OverCurrent condition is not standardized in the UHCI spec.
Zhaoxin UHCI controllers report OverCurrent bit active off.
In order to handle OverCurrent condition correctly, the uhci-hcd
driver needs to be told to expect the active-off behavior.
Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable@vger.kernel.org
Signed-off-by: Weitao Wang <WeitaoWang-oc@zhaoxin.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20230423105952.4526-1-WeitaoWang-oc@zhaoxin.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: LeoLiu-oc <leoliu-oc@zhaoxin.com>
mainline inclusion
from mainline-v6.4-rc5
commit <d5e234ff08a45a7a08a52173ed793b3c125ab88d>
-------------------
Add U1/U2 feature support of xHCI for ZHAOXIN.
Since both INTEL and ZHAOXIN need to check the tier where the device is
located to determine whether to enabled U1/U2, remove the previous INTEL
U1/U2 tier policy and add common policy in xhci_check_tier_policy.
If vendor has specific U1/U2 enable policy,quirks can be add to declare.
Suggested-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Weitao Wang <WeitaoWang-oc@zhaoxin.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Message-ID: <20230602144009.1225632-12-mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: leoliu-oc <leoliu-oc@zhaoxin.com>
mainline inclusion
from mainline-v6.4-rc5
commit <d9b0328d0b8b8298dfdc97cd8e0e2371d4bcc97b>
-------------------
Some ZHAOXIN xHCI controllers follow usb3.1 spec, but only support
gen1 speed 5Gbps. While in Linux kernel, if xHCI suspport usb3.1,
root hub speed will show on 10Gbps.
To fix this issue of ZHAOXIN xHCI platforms, read usb speed ID
supported by xHCI to determine root hub speed. And add a quirk
XHCI_ZHAOXIN_HOST for this issue.
[fix warning about uninitialized symbol -Mathias]
Suggested-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Weitao Wang <WeitaoWang-oc@zhaoxin.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Message-ID: <20230602144009.1225632-11-mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: leoliu-oc <leoliu-oc@zhaoxin.com>
mainline inclusion
from mainline-v6.4-rc5
commit <2a865a652299f5666f3b785cbe758c5f57453036>
-------------------
On some ZHAOXIN hosts, xHCI will prefetch TRB for performance
improvement. However this TRB prefetch mechanism may cross page boundary,
which may access memory not allocated by xHCI driver. In order to fix
this issue, two pages was allocated for a segment and only the first
page will be used. And add a quirk XHCI_ZHAOXIN_TRB_FETCH for this issue.
Cc: stable@vger.kernel.org
Signed-off-by: Weitao Wang <WeitaoWang-oc@zhaoxin.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Message-ID: <20230602144009.1225632-10-mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: leoliu-oc <leoliu-oc@zhaoxin.com>
mainline inclusion
from mainline-v6.4-rc5
commit <f927728186f0de1167262d6a632f9f7e96433d1a>
-------------------
On ZHAOXIN ZX-100 project, xHCI can't work normally after resume
from system Sx state. To fix this issue, when resume from system
Sx state, reinitialize xHCI instead of restore.
So, Add XHCI_RESET_ON_RESUME quirk for ZX-100 to fix issue of
resuming from system Sx state.
Cc: stable@vger.kernel.org
Signed-off-by: Weitao Wang <WeitaoWang-oc@zhaoxin.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Message-ID: <20230602144009.1225632-9-mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: leoliu-oc <leoliu-oc@zhaoxin.com>
Sync code to the same with tk4 pub/lts/0017-kabi, except deleted rue
and wujing. Partners can submit pull requests to this branch, and we
can pick the commits to tk4 pub/lts/0017-kabi easly.
Signed-off-by: Jianping Liu <frankjpliu@tencent.com>
Gitee limit the repo's size to 3GB, to reduce the size of the code,
sync codes to ock 5.4.119-20.0009.21 in one commit.
Signed-off-by: Jianping Liu <frankjpliu@tencent.com>
Sync kernel codes to the same with 590eaf1fec ("Init Repo base on
linux 5.4.32 long term, and add base tlinux kernel interfaces."), which
is from tk4, and it is the base of tk4.
Signed-off-by: Jianping Liu <frankjpliu@tencent.com>
When disabling an endpoint which has cancelled requests, we should
make sure to giveback requests that are currently pending in the
cancelled list, otherwise we may fall into a situation where command
completion interrupt fires after endpoint has been disabled, therefore
causing a splat.
Fixes: fec9095bde "usb: dwc3: gadget: remove wait_end_transfer"
Reported-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Link: https://lore.kernel.org/r/20191031090713.1452818-1-felipe.balbi@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
EP_CLAIMED flag is used to track the claimed endpoints. While unloading the
module, Reset EP_CLAIMED flag for all enabled endpoints. So that it can be
reused.
Signed-off-by: Sanket Parmar <sparmar@cadence.com>
Acked-by: Peter Chen <peter.chen@nxp.com>
Reviewed-by: Roger Quadros <rogerq@ti.com>
Acked-by: Felipe Balbi <balbi@kernel.org>
Link: https://lore.kernel.org/r/20191029122441.5816-1-sparmar@cadence.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add missing endianness conversion when setting the line speed so that
this driver might work also on big-endian machines.
Also use an unsigned format specifier in the corresponding debug
message.
Signed-off-by: Johan Hovold <johan@kernel.org>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20191029102354.2733-3-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix a user-controlled slab buffer overflow due to a missing sanity check
on the bulk-out transfer buffer used for control requests.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20191029102354.2733-2-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Endpoints with a maxpacket length of 0 are probably useless. They
can't transfer any data, and it's not at all unlikely that a UDC will
crash or hang when trying to handle a non-zero-length usb_request for
such an endpoint. Indeed, dummy-hcd gets a divide error when trying
to calculate the remainder of a transfer length by the maxpacket
value, as discovered by the syzbot fuzzer.
Currently the gadget core does not check for endpoints having a
maxpacket value of 0. This patch adds a check to usb_ep_enable(),
preventing such endpoints from being used.
As far as I know, none of the gadget drivers in the kernel tries to
create an endpoint with maxpacket = 0, but until now there has been
nothing to prevent userspace programs under gadgetfs or configfs from
doing it.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-and-tested-by: syzbot+8ab8bf161038a8768553@syzkaller.appspotmail.com
CC: <stable@vger.kernel.org>
Acked-by: Felipe Balbi <balbi@kernel.org>
Link: https://lore.kernel.org/r/Pine.LNX.4.44L0.1910281052370.1485-100000@iolanthe.rowland.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 3ae62a4209 ("UAS: fix alignment of scatter/gather segments"),
copying a similar commit for usb-storage, attempted to solve a problem
involving scatter-gather I/O and USB/IP by setting the
virt_boundary_mask for mass-storage devices.
However, it now turns out that the analogous change in usb-storage
interacted badly with commit 09324d32d2 ("block: force an unlimited
segment size on queues with a virt boundary"), which was added later.
A typical error message is:
ehci-pci 0000:00:13.2: swiotlb buffer is full (sz: 327680 bytes),
total 32768 (slots), used 97 (slots)
There is no longer any reason to keep the virt_boundary_mask setting
in the uas driver. It was needed in the first place only for
handling devices with a block size smaller than the maxpacket size and
where the host controller was not capable of fully general
scatter-gather operation (that is, able to merge two SG segments into
a single USB packet). But:
High-speed or slower connections never use a bulk maxpacket
value larger than 512;
The SCSI layer does not handle block devices with a block size
smaller than 512 bytes;
All the host controllers capable of SuperSpeed operation can
handle fully general SG;
Since commit ea44d19076 ("usbip: Implement SG support to
vhci-hcd and stub driver") was merged, the USB/IP driver can
also handle SG.
Therefore all supported device/controller combinations should be okay
with no need for any special virt_boundary_mask. So in order to head
off potential problems similar to those affecting usb-storage, this
patch reverts commit 3ae62a4209.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: Oliver Neukum <oneukum@suse.com>
CC: <stable@vger.kernel.org>
Acked-by: Christoph Hellwig <hch@lst.de>
Fixes: 3ae62a4209 ("UAS: fix alignment of scatter/gather segments")
Link: https://lore.kernel.org/r/Pine.LNX.4.44L0.1910231132470.1878-100000@iolanthe.rowland.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 747668dbc0 ("usb-storage: Set virt_boundary_mask to avoid SG
overflows") attempted to solve a problem involving scatter-gather I/O
and USB/IP by setting the virt_boundary_mask for mass-storage devices.
However, it now turns out that this interacts badly with commit
09324d32d2 ("block: force an unlimited segment size on queues with a
virt boundary"), which was added later. A typical error message is:
ehci-pci 0000:00:13.2: swiotlb buffer is full (sz: 327680 bytes),
total 32768 (slots), used 97 (slots)
There is no longer any reason to keep the virt_boundary_mask setting
for usb-storage. It was needed in the first place only for handling
devices with a block size smaller than the maxpacket size and where
the host controller was not capable of fully general scatter-gather
operation (that is, able to merge two SG segments into a single USB
packet). But:
High-speed or slower connections never use a bulk maxpacket
value larger than 512;
The SCSI layer does not handle block devices with a block size
smaller than 512 bytes;
All the host controllers capable of SuperSpeed operation can
handle fully general SG;
Since commit ea44d19076 ("usbip: Implement SG support to
vhci-hcd and stub driver") was merged, the USB/IP driver can
also handle SG.
Therefore all supported device/controller combinations should be okay
with no need for any special virt_boundary_mask. So in order to fix
the swiotlb problem, this patch reverts commit 747668dbc0.
Reported-and-tested-by: Piergiorgio Sartor <piergiorgio.sartor@nexgo.de>
Link: https://marc.info/?l=linux-usb&m=157134199501202&w=2
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: Seth Bollinger <Seth.Bollinger@digi.com>
CC: <stable@vger.kernel.org>
Fixes: 747668dbc0 ("usb-storage: Set virt_boundary_mask to avoid SG overflows")
Acked-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/Pine.LNX.4.44L0.1910211145520.1673-100000@iolanthe.rowland.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
iso_buffer should be set to NULL after use and free in the while loop.
In the case of isochronous URB in the while loop, iso_buffer is
allocated and after sending it to server, buffer is deallocated. And
then, if the next URB in the while loop is not a isochronous pipe,
iso_buffer still holds the previously deallocated buffer address and
kfree tries to free wrong buffer address.
Fixes: ea44d19076 ("usbip: Implement SG support to vhci-hcd and stub driver")
Reported-by: kbuild test robot <lkp@intel.com>
Reported-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Suwan Kim <suwan.kim027@gmail.com>
Reviewed-by: Julia Lawall <julia.lawall@lip6.fr>
Acked-by: Shuah Khan <skhan@linuxfoundation.org>
Link: https://lore.kernel.org/r/20191022093017.8027-1-suwan.kim027@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It looks like some of the xhci debug code is passing u32 to functions
directly from __le32/__le64 fields.
Fix this by using le{32,64}_to_cpu() on these to fix the following
sparse warnings;
xhci-debugfs.c:205:62: warning: incorrect type in argument 1 (different base types)
xhci-debugfs.c:205:62: expected unsigned int [usertype] field0
xhci-debugfs.c:205:62: got restricted __le32
xhci-debugfs.c:206:62: warning: incorrect type in argument 2 (different base types)
xhci-debugfs.c:206:62: expected unsigned int [usertype] field1
xhci-debugfs.c:206:62: got restricted __le32
...
[Trim down commit message, sparse warnings were similar -Mathias]
Cc: <stable@vger.kernel.org> # 4.15+
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/1572013829-14044-4-git-send-email-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The arguments to queue_trb are always byteswapped to LE for placement in
the ring, but this should not happen in the case of immediate data; the
bytes copied out of transfer_buffer are already in the correct order.
Add a complementary byteswap so the bytes end up in the ring correctly.
This was observed on BE ppc64 with a "Texas Instruments TUSB73x0
SuperSpeed USB 3.0 xHCI Host Controller [104c:8241]" as a ch341
usb-serial adapter ("1a86:7523 QinHeng Electronics HL-340 USB-Serial
adapter") always transmitting the same character (generally NUL) over
the serial link regardless of the key pressed.
Cc: <stable@vger.kernel.org> # 5.2+
Fixes: 33e39350eb ("usb: xhci: add Immediate Data Transfer support")
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/1572013829-14044-3-git-send-email-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ef513be0a9 ("usb: xhci: Add Clear_TT_Buffer") schedules work
to clear TT buffer, but causes a use-after-free regression at the same time
Make sure hub_tt_work finishes before endpoint is disabled, otherwise
the work will dereference already freed endpoint and device related
pointers.
This was triggered when usb core failed to read the configuration
descriptor of a FS/LS device during enumeration.
xhci driver queued clear_tt_work while usb core freed and reallocated
a new device for the next enumeration attempt.
EHCI driver implents ehci_endpoint_disable() that makes sure
clear_tt_work has finished before it returns, but xhci lacks this support.
usb core will call hcd->driver->endpoint_disable() callback before
disabling endpoints, so we want this in xhci as well.
The added xhci_endpoint_disable() is based on ehci_endpoint_disable()
Fixes: ef513be0a9 ("usb: xhci: Add Clear_TT_Buffer")
Cc: <stable@vger.kernel.org> # v5.3
Reported-by: Johan Hovold <johan@kernel.org>
Suggested-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Johan Hovold <johan@kernel.org>
Tested-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/1572013829-14044-2-git-send-email-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A recent info-leak bug manifested itself along with warning about a
negative buffer overflow:
ldusb 1-1:0.28: Read buffer overflow, -131383859965943 bytes dropped
when it was really a rather large positive one.
A sanity check that prevents this has now been put in place, but let's
fix up the size format specifiers, which should all be unsigned.
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20191022143203.5260-3-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The custom ring-buffer implementation was merged without any locking or
explicit memory barriers, but a spinlock was later added by commit
9d33efd9a7 ("USB: ldusb bugfix").
The lock did not cover the update of the tail index once the entry had
been processed, something which could lead to memory corruption on
weakly ordered architectures or due to compiler optimisations.
Specifically, a completion handler running on another CPU might observe
the incremented tail index and update the entry before ld_usb_read() is
done with it.
Fixes: 2824bd250f ("[PATCH] USB: add ldusb driver")
Fixes: 9d33efd9a7 ("USB: ldusb bugfix")
Cc: stable <stable@vger.kernel.org> # 2.6.13
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20191022143203.5260-2-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Endpoints with a maxpacket length of 0 are probably useless. They
can't transfer any data, and it's not at all unlikely that an HCD will
crash or hang when trying to handle an URB for such an endpoint.
Currently the USB core does not check for endpoints having a maxpacket
value of 0. This patch adds a check, printing a warning and skipping
over any endpoints it catches.
Now, the USB spec does not rule out endpoints having maxpacket = 0.
But since they wouldn't have any practical use, there doesn't seem to
be any good reason for us to accept them.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/Pine.LNX.4.44L0.1910281050420.1485-100000@iolanthe.rowland.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The USB gadget core is supposed to manage pullups
of the controller. Don't manage pullups from within
the controller driver. Otherwise, function drivers
are not able to keep the controller disconnected from
the bus till they are ready. (e.g. g_webcam)
Reviewed-by: Pawel Laszczak <pawell@cadence.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
layerscape board sometimes reported some usb call trace, that is due to
kernel sent LPM tokerns automatically when it has no pending transfers
and think that the link is idle enough to enter L1, which procedure will
ask usb register has a recovery,then kernel will compare USBx_GFLADJ and
set GFLADJ_30MHZ, GFLADJ_30MHZ_REG until GFLADJ_30MHZ is equal 0x20, if
the conditions were met then issue occur, but whatever the conditions
whether were met that usb is all need keep GFLADJ_30MHZ of value is 0x20
(xhci spec ask use GFLADJ_30MHZ to adjust any offset from clock source
that generates the clock that drives the SOF counter, 0x20 is default
value of it)That is normal logic, so need remove the call trace.
Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
In dwc3_pci_probe a call to platform_device_alloc allocates a device
which is correctly put in case of error except one case: when the call to
platform_device_add_properties fails it directly returns instead of
going to error handling. This commit replaces return with the goto.
Fixes: 1a7b12f69a ("usb: dwc3: pci: Supply device properties via driver data")
Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
composite_dev_cleanup call from the failure of configfs_composite_bind
frees up the cdev->os_desc_req and cdev->req. If the previous calls of
bind and unbind is successful these will carry stale values.
Consider the below sequence of function calls:
configfs_composite_bind()
composite_dev_prepare()
- Allocate cdev->req, cdev->req->buf
composite_os_desc_req_prepare()
- Allocate cdev->os_desc_req, cdev->os_desc_req->buf
configfs_composite_unbind()
composite_dev_cleanup()
- free the cdev->os_desc_req->buf and cdev->req->buf
Next composition switch
configfs_composite_bind()
- If it fails goto err_comp_cleanup will call the
composite_dev_cleanup() function
composite_dev_cleanup()
- calls kfree up with the stale values of cdev->req->buf and
cdev->os_desc_req from the previous configfs_composite_bind
call. The free call on these stale values leads to double free.
Hence, Fix this issue by setting request and buffer pointer to NULL after
kfree.
Signed-off-by: Chandana Kishori Chiluveru <cchiluve@codeaurora.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Fix interrupt storm generated by endpoints when working in FIFO mode.
The TX_COMPLETE interrupt is used only by control endpoints processing.
Do not enable it for other types of endpoints.
Fixes: 914a3f3b37 ("USB: add atmel_usba_udc driver")
Signed-off-by: Cristian Birsan <cristian.birsan@microchip.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Fix the type of buf in __usbhsg_recip_send_status to
be __le16 to avoid the following sparse warning:
drivers/usb/renesas_usbhs/mod_gadget.c:335:14: warning: incorrect type in assignment (different base types)
drivers/usb/renesas_usbhs/mod_gadget.c:335:14: expected unsigned short
drivers/usb/renesas_usbhs/mod_gadget.c:335:14: got restricted __le16 [usertype]
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This patch fixes the following sparse warnings by shifting 8-bits after
le16_to_cpu().
drivers/usb/renesas_usbhs/mod_gadget.c:268:47: warning: restricted __le16 degrades to integer
drivers/usb/renesas_usbhs/mod_gadget.c:268:47: warning: cast to restricted __le16
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This patch fixes the following sparse warnings by using
a macro and a suitable variable type.
drivers/usb/gadget/udc/renesas_usb3.c:1547:17: warning: restricted __le16 degrades to integer
drivers/usb/gadget/udc/renesas_usb3.c:1550:43: warning: incorrect type in argument 2 (different base types)
drivers/usb/gadget/udc/renesas_usb3.c:1550:43: expected unsigned short [usertype] addr
drivers/usb/gadget/udc/renesas_usb3.c:1550:43: got restricted __le16 [usertype] wValue
drivers/usb/gadget/udc/renesas_usb3.c:1607:24: warning: incorrect type in assignment (different base types)
drivers/usb/gadget/udc/renesas_usb3.c:1607:24: expected unsigned short [assigned] [usertype] status
drivers/usb/gadget/udc/renesas_usb3.c:1607:24: got restricted __le16 [usertype]
drivers/usb/gadget/udc/renesas_usb3.c:1775:17: warning: restricted __le16 degrades to integer
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Fix the warnings generated by casting to/from __le16 without
using the correct functions.
Fixes the following sparse warnings:
drivers/usb/renesas_usbhs/common.c:165:25: warning: incorrect type in assignment (different base types)
drivers/usb/renesas_usbhs/common.c:165:25: expected restricted __le16 [usertype] wValue
drivers/usb/renesas_usbhs/common.c:165:25: got unsigned short
drivers/usb/renesas_usbhs/common.c:166:25: warning: incorrect type in assignment (different base types)
drivers/usb/renesas_usbhs/common.c:166:25: expected restricted __le16 [usertype] wIndex
drivers/usb/renesas_usbhs/common.c:166:25: got unsigned short
drivers/usb/renesas_usbhs/common.c:167:25: warning: incorrect type in assignment (different base types)
drivers/usb/renesas_usbhs/common.c:167:25: expected restricted __le16 [usertype] wLength
drivers/usb/renesas_usbhs/common.c:167:25: got unsigned short
drivers/usb/renesas_usbhs/common.c:173:39: warning: incorrect type in argument 3 (different base types)
drivers/usb/renesas_usbhs/common.c:173:39: expected unsigned short [usertype] data
drivers/usb/renesas_usbhs/common.c:173:39: got restricted __le16 [usertype] wValue
drivers/usb/renesas_usbhs/common.c:174:39: warning: incorrect type in argument 3 (different base types)
drivers/usb/renesas_usbhs/common.c:174:39: expected unsigned short [usertype] data
drivers/usb/renesas_usbhs/common.c:174:39: got restricted __le16 [usertype] wIndex
drivers/usb/renesas_usbhs/common.c:175:39: warning: incorrect type in argument 3 (different base types)
drivers/usb/renesas_usbhs/common.c:175:39: expected unsigned short [usertype] data
Note. I belive this to be correct, and should be a no-op on arm.
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The cdns3_host_init() function is declared in host-export.h
but host.c does not include it. Add the include to have
the declaration present (and remove the declaration of
cdns3_host_exit which is now static).
Fixes the following sparse warning:
drivers/usb/cdns3/host.c:58:5: warning: symbol 'cdns3_host_init' was not declared. Should it be static?
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The declarations of ssusb_gadget_{init,exit} are
in the mtu3_dr.h file but the code does that implements
them does not include this. Add the include to fix the
following sparse warnigns:
drivers/usb/mtu3/mtu3_core.c:825:5: warning: symbol 'ssusb_gadget_init' was not declared. Should it be static?
drivers/usb/mtu3/mtu3_core.c:925:6: warning: symbol 'ssusb_gadget_exit' was not declared. Should it be static?
Acked-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Check memory resource existence before releasing it to avoid NULL
pointer dereference
Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com>
Reviewed-by: Ran Wang <ran.wang_1@nxp.com>
Reviewed-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
After many randconfig builds, one configuration caused a link
error with dwc3-meson-g12a lacking the regmap-mmio code:
drivers/usb/dwc3/dwc3-meson-g12a.o: In function `dwc3_meson_g12a_probe':
dwc3-meson-g12a.c:(.text+0x9f): undefined reference to `__devm_regmap_init_mmio_clk'
Add the select statement that we have for all other users
of that dependency.
Fixes: c99993376f ("usb: dwc3: Add Amlogic G12A DWC3 glue")
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
USB_DR_MODE_UNKNOWN should be treated as error as it is done in
cdns3_drd_update_mode().
Fixes: 02ffc26df9 ("usb: cdns3: fix cdns3_core_init_role()")
Signed-off-by: Roger Quadros <rogerq@ti.com>
Link: https://lore.kernel.org/r/20191017075801.8734-1-rogerq@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix broken read implementation, which could be used to trigger slab info
leaks.
The driver failed to check if the custom ring buffer was still empty
when waking up after having waited for more data. This would happen on
every interrupt-in completion, even if no data had been added to the
ring buffer (e.g. on disconnect events).
Due to missing sanity checks and uninitialised (kmalloced) ring-buffer
entries, this meant that huge slab info leaks could easily be triggered.
Note that the empty-buffer check after wakeup is enough to fix the info
leak on disconnect, but let's clear the buffer on allocation and add a
sanity check to read() to prevent further leaks.
Fixes: 2824bd250f ("[PATCH] USB: add ldusb driver")
Cc: stable <stable@vger.kernel.org> # 2.6.13
Reported-by: syzbot+6fe95b826644f7f12b0b@syzkaller.appspotmail.com
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20191018151955.25135-2-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here's a fix for a long-standing locking bug in ti_usb_3410_5052 and
related clean up.
Both have been in linux-next with no reported issues.
Signed-off-by: Johan Hovold <johan@kernel.org>
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQQHbPq+cpGvN/peuzMLxc3C7H1lCAUCXancfAAKCRALxc3C7H1l
CNClAQCOgbL6NYZwy8xDBOHe5iPHJ218RfCHYwxiRpz3qA830QEA44yBBjPp44Z+
pi3yDRiNcS7epVN7mXGs+9GIrKPTdA8=
=8+KD
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-5.4-rc4' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus
Johan writes:
USB-serial fixes for 5.4-rc4
Here's a fix for a long-standing locking bug in ti_usb_3410_5052 and
related clean up.
Both have been in linux-next with no reported issues.
Signed-off-by: Johan Hovold <johan@kernel.org>
* tag 'usb-serial-5.4-rc4' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial:
USB: serial: ti_usb_3410_5052: clean up serial data access
USB: serial: ti_usb_3410_5052: fix port-close races
Use the tdev pointer directly instead of going through the port data
when accessing the serial data in close().
Signed-off-by: Johan Hovold <johan@kernel.org>
Fix races between closing a port and opening or closing another port on
the same device which could lead to a failure to start or stop the
shared interrupt URB. The latter could potentially cause a
use-after-free or worse in the completion handler on driver unbind.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
A recent commit addressing a runtime PM use-count regression, introduced
a use-after-free by not making sure we held a reference to the struct
usb_interface for the lifetime of the driver data.
Fixes: 9a31535859 ("USB: usblp: fix runtime PM after driver unbind")
Cc: stable <stable@vger.kernel.org>
Reported-by: syzbot+cd24df4d075c319ebfc5@syzkaller.appspotmail.com
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20191015175522.18490-1-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It seems that the right variable to use in this case is *i*, instead of
*n*, otherwise there is an undefined behavior when right shifiting by more
than 31 bits when multiplying n by 8; notice that *n* can take values
equal or greater than 4 (4, 8, 16, ...).
Also, notice that under the current conditions (bl = 3), we are skiping
the handling of bytes 3, 7, 31... So, fix this by updating this logic
and limit *bl* up to 4 instead of up to 3.
This fix is based on function udc_stuff_fifo().
Addresses-Coverity-ID: 1454834 ("Bad bit shift operation")
Fixes: 24a28e4283 ("USB: gadget driver for LPC32xx")
Cc: stable@vger.kernel.org
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Link: https://lore.kernel.org/r/20191014191830.GA10721@embeddedor
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Dequeuing implementation in cdns3_gadget_ep_dequeue gets first request from
deferred_req_list and changed TRB associated with it to LINK TRB.
This approach is incorrect because deferred_req_list contains requests
that have not been placed on hardware RING. In this case driver should
just giveback this request to gadget driver.
The patch implements new approach that first checks where dequeuing
request is located and only when it's on Transfer Ring then changes TRB
associated with it to LINK TRB.
During processing completed transfers such LINK TRB will be ignored.
Reported-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Fixes: 7733f6c32e ("usb: cdns3: Add Cadence USB3 DRD Driver")
Reviewed-by: Peter Chen <peter.chen@nxp.com>
Link: https://lore.kernel.org/r/1570958420-22196-1-git-send-email-pawell@cadence.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The problem is that sizeof() is unsigned long so negative error codes
are type promoted to high positive values and the condition becomes
false.
Fixes: 1d427be4a3 ("USB: legousbtower: fix slab info leak at probe")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20191011141115.GA4521@mwanda
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If disconnect() races with release() after a process has been
interrupted, release() could end up returning early and the driver would
fail to free its driver data.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20191010125835.27031-3-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If disconnect() races with release() after a process has been
interrupted, release() could end up returning early and the driver would
fail to free its driver data.
Fixes: 2824bd250f ("[PATCH] USB: add ldusb driver")
Cc: stable <stable@vger.kernel.org> # 2.6.13
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20191010125835.27031-2-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver was using its struct usb_interface pointer as an inverted
disconnected flag, but was setting it to NULL without making sure all
code paths that used it were done with it.
Before commit ef61eb43ad ("USB: yurex: Fix protection fault after
device removal") this included the interrupt-in completion handler, but
there are further accesses in dev_err and dev_dbg statements in
yurex_write() and the driver-data destructor (sic!).
Fix this by unconditionally stopping also the control URB at disconnect
and by using a dedicated disconnected flag.
Note that we need to take a reference to the struct usb_interface to
avoid a use-after-free in the destructor whenever the device was
disconnected while the character device was still open.
Fixes: aadd6472d9 ("USB: yurex.c: remove dbg() usage")
Fixes: 45714104b9 ("USB: yurex.c: remove err() usage")
Cc: stable <stable@vger.kernel.org> # 3.5: ef61eb43ad
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20191009153848.8664-6-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Weitao Wang