Sync code to the same with tk4 pub/lts/0017-kabi, except deleted rue
and wujing. Partners can submit pull requests to this branch, and we
can pick the commits to tk4 pub/lts/0017-kabi easly.
Signed-off-by: Jianping Liu <frankjpliu@tencent.com>
Gitee limit the repo's size to 3GB, to reduce the size of the code,
sync codes to ock 5.4.119-20.0009.21 in one commit.
Signed-off-by: Jianping Liu <frankjpliu@tencent.com>
Sync kernel codes to the same with 590eaf1fec ("Init Repo base on
linux 5.4.32 long term, and add base tlinux kernel interfaces."), which
is from tk4, and it is the base of tk4.
Signed-off-by: Jianping Liu <frankjpliu@tencent.com>
Starting from DWC_usb31 version 1.90a and later, the DCTL.CSFRST bit
will not be cleared until after all the internal clocks are synchronized
during soft-reset. This may take a little more than 50ms. Set the
polling rate at 20ms instead.
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The member @lock of dwc3_ep struct is only initialized,
and not used elsewhere, so remove it.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Gadget applications may have a requirement to disable the U1 and U2
entry based on the usecase. Below are few usecases where the disabling
U1/U2 entries may be possible.
Usecase 1:
When combining dwc3 with an redriver for a USB Type-C device solution, it
sometimes have problems with leaving U1/U2 for certain hosts, resulting in
link training errors and reconnects. For this U1/U2 state entries may be
avoided.
Usecase 2:
When performing performance benchmarking on mass storage gadget the
U1 and U2 entries can be disabled.
Usecase 3:
When periodic transfers like ISOC transfers are used with bInterval
of 1 which doesn't require the link to enter into U1 or U2 state entry
(since ping is issued from host for every uframe interval). In this
case the U1 and U2 entry can be disabled.
Disablement of U1/U2 can be done by setting U1DevExitLat and U2DevExitLat
values to 0 in the BOS descriptor. Host on seeing 0 value for U1DevExitLat
and U2DevExitLat, it doesn't send SET_SEL requests to the gadget. There
may be some hosts which may send SET_SEL requests even after seeing 0 in
the UxDevExitLat of BOS descriptor. To aviod U1/U2 entries for these type
of hosts, dwc3 controller can be programmed to reject those U1/U2 requests
by not enabling ACCEPTUxENA bits in DCTL register.
This patch updates the same.
Signed-off-by: Anurag Kumar Vulisha <anurag.kumar.vulisha@xilinx.com>
Signed-off-by: Claus H. Stovgaard <cst@phaseone.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The macro name DWC3_DCTL_LPM_ERRATA is uninformative and does not do
masking. Remove DWC3_DCTL_LPM_ERRATA_MASK and rename
DWC3_DCTL_LPM_ERRATA to DWC3_DCTL_NYET_THRES with proper masking.
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Now that we modified the code to fix a race condition, it's clear that
DWC3_EP_END_TRANSFER_PENDING is unnecessary, considering that
DWC3_EP_TRANSFER_STARTED will remain set until End Transfer completes.
Tested-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Now that we have req->status, we don't need this extra flag
anymore. It's safe to remove it.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This patch starts tracking dwc3_request status. A following patch will
build on top of this to prevent a request from being queued twice.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Implement the new frame_number API to report the isochronous interval
frame number. This patch checks and reports the interval in which the
isoc transfer was transmitted or received via the Isoc-First TRB SOF
number field.
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Gadget driver may take an unbounded amount of time to queue requests
after XferNotReady. This is important for isochronous endpoints which
need to be started for a specific (micro-)frame.
If we fail to start a transfer for isochronous endpoint, let's try
queueing to a future interval and see if that helps. We will stop trying
if we fail a start transfer for 5 intervals in the future.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Now that we have a list of cancelled requests, we can skip over TRBs
when END_TRANSFER command completes.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Both flags are used for the same purpose in dwc3: appending an extra
TRB at the end to deal with controller requirements. By combining both
flags into one, we make it clear that the situation is the same and
that they should be treated equally.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
In DWC_usb31 version 1.70a-ea06 and prior, for highspeed and fullspeed
isochronous IN, BIT[15:14] of the 16-bit microframe number reported by
the XferNotReady event are invalid. The driver uses this number to
schedule the isochronous transfer and passes it to the START TRANSFER
command. Because this number is invalid, the command may fail. If
BIT[15:14] matches the internal 16-bit microframe, the START TRANSFER
command will pass and the transfer will start at the scheduled time, if
it is off by 1, the command will still pass, but the transfer will start
2 seconds in the future. For all other conditions, the START TRANSFER
command will fail with bus-expiry.
In order to workaround this issue, we can test for the correct
combination of BIT[15:14] by sending START TRANSFER commands with
different values of BIT[15:14]: 'b00, 'b01, 'b10, and 'b11. Each
combination is 2^14 uframe apart (or 2 seconds). 4 seconds into the
future will result in a bus-expiry status. As the result, within the 4
possible combinations for BIT[15:14], there will be 2 successful and 2
failure START COMMAND status. One of the 2 successful command status
will result in a 2-second delay start. The smaller BIT[15:14] value is
the correct combination.
Since there are only 4 outcomes and the results are ordered, we can
simply test 2 START TRANSFER commands with BIT[15:14] combinations 'b00
and 'b01 to deduce the smaller successful combination.
Let test0 = test status for combination 'b00 and test1 = test status for
'b01 of BIT[15:14]. The correct combination is as follow:
if test0 fails and test1 passes, BIT[15:14] is 'b01
if test0 fails and test1 fails, BIT[15:14] is 'b10
if test0 passes and test1 fails, BIT[15:14] is 'b11
if test0 passes and test1 passes, BIT[15:14] is 'b00
Synopsys STAR 9001202023: Wrong microframe number for isochronous IN
endpoints.
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Add a new field to dwc3 structure to track VERSIONTYPE. The VERSIONTYPE
is represented in ASCII in the 32-bit VERSIONTYPE register. In
DWC_usb31, sub releases for each version are tracked with VERSIONTYPE
such as "ea01" and "ea02".
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
DWC_usb31 and DWC_usb3 v3.30a and higher do not support OTG mode. If
the controller supports DRD but the dr_mode is not specified or set to
OTG, then set the mode to peripheral.
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Support the option to disable USB2 LPM. Set xhci "usb2-lpm-disable"
property via "snps,usb2-lpm-disable" property.
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
To dump internal LSP and endpoint state debug registers, we must write
to GDBGLSPMUX register. This patch correctly dump LSP and endpoint
states from the debug registers.
If the controller is in device mode, all LSP and endpoint state
registers will be dumped via the debugfs attribute "lsp_dump". In host
mode, the user has to write the LSP number to "lsp_dump" to dump a
specific LSP selection.
Fixes: 80b776340c ("usb: dwc3: Dump LSP and BMU debug info")
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The Tx/RxFIFO types in the GDBGFIFOSPACE.FIFO_QUEUE_SELECT are not
queue. Properly rename them.
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
By default when core sees any transaction error (CRC or overflow) it
replies with terminating retry ACK (Retry=1 and Nump == 0).
Enabling this Auto Retry feature in controller will make the core send
a non-terminanting ACK upon such transaction errors. That is, ACK TP
with Retry=1 and Nump != 0.
Doing so will give controller a chance to recover from transient error
conditions.
Signed-off-by: Anurag Kumar Vulisha <anurag.kumar.vulisha@xilinx.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Enable the undefined length INCR burst type and set INCRx.
Different platform may has the different burst size type.
In order to get best performance, we need to tune the burst
size to one special value, instead of the default value.
Signed-off-by: Changming Huang <jerry.huang@nxp.com>
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
Signed-off-by: Pengbo Mu <pengbo.mu@nxp.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Add the macro definition for global soc bus configuration
register 0
Signed-off-by: Changming Huang <jerry.huang@nxp.com>
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
Signed-off-by: Pengbo Mu <pengbo.mu@nxp.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Now, this part of the code is duplicated and brings no extra value to
the driver. Let's remove it.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
In case we get an event with status set to Missed Isoc, this means we
have missed an isochronous interval and should issue End Transfer
command and wait for the following XferNotReady.
Let's do that early, rather than late.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The present code correctly fetches the req which were previously not
queued from the started_list but fails to continue queuing from the sg
where it previously stopped queuing (because of the unavailable TRB's).
This patch correct's the code to continue queuing from the correct sg
present in the sglist.
For example, consider 5 sgs in req. Because of limited TRB's among the
5 sgs only 3 got queued. This patch corrects the code to start queuing
from correct sg i.e 4th sg when the TRBs are available.
Signed-off-by: Anurag Kumar Vulisha <anuragku@xilinx.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The code logic in dwc3_prepare_one_trb() incorrectly uses the address
and length fields present in req packet for mapping TRB's instead of
using the address and length fields of scattergather lists. This patch
correct's the code to use sg->address and sg->length when scattergather
lists are present.
Signed-off-by: Anurag Kumar Vulisha <anuragku@xilinx.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Historically, the clocks and resets are handled on the glue layer
side instead of the DWC3 core. For simple cases, dwc3-of-simple.c
takes care of arbitrary number of clocks and resets. The DT node
structure typically looks like as follows:
dwc3-glue {
compatible = "foo,dwc3";
clocks = ...;
resets = ...;
...
dwc3 {
compatible = "snps,dwc3";
...
};
}
By supporting the clocks and the reset in the dwc3/core.c, it will
be turned into a single node:
dwc3 {
compatible = "foo,dwc3", "snps,dwc3";
clocks = ...;
resets = ...;
...
}
This commit adds the binding of clocks and resets specific to this IP.
The number of clocks should generally be the same across SoCs, it is
just some SoCs either tie clocks together or do not provide software
control of some of the clocks.
I took the clock names from the Synopsys datasheet: "ref" (ref_clk),
"bus_early" (bus_clk_early), and "suspend" (suspend_clk).
I found only one reset line in the datasheet, hence the reset-names
property is omitted.
Those clocks are required for new platforms. Enforcing the new
binding breaks existing platforms since they specify clocks (and
resets) in their glue layer node, but nothing in the core node.
I listed such exceptional cases in the DT binding. The driver
code has been relaxed to accept no clock. This change is based
on the discussion [1].
I inserted reset_control_deassert() and clk_bulk_enable() before the
first register access, i.e. dwc3_cache_hwparams().
[1] https://patchwork.kernel.org/patch/10284265/
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Check and configure TX/RX threshold for DWC_usb31. Update dwc3 structure
with new fields to store these threshold configurations.
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Update two GTXFIFOSIZ bit fields for the DWC_usb31 controller. TXFDEP
is a 15-bit value instead of 16-bit value, and bit 15 is TXFRAMNUM.
The GTXFIFOSIZ register for DWC_usb31 is as follows:
+-------+-----------+----------------------------------+
| BITS | Name | Description |
+=======+===========+==================================+
| 31:16 | TXFSTADDR | Transmit FIFOn RAM Start Address |
| 15 | TXFRAMNUM | Asynchronous/Periodic TXFIFO |
| 14:0 | TXFDEP | TXFIFO Depth |
+-------+-----------+----------------------------------+
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This is useful on platforms (e.g. TI AM437x) that don't
have ID available on a GPIO but do have the OTG block.
We can obtain the ID state via the OTG block and use it
for dual-role switching.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
In order for ULPI PHYs to work, dwc3_phy_setup() and dwc3_ulpi_init()
must be doene before dwc3_core_get_phy().
commit 541768b08a ("usb: dwc3: core: Call dwc3_core_get_phy() before initializing phys")
broke this.
The other issue is that dwc3_core_get_phy() and dwc3_ulpi_init() should
be called only once during the life cycle of the driver. However,
as dwc3_core_init() is called during system suspend/resume it will
result in multiple calls to dwc3_core_get_phy() and dwc3_ulpi_init()
which is wrong.
Fix this by moving dwc3_ulpi_init() out of dwc3_phy_setup()
into dwc3_core_ulpi_init(). Use a flag 'ulpi_ready' to ensure that
dwc3_core_ulpi_init() is called only once from dwc3_core_init().
Use another flag 'phys_ready' to call dwc3_core_get_phy() only once from
dwc3_core_init().
Fixes: 541768b08a ("usb: dwc3: core: Call dwc3_core_get_phy() before initializing phys")
Fixes: f54edb539c ("usb: dwc3: core: initialize ULPI before trying to get the PHY")
Cc: linux-stable <stable@vger.kernel.org> # >= v4.13
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The FIFO/Queue type values are incorrect. Correct them according to
DWC_usb3 programming guide section 1.2.27 (or DWC_usb31 section 1.2.25).
Additionally, this patch includes ProtocolStatusQ and AuxEventQ types.
Fixes: cf6d867d3b ("usb: dwc3: core: add fifo space helper")
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Some platforms (e.g. TI's DRA7 USB2 instance) have more trouble
with the metastability workaround as it supports only
a High-Speed PHY and the PHY can enter into an Erratic state [1]
when the controller is set in SuperSpeed mode as part of
the metastability workaround.
This causes upto 2 seconds delay in enumeration on DRA7's USB2
instance in gadget mode.
If these platforms can be better off without the workaround,
provide a device tree property to suggest that so the workaround
is avoided.
[1] Device mode enumeration trace showing PHY Erratic Error.
irq/90-dwc3-969 [000] d... 52.323145: dwc3_event: event (00000901): Erratic Error [U0]
irq/90-dwc3-969 [000] d... 52.560646: dwc3_event: event (00000901): Erratic Error [U0]
irq/90-dwc3-969 [000] d... 52.798144: dwc3_event: event (00000901): Erratic Error [U0]
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Instead of keeping our own isoch_delay, let's make use of the newly
introduced isoch_delay member in struct usb_gadget. The benefit here
is that we would be using a generic "API" which other UDCs can use,
resulting in a common setup for gadget drivers who may be interested
in Isoch Delay value.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Now that the SPDX tag is in all USB files, that identifies the license
in a specific and legally-defined manner. So the extra GPL text wording
can be removed as it is no longer needed at all.
This is done on a quest to remove the 700+ different ways that files in
the kernel describe the GPL license text. And there's unneeded stuff
like the address (sometimes incorrect) for the FSF which is never
needed.
No copyright headers or other non-license-description text was removed.
Cc: Kukjin Kim <kgene@kernel.org>
Cc: Krzysztof Kozlowski <krzk@kernel.org>
Cc: Patrice Chotard <patrice.chotard@st.com>
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It's good to have SPDX identifiers in all files to make it easier to
audit the kernel tree for correct licenses.
Update the drivers/usb/ and include/linux/usb* files with the correct
SPDX license identifier based on the license text in the file itself.
The SPDX identifier is a legally binding shorthand, which can be used
instead of the full boiler plate text.
This work is based on a script and data from Thomas Gleixner, Philippe
Ombredanne, and Kate Stewart.
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Kate Stewart <kstewart@linuxfoundation.org>
Cc: Philippe Ombredanne <pombredanne@nexb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Acked-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds a quirk to disable USB 2.0 MAC linestate check
during HS transmit. Refer the dwc3 databook, we can use it for
some special platforms if the linestate not reflect the expected
line state(J) during transmission.
When use this quirk, the controller implements a fixed 40-bit
TxEndDelay after the packet is given on UTMI and ignores the
linestate during the transmit of a token (during token-to-token
and token-to-data IPGAP).
On some rockchip platforms (e.g. rk3399), it requires to disable
the u2mac linestate check to decrease the SSPLIT token to SETUP
token inter-packet delay from 566ns to 466ns, and fix the issue
that FS/LS devices not recognized if inserted through USB 3.0 HUB.
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Guenter Roeck <groeck@chromium.org>
Signed-off-by: William Wu <william.wu@rock-chips.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
If dr_mode is "otg" then support dual role mode of operation.
Currently this mode is only supported when an extcon handle is
present in the dwc3 device tree node. This is needed to
get the ID status events of the port.
We're using a workqueue to manage the dual-role state transitions
as the extcon notifier (dwc3_drd_notifier) is called in an atomic
context by extcon_sync() and this doesn't go well with
usb_del_gadget_udc() causing a lockdep and softirq warning.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
We can't have both Host and Peripheral roles active at the same time
because of one detail on DWC3: it shares the same memory area for both
Host and Peripheral registers.
When swapping roles we must reinitialize the new role every
time. Let's make sure this works for our debugfs interface.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Jianping Liu