Firmware asserts when the same CQE is armed twice. This scenario happens during
RSCN stress tests as driver incorrects arms the CQ after the session is
offloaded.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
It is not required to hold rtnl_lock and bnx2fc_dev_lock when calling
bnx2fc_if_destroy, as the locking is only required to serialize creation and
deletion of fcoe instances. More importantly, this unnecessary locking causes
deadlock as bnx2fc_if_destroy calls fc_remove_host holding rtnl_lock.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
When bnx2fc receives an UNREGISTER event on a vlan interface it calls
destroy on all interfaces that matches the physical interface. Add
vlan_id check to destroy only the vlan interface that generated the
event.
Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
ABTS was not issued for timed out REC, as REC completion handler exits out if
the IO completed. Check for timed out REC and issue ABTS before proceeding with
further processing in REC completion handler. Also, initialize rec_retry and
srr_retry before starting the IO.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Link up event is generated to the driver even before vlan discovery has
started. Because of this driver can send discovery solicitation on a stale
vlan. Call fcoe_ctlr_link_up() only when the driver is in enabled state, which
implies the vlan discovery is complete before sending solicitation.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
If the max receive frame size is changed during link down, the driver uses the
same value after linkup unless it is reset to default.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This patch does several things:
- introduces __ethtool_get_settings which is called from ethtool code and
from drivers as well. Put ASSERT_RTNL there.
- dev_ethtool_get_settings() is replaced by __ethtool_get_settings()
- changes calling in drivers so rtnl locking is respected. In
iboe_get_rate was previously ->get_settings() called unlocked. This
fixes it. Also prb_calc_retire_blk_tmo() in af_packet.c had the same
problem. Also fixed by calling __dev_get_by_index() instead of
dev_get_by_index() and holding rtnl_lock for both calls.
- introduces rtnl_lock in bnx2fc_vport_create() and fcoe_vport_create()
so bnx2fc_if_create() and fcoe_if_create() are called locked as they
are from other places.
- use __ethtool_get_settings() in bonding code
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
v2->v3:
-removed dev_ethtool_get_settings()
-added ASSERT_RTNL into __ethtool_get_settings()
-prb_calc_retire_blk_tmo - use __dev_get_by_index() and lock
around it and __ethtool_get_settings() call
v1->v2:
add missing export_symbol
Reviewed-by: Ben Hutchings <bhutchings@solarflare.com> [except FCoE bits]
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since it is already called in the right context with rtnl_lock and dev_mutex
held.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Increase it to NVRAM configured limit or 1024 whichever is less.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a validation step before allowing creation of a new NPIV port.
It checks whether the WWPN passed for the new NPIV port to be created is unique
for the given physical port.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
bnx2x driver would obtain the WWNN/WWPN from the shared memory and can be
obtained by the bnx2fc driver via ndo_fcoe_get_wwn.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
As an initiator, driver need not handle incoming ABTS. It initiates an ABTS if
any IO requests time out.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
- Free session resources before rport logoff
- Do not free session resources in bnx2fc_alloc_session_resc() as it is handled
in caller's error handling path.
- Do not call bnx2fc_free_session_resc() if bnx2fc_init_tgt() fails as cq_lock
is not yet initialized.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
There exists a race condition between CQ doorbell unmap and IO completion path
that arms the CQ which causes a NULL dereference. Protect the ctx_base with
cq_lock to avoid this. Also, wait for the CQ doorbell to be successfully mapped
before arming the CQ.
Also, do not count uncolicited CQ completions for free_sqes.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
During the unsolicited LOGO processing, the session is uploaded and offloaded
after the relogin is complete. In between any new IOs are errored back as the
upload completion flag is set. Upon exhausting the retry count, the application
fails the IOs. Return target busy for all the cases when session is not ready.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
CFC_DELETE is issued 2 secs after CONN_TERM is completed. If the session is
uploaded and offloaded immediately, it has to wait for the connection id to be
available.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Since this flag was never cleared, the driver does not wait for firmware
destroy completions, causing missed KCQEs.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Since the driver holds the reference for vlan netdev, the reference has to be
released by the driver when the vlan device is removed. Driver handles this in
NETDEV_UNREGISTER event.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Move interface specific cleanup functionality to from bnx2fc_if_destroy to
bnx2fc_interface_cleanup. Do not access interface/hba in bnx2fc_if_destroy as
by the time this function is called interface may already be destroyed. This
patch is in preparation to handle NETDEV_UNREGISTER on a vlan device.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Change them to bnx2fc_interface_setup/bnx2fc_interface_cleanup in preperation
for the patches to follow. Interface specific cleanup functionality will be
moved to bnx2fc_interface_cleanup.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
When NPIV ports are created/deleted rapidly there is a race condition between
bnx2fc_vport_destroy() from sysfs and bnx2fc_flogi_resp(), which could try to
delete the NPIV port from the list twice. Fix is to loop through the list of
NPIV ports to find a match, and only when it exists remove it.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
During sequence cleanup, an additional reference for an IO has been
taken. Because of this, the IO is never released into the free list.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Look up p->work_list to process cq completions, and correct the error check for
thread creation.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Reset max receive frame size every time before attempting FLOGI. Without this,
the stale MFS value will be used.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Moves the drivers for Broadcom devices into
drivers/net/ethernet/broadcom/ and the necessary Kconfig and Makefile
changes.
CC: Eilon Greenstein <eilong@broadcom.com>
CC: Michael Chan <mchan@broadcom.com>
CC: Matt Carlson <mcarlson@broadcom.com>
CC: Gary Zambrano <zambrano@broadcom.com>
CC: "Maciej W. Rozycki" <macro@linux-mips.org>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There is no need to cache the ptype in fcoe_rcv_info struct as it is never
used anywhere.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
When there is a single BD for the entire data to be transmitted, use the BD
inside the SGL context and set the cached SGE indication in the task context
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Driver advertises its support for 'retry' bit and 'conf completion' bit in PRLI
params to enable support for 'sequence level error recovery'
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Program the firmware task structure with init_flags indicating the device is
'sequence level error recovery' capable.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Driver decides to initiate REC on REC_TOV timer pop. The firmware maintains the
REC timer and informs the driver as a firmware error message, which is an
unsolicited event to the driver. Driver also issues REC on other unsolicited
events from firmware that indicate data loss.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
For the devices that support sequence level error recovery, based on the REC
response, the firmware has to be informed about the offset from which the
retransmission should happen. Driver initiates sequence cleanup task to
firmware so that the firmware can program the task. Upon the sequence cleanup
completion, SRR is issued to retransmit the sequence.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Based on PRLI response, identify if the target is FCP-2 (seq level error
recovery) capable, and appropriately set the corresponding CONF, REC flags when
offloading the session.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Currently, bnx2fc has a hba structure that can work with only a single vlan
interface. When there is a change in vlan id, it does not have the capability
to switch to different vlan interface. To solve this problem, a new structure
called 'interface' has been introduced, and each hba can now have multiple
interfaces, one per vlan id.
Most of the patch is a moving the interface specific fields from hba to the
interface structure, and appropriately modifying the dereferences. A list of
interfaces (if_list) is maintained along with adapter list. During a create
call, the interface structure is allocated and added to if_list and deleted &
freed on a destroy call. Link events are propagated to all interfaces
belonging to the hba.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (77 commits)
[SCSI] fix crash in scsi_dispatch_cmd()
[SCSI] sr: check_events() ignore GET_EVENT when TUR says otherwise
[SCSI] bnx2i: Fixed kernel panic due to illegal usage of sc->request->cpu
[SCSI] bfa: Update the driver version to 3.0.2.1
[SCSI] bfa: Driver and BSG enhancements.
[SCSI] bfa: Added support to query PHY.
[SCSI] bfa: Added HBA diagnostics support.
[SCSI] bfa: Added support for flash configuration
[SCSI] bfa: Added support to obtain SFP info.
[SCSI] bfa: Added support for CEE info and stats query.
[SCSI] bfa: Extend BSG interface.
[SCSI] bfa: FCS bug fixes.
[SCSI] bfa: DMA memory allocation enhancement.
[SCSI] bfa: Brocade-1860 Fabric Adapter vHBA support.
[SCSI] bfa: Brocade-1860 Fabric Adapter PLL init fixes.
[SCSI] bfa: Added Fabric Assigned Address(FAA) support
[SCSI] bfa: IOC bug fixes.
[SCSI] bfa: Enable ASIC block configuration and query.
[SCSI] bnx2i: Updated copyright and bump version
[SCSI] bnx2i: Modified to skip CNIC registration if iSCSI is not supported
...
Fix up some trivial conflicts in:
- drivers/scsi/bnx2fc/{bnx2fc.h,bnx2fc_fcoe.c}:
Crazy broadcom version number conflicts
- drivers/target/tcm_fc/tfc_cmd.c
Just trivial cleanups done on adjacent lines
The bnx2fc driver needs to handle netdev events on VLAN devices.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Reviewed-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Deleting NPIV port causes a kernel panic when the NPIV port is in the same zone
as the physical port and shares the same LUN. This happens due to the fact that
vport destroy and unsolicited ELS are scheduled to run on the same workqueue,
and vport destroy destroys the lport and the unsolicited ELS tries to access
the invalid lport. This patch fixes this issue by maintaining a list of valid
lports and verifying if the lport is valid or not before accessing it.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Do not set io_req->sc_cmd to NULL until bnx2fc_unmap_sg_list() is called to
enable it to unmap the DMA mappings.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
NIC partitioned interfaces reports the speed of 2500 which was not handled by
the driver.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
New FW/HSI (7.0):
- Added support to 578xx chips
- Improved HSI - much less driver's direct access to the FW internal
memory needed.
New implementation of the HSI handling layer in the bnx2x (bnx2x_sp.c):
- Introduced chip dependent objects that have chip independent interfaces
for configuration of MACs, multicast addresses, Rx mode, indirection table,
fast path queues and function initialization/cleanup.
- Objects functionality is based on the private function pointers, which
allows not only a per-chip but also PF/VF differentiation while still
preserving the same interface towards the driver.
- Objects interface is not influenced by the HSI changes which do not require
providing new parameters keeping the code outside the bnx2x_sp.c invariant
with regard to such HSI chnages.
Changes in a CNIC, bnx2fc and bnx2i modules due to the new HSI.
Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@conan.davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1446 commits)
macvlan: fix panic if lowerdev in a bond
tg3: Add braces around 5906 workaround.
tg3: Fix NETIF_F_LOOPBACK error
macvlan: remove one synchronize_rcu() call
networking: NET_CLS_ROUTE4 depends on INET
irda: Fix error propagation in ircomm_lmp_connect_response()
irda: Kill set but unused variable 'bytes' in irlan_check_command_param()
irda: Kill set but unused variable 'clen' in ircomm_connect_indication()
rxrpc: Fix set but unused variable 'usage' in rxrpc_get_transport()
be2net: Kill set but unused variable 'req' in lancer_fw_download()
irda: Kill set but unused vars 'saddr' and 'daddr' in irlan_provider_connect_indication()
atl1c: atl1c_resume() is only used when CONFIG_PM_SLEEP is defined.
rxrpc: Fix set but unused variable 'usage' in rxrpc_get_peer().
rxrpc: Kill set but unused variable 'local' in rxrpc_UDP_error_handler()
rxrpc: Kill set but unused variable 'sp' in rxrpc_process_connection()
rxrpc: Kill set but unused variable 'sp' in rxrpc_rotate_tx_window()
pkt_sched: Kill set but unused variable 'protocol' in tc_classify()
isdn: capi: Use pr_debug() instead of ifdefs.
tg3: Update version to 3.119
tg3: Apply rx_discards fix to 5719/5720
...
Fix up trivial conflicts in arch/x86/Kconfig and net/mac80211/agg-tx.c
as per Davem.
Use fc_exch_mgr_list_clone to setup em for npiv port.
Also remove redundant vport and lport initializations.
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Acked-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
FW may take more time cleaning up IOs issued to multiple targets.
Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
If the session is not ready yet, we ask the SCSI-ml to retry. However, if the
session is just uploaded, we should not retry, but instead call scsi_done to
fail the IO.
Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Prematurely decrementing the reference may lead to cmd_mgr becoming NULL with
the cmds are still active.
Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
This makes sure that when a driver calls the ethtool's
get/set_settings() callback of another driver, the data passed to it
is clean. This guarantees that speed_hi will be zeroed correctly if
the called callback doesn't explicitely set it: we are sure we don't
get a corrupted speed from the underlying driver. We also take care of
setting the cmd field appropriately (ETHTOOL_GSET/SSET).
This applies to dev_ethtool_get_settings(), which now makes sure it
sets up that ethtool command parameter correctly before passing it to
drivers. This also means that whoever calls dev_ethtool_get_settings()
does not have to clean the ethtool command parameter. This function
also becomes an exported symbol instead of an inline.
All drivers visible to make allyesconfig under x86_64 have been
updated.
Signed-off-by: David Decotigny <decot@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Driver does not detect a new CQE (completion queue entry) if a thread receives
the wakup when it is in TASK_RUNNING state. Fix is to set the state to
TASK_INTERRUPTIBLE while holding the fp_work_lock.
Also, Use __set_current_task() since it is now set inside a spinlock with
synchronization.
Two other related optimizations:
1. After we exit the while (!kthread_should_stop()) loop, use
__set_current_state() since synchronization is no longer needed.
2. Remove set_current_state(TASK_RUNNING) after schedule() since it
should always be TASK_RUNNING after schedule().
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The check for module state MODULE_STATE_LIVE is no longer required for LLDs, as
libfcoe transport takes care of it. Reference:
http://marc.info/?l=linux-scsi&m=129989565903046&w=2
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
bnx2x now uses seperate MTUs for networking and FCoE. FCoE MTU is fixed to 2500
and bnx2fc now needs to match this logic by using FCOE_MTU instead of
netdev->mtu.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
bnx2fc only operates on bnx2x hardware devices and not master bonding
devices, so there is no need to check for bonding. Even if the bnx2x
device is "enslaved" into a bonding device, FCoE is unaffected as it
has its own MAC address and queues.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
tgt lock is needed during -
bnx2fc_return_rqe to protect the rq_prod_idx.
bnx2fc_get_next_rqe to protect rq_cons_idx
Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Cleanup commands are issued to the firmware to cleanup any stuck ios
that are supposed to be implicitly aborted. In the worst case we can
have all scsi ios filling up the free_list and we may not be able to
allocate cleanup tasks. So the driver has to reserve free_list entries
to be able to allocate the cleanup tasks. This reserve free_list common
to all cpus is allocated as one additional entry in the per cpu
free_lists.
In bnx2fc_cmd_alloc(), there is a related fix to use get_cpu() for the
free_list_index. This will prevent using the wrong index if the CPU
is preempted.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Call rtnl_lock instead of rtnl_trylock & restart_syscall. This is bnx2fc
counterpart of fcoe fixes, here is the reference:
https://lists.open-fcoe.org/pipermail/devel/2011-March/011199.html
Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
With kernel debugging enabled, holding cq_lock when calling
bnx2fc_free_session_resc() which calls iounmap() leads to a warning
stack trace [INFO: HARDIRQ-safe -> HARDIRQ-unsafe lock order detected].
iounmap() grabs a HARDIRQ-unsafe vmlist lock, so holding
spin_lock_bh(cq_lock) when calling iounmap() will trigger the LOCKDEP
warning. Since cq_lock is required only to guard against deletion, hold
the lock just before freeing the cq.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
This driver is for Broadcom Netxtreme II 57712 chip. The following
patch contains the driver sources for bnx2fc driver. libfc/libfcoe
changes to enable bnx2fc have already gone through the fcoe
tree. bnx2fc is a SCSI low level driver that interfaces with SCSI
midlayer, libfc, libfcoe, cnic modules. bnx2fc driver uses services
of libfc for slow path operations such as FIP and fabric
discovery. The fast path IO perations are performed after offloading
the session information to the underlying FCoE firmware.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Bhanu Prakash Gollapudi