These should go together with the rest of the T10 protection information
defintions.
[mkp: s/T10_DIF/T10_PI/]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Bart Van Assche <bart.vanassche@sandisk.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
And remove the declaration of the latter in sd.h as scsi_debug was the
only user.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Bart Van Assche <bart.vanassche@sandisk.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In this post: http://www.spinics.net/lists/linux-scsi/msg97124.html the
author shows some kernel infrastructure complaining about a sleep in an
invalid context. Remove offending call to vmalloc(). Instead of using
kzalloc() which reviewers didn't like, use a bucket system (64 bytes on
the stack) and potentially multiple calls to sg_pcopy_from_buffer() to
construct the 'data-in' buffer for the SCSI REPORT LUNS command.
Signed-off-by: Douglas Gilbert <dgilbert@interlog.com>
Acked-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Bart Van Assche <bart.vanassche@sandisk.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
For reported SAS addresses replace fake IEEE registered NAAs (5) with
locally assigned NAAs (3).
Signed-off-by: Douglas Gilbert <dgilbert@interlog.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Bart Van Assche <bart.vanassche@sandisk.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Permit changing of a LU name from a (fake) IEEE registered NAA (5) to a
locally assigned UUID. Using a UUID (RFC 4122) for a SCSI designation
descriptor (e.g. a LU name) was added in spc5r08.pdf (a draft INCITS
standard) on 25 January 2016. Add parameter uuid_ctl to use a separate
UUID for each LU (storage device) name. Additional option for all LU
names to have the same UUID (since their storage is shared). Previous
action of using NAA identifier for LU name remains the default.
Signed-off-by: Douglas Gilbert <dgilbert@interlog.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Bart Van Assche <bart.vanassche@sandisk.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Cleanup some mode and vpd pages. Stop reporting SBC (disk) pages when
peripheral type is something else (e.g. tape). Update version
descriptors. Expand LBPRZ flag handling.
Signed-off-by: Douglas Gilbert <dgilbert@interlog.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Bart Van Assche <bart.vanassche@sandisk.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add submit_queue parameter (minimum and default: 1; maximum: nr_cpu_ids)
that controls how many queues are built, each with their own lock and
in_use bit vector. Add statistics parameter which is default off.
Signed-off-by: Douglas Gilbert <dgilbert@interlog.com>
Reviewed-by: Bart Van Assche <bart.vanassche@sandisk.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Based on "[PATH V2] scsi_debug: rework resp_report_luns" patch
sent by Tomas Winkler on Thursday, 26 Feb 2015. His notes:
1. Remove duplicated boundary checks which simplify the fill-in
loop
2. Use more of scsi generic API
Replace fixed length response array a with heap allocation
allowing up to 256 normal LUNs per target.
Signed-off-by: Douglas Gilbert <dgilbert@interlog.com>
Reviewed-by: Hannes Reinicke <hare@suse.de>
Reviewed-by: Tomas Winkler <tomas.winkler@intel.com>
Reviewed-by: Bart Van Assche <bart.vanassche@sandisk.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Use TYPE_* constants for SCSI peripheral device types instead of
numbers. Further cleanups requested by checkpatch.pl.
Signed-off-by: Douglas Gilbert <dgilbert@interlog.com>
Reviewed-by: Hannes Reinicke <hare@suse.de>
Reviewed-by: Bart Van Assche <bart.vanassche@sandisk.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The most common commands in normal use are the READ and WRITE SCSI
commands. Use likely and unlikely hints along the path taken by these
commands. Rename check_readiness() to make_ua() and remove associated
dead code. Rename devInfoReg() to find_build_dev_info().
Signed-off-by: Douglas Gilbert <dgilbert@interlog.com>
Reviewed-by: Hannes Reinicke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Group most defines together first; followed by struct definitions and
then table and variable definitions. Normalize all function headers.
[mkp: Corrected hex value in WP/DPOFUA MODE SENSE comment]
Signed-off-by: Douglas Gilbert <dgilbert@interlog.com>
Reviewed-by: Hannes Reinicke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When a negative value was placed in the delay parameter, a tasklet was
scheduled. Change the tasklet to a work queue. Previously a delay of -1
scheduled a high priority tasklet; since there are no high priority work
queues, treat -1 like other negative values in delay and schedule a work
item.
Signed-off-by: Douglas Gilbert <dgilbert@interlog.com>
Reviewed-by: Hannes Reinicke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add 'j' to delay names to make it clearer that its unit is jiffies and
to differentiate it from sdebug_ndelay whose unit is nanoseconds.
Signed-off-by: Douglas Gilbert <dgilbert@interlog.com>
Reviewed-by: Hannes Reinicke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The driver supports two command delay interfaces, the original one whose
unit is a jiffy, and a newer one whose unit is a nanosecond. Each had
different implementations. Keep both interfaces but simplify the
implemenation to use a single delay mechanism based on high resolution
timers.
Signed-off-by: Douglas Gilbert <dgilbert@interlog.com>
Reviewed-by: Hannes Reinicke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Remove logic to optionally hold host_lock while each command is
queued. Keep module and sysfs host_lock parameters for backward
compatibility. Note in module parameter description that host_lock is
ignored.
Signed-off-by: Douglas Gilbert <dgilbert@interlog.com>
Reviewed-by: Hannes Reinicke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Shorten file scope static and constant names. Use more
get/put_unaligned calls to hide bit banging. Introduce
sdebug_verbose boolean to replace frequent masking of
option bit flags. Add GPL and bump version.
[mkp: Use logical instead of bitwise OR for LBP VPD flags]
Signed-off-by: Douglas Gilbert <dgilbert@interlog.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Rename SCSI_MAX_SG_SEGMENTS to SG_CHUNK_SIZE, which means the amount
we fit into a single scatterlist chunk.
Rename SCSI_MAX_SG_CHAIN_SEGMENTS to SG_MAX_SEGMENTS.
Will move these 2 generic definitions to scatterlist.h later.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Acked-by: Bart Van Assche <bart.vanassche@sandisk.com> (for ib_srp changes)
Signed-off-by: Ming Lin <ming.l@ssi.samsung.com>
Acked-by: Tejun Heo <tj@kernel.org>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The OPTIMAL TRANSFER LENGTH reported by scsi_debug is 64 blocks which
translates to 32KB with the default logical block size. That's much
lower than what real storage devices typically report (256KB to 1MB).
Bump the optimal transfer length to 1024 blocks.
Acked-by: Douglas Gilbert <dgilbert@interlog.com>
Reviewed-by: Ewan Milne <emilne@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Even for signed types we have to check for bigger positive value first.
Otherwise it will be never happened.
Signed-off-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Douglas Gilbert <dgilbert@interlog.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Ewan Milne <emilne@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
do_div is the wrong way to divide a sector_t, as it is less efficient
when sector_t is 32-bit wide. With the upcoming do_div optimizations,
the kernel starts warning about this:
drivers/scsi/scsi_debug.c: In function 'dif_store':
include/asm-generic/div64.h:207:28: warning: comparison of distinct pointer types lacks a cast
This changes the code to use sector_div instead, which always produces
optimal code.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Hannes Reinicke <hare@suse.de>
Reviewed-by: Sagi Grimberg <sagig@mellanox.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Ruediger Meier observed a regression with the PREVENT ALLOW MEDIUM
REMOVAL command in lk 3.19:
http://www.spinics.net/lists/util-linux-ng/msg11448.html
Inspection indicated the same regression with VERIFY(10).
The patch is against lk 3.19.3 and also works with lk 4.3.0 . With this
patch both commands are accepted and do nothing.
ChangeLog:
- fix the lk 3.19 regression so that the PREVENT ALLOW MEDIUM REMOVAL
command is supported once again
- same fix for VERIFY(10)
Signed-off-by: Douglas Gilbert <dgilbert@interlog.com>
Reviewed-by: Hannes Reinicke <hare@suse.de>
Reviewed-by: Ewan Milne <emilne@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fixes the following warning
In function ‘resp_requests’:
drivers/scsi//scsi_debug.c:1432:15: warning: variable ‘want_dsense’ set
but not used [-Wunused-but-set-variable]
bool dsense, want_dsense;
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
The use case to report 'REPORT LUNS WLUN' described
in scsi_debug documentation didn't work because:
scsi_scan_host_selected() checks for:
lun < shost->max_lun
To fix this we set:
max_lun = SCSI_W_LUN_REPORT_LUNS + 1;
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Acked-by: Douglas Gilbert <dgilbert@interlog.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
The function should never be called with cmnd NULL so
put a fat WARN there.
Fix also smatch wraning:
schedule_resp() warn: variable dereferenced before check 'cmnd'
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Acked-by: Douglas Gilbert <dgilbert@interlog.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
fixes warning:
warning: no previous prototype for ‘dump_sector’
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Acked-by: Douglas Gilbert <dgilbert@interlog.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Acked-by: Douglas Gilbert <dgilbert@interlog.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
use SCSI_W_LUN_REPORT_LUNS from scsi.h instead of localy defined
SAM2_WLUN_REPORT_LUNS
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Acked-by: Douglas Gilbert <dgilbert@interlog.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Use pr_fmt with both module name and __func__
Also drop few bare printk leftovers
The log format should stay pretty much intact
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Acked-by: Douglas Gilbert <dgilbert@interlog.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
do_device_access() takes a separate parameter to indicate the direction of
data transfer, which it used to use to select the appropriate function out
of sg_pcopy_{to,from}_buffer(). However these two functions now have
So this patch makes it bypass these wrappers and call the underlying
function sg_copy_buffer() directly; this has the same calling style as
do_device_access() i.e. a separate direction-of-transfer parameter and no
pointers-to-const, so skipping the wrappers not only eliminates the
warning, it also make the code simpler :)
[akpm@linux-foundation.org: fix very broken build]
Signed-off-by: Dave Gordon <david.s.gordon@intel.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
printk and friends can now format bitmaps using '%*pb[l]'. cpumask
and nodemask also provide cpumask_pr_args() and nodemask_pr_args()
respectively which can be used to generate the two printf arguments
necessary to format the specified cpu/nodemask.
* map_show()'s return value is too high by one and the function could
modify beyond the end of the buffer when the formatted text is long
enough.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: "James E.J. Bottomley" <James.Bottomley@HansenPartnership.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is the usual grab bag of driver updates (hpsa, storvsc, mp2sas,
megaraid_sas, ses) plus an assortment of minor updates. There's also an
update to ufs which adds new phy drivers and finally a new logging
infrastructure for SCSI.
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQEcBAABAgAGBQJU2Ty5AAoJEDeqqVYsXL0M9rAH/1xNpAxXuxQq+dW5Z+uOaX60
5RRIu7/xA1HEfzkT5FTHrolmogDjVqawu4PZS66iHDeo05RBVUlbTA8qCK+MlRcN
U6s0cLEw59eH3EaCfOGuYp/MnbhuV0eNxe0btmqJIQwuW3+gwZKGJdOq6LS2YasJ
k/DyIBVmkJAVsN56vm9q2vbtcZp+Bg+ngqBS+SC4TF7vV1WCtFmS6yaUf62PYW3D
+Irx37qHZntDR5wdw3dsuKDi5U8bl6myPjaVLnVJqg/WIF9RlCkjk5xpWT99AmVO
NmtYQxLLBlAQ5K+sIlBUwxZe+8q1l+Aj4TTmJHAfFtyfp25s7JR9I6/QtOyC5Kw=
=odol
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull first round of SCSI updates from James Bottomley:
"This is the usual grab bag of driver updates (hpsa, storvsc, mp2sas,
megaraid_sas, ses) plus an assortment of minor updates.
There's also an update to ufs which adds new phy drivers and finally a
new logging infrastructure for SCSI"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (114 commits)
scsi_logging: return void for dev_printk() functions
scsi: print single-character strings with seq_putc
scsi: merge consecutive seq_puts calls
scsi: replace seq_printf with seq_puts
aha152x: replace seq_printf with seq_puts
advansys: replace seq_printf with seq_puts
scsi: remove SPRINTF macro
sg: remove an unused variable
hpsa: Use local workqueues instead of system workqueues
hpsa: add in P840ar controller model name
hpsa: add in gen9 controller model names
hpsa: detect and report failures changing controller transport modes
hpsa: shorten the wait for the CISS doorbell mode change ack
hpsa: refactor duplicated scan completion code into a new routine
hpsa: move SG descriptor set-up out of hpsa_scatter_gather()
hpsa: do not use function pointers in fast path command submission
hpsa: print CDBs instead of kernel virtual addresses for uncommon errors
hpsa: do not use a void pointer for scsi_cmd field of struct CommandList
hpsa: return failed from device reset/abort handlers
hpsa: check for ctlr lockup after command allocation in main io path
...
cppcheck found the following issue:
(warning) Logical conjunction always evaluates to false:
alloc_len < 4 && alloc_len > 65535.
..the test should be instead:
if (alloc_len < 4 || alloc_len > 65536)
This error was introduced by recent commit 38d5c8336e
("scsi_debug: add Report supported opcodes+tmfs; Compare and write")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Accept the WRITE BUFFER command and do nothing other than
set the appropriate "microcode has been changed" UA on the LU.
>From an earlier patch by Doug Gilbert.
Signed-off-by: Ewan D. Milne <emilne@redhat.com>
Acked-by: Douglas Gilbert <dgilbert@interlog.com>
Tested-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Generate a REPORTED LUNS DATA HAS CHANGED Unit Attention if
sysfs "max_luns" is used to change the number of scsi_debug LUNs.
This is only done if scsi_debug_scsi_level is SPC-3 or above.
Additionally, implement SPC-4 behavior which only generates
this Unit Attention on the first LUN on the target to receive
a command after the change. This condition is cleared when
a REPORT LUNS command is received.
Signed-off-by: Ewan D. Milne <emilne@redhat.com>
Acked-by: Douglas Gilbert <dgilbert@interlog.com>
Tested-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
This eliminates a superfluous log message when the capacity is changed:
"check_readiness: unexpected unit attention code=3"
Signed-off-by: Ewan D. Milne <emilne@redhat.com>
Acked-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
All other traversals of the sdebug_host_list take the lock.
Signed-off-by: Ewan D. Milne <emilne@redhat.com>
Acked-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Kernel build tools pointed out a memory leak so that has been
fixed and its error paths strengthened with a goto. Testing
showed compare and write was only working for lba=0; correcting
the length of the LBA field fixed that.
Signed-off-by: Douglas Gilbert <dgilbert@interlog.com>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
For SPI drivers use the message definitions from scsi.h, and for target
drivers introduce a new TCM_*_TAG namespace.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com
Since we got rid of ordered tag support in 2010 the prime use case of
switching on and off ordered tags has been obsolete. The other function
of enabling/disabling tagging entirely has only been correctly implemented
by the 53c700 driver and isn't generally useful.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com
Reviewed-by: Hannes Reinecke <hare@suse.de>
The Report supported operation codes command is very closely integrated
into the table driven parser and very useful for testing it. Its cdb
masks form the basis of the 'strict' parameter's checks. The Report
supported TMFs command is a simple extension. The Compare and write
command may even be useful, as it should be atomic due to the read-write
lock that the driver uses on its backing store (ram).
Signed-off-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
The existing 'big switch' parser in queuecommand() is changed to
a table driven parser. The old and new queuecommand() were moved
in the source so diff would not shuffle them. Apart from the new
tables most other changes are refactoring existing response code
to be more easily called out of the table parser. The 'strict'
parameter is added so that cdb_s can be checked for non-zero
values in parts of the cdb that are reserved. Some other changes
include: tweak request sense response when D_SENSE differs; support
NDOB in Write Same(16); and fix crash in Get LBA Status when LBP
was inactive.
Signed-off-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Via sysfs the virtual_gb scsi_debug parameter can be changed while
LUs are in use. If that changes, the 'Capacity data has changed'
Unit Attention is queued on all LUs.
Signed-off-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
The way the existing scsi_debug command parser associated various
inject error flags to a command was difficult to replicate in the
table driven parser. This patch adds infrastructure to append those
flags to the end of a scsi_cmnd object with the cmd_size host
template option.
Signed-off-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Use Sense Key Specific field in the sense data of an ILLEGAL REQUEST
to optionally pinpoint the location of the problem field. This may
be either in the cdb or the associated parameter list.
Signed-off-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Drop the now unused reason argument from the ->change_queue_depth method.
Also add a return value to scsi_adjust_queue_depth, and rename it to
scsi_change_queue_depth now that it can be used as the default
->change_queue_depth implementation.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Reviewed-by: Hannes Reinecke <hare@suse.de>
All drivers use the implementation for ramping the queue up and down, so
instead of overloading the change_queue_depth method call the
implementation diretly if the driver opts into it by setting the
track_queue_depth flag in the host template.
Note that a few drivers validated the new queue depth in their
change_queue_depth method, but as we never go over the queue depth
set during slave_configure or the sysfs file this isn't nessecary
and can safely be removed.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Venkatesh Srinivas <venkateshs@google.com>
Now that we also get proper values in cmd->request->tag for untagged
commands, there is no need to force tagged_supported to on in drivers
that need host-wide tags.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Remove the tagged argument from scsi_adjust_queue_depth, and just let it
handle the queue depth. For most drivers those two are fairly separate,
given that most modern drivers don't care about the SCSI "tagged" status
of a command at all, and many old drivers allow queuing of multiple
untagged commands in the driver.
Instead we start out with the ->simple_tags flag set before calling
->slave_configure, which is how all drivers actually looking at
->simple_tags except for one worke anyway. The one other case looks
broken, but I've kept the behavior as-is for now.
Except for that we only change ->simple_tags from the ->change_queue_type,
and when rejecting a tag message in a single driver, so keeping this
churn out of scsi_adjust_queue_depth is a clear win.
Now that the usage of scsi_adjust_queue_depth is more obvious we can
also remove all the trivial instances in ->slave_alloc or ->slave_configure
that just set it to the cmd_per_lun default.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Most drivers use exactly the same implementation, so provide it as a
library function.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
The kernel used to contain two functions for length-delimited,
case-insensitive string comparison, strnicmp with correct semantics and
a slightly buggy strncasecmp. The latter is the POSIX name, so strnicmp
was renamed to strncasecmp, and strnicmp made into a wrapper for the new
strncasecmp to avoid breaking existing users.
To allow the compat wrapper strnicmp to be removed at some point in the
future, and to avoid the extra indirection cost, do
s/strnicmp/strncasecmp/g.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
A deadlock has been reported when the completion
of SCSI commands (simulated by a timer) was surprised
by a module removal. This patch removes one half of
the offending locks around timer deletions. This fix
is applied both to stop_all_queued() which is were
the deadlock was discovered and stop_queued_cmnd()
which has very similar logic.
This patch should be applied both to the lk 3.17 tree
and Christoph's drivers-for-3.18 tree.
Tested-and-reported-by: Milan Broz <gmazyland@gmail.com>
Signed-off-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Since a lot of functionality from SPC-4 is supported by this
driver (e.g. LBP and PI) then bump the default INQUIRY version
from SPC-3 to SPC-4. Also update the INQUIRY version
descriptors.
Signed-off-by: Douglas Gilbert <dgilbert@interlog.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Give existing errors priority over the generation of Task
Set Full (TSF) errors. So that max_queue is not exceeded,
existing errors may be sent back in the invocation thread.
This is done so errors like Unit Attentions are not hidden
and lost by either max_queue exceeded or real/injected
TSFs.
Signed-off-by: Douglas Gilbert <dgilbert@interlog.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
This patch removes a NULL check for the scsi_cmnd::cmnd pointer
since many other instances in this driver and elsewhere assume
it is valid. Also redundant casts to 'unsigned char *' are removed
as the pointer has that type.
Signed-off-by: Douglas Gilbert <dgilbert@interlog.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
- add host_lock option whose default value is 0 which removes the
host_lock around all queued commands
- accept delay=-1 (_hi_) or -2 which use a tasklet to invoke
the scsi_done callback into the mid-layer. The default
is still delay=1 which uses a timer to delay 1 jiffy
- wire .change_queue_depth and .change_queue_type
functions to better simulate queueing in a modern LLD
- add SCSI_DEBUG_OPT_Q_NOISE (0x200) mask to only produce
debug output associated with queue full, plus from
.change_queue_depth and .change_queue_type functions
- add SCSI_DEBUG_OPT_ALL_TSF (0x400) mask which reports
all queued_arr fulls at TASK_SET_FULL, otherwise
SCSI_MLQUEUE_HOST_BUSY is returned
- add SCSI_DEBUG_OPT_RARE_TSF (0x800) mask which works
together with the every_nth option (> 0) to count
occurrences of num_in_q==queue_depth. When every_nth
is reached the victim (a command) yields TASK SET FULL
- clean up many debug messages.
- add ndelay=<nanosecs> option that uses high resolution
timers; active if > 0 and then overrides delay= option
- expand Unit Attention handling: POR, BUS_RESET and
MODE PARAMETERS CHANGED
- support .eh_target_reset_handler and drop .bios_param
- add OPT_N_WCE mask so caching page yields WCE=0
- add OPT_RESET_NOISE mask to log aborts and resets
- add OPT_NO_CDB_NOISE mask to not log each cdb
- MODE SELECT support for changing caching page's WCE
- name common ioctls in log
- when fake_rw=1, do not vmalloc fake store; make
UNMAP and WRITE SAME obey fake_rw
- more logging and code improvements including better
sense buffer handling
With fio and four (pseudo) devices I have observed 1.2 M IOPS
on my equipment. Rob Elliott who has done much testing and made
numerous suggestions, has better IOPS results than mine.
Signed-off-by: Douglas Gilbert <dgilbert@interlog.com>
Reviewed-by: Robert Elliott <elliott@hp.com>
Tested-by: Robert Elliott <elliott@hp.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
The SCSI standard defines 64-bit values for LUNs, and large arrays
employing large or hierarchical LUN numbers become more and more
common.
So update the linux SCSI stack to use 64-bit LUN numbers.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Christoph Hellwig <hch@infradead.org>
Reviewed-by: Ewan Milne <emilne@redhat.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
This change enables to test read/write commands with huge transfer
length such as 1GB. For example:
# modprobe scsi_debug dev_size_mb=1024 clustering=1 opts=1
# cat /sys/block/$DEV/queue/max_hw_sectors_kb > \
/sys/block/$DEV/queue/max_sectors_kb
# fio --name=test --rw=write --bs=1g --size=1g --filename=/dev/$DEV \
--mem=mmaphuge --direct=1
The data type of max_sectors in scsi_host_template has been extended
to unsigned int by the previous change. So we can increase it from
0xffff to 0xffffffff to allow such huge transfer length.
Also, this increases sg_tablesize and max_segment_size, otherwise the
maximum transfer length is limited to 64MB.
(sg_tablesize * max_segment_size = 256 * 256KB)
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Acked by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Add an option to only transfer half the data for every n-th command.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Douglas Gilbert <dgilbert@interlog.com>
Reviewed-by: Nicholas Bellinger <nab@linux-iscsi.org>
This adds a module parameter to enable clustering.
Without enabling clustering support, the transfer length for read and
write scsi commands is limited upto 8MB when page size is 4KB and
sg_tablesize is 2048 (= SCSI_MAX_SG_CHAIN_SEGMENTS). I would like to
test commands with more than that transfer length.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Reviewed-by: Douglas Gilbert <dgilbert@interlog.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This change ensures that concurrent device access including ramdisk
storage, protection info, and provisioning map by read, write, and
unmap commands are protected with atomic_rw spinlock.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Reviewed-by: Douglas Gilbert <dgilbert@interlog.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Currently, clustering support for scsi_debug is disabled. This is
because there are for_each_sg() loops which assume that each sg list
element is consisted with a single page. But enabling clustering
support, each sg list element for scsi commands can be consisted with
multiple pages.
This replaces these for_each_sg() loops with sg mapping iterator which
is capable of handling each sg list element is consisted with multiple
pages.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Reviewed-by: Douglas Gilbert <dgilbert@interlog.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
When resp_xdwriteread() can't allocate temporary buffer, it returns -1.
But the return value is used as scsi status code and -1 is not
interpreted as correct code.
target_core_mod has similar xdwriteread emulation code. So this mimics
what target_core_mod does for xdwriteread when running out of memory.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Reviewed-by: Douglas Gilbert <dgilbert@interlog.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
It is unnecessary to increase dif_errors in dif_verify(), because the
caller will increment it when dif_verify() detects failure.
This bug was introduced by commit beb40ea42b ("[SCSI] scsi_debug:
reduce duplication between prot_verify_read and prot_verify_write")
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Acked-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
As pseudo_primary is only used in scsi_debug.c, it should be static.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Reviewed-by: Douglas Gilbert <dgilbert@interlog.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Reading partially unwritten sectors generates a false positive logical
block reference tag check failure when DIF is enabled.
This bug is caused by missing ei_lba increment in loop of dif_verify()
when unwritten sector is skipped.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Acked-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Instead of repeatedly calling driver_create_file() to create driver
attribute files, This achieves the same thing by constructing an array
of driver_attribute and setting it to bus_type->drv_groups.
This change simplifies both creation and destruction of the attribute
files, and also removes sparse warning caused by driver_attributes which
are unnecessarily declared as global.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Acked-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Each member in data integrity field tuple is big-endian. But the
endianness of the values being compared with these members are not
annotated. So this fixes these sparse warnings.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Acked-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
In the module initialization, invalid value for guard module parameter
is detected by the following check:
if (scsi_debug_guard > 1) {
printk(KERN_ERR "scsi_debug_init: guard must be 0 or 1\n");
return -EINVAL;
}
But this check isn't enough, because the type of scsi_debug_guard is
'int' and scsi_debug_guard could be a negative value.
This fixes it by changing the type of scsi_debug_guard to 'unsigned int'
instead of adding extra check for a negative value.
Reported-by: Joe Perches <joe@perches.com>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Acked-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
If data integrity support is enabled, prot_verify_write() is called in
response to WRITE commands and it verifies protection info from
prot_sglist by comparing against data sglist, and copies protection info
to dif_storep.
When multiple blocks are transfered by a WRITE command, it verifies and
copies these blocks one by one. So if it fails to verify protection
info in the middle of blocks, the actual data transfer to fake_storep
isn't proceeded at all although protection info for some blocks are
already copied to dif_storep. Therefore, it breaks the data integrity
between fake_storep and dif_storep.
This fixes it by ensuring that copying protection info to dif_storep is
done after all blocks are successfully verified. Reusing dif_copy_prot()
with supporting the opposite direction simplifies this fix.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Acked-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
If data integrity support is enabled, prot_verify_read() is called in
response to READ commands and it verifies protection info from dif_storep
by comparing against fake_storep, and copies protection info to
prot_sglist.
This factors out the portion of copying protection info into a separate
function. It will also be reused in the next change after supporting
the opposite direction (copying prot_sglist to dif_storep).
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Acked-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
If the module parameter virtual_gb is greater than 0, the READ command
may request the blocks which exceed actual ramdisk storage (fake_storep).
prot_verify_read() should treat those blocks as wrap around the end of
fake_storep. But it actually causes fake_storep and dif_storep buffer
overruns.
This fixes these buffer overruns. In order to simplify the fix,
this also introduces fake_store() and dif_store() which return
corresponding wrap around addresses.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Acked-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Commit b90ebc3d5c ("[SCSI] scsi_debug:
fix logical block provisioning support") fixed several issues with
logical block provisioning support, but it still doesn't properly fix
the cases when unmap_alignment > 0.
For example, load scsi_debug module with the following module parameters
and make all blocks mapped by filling the storage with zero.
# modprobe scsi_debug lbpu=1 unmap_alignment=1 unmap_granularity=4
# dd if=/dev/zero of=$DEV
Then, try to unmap the first unmappable blocks at lba=1, but GET LBA STATUS
unexpectedly reports that the last UNMAP has done nothing.
# sg_unmap --lba=1 --num=4 $DEV
# sg_get_lba_status --lba=1 $DEV
descriptor LBA: 0x0000000000000001 blocks: 16383 mapped
The problem is in map_index_to_lba(), which should return the first
LBA which is corresponding to a given index of provisioning map
(map_storep).
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Acked-by: "Martin K. Petersen" <martin.petersen@oracle.com>
Acked-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
With module parameter num_parts > 0, partition table is built on the
ramdisk storage when loading the driver. Unfortunately, there is an
endianness bug in sdebug_build_parts(). So the partition table is not
correctly initialized on big-endian systems.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Tested-by: Martin Peschke <mpeschke@linux.vnet.ibm.com>
Acked-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This is the remaining set of SCSI patches for the merge window. it's mostly
driver updates (scsi_debug, qla2xxx, storvsc, mp3sas). There are also several
bug fixes in fcoe, libfc, and megaraid_sas. We also have a couple of core
changes to try to make device destruction more deterministic.
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iQEcBAABAgAGBQJR4NdLAAoJEDeqqVYsXL0MgLcIAIMpnHPPO0xTB1brAhIA2r4H
MHcD3/iRu+b+YuzEOuErw+pNzsAUGG9MD1b4m74qZ4z9PaVl4U0lWt61++P/OW91
ZD9TAF70t+3/R6Wz2eZp8WqmgWkLcEu9wDQxJKGPCcyWB9MphbsxaakM60B1swCy
5H3VGBWOy8MieLCHzdYgXfB83fnSy/75h/jErDiNwoEUuRci0rb9yOtpNamXPOiB
2JpW8hegixdup6srt+4Uq3gSWKJhqV1MD3leu6i3cHmoqTGueCX46patqlciSLRo
lN8fB3RgZjtIj8zattaeaGchEUMAE7yKcbjC+LyGPQe3+DKVutGNrEFT68KKRcQ=
=7slg
-----END PGP SIGNATURE-----
Merge tag 'scsi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull final round of SCSI updates from James Bottomley:
"This is the remaining set of SCSI patches for the merge window. It's
mostly driver updates (scsi_debug, qla2xxx, storvsc, mp3sas). There
are also several bug fixes in fcoe, libfc, and megaraid_sas. We also
have a couple of core changes to try to make device destruction more
deterministic"
* tag 'scsi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (46 commits)
[SCSI] scsi constants: command, sense key + additional sense strings
fcoe: Reduce number of sparse warnings
fcoe: Stop fc_rport_priv structure leak
libfcoe: Fix meaningless log statement
libfc: Differentiate echange timer cancellation debug statements
libfc: Remove extra space in fc_exch_timer_cancel definition
fcoe: fix the link error status block sparse warnings
fcoe: Fix smatch warning in fcoe_fdmi_info function
libfc: Reject PLOGI from nodes with incompatible role
[SCSI] enable destruction of blocked devices which fail LUN scanning
[SCSI] Fix race between starved list and device removal
[SCSI] megaraid_sas: fix a bug for 64 bit arches
[SCSI] scsi_debug: reduce duplication between prot_verify_read and prot_verify_write
[SCSI] scsi_debug: simplify offset calculation for dif_storep
[SCSI] scsi_debug: invalidate protection info for unmapped region
[SCSI] scsi_debug: fix NULL pointer dereference with parameters dif=0 dix=1
[SCSI] scsi_debug: fix incorrectly nested kmap_atomic()
[SCSI] scsi_debug: fix invalid address passed to kunmap_atomic()
[SCSI] mpt3sas: Bump driver version to v02.100.00.00
[SCSI] mpt3sas: when async scanning is enabled then while scanning, devices are removed but their transport layer entries are not removed
...
do_device_access() is a function that abstracts copying SG list from/to
ramdisk storage (fake_storep).
It must deal with the ranges exceeding actual fake_storep size, because
such ranges are valid if virtual_gb is set greater than zero, and they
should be treated as fake_storep is repeatedly mirrored up to virtual
size.
Unfortunately, it can't deal with the range which wraps around the end of
fake_storep. A wrap around range is copied by two
sg_copy_{from,to}_buffer() calls, but sg_copy_{from,to}_buffer() can't
copy from/to in the middle of SG list, therefore the second call can't
copy correctly.
This fixes it by using sg_pcopy_{from,to}_buffer() that can copy from/to
the middle of SG list.
This also simplifies the assignment of sdb->resid in
fill_from_dev_buffer(). Because fill_from_dev_buffer() is now only called
once per command execution cycle. So it is not necessary to take care to
decrease sdb->resid if fill_from_dev_buffer() is called more than once.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: "James E.J. Bottomley" <JBottomley@parallels.com>
Cc: Douglas Gilbert <dgilbert@interlog.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Horia Geanta <horia.geanta@freescale.com>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Tejun Heo <tj@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In order to reduce code duplication between prot_verify_read() and
prot_verify_write(), this moves common code into the new functions.
[jejb: fix unitialised variable warning]
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Acked-by: Douglas Gilbert <dgilbert@interlog.com>
Acked-by: "Martin K. Petersen" <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
dif_storep is declared as pointer to unsigned char type. But it is
actually used to store vmalloced array of struct sd_dif_tuple.
This changes the type of dif_storep to the pointer to struct sd_dif_tuple.
It simplifies offset calculation for dif_storep and enables to remove
hardcoded size of struct sd_dif_tuple.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Acked-by: Douglas Gilbert <dgilbert@interlog.com>
Acked-by: "Martin K. Petersen" <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
When UNMAP command is issued with the data integrity support enabled,
the protection info for the unmapped region is remain unchanged.
So READ command for the region later on causes data integrity failure.
This fixes it by invalidating protection info for the unmapped region
by filling with 0xff pattern.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Acked-by: Douglas Gilbert <dgilbert@interlog.com>
Acked-by: "Martin K. Petersen" <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The protection info dif_storep is allocated only when parameter dif is
not zero. But it will be accessed when reading or writing to the storage
installed with parameter dix is not zero.
So kernel crashes if scsi_debug module is loaded with parameters dix=1 and
dif=0.
This fixes it by making dif_storep available if parameter dix is not zero
instead of checking if parameter dif is not zero.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Acked-by: Douglas Gilbert <dgilbert@interlog.com>
Acked-by: "Martin K. Petersen" <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
In the function prot_verify_write(), kmap_atomic()/kunmap_atomic() for
data page and kmap_atomic()/kunmap_atomic() for protection information
page are not nested each other.
It worked perfectly before commit 3e4d3af501
("mm: stack based kmap_atomic()"). Because the kmap_atomic slot KM_IRQ0
was used for data page and the slot KM_IRQ1 was used for protection page.
But KM_types are gone and kmap_atomic() is using stack based implementation.
So two different kmap_atomic() usages must be strictly nested now.
This change ensures kmap_atomic() usage is strictly nested.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Acked-by: Douglas Gilbert <dgilbert@interlog.com>
Acked-by: "Martin K. Petersen" <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
In the function prot_verify_write(), the kmap address 'daddr' is
incremented in the loop for each data page. Finally 'daddr' reaches
the next page boundary in the end of the loop, and the invalid address
is passed to kunmap_atomic().
Fix the issue by not incrementing 'daddr' in the loop and offsetting it
by the loop counter on demand.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Acked-by: Douglas Gilbert <dgilbert@interlog.com>
Acked-by: "Martin K. Petersen" <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
provisioning map (map_storep) is a bitmap accessed by bitops.
So the allocation size should be a multiple of sizeof(unsigned long) and
also the bitmap should be cleared by using bitmap_clear() instead of
memset().
Otherwise it will cause problem on big-endian architecture if the number of
bits is not a multiple of BITS_PER_LONG.
I tried testing the logical block provisioning support in scsi_debug,
but it didn't work as I expected.
For example, load scsi_debug module with UNMAP command supported
and fill the storage with random data.
# modprobe scsi_debug lbpu=1
# dd if=/dev/urandom of=/dev/sdb
Then, try to unmap LBA 0, but Get LBA status reports:
# sg_unmap --lba=0 --num=1 /dev/sdb
# sg_get_lba_status --lba=0 /dev/sdb
descriptor LBA: 0x0000000000000000 blocks: 16384 mapped
This is unexpected result. Because UNMAP command to LBA 0 finished
without any errors, but Get LBA status shows that LBA 0 is still mapped.
This problem is due to the wrong translation between LBA and index of
provisioning map. Fix it by using correct translation functions.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Acked-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The function unmap_region() clears memory region specified as the logical
block address and the number of logical blocks in ramdisk storage
(fake_storep) if lbpu and lbprz module parameters are enabled.
In the while loop of unmap_region(), it advances optimal unmap granularity
in logical blocks. But it only clears one logical block at LBA 'block' per
loop iteration. And furthermore, the 'block' is not pointing to a logical
block address which should be cleared, it is a index of probisioning map
(map_storep).
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Acked-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
scsi_debug prohibits setting scsi_debug_unmap_alignment to be greater
than scsi_debug_unmap_granularity. But setting them to be the same value
is not prohibited. In this case, the only difference with
scsi_debug_unmap_alignment == 0 is the logical blocks from 0 to
scsi_debug_unmap_alignment - 1 cannot be unmapped. But the difference is
not properly handled in the current code.
So this prohibits such unusual setting.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Acked-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
If the logical block provisioning is not enabled, map_region() and
unmap_region() have no effect and they don't need to be called.
So this makes map_region() and unmap_region() to be called only
when scsi_debug_lbp() returns true, i.e. logical block provisioning is
enabled.
While I'm at it, this also removes meaningless non-zero check for
scsi_debug_unmap_granularity.
Because scsi_debug_unmap_granularity cannot be zero with usual setting:
scsi_debug_unmap_granularity is 1 by default, and it can be changed to
zero with explicit module parameter setting only when the logical block
provisioning is disabled. But it is only meaningful module parameter
when the logical block provisioning is enabled.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Acked-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Currently it is possible to unmap one more block than user requested to
due to the off-by-one error in unmap_region(). This is probably due to
the fact that the end variable despite its name actually points to the
last block to unmap + 1. However in the condition it is handled as the
last block of the region to unmap.
The bug was not previously spotted probably due to the fact that the
region was not zeroed, which has changed with commit
be1dd78de5. With that commit we were able
to corrupt the ext4 file system on 256M scsi_debug device with LBPRZ
enabled using fstrim.
Since the 'end' semantic is the same in several functions there this
commit just fixes the condition to use the 'end' variable correctly in
that context.
Reported-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Lukas Czerner <lczerner@redhat.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Acked-by: Douglas Gilbert <dgilbert@interlog.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Add "removable" module parameter to set the "removable" attribute of any
subsequently created debug block device. It is a writable driver option, so
that you can switch between removable and "fixed" media block devices in
between the add_host calls.
This is useful for being able to test the different behaviour/required
privileges in e. g. the udisks test suite.
Signed-off-by: Martin Pitt <martin.pitt@ubuntu.com>
Acked-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iQEcBAABAgAGBQJPdrIWAAoJEDeqqVYsXL0Mny4IAMTzXGOXCykpWhdIe2R8w0Ys
eIoTJhBKoQWnLTV8cOODtwmtZcoQLeXkZmizZiAJvX6O1tOgueg+W4AFa9grxXGI
O0d1bSb2ardzU7VZrZSY60Hd4bylMwn4Xv/0dRrQMwTJO0LEeGWsJPV2+2BuXwMB
lGCNB67oUBXgMOI1jUZQRwx/mBzQ3e/gINjnpZTNKHia7YkX/yVTFISq7htgfDN7
1wRGxymbHtVap3NbtUO96BUUndAiF5vom+4WNvaQUyPrCc6aoGWjv+J9DQXY/zgv
AYjujAluK396D6YncGFAWBzYOg9WFbq54v0PRUanjcTTAu5ILs2BxqWdhmnvl14=
=IH8T
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6
Pull SCSI updates from James Bottomley:
"This is primarily another round of driver updates (lpfc, bfa, fcoe,
ipr) plus a new ufshcd driver. There shouldn't be anything
controversial in here (The final deletion of scsi proc_ops which
caused some build breakage has been held over until the next merge
window to give us more time to stabilise it).
I'm afraid, with me moving continents at exactly the wrong time,
anything submitted after the merge window opened has been held over to
the next merge window."
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (63 commits)
[SCSI] ipr: Driver version 2.5.3
[SCSI] ipr: Increase alignment boundary of command blocks
[SCSI] ipr: Increase max concurrent oustanding commands
[SCSI] ipr: Remove unnecessary memory barriers
[SCSI] ipr: Remove unnecessary interrupt clearing on new adapters
[SCSI] ipr: Fix target id allocation re-use problem
[SCSI] atp870u, mpt2sas, qla4xxx use pci_dev->revision
[SCSI] fcoe: Drop the rtnl_mutex before calling fcoe_ctlr_link_up
[SCSI] bfa: Update the driver version to 3.0.23.0
[SCSI] bfa: BSG and User interface fixes.
[SCSI] bfa: Fix to avoid vport delete hang on request queue full scenario.
[SCSI] bfa: Move service parameter programming logic into firmware.
[SCSI] bfa: Revised Fabric Assigned Address(FAA) feature implementation.
[SCSI] bfa: Flash controller IOC pll init fixes.
[SCSI] bfa: Serialize the IOC hw semaphore unlock logic.
[SCSI] bfa: Modify ISR to process pending completions
[SCSI] bfa: Add fc host issue lip support
[SCSI] mpt2sas: remove extraneous sas_log_info messages
[SCSI] libfc: fcoe_transport_create fails in single-CPU environment
[SCSI] fcoe: reduce contention for fcoe_rx_list lock [v2]
...
The page length for the 0xb2 VPD page is defined to be 4 bytes when no
provisioning descriptors are provided (DP=0).
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Acked-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Add LBPRZ support to scsi_debug; i.e. read zeros for
unmapped blocks.
Rather than checking for unmapped blocks at
read time, this just zeroes them on the backing store
at unmap time so it behaves the same way.
This also adds a module parameter to disable it.
lbprz, "unmapped blocks return 0 on read (def=1)"
[jejb: fix whitespace errors]
Signed-off-by: Eric Sandeen <sandeen@redhat.com>
Acked-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iQEcBAABAgAGBQJPZxSnAAoJEDeqqVYsXL0M0Y4IAMX0vrTVZbg6psA5/gMcWGRP
CkFXEQ8n0PL2SCaj6BoDqamJFe5Nc7dnqxM0fGawB4S9vr3rHhiOlwO+NbV9zFYC
2skBTpeL3sjgtN/jTBdfeeAa7xTYpu/XGyei0NS1A5c2AyMVXV0uYV2s4VNZxe44
tVIn1OEzM2giZ9EB1OZslDMrg5XXm3MBIUECP0LbWUhBm/35caSFKzMXRwhh7WiK
+AVmc2AZYtdEwuknDyiH7KlsaoB3vGL9pPrAUJzIgEhy2pOo2A7W72HfA4Fj+y6a
uF9HBS5zciMp1+sGWry62AjNbWgin9BRlozBEO/lJhIfMGDV1nXEIJsOkOgkdoE=
=1TxB
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6
SCSI updates from James Bottomley:
"The update includes the usual assortment of driver updates (lpfc,
qla2xxx, qla4xxx, bfa, bnx2fc, bnx2i, isci, fcoe, hpsa) plus a huge
amount of infrastructure work in the SAS library and transport class
as well as an iSCSI update. There's also a new SCSI based virtio
driver."
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (177 commits)
[SCSI] qla4xxx: Update driver version to 5.02.00-k15
[SCSI] qla4xxx: trivial cleanup
[SCSI] qla4xxx: Fix sparse warning
[SCSI] qla4xxx: Add support for multiple session per host.
[SCSI] qla4xxx: Export CHAP index as sysfs attribute
[SCSI] scsi_transport: Export CHAP index as sysfs attribute
[SCSI] qla4xxx: Add support to display CHAP list and delete CHAP entry
[SCSI] iscsi_transport: Add support to display CHAP list and delete CHAP entry
[SCSI] pm8001: fix endian issue with code optimization.
[SCSI] pm8001: Fix possible racing condition.
[SCSI] pm8001: Fix bogus interrupt state flag issue.
[SCSI] ipr: update PCI ID definitions for new adapters
[SCSI] qla2xxx: handle default case in qla2x00_request_firmware()
[SCSI] isci: improvements in driver unloading routine
[SCSI] isci: improve phy event warnings
[SCSI] isci: debug, provide state-enum-to-string conversions
[SCSI] scsi_transport_sas: 'enable' phys on reset
[SCSI] libsas: don't recover end devices attached to disabled phys
[SCSI] libsas: fixup target_port_protocols for expanders that don't report sata
[SCSI] libsas: set attached device type and target protocols for local phys
...
We have experienced several devices which fail in a fashion we do not
currently handle gracefully in SCSI. After a failure these devices will
respond to the SCSI primary command set (INQUIRY, TEST UNIT READY, etc.)
but any command accessing the storage medium will time out.
The following patch adds an callback that can be used by upper level
drivers to inspect the results of an error handling command. This in
turn has been used to implement additional checking in the SCSI disk
driver.
If a medium access command fails twice but TEST UNIT READY succeeds both
times in the subsequent error handling we will offline the device. The
maximum number of failed commands required to take a device offline can
be tweaked in sysfs.
Also add a new error flag to scsi_debug which allows this scenario to be
easily reproduced.
[jejb: fix up integer parsing to use kstrtouint]
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The SCSI GET LBA STATUS command was introduced in SBC-3 revision
20 in September 2009. At that time the Parameter Data Length
field in the response had an associated byte offset of 8.
Then in SBC-3 revision 25 (October 2010) that byte offset was
changed to 4. The sg_get_lba_status utility in sg3_utils version
1.33 (released earlier today) has been changed to calculate
the newer response length. However the implementation of
GET LBA STATUS command in the scsi_debug driver still uses the
original byte offset.
modify the Parameter Data Length field value in the GET LBA STATUS command
response to comply with the change in SBC-3 revision 25
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Christoph Hellwig