Sync code to the same with tk4 pub/lts/0017-kabi, except deleted rue
and wujing. Partners can submit pull requests to this branch, and we
can pick the commits to tk4 pub/lts/0017-kabi easly.
Signed-off-by: Jianping Liu <frankjpliu@tencent.com>
Gitee limit the repo's size to 3GB, to reduce the size of the code,
sync codes to ock 5.4.119-20.0009.21 in one commit.
Signed-off-by: Jianping Liu <frankjpliu@tencent.com>
Typical SLI-4 hardware supports up to 2 4KB pages to be registered per XRI
to contain the exchanges Scatter/Gather List. This caps the number of SGL
elements that can be in the SGL. There are not extensions to extend the
list out of the 2 pages.
The G7 hardware adds a SGE type that allows the SGL to be vectored to a
different scatter/gather list segment. And that segment can contain a SGE
to go to another segment and so on. The initial segment must still be
pre-registered for the XRI, but it can be a much smaller amount (256Bytes)
as it can now be dynamically grown. This much smaller allocation can
handle the SG list for most normal I/O, and the dynamic aspect allows it to
support many MB's if needed.
The implementation creates a pool which contains "segments" and which is
initially sized to hold the initial small segment per xri. If an I/O
requires additional segments, they are allocated from the pool. If the
pool has no more segments, the pool is grown based on what is now
needed. After the I/O completes, the additional segments are returned to
the pool for use by other I/Os. Once allocated, the additional segments are
not released under the assumption of "if needed once, it will be needed
again". Pools are kept on a per-hardware queue basis, which is typically
1:1 per cpu, but may be shared by multiple cpus.
The switch to the smaller initial allocation significantly reduces the
memory footprint of the driver (which only grows if large ios are
issued). Based on the several K of XRIs for the adapter, the 8KB->256B
reduction can conserve 32MBs or more.
It has been observed with per-cpu resource pools that allocating a resource
on CPU A, may be put back on CPU B. While the get routines are distributed
evenly, only a limited subset of CPUs may be handling the put routines.
This can put a strain on the lpfc_put_cmd_rsp_buf_per_cpu routine because
all the resources are being put on a limited subset of CPUs.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
As dma_pool_destroy and mempool_destroy functions has NULL check. We may
not need NULL check before calling them.
Fix below warnings reported by coccicheck
./drivers/scsi/lpfc/lpfc_mem.c:252:2-18: WARNING: NULL check before some
freeing functions is not needed.
./drivers/scsi/lpfc/lpfc_mem.c:255:2-18: WARNING: NULL check before some
freeing functions is not needed.
./drivers/scsi/lpfc/lpfc_mem.c:258:2-18: WARNING: NULL check before some
freeing functions is not needed.
./drivers/scsi/lpfc/lpfc_mem.c:261:2-18: WARNING: NULL check before some
freeing functions is not needed.
./drivers/scsi/lpfc/lpfc_mem.c:265:2-18: WARNING: NULL check before some
freeing functions is not needed.
./drivers/scsi/lpfc/lpfc_mem.c:269:2-17: WARNING: NULL check before some
freeing functions is not needed.
Signed-off-by: Hariprasad Kelam <hariprasad.kelam@gmail.com>
Reviewed-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The driver data structure for managing a mailbox command contained two
context fields. Unfortunately, the context were considered "generic" to be
used at the whim of the command code. Of course, one section of code used
fields this way, while another did it that way, and eventually there were
mixups.
Refactored the structure so that the generic contexts become a node context
and a buffer context and all code standardizes on their use.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Change references from "Broadcom Limited" to "Broadcom Inc." in the
copyright message. Update copyright duration if not yet updated for 2018.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Updated Copyright in files updated 11.4.0.7
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When nvme target deferred receive logic waits for exchange resources,
the corresponding receive buffer is not replenished with the hardware.
This can result in a lack of asynchronous receive buffer resources in
the hardware, resulting in a "2885 Port Status Event: ... error
1=0x52004a01 ..." message.
Correct by replenishing the buffer whenenver the deferred logic kicks
in. Update corresponding debug messages and statistics as well.
[mkp: applied by hand]
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The error message dereferences "rqb_entry" so we need to print it first
and then free the buffer.
Fixes: 6c621a2229 ("scsi: lpfc: Separate NVMET RQ buffer posting from IO resources SGL/iocbq/context")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The PCI pool API is deprecated. This commit replaces the PCI pool old
API by the appropriate function with the DMA pool API. It also updates
some comments, accordingly.
Signed-off-by: Romain Perier <romain.perier@collabora.com>
Reviewed-by: Peter Senna Tschudin <peter.senna@collabora.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently IO resources are mapped 1 to 1 with RQ buffers posted
Added logic to separate RQE buffers from IO op resources
(sgl/iocbq/context). During initialization, the driver will determine
how many SGLs it will allocate for NVMET (based on what the firmware
reports) and associate a NVMET IOCBq and NVMET context structure with
each one.
Now that hdr/data buffers are immediately reposted back to the RQ, 512
RQEs for each MRQ is sufficient. Also, since NVMET data buffers are now
128 bytes, lpfc_nvmet_mrq_post is not necessary anymore as we will
always post the max (512) buffers per NVMET MRQ.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Using 2048 byte buffer and onle 128 bytes is needed.
Create nee LFPC_NVMET_DATA_BUF_SIZE define to use for NVMET RQ/MRQs.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
From: Colin Ian King <colin.king@canonical.com>
dma_buf->iocbq is being dereferenced immediately before it is
being null checked, so we have a potential null pointer dereference
bug. Fix this by only dereferencing it only once we have passed
a null check on the pointer.
Detected by CoverityScan, CID#1411652 ("Dereference before null check")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Update copyrights to 2017 for all files touched in this patch set
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
NVME Target: Tie in to NVME Fabrics nvmet_fc LLDD target api
Adds the routines to:
- register and deregister the FC port as a nvmet-fc targetport
- binding of nvme queues to adapter WQs
- receipt and passing of NVME LS's to transport, sending transport response
- receipt of NVME FCP CMD IUs, processing FCP target io data transmission
commands; transmission of FCP io response
- Abort operations for tgt io exchanges
[mkp: fixed space at end of file warning]
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
NVME Target: Base modifications
This set of patches adds the base modifications for NVME target support
The base modifications consist of:
- Additional module parameters or configuration tuning
- Enablement of configuration mode for NVME target. Ties into the
queueing model put into place by the initiator basemods patches.
- Target-specific buffer pools, dma pools, sgl pools
[mkp: fixed space at end of file]
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
NVME Initiator: Base modifications
This patch adds base modifications for NVME initiator support.
The base modifications consist of:
- Formal split of SLI3 rings from SLI-4 WQs (sometimes referred to as
rings as well) as implementation now widely varies between the two.
- Addition of configuration modes:
SCSI initiator only; NVME initiator only; NVME target only; and
SCSI and NVME initiator.
The configuration mode drives overall adapter configuration,
offloads enabled, and resource splits.
NVME support is only available on SLI-4 devices and newer fw.
- Implements the following based on configuration mode:
- Exchange resources are split by protocol; Obviously, if only
1 mode, then no split occurs. Default is 50/50. module attribute
allows tuning.
- Pools and config parameters are separated per-protocol
- Each protocol has it's own set of queues, but share interrupt
vectors.
SCSI:
SLI3 devices have few queues and the original style of queue
allocation remains.
SLI4 devices piggy back on an "io-channel" concept that
eventually needs to merge with scsi-mq/blk-mq support (it is
underway). For now, the paradigm continues as it existed
prior. io channel allocates N msix and N WQs (N=4 default)
and either round robins or uses cpu # modulo N for scheduling.
A bunch of module parameters allow the configuration to be
tuned.
NVME (initiator):
Allocates an msix per cpu (or whatever pci_alloc_irq_vectors
gets)
Allocates a WQ per cpu, and maps the WQs to msix on a WQ #
modulo msix vector count basis.
Module parameters exist to cap/control the config if desired.
- Each protocol has its own buffer and dma pools.
I apologize for the size of the patch.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
----
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This reverts commit 9be321819c which
caused a regression on hardware using the SLI3 interface.
Reported-by: Dick Kennedy <dick.kennedy@broadcom.com>
Cc: <stable@vger.kernel.org> # 4.6+
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <jejb@linux.vnet.ibm.com>
The mempool_destroy() function tests whether its argument is NULL
and then returns immediately. Thus the test around the calls is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: James Smart <james.smart@avagotech.com>
Reviewed-by: Hannes Reinicke <hare@suse.de>
Reviewed-by: Sebastian Herbszt <herbszt@gmx.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Update Copyright on changed files from 8.3.45 patches
Missed this in the 8.3.45 push
Signed-off-by: James Smart <james.smart@emulex.com>
Reviewed-By: Dick Kennedy <dick.kennedy@emulex.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
- Make lpfc_sli4_pci_mem_unset interface type aware (CR 124390)
- Convert byte count to word count when calling __iowrite32_copy (CR 122550)
- Checked the ERR1 and ERR2 registers for error attention due to SLI
Port state affected by forced debug dump. (CR 122986, 122426, 124859)
- Use the lpfc_readl routine instead of the readl for the port status
register read in lpfc_handle_eratt_s4 (CR 125403)
- Call lpfc_sli4_queue_destroy inside of lpfc_sli4_brdreset before doing
a pci function reset (CR 125124, 125168, 125572, 125622)
- Zero out the HBQ when it is allocated (CR 125663)
- Alter port reset log messages to indicate error type (CR 125989)
- Added proper NULL pointer checking to all the places that accessing
the queue memory (CR 125832)
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This patch adds support for hardware that returns resource ids via
extents rather than contiguous ranges.
[jejb: checkpatch.pl fixes]
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <jbottomley@parallels.com>
Added support for ELS RRQ command
- Add new routine lpfc_set_rrq_active() to track XRI qualifier state.
- Add new module parameter lpfc_enable_rrq to control RRQ operation.
- Add logic to ELS RRQ completion handler and xri qualifier timeout
to clear XRI qualifier state.
- Use OX_ID from XRI_ABORTED_CQE for RRQ payload.
- Tie abort and XRI_ABORTED_CQE andler to RRQ generation.
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
Update of copyrights on modified files
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Adds new hardware and interface definitions.
Adds new interface routines - utilizing the reorganized layout of the
driver. Adds SLI-4 specific functions for attachment, initialization,
teardown, etc.
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Added support for new sysfs attributes: lpfc_stat_data_ctrl and
lpfc_max_scsicmpl_time. The attributes control statistical reporting
of io load.
Added support for new fc vendor events for error reporting.
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Miscellaneous Fixes:
- Fix a couple of sparse complaints
- Reset the FCP recovery flag when the node is not a FCP2 device.
- Speed up offline prep delays
- Fixed a memory leak in lpfc_mem_alloc failure path
- Fixed external loopback test.
- Fixed error code returned from the driver when HBA is over heated.
- Correct Max NPIV vport to limits read from adapter
- Add missing locks around fc_flag and FC_NEEDS_REG_VPI
- Add missing hba ids for device identification
- Added support for SET_VARIABLE and MBX_WRITE_WWN mailbox commands
- Changed all temperature event messages from warning to error
- Fix reporting of link speed when link is down
- Added support for MBX_WRITE_WWN mailbox command
- Change del_timer_sync() in ISR to del_timer() in interrupt handler
- Correct instances of beXX_to_cpu() that should be cpu_to_beXX()
- Perform target flush before releasing node references on module unload
- Avoid bogus devloss_tmo messages when driver unloads
- Fix panic when HBA generates ERATT interupt
- Fix mbox race condition and a workaround on back-to-back mailbox commands
- Force NPIV off for pt2pt mode between 2 NPorts
- Stop worker thread before removing fc_host.
- Fix up discovery timeout error case due to missing clear_la
- Tighten mailbox polling code to speed up detection of fast completions
- Only allow DUMP_MEMORY if adapter offline due to overtemp errors
- Added extended error information to the log messages in chip init.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
- Fix vport ndlp ref counting errors
- Fix use after free of ndlp structure
- Use the correct flag to check for LOADING setting.
- Fix driver unload bugs (related to shost references) after link down or rscn
- Fix up HBQ initialization
- Fix port_list locking around driver unload.
- Fix references to hostdata as a phba
- Fix GFFID type offset to work correctly with big endian structure.
- Only call pci_disable_msi if the pci_enable_msi succeeded
- Fix vport_delete wait/fail if in discovery
- Put a reference on the nameservers ndlp when performing CT traffic.
- Remove unbalanced hba unlock.
- Fix up HBQ processing
- Fix lpfc debugfs discovery trace output for ELS rsp cmpl
- Send ADISC when rpi is 0
- Stop FDISC retrying forever
- Unable to retrieve correct config parameter for vport
- Fix sli_validate_fcp_iocb, sli_sum_iocb, sli_abort_iocb to be vport-aware.
- Fix index-out-of-range error in iocb. Spotted by Coverity.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Following the NPIV support, the following changes have been accumulated
in the testing and qualification of the driver:
- Fix affinity of ELS ring to slow/deferred event processing
- Fix Ring attention masks
- Defer dev_loss_tmo timeout handling to worker thread
- Consolidate link down error classification for better error checking
- Remove unused/deprecated nlp_initiator_tmr timer
- Fix for async scan - move adapter init code back into pci_probe_one
context. Fix async scan interfaces.
- Expand validation of ability to create vports
- Extract VPI resource cnt from firmware
- Tuning of Login/Reject policies to better deal with overwhelmned targets
- Misc ELS and discovery fixes
- Export the npiv_enable attribute to sysfs
- Mailbox handling fix
- Add debugfs support
- A few other small misc fixes:
- wrong return values, double-frees, bad locking
- Added adapter failure heartbeat
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
NPIV support is added to the driver. It utilizes the interfaces of
the fc transport for the creation and deletion of vports. Within the
driver, a new Scsi_Host is created for each NPIV instance, and is
paired with a new instance of a FC port. This allows N FC Port
elements to share a single Adapter.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
NPIV support is only available via new adapter interface extensions,
termed SLI-3. This interface changes some of the basic behaviors such
as command and response ring element sizes and data structures, as
well as a change in buffer posting. Note: the new firmware extensions
are found only on our mid-range and enterprise 4Gig adapters - so NPIV
support is available only on these newer adapters. The latest firmware
can be downloaded from the Emulex support page.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The driver is reorganized to separate the handling of the adapter from
the handling of the FC port. Adapter handling includes submissions of
command requests, receiving responses, and managing adapter resources.
The FC port includes the discovery engine, login handling, and the
mapping of a Scsi_Host on the "port". Although not a large functional
change, as it touches core structures and functions, resulting in a
large text delta.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Add kmalloc failure check and fix the loop on error path. Without the
patch pool element at index [0] will not be freed.
Signed-off-by: Mariusz Kozlowski <m.kozlowski@tuxland.pl>
Acked-by: James Smart <James.Smart@Emulex.Com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Fix memory leak and cleanup code related to per ring lookup array.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch changes several mempool users, all of which are basically just
wrappers around kmalloc(), to use the common mempool_kmalloc/kfree, rather
than their own wrapper function, removing a bunch of duplicated code.
Signed-off-by: Matthew Dobson <colpatch@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Replace use of lpfc_put_lun with midlayer's int_to_scsilun
Remove driver's local definition of lpfc_put_lun (which converts an
int back to a 64-bit LUN) and replace it's use with the recently added
int_to_scsilun function provided by the midlayer.
Note: Embedding midlayer structure in our structure caused
need for more files to include midlayer headers.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Fix panic in lpfc_get_stats()
Symptoms: Panic on sysfs stats access
Cause: In lpfc_get_stats() we are writing to memory that we do not
own.
Fix: Fix our stats structure allocation. Embed phba->link_stats in
struct lpfc_hba and stop treating it like rogue structure.
Note: Embedding midlayer/transport structure in our structure caused
need for more files to include midlayer/transport headers.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Update copyright notice text and include year 2005.
Add Copyright notice for Christoph Hellwig to several files: lpfc.h
lpfc_attr.c lpfc_els.c lpfc_hbadisc.c lpfc_init.c lpfc_mbox.c
lpfc_mem.c lpfc_nportdisc.c lpfc_scsi.c lpfc_sli.c
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Jianping Liu