Relocate the codes related to dma_map/unmap in hisi_sas_task_prep() to
reduce complexity, with a view to add DIF/DIX support.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patchset fixes some warnings detected by the sparse tool, like these:
drivers/scsi/hisi_sas/hisi_sas_main.c:1469:52: warning: incorrect type in assignment (different base types)
drivers/scsi/hisi_sas/hisi_sas_main.c:1469:52: expected unsigned short [unsigned] [assigned] [usertype] tag_of_task_to_be_managed
drivers/scsi/hisi_sas/hisi_sas_main.c:1469:52: got restricted __le16 [usertype] <noident>
drivers/scsi/hisi_sas/hisi_sas_main.c:1723:52: warning: incorrect type in assignment (different base types)
drivers/scsi/hisi_sas/hisi_sas_main.c:1723:52: expected unsigned short [unsigned] [assigned] [usertype] tag_of_task_to_be_managed
drivers/scsi/hisi_sas/hisi_sas_main.c:1723:52: got restricted __le16 [usertype] <noident>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently the time of SAS SSP connection is 1ms, which means the link
connection will fail if no IO response after this period.
For some disks handling large IO (such as 512k), 1ms is not enough, so
change it to 5ms.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In function hisi_sas_task_prep(), we check asd_sas_port, but in function
hisi_sas_task_exec(), we already refer to asd_sas_port by using function
dev_to_hisi_hba() implicitly. So to avoid this possible invalid
dereference, relocate the check to function hisi_sas_task_prep().
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If INT_COAL_EN is enabled, configure time and count of interrupt
coalescing. Then if CQ collects count of CQ entries in time, it will
report the interrupt. Or if CQ doesn't collect enough CQ entries in time,
it will report the interrupt at timeout.
As all the registers are not supported to be changed dynamically, we need
to config those register between disable and enable PHYs.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If CQ_INT_CONVERGE_EN is enabled, the interrupts of all the 16 CQ queues
will be reported by CQ0.
So we need to change the process of CQ tasklet for this situation.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently all the three HBA (v1/v2/v3 HW) share the same host attributes.
To support each HBA having separate attributes in future, create per-HBA
attributes.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The driver currently uses pci_set_dma_mask despite otherwise using the
generic DMA API. Switch it over to the better generic DMA API.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/scsi/hisi_sas/hisi_sas_v1_hw.c: In function 'start_delivery_v1_hw':
drivers/scsi/hisi_sas/hisi_sas_v1_hw.c:907:20: warning:
variable 'dq_list' set but not used [-Wunused-but-set-variable]
drivers/scsi/hisi_sas/hisi_sas_v2_hw.c: In function 'start_delivery_v2_hw':
drivers/scsi/hisi_sas/hisi_sas_v2_hw.c:1671:20: warning:
variable 'dq_list' set but not used [-Wunused-but-set-variable]
drivers/scsi/hisi_sas/hisi_sas_v3_hw.c: In function 'start_delivery_v3_hw':
drivers/scsi/hisi_sas/hisi_sas_v3_hw.c:889:20: warning:
variable 'dq_list' set but not used [-Wunused-but-set-variable]
It never used since introduction in commit
fa222db0b0 ("scsi: hisi_sas: Don't lock DQ for complete task sending")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
There is a NULL pointer dereference in case *slot* happens to be NULL at
lines 1053 and 1878:
struct hisi_sas_cq *cq =
&hisi_hba->cq[slot->dlvry_queue];
Notice that *slot* is being NULL checked at lines 1057 and 1881:
if (slot), which implies it may be NULL.
Fix this by placing the declaration and definition of variable cq, which
contains the pointer dereference slot->dlvry_queue, after slot has been
properly NULL checked.
Addresses-Coverity-ID: 1474515 ("Dereference before null check")
Addresses-Coverity-ID: 1474520 ("Dereference before null check")
Fixes: 584f53fe5f ("scsi: hisi_sas: Fix the race between IO completion and timeout for SMP/internal IO")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Reviewed-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently a spin_unlock_irqrestore() call is missing on the error path,
so add it.
Reported-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Update registers as follows:
- Default value of AIP timer is 1ms, and it is easy for some expanders to
cause IO error. Change the value to max value 65ms to avoid IO error for
those expanders.
- A CQ completion will be reported by HW when 4 CQs have occurred or the
aging timer expires, whichever happens first. Sor serial IO scenario, it
will still wait 8us for every IO before it is reported. So in the
situation, the performance is poor. So to improve it, change the limit
time to the least value.
For other scenario, it does little affect to the performance.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently we use the IPTT defined in LLDD to identify IOs. Actually for
IOs which are from the block layer, they have tags to identify them. So
for those IOs, use tag of the block layer directly, and for IOs which is
not from the block layer (such as internal IOs from libsas/LLDD), reserve
96 IPTTs for them.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The interrupts of ent72 and ent74 are not processed by PCIe AER handling,
so we need to unmask the interrupts and process them first in the driver.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If an SSP/SMP IO times out, it may be actually in reality be
simultaneously processing completion of the slot in
slot_complete_vx_hw().
Then if the slot is freed in slot_complete_vx_hw() (this IPTT is freed
and it may be re-used by other slot), and we may abort the wrong slot in
hisi_sas_abort_task().
So to solve the issue, free the slot after the check of
SAS_TASK_STATE_ABORTED in slot_complete_vx_hw().
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If SMP/internal IO times out, we will possibly free the task immediately.
However if the IO actually completes at the same time, the IO completion
may refer to task which has been freed.
So to solve the issue, flush the tasklet to finish IO completion before
free'ing slot/task.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In evaluating hisi_hba, the sas_port may be NULL, so for safety relocate
the the check to value possible NULL deference.
Signed-off-by: Luo Jiaxing <luojiaxing@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
At directly attached situation, if the user modifies the sysfs interface
of maximum_linkrate and minimum_linkrate to renegotiate the linkrate
between SAS controller and target, the value of both files mentioned
above should have change to user setting after renegotiate is over, but
it remains unchanged.
To fix this bug, maximum_linkrate and minimum_linkrate will be directly
fed back to relevant sas_phy structure.
Signed-off-by: Luo Jiaxing <luojiaxing@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Now LLDDs have to implement lldd_port_deformed method otherwise NULL
dereference will happen. Make it optional and remove the dummy implementation
in hisi_sas.
Signed-off-by: Jason Yan <yanaijie@huawei.com>
CC: John Garry <john.garry@huawei.com>
CC: Johannes Thumshirn <jthumshirn@suse.de>
CC: Ewan Milne <emilne@redhat.com>
CC: Christoph Hellwig <hch@lst.de>
CC: Tomas Henzl <thenzl@redhat.com>
CC: Dan Williams <dan.j.williams@intel.com>
CC: Hannes Reinecke <hare@suse.com>
Acked-by: John Garry <john.garry@huawei.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add a check ERR bit of status to decide whether there is something wrong
with initial register-D2H FIS. If error exist, PHY link reset the channel
to restart OOB.
Directly call work HISI_PHYE_LINK_RESET replacing disable_phy_vx_hw() and
enable_phy_vx_hw().
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In task start delivery function, we need to add a memory barrier to prevent
re-ordering of reading memory by hardware. Because the slot data is set in
task prepare function and it could be running in another CPU.
This patch adds an memory barrier after s->ready is read in the task start
delivery function, and uses WRITE_ONCE() in the places where s->ready is
set to ensure that the compiler does not re-order.
Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
To decrease the usage of spinlock during delivery IO, relocate some code in
hisi_sas_task_prep().
Also an invalid comment is removed.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch implements handlers of PCIe FLR for v3 hw, reset_prepare() and
reset_done().
User can issue FLR through sysfs interface, as v3 hw support PCIe FLR.
Then if we don't implement these two handlers, our SAS controller will not
work after executing FLR.
Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Much code of PM suspend function also exists in soft reset function. This
is not concise. So, this patch relocates the common code of these two
functions to a separate function.
Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch tidies host controller reset function by putting some code to
two new functions, and exports these two functions out, so that they could
be used by FLR feature to be realised.
Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
There is an issue that link reset can't recover PHY when STP link timeout.
Because current process of enabling PHY for v3 hw will wait last
transmission done. The time of one transmission depends IO size, disk model
and so on. Normally, it should be shorter than 50ms. But the last
transmission could be never done for some abnormal scenarios, such as STP
link timeout.
This patch is to fix the issue. Check PHY status after starting process of
enabling PHY for 50ms. If the PHY is still active, we disable it forcibly
by PHY reset. Of course, we need to clear the PHY reset bit when enable
PHY.
Besides, the function disable_phy_v3_hw() should not be suitable to call in
interrupts for hilink bug for this 50ms delay. Then, we do link reset for
hilink bug directly. The change is that we don't clear the invalid dword
count register. This is better. Because we should not clear such error
count while not saved.
Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The ISR of channel interrupt of v3 hw is a little long and messy. This
patch tidies it by relocating CHL_INT1 and CHL_INT2 handling to new
function separately.
Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
For some time now we have not used hisi_sas_slot_abort() to handle erroring
slots, apart from in archaic v1 hw.
As such, remove this function and associated code. For v1 hw, move error
handling to same scheme as other hw revisions, where we allow erroring
commands to timeout.
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Update CFG_1US_TIMER_TRSH and CON_CFG_DRIVER settings.
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The init is missed for hisi_sas_phy spinlock, so add it.
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently the driver spends much time allocating and freeing the slot DMA
buffer for command delivery/completion. To boost the performance,
pre-allocate the buffers for all IPTT. The downside of this approach is
that we are reallocating all buffer memory upfront, so hog memory which we
may not need.
However, the current method - DMA buffer pool - also caches all buffers and
does not free them until the pool is destroyed, so is not exactly efficient
either.
On top of this, since the slot DMA buffer is slightly bigger than a 4K
page, we need to allocate 2x4K pages per buffer (for 4K page kernel), which
is quite wasteful. For 64K page size this is not such an issue.
So, for the 4K page case, in order to make memory usage more efficient,
pre-allocating larger blocks of DMA memory for the buffers can be more
efficient.
To make DMA memory usage most efficient, we would choose a single
contiguous DMA memory block, but this could use up all the DMA memory in
the system (when CMA enabled and no IOMMU), or we may just not be able to
allocate a DMA buffer large enough when no CMA or IOMMU.
To decide the block size we use the LCM (least common multiple) of the
buffer size and the page size. We roundup(64) to ensure the LCM is not too
large, even though a little memory may be wasted per block.
So, with this, the total memory requirement is about is about 17MB for 4096
max IPTT.
Previously (for 4K pages case), it would be 32MB (for all slots
allocated).
With this change, the relative increase of IOPS for bs=4K read when
PAGE_SIZE=4K and PAGE_SIZE=64K is as follows:
IODEPTH 4K PAGE_SIZE 64K PAGE_SIZE
32 56% 47%
64 53% 44%
128 64% 43%
256 67% 45%
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In host reset, we use TMF or soft-reset to re-init device, and if success,
we will release all LLDD resources of this device. If the init fails -
maybe because the device was removed or link has not come up - then do not
release the LLDD resources, but rather rely on SCSI EH to handle the
timeout for these resources later on.
But if clear nexus ha calls host reset, which is the last effort of SCSI
EH, we should release all LLDD remain resources. Because SCSI EH will
release all tasks after clear nexus ha.
Before release, we do I_T nexus reset to try to clear target remain IOs.
Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
During reset, we don't want PHY events reported to libsas for PHYs which
were previously attached prior to reset.
So check hisi_hba->flags for HISI_SAS_RESET_BIT to filter PHY events during
reset.
Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
After soft_reset() for host reset, we should not be allowed to send
commands to the HW before the PHYs have come up and the port ids have been
refreshed.
Prior to this point, any commands cannot be successfully completed.
This exclusion is achieved by grabbing the host reset semaphore.
Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
There is a possible conflict when a device is removed and host reset occurs
concurrently.
The reason is that then the device is notified as gone, we try to clear the
ITCT, which is notified via an interrupt. The dev gone function pends on
this event with a completion, which is completed when the ITCT interrupt
occurs.
But host reset will disable all interrupts, the wait_for_completion() may
wait indefinitely.
This patch adds an semaphore to synchronise this two processes. The
semaphore is taken by the host reset as the basis of synchronising.
Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
There are many BROADCAST primitives generated by the host. We are only
interested in BROADCAST (CHANGE) primitives currently, so only process
this.
We have applied this processing for v2 hw before, and it is also needed for
v3 hw.
Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch replaces the usage of dma_alloc_coherent() with the managed
version, dmam_alloc_coherent(), hereby reducing replicated code.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by; John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When issuing a nexus reset for directly attached device, we want to ignore
the PHY down events so libsas will not deform and reform the port.
In the case that the attached SAS changes for the reset, libsas will deform
and form a port.
For scenario that the PHY does not come up after a timeout period, then
report the PHY down to libsas.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
It is an step of executing task to get free slot. If the step fails, we
will cleanup LLDD resources and should return failure to upper layer or
internal caller to abort task execution of this time.
But in the current code, the caller of get_free_slot() doesn't return
failure when get_free_slot() failed. This patch is to fix it.
Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
For v2 hw, STP link from target is rejected after host reset because of a
SoC bug. The STP reject will be terminated after we have sent IO from each
PHY of a port.
This is not an problem before, as we don't need to setup STP link from
target immediately after host reset. But now, it is. Because we want to
send soft-reset immediately after host reset.
In order to terminate STP reject quickly, this patch send ATA reset command
through each PHY of a port. Notes: ATA reset command don't need target's
response.
Besides, we do abort dev for each device before terminating STP reject.
This is a quirk of v2 hw.
Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch adds a force PHY function for internal ATA command for v2 hw.
Because there is an SoC bug in v2 hw, and need send an IO through each PHY
of a port to work around a bug which occurs after a controller reset.
This force PHY function will be used in the later patch.
Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In future scenarios we will want to use the TMF struct for more task types
than SSP.
As such, we can add struct hisi_sas_tmf_task directly into struct
hisi_sas_slot, and this will mean we can remove the TMF parameters from the
task prep functions.
Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
We may reset the controller in many scenarios, such as SCSI EH and HW
errors. There should be no IO which returns from target when SCSI EH is
active. But for other scenarios, there may be. It is not necessary to make
such IOs fail.
This patch adds an function of trying to wait for any commands, or IO, to
complete before host reset. If no more CQ returned from host controller in
100ms, we assume no more IO can return, and then stop waiting. We wait 5s
at most.
The HW has a register CQE_SEND_CNT to indicate the total number of CQs that
has been reported to driver. We can use this register and it is reliable to
resd this register in such scenarios that require host reset.
Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
After the controller is reset, it is possible that the disks attached still
have outstanding IO to complete.
Thus, when the PHYs come back up after controller reset, it is possible
that these IOs complete at some unknown point later.
We want to ensure that all IOs are complete after the controller reset so
that all associated IPTT and other resources can be recycled safely.
To achieve this, re-init the disks by TMF or softreset (in case of ATA
devices).
If the init fails - maybe because the device was removed or link has not
come up - then do not release the device resources, but rather rely on SCSI
EH to handle the timeout for these resources later on.
This patch also does some cleanup to hisi_sas_init_disk(), including
removing superfluous cases in the switch statement.
Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When a SCSI host is registered, the SCSI mid-layer takes a reference to a
module in Scsi_host.hostt.module. In doing this, we are prevented from
removing the driver module for the host in dangerous scenario, like when a
disk is mounted.
Currently there is only one scsi_host_template (sht) for all HW versions,
and this is the main.c module. So this means that we can possibly remove
the HW module in this dangerous scenario, as SCSI mid-layer is only
referencing the main.c module.
To fix this, create a sht per module, referencing that same module to
create the Scsi host.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When a disk is discovered, it may be in an error state, or there may be
residual commands remaining in the disk.
To ensure any disk is in good state after discovery, reset via TMF (for SAS
disk) or softreset (for a SATA disk).
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch implements LED feature of directly attached disk for v3 hw.
In fact, this hw has created an SGPIO component for LED feature, and we can
control LEDs just by internal registers.
Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
To reduce possibility of hitting unknown SoC bugs and aid debugging and
test, change allocation mode of device id from last used device id instead
of lowest available index.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently we find the lowest available empty bit in the IPTT bitmap to
allocate the IPTT for a command.
To reduce possibility of hitting unknown SoC bugs and also aid in the
debugging of those same bugs, change the allocation mode.
The next allocation method is to use the next free slot adjacent to the
most recently allocated slot, in a round-robin fashion.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
There is much common code and functionality between the HW versions to set
the PHY linkrate.
As such, this patch factors out the common code into a generic function
hisi_sas_phy_set_linkrate().
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently we don't check that device is not gone before dereferencing
its elements in the function hisi_sas_task_exec() (specifically, the DQ
pointer).
This patch fixes this issue by filling in the DQ pointer in
hisi_sas_task_prep() after we check that the device pointer is still
safe to reference.
[mkp: typo]
Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The IPTT of a slot is unique, and we currently use hisi_hba lock to
protect it.
Now slot is managed on hisi_sas_device.list, so use DQ lock to protect
for allocating and freeing the slot.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently we lock the DQ to protect whole delivery process. So this
stops us building slots for the same queue in parallel, and can affect
performance.
To optimise it, only lock the DQ during special periods, specifically
when allocating a slot from the DQ and when delivering a slot to the HW.
This approach is now safe, thanks to the previous patches to ensure that
we always deliver a slot to the HW once allocated.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently we allocate the slot's memory buffer after allocating the DQ
slot.
To aid DQ lockout reduction, and allow slots to be built in parallel,
move this step (which can fail) prior to allocating the slot.
Also a stray spin_unlock_irqrestore() is removed from internal task exec
function.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Since the task prep functions now should not fail, adjust the return
types to void.
In addition, some checks in the task prep functions are relocated to the
main module; this is specifically the check for the number of elements
in an sg list exceeded the HW SGE limit.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently we use DQ lock to protect delivery of DQ entry one by one.
To optimise to allow more than one slot to be built for a single DQ in
parallel, we need to remove the DQ lock when preparing slots, prior to
delivery.
To achieve this, we rearrange the slot build order to ensure that once
we allocate a slot for a task, we do cannot fail to deliver the task.
In this patch, we rearrange the slot building for SMP tasks to ensure
that sg mapping part (which can fail) happens before we allocate the
slot in the DQ.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
There is an SoC bug of v3 hw development version. When hot- unplugging a
directly attached disk, the PHY down interrupt may not happen. It is
very easy to appear on some boards.
When this issue occurs, the controller will receive many invalid dword
frames, and the "alos" fields of register HILINK_ERR_DFX can indicate
that disk was unplugged.
As an workaround solution, this patch detects this issue in the channel
interrupt, and workaround it by following steps:
- Disable the PHY
- Clear error code and interrupt
- Enable the PHY
Then the HW will reissue PHY down interrupt.
Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
It is common to use readl poll timeout helpers in the driver, so create
custom wrappers.
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Event95 is used for DFX purpose. The relevant bit for this interrupt in
the ENT_INT_SRC_MSK3 register has been disabled, so remove the
processing.
Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
As a unconstrained command, a command can be sent to SATA disk even if
SATA disk status is BUSY, ERR or DRQ.
If an ATA reset assert is successful but ATA reset de-assert fails, then
it will retry the reset de-assert. If reset de- assert retry is
successful, we think it is okay to probe the device but actually it
still has Err status.
Apparently we need to retry the ATA reset assertion and de- assertion
instead for this mentioned scenario.
As such, we config ATA reset assert as a constrained command, if ATA
reset de-assert fails, then ATA reset de-assert retry will also
fail. Then we will retry the proper process of ATA reset assert and
de-assert again.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
After the controller is reset, we currently may not honour the PHY max
linkrate set via sysfs, in that after a reset we always revert to max
linkrate of 12Gbps, ignoring the value set via sysfs.
This patch modifies to policy to set the programmed PHY linkrate,
honouring the max linkrate programmed via sysfs.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
We should only have the timer enabled after PHY up after controller
reset, so disable prior to reset.
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
It is possible to dereference a NULL-pointer in hisi_sas_abort_task() in
special scenario when the device has been removed.
If an SMP task times-out, it will call hisi_sas_abort_task() to
recover. And currently there is a check in hisi_sas_abort_task() to
avoid the situation of processing the abort for the removed device.
However we have an ordering problem, in that we may reference a task for
the removed device before checking if the device has been removed.
Fix this by only referencing the sas_dev after we know it is still
present.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
There are 28 bytes of protection information record of SSP for v3 hw, 16
bytes for v2 hw, and probably 24 for v1 hw (forgotten now).
So use a value big enough in hisi_sas_command_table_ssp.prot to cover
all cases.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When the host is frozen in SCSI EH state, at any point after the LLDD
sets SAS_TASK_STATE_DONE for the sas_task task state, libsas may free
the task; see sas_scsi_find_task().
This puts the LLDD in a difficult position, in that once it sets
SAS_TASK_STATE_DONE for the task state it should not reference the
sas_task again. But the LLDD needs will check the sas_task indirectly in
calling task->task_done()->sas_scsi_task_done() or sas_ata_task_done()
(to check if the host is frozen state actually).
And the LLDD cannot set SAS_TASK_STATE_DONE for the task state after
task->task_done() is called (as the sas_task is free'd at this point).
This situation would seem to be a problem made by libsas.
To work around, check in the LLDD whether the host is in frozen state to
ensure it is ok to call task->task_done() function. If in the frozen
state, we rely on SCSI EH and libsas to free the sas_task directly.
We do not do this for the following IO types:
- SMP - they are managed in libsas directly, outside SCSI EH
- Any internally originated IO, for similar reason
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If the SCSI host enters EH, any pending IO will be processed by SCSI
EH. However it is possible that SCSI EH will try to abort the IO and
also at the same time the IO completes in the driver. In this situation
there is a small chance of freeing the sas_task twice.
Then if another IO re-uses freed sas_task before the second time of
free'ing sas_task, it is possible to free incorrect sas_task.
To avoid this situation, add some checks to increase reliability. The
sas_task task state flag SAS_TASK_STATE_ABORTED is used to mutually
protect the LLDD and libsas freeing the task.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In the DQ tasklet processing it is not necessary to take the DQ lock, as
there is no contention between adding slots to the CQ and removing slots
from the matching DQ.
In addition, since we run each DQ in a separate tasklet context, there
would be no possible contention between DQ processing running for the
same queue in parallel.
It is still necessary to take hisi_hba lock when free'ing slots.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch removes unneeded structure elements:
- hisi_sas_phy.dev_sas_addr: only ever written
- Also remove associated function which writes it,
hisi_sas_init_add().
- hisi_sas_device.attached_phy: only ever written
- Also remove code to set it in hisi_sas_dev_found()
Signed-off-by: John Garry <john.garry@huawei.com>
Reviewed-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When we find an erroneous slot completion, to help aid debugging add the
device index to the current debug log.
Signed-off-by: John Garry <john.garry@huawei.com>
Reviewed-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
There is a bug of v3 hw development version. When AXI error happen, hw
may return an abnormal CQ that IPTT value is 0xffff. This will cause
IPTT out-of-bounds reference.
This patch adds a check of IPTT in cq_tasklet_v3_hw() and discards
invalid slot. This workaround scheme is just to enhance fault-tolerance
of the driver. So, we will apply this scheme for all version of v3 hw,
although release version has fixed this SoC bug.
Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently we check the fis->command value in 2 locations in
hisi_sas_get_ata_protocol() switch statement. Fix this by consolidating
the check for fis->command value to 1 location only.
Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This is a warning coming from Coccinelle, and need to use new interface
dma_zalloc_coherent() instead of dma_alloc_coherent()/memset().
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Delete timer for v1 and v3 hw when removing hisi_sas driver.
Signed-off-by: Xiang chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
There is an modification for later revision of v3 hw. More HW errors are
reported through RAS interrupt. These errors were originally reported
only through MSI.
When report to RAS, some combinations are done to port AXI errors and
FIFO OMIT errors. For example, each port has 4 AXI errors, and they are
combined to one when report to RAS.
This patch does two things:
1. Enable RAS interrupt of these errors and handle them in PCI
error handlers.
2. Disable MSI interrupts of these errors for this later revision hw.
Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When directly connected with SATA disks in different SAS cores, fill SAS
address with scsi_host's id to make it's fake SAS address unique.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Remove dependencies on HAS_DMA where a Kconfig symbol depends on another
symbol that implies HAS_DMA, and, optionally, on "|| COMPILE_TEST". In
most cases this other symbol is an architecture or platform specific
symbol, or PCI.
Generic symbols and drivers without platform dependencies keep their
dependencies on HAS_DMA, to prevent compiling subsystems or drivers that
cannot work anyway.
This simplifies the dependencies, and allows to improve compile-testing.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Reviewed-by: Mark Brown <broonie@kernel.org>
Acked-by: Robin Murphy <robin.murphy@arm.com>
Acked-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Export device table of v3 hw to userspace, or auto probe will fail for v3
hw.
Also change the module alias to include "pci", instead of "platform".
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Do some modifications for register configuring for hip08.
In future, to reduce kernel churn with patches to modify registers, any
registers which may change between board models (mostly PHY/SERDES related)
should be set in ACPI reset handler.
Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com>
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The patch does some code cleanup and fixes some small bugs:
- Correct return status of phy_up_v3_hw() and phy_bcast_v3_hw()
- Add static for function phy_get_max_linkrate_v3_hw()
- Change exception return status when no reset method
- Change magic value to ts->stat in slot_complete_vx_hw()
- Remove unnecessary check for dev_is_sata()
- Fix some issues of alignment and indents (Authored by Xiaofei Tan in
another patch, but added here to be practical)
Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com>
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
It is an implicit regulation that error code that function returned should
be negative. But hisi_sas_task_prep() doesn't follow this. This may cause
problems in the upper layer code.
For example, in sas_expander.c of libsas, smp_execute_task_sg() may return
the number of bytes of underrun. It will be conflicted with the scenaio
lldd_execute_task() return an positive error code.
This patch change the return value from SAS_PHY_DOWN to -ECOMM in
hisi_sas_task_prep().
Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The structure element hisi_sas_devices.running_req to count how many
commands are active is in effect only ever written in the code, so remove
it.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The current 110ms expiry time is not long enough for the internal abort
task.
The reason is that the internal abort task could be blocked in HW if the HW
is retrying to set up link. The internal abort task will be executed only
when the retry process finished.
The maximum time is 5s for the retry of setting up link. So, the timer
expire should be more than 5s. This patch increases it from 110ms to 6s.
Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
It is not right to set the register PROG_PHY_LINK_RATE while PHY is still
enabled. So if we want to change PHY linkrate, we need to disable PHY before
setting the register PROG_PHY_LINK_RATE, and then start-up PHY. This patch
is to fix this issue.
Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In sysfs, there are two files about minimum linkrate, and also two files for
maximum linkrate. Take maximum linkrate example, maximum_linkrate_hw is
read-only and indicated by the register HARD_PHY_LINKRATE, and
maximum_linkrate is read-write and corresponding to the register
PROG_PHY_LINK_RATE.
But in the function phy_up_v*_hw(), we get *_linkrate value from
HARD_PHY_LINKRATE. It is not right. This patch is to fix this issue.
Unreferenced PHY-interrupt enum is also removed for v3 hw.
Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The register SAS_PHY_CTRL is configured according to signal quality. The
signal quality is calculated by signal attenuation of hardware physical
link. It may be different for different PCB layout.
So, in order to give better support to new board, this patch add support to
reading the devicetree property, "hisilicon,signal-attenuation". Of course,
we still keep an default value in driver to adapt old board.
Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When device gone, NULL pointer can be accessed in free_device callback
if during SAS controller reset as we clear structure sas_dev prior.
Actually we can only set dev_type as SAS_PHY_UNUSED and not clear
structure sas_dev as all the members of structure sas_dev will be
re-initialized after device found.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch implements LED feature of directly attached disk for v2 hw.
As libsas has provided an interface lldd_write_gpio() for this feature,
we just need realise the interface following SPGIO API.
We use an CPLD to finish the hardware part of this feature, and the base
address of CPLD should be configured through ACPI or DT tables.
Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fixes the following sparse warning:
drivers/scsi/hisi_sas/hisi_sas_main.c:1691:25: warning:
symbol 'host_attrs' was not declared. Should it be static?
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
According to ATA protocol, SET MAX commands belong to different frame
types. So judge features field of SET MAX commands to decide which
frame type they belongs to.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add a sysfs attr that LLDD can configure it for every host. We made an
example in hisi_sas. Other LLDDs using libsas can implement it if they
want.
Suggested-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Jason Yan <yanaijie@huawei.com>
CC: John Garry <john.garry@huawei.com>
CC: Johannes Thumshirn <jthumshirn@suse.de>
CC: Ewan Milne <emilne@redhat.com>
CC: Christoph Hellwig <hch@lst.de>
CC: Tomas Henzl <thenzl@redhat.com>
CC: Dan Williams <dan.j.williams@intel.com>
Acked-by: John Garry <john.garry@huawei.com> #for hisi_sas part
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
For v3 hw SAS, it supports configuring power state from D0 to D3 for entering
Low Power status and power state from D3 to D0 for quit Low Power status.
When power state from D0 to D3, HW will send FLR to clear the registers of
ECAM and BAR space, and when power state from D3 to D0, it will clear the
registers of ECAM space only.
So when suspend, need to do like controller reset (including disable
interrupts/DQ/PHY/BUS), and also release slots after FLR. When resume,
re-config the registers of BAR space.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In function sas_suspend_devices(), it requires callback lldd_port_deformed
callback to be implemented if lldd_port_deformed is implemented.
So add a stub for lldd_port_deformed.
Callback lldd_port_deformed was not required as the port deformation is done
elsewhere in the LLDD.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch fix SAS_QUEUE_FULL problem. The test situation is close port while
running IO.
In sas_eh_handle_sas_errors(), SCSI EH will free sas_task of the device if
lldd_I_T_nexus_reset() return TMF_RESP_FUNC_COMPLETE or -ENODEV. But in our
SAS driver, we only free slots of the device when the return value is
TMF_RESP_FUNC_COMPLETE. So if the return value is -ENODEV, the slot resource
will not free any more.
As an solution, we should also free slots of the device in
lldd_I_T_nexus_reset() if the return value is -ENODEV.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
We should do internal abort dev before TMF_ABORT_TASK_SET and TMF_LU_RESET.
Because we may only have done internal abort for single IO in the earlier part
of SCSI EH process. Even the internal abort to the single IO, we also don't
know whether it is successful.
Besides, we should release slots of the device in hisi_sas_abort_task_set() if
the abort is successful.
Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Normally, hardware should ensure that internal abort timeout will never
happen. If happen, it would be an SoC failure. What's more, HW will not
process any other commands if an internal abort hasn't return CQ, and they
will time out also.
So, we should judge the result of internal abort in SCSI EH, if it is failed,
we should give up to do TMF/softreset and return failure to the upper layer
directly.
This patch do following things to achieve this:
1. When internal abort timeout happened, we set return value to -EIO in
hisi_sas_internal_task_abort().
2. If prep_abort() is not support, let hisi_sas_internal_task_abort() return
TMF_RESP_FUNC_FAILED.
3. If hisi_sas_internal_task_abort() return an negative number, it can be
thought that it not executed properly or internal abort timeout. Then we
won't do behind TMF or softreset, and return failure directly.
Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
We should do link reset of PHY when identify timeout or STP link timeout. They
are internal events of SOC and are notified to driver through interrupts of
CHL_INT2.
Besides, we should add an delay work to do link reset as it needs sleep. So,
this patch add an new PHY event HISI_PHYE_LINK_RESET for this.
Notes: v2 HW doesn't report the event of STP link timeout. So, we only need
to handle event of identify timeout for v2 HW.
Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Use an general way to do delay work for a PHY. Then it will be easier to add
new delayed work for a PHY in future.
Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add port AXI errors handling for v2 hw. We do host controller reset for such
errors.
Besides, change port muli-bits ECC error handling, and we should also do host
reset for such error. So, this patch put them in the same struct with port AXI
error.
Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Change code format of int_chnl_int_v2_hw() to be consistent with v3 hw to
reduce an tag indent.
Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add some print at some places such as error info and cq of exception IO,
device found etc, and also adjust some log levels.
All this to assist debugging ability.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
We use PCIe AER to support RAS feature for v3 hw. This driver should do
following two things to support this:
1. Enable RAS interrupts, so that errors can be reported to RAS module.
2. Realize err_handler for sas_v3_pci_driver. Then if non-fatal error is
detected, print error source and try to recover SAS controller.
Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
For v3 hw, each NCQ will return a CQ, so it is no need to acquire IPTT from
ITCT, just acquire it from IPTT field of CQ.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Sometimes it is required to know when the controller reset has completed and
also if it has completed successfully. For such places, we call
hisi_sas_controller_reset() directly before. That may lead to multiple calls
to this function.
This patch create a per-reset structure which contains a completion structure
and status flag to know when the reset completes and also the status. It is
also in hisi_hba.wq to do reset work.
As all host reset works are done in hisi_hba.wq, we don't worry multiple calls
to hisi_sas_controller_reset().
Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Do a couple of changes for when HISI_SAS_RESET_BIT is set for HBA:
- Clearing ITCT is not necessary
- Remove internal abort as it will fail during reset
Flag sas_dev->dev_type is kept as SAS_PHY_UNUSED.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch do following optimizations to host controller reset:
1. Unblock scsi requests before rescanning topology, as SCSI command need be
used if new device is found during rescanning topology.
2. Remove drain_workqueue(hisi_hba->wq) and drain_workqueue(shost->work_q), as
there is no need to ensure that all PHYs event are done before exiting host
reset.
3. Improve message print level of host reset. Host reset is an important and
very few occurrence event. We should know its progress even when not
debugging.
Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently refreshing the PHY port id after reset is done in the rescan
topology function, which is quite late in the reset process. It could be moved
earlier in the process, as the port id can be refreshed once the PHYs become
ready.
In addition to this, we should set the hisi_sas_dev port id to 0xff (invalid
port id) if all PHYs of this port remain down for the same device.
Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In certain scenarios we may just want to clear the ITCT for a device, and not
free other resources like the SATA bitmap using in v2 hw.
To facilitate this, this patch relocates the code of clearing ITCT from
free_device() to a new hw interface clear_itct(). Then for some hw, we should
not realise free_device() if there's nothing left to do for it.
[mkp: typo]
Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
For function dma_unmap_sg(), the <nents> parameter should be number of
elements in the scatterlist prior to the mapping, not after the mapping.
Fix this usage.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
It is required to initialize the dq spinlock before use, which was not being
done, so fix it. This issue can be detected when CONFIG_DEBUG_SPINLOCK is
enabled.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
With all callbacks converted, and the timer callback prototype
switched over, the TIMER_FUNC_TYPE cast is no longer needed,
so remove it. Conversion was done with the following scripts:
perl -pi -e 's|\(TIMER_FUNC_TYPE\)||g' \
$(git grep TIMER_FUNC_TYPE | cut -d: -f1 | sort -u)
perl -pi -e 's|\(TIMER_DATA_TYPE\)||g' \
$(git grep TIMER_DATA_TYPE | cut -d: -f1 | sort -u)
The now unused macros are also dropped from include/linux/timer.h.
Signed-off-by: Kees Cook <keescook@chromium.org>
This is mostly updates of the usual suspects: lpfc, qla2xxx, hisi_sas,
megaraid_sas, pm80xx, mpt3sas, be2iscsi, hpsa. and a host of minor
updates.
There's no major behaviour change or additions to the core in all of
this, so the potential for regressions should be small (biggest
potential being in the scsi error handler changes).
Signed-off-by: James E.J. Bottomley <jejb@linux.vnet.ibm.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=3O85
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"This is mostly updates of the usual suspects: lpfc, qla2xxx, hisi_sas,
megaraid_sas, pm80xx, mpt3sas, be2iscsi, hpsa. and a host of minor
updates.
There's no major behaviour change or additions to the core in all of
this, so the potential for regressions should be small (biggest
potential being in the scsi error handler changes)"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (203 commits)
scsi: lpfc: Fix hard lock up NMI in els timeout handling.
scsi: mpt3sas: remove a stray KERN_INFO
scsi: mpt3sas: cleanup _scsih_pcie_enumeration_event()
scsi: aacraid: use timespec64 instead of timeval
scsi: scsi_transport_fc: add 64GBIT and 128GBIT port speed definitions
scsi: qla2xxx: Suppress a kernel complaint in qla_init_base_qpair()
scsi: mpt3sas: fix dma_addr_t casts
scsi: be2iscsi: Use kasprintf
scsi: storvsc: Avoid excessive host scan on controller change
scsi: lpfc: fix kzalloc-simple.cocci warnings
scsi: mpt3sas: Update mpt3sas driver version.
scsi: mpt3sas: Fix sparse warnings
scsi: mpt3sas: Fix nvme drives checking for tlr.
scsi: mpt3sas: NVMe drive support for BTDHMAPPING ioctl command and log info
scsi: mpt3sas: Add-Task-management-debug-info-for-NVMe-drives.
scsi: mpt3sas: scan and add nvme device after controller reset
scsi: mpt3sas: Set NVMe device queue depth as 128
scsi: mpt3sas: Handle NVMe PCIe device related events generated from firmware.
scsi: mpt3sas: API's to remove nvme drive from sml
scsi: mpt3sas: API 's to support NVMe drive addition to SML
...
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly. This requires adding a pointer to
hold the timer's target task, as there isn't a link back from slow_task.
Cc: John Garry <john.garry@huawei.com>
Cc: "James E.J. Bottomley" <jejb@linux.vnet.ibm.com>
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>
Cc: Jack Wang <jinpu.wang@profitbricks.com>
Cc: lindar_liu@usish.com
Cc: Jens Axboe <axboe@fb.com>
Cc: Hannes Reinecke <hare@suse.com>
Cc: Johannes Thumshirn <jthumshirn@suse.de>
Cc: Benjamin Block <bblock@linux.vnet.ibm.com>
Cc: Baoyou Xie <baoyou.xie@linaro.org>
Cc: Wei Yongjun <weiyongjun1@huawei.com>
Cc: linux-scsi@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Acked-by: John Garry <john.garry@huawei.com> # for hisi_sas part
Tested-by: John Garry <john.garry@huawei.com> # basic sanity test for hisi_sas
Reviewed-by: Jack Wang <jinpu.wang@profitbricks.com>
Add support for servicing AXI errors handling. We do a host controller
reset for such errors.
Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add support for processing AXI bus fatal errors.
If AXI bus fatal error happen, do controller reset to recover.
Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The CQ event is handled in tasklet context, and it could be delayed if
the system loading is high.
It is possible to run into some problems when executing a host reset
when cq_tasklet_vx_hw() is being executed.
So, prior to host reset, execute tasklet_kill() to ensure that all CQ
tasklets are complete.
Besides, as the function hisi_sas_wait_tasklets_done() is added to do
tasklet_kill(), this patch refactors some code where tasklet_kill() is
used.
Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Use completion to wait on ITCT CLR interrupt finishing before
processing other things when freeing a device.
This is safer than the pre-existing process of polling the register.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add init code of hisi_hba->rst_work for v3 hw. Because v3 hw also need
it to recover controller when some hw errors occurs.
Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Realise get_events() to add DFX feature for v3 hw. Just like v2 hw, We
support the following errors:
- loss_of_dword_sync_count
- invalid_dword_count
- phy_reset_problem_count
- running_disparity_error_count
Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add initialization of register CON_CFG_DRIVER for v3 hw, to limit
number of the times of setup connection.
Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
We should check register PHY_STATE when getting the bitmap of a
wideport, as, if the PHY is not ready, the value of register
PHY_PORT_NUM_MA is not valid.
V2 hw has done this check, and v3 hw should do this check too.
Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The code to print AXI errors in v2 hw driver is repetitive.
This patch condenses the code by looping an array of errors.
Also, a formatting error in one_bit_ecc_errors[] and
multi_bit_ecc_errors[] is fixed.
Signed-off-by: Shiju Jose <shiju.jose@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The function hisi_sas_slot_task_free() is used to free the slot and do
tidy-up of LLDD resources. The LLDD generally should know the state of
a slot and decide when to free it, and it should only be done once.
For some scenarios, we really don't know the state, like when TMF
timeout. In this case, we check task->lldd_task before calling
hisi_sas_slot_task_free().
However, we may miss some scenarios when we should also check
task->lldd_task, and it is not SMP safe to check task->lldd_task as we
don't protect it within spin lock.
This patch is to fix this risk of freeing slot twice, as follows:
1. Check task->lldd_task in the hisi_sas_slot_task_free(), and give
up freeing of this time if task->lldd_task is NULL.
2. Set slot->buf to NULL after it is freed.
Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch adds a NULL check of task->lldd_task before freeing the
slot in SMP path.
This is to guard against the scenario of the slot being freed during
the from the preceding internal abort.
Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When a PHY_FUNC_LINK_RESET is issued, we need to fill the transport
identify_frame to SAS controller before the PHYs are enabled.
Without this, we may find that if a PHY which belonged to a wideport
before the reset may generate a new port id.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently the size of memory we allocate for SATA breakpoint buffer is
incorrect.
The breakpoint memory size should be as follows: 32 (NCQ tags) * 128 *
2048 (max #devs) = 8MB
Currently we only allocate 0.5MB, but get away with it as we never
have SATA device index > 128 typically.
To conserve precious DMA memory (8MB may not be even available), limit
the number of devices per HBA to 1024, which means 4MB of memory
required for SATA breakpoint.
The 1024 device limit applied to all HW versions. For v3 hw, we need
to configure this value.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When adding/removing slots from device list, we need to lock this
operation with hisi_hba lock for safety.
This patch adds missing instances of this.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
We used spin_lock() to grab hisi_hba.lock in two places where
spin_lock_irqsave() should be used, as hisi_hba.lock can be taken in
interrupt context.
This patch is to fix this.
Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When an internal abort times out in hisi_sas_internal_task_abort(),
goto the exit label in and not go through the other task status
checks.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
We already relocated hisi_sas_get_ncq_tag() into common file main.c,
so delete get_ncq_tag_v3_hw() and use hisi_sas_get_ncq_tag() instead.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Remove unused variable sas_ha to clean up build warning
"unused variable sas_ha [-Wunused-variable]"
Fixes: 042ebd293b ("scsi: libsas: kill useless ha_event and do some cleanup")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The ha_event now has only one event HAE_RESET, and this event does
nothing. Kill it and do some cleanup.
This is a preparation for enhance libsas hotplug feature in the next
patches.
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
CC: Johannes Thumshirn <jthumshirn@suse.de>
CC: Ewan Milne <emilne@redhat.com>
CC: Christoph Hellwig <hch@lst.de>
CC: Tomas Henzl <thenzl@redhat.com>
CC: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The bus reset handler is calling I_T Nexus reset, which logically is a
target reset as it need to specify both the initiator and the target.
So move it to target reset.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The driver version is not updated with changes to the driver, so it has
no value, so just get rid of it.
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Instances of kfree(shost) should be replaced with scsi_host_put().
In addition, a missing scsi_host_put() is added for error path in
hisi_sas_shost_alloc_pci() and v3 driver removal.
Signed-off-by: Pan Bian <bianpan2016@163.com> # For main.c changes
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Variable res only holds value 0, so remove it.
This cleans up a coccicheck warning.
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add function to set linkrate for v3 hw.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch updates some register setting according to recommendation
from HW designer and experiment.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Use ACPI "_RST" method to reset the controller, since FLR is not
supported.
Function hisi_sas_stop_phys() is introduced to remove some code
duplication.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch adds calls to kill CQ takslets v3 hw during probe failure.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The channel interrupt is to process all the interrupts except PHY
UP/DOWN and broadcast interrupt. So we need to clear all the interrupts
except those 3 interrupts after processing channel interrupts.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Modify STP link timer from 10ms to 500ms. Also add the register address.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
For v3 hw, internal abort function required status and command buffer to
be set, so add necessary code for this.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add two ATA commands, ATA_CMD_ZAC_MGMT_IN and ATA_CMD_ZAC_MGMT_OUT in
hisi_sas_get_ata_protocol(), to support SATA SMR disk.
Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch is a fix related to freeing a device in v2 hw driver.
Before, we polled to ITCT CLR interrupt to check if a device is free.
This was error prone, as if the interrupt doesn't occur in 10us, we miss
processing it.
To avoid this situation, service this interrupt and sync the event with
a completion.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch adds support to clean-up allocated IRQs and kill tasklets
when probe fails and for driver removal.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch removes some repeated configurations:
(1) The device id of the device is already set in the alloc function, so
we don't need to modify in free device function.
(2) Field dev_type and dev_status are configured in hisi_sas_dev_gone(),
so there is no need for repeated config in free_device_v3_hw.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The code to print ECC errors in v2 hw driver is very repetitive. This
patch condensed the code by looping an array of errors.
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Shiju Jose <shiju.jose@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add DFX feature for v2 hw. We are adding support for
the following errors:
- loss_of_dword_sync_count
- invalid_dword_count
- phy_reset_problem_count
- running_disparity_error_count
Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The value dw0 is the residual bytes when UNDERFLOW error happens, but we
filled the residual with the value of dw3 before. So change the residual
from dw3 to dw0.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Xiang Chen