does the AP handoff from a callback, which gets
recursive @st usage, I still have de-fugly that.)
[ tglx: Move cpuhp_down_callbacks() et al. into the HOTPLUG_CPU section to
avoid gcc complaining about unused functions. Make the HOTPLUG_CPU
one piece instead of having two consecutive ifdef sections of the
same type. ]
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: bigeasy@linutronix.de
Cc: efault@gmx.de
Cc: rostedt@goodmis.org
Cc: max.byungchul.park@gmail.com
Link: https://lkml.kernel.org/r/20170920170546.769658088@infradead.org
Currently the rollback of multi-instance states is handled inside
cpuhp_invoke_callback(). The problem is that when we want to allow an
explicit state change for rollback, we need to return from the
function without doing the rollback.
Change cpuhp_invoke_callback() to optionally return the multi-instance
state, such that rollback can be done from a subsequent call.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: bigeasy@linutronix.de
Cc: efault@gmx.de
Cc: rostedt@goodmis.org
Cc: max.byungchul.park@gmail.com
Link: https://lkml.kernel.org/r/20170920170546.720361181@infradead.org
The following deadlock is possible in the watchdog hotplug code:
cpus_write_lock()
...
takedown_cpu()
smpboot_park_threads()
smpboot_park_thread()
kthread_park()
->park() := watchdog_disable()
watchdog_nmi_disable()
perf_event_release_kernel();
put_event()
_free_event()
->destroy() := hw_perf_event_destroy()
x86_release_hardware()
release_ds_buffers()
get_online_cpus()
when a per cpu watchdog perf event is destroyed which drops the last
reference to the PMU hardware. The cleanup code there invokes
get_online_cpus() which instantly deadlocks because the hotplug percpu
rwsem is write locked.
To solve this add a deferring mechanism:
cpus_write_lock()
kthread_park()
watchdog_nmi_disable(deferred)
perf_event_disable(event);
move_event_to_deferred(event);
....
cpus_write_unlock()
cleaup_deferred_events()
perf_event_release_kernel()
This is still properly serialized against concurrent hotplug via the
cpu_add_remove_lock, which is held by the task which initiated the hotplug
event.
This is also used to handle event destruction when the watchdog threads are
parked via other mechanisms than CPU hotplug.
Analyzed-by: Peter Zijlstra <peterz@infradead.org>
Reported-by: Borislav Petkov <bp@alien8.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Don Zickus <dzickus@redhat.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Chris Metcalf <cmetcalf@mellanox.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Nicholas Piggin <npiggin@gmail.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Sebastian Siewior <bigeasy@linutronix.de>
Cc: Ulrich Obergfell <uobergfe@redhat.com>
Link: http://lkml.kernel.org/r/20170912194146.884469246@linutronix.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Pull CPU hotplug fix from Thomas Gleixner:
"A single fix to handle the removal of the first dynamic CPU hotplug
state correctly"
* 'smp-hotplug-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
smp/hotplug: Handle removal correctly in cpuhp_store_callbacks()
RCU callbacks must be migrated away from an outgoing CPU, and this is
done near the end of the CPU-hotplug operation, after the outgoing CPU is
long gone. Unfortunately, this means that other CPU-hotplug callbacks
can execute while the outgoing CPU's callbacks are still immobilized
on the long-gone CPU's callback lists. If any of these CPU-hotplug
callbacks must wait, either directly or indirectly, for the invocation
of any of the immobilized RCU callbacks, the system will hang.
This commit avoids such hangs by migrating the callbacks away from the
outgoing CPU immediately upon its departure, shortly after the return
from __cpu_die() in takedown_cpu(). Thus, RCU is able to advance these
callbacks and invoke them, which allows all the after-the-fact CPU-hotplug
callbacks to wait on these RCU callbacks without risk of a hang.
While in the neighborhood, this commit also moves rcu_send_cbs_to_orphanage()
and rcu_adopt_orphan_cbs() under a pre-existing #ifdef to avoid including
dead code on the one hand and to avoid define-without-use warnings on the
other hand.
Reported-by: Jeffrey Hugo <jhugo@codeaurora.org>
Link: http://lkml.kernel.org/r/db9c91f6-1b17-6136-84f0-03c3c2581ab4@codeaurora.org
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Anna-Maria Gleixner <anna-maria@linutronix.de>
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: Richard Weinberger <richard@nod.at>
If cpuhp_store_callbacks() is called for CPUHP_AP_ONLINE_DYN or
CPUHP_BP_PREPARE_DYN, which are the indicators for dynamically allocated
states, then cpuhp_store_callbacks() allocates a new dynamic state. The
first allocation in each range returns CPUHP_AP_ONLINE_DYN or
CPUHP_BP_PREPARE_DYN.
If cpuhp_remove_state() is invoked for one of these states, then there is
no protection against the allocation mechanism. So the removal, which
should clear the callbacks and the name, gets a new state assigned and
clears that one.
As a consequence the state which should be cleared stays initialized. A
consecutive CPU hotplug operation dereferences the state callbacks and
accesses either freed or reused memory, resulting in crashes.
Add a protection against this by checking the name argument for NULL. If
it's NULL it's a removal. If not, it's an allocation.
[ tglx: Added a comment and massaged changelog ]
Fixes: 5b7aa87e04 ("cpu/hotplug: Implement setup/removal interface")
Signed-off-by: Ethan Barnes <ethan.barnes@sandisk.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@kernel.or>
Cc: "Srivatsa S. Bhat" <srivatsa@mit.edu>
Cc: Sebastian Siewior <bigeasy@linutronix.d>
Cc: Paul McKenney <paulmck@linux.vnet.ibm.com>
Cc: stable@vger.kernel.org
Link: http://lkml.kernel.org/r/DM2PR04MB398242FC7776D603D9F99C894A60@DM2PR04MB398.namprd04.prod.outlook.com
The move of the unpark functions to the control thread moved the BUG_ON()
there as well. While it made some sense in the idle thread of the upcoming
CPU, it's bogus to crash the control thread on the already online CPU,
especially as the function has a return value and the callsite is prepared
to handle an error return.
Replace it with a WARN_ON_ONCE() and return a proper error code.
Fixes: 9cd4f1a4e7 ("smp/hotplug: Move unparking of percpu threads to the control CPU")
Rightfully-ranted-at-by: Linux Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Vikram reported the following backtrace:
BUG: scheduling while atomic: swapper/7/0/0x00000002
CPU: 7 PID: 0 Comm: swapper/7 Not tainted 4.9.32-perf+ #680
schedule
schedule_hrtimeout_range_clock
schedule_hrtimeout
wait_task_inactive
__kthread_bind_mask
__kthread_bind
__kthread_unpark
kthread_unpark
cpuhp_online_idle
cpu_startup_entry
secondary_start_kernel
He analyzed correctly that a parked cpu hotplug thread of an offlined CPU
was still on the runqueue when the CPU came back online and tried to unpark
it. This causes the thread which invoked kthread_unpark() to call
wait_task_inactive() and subsequently schedule() with preemption disabled.
His proposed workaround was to "make sure" that a parked thread has
scheduled out when the CPU goes offline, so the situation cannot happen.
But that's still wrong because the root cause is not the fact that the
percpu thread is still on the runqueue and neither that preemption is
disabled, which could be simply solved by enabling preemption before
calling kthread_unpark().
The real issue is that the calling thread is the idle task of the upcoming
CPU, which is not supposed to call anything which might sleep. The moron,
who wrote that code, missed completely that kthread_unpark() might end up
in schedule().
The solution is simpler than expected. The thread which controls the
hotplug operation is waiting for the CPU to call complete() on the hotplug
state completion. So the idle task of the upcoming CPU can set its state to
CPUHP_AP_ONLINE_IDLE and invoke complete(). This in turn wakes the control
task on a different CPU, which then can safely do the unpark and kick the
now unparked hotplug thread of the upcoming CPU to complete the bringup to
the final target state.
Control CPU AP
bringup_cpu();
__cpu_up() ------------>
bringup_ap();
bringup_wait_for_ap()
wait_for_completion();
cpuhp_online_idle();
<------------ complete();
unpark(AP->stopper);
unpark(AP->hotplugthread);
while(1)
do_idle();
kick(AP->hotplugthread);
wait_for_completion(); hotplug_thread()
run_online_callbacks();
complete();
Fixes: 8df3e07e7f ("cpu/hotplug: Let upcoming cpu bring itself fully up")
Reported-by: Vikram Mulukutla <markivx@codeaurora.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Peter Zijlstra <peterz@infradead.org>
Cc: Sebastian Sewior <bigeasy@linutronix.de>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Tejun Heo <tj@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Link: http://lkml.kernel.org/r/alpine.DEB.2.20.1707042218020.2131@nanos
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Pull SMP hotplug updates from Thomas Gleixner:
"This update is primarily a cleanup of the CPU hotplug locking code.
The hotplug locking mechanism is an open coded RWSEM, which allows
recursive locking. The main problem with that is the recursive nature
as it evades the full lockdep coverage and hides potential deadlocks.
The rework replaces the open coded RWSEM with a percpu RWSEM and
establishes full lockdep coverage that way.
The bulk of the changes fix up recursive locking issues and address
the now fully reported potential deadlocks all over the place. Some of
these deadlocks have been observed in the RT tree, but on mainline the
probability was low enough to hide them away."
* 'smp-hotplug-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (37 commits)
cpu/hotplug: Constify attribute_group structures
powerpc: Only obtain cpu_hotplug_lock if called by rtasd
ARM/hw_breakpoint: Fix possible recursive locking for arch_hw_breakpoint_init
cpu/hotplug: Remove unused check_for_tasks() function
perf/core: Don't release cred_guard_mutex if not taken
cpuhotplug: Link lock stacks for hotplug callbacks
acpi/processor: Prevent cpu hotplug deadlock
sched: Provide is_percpu_thread() helper
cpu/hotplug: Convert hotplug locking to percpu rwsem
s390: Prevent hotplug rwsem recursion
arm: Prevent hotplug rwsem recursion
arm64: Prevent cpu hotplug rwsem recursion
kprobes: Cure hotplug lock ordering issues
jump_label: Reorder hotplug lock and jump_label_lock
perf/tracing/cpuhotplug: Fix locking order
ACPI/processor: Use cpu_hotplug_disable() instead of get_online_cpus()
PCI: Replace the racy recursion prevention
PCI: Use cpu_hotplug_disable() instead of get_online_cpus()
perf/x86/intel: Drop get_online_cpus() in intel_snb_check_microcode()
x86/perf: Drop EXPORT of perf_check_microcode
...
attribute_groups are not supposed to change at runtime. All functions
working with attribute_groups provided by <linux/sysfs.h> work with const
attribute_group.
So mark the non-const structs as const:
File size before:
text data bss dec hex filename
12582 15361 20 27963 6d3b kernel/cpu.o
File size After adding 'const':
text data bss dec hex filename
12710 15265 20 27995 6d5b kernel/cpu.o
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: anna-maria@linutronix.de
Cc: bigeasy@linutronix.de
Cc: boris.ostrovsky@oracle.com
Cc: rcochran@linutronix.de
Link: http://lkml.kernel.org/r/f9079e94e12b36d245e7adbf67d312bc5d0250c6.1498737970.git.arvind.yadav.cs@gmail.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
If a CPU goes offline, interrupts affine to the CPU are moved away. If the
outgoing CPU is the last CPU in the affinity mask the migration code breaks
the affinity and sets it it all online cpus.
This is a problem for affinity managed interrupts as CPU hotplug is often
used for power management purposes. If the affinity is broken, the
interrupt is not longer affine to the CPUs to which it was allocated.
The affinity spreading allows to lay out multi queue devices in a way that
they are assigned to a single CPU or a group of CPUs. If the last CPU goes
offline, then the queue is not longer used, so the interrupt can be
shutdown gracefully and parked until one of the assigned CPUs comes online
again.
Add a graceful shutdown mechanism into the irq affinity breaking code path,
mark the irq as MANAGED_SHUTDOWN and leave the affinity mask unmodified.
In the online path, scan the active interrupts for managed interrupts and
if the interrupt is functional and the newly online CPU is part of the
affinity mask, restart the interrupt if it is marked MANAGED_SHUTDOWN or if
the interrupts is started up, try to add the CPU back to the effective
affinity mask.
Originally-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Keith Busch <keith.busch@intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/20170619235447.273417334@linutronix.de
clang -Wunused-function found one remaining function that was
apparently meant to be removed in a recent code cleanup:
kernel/cpu.c:565:20: warning: unused function 'check_for_tasks' [-Wunused-function]
Sebastian explained: The function became unused unintentionally, but there
is already a failure check, when a task cannot be removed from the outgoing
cpu in the scheduler code, so bringing it back is not really giving any
extra value.
Fixes: 530e9b76ae ("cpu/hotplug: Remove obsolete cpu hotplug register/unregister functions")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: Anna-Maria Gleixner <anna-maria@linutronix.de>
Link: http://lkml.kernel.org/r/20170608085544.2257132-1-arnd@arndb.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
If a custom CPU target is specified and that one is not available _or_
can't be interrupted then the code returns to userland without dropping a
lock as notices by lockdep:
|echo 133 > /sys/devices/system/cpu/cpu7/hotplug/target
| ================================================
| [ BUG: lock held when returning to user space! ]
| ------------------------------------------------
| bash/503 is leaving the kernel with locks still held!
| 1 lock held by bash/503:
| #0: (device_hotplug_lock){+.+...}, at: [<ffffffff815b5650>] lock_device_hotplug_sysfs+0x10/0x40
So release the lock then.
Fixes: 757c989b99 ("cpu/hotplug: Make target state writeable")
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
Link: http://lkml.kernel.org/r/20170602142714.3ogo25f2wbq6fjpj@linutronix.de
The CPU hotplug callbacks are not covered by lockdep versus the cpu hotplug
rwsem.
CPU0 CPU1
cpuhp_setup_state(STATE, startup, teardown);
cpus_read_lock();
invoke_callback_on_ap();
kick_hotplug_thread(ap);
wait_for_completion(); hotplug_thread_fn()
lock(m);
do_stuff();
unlock(m);
Lockdep does not know about this dependency and will not trigger on the
following code sequence:
lock(m);
cpus_read_lock();
Add a lockdep map and connect the initiators lock chain with the hotplug
thread lock chain, so potential deadlocks can be detected.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Acked-by: Ingo Molnar <mingo@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Sebastian Siewior <bigeasy@linutronix.de>
Cc: Steven Rostedt <rostedt@goodmis.org>
Link: http://lkml.kernel.org/r/20170524081549.709375845@linutronix.de
There are no more (known) nested calls to get_online_cpus() and all
observed lock ordering problems have been addressed.
Replace the magic nested 'rwsem' hackery with a percpu-rwsem.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Acked-by: Ingo Molnar <mingo@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Sebastian Siewior <bigeasy@linutronix.de>
Cc: Steven Rostedt <rostedt@goodmis.org>
Link: http://lkml.kernel.org/r/20170524081549.447014063@linutronix.de
takedown_cpu() is a cpu hotplug function invoking stop_machine(). The cpu
hotplug machinery holds the hotplug lock for write.
stop_machine() invokes get_online_cpus() as well. This is correct, but
prevents the conversion of the hotplug locking to a percpu rwsem.
Use stop_machine_cpuslocked() to avoid the nested call.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Acked-by: Ingo Molnar <mingo@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Link: http://lkml.kernel.org/r/20170524081548.423292433@linutronix.de
Add cpuslocked() variants for the multi instance registration so this can
be called from a cpus_read_lock() protected region.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Acked-by: Ingo Molnar <mingo@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Sebastian Siewior <bigeasy@linutronix.de>
Cc: Steven Rostedt <rostedt@goodmis.org>
Link: http://lkml.kernel.org/r/20170524081547.321782217@linutronix.de
Some call sites of cpuhp_setup/remove_state[_nocalls]() are within a
cpus_read locked region.
cpuhp_setup/remove_state[_nocalls]() call cpus_read_lock() as well, which
is possible in the current implementation but prevents converting the
hotplug locking to a percpu rwsem.
Provide locked versions of the interfaces to avoid nested calls to
cpus_read_lock().
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Acked-by: Ingo Molnar <mingo@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Link: http://lkml.kernel.org/r/20170524081547.239600868@linutronix.de
The counting 'rwsem' hackery of get|put_online_cpus() is going to be
replaced by percpu rwsem.
Rename the functions to make it clear that it's locking and not some
refcount style interface. These new functions will be used for the
preparatory patches which make the code ready for the percpu rwsem
conversion.
Rename all instances in the cpu hotplug code while at it.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Acked-by: Ingo Molnar <mingo@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Sebastian Siewior <bigeasy@linutronix.de>
Cc: Steven Rostedt <rostedt@goodmis.org>
Link: http://lkml.kernel.org/r/20170524081547.080397752@linutronix.de
Since commit 383776fa75 ("locking/lockdep: Handle statically initialized
PER_CPU locks properly") we try to collapse per-cpu locks into a single
class by giving them all the same key. For this key we choose the canonical
address of the per-cpu object, which would be the offset into the per-cpu
area.
This has two problems:
- there is a case where we run !0 lock->key through static_obj() and
expect this to pass; it doesn't for canonical pointers.
- 0 is a valid canonical address.
Cure both issues by redefining the canonical address as the address of the
per-cpu variable on the boot CPU.
Since I didn't want to rely on CPU0 being the boot-cpu, or even existing at
all, track the boot CPU in a variable.
Fixes: 383776fa75 ("locking/lockdep: Handle statically initialized PER_CPU locks properly")
Reported-by: kernel test robot <fengguang.wu@intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Tested-by: Borislav Petkov <bp@suse.de>
Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: linux-mm@kvack.org
Cc: wfg@linux.intel.com
Cc: kernel test robot <fengguang.wu@intel.com>
Cc: LKP <lkp@01.org>
Link: http://lkml.kernel.org/r/20170320114108.kbvcsuepem45j5cr@hirez.programming.kicks-ass.net
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The setup/remove_state/instance() functions in the hotplug core code are
serialized against concurrent CPU hotplug, but unfortunately not serialized
against themself.
As a consequence a concurrent invocation of these function results in
corruption of the callback machinery because two instances try to invoke
callbacks on remote cpus at the same time. This results in missing callback
invocations and initiator threads waiting forever on the completion.
The obvious solution to replace get_cpu_online() with cpu_hotplug_begin()
is not possible because at least one callsite calls into these functions
from a get_online_cpu() locked region.
Extend the protection scope of the cpuhp_state_mutex from solely protecting
the state arrays to cover the callback invocation machinery as well.
Fixes: 5b7aa87e04 ("cpu/hotplug: Implement setup/removal interface")
Reported-and-tested-by: Bart Van Assche <Bart.VanAssche@sandisk.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: hpa@zytor.com
Cc: mingo@kernel.org
Cc: akpm@linux-foundation.org
Cc: torvalds@linux-foundation.org
Link: http://lkml.kernel.org/r/20170314150645.g4tdyoszlcbajmna@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
We are going to split <linux/sched/task.h> out of <linux/sched.h>, which
will have to be picked up from other headers and a couple of .c files.
Create a trivial placeholder <linux/sched/task.h> file that just
maps to <linux/sched.h> to make this patch obviously correct and
bisectable.
Include the new header in the files that are going to need it.
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
We are going to split <linux/sched/hotplug.h> out of <linux/sched.h>, which
will have to be picked up from other headers and a couple of .c files.
Create a trivial placeholder <linux/sched/hotplug.h> file that just
maps to <linux/sched.h> to make this patch obviously correct and
bisectable.
Include the new header in the files that are going to need it.
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
We are going to split <linux/sched/signal.h> out of <linux/sched.h>, which
will have to be picked up from other headers and a couple of .c files.
Create a trivial placeholder <linux/sched/signal.h> file that just
maps to <linux/sched.h> to make this patch obviously correct and
bisectable.
Include the new header in the files that are going to need it.
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
After the recent removal of the hotplug notifiers the variable 'hasdied' in
_cpu_down() is set but no longer read, leading to the following GCC warning
when building with 'make W=1':
kernel/cpu.c:767:7: warning: variable ‘hasdied’ set but not used [-Wunused-but-set-variable]
Fix it by removing the variable.
Fixes: 530e9b76ae ("cpu/hotplug: Remove obsolete cpu hotplug register/unregister functions")
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: rt@linutronix.de
Link: http://lkml.kernel.org/r/20170117143501.20893-1-tklauser@distanz.ch
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Mathieu reported that the LTTNG modules are broken as of 4.10-rc1 due to
the removal of the cpu hotplug notifiers.
Usually I don't care much about out of tree modules, but LTTNG is widely
used in distros. There are two ways to solve that:
1) Reserve a hotplug state for LTTNG
2) Add a dynamic range for the prepare states.
While #1 is the simplest solution, #2 is the proper one as we can convert
in tree users, which do not care about ordering, to the dynamic range as
well.
Add a dynamic range which allows LTTNG to request states in the prepare
stage.
Reported-and-tested-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Sebastian Sewior <bigeasy@linutronix.de>
Cc: Steven Rostedt <rostedt@goodmis.org>
Link: http://lkml.kernel.org/r/alpine.DEB.2.20.1701101353010.3401@nanos
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The attempt to prevent overwriting an active state resulted in a
disaster which effectively disables all dynamically allocated hotplug
states.
Cleanup the mess.
Fixes: dc280d9362 ("cpu/hotplug: Prevent overwriting of callbacks")
Reported-by: Markus Trippelsdorf <markus@trippelsdorf.de>
Reported-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
hotcpu_notifier(), cpu_notifier(), __hotcpu_notifier(), __cpu_notifier(),
register_hotcpu_notifier(), register_cpu_notifier(),
__register_hotcpu_notifier(), __register_cpu_notifier(),
unregister_hotcpu_notifier(), unregister_cpu_notifier(),
__unregister_hotcpu_notifier(), __unregister_cpu_notifier()
are unused now. Remove them and all related code.
Remove also the now pointless cpu notifier error injection mechanism. The
states can be executed step by step and error rollback is the same as cpu
down, so any state transition can be tested w/o requiring the notifier
error injection.
Some CPU hotplug states are kept as they are (ab)used for hotplug state
tracking.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: rt@linutronix.de
Link: http://lkml.kernel.org/r/20161221192112.005642358@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Developers manage to overwrite states blindly without thought. That's fatal
and hard to debug. Add sanity checks to make it fail.
This requries to restructure the code so that the dynamic state allocation
happens in the same lock protected section as the actual store. Otherwise
the previous assignment of 'Reserved' to the name field would trigger the
overwrite check.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Sebastian Siewior <bigeasy@linutronix.de>
Link: http://lkml.kernel.org/r/20161221192111.675234535@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Yu Zhao has noticed that __unregister_cpu_notifier only unregisters its
notifiers when HOTPLUG_CPU=y while the registration might succeed even
when HOTPLUG_CPU=n if MODULE is enabled. This means that e.g. zswap
might keep a stale notifier on the list on the manual clean up during
the pool tear down and thus corrupt the list. Resulting in the following
[ 144.964346] BUG: unable to handle kernel paging request at ffff880658a2be78
[ 144.971337] IP: [<ffffffffa290b00b>] raw_notifier_chain_register+0x1b/0x40
<snipped>
[ 145.122628] Call Trace:
[ 145.125086] [<ffffffffa28e5cf8>] __register_cpu_notifier+0x18/0x20
[ 145.131350] [<ffffffffa2a5dd73>] zswap_pool_create+0x273/0x400
[ 145.137268] [<ffffffffa2a5e0fc>] __zswap_param_set+0x1fc/0x300
[ 145.143188] [<ffffffffa2944c1d>] ? trace_hardirqs_on+0xd/0x10
[ 145.149018] [<ffffffffa2908798>] ? kernel_param_lock+0x28/0x30
[ 145.154940] [<ffffffffa2a3e8cf>] ? __might_fault+0x4f/0xa0
[ 145.160511] [<ffffffffa2a5e237>] zswap_compressor_param_set+0x17/0x20
[ 145.167035] [<ffffffffa2908d3c>] param_attr_store+0x5c/0xb0
[ 145.172694] [<ffffffffa290848d>] module_attr_store+0x1d/0x30
[ 145.178443] [<ffffffffa2b2b41f>] sysfs_kf_write+0x4f/0x70
[ 145.183925] [<ffffffffa2b2a5b9>] kernfs_fop_write+0x149/0x180
[ 145.189761] [<ffffffffa2a99248>] __vfs_write+0x18/0x40
[ 145.194982] [<ffffffffa2a9a412>] vfs_write+0xb2/0x1a0
[ 145.200122] [<ffffffffa2a9a732>] SyS_write+0x52/0xa0
[ 145.205177] [<ffffffffa2ff4d97>] entry_SYSCALL_64_fastpath+0x12/0x17
This can be even triggered manually by changing
/sys/module/zswap/parameters/compressor multiple times.
Fix this issue by making unregister APIs symmetric to the register so
there are no surprises.
Fixes: 47e627bc8c ("[PATCH] hotplug: Allow modules to use the cpu hotplug notifiers even if !CONFIG_HOTPLUG_CPU")
Reported-and-tested-by: Yu Zhao <yuzhao@google.com>
Signed-off-by: Michal Hocko <mhocko@suse.com>
Cc: linux-mm@kvack.org
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Dan Streetman <ddstreet@ieee.org>
Link: http://lkml.kernel.org/r/20161207135438.4310-1-mhocko@kernel.org
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Use distinctive name for cpu_hotplug.dep_map to avoid the actual
cpu_hotplug.lock appearing as cpu_hotplug.lock#2 in lockdep splats.
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Gautham R. Shenoy <ego@linux.vnet.ibm.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Gautham R . Shenoy <ego@linux.vnet.ibm.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: intel-gfx@lists.freedesktop.org
Cc: trivial@kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Pull CPU hotplug updates from Thomas Gleixner:
"Yet another batch of cpu hotplug core updates and conversions:
- Provide core infrastructure for multi instance drivers so the
drivers do not have to keep custom lists.
- Convert custom lists to the new infrastructure. The block-mq custom
list conversion comes through the block tree and makes the diffstat
tip over to more lines removed than added.
- Handle unbalanced hotplug enable/disable calls more gracefully.
- Remove the obsolete CPU_STARTING/DYING notifier support.
- Convert another batch of notifier users.
The relayfs changes which conflicted with the conversion have been
shipped to me by Andrew.
The remaining lot is targeted for 4.10 so that we finally can remove
the rest of the notifiers"
* 'smp-hotplug-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (46 commits)
cpufreq: Fix up conversion to hotplug state machine
blk/mq: Reserve hotplug states for block multiqueue
x86/apic/uv: Convert to hotplug state machine
s390/mm/pfault: Convert to hotplug state machine
mips/loongson/smp: Convert to hotplug state machine
mips/octeon/smp: Convert to hotplug state machine
fault-injection/cpu: Convert to hotplug state machine
padata: Convert to hotplug state machine
cpufreq: Convert to hotplug state machine
ACPI/processor: Convert to hotplug state machine
virtio scsi: Convert to hotplug state machine
oprofile/timer: Convert to hotplug state machine
block/softirq: Convert to hotplug state machine
lib/irq_poll: Convert to hotplug state machine
x86/microcode: Convert to hotplug state machine
sh/SH-X3 SMP: Convert to hotplug state machine
ia64/mca: Convert to hotplug state machine
ARM/OMAP/wakeupgen: Convert to hotplug state machine
ARM/shmobile: Convert to hotplug state machine
arm64/FP/SIMD: Convert to hotplug state machine
...
Pull RCU updates from Ingo Molnar:
"The main changes in this cycle were:
- Expedited grace-period changes, most notably avoiding having user
threads drive expedited grace periods, using a workqueue instead.
- Miscellaneous fixes, including a performance fix for lists that was
sent with the lists modifications.
- CPU hotplug updates, most notably providing exact CPU-online
tracking for RCU. This will in turn allow removal of the checks
supporting RCU's prior heuristic that was based on the assumption
that CPUs would take no longer than one jiffy to come online.
- Torture-test updates.
- Documentation updates"
* 'core-rcu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (22 commits)
list: Expand list_first_entry_or_null()
torture: TOROUT_STRING(): Insert a space between flag and message
rcuperf: Consistently insert space between flag and message
rcutorture: Print out barrier error as document says
torture: Add task state to writer-task stall printk()s
torture: Convert torture_shutdown() to hrtimer
rcutorture: Convert to hotplug state machine
cpu/hotplug: Get rid of CPU_STARTING reference
rcu: Provide exact CPU-online tracking for RCU
rcu: Avoid redundant quiescent-state chasing
rcu: Don't use modular infrastructure in non-modular code
sched: Make wake_up_nohz_cpu() handle CPUs going offline
rcu: Use rcu_gp_kthread_wake() to wake up grace period kthreads
rcu: Use RCU's online-CPU state for expedited IPI retry
rcu: Exclude RCU-offline CPUs from expedited grace periods
rcu: Make expedited RCU CPU stall warnings respond to controls
rcu: Stop disabling expedited RCU CPU stall warnings
rcu: Drive expedited grace periods from workqueue
rcu: Consolidate expedited grace period machinery
documentation: Record reason for rcu_head two-byte alignment
...
Install the callbacks via the state machine.
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Reviewed-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Pekka Enberg <penberg@kernel.org>
Cc: linux-mm@kvack.org
Cc: rt@linutronix.de
Cc: David Rientjes <rientjes@google.com>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Christoph Lameter <cl@linux.com>
Link: http://lkml.kernel.org/r/20160823125319.abeapfjapf2kfezp@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Install the callbacks via the state machine. They are installed at run time but
relay_prepare_cpu() does not need to be invoked by the boot CPU because
relay_open() was not yet invoked and there are no pools that need to be created.
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Reviewed-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: rt@linutronix.de
Cc: Andrew Morton <akpm@linux-foundation.org>
Link: http://lkml.kernel.org/r/20160818125731.27256-3-bigeasy@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
All users are converted to state machine, remove CPU_STARTING and the
corresponding CPU_DYING.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: rt@linutronix.de
Link: http://lkml.kernel.org/r/20160818125731.27256-2-bigeasy@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Some compilers are unhappy with the anon union in the state array. Replace
it with a named union.
While at it align the state array initializers proper and add the missing
name tags.
Fixes: cf392d10b6 "cpu/hotplug: Add multi instance support"
Reported-by: Ingo Molnar <mingo@kernel.org>
Reported-by: Fenguang Wu <fengguang.wu@intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: rt@linutronix.de
This patch adds the ability for a given state to have multiple
instances. Until now all states have a single instance and the startup /
teardown callback use global variables.
A few drivers need to perform a the same callbacks on multiple
"instances". Currently we have three drivers in tree which all have a
global list which they iterate over. With multi instance they support
don't need their private list and the functionality has been moved into
core code. Plus we hold the hotplug lock in core so no cpus comes/goes
while instances are registered and we do rollback in error case :)
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Will Deacon <will.deacon@arm.com>
Cc: rt@linutronix.de
Link: http://lkml.kernel.org/r/1471024183-12666-3-git-send-email-bigeasy@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This is preparation for the following patch.
This rework here changes the arguments of cpuhp_invoke_callback(). It
passes now `state' and whether `startup' or `teardown' callback should
be invoked. The callback then is looked up by the function.
The following is a clanup of callers:
- cpuhp_issue_call() has one argument less
- struct cpuhp_cpu_state (which is used by the hotplug thread) gets also
its callback removed. The decision if it is a single callback
invocation moved to the `single' variable. Also a `bringup' variable
has been added to distinguish between startup and teardown callback.
- take_cpu_down() needs to start one step earlier. We always get here
via CPUHP_TEARDOWN_CPU callback. Before that change cpuhp_ap_states +
CPUHP_TEARDOWN_CPU pointed to an empty entry because TEARDOWN is saved
in bp_states for this reason. Now that we use cpuhp_get_step() to
lookup the state we must explicitly skip it in order not to invoke it
twice.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Will Deacon <will.deacon@arm.com>
Cc: rt@linutronix.de
Link: http://lkml.kernel.org/r/1471024183-12666-2-git-send-email-bigeasy@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
disable_nonboot_cpus() assumes that the lowest numbered online CPU is
the boot CPU, and that this is the correct CPU to run any power
management code on.
On x86 this is always correct, as CPU0 cannot (easily) by taken offline.
On arm64 CPU0 can be taken offline. For hibernate/resume this means we
may hibernate on a CPU other than CPU0. If the system is rebooted with
kexec 'CPU0' will be assigned to a different physical CPU. This
complicates hibernate/resume as now we can't trust the CPU numbers.
Arch code can find the correct physical CPU, and ensure it is online
before resume from hibernate begins, but also needs to influence
disable_nonboot_cpus()s choice of CPU.
Rename disable_nonboot_cpus() as freeze_secondary_cpus() and add an
argument indicating which CPU should be left standing. Follow the logic
in migrate_to_reboot_cpu() to use the lowest numbered online CPU if the
requested CPU is not online.
Add disable_nonboot_cpus() as an inline function that has the existing
behaviour.
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: James Morse <james.morse@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
CPU_STARTING is scheduled for removal. There is no use of it in drivers
and core code uses it only for compatibility with old-style CPU-hotplug
notifiers. This patch removes therefore removes CPU_STARTING from an
RCU-related comment.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Up to now, RCU has assumed that the CPU-online process makes it from
CPU_UP_PREPARE to set_cpu_online() within one jiffy. Given the recent
rise of virtualized environments, this assumption is very clearly
obsolete. Failing to meet this deadline can result in RCU paying
attention to an incoming CPU for one jiffy, then ignoring it until the
grace period following the one in which that CPU sets itself online.
This situation might prove to be fatally disappointing to any RCU
read-side critical sections that had the misfortune to execute during
the time in which RCU was ignoring the slow-to-come-online CPU.
This commit therefore updates RCU's internal CPU state-tracking
information at notify_cpu_starting() time, thus providing RCU with
an exact transition of the CPU's state from offline to online.
Note that this means that incoming CPUs must not use RCU read-side
critical section (other than those of SRCU) until notify_cpu_starting()
time. Note also that the CPU_STARTING notifiers -are- allowed to use
RCU read-side critical sections. (Of course, CPU-hotplug notifiers are
rapidly becoming obsolete, so you need to act fast!)
If a given architecture or CPU family needs to use RCU read-side
critical sections earlier, the call to rcu_cpu_starting() from
notify_cpu_starting() will need to be architecture-specific, with
architectures that need early use being required to hand-place
the call to rcu_cpu_starting() at some point preceding the call to
notify_cpu_starting().
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Now that Xen no longer allocates irqs in _cpu_up() we can restore
commit:
a899418167 ("hotplug: Prevent alloc/free of irq descriptors during cpu up/down")
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Reviewed-by: Juergen Gross <jgross@suse.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Anna-Maria Gleixner <anna-maria@linutronix.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: david.vrabel@citrix.com
Cc: xen-devel@lists.xenproject.org
Link: http://lkml.kernel.org/r/1470244948-17674-3-git-send-email-boris.ostrovsky@oracle.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
On the tear-down path, the dead CPU callback for the timers was
misplaced within the 'cpuhp_state' enumeration. There is a hidden
dependency between the timers and block multiqueue. The timers
callback must happen before the block multiqueue callback otherwise a
RCU stall occurs.
Move the timers callback to the proper place in the state machine.
Reported-and-tested-by: Jon Hunter <jonathanh@nvidia.com>
Reported-by: kbuild test robot <lkp@intel.com>
Fixes: 24f73b9971 ("timers/core: Convert to hotplug state machine")
Signed-off-by: Richard Cochran <rcochran@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Cc: John Stultz <john.stultz@linaro.org>
Cc: rt@linutronix.de
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Link: http://lkml.kernel.org/r/1469610498-25914-1-git-send-email-rcochran@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Straight forward conversion to the state machine. Though the question arises
whether this needs really all these state transitions to work.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Anna-Maria Gleixner <anna-maria@linutronix.de>
Reviewed-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: rt@linutronix.de
Link: http://lkml.kernel.org/r/20160713153337.982013161@linutronix.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Install the callbacks via the state machine. They are installed at runtime so
smpcfd_prepare_cpu() needs to be invoked by the boot-CPU.
Signed-off-by: Richard Weinberger <richard@nod.at>
[ Added the dropped CPU dying case back in. ]
Signed-off-by: Richard Cochran <rcochran@linutronix.de>
Signed-off-by: Anna-Maria Gleixner <anna-maria@linutronix.de>
Reviewed-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Davidlohr Bueso <dave@stgolabs>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mel Gorman <mgorman@techsingularity.net>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: rt@linutronix.de
Link: http://lkml.kernel.org/r/20160713153337.818376366@linutronix.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
When tearing down, call timers_dead_cpu() before notify_dead().
There is a hidden dependency between:
- timers
- block multiqueue
- rcutree
If timers_dead_cpu() comes later than blk_mq_queue_reinit_notify()
that latter function causes a RCU stall.
Signed-off-by: Richard Cochran <rcochran@linutronix.de>
Signed-off-by: Anna-Maria Gleixner <anna-maria@linutronix.de>
Reviewed-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: rt@linutronix.de
Link: http://lkml.kernel.org/r/20160713153337.566790058@linutronix.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Split out the clockevents callbacks instead of piggybacking them on
hrtimers.
This gets rid of a POST_DEAD user. See commit:
54e88fad22 ("sched: Make sure timers have migrated before killing the migration_thread")
We just move the callback state to the proper place in the state machine.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Anna-Maria Gleixner <anna-maria@linutronix.de>
Reviewed-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: rt@linutronix.de
Link: http://lkml.kernel.org/r/20160713153337.485419196@linutronix.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Get rid of the prio ordering of the separate notifiers and use a proper state
callback pair.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Anna-Maria Gleixner <anna-maria@linutronix.de>
Reviewed-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Tejun Heo <tj@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Lai Jiangshan <jiangshanlai@gmail.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Nicolas Iooss <nicolas.iooss_linux@m4x.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: rt@linutronix.de
Link: http://lkml.kernel.org/r/20160713153335.197083890@linutronix.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Actually a nice symmetric startup/teardown pair which fits properly into
the state machine concept. In the long run we should be able to invoke
the startup callback for the boot CPU via the state machine and get
rid of the init function which invokes it on the boot CPU.
Note: This comes actually before the perf hardware callbacks. In the notifier
model the hardware callbacks have a higher priority than the core
callback. But that's solely for CPU offline so that hardware migration of
events happens before the core is notified about the outgoing CPU.
With the symetric state array model we have the following ordering:
UP: core -> hardware
DOWN: hardware -> core
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Anna-Maria Gleixner <anna-maria@linutronix.de>
Reviewed-by: Sebastian Siewior <bigeasy@linutronix.de>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Cc: rt@linutronix.de
Link: http://lkml.kernel.org/r/20160713153333.587514098@linutronix.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
We switched the hotplug machinery to smpboot threads. Early registration of
hotplug callbacks, i.e. from do_pre_smp_initcalls(), happens before the
threads are initialized. Instead of moving the thread init, we simply handle
it in the hotplug code itself and invoke the function directly.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Anna-Maria Gleixner <anna-maria@linutronix.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: rt@linutronix.de
Link: http://lkml.kernel.org/r/20160713153332.896450738@linutronix.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Xiaolong Ye reported lock debug warnings triggered by the following commit:
8de4a0066106 ("perf/x86: Convert the core to the hotplug state machine")
The bug is the following: the cpuhp_bp_states[] array is cut short when
CONFIG_SMP=n, but the dynamically registered callbacks are stored nevertheless
and happily scribble outside of the array bounds...
We need to store them in case that the state is unregistered so we can invoke
the teardown function. That's independent of CONFIG_SMP. Make sure the array
is large enough.
Reported-by: kernel test robot <xiaolong.ye@intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Adam Borowski <kilobyte@angband.pl>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Anna-Maria Gleixner <anna-maria@linutronix.de>
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Borislav Petkov <bp@suse.de>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Kan Liang <kan.liang@intel.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Stephane Eranian <eranian@google.com>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Cc: lkp@01.org
Cc: stable@vger.kernel.org
Cc: tipbuild@zytor.com
Fixes: cff7d378d3 "cpu/hotplug: Convert to a state machine for the control processor"
Link: http://lkml.kernel.org/r/alpine.DEB.2.11.1607122144560.4083@nanos
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The scheduler can handle per cpu threads before the cpu is set to active and
it does not allow user space threads on the cpu before active is
set. Attaching to the scheduling domains is also not required before user
space threads can be handled.
Move the activation to the end of the hotplug state space. That also means
that deactivation is the first action when a cpu is shut down.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Peter Zijlstra <peterz@infradead.org>
Cc: rt@linutronix.de
Link: http://lkml.kernel.org/r/20160310120025.597477199@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The sync_rcu stuff is specificically for clearing bits in the active
mask, such that everybody will observe the bit cleared and will not
consider the cleared CPU for load-balancing etc.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: rt@linutronix.de
Link: http://lkml.kernel.org/r/20160310120025.169219710@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Now that we reduced everything into single notifiers, it's simple to move them
into the hotplug state machine space.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Peter Zijlstra <peterz@infradead.org>
Cc: rt@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Start distangling the maze of hotplug notifiers in the scheduler.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Peter Zijlstra <peterz@infradead.org>
Cc: rt@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The recent introduction of the hotplug thread which invokes the callbacks on
the plugged cpu, cased the following regression:
If takedown_cpu() fails, then we run into several issues:
1) The rollback of the target cpu states is not invoked. That leaves the smp
threads and the hotplug thread in disabled state.
2) notify_online() is executed due to a missing skip_onerr flag. That causes
that both CPU_DOWN_FAILED and CPU_ONLINE notifications are invoked which
confuses quite some notifiers.
3) The CPU_DOWN_FAILED notification is not invoked on the target CPU. That's
not an issue per se, but it is inconsistent and in consequence blocks the
patches which rely on these states being invoked on the target CPU and not
on the controlling cpu. It also does not preserve the strict call order on
rollback which is problematic for the ongoing state machine conversion as
well.
To fix this we add a rollback flag to the remote callback machinery and invoke
the rollback including the CPU_DOWN_FAILED notification on the remote
cpu. Further mark the notify online state with 'skip_onerr' so we don't get a
double invokation.
This workaround will go away once we moved the unplug invocation to the target
cpu itself.
[ tglx: Massaged changelog and moved the CPU_DOWN_FAILED notifiaction to the
target cpu ]
Fixes: 4cb28ced23 ("cpu/hotplug: Create hotplug threads")
Reported-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: linux-s390@vger.kernel.org
Cc: rt@linutronix.de
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Anna-Maria Gleixner <anna-maria@linutronix.de>
Link: http://lkml.kernel.org/r/20160408124015.GA21960@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Commit 931ef16330 moved the smpboot thread park/unpark invocation to the
state machine. The move of the unpark invocation was premature as it depends
on work in progress patches.
As a result cpu down can fail, because rcu synchronization in takedown_cpu()
eventually requires a functional softirq thread. I never encountered the
problem in testing, but 0day testing managed to provide a reliable reproducer.
Remove the smpboot_threads_park() call from the state machine for now and put
it back into the original place after the rcu synchronization.
I'm embarrassed as I knew about the dependency and still managed to get it
wrong. Hotplug induced brain melt seems to be the only sensible explanation
for that.
Fixes: 931ef16330 "cpu/hotplug: Unpark smpboot threads from the state machine"
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
The check for the AP range in cpuhp_is_ap_state() is redundant after commit
8df3e07e7f "cpu/hotplug: Let upcoming cpu bring itself fully up" because all
states above CPUHP_BRINGUP_CPU are invoked on the hotplugged cpu. Remove it.
Reported-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Paul noticed that the conversion of the death reporting introduced a race
where the outgoing cpu might be delayed after waking the controll processor,
so it might not be able to call rcu_report_dead() before being physically
removed, leading to RCU stalls.
We cant call complete after rcu_report_dead(), so instead of going back to
busy polling, simply issue a function call to do the completion.
Fixes: 27d50c7eeb "rcu: Make CPU_DYING_IDLE an explicit call"
Reported-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Link: http://lkml.kernel.org/r/20160302201127.GA23440@linux.vnet.ibm.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Peter Zijlstra <peterz@infradead.org>
Make the RCU CPU_DYING_IDLE callback an explicit function call, so it gets
invoked at the proper place.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-arch@vger.kernel.org
Cc: Rik van Riel <riel@redhat.com>
Cc: Rafael Wysocki <rafael.j.wysocki@intel.com>
Cc: "Srivatsa S. Bhat" <srivatsa@mit.edu>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Sebastian Siewior <bigeasy@linutronix.de>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Paul McKenney <paulmck@linux.vnet.ibm.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Paul Turner <pjt@google.com>
Link: http://lkml.kernel.org/r/20160226182341.870167933@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Kill the busy spinning on the control side and just wait for the hotplugged
cpu to tell that it reached the dead state.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-arch@vger.kernel.org
Cc: Rik van Riel <riel@redhat.com>
Cc: Rafael Wysocki <rafael.j.wysocki@intel.com>
Cc: "Srivatsa S. Bhat" <srivatsa@mit.edu>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Sebastian Siewior <bigeasy@linutronix.de>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Paul McKenney <paulmck@linux.vnet.ibm.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Paul Turner <pjt@google.com>
Link: http://lkml.kernel.org/r/20160226182341.776157858@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Let the upcoming cpu kick the hotplug thread and let itself complete the
bringup. That way the controll side can just wait for the completion or later
when we made the hotplug machinery async not care at all.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-arch@vger.kernel.org
Cc: Rik van Riel <riel@redhat.com>
Cc: Rafael Wysocki <rafael.j.wysocki@intel.com>
Cc: "Srivatsa S. Bhat" <srivatsa@mit.edu>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Sebastian Siewior <bigeasy@linutronix.de>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Paul McKenney <paulmck@linux.vnet.ibm.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Paul Turner <pjt@google.com>
Link: http://lkml.kernel.org/r/20160226182341.697655464@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Let the hotplugged cpu invoke the setup/teardown callbacks
(CPU_ONLINE/CPU_DOWN_PREPARE) itself.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-arch@vger.kernel.org
Cc: Rik van Riel <riel@redhat.com>
Cc: Rafael Wysocki <rafael.j.wysocki@intel.com>
Cc: "Srivatsa S. Bhat" <srivatsa@mit.edu>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Sebastian Siewior <bigeasy@linutronix.de>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Paul McKenney <paulmck@linux.vnet.ibm.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Paul Turner <pjt@google.com>
Link: http://lkml.kernel.org/r/20160226182341.536364371@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
In order to let the hotplugged cpu take care of the setup/teardown, we need a
seperate hotplug thread.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-arch@vger.kernel.org
Cc: Rik van Riel <riel@redhat.com>
Cc: Rafael Wysocki <rafael.j.wysocki@intel.com>
Cc: "Srivatsa S. Bhat" <srivatsa@mit.edu>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Sebastian Siewior <bigeasy@linutronix.de>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Paul McKenney <paulmck@linux.vnet.ibm.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Paul Turner <pjt@google.com>
Link: http://lkml.kernel.org/r/20160226182341.454541272@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
We need that for running callbacks on the AP and the BP.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-arch@vger.kernel.org
Cc: Rik van Riel <riel@redhat.com>
Cc: Rafael Wysocki <rafael.j.wysocki@intel.com>
Cc: "Srivatsa S. Bhat" <srivatsa@mit.edu>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Sebastian Siewior <bigeasy@linutronix.de>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Paul McKenney <paulmck@linux.vnet.ibm.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Paul Turner <pjt@google.com>
Link: http://lkml.kernel.org/r/20160226182341.374946234@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Handle the smpboot threads in the state machine.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-arch@vger.kernel.org
Cc: Rik van Riel <riel@redhat.com>
Cc: Rafael Wysocki <rafael.j.wysocki@intel.com>
Cc: "Srivatsa S. Bhat" <srivatsa@mit.edu>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Sebastian Siewior <bigeasy@linutronix.de>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Paul McKenney <paulmck@linux.vnet.ibm.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Paul Turner <pjt@google.com>
Link: http://lkml.kernel.org/r/20160226182341.295777684@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Move the scheduler cpu online notifier part to the hotplug core. This is
anyway the highest priority callback and we need that functionality right now
for the next changes.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-arch@vger.kernel.org
Cc: Rik van Riel <riel@redhat.com>
Cc: Rafael Wysocki <rafael.j.wysocki@intel.com>
Cc: "Srivatsa S. Bhat" <srivatsa@mit.edu>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Sebastian Siewior <bigeasy@linutronix.de>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Paul McKenney <paulmck@linux.vnet.ibm.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Paul Turner <pjt@google.com>
Link: http://lkml.kernel.org/r/20160226182341.200791046@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Implement function which allow to setup/remove hotplug state callbacks.
The default behaviour for setup is to call the startup function for this state
for (or on) all cpus which have a hotplug state >= the installed state.
The default behaviour for removal is to call the teardown function for this
state for (or on) all cpus which have a hotplug state >= the installed state.
This includes rollback to the previous state in case of failure.
A special state is CPUHP_ONLINE_DYN. Its for dynamically registering a hotplug
callback pair. This is for drivers which have no dependencies to avoid that we
need to allocate CPUHP states for each of them
For both setup and remove helper functions are provided, which prevent the
core to issue the callbacks. This simplifies the conversion of existing
hotplug notifiers.
[ Dynamic registering implemented by Sebastian Siewior ]
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-arch@vger.kernel.org
Cc: Rik van Riel <riel@redhat.com>
Cc: Rafael Wysocki <rafael.j.wysocki@intel.com>
Cc: "Srivatsa S. Bhat" <srivatsa@mit.edu>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Sebastian Siewior <bigeasy@linutronix.de>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Paul McKenney <paulmck@linux.vnet.ibm.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Paul Turner <pjt@google.com>
Link: http://lkml.kernel.org/r/20160226182341.103464877@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Make it possible to write a target state to the per cpu state file, so we can
switch between states.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-arch@vger.kernel.org
Cc: Rik van Riel <riel@redhat.com>
Cc: Rafael Wysocki <rafael.j.wysocki@intel.com>
Cc: "Srivatsa S. Bhat" <srivatsa@mit.edu>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Sebastian Siewior <bigeasy@linutronix.de>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Paul McKenney <paulmck@linux.vnet.ibm.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Paul Turner <pjt@google.com>
Link: http://lkml.kernel.org/r/20160226182341.022814799@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Add a sysfs interface so we can actually see in which state the cpus are in.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-arch@vger.kernel.org
Cc: Rik van Riel <riel@redhat.com>
Cc: Rafael Wysocki <rafael.j.wysocki@intel.com>
Cc: "Srivatsa S. Bhat" <srivatsa@mit.edu>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Sebastian Siewior <bigeasy@linutronix.de>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Paul McKenney <paulmck@linux.vnet.ibm.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Paul Turner <pjt@google.com>
Link: http://lkml.kernel.org/r/20160226182340.942257522@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
We want to be able to bringup/teardown the cpu to a particular state. Add a
target argument to _cpu_up/down.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-arch@vger.kernel.org
Cc: Rik van Riel <riel@redhat.com>
Cc: Rafael Wysocki <rafael.j.wysocki@intel.com>
Cc: "Srivatsa S. Bhat" <srivatsa@mit.edu>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Sebastian Siewior <bigeasy@linutronix.de>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Paul McKenney <paulmck@linux.vnet.ibm.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Paul Turner <pjt@google.com>
Link: http://lkml.kernel.org/r/20160226182340.862113133@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Move the functions which need to run on the hotplugged processor into
a state machine array and let the code iterate through these functions.
In a later state, this will grow synchronization points between the
control processor and the hotplugged processor, so we can move the
various architecture implementations of the synchronizations to the
core.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-arch@vger.kernel.org
Cc: Rik van Riel <riel@redhat.com>
Cc: Rafael Wysocki <rafael.j.wysocki@intel.com>
Cc: "Srivatsa S. Bhat" <srivatsa@mit.edu>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Sebastian Siewior <bigeasy@linutronix.de>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Paul McKenney <paulmck@linux.vnet.ibm.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Paul Turner <pjt@google.com>
Link: http://lkml.kernel.org/r/20160226182340.770651526@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Move the split out steps into a callback array and let the cpu_up/down
code iterate through the array functions. For now most of the
callbacks are asymmetric to resemble the current hotplug maze.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-arch@vger.kernel.org
Cc: Rik van Riel <riel@redhat.com>
Cc: Rafael Wysocki <rafael.j.wysocki@intel.com>
Cc: "Srivatsa S. Bhat" <srivatsa@mit.edu>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Sebastian Siewior <bigeasy@linutronix.de>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Paul McKenney <paulmck@linux.vnet.ibm.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Paul Turner <pjt@google.com>
Link: http://lkml.kernel.org/r/20160226182340.671816690@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Split cpu_down in separate functions in preparation for state machine
conversion.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-arch@vger.kernel.org
Cc: Rik van Riel <riel@redhat.com>
Cc: Rafael Wysocki <rafael.j.wysocki@intel.com>
Cc: "Srivatsa S. Bhat" <srivatsa@mit.edu>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Sebastian Siewior <bigeasy@linutronix.de>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Paul McKenney <paulmck@linux.vnet.ibm.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Paul Turner <pjt@google.com>
Link: http://lkml.kernel.org/r/20160226182340.511796562@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Split out into separate functions, so we can convert it to a state machine.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-arch@vger.kernel.org
Cc: Rik van Riel <riel@redhat.com>
Cc: Rafael Wysocki <rafael.j.wysocki@intel.com>
Cc: "Srivatsa S. Bhat" <srivatsa@mit.edu>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Sebastian Siewior <bigeasy@linutronix.de>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Paul McKenney <paulmck@linux.vnet.ibm.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Paul Turner <pjt@google.com>
Link: http://lkml.kernel.org/r/20160226182340.429389195@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Thomas Gleixner