The USB regulator is controlled by hardware. The software support
was only needed for early hardware (ED) which is no longer supported.
Signed-off-by: Bengt Jonsson <bengt.g.jonsson@stericsson.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The ABx500 is capable of controlling three external regulator supplies.
Most commonly on and off are supported, but if an external regulator
chipset or power supply supports high-power and low-power mode settings,
we can control those too.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The issues probably originated from a typo in the initial submission.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Clean out initialisation that is handled by SoC. Regulator
settings for Vpll (partly), Vsmps1, Vsmps2, Vsmps3 (partly),
Vrf1, Varm, Vape, Vbb, Vmod are cleaned out. They should not
be touched by the kernel.
We also update many of the initialisation values to be more
in-line with the current development efforts of ST-Ericsson
internal engineers.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The data sheet does not specify time delay for voltage selection,
thus remove set_voltage_time_sel and delay setting.
Note, currently set_voltage_time_sel callback returns 0 due to missing
delay settings.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Bengt Jonsson <bengt.g.jonsson@stericsson.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Base on the data provide by Bengt Jönsson, add below enable_time settings:
Worst case enable time from data sheet:
Vana: enable time = 140 us
Vaux1/2: enable time = 200 us
Vaux3: enable time = 450 us
Vintcore: enable time = 750 us
Vamic1/2: enable time = 500 us
Vdmic: enable time = 420 us
VTVout: enable time = 500 us
Vaudio: enable time = 140 us
Vusb: enable time = 150 us
This discussion thread is available at: https://lkml.org/lkml/2013/3/26/795
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Bengt Jonsson <bengt.g.jonsson@stericsson.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This avoid setting is_enabled flag to wrong status if enable/disable fails.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Bengt Jonsson <bengt.g.jonsson@stericsson.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Both ab8500_regulator_mode_ops and ab8500_regulator_ops do not have volt_table
setting, thus we can not use regulator_list_voltage_table for them.
However, they have min_uV setting with n_voltages = 1, so use
regulator_list_voltage_linear instead.
Also remove setting set_voltage_time_sel for ab8500_regulator_mode_ops.
It is used only for fixed voltage, so it does not need to implement
set_voltage_time_sel.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Fix below build error:
CC drivers/regulator/ab8500.o
drivers/regulator/ab8500.c:500:23: error: 'ab8500_regulator_fixed_ops' undeclared here (not in a function)
drivers/regulator/ab8500.c: In function 'ab8500_regulator_probe':
drivers/regulator/ab8500.c:972:8: warning: assignment from incompatible pointer type [enabled by default]
make[2]: *** [drivers/regulator/ab8500.o] Error 1
make[1]: *** [drivers/regulator] Error 2
make: *** [drivers] Error 2
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The ab8500 MFD should not have knowledge about regulator-
specific platform data like number of regulators and
regulator registers. As the regulator platform data is
about to grow with external regulators, this information
is moved to a new structure provided by the regulator
driver.
Signed-off-by: Bengt Jonsson <bengt.g.jonsson@stericsson.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Yvan FILLION <yvan.fillion@stericsson.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch ensures that many of the recent developments pertaining to
the AB8500 regulator device are propagated out into the public arena.
It aims to update some of the existing initialisation values in
accordance with internal ST-Ericsson code submissions. This single
patch was originally a collection of updates which have been squashed
together to aid with clarity.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
There is already before a register mask in the regulator driver
to allow some bits of a register to be initialized. The register
value is defined in the board configuration. This patch puts a
mask in the board configuration to specify which bits should
actually be altered. The purpose with this patch is to avoid
future mistakes when updating the allowed bits in the regulator
driver.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
With this change, Vtvout, Vintcore12, Vaux1, 2 and 3 regulators
support DRMS (Dynamic Regulator Mode Switching) which will
dynamically handle requests for max current consumption from
several consumers and select a suitable regulator mode.
Signed-off-by: Bengt Jonsson <bengt.g.jonsson@stericsson.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Mattias WALLIN <mattias.wallin@stericsson.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Ludovic Barré <ludovic.barre@stericsson.com>
Signed-off-by: Emeric Vigier <emeric.vigier@stericsson.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Bengt JONSSON <bengt.g.jonsson@stericsson.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch supplies access to some extra settings provided by the
AB8500 regulator device. We also update some of the existing
initialisation values in accordance with internal ST-Ericsson code
submissions. This single patch was originally a collection of updates
which have been squashed together to aid with clarity.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
CONFIG_HOTPLUG is going away as an option so __devexit is no
longer needed.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
CONFIG_HOTPLUG is going away as an option so __devinit is no longer
needed.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
CONFIG_HOTPLUG is going away as an option so __devexit_p is no longer
needed.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This encodes the voltage shifts (the number of bits to shift
the register to get to the selector) into the regulator info.
We have several new variants of the AB8500 so this varies a
lot.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This is not required after commit f7df20ec
"regulator: core: Use list_voltage() to read single voltage regulators"
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
We have support for a few new drivers:
- Samsung s2mps11
- Wolfson Microelectronics wm5102 and wm5110
- Marvell 88PM800 and 88PM805
- TI twl6041
We also have our regular driver improvements:
- Device tree and IRQ domain support for STE AB8500
- Regmap and devm_* API conversion for TI tps6586x
- Device tree support for Samsung max77686
- devm_* API conversion for STE AB3100
Besides that, quite a lot of fixing and cleanup for mc13xxx, tps65910,
tps65090, da9052 and twl-core.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=c28c
-----END PGP SIGNATURE-----
Merge tag 'mfd-3.6-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6
Pull MFD bits from Samuel Ortiz:
"We have support for a few new drivers:
- Samsung s2mps11
- Wolfson Microelectronics wm5102 and wm5110
- Marvell 88PM800 and 88PM805
- TI twl6041
We also have our regular driver improvements:
- Device tree and IRQ domain support for STE AB8500
- Regmap and devm_* API conversion for TI tps6586x
- Device tree support for Samsung max77686
- devm_* API conversion for STE AB3100
Besides that, quite a lot of fixing and cleanup for mc13xxx, tps65910,
tps65090, da9052 and twl-core."
Fix up mostly trivial conflicts, with the exception of
drivers/usb/host/ehci-omap.c in particular, which had some
re-organization of the reset sequence (commit 1a49e2ac9651: "EHCI:
centralize controller initialization") that clashed with commit
2761a63945 ("mfd: USB: Fix the omap-usb EHCI ULPI PHY reset fix
issues").
In particular, commit 2761a63945 moved the usb_add_hcd() to the
*middle* of the reset sequence, which clashes fairly badly with the
reset sequence re-organization (although it could have been done inside
the new omap_ehci_init() function).
I left that part of commit 2761a63945 just undone.
* tag 'mfd-3.6-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6: (110 commits)
mfd: Ensure AB8500 platform data is passed through db8500-prcmu to MFD Core
mfd: Arizone core should select MFD_CORE
mfd: Fix arizona-irq.c build by selecting REGMAP_IRQ
mfd: Add debug trace on entering and leaving arizone runtime suspend
mfd: Correct tps65090 cell names
mfd: Remove gpio support from tps6586x core driver
ARM: tegra: defconfig: Enable tps6586x gpio
gpio: tps6586x: Add gpio support through platform driver
mfd: Cache tps6586x register through regmap
mfd: Use regmap for tps6586x register access.
mfd: Use devm managed resources for tps6586x
input: Add onkey support for 88PM80X PMIC
mfd: Add support for twl6041
mfd: Fix twl6040 revision information
mfd: Matches should be NULL when populate anatop child devices
input: ab8500-ponkey: Create AB8500 domain IRQ mapping
mfd: Add missing out of memory check for pcf50633
Documentation: Describe the AB8500 Device Tree bindings
mfd: Add tps65910 32-kHz-crystal-input init
mfd: Drop modifying mc13xxx driver's id_table in probe
...
Now the MFD API is Device Tree aware we can use it for platform
registration again, even when booting with DT enabled. To aid in
Device Node pointer allocation we provide each cell with the
associative compatible string.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The min_uV and max_uV are not really used in the code and misleading because
the min_uV and max_uV settings does not match the value in the voltage table.
For example, we have
static const unsigned int ldo_vaux3_voltages[] = {
1200000,
1500000,
1800000,
2100000,
2500000,
2750000,
2790000,
2910000,
};
With below min_uV/max_uV settings for AB8500_LDO_AUX3.
.min_uV = 1100000,
.max_uV = 3300000,
The min_uV/max_uV for AB8500_LDO_AUX3 seems copy-paste from AB8500_LDO_AUX2
and is wrong.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Also removes set_voltage_time_sel callback from ab8500_regulator_fixed_ops
because the voltage won't change. ( And ab8500_regulator_fixed_ops does not
implement get_voltage_sel so set_voltage_time_sel won't be called )
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The 'name' field in 'struct of_regulator_match' expects to match with
its corresponding regulator device node in the Device Tree. This patch
renames each of the regulators in the ab8500 regulator driver so this
is true.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The 'name' field in 'struct of_regulator_match' expects to match with
its corresponding regulator device node in the Device Tree. This patch
renames each of the regulators in the ab8500 regulator driver so this
is true.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Here we setup the ab8500 regulator driver for DT. We first do
this in the normal way, by providing a match structure during
initialisation, but then we provide information so that
whilst probing we can use existing data structures to do DT
look-ups.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
ab8500's probe() function is becoming quite large, so in the lead
up to Device Tree enablement which will fork the thread of execution
this patch splits it into 3 main areas; basic error checking will
remain in probe(), but regulator register initialisation and regulator
registration have been moved to their own functions which will
be called in sequence by probe() and the DT equivalent.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Rather than adding new arguments to regulator_register() every time we
want to add a new bit of dynamic information at runtime change the function
to take these via a struct. By doing this we avoid needing to do further
changes like the recent addition of device tree support which required each
regulator driver to be updated to take an additional parameter.
The regulator_desc which should (mostly) be static data is still passed
separately as most drivers are able to configure this statically at build
time.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Convert ab8500 to set_voltage_sel and then we can remove
ab8500_get_best_voltage_index function.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This change is required to make ab8500_regulator_get_voltage_sel work.
The regulator core will call set_voltage_time_sel only when get_voltage_sel is
implemented.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6: (59 commits)
rtc: max8925: Add function to work as wakeup source
mfd: Add pm ops to max8925
mfd: Convert aat2870 to dev_pm_ops
mfd: Still check other interrupts if we get a wm831x touchscreen IRQ
mfd: Introduce missing kfree in 88pm860x probe routine
mfd: Add S5M series configuration
mfd: Add s5m series irq driver
mfd: Add S5M core driver
mfd: Improve mc13xxx dt binding document
mfd: Fix stmpe section mismatch
mfd: Fix stmpe build warning
mfd: Fix STMPE I2c build failure
mfd: Constify aat2870-core i2c_device_id table
gpio: Add support for stmpe variant 801
mfd: Add support for stmpe variant 801
mfd: Add support for stmpe variant 610
mfd: Add support for STMPE SPI interface
mfd: Separate out STMPE controller and interface specific code
misc: Remove max8997-muic sysfs attributes
mfd: Remove unused wm831x_irq_data_to_mask_reg()
...
Fix up trivial conflict in drivers/leds/Kconfig due to addition of
LEDS_MAX8997 and LEDS_TCA6507 next to each other.
This moves all the header files related to the abx500 family into
a common include directory below mfd. From now on we place any
subchip header in that directory. Headers previously in e.g.
<linux/mfd/ab8500/gpio.h> get prefixed and are now e.g.
<linux/mfd/abx500/ab8500-gpio.h>. The top-level abstract interface
remains in <linux/mfd/abx500.h>.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
With device tree support for regulators, its needed that the
regulator_dev->dev device has the right of_node attached.
To be able to do this add an additional parameter to the
regulator_register() api, wherein the dt-adapted driver can
then pass this additional info onto the regulator core.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Another group of drivers that are taking advantage of the implicit
presence of module.h -- and will break when we pull the carpet out
from under them during a cleanup. Fix 'em now.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
This uses the new infrastructure to provide proper delays when
enabling or setting the voltage of one specific regulator.
Cc: Bengt Jonsson <bengt.g.jonsson@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
The regulators on the AB8500 have a lot of custom
hardware control settings pertaining to 8 external
signals, settings which are board-specific and need
be provided from the platform at startup.
Initialization added for regulators Vana, VextSupply1,
VextSupply2, VextSupply3, Vaux1, Vaux2, Vaux3, VTVout,
Vintcore12, Vaudio, Vdmic, Vamic1, Vamic2, VrefDDR.
Signed-off-by: Bengt Jonsson <bengt.g.jonsson@stericsson.com>
Reviewed-by: Rickard Andersson <rickard.andersson@stericsson.com>
Reviewed-by: Jonas Aberg <jonas.aberg@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
This patch removes the macros for initializing the regulators.
The purpose is to remove one layer of abstraction and make the
code easier to read.
Signed-off-by: Bengt Jonsson <bengt.g.jonsson@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
The verbose debug outputs register writes and reads that can be
used to debug the driver.
Signed-off-by: Bengt Jonsson <bengt.g.jonsson@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
The regulator enumeration is used for putting the regulator data
in correct place in the info array. This should be matched in the
board configuration.
Variable names are updated to be more consistent, comments are
corrected and macros have been edited to be consistent.
Signed-off-by: Bengt Jonsson <bengt.g.jonsson@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
The AUX3 regulator voltage setting is changed in ab8500 v2 compared
to ab8500 v1. This patch adds v2 support while keeping support for
v1.
Signed-off-by: Bengt Jonsson <bengt.g.jonsson@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
The find_regulator function was unused so it has been removed. The
ab8500 pointer in the regulator info structure was unused and so it
has also been removed.
Signed-off-by: Bengt Jonsson <bengt.g.jonsson@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
For INTCORE and TVOUT regulators, the low power register bit is
included in the mask so that enable will set the regulator in
normal (high power) mode.
ANAMIC1, ANAMIC2, DMIC regulator settings are swapped with each
other so that the correct regulator gets enabled/disabled.
ANA regulator register address is corrected.
Signed-off-by: Bengt Jonsson <bengt.g.jonsson@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
The define for number of regulators is moved from ab8500-core to
ab8500-regulator so that the regulator driver can be updated
independently of ab8500-core. This also changes the platform
configuration structure of ab8500-core so that it contains a
pointer to the regulator_init_data array plus number of
regulators instead of an fixed size array of pointers to
regulator_init_data.
Signed-off-by: Bengt Jonsson <bengt.g.jonsson@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Change the interface used by set_voltage() to report the selected value
to the regulator core in terms of a selector used by list_voltage().
This allows the regulator core to know the voltage that was chosen
without having to do an explict get_voltage(), which would be much more
expensive as it will generally access hardware.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
This patch makes the ab8500 mixed signal chip expose the same
interface for register access as the ab3100, ab3550 and ab5500 chip.
The ab8500_read() and ab8500_write() is removed and replaced with
abx500_get_register_interruptible() and
abx500_set_register_interruptible().
Signed-off-by: Mattias Wallin <mattias.wallin@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
selector is used as array index of info->supported_voltages
Thus the valid value range should be 0 .. info->voltages_len -1
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Mark Brown <broonie@openource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
In current implementation, ab8500_regulator_info[0].regulator is not
unregistered if the error happen at i > 0.
This patch fixes the resource leak and also improves the readability.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
I moved the dereference of "ab8500" below the check for NULL.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Hi Mark,
> I think that's everything.
Please find the updated patch set as below.
>From f4bf7eec4d210db5075c0bce4521d9be6bc76c8c Mon Sep 17 00:00:00 2001
From: Sundar R Iyer <sundar.iyer@stericsson.com>
Date: Sun, 6 Jun 2010 19:12:12 +0530
Subject: [PATCH v3 1/2] regulator: add support for regulators on the ab8500 MFD
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Acked-by: Bengt JONSSON <bengt.g.jonsson@stericsson.com>
Signed-off-by: Sundar R Iyer <sundar.iyer@stericsson.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Lee Jones