Sync code to the same with tk4 pub/lts/0017-kabi, except deleted rue
and wujing. Partners can submit pull requests to this branch, and we
can pick the commits to tk4 pub/lts/0017-kabi easly.
Signed-off-by: Jianping Liu <frankjpliu@tencent.com>
Gitee limit the repo's size to 3GB, to reduce the size of the code,
sync codes to ock 5.4.119-20.0009.21 in one commit.
Signed-off-by: Jianping Liu <frankjpliu@tencent.com>
Sync kernel codes to the same with 590eaf1fec ("Init Repo base on
linux 5.4.32 long term, and add base tlinux kernel interfaces."), which
is from tk4, and it is the base of tk4.
Signed-off-by: Jianping Liu <frankjpliu@tencent.com>
Convert the remaining %pf users to %ps to prepare for the removal of the
old %pf conversion specifier support.
Fixes: 3235066449 ("scsi: lpfc: Migrate to %px and %pf in kernel print calls")
Link: https://lore.kernel.org/r/20190904160423.3865-1-sakari.ailus@linux.intel.com
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In order to see real addresses, convert %p with %px for kernel addresses
and replace %p with %pf for functions.
While converting, standardize on "x%px" throughout (not %px or 0x%px).
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
GetTrunkInfo is displaying an incorrect link speed when the link is a trunk
and the link has gone down. The driver is not clearing the logical speed
as part of the link down transition.
Fix by setting the logical speed to UNKNOWN SPEED when the link goes down.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
During cable pull testing a deadlock was seen between lpfc_nlp_counters()
vs lpfc_mbox_process_link_up() vs lpfc_work_list_done(). They are all
waiting on the shost->host_lock.
Issue is all of these cases raise irq when taking out the lock but use
spin_unlock_irq() when unlocking. The unlock path is will unconditionally
re-enable interrupts in cases where irq state should be preserved. The
re-enablement allowed the other paths to execute which then causes the
deadlock.
Fix by converting the lock/unlock to irqsave/irqrestore.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In tests with remote ports contantly logging out/logging coupled with
occassional local link bounce, if a remote port is disocnnected for longer
than devloss_tmo and then subsequently reconnected, eventually the test
will fail to login with the remote port and remote port connectivity is
lost.
When devloss_tmo expires, the driver does not free the node struct until
the port or npiv instances is being deleted. The node is left allocated but
the state set to UNUSED. If the node was in the process of logging in when
the local link drop occurred, meaning the RPI was allocated for the node in
order to send the ELS, but not yet registered which comes after successful
login, the node is moved to the NPR state, and if devloss expires, to
UNUSED state. If the remote port comes back, the node associated with it
is restarted and this path happens to allocate a new RPI and overwrites the
prior RPI value. In the cases where the port was logged in and loggs out,
the path did release the RPI but did not set the node rpi value. In the
cases where the remote port never finished logging in, the path never did
the call to release the rpi. In this latter case, when the node is
subsequently restore, the new rpi allocation overwrites the rpi that was
not released, and the rpi is now leaked. Eventually the port will run out
of RPI resources to log into new remote ports.
Fix by following changes:
- When an rpi is released, do so under locks and ensure the node rpi value
is set to a non-allocated value (LPFC_RPI_ALLOC_ERROR). Note:
refactored to a small service routine to avoid indentation issues.
- When re-enabling a node, check the rpi value to determine if a new
allocation is necessary. If already set, use the prior rpi.
Enhanced logging to help in the future.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When connected to a high number of remote ports, the driver is encountering
PLOGI errors. The errors are due to adapter detected failures indicating
illegal field values.
Turns out the driver was prematurely clearing an RPI bitmask before waiting
for an UNREG_RPI mailbox completion. This allowed the RPI to be reused
before it was actually available.
Fix by clearing RPI bitmask only after UNREG_RPI mailbox completion.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
As spin_unlock_irq will enable interrupts.
Function lpfc_findnode_rpi is called from
lpfc_sli_abts_err_handler (./drivers/scsi/lpfc/lpfc_sli.c)
<- lpfc_sli_async_event_handler
<- lpfc_sli_process_unsol_iocb
<- lpfc_sli_handle_fast_ring_event
<- lpfc_sli_fp_intr_handler
<- lpfc_sli_intr_handler
and lpfc_sli_intr_handler is an interrupt handler.
Interrupts are enabled in interrupt handler. Use
spin_lock_irqsave/spin_unlock_irqrestore instead of spin_(un)lock_irq in
IRQ context to avoid this.
Signed-off-by: Fuqian Huang <huangfq.daxian@gmail.com>
Reviewed-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch adds general RSCN support:
- The ability to transmit an RSCN to the port on the other end of
the link (regular port if pt2pt, or fabric controller if fabric).
- And general recognition of an RSCN ELS when an ELS is received.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Arun Easi <aeasi@marvell.com>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Currently the FC-NVMe driver is leverating the SCSI FC transport class to
access the remote ports. Which means that all FC-NVMe remote ports will be
visible to the fc transport layer, but due to missing definitions the port
roles will always be 'unknown'. This patch adds the missing definitions to
the fc transport class to that the port roles are correctly displayed.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Reviewed-by: Giridhar Malavali <gmalavali@marvell.com>
Reviewed-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch avoids that the compiler warns about missing fall-through
annotation when building with W=1.
Cc: James Smart <james.smart@broadcom.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Acked-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If all the trunk links drop and a single link resumes, the link_state is
not properly reported. When trunked, the driver receives two async
cqes. One acqe reports the trunk link states, which the driver records.
The other cqe reports the overall state of the trunk. In the failing case,
the trunk link state acqe preceeds the overall trunk link state acqe. The
trunk link state acqe, as it's an "up" transition, calls a code path which
ensures a down transition before moving to the up state. The down
transition had a side effect of clearing the just-saved trunk link states.
Fix by not clearing the trunk link states if we've already transitioned
to a down state.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
During debug, it was seen that the driver is issuing commands specific to
SLI3 on SLI4 devices. Although the adapter correctly rejected the command,
this should not be done.
Revise the code to stop sending these commands on a SLI4 adapter.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When unloading the driver, mailbox commands may be sent without holding a
reference on the ndlp. By the time the mailbox command completes, the ndlp
may have reduced its ref counts and been freed. The problem was reported
by KASAN.
While unregistering due to driver unload, have the completion noop'd by
setting the ndlp context NULL'd. Due to the unload, no further action was
necessary. Also, while reviewing this path, the generic nulling of the
context after handling should be slightly moved.
Reported by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
For files modified as part of 12.2.0.0 patches, update copyright to 2019
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The conversion to enable SCSI and NVME fc4 support ran into an issue with
NPIV support. With NVME, NPIV is not currently supported, but with SCSI it
was. The driver reverted to its lowest setting meaning NPIV with SCSI was
not allowed.
Convert the NPIV checks and implementation so that SCSI can continue to
allow NPIV support.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Both NVME and SCSI aborts are now processed off the CQ workqueue and do not
generate events for the slowpath any more.
Remove the unused event code.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When a target's link dropped, an RSCN was received to communicate the
change. The driver detected the loss of the target and issued and UNREG_RPI
mailbox command. While that was being processed, another RSCN was received
to communicate the port coming back. The driver deferred the PLOGI to the
port until the mailbox command finishes. When the mailbox command completed
it saw the pending port and called the routines to issue the
PLOGI. However, it forgot to clear the UNREG_INP state flag, so the PLOGI
xmt routine nooped the PLOGI request assuming it needed to wait for the
mailbox command. At this point, login would never be re-attempted.
Clear UNREG_INP before issuing the deferred PLOGI.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If the adapter is taken offline, the trunk link port attributes continue to
report trunk links as up even though all links are down as the adapter is
offline.
Clear the trunk links state as part of taking the adapter offline.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Addition of support for if_type=6 missed several checks for interface type,
resulting in the failure of several key management features such as
firmware dump and loopback testing.
Correct the checks on the if_type so that both SLI4 IF_TYPE's 2 and 6 are
supported.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The current discovery state machine the driver treated FLOGI oddly. When
point to point, an FLOGI is to be exchanged by the two ports, with the port
with the most significant WWN then proceeding with PLOGI. The
implementation in the driver was keyed to closely with "what have I sent",
not with what has happened between the two endpoints. Thus, it blatantly
would ACC an FLOGI, but reject PLOGI's until it had its FLOGI ACC'd. The
problem is - the sending of FLOGI may be delayed for some reason, or the
response to FLOGI held off by the other side. In the failing situation the
other side sent an FLOGI, which was ACC'd, then sent PLOGIs which were then
rjt'd until the retry count for the PLOGIs were exceeded and the port gave
up. The FLOGI may have been very late in transmit, or the response held off
until the PLOGIs failed. Given the other port had the higher WWN, no PLOGIs
would occur and communication stopped.
Correct the situation by changing the FLOGI handling. Defer any response to
an FLOGI until the driver has sent its FLOGI as well. Then, upon either
completion of the sent FLOGI, or upon sending an ACC to a received FLOGI
(which may be received before or just after FLOGI was sent). the driver
will act on who has the higher WWN. if the other port does, the driver will
noop any handling of an FLOGI response (if outstanding) and wait for PLOGI.
If the local port does, the driver will transition to sending PLOGI and
will noop any action on responding to an FLOGI (if not yet received).
Fortunately, to implement this, it only took another state flag and
deferring any FLOGI response if the FLOGI has yet to be transmit. All
subsequent actions were already in place.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The driver is getting hit with 100s of RSCNs during remote port address
changes. Each of those RSCN's ends up generating UNREG_RPI and REG_PRI
mailbox commands. The discovery engine within the driver doesn't wait for
the mailbox command completions. Instead it sets state flags and moves
forward. At some point, there's a massive backlog of mailbox commands which
take time for the adapter to process. Additionally, it appears there were
duplicate events from the switch so the driver generated duplicate mailbox
commands for the same remote port. During this window, failures on PLOGI
and PRLI ELS's are see as the adapter is rejecting them as they are for
remote ports that still have pending mailbox commands.
Streamline the discovery engine so that PLOGI log checks for outstanding
UNREG_RPIs and defer the processing until the commands complete. This
better synchronizes the ELS transmission vs the RPI registrations.
Filter out multiple UNREG_RPIs being queued up for the same remote port.
Beef up log messages in this area.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The driver data structure for managing a mailbox command contained two
context fields. Unfortunately, the context were considered "generic" to be
used at the whim of the command code. Of course, one section of code used
fields this way, while another did it that way, and eventually there were
mixups.
Refactored the structure so that the generic contexts become a node context
and a buffer context and all code standardizes on their use.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add trunking support to the driver. Trunking is found on more recent
asics. In general, trunking appears as a single "port" to the driver
and overall behavior doesn't differ. Link speed is reported as an
aggregate value, while link speed control is done on a per-physical
link basis with all links in the trunk symmetrical. Some commands
returning port information are updated to additionally provide
trunking information. And new ACQEs are generated to report physical
link events relative to the trunk.
This patch contains the following modifications:
- Added link speed settings of 128GB and 256GB.
- Added handling of trunk-related ACQEs, mainly logging and trapping
of physical link statuses.
- Added additional bsg interface to query trunk state by applications.
- Augment link_state sysfs attribtute to display trunk link status
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The switches seem to respond faster to GID_PT vs GID_FT NameServer
queries. Add support for GID_PT to be used over GID_FT to enable
faster storage failover detection. Includes addition of new module
parameter to select between GID_PT and GID_FT (GID_FT is default).
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Testing a point-to-point topology and a case of re-FLOGI without
intervening link bouncing, showed an odd interaction with firmware and
a resulting scenario where the driver no longer probed after accepting
the new FLOGI.
Work around the firmware issue by issuing a link bounce if a FLOGI is
received after the link is already up and FLOGI's accepted.
While debugging the issue, realized that some debug traces should be
clarified to help in the future.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
On FCoE adapters, when running link bounce test in a loop, initiator
failed to login with switch switch and required driver reload to
recover. Switch reached a point where all subsequent FLOGIs would be
LS_RJT'd. Further testing showed the condition to be related to not
performing FCF discovery between FLOGI's.
Fix by monitoring FLOGI failures and once a repeated error is seen
repeat FCF discovery.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/scsi/lpfc/lpfc_hbadisc.c: In function 'lpfc_free_tx':
drivers/scsi/lpfc/lpfc_hbadisc.c:5431:19: warning:
variable 'psli' set but not used [-Wunused-but-set-variable]
Since commit 895427bd01 ("scsi: lpfc: NVME Initiator: Base modifications")
'psli' is not used any more.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When taking the board offline while performing i/o, unsafe locking errors
occurred and irq level isn't properly managed.
In lpfc_sli_hba_down, spin_lock_irqsave(&phba->hbalock, flags) does not
disable softirqs raised from timer expiry. It is possible that a softirq is
raised from the lpfc_els_retry_delay routine and recursively requests the same
phba->hbalock spinlock causing deadlock.
Address the deadlocks by creating a new port_list lock. The softirq behavior
can then be managed a level deeper into the calling sequences.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Driver only sends NVME PRLI to a device that also supports FCP. This resuls
in remote ports that don't have fc_remote_ports created for them. The driver
is clearing the nlp_fc4_type for a ndlp at the wrong time.
Fix by moving the nlp_fc4_type clearing to the discovery engine in the
DEVICE_RECOVERY state. Also ensure that rport registration is done for all
nlp_fc4_types.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Change references from "Broadcom Limited" to "Broadcom Inc." in the
copyright message. Update copyright duration if not yet updated for 2018.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
MDS diagnostics fail because of frame count mismatch.
Unavailability of SGL is the trigger for this issue. If ELS SGL is not
available to process MDS frame, IOCB is put in FCP txq but not attempted to
post afterwards. So, driver stops processing incoming frames as it runs out
of IOCB. lpfc_drain_txq attempts to submit IOCBS that are queued in ELS
txq but MDS frames are posted to FCP WQ.
Attempt to submit IOCBs that are present in FCP txq when MDS loopback is
running.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Remote port disappearance/reappearances would cause a series of RSCN
events to be delivered to the driver. During the resulting GID_FT
handling, the driver clears the fc4 settings on the remote port, which
makes it skip registration. As such, the nvme associations eventually
fail and return io errors to the applications.
Correct by not clearng the nlp_fc4_types for all nodes in
lpfc_issue_gidft. Instead, when the GID_FT response is handled, clear
the nlp_fc4_types of FCP and NVME prior to evaluating the fc4_type
returned by the GID_FT response. This approach leaves "skipped" nodes
with their nlp_fc4_types intacted.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When a port is configured for NVME and SCSI Initiator support and it probes
a target supporting both SCSI and NVME, NVME devices are discovered, but
SCSI devices are not.
The nlp_fc4_type for all NPorts should be cleared on Link Up or just before
GID_FTs get issued, as opposed to just during GID_FT cmpl. RSCN activity as
well as Link Up can trigger GID_FT. One GID_FT may complete before the next
one is issued.
Fix by clearng nlp_fc4_type on link up and just before both GID_FTs are
issued. During port swapping, copy nlp_fc4_type to the new ndlp
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The G7 adapter supports 64G link speeds. Add support to the driver.
In addition, a small cleanup to replace the odd bitmap logic with
a switch case.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Updated Copyright in files updated 11.4.0.7
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
During link bounce testing in a point-to-point topology, the host may
enter a soft lockup on the lpfc_worker thread:
Call Trace:
lpfc_work_done+0x1f3/0x1390 [lpfc]
lpfc_do_work+0x16f/0x180 [lpfc]
kthread+0xc7/0xe0
ret_from_fork+0x3f/0x70
The driver was simultaneously setting a combination of flags that caused
lpfc_do_work()to effectively spin between slow path work and new event
data, causing the lockup.
Ensure in the typical wq completions, that new event data flags are set
if the slow path flag is running. The slow path will eventually
reschedule the wq handling.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The driver currently registers any remote port that has NVME support.
It should only be registering target ports.
Register only target ports.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
During RSCN storms, the driver does not rediscover some targets. The
driver marks some RSCN as to be handled after the ones it's working
on. The driver missed processing some deferred RSCN.
Move where the driver checks for deferred RSCNs and initiate deferred
RSCN handling if the flag was set. Also revise nport state within the
RSCN confirm routine. Add some state data to a possible debug print to
aid future debugging.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
XRI_ABORTED_CQE completions were not being handled in the fast path.
They were being queued and deferred to the lpfc worker thread for
processing. This is an artifact of the driver design prior to moving
queue processing out of the isr and into a workq element. Now that queue
processing is already in a deferred context, remove this artifact and
process them directly.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This is mostly updates of the usual suspects: lpfc, qla2xxx, hisi_sas,
megaraid_sas, pm80xx, mpt3sas, be2iscsi, hpsa. and a host of minor
updates.
There's no major behaviour change or additions to the core in all of
this, so the potential for regressions should be small (biggest
potential being in the scsi error handler changes).
Signed-off-by: James E.J. Bottomley <jejb@linux.vnet.ibm.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=3O85
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"This is mostly updates of the usual suspects: lpfc, qla2xxx, hisi_sas,
megaraid_sas, pm80xx, mpt3sas, be2iscsi, hpsa. and a host of minor
updates.
There's no major behaviour change or additions to the core in all of
this, so the potential for regressions should be small (biggest
potential being in the scsi error handler changes)"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (203 commits)
scsi: lpfc: Fix hard lock up NMI in els timeout handling.
scsi: mpt3sas: remove a stray KERN_INFO
scsi: mpt3sas: cleanup _scsih_pcie_enumeration_event()
scsi: aacraid: use timespec64 instead of timeval
scsi: scsi_transport_fc: add 64GBIT and 128GBIT port speed definitions
scsi: qla2xxx: Suppress a kernel complaint in qla_init_base_qpair()
scsi: mpt3sas: fix dma_addr_t casts
scsi: be2iscsi: Use kasprintf
scsi: storvsc: Avoid excessive host scan on controller change
scsi: lpfc: fix kzalloc-simple.cocci warnings
scsi: mpt3sas: Update mpt3sas driver version.
scsi: mpt3sas: Fix sparse warnings
scsi: mpt3sas: Fix nvme drives checking for tlr.
scsi: mpt3sas: NVMe drive support for BTDHMAPPING ioctl command and log info
scsi: mpt3sas: Add-Task-management-debug-info-for-NVMe-drives.
scsi: mpt3sas: scan and add nvme device after controller reset
scsi: mpt3sas: Set NVMe device queue depth as 128
scsi: mpt3sas: Handle NVMe PCIe device related events generated from firmware.
scsi: mpt3sas: API's to remove nvme drive from sml
scsi: mpt3sas: API 's to support NVMe drive addition to SML
...
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly.
Cc: James Smart <james.smart@broadcom.com>
Cc: Dick Kennedy <dick.kennedy@broadcom.com>
Cc: "James E.J. Bottomley" <jejb@linux.vnet.ibm.com>
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>
Cc: linux-scsi@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Local Reject/Invalid RPI errors seen during discovery.
Temporary RPI cleanup was occurring regardless of SLI rev. It's only
necessary on SLI-4.
Adjust the test for whether cleanup is necessary.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The driver crashes when attempting to use a freed ndpl pointer.
The pci_remove_one handler runs on a separate kernel thread. The order
of the removal is starting by freeing all of the ndlps and then
disabling interrupts. In between these two events the driver can still
receive an ELS and process it. When it tries to use the ndlp pointer
will be NULL
Change the order of the pci_remove_one vs disable interrupts so that
interrupts are disabled before the ndlp's are freed.
Cc: <stable@vger.kernel.org> # 4.12+
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add Buffer to buffer credit recovery support to the driver. This is a
negotiated feature with the peer that allows for both sides to detect
dropped RRDY's and FC Frames and recover credit.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In a server with an 8G adapter and a 32G adapter, running NVME and FCP,
the server would crash with the following stack.
RIP: 0010: ... lpfc_nvme_register_port+0x38/0x420 [lpfc]
lpfc_nlp_state_cleanup+0x154/0x4f0 [lpfc]
lpfc_nlp_set_state+0x9d/0x1a0 [lpfc]
lpfc_cmpl_prli_prli_issue+0x35f/0x440 [lpfc]
lpfc_disc_state_machine+0x78/0x1c0 [lpfc]
lpfc_cmpl_els_prli+0x17c/0x1f0 [lpfc]
lpfc_sli_sp_handle_rspiocb+0x39b/0x6b0 [lpfc]
lpfc_sli_handle_slow_ring_event_s3+0x134/0x2d0 [lpfc]
lpfc_work_done+0x8ac/0x13b0 [lpfc]
lpfc_do_work+0xf1/0x1b0 [lpfc]
Crash, on the 8G adapter, is due to a vport which does not have a nvme
local port structure. It's not supposed to have one. NVME is not
supported on the 8G adapter, so the NVME PRLI, which started this flow
shouldn't have been sent in the first place.
Correct discovery engine to recognize when on an SLI3 rport, which
doesn't support SLI3, if the rport supports only NVME, don't send a NVME
PRLI. Instead, as no FC4 will be used, a LOGO is sent. If rport is FCP
and NVME, only execute the SCSI PRLI.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When unloading the driver, the NVMET driver would wait the full 30
seconds for its UNMAPPED initiator node to get removed before continuing
with the unload process. NVMEI worked correctly.
For each rport put into UNMAPPED or MAPPED state by NVMET, the driver
puts a reference on the NDLP. The difference is that NVMEI has a
unregister call for its rports and the extra reference is removed in the
unregister process. For NVMET, the driver has to remove the reference
explicitly when dropping out of UNMAPPED or MAPPED because there is no
unregister call.
Add a call to lpfc_nlp_put on the ndlp when NVMET and the old state was
UNMAPPED or MAPPED.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Lun Priority level shown as NA
Remote port is not getting registered for nameserver and fdmi. Due to
which dfc SendCTPassThru cmd is failing.
Made changes to register the remote port for both.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Jianping Liu