Sync code to the same with tk4 pub/lts/0017-kabi, except deleted rue
and wujing. Partners can submit pull requests to this branch, and we
can pick the commits to tk4 pub/lts/0017-kabi easly.
Signed-off-by: Jianping Liu <frankjpliu@tencent.com>
Gitee limit the repo's size to 3GB, to reduce the size of the code,
sync codes to ock 5.4.119-20.0009.21 in one commit.
Signed-off-by: Jianping Liu <frankjpliu@tencent.com>
Sync kernel codes to the same with 590eaf1fec ("Init Repo base on
linux 5.4.32 long term, and add base tlinux kernel interfaces."), which
is from tk4, and it is the base of tk4.
Signed-off-by: Jianping Liu <frankjpliu@tencent.com>
The branch contains driver changes that are tightly
connected to SoC specific code. Aside from smaller
cleanups and bug fixes, here is a list of the notable
changes.
New device drivers:
- The Turris Mox router has a new "moxtet" bus driver
for its on-board pluggable extension bus. The
same platform also gains a firmware driver.
- The Samsung Exynos family gains a new Chipid driver
exporting using the soc device sysfs interface
- A similar socinfo driver for Qualcomm Snapdragon
chips.
- A firmware driver for the NXP i.MX DSP IPC protocol
using shared memory and a mailbox
Other changes:
- The i.MX reset controller driver now supports the
NXP i.MX8MM chip
- Amlogic SoC specific drivers gain support for
the S905X3 and A311D chips
- A rework of the TI Davinci framebuffer driver to
allow important cleanups in the platform code
- A couple of device drivers for removed ARM SoC
platforms are removed. Most of the removals were
picked up by other maintainers, this contains
whatever was left.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=lxFi
-----END PGP SIGNATURE-----
Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC driver updates from Arnd Bergmann:
"This contains driver changes that are tightly connected to SoC
specific code. Aside from smaller cleanups and bug fixes, here is a
list of the notable changes.
New device drivers:
- The Turris Mox router has a new "moxtet" bus driver for its
on-board pluggable extension bus. The same platform also gains a
firmware driver.
- The Samsung Exynos family gains a new Chipid driver exporting using
the soc device sysfs interface
- A similar socinfo driver for Qualcomm Snapdragon chips.
- A firmware driver for the NXP i.MX DSP IPC protocol using shared
memory and a mailbox
Other changes:
- The i.MX reset controller driver now supports the NXP i.MX8MM chip
- Amlogic SoC specific drivers gain support for the S905X3 and A311D
chips
- A rework of the TI Davinci framebuffer driver to allow important
cleanups in the platform code
- A couple of device drivers for removed ARM SoC platforms are
removed. Most of the removals were picked up by other maintainers,
this contains whatever was left"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (123 commits)
bus: uniphier-system-bus: use devm_platform_ioremap_resource()
soc: ti: ti_sci_pm_domains: Add support for exclusive and shared access
dt-bindings: ti_sci_pm_domains: Add support for exclusive and shared access
firmware: ti_sci: Allow for device shared and exclusive requests
bus: imx-weim: remove incorrect __init annotations
fbdev: remove w90x900/nuc900 platform drivers
spi: remove w90x900 driver
net: remove w90p910-ether driver
net: remove ks8695 driver
firmware: turris-mox-rwtm: Add sysfs documentation
firmware: Add Turris Mox rWTM firmware driver
dt-bindings: firmware: Document cznic,turris-mox-rwtm binding
bus: moxtet: fix unsigned comparison to less than zero
bus: moxtet: remove set but not used variable 'dummy'
ARM: scoop: Use the right include
dt-bindings: power: add Amlogic Everything-Else power domains bindings
soc: amlogic: Add support for Everything-Else power domains controller
fbdev: da8xx: use resource management for dma
fbdev: da8xx-fb: drop a redundant if
fbdev: da8xx-fb: use devm_platform_ioremap_resource()
...
TISCI protocol supports for enabling the device either with exclusive
permissions for the requesting host or with sharing across the hosts.
There are certain devices which are exclusive to Linux context and
there are certain devices that are shared across different host contexts.
So add support for getting this information from DT by increasing
the power-domain cells to 2.
For keeping the DT backward compatibility intact, defaulting the
device permissions to set the exclusive flag set. In this case the
power-domain-cells is 1.
Reviewed-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fix sparse warnings:
drivers/soc/ti/pm33xx.c:144:27: warning: symbol 'rtc_wake_src' was not declared. Should it be static?
drivers/soc/ti/pm33xx.c:160:5: warning: symbol 'am33xx_rtc_only_idle' was not declared. Should it be static?
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The patch fixes a bunch of static checker warnings.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We continue to see a lot of new material. I've highlighted some of it
below, but there's been more beyond that as well.
One of the sweeping changes is that many boards have seen their ARM Mali
GPU devices added to device trees, since the DRM drivers have now been
merged.
So, with the caveat that I have surely missed several great
contributions, here's a collection of the material this time around:
New SoCs:
- Mediatek mt8183 (4x Cortex-A73 + 4x Cortex-A53)
- TI J721E (2x Cortex-A72 + 3x Cortex-R5F + 3 DSPs + MMA)
- Amlogic G12B (4x Cortex-A73 + 2x Cortex-A53)
New Boards / platforms:
- Aspeed BMC support for a number of new server platforms
- Kontron SMARC SoM (several i.MX6 versions)
- Novtech's Meerkat96 (i.MX7)
- ST Micro Avenger96 board
- Hardkernel ODROID-N2 (Amlogic G12B)
- Purism Librem5 devkit (i.MX8MQ)
- Google Cheza (Qualcomm SDM845)
- Qualcomm Dragonboard 845c (Qualcomm SDM845)
- Hugsun X99 TV Box (Rockchip RK3399)
- Khadas Edge/Edge-V/Captain (Rockchip RK3399)
Updated / expanded boards and platforms:
- Renesas r7s9210 has a lot of new peripherals added
- Polish and fixes for Rockchip-based Chromebooks
- Amlogic G12A has a lot of peripherals added
- Nvidia Jetson Nano sees various fixes and improvements, and is now at
feature parity with TX1
-----BEGIN PGP SIGNATURE-----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=sHZs
-----END PGP SIGNATURE-----
Merge tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM Devicetree updates from Olof Johansson:
"We continue to see a lot of new material. I've highlighted some of it
below, but there's been more beyond that as well.
One of the sweeping changes is that many boards have seen their ARM
Mali GPU devices added to device trees, since the DRM drivers have now
been merged.
So, with the caveat that I have surely missed several great
contributions, here's a collection of the material this time around:
New SoCs:
- Mediatek mt8183 (4x Cortex-A73 + 4x Cortex-A53)
- TI J721E (2x Cortex-A72 + 3x Cortex-R5F + 3 DSPs + MMA)
- Amlogic G12B (4x Cortex-A73 + 2x Cortex-A53)
New Boards / platforms:
- Aspeed BMC support for a number of new server platforms
- Kontron SMARC SoM (several i.MX6 versions)
- Novtech's Meerkat96 (i.MX7)
- ST Micro Avenger96 board
- Hardkernel ODROID-N2 (Amlogic G12B)
- Purism Librem5 devkit (i.MX8MQ)
- Google Cheza (Qualcomm SDM845)
- Qualcomm Dragonboard 845c (Qualcomm SDM845)
- Hugsun X99 TV Box (Rockchip RK3399)
- Khadas Edge/Edge-V/Captain (Rockchip RK3399)
Updated / expanded boards and platforms:
- Renesas r7s9210 has a lot of new peripherals added
- Fixes and polish for Rockchip-based Chromebooks
- Amlogic G12A has a lot of peripherals added
- Nvidia Jetson Nano sees various fixes and improvements, and is now
at feature parity with TX1"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (586 commits)
ARM: dts: gemini: Set DIR-685 SPI CS as active low
ARM: dts: exynos: Adjust buck[78] regulators to supported values on Arndale Octa
ARM: dts: exynos: Adjust buck[78] regulators to supported values on Odroid XU3 family
ARM: dts: exynos: Move Mali400 GPU node to "/soc"
ARM: dts: exynos: Fix imprecise abort on Mali GPU probe on Exynos4210
arm64: dts: qcom: qcs404: Add missing space for cooling-cells property
arm64: dts: rockchip: Fix USB3 Type-C on rk3399-sapphire
arm64: dts: rockchip: Update DWC3 modules on RK3399 SoCs
arm64: dts: rockchip: enable rk3328 watchdog clock
ARM: dts: rockchip: add display nodes for rk322x
ARM: dts: rockchip: fix vop iommu-cells on rk322x
arm64: dts: rockchip: Add support for Hugsun X99 TV Box
arm64: dts: rockchip: Define values for the IPA governor for rock960
arm64: dts: rockchip: Fix multiple thermal zones conflict in rk3399.dtsi
arm64: dts: rockchip: add core dtsi file for RK3399Pro SoCs
arm64: dts: rockchip: improve rk3328-roc-cc rgmii performance.
Revert "ARM: dts: rockchip: set PWM delay backlight settings for Minnie"
ARM: dts: rockchip: Configure BT_DEV_WAKE in on rk3288-veyron
arm64: dts: qcom: sdm845-cheza: add initial cheza dt
ARM: dts: msm8974-FP2: Add vibration motor
...
SoC platform changes. Main theme this merge window:
- The Netx platform (Netx 100/500) platform is removed by Linus Walleij--
the SoC doesn't have active maintainers with hardware, and in
discussions with the vendor the agreement was that it's OK to remove.
- Russell King has a series of patches that cleans up and refactors
SA1101 and RiscPC support.
-----BEGIN PGP SIGNATURE-----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=FX6e
-----END PGP SIGNATURE-----
Merge tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC platform updates from Olof Johansson:
"SoC platform changes. Main theme this merge window:
- The Netx platform (Netx 100/500) platform is removed by Linus
Walleij-- the SoC doesn't have active maintainers with hardware,
and in discussions with the vendor the agreement was that it's OK
to remove.
- Russell King has a series of patches that cleans up and refactors
SA1101 and RiscPC support"
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (47 commits)
ARM: stm32: use "depends on" instead of "if" after prompt
ARM: sa1100: convert to common clock framework
ARM: exynos: Cleanup cppcheck shifting warning
ARM: pxa/lubbock: remove lubbock_set_misc_wr() from global view
ARM: exynos: Only build MCPM support if used
arm: add missing include platform-data/atmel.h
ARM: davinci: Use GPIO lookup table for DA850 LEDs
ARM: OMAP2: drop explicit assembler architecture
ARM: use arch_extension directive instead of arch argument
ARM: imx: Switch imx7d to imx-cpufreq-dt for speed-grading
ARM: bcm: Enable PINCTRL for ARCH_BRCMSTB
ARM: bcm: Enable ARCH_HAS_RESET_CONTROLLER for ARCH_BRCMSTB
ARM: riscpc: enable chained scatterlist support
ARM: riscpc: reduce IRQ handling code
ARM: riscpc: move RiscPC assembly files from arch/arm/lib to mach-rpc
ARM: riscpc: parse video information from tagged list
ARM: riscpc: add ecard quirk for Atomwide 3port serial card
MAINTAINERS: mvebu: Add git entry
soc: ti: pm33xx: Add a print while entering RTC only mode with DDR in self-refresh
ARM: OMAP2+: Make some variables static
...
The irqchip driver depends on the SoC specific driver, but we want
to be able to compile-test it elsewhere:
WARNING: unmet direct dependencies detected for TI_SCI_INTA_MSI_DOMAIN
Depends on [n]: SOC_TI [=n]
Selected by [y]:
- TI_SCI_INTA_IRQCHIP [=y] && TI_SCI_PROTOCOL [=y]
drivers/irqchip/irq-ti-sci-inta.o: In function `ti_sci_inta_irq_domain_probe':
irq-ti-sci-inta.c:(.text+0x204): undefined reference to `ti_sci_inta_msi_create_irq_domain'
Rearrange the Kconfig and Makefile so we build the soc driver whenever
its users are there, regardless of the SOC_TI option.
Fixes: 49b323157b ("soc: ti: Add MSI domain bus support for Interrupt Aggregator")
Fixes: f011df6179 ("irqchip/ti-sci-inta: Add msi domain support")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Just two changes to make few platform data functions static, and to
call dev_info() if am437x is suspending to RTC-only mode. We want to
see this in case of issues as it depends on the board wiring for things
like DDR memory.
-----BEGIN PGP SIGNATURE-----
iQJFBAABCAAvFiEEkgNvrZJU/QSQYIcQG9Q+yVyrpXMFAl0AvH4RHHRvbnlAYXRv
bWlkZS5jb20ACgkQG9Q+yVyrpXOHcg/6AqtSmtYCOHCj1FgUlB0Ebf8lDg+M3n37
VxPapucpbF1tdE1FIGqNCBRiNiCzmCMF/0ARLpXN/GrBWe8PTplAOddlaf+9QU0R
IQyeUOOogYQ/NH388hUep+KPD3uSTA+N83rLiuyPdewBESIBOV82hoHVi40CsqWo
b0zhFBbrxX8rGJPSRXuKKy1rooxzYqRRrRKmDEzspvG4bmuHRnU0+UKa1GhNMlF5
YuDumzJ4sbznEZif6TB+bAzdqbKeAaTxs0yj411AvT5F1vsj50GLbUJzz2bC9wZ4
ihfbL8/+ODSvEZKWW2nrlsZp297GS2y4f3yCuDy48dYA/Ud3dL1nypa1wde44HbI
sANRz4ihXngRFoYJpTgs+bRrU16al1EPMeXCMmnMTBMPMnSCSd5Vix0jdCn+cQHq
sQC5sCBnG3A9Yk10vyWvD4/LZ7FVX29zXGUoZxoxICwxbJZvhMlCnZjCbQVCqfn7
dt99g3jxGcn2COg8mjMqR7zmCzTNn2TuWPbceyZYOC7/POeKOdlqi2xQN1at+RxE
wm5PLNZ1FkLw2FhrtmtiGbFPQEkXsbHRJo7iJpJYRqBsypvVfeY6y8k7r+w4GE8K
xWtXNh1oARIWLNVbq/P2UFq/KnzntX3M1UrPiB7sept3xmW0y6q2nu1LMLrhAvUM
Wk78ehVR518=
=+Fzf
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v5.3/soc-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into arm/soc
ti-sysc soc changes for v5.3
Just two changes to make few platform data functions static, and to
call dev_info() if am437x is suspending to RTC-only mode. We want to
see this in case of issues as it depends on the board wiring for things
like DDR memory.
* tag 'omap-for-v5.3/soc-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
soc: ti: pm33xx: Add a print while entering RTC only mode with DDR in self-refresh
ARM: OMAP2+: Make some variables static
Signed-off-by: Olof Johansson <olof@lixom.net>
Currently there is no way to distinguish if the SoC entered DS0
mode or the RTC only mode. Hence add a print before entering
the RTC only mode.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation this program is
distributed in the hope that it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 655 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070034.575739538@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add SPDX license identifiers to all Make/Kconfig files which:
- Have no license information of any form
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull IRQ chip updates from Ingo Molnar:
"A late irqchips update:
- New TI INTR/INTA set of drivers
- Rewrite of the stm32mp1-exti driver as a platform driver
- Update the IOMMU MSI mapping API to be RT friendly
- A number of cleanups and other low impact fixes"
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (34 commits)
iommu/dma-iommu: Remove iommu_dma_map_msi_msg()
irqchip/gic-v3-mbi: Don't map the MSI page in mbi_compose_m{b, s}i_msg()
irqchip/ls-scfg-msi: Don't map the MSI page in ls_scfg_msi_compose_msg()
irqchip/gic-v3-its: Don't map the MSI page in its_irq_compose_msi_msg()
irqchip/gicv2m: Don't map the MSI page in gicv2m_compose_msi_msg()
iommu/dma-iommu: Split iommu_dma_map_msi_msg() in two parts
genirq/msi: Add a new field in msi_desc to store an IOMMU cookie
arm64: arch_k3: Enable interrupt controller drivers
irqchip/ti-sci-inta: Add msi domain support
soc: ti: Add MSI domain bus support for Interrupt Aggregator
irqchip/ti-sci-inta: Add support for Interrupt Aggregator driver
dt-bindings: irqchip: Introduce TISCI Interrupt Aggregator bindings
irqchip/ti-sci-intr: Add support for Interrupt Router driver
dt-bindings: irqchip: Introduce TISCI Interrupt router bindings
gpio: thunderx: Use the default parent apis for {request,release}_resources
genirq: Introduce irq_chip_{request,release}_resource_parent() apis
firmware: ti_sci: Add helper apis to manage resources
firmware: ti_sci: Add RM mapping table for am654
firmware: ti_sci: Add support for IRQ management
firmware: ti_sci: Add support for RM core ops
...
With the system coprocessor managing the range allocation of the
inputs to Interrupt Aggregator, it is difficult to represent
the device IRQs from DT.
The suggestion is to use MSI in such cases where devices wants
to allocate and group interrupts dynamically.
Create a MSI domain bus layer that allocates and frees MSIs for
a device.
APIs that are implemented:
- ti_sci_inta_msi_create_irq_domain() that creates a MSI domain
- ti_sci_inta_msi_domain_alloc_irqs() that creates MSIs for the
specified device and resource.
- ti_sci_inta_msi_domain_free_irqs() frees the irqs attached to the device.
- ti_sci_inta_msi_get_virq() for getting the virq attached to a specific event.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
During RTC-only suspend, power is lost to the wkup domain, so we need to
save and restore the state of that domain. We also need to store some
information within the RTC registers so that u-boot can do the right thing
at powerup.
The state is entered by getting the RTC to bring the pmic_power_en line low
which will instruct the PMIC to disable the appropriate power rails after
putting DDR into self-refresh mode. To bring pmic_power_en low, we need to
get an ALARM2 event. Since we are running from SRAM at that point, it means
calculating what the next second is (via ASM) and programming that into the
RTC. This patch also adds support for wake up source detection.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Move the am33xx_push_sram_idle function to the top as a preparation
for rtc+ddr mode as the function will be called by multiple functions
currently present before it.
No functional changes.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Clang warns when one enumerated type is implicitly converted to another:
drivers/soc/ti/knav_dma.c:601:20: warning: implicit conversion from
enumeration type 'enum dma_data_direction' to different enumeration type
'enum dma_transfer_direction' [-Wenum-conversion]
chan->direction = DMA_NONE;
~ ^~~~~~~~
1 warning generated.
While DMA_NONE and DMA_TRANS_NONE have different values, there is no
functional change because direction is never checked against DMA_NONE,
only against DMA_MEM_TO_DEV and DMA_DEV_TO_MEM.
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
The Keystone QMSS driver is pretty damaged, in the sense that it
does things like this:
irq_set_affinity_hint(irq, to_cpumask(&cpu_map));
where cpu_map is a local variable. As we leave the function, this
will point to nowhere-land, and things will end-up badly.
Instead, let's use a proper cpumask that gets allocated, giving
the driver a chance to actually work with things like irqbalance
as well as have a hypothetical 64bit future.
Cc: stable@vger.kernel.org
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
The most noteworthy SoC driver changes this time include:
- The TEE subsystem gains an in-kernel interface to access the TEE
from device drivers.
- The reset controller subsystem gains a driver for the Qualcomm
Snapdragon 845 Power Domain Controller.
- The Xilinx Zynq platform now has a firmware interface for its
platform management unit. This contains a firmware "ioctl" interface
that was a little controversial at first, but the version we merged
solved that by not exposing arbitrary firmware calls to user space.
- The Amlogic Meson platform gains a "canvas" driver that is used
for video processing and shared between different high-level drivers.
The rest is more of the usual, mostly related to SoC specific power
management support and core drivers in drivers/soc:
- Several Renesas SoCs (RZ/G1N, RZ/G2M, R-Car V3M, RZ/A2M) gain new
features related to power and reset control.
- The Mediatek mt8183 and mt6765 SoC platforms gain support for
their respective power management chips.
- A new driver for NXP i.MX8, which need a firmware interface for
power management.
- The SCPI firmware interface now contains support estimating power
usage of performance states
- The NVIDIA Tegra "pmc" driver gains a few new features, in particular
a pinctrl interface for configuring the pads.
- Lots of small changes for Qualcomm, in particular the "smem"
device driver.
- Some cleanups for the TI OMAP series related to their sysc
controller.
Additional cleanups and bugfixes in SoC specific drivers include the
Meson, Keystone, NXP, AT91, Sunxi, Actions, and Tegra platforms.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=c/PQ
-----END PGP SIGNATURE-----
Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver updates from Arnd Bergmann:
"The most noteworthy SoC driver changes this time include:
- The TEE subsystem gains an in-kernel interface to access the TEE
from device drivers.
- The reset controller subsystem gains a driver for the Qualcomm
Snapdragon 845 Power Domain Controller.
- The Xilinx Zynq platform now has a firmware interface for its
platform management unit. This contains a firmware "ioctl"
interface that was a little controversial at first, but the version
we merged solved that by not exposing arbitrary firmware calls to
user space.
- The Amlogic Meson platform gains a "canvas" driver that is used for
video processing and shared between different high-level drivers.
The rest is more of the usual, mostly related to SoC specific power
management support and core drivers in drivers/soc:
- Several Renesas SoCs (RZ/G1N, RZ/G2M, R-Car V3M, RZ/A2M) gain new
features related to power and reset control.
- The Mediatek mt8183 and mt6765 SoC platforms gain support for their
respective power management chips.
- A new driver for NXP i.MX8, which need a firmware interface for
power management.
- The SCPI firmware interface now contains support estimating power
usage of performance states
- The NVIDIA Tegra "pmc" driver gains a few new features, in
particular a pinctrl interface for configuring the pads.
- Lots of small changes for Qualcomm, in particular the "smem" device
driver.
- Some cleanups for the TI OMAP series related to their sysc
controller.
Additional cleanups and bugfixes in SoC specific drivers include the
Meson, Keystone, NXP, AT91, Sunxi, Actions, and Tegra platforms"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (129 commits)
firmware: tegra: bpmp: Implement suspend/resume support
drivers: clk: Add ZynqMP clock driver
dt-bindings: clock: Add bindings for ZynqMP clock driver
firmware: xilinx: Add zynqmp IOCTL API for device control
Documentation: xilinx: Add documentation for eemi APIs
MAINTAINERS: imx: include drivers/firmware/imx path
firmware: imx: add misc svc support
firmware: imx: add SCU firmware driver support
reset: Fix potential use-after-free in __of_reset_control_get()
dt-bindings: arm: fsl: add scu binding doc
soc: fsl: qbman: add interrupt coalesce changing APIs
soc: fsl: bman_portals: defer probe after bman's probe
soc: fsl: qbman: Use last response to determine valid bit
soc: fsl: qbman: Add 64 bit DMA addressing requirement to QBMan
soc: fsl: qbman: replace CPU 0 with any online CPU in hotplug handlers
soc: fsl: qbman: Check if CPU is offline when initializing portals
reset: qcom: PDC Global (Power Domain Controller) reset controller
dt-bindings: reset: Add PDC Global binding for SDM845 SoCs
reset: Grammar s/more then once/more than once/
bus: ti-sysc: Just use SET_NOIRQ_SYSTEM_SLEEP_PM_OPS
...
In preparation to remove the node name pointer from struct device_node,
convert printf users to use the %pOFn format specifier.
Cc: Li Yang <leoyang.li@nxp.com>
Cc: David Brown <david.brown@linaro.org>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
Cc: Santosh Shilimkar <ssantosh@kernel.org>
Cc: linuxppc-dev@lists.ozlabs.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-soc@vger.kernel.org
Acked-by: Thierry Reding <treding@nvidia.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Qiang Zhao <qiang.zhao@nxp.com>
Acked-by: Andy Gross <andy.gross@linaro.org>
Signed-off-by: Rob Herring <robh@kernel.org>
Trivial fix to spelling mistake in dev_err messages and comments
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Business as usual -- the bulk of our changes are to devicetree files
with new hardware support, new SoCs and platforms, and new board types.
New SoCs/platforms:
- Raspberry Pi Compute Module (CM1) and IO board
- i.MX6SSL from NXP
- Renesas RZ/N1D SoC (R9A06G032), Dual Cortex-A7 with Ethernet, CAN and
PLC interfaces
- TI AM654 SoC, Quad Cortex-A53, safety subsystem with Cortex-R5
controllers, communication and PRU subsystem and lots of other
interfaces (PCIe, USB3, etc).
New boards and systems:
- Several Atmel at91-based boards from Laird
- Marvell Armada388-based Helios4 board from SolidRun
- Samsung Aires-based phones (s5pv210)
- Allwinner A64-based Pinebook laptop
In addition to the above, there's the usual amount of new devices
described on existing platforms, fixes and tweaks and new minor variants
of boards/platforms.
-----BEGIN PGP SIGNATURE-----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=J0qC
-----END PGP SIGNATURE-----
Merge tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM device-tree updates from Olof Johansson:
"Business as usual -- the bulk of our changes are to devicetree files
with new hardware support, new SoCs and platforms, and new board
types.
New SoCs/platforms:
- Raspberry Pi Compute Module (CM1) and IO board
- i.MX6SSL from NXP
- Renesas RZ/N1D SoC (R9A06G032), Dual Cortex-A7 with Ethernet, CAN
and PLC interfaces
- TI AM654 SoC, Quad Cortex-A53, safety subsystem with Cortex-R5
controllers, communication and PRU subsystem and lots of other
interfaces (PCIe, USB3, etc).
New boards and systems:
- Several Atmel at91-based boards from Laird
- Marvell Armada388-based Helios4 board from SolidRun
- Samsung Aires-based phones (s5pv210)
- Allwinner A64-based Pinebook laptop
In addition to the above, there's the usual amount of new devices
described on existing platforms, fixes and tweaks and new minor
variants of boards/platforms"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (478 commits)
arm64: dts: sdm845: Add tsens nodes
arm64: dts: msm8996: thermal: Initialise via DT and add second controller
arm64: dts: sprd: Add one suspend timer
arm64: dts: sprd: Add SC27XX ADC device
arm64: dts: sprd: Add SC27XX eFuse device
arm64: dts: sprd: Add SC27XX vibrator device
arm64: dts: sprd: Add SC27XX breathing light controller device
arm64: dts: meson-axg: add spdif-dit codec
arm64: dts: meson-axg: add lineout codec
arm64: dts: meson-axg: add linein codec
arm64: dts: meson-axg: add tdm interfaces
arm64: dts: meson-axg: add tdmout formatters
arm64: dts: meson-axg: add tdmin formatters
arm64: dts: meson-axg: add spdifout
arm64: dts: rockchip: add led support for Firefly-RK3399
arm64: dts: rockchip: remove deprecated Type-C PHY properties on rk3399
arm64: dts: rockchip: add power button support for Firefly-RK3399
ARM: dts: aspeed: Add coprocessor interrupt controller
arm64: dts: meson-axg: add audio arb reset controller
arm64: dts: meson-axg: add usb power regulator
...
Some of the larger changes this merge window:
- Removal of drivers for Exynos5440, a Samsung SoC that never saw
widespread use.
- Uniphier support for USB3 and SPI reset handling
- Syste control and SRAM drivers and bindings for Allwinner platforms
- Qualcomm AOSS (Always-on subsystem) reset controller drivers
- Raspberry Pi hwmon driver for voltage
- Mediatek pwrap (pmic) support for MT6797 SoC
-----BEGIN PGP SIGNATURE-----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=ZjwY
-----END PGP SIGNATURE-----
Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver updates from Olof Johansson:
"Some of the larger changes this merge window:
- Removal of drivers for Exynos5440, a Samsung SoC that never saw
widespread use.
- Uniphier support for USB3 and SPI reset handling
- Syste control and SRAM drivers and bindings for Allwinner platforms
- Qualcomm AOSS (Always-on subsystem) reset controller drivers
- Raspberry Pi hwmon driver for voltage
- Mediatek pwrap (pmic) support for MT6797 SoC"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (52 commits)
drivers/firmware: psci_checker: stash and use topology_core_cpumask for hotplug tests
soc: fsl: cleanup Kconfig menu
soc: fsl: dpio: Convert DPIO documentation to .rst
staging: fsl-mc: Remove remaining files
staging: fsl-mc: Move DPIO from staging to drivers/soc/fsl
staging: fsl-dpaa2: eth: move generic FD defines to DPIO
soc: fsl: qe: gpio: Add qe_gpio_set_multiple
usb: host: exynos: Remove support for Exynos5440
clk: samsung: Remove support for Exynos5440
soc: sunxi: Add the A13, A23 and H3 system control compatibles
reset: uniphier: add reset control support for SPI
cpufreq: exynos: Remove support for Exynos5440
ata: ahci-platform: Remove support for Exynos5440
soc: imx6qp: Use GENPD_FLAG_ALWAYS_ON for PU errata
soc: mediatek: pwrap: add mt6351 driver for mt6797 SoCs
soc: mediatek: pwrap: add pwrap driver for mt6797 SoCs
soc: mediatek: pwrap: fix cipher init setting error
dt-bindings: pwrap: mediatek: add pwrap support for MT6797
reset: uniphier: add USB3 core reset control
dt-bindings: reset: uniphier: add USB3 core reset support
...
Add option to build AM6 SoC specific components
Reviewed-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Benjamin Fair <b-fair@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add support for RTC mode to low level suspend code. This includes
providing the rtc base address for the assembly code to configuring the
PMIC_PWR_EN line late in suspend to enter RTC+DDR mode.
Note: This patch also fold in left out space parameter for
am33xx_emif_sram_table and am43xx_emif_sram_table
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add an argument to the sleep33xx and sleep43xx code to allow us to set
flags to determine which portions of the code get called in order to use
the same code for multiple power saving modes. This patch allows us to
decide whether or not we flush and disable caches, save EMIF context,
put the memory into self refresh and disable the EMIF, and/or invoke
the wkup_m3 when entering into WFI.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Everyone gets these #ifdefs wrong, leading to another warning here:
drivers/soc/ti/wkup_m3_ipc.c:547:12: error: 'wkup_m3_ipc_resume' defined but not used [-Werror=unused-function]
static int wkup_m3_ipc_resume(struct device *dev)
drivers/soc/ti/wkup_m3_ipc.c:539:12: error: 'wkup_m3_ipc_suspend' defined but not used [-Werror=unused-function]
static int wkup_m3_ipc_suspend(struct device *dev)
The easiest way to get it right is to remove all the #ifdefs and
let the compiler drop the unused functions silently after we
mark them as __maybe_unused.
Fixes: 7a872b6fb7 ("soc: ti: wkup_m3_ipc: Add rtc_only with ddr in self refresh mode support")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Add wkup_m3_request_wake_src to allow users to get the name of
the wakeup source after a DeepSleep or Standby transition.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Adds rtc_only support. This needs resume function to shutdown and
reboot the m3.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
- Additional struct_size() conversions (Matthew, Kees)
- Explicitly reported overflow fixes (Silvio, Kees)
- Add missing kvcalloc() function (Kees)
- Treewide conversions of allocators to use either 2-factor argument
variant when available, or array_size() and array3_size() as needed (Kees)
-----BEGIN PGP SIGNATURE-----
Comment: Kees Cook <kees@outflux.net>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=zUUp
-----END PGP SIGNATURE-----
Merge tag 'overflow-v4.18-rc1-part2' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux
Pull more overflow updates from Kees Cook:
"The rest of the overflow changes for v4.18-rc1.
This includes the explicit overflow fixes from Silvio, further
struct_size() conversions from Matthew, and a bug fix from Dan.
But the bulk of it is the treewide conversions to use either the
2-factor argument allocators (e.g. kmalloc(a * b, ...) into
kmalloc_array(a, b, ...) or the array_size() macros (e.g. vmalloc(a *
b) into vmalloc(array_size(a, b)).
Coccinelle was fighting me on several fronts, so I've done a bunch of
manual whitespace updates in the patches as well.
Summary:
- Error path bug fix for overflow tests (Dan)
- Additional struct_size() conversions (Matthew, Kees)
- Explicitly reported overflow fixes (Silvio, Kees)
- Add missing kvcalloc() function (Kees)
- Treewide conversions of allocators to use either 2-factor argument
variant when available, or array_size() and array3_size() as needed
(Kees)"
* tag 'overflow-v4.18-rc1-part2' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux: (26 commits)
treewide: Use array_size in f2fs_kvzalloc()
treewide: Use array_size() in f2fs_kzalloc()
treewide: Use array_size() in f2fs_kmalloc()
treewide: Use array_size() in sock_kmalloc()
treewide: Use array_size() in kvzalloc_node()
treewide: Use array_size() in vzalloc_node()
treewide: Use array_size() in vzalloc()
treewide: Use array_size() in vmalloc()
treewide: devm_kzalloc() -> devm_kcalloc()
treewide: devm_kmalloc() -> devm_kmalloc_array()
treewide: kvzalloc() -> kvcalloc()
treewide: kvmalloc() -> kvmalloc_array()
treewide: kzalloc_node() -> kcalloc_node()
treewide: kzalloc() -> kcalloc()
treewide: kmalloc() -> kmalloc_array()
mm: Introduce kvcalloc()
video: uvesafb: Fix integer overflow in allocation
UBIFS: Fix potential integer overflow in allocation
leds: Use struct_size() in allocation
Convert intel uncore to struct_size
...
This branch contains platform-related driver updates for ARM and ARM64.
Highlights:
- ARM SCMI (System Control & Management Interface) driver cleanups
- Hisilicon support for LPC bus w/ ACPI
- Reset driver updates for several platforms: Uniphier,
- Rockchip power domain bindings and hardware descriptions for several SoCs.
- Tegra memory controller reset improvements
-----BEGIN PGP SIGNATURE-----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=xs+f
-----END PGP SIGNATURE-----
Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver updates from Olof Johansson:
"This contains platform-related driver updates for ARM and ARM64.
Highlights:
- ARM SCMI (System Control & Management Interface) driver cleanups
- Hisilicon support for LPC bus w/ ACPI
- Reset driver updates for several platforms: Uniphier,
- Rockchip power domain bindings and hardware descriptions for
several SoCs.
- Tegra memory controller reset improvements"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (59 commits)
ARM: tegra: fix compile-testing PCI host driver
soc: rockchip: power-domain: add power domain support for px30
dt-bindings: power: add binding for px30 power domains
dt-bindings: power: add PX30 SoCs header for power-domain
soc: rockchip: power-domain: add power domain support for rk3228
dt-bindings: power: add binding for rk3228 power domains
dt-bindings: power: add RK3228 SoCs header for power-domain
soc: rockchip: power-domain: add power domain support for rk3128
dt-bindings: power: add binding for rk3128 power domains
dt-bindings: power: add RK3128 SoCs header for power-domain
soc: rockchip: power-domain: add power domain support for rk3036
dt-bindings: power: add binding for rk3036 power domains
dt-bindings: power: add RK3036 SoCs header for power-domain
dt-bindings: memory: tegra: Remove Tegra114 SATA and AFI reset definitions
memory: tegra: Remove Tegra114 SATA and AFI reset definitions
memory: tegra: Register SMMU after MC driver became ready
soc: mediatek: remove unneeded semicolon
soc: mediatek: add a fixed wait for SRAM stable
soc: mediatek: introduce a CAPS flag for scp_domain_data
soc: mediatek: reuse regmap_read_poll_timeout helpers
...
Hwqueue has collect statistics in heavy use queue_pop/queu_push functions
for cache efficiency and make push/pop faster use percpu variables.
For performance reasons, driver should keep descriptor in software handler
as short as possible and quickly return it back to hardware queue.
Descriptors coming into driver from hardware after pop and return back
by push to reduce descriptor lifetime in driver collect statistics on percpu.
Signed-off-by: Vasyl Gomonovych <gomonovych@gmail.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
This patch provide APIs to allow client drivers to support
probe deferral. On K2G SoC, devices can be probed only
after the ti_sci_pm_domains driver is probed and ready.
As drivers may get probed at different order, any driver
that depends on knav dma and qmss drivers, for example
netcp network driver, needs to defer probe until
knav devices are probed and ready to service. To do this,
add an API to query the device ready status from the knav
dma and qmss devices.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Navigator Subsystem (NAVSS) available on K2G SoC has a cut down
version of QMSS with less number of queues, internal linking ram
with lesser number of buffers etc. It doesn't have status and
explicit push register space as in QMSS available on other K2 SoCs.
So define reg indices specific to QMSS on K2G. This patch introduces
"ti,66ak2g-navss-qm" compatibility to identify QMSS on K2G NAVSS
and to customize the dts handling code. Per Device manual,
descriptors with index less than or equal to regions0_size is in region 0
in the case of K2 QMSS where as for QMSS on K2G, descriptors with index
less than regions0_size is in region 0. So update the size accordingly in
the regions0_size bits of the linking ram size 0 register.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: WingMan Kwok <w-kwok2@ti.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
AM335x and AM437x support various low power modes as documented
in section 8.1.4.3 of the AM335x Technical Reference Manual and
section 6.4.3 of the AM437x Technical Reference Manual.
DeepSleep0 mode offers the lowest power mode with limited
wakeup sources without a system reboot and is mapped as
the suspend state in the kernel. In this state, MPU and
PER domains are turned off with the internal RAM held in
retention to facilitate the resume process. As part of
the boot process, the assembly code is copied over to OCMCRAM
so it can be executed to turn of the EMIF and put DDR into self
refresh.
Both platforms have a Cortex-M3 (WKUP_M3) which assists the MPU
in DeepSleep0 entry and exit. WKUP_M3 takes care
of the clockdomain and powerdomain transitions based on the
intended low power state. MPU needs to load the appropriate
WKUP_M3 binary onto the WKUP_M3 memory space before it can
leverage any of the PM features like DeepSleep. This loading
is handled by the remoteproc driver wkup_m3_rproc.
Communication with the WKUP_M3 is handled by a wkup_m3_ipc
driver that exposes the specific PM functionality to be used
the PM code.
In the current implementation when the suspend process
is initiated, MPU interrupts the WKUP_M3 to let it know about
the intent of entering DeepSleep0 and waits for an ACK. When
the ACK is received MPU continues with its suspend process
to suspend all the drivers and then jumps to assembly in
OCMC RAM. The assembly code puts the external RAM in self-refresh
mode, gates the MPU clock, and then finally executes the WFI
instruction. Execution of the WFI instruction with MPU clock gated
triggers another interrupt to the WKUP_M3 which then continues
with the power down sequence wherein the clockdomain and
powerdomain transition takes place. As part of the sleep sequence,
WKUP_M3 unmasks the interrupt lines for the wakeup sources. WFI
execution on WKUP_M3 causes the hardware to disable the main
oscillator of the SoC and from here system remains in sleep state
until a wake source brings the system into resume path.
When a wakeup event occurs, WKUP_M3 starts the power-up
sequence by switching on the power domains and finally
enabling the clock to MPU. Since the MPU gets powered down
as part of the sleep sequence in the resume path ROM code
starts executing. The ROM code detects a wakeup from sleep
and then jumps to the resume location in OCMC which was
populated in one of the IPC registers as part of the suspend
sequence.
Code is based on work by Vaibhav Bedia.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
If source string longer than max, kstrndup will alloc max+1 space.
So, we should make sure the result will not over limit.
Signed-off-by: Ma Shimiao <mashimiao.fnst@cn.fujitsu.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
knav_pool_create is an exported function. In the event of a call
before knav_queue_probe, we encounter a NULL pointer dereference
in the following line. Hence return -EPROBE_DEFER to the caller till
the kdev pointer is non-NULL.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Commit b6a1d093f9 ("PM / Domains: Extend generic power domain
debugfs") now creates a debugfs directory for each genpd based on the
name of the genpd. Currently no name is given to the genpd created by
ti_sci_pm_domains driver so because of this we see a NULL pointer
dereferences when it is accessed on boot when the debugfs entry creation
is attempted.
Give the genpd a name before registering it to avoid this.
Fixes: 52835d59fc ("soc: ti: Add ti_sci_pm_domains driver")
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Santosh Shilimkar <ssantosh@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fix error path while dma open channel issue. Also, no need to check output
on NULL if it's never returned.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce a ti_sci_pm_domains driver to act as a generic pm domain
provider to allow each device to attach and associate it's ti-sci-id so
that it can be controlled through the TI SCI protocol.
This driver implements a simple genpd where each device node has a
phandle to the power domain node and also must provide an index which
represents the ID to be passed with TI SCI representing the device using
a single phandle cell. The driver manually parses the phandle to get the
cell value. Through this interface the genpd dev_ops start and stop
hooks will use TI SCI to turn on and off each device as determined by
pm_runtime usage.
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Santosh Shilimkar <ssantosh@kernel.org>
Driver updates for ARM SoCs.
A handful of driver changes this time around. The larger changes are:
- Reset drivers for hi3660 and zx2967
- AHCI driver for Davinci, acked by Tejun and brought in here due to
platform dependencies
- Cleanups of atmel-ebi (External Bus Interface)
- Tweaks for Rockchip GRF (General Register File) usage (kitchensink misc
register range on the SoCs)
- PM domains changes for support of two new ZTE SoCs (zx296718 and zx2967)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=od7u
-----END PGP SIGNATURE-----
Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver updates from Arnd Bergmann:
"Driver updates for ARM SoCs.
A handful of driver changes this time around. The larger changes are:
- Reset drivers for hi3660 and zx2967
- AHCI driver for Davinci, acked by Tejun and brought in here due to
platform dependencies
- Cleanups of atmel-ebi (External Bus Interface)
- Tweaks for Rockchip GRF (General Register File) usage (kitchensink
misc register range on the SoCs)
- PM domains changes for support of two new ZTE SoCs (zx296718 and
zx2967)"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (53 commits)
soc: samsung: pmu: Add register defines for pad retention control
reset: make zx2967 explicitly non-modular
reset: core: fix reset_control_put
soc: samsung: pm_domains: Read domain name from the new label property
soc: samsung: pm_domains: Remove message about failed memory allocation
soc: samsung: pm_domains: Remove unused name field
soc: samsung: pm_domains: Use full names in subdomains registration log
sata: ahci-da850: un-hardcode the MPY bits
sata: ahci-da850: add a workaround for controller instability
sata: ahci: export ahci_do_hardreset() locally
sata: ahci-da850: implement a workaround for the softreset quirk
sata: ahci-da850: add device tree match table
sata: ahci-da850: get the sata clock using a connection id
soc: samsung: pmu: Remove duplicated define for ARM_L2_OPTION register
memory: atmel-ebi: Enable the SMC clock if specified
soc: samsung: pmu: Remove unused and duplicated defines
memory: atmel-ebi: Properly handle multiple reference to the same CS
memory: atmel-ebi: Fix the test to enable generic SMC logic
soc: samsung: pm_domains: Add new Exynos5433 compatible
soc: samsung: pmu: Add dummy support for Exynos5433 SoC
...
We don't currently have anything else for drivers/soc to
merge, but I'd expect that to change as soon as we can start
moving PM code into drivers with the recently posted SRAM
changes. Anyways, sent as a separate pull request to make
it easy to group the ARM SoC pull requests.
-----BEGIN PGP SIGNATURE-----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=2tPW
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.11/drivers-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/drivers
Just a single wkup_m3_ipc clean-up for v4.11 merge window.
We don't currently have anything else for drivers/soc to
merge, but I'd expect that to change as soon as we can start
moving PM code into drivers with the recently posted SRAM
changes. Anyways, sent as a separate pull request to make
it easy to group the ARM SoC pull requests.
* tag 'omap-for-v4.11/drivers-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
soc: ti: wkup_m3_ipc: Drop wait from wkup_m3_rproc_boot_thread
Signed-off-by: Olof Johansson <olof@lixom.net>
Jianping Liu