In preparation to enabling -Wimplicit-fallthrough, mark switch
cases where we are expecting to fall through.
This patch fixes the following warnings:
drivers/mtd/lpddr/lpddr_cmds.c: In function ‘chip_ready’:
drivers/mtd/lpddr/lpddr_cmds.c:319:6: warning: this statement may fall through [-Wimplicit-fallthrough=]
if (mode == FL_READY && chip->oldstate == FL_READY)
^
drivers/mtd/lpddr/lpddr_cmds.c:322:2: note: here
default:
^~~~~~~
Warning level 3 was used: -Wimplicit-fallthrough=3
This patch is part of the ongoing efforts to enabling
-Wimplicit-fallthrough.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Richard Weinberger <richard@nod.at>
In preparation to enabling -Wimplicit-fallthrough, mark switch
cases where we are expecting to fall through.
This patch fixes the following warnings:
drivers/mtd/devices/phram.c: In function ‘parse_num64’:
drivers/mtd/devices/phram.c:149:11: warning: this statement may fall through [-Wimplicit-fallthrough=]
shift += 10;
~~~~~~^~~~~
drivers/mtd/devices/phram.c:150:4: note: here
case 'M':
^~~~
drivers/mtd/devices/phram.c:151:11: warning: this statement may fall through [-Wimplicit-fallthrough=]
shift += 10;
~~~~~~^~~~~
drivers/mtd/devices/phram.c:152:4: note: here
case 'k':
^~~~
Warning level 3 was used: -Wimplicit-fallthrough=3
This patch is part of the ongoing efforts to enabling
-Wimplicit-fallthrough.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Richard Weinberger <richard@nod.at>
In preparation to enabling -Wimplicit-fallthrough, mark switch
cases where we are expecting to fall through.
This patch fixes the following warnings:
drivers/mtd/chips/cfi_cmdset_0002.c: In function ‘get_chip’:
drivers/mtd/chips/cfi_cmdset_0002.c:870:6: warning: this statement may fall through [-Wimplicit-fallthrough=]
if (mode == FL_READY && chip->oldstate == FL_READY)
^
drivers/mtd/chips/cfi_cmdset_0002.c:873:2: note: here
default:
^~~~~~~
drivers/mtd/chips/cfi_cmdset_0002.c: In function ‘cfi_amdstd_sync’:
drivers/mtd/chips/cfi_cmdset_0002.c:2745:16: warning: this statement may fall through [-Wimplicit-fallthrough=]
chip->state = FL_SYNCING;
~~~~~~~~~~~~^~~~~~~~~~~~
drivers/mtd/chips/cfi_cmdset_0002.c:2750:3: note: here
case FL_SYNCING:
^~~~
Warning level 3 was used: -Wimplicit-fallthrough=3
This patch is part of the ongoing efforts to enabling
-Wimplicit-fallthrough.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Reviewed-by: Tokunori Ikegami <ikegami.t@gmail.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
In preparation to enabling -Wimplicit-fallthrough, mark switch
cases where we are expecting to fall through.
This patch fixes the following warnings:
drivers/mtd/chips/cfi_util.c: In function ‘cfi_build_cmd’:
drivers/mtd/chips/cfi_util.c:110:10: warning: this statement may fall through [-Wimplicit-fallthrough=]
onecmd |= (onecmd << (chip_mode * 32));
~~~~~~~^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/mtd/chips/cfi_util.c:112:2: note: here
case 4:
^~~~
drivers/mtd/chips/cfi_util.c:113:10: warning: this statement may fall through [-Wimplicit-fallthrough=]
onecmd |= (onecmd << (chip_mode * 16));
~~~~~~~^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/mtd/chips/cfi_util.c:114:2: note: here
case 2:
^~~~
drivers/mtd/chips/cfi_util.c: In function ‘cfi_merge_status’:
drivers/mtd/chips/cfi_util.c:163:7: warning: this statement may fall through [-Wimplicit-fallthrough=]
res |= (onestat >> (chip_mode * 32));
~~~~^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/mtd/chips/cfi_util.c:165:2: note: here
case 4:
^~~~
drivers/mtd/chips/cfi_util.c:166:7: warning: this statement may fall through [-Wimplicit-fallthrough=]
res |= (onestat >> (chip_mode * 16));
~~~~^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/mtd/chips/cfi_util.c:167:2: note: here
case 2:
^~~~
Warning level 3 was used: -Wimplicit-fallthrough=3
This patch is part of the ongoing efforts to enabling
-Wimplicit-fallthrough.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Richard Weinberger <richard@nod.at>
The AFS v2 partition type appear in later ARM reference designs
such as RealView, Versatile Express and the 64bit Juno Development
Platform.
The image informations is padded with a 32bit word (4 bytes) on
the 32bit platforms and a 64bit word (8 bytes) on the 64bit
platforms. The boot monitor source code gives at hand that this
is because the first entry in the struct mapped over the image
information is a "next" pointer for a linked list, filled in
by firmware after reading in the info block, and always zero
in the flash. We adjust padding by checking what padding gives
the right checksum.
This was tested on:
- Integrator/AP (v1 partitions)
- RealView PB11MPCore (v2 32bit partitions)
- Juno Development System (v2 64bit partitions)
All systems display the images in flash very nicely as separate
partitions, e.g on Juno:
4 afs partitions found on MTD device 8000000.flash
Creating 4 MTD partitions on "8000000.flash":
0x000000040000-0x0000000c0000 : "fip"
0x000000ec0000-0x0000018c0000 : "Image"
0x000000f00000-0x000000f40000 : "juno"
0x000003ec0000-0x000003f00000 : "bl1"
Cc: Ryan Harkin <ryan.harkin@linaro.org>
Acked-by: Liviu Dudau <liviu.dudau@arm.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Richard Weinberger <richard@nod.at>
Factor the IIS (Image Information Structure) reading into the
partition parser, giving us a single, clean partition parser
function.
Cc: Ryan Harkin <ryan.harkin@linaro.org>
Acked-by: Liviu Dudau <liviu.dudau@arm.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Richard Weinberger <richard@nod.at>
This simplifies the code by factoring in the image footer
parsing into the single function parsing the AFSv1 partitions.
Cc: Ryan Harkin <ryan.harkin@linaro.org>
Acked-by: Liviu Dudau <liviu.dudau@arm.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Richard Weinberger <richard@nod.at>
This breaks out the parsing of v1 partitions so we can later add
a v2 partition parser.
Cc: Ryan Harkin <ryan.harkin@linaro.org>
Acked-by: Liviu Dudau <liviu.dudau@arm.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Richard Weinberger <richard@nod.at>
Instead of reading out the AFS footers twice, create a separate
function to just check if there is a footer or not. Rids a few
local variables and prepare us to join the actual parser into
one function.
Cc: Ryan Harkin <ryan.harkin@linaro.org>
Acked-by: Liviu Dudau <liviu.dudau@arm.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Richard Weinberger <richard@nod.at>
This simplifies the AFS partition parsing to make the code
more straight-forward and readable.
Before this patch the code tried to calculate the memory required
to hold the partition info by adding up the sizes of the strings
of the names and adding that to a single memory allocation,
indexing the name pointers in front of the struct mtd_partition
allocations so all allocated data was in one chunk.
This is overzealous. Instead use kstrdup and bail out,
kfree():ing the memory used for MTD partitions and names alike
on the errorpath.
In the process rename the index variable from idx to i.
Cc: Ryan Harkin <ryan.harkin@linaro.org>
Acked-by: Liviu Dudau <liviu.dudau@arm.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Richard Weinberger <richard@nod.at>
This adds device tree support for AFS partitioning.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Richard Weinberger <richard@nod.at>
This moves the AFS (ARM Firmware Suite) partition parser
for NOR flash down into the parsers subdirectory.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Richard Weinberger <richard@nod.at>
The blackfin architecture has been removed a while ago, so there is
no more need to declare uclinux_ram_map as a global structure.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
When the physmap_of_core.c code was merged into physmap-core.c the
ability to use MTD_PHYSMAP_OF with only MTD_RAM selected was lost.
Restore this by adding MTD_RAM to the dependencies of MTD_PHYSMAP.
Fixes: commit 642b1e8dbe ("mtd: maps: Merge physmap_of.c into physmap-core.c")
Cc: <stable@vger.kernel.org>
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Reviewed-by: Hamish Martin <hamish.martin@alliedtelesis.co.nz>
Signed-off-by: Richard Weinberger <richard@nod.at>
When the gpio-addr-flash.c driver was merged with physmap-core.c the
code to store the current gpio_values was lost. This meant that once a
gpio was asserted it was never de-asserted. Fix this by storing the
current offset in gpio_values like the old driver used to.
Fixes: commit ba32ce95cb ("mtd: maps: Merge gpio-addr-flash.c into physmap-core.c")
Cc: <stable@vger.kernel.org>
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
Allow matching the imagetag parser for fixed partitions defined in the
device tree.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
Move the bcm963xx Image Tag parsing into its own partition parser. This
Allows reusing the parser with different full flash parsers.
While moving it, rename it to bcm963* to better reflect it isn't chip,
but reference implementation specific.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
Add of_match_table support to allow using bcm63xxpart as a full flash
layout parser from device tree.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
Marking a local variable as __xipram causes a warning because of the
noinline attribute:
drivers/mtd/maps/physmap-gemini.c:89:11: error: '__noinline__' attribute only applies to functions [-Werror,-Wignored-attributes]
map_word __xipram ret;
^
include/linux/mtd/xip.h:34:18: note: expanded from macro '__xipram'
#define __xipram noinline __attribute__ ((__section__ (".xiptext")))
I can't see any reason for the anotation anyway, so just remove it here.
Fixes: 9d3b5086f6 ("mtd: physmap_of_gemini: Handle pin control")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Richard Weinberger <richard@nod.at>
- Print all JEDEC ID bytes on error
- Fix comment of spi_nor_find_best_erase_type()
- Add region locking flags for s25fl512s
SPI NOR controller drivers changes:
- intel-spi:
* Avoid crossing 4K address boundary on read/write
* Add support for Intel Comet Lake SPI serial flash
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEHUIqys8OyG1eHf7fS1VPR6WNFOkFAlzP/KQACgkQS1VPR6WN
FOlmeQf/ZVjc9w6e47QEfj3rtN0h9Ly7b+39aw22i2aoBosADSf2vS3ng+ReKJpA
4ZIsqhBPS3VxPFuHW7qZtFf+by69zOz/jRDiDSSeI3JxAEjXOQqExEIGl/+lMErc
Lb6W3xdXrco/HOXNNAMuZuBgM6dTppxN9ruIuoclbpLvh4bxSdgHNzfXguZFFtrJ
YhQBFsm1bQ4VlWtpsSVDDN5LwFRBCk3lbTd4CSWiNYOe4RJ1a8nbMrx4vqxy+fIj
jvltq2kWcUwyVc0R4hEeD5Zz+6+mmbSWeWdrhL343bxo+l0LHeDne7Ni88UHZrQh
Q9bad32JA0WP1YDAt+uOMfvlneOazw==
=FEH1
-----END PGP SIGNATURE-----
Merge tag 'spi-nor/for-5.2' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux into mtd/next
SPI NOR core changes:
- Print all JEDEC ID bytes on error
- Fix comment of spi_nor_find_best_erase_type()
- Add region locking flags for s25fl512s
SPI NOR controller drivers changes:
- intel-spi:
* Avoid crossing 4K address boundary on read/write
* Add support for Intel Comet Lake SPI serial flash
Intel Comet Lake has the same SPI serial flash controller as Ice Lake.
Add Comet Lake PCI ID to the driver list of supported devices.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
- Support having the bad block markers in either the first, second or
last page of a block. The combination of all three location is now
possible.
- Constification of NAND_OP_PARSER(_PATTERN) elements.
- Generic NAND DT bindings changed to yaml format (can be used to
check the proposed bindings. First platform to be fully supported:
sunxi.
- Stopped using several legacy hooks.
- Preparation to use the generic NAND layer with the addition of
several helpers and the removal of the struct nand_chip from generic
functions.
- Kconfig cleanup to prepare the introduction of external ECC engines
support.
- Fallthrough comments.
- Introduction of the SPI-mem dirmap API for SPI-NAND devices.
Raw NAND controller drivers changes:
- nandsim:
* Switch to ->exec-op().
- meson:
* Misc cleanups and fixes.
* New OOB layout.
- Sunxi:
* A23/A33 NAND DMA support.
- Ingenic:
* Full reorganization and cleanup.
* Clear separation between NAND controller and ECC engine.
* Support JZ4740 an JZ4725B.
- Denali:
* Clear controller/chip separation.
* ->exec_op() migration.
* Various cleanups.
- fsl_elbc:
* Enable software ECC support.
- Atmel:
* Sam9x60 support.
- GPMI:
* Introduce the GPMI_IS_MXS() macro.
- Various trivial/spelling/coding style fixes.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE9HuaYnbmDhq/XIDIJWrqGEe9VoQFAly4rnMACgkQJWrqGEe9
VoSBzAgAmSx1rDxiX2033dhVvufCcqMQnkY1fguKo69lYkhgGI1EYwvq2NbGLCf4
rb7n+D1peYhzH/9GKz4/LPQPccoVIQnx9+Z+JMZRzyQ+Z73cuomX/DtQO0AsRZgE
bx88vsbQFtjWv0mVluIEs51e3B/4ya6KPotxUDcaAyp2s/VKPaEI1rpiteUx8lZC
QsPsYQG/ryYiBW0cmopRL6c7ZdXyWi5A0kEdypGyO8ybTxo8xBquFqhbraDlM4U2
2H3Ii3iV9HoVTyjG2nGIA094Ak0U029oWW+P9xAPf1L4z6WIVXD68sazpZng+t8s
HgWP7BYDpcdRj+/Dm1b+uoaJH1fvOQ==
=B7w9
-----END PGP SIGNATURE-----
Merge tag 'nand/for-5.2' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux into mtd/next
NAND core changes:
- Support having the bad block markers in either the first, second or
last page of a block. The combination of all three location is now
possible.
- Constification of NAND_OP_PARSER(_PATTERN) elements.
- Generic NAND DT bindings changed to yaml format (can be used to
check the proposed bindings. First platform to be fully supported:
sunxi.
- Stopped using several legacy hooks.
- Preparation to use the generic NAND layer with the addition of
several helpers and the removal of the struct nand_chip from generic
functions.
- Kconfig cleanup to prepare the introduction of external ECC engines
support.
- Fallthrough comments.
- Introduction of the SPI-mem dirmap API for SPI-NAND devices.
Raw NAND controller drivers changes:
- nandsim:
* Switch to ->exec-op().
- meson:
* Misc cleanups and fixes.
* New OOB layout.
- Sunxi:
* A23/A33 NAND DMA support.
- Ingenic:
* Full reorganization and cleanup.
* Clear separation between NAND controller and ECC engine.
* Support JZ4740 an JZ4725B.
- Denali:
* Clear controller/chip separation.
* ->exec_op() migration.
* Various cleanups.
- fsl_elbc:
* Enable software ECC support.
- Atmel:
* Sam9x60 support.
- GPMI:
* Introduce the GPMI_IS_MXS() macro.
- Various trivial/spelling/coding style fixes.
Since the migration of the driver to stop using the legacy
->select_chip() hook, there is nothing deselecting the target anymore,
thus the selection is not forced at the next access. Ensure the ND_RUN
bit and the interrupts are always in a clean state.
Cc: Daniel Mack <daniel@zonque.org>
Cc: stable@vger.kernel.org
Fixes: b25251414f ("mtd: rawnand: marvell: Stop implementing ->select_chip()")
Suggested-by: Boris Brezillon <boris.brezillon@collabora.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Tested-by: Daniel Mack <daniel@zonque.org>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
Stop using the legacy interface.
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
We will need struct nand_controller soon, so more stuff need to
be parts of struct nandsim.
While we are here, rename "nand" to "ns" to use the same naming scheme
everywhere in nandsim.
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
According to the datasheet of some Cypress SLC NANDs, the bad
block markers can be in the first, second or last page of a block.
So let's check all three locations.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Boris Brezillon <bbrezillon@kernel.org>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
It is known that some ESMT SLC NANDs have been shipped
with the factory bad block markers in the first or last page
of the block, instead of the first or second page. To be on
the safe side, let's check all three locations.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Boris Brezillon <bbrezillon@kernel.org>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Currently supported bad block marker positions within the block are:
* in first page only
* in last page only
* in first or second page
Some ESMT NANDs are known to have been shipped by the manufacturer
with bad block markers in the first or last page, instead of the
first or second page.
Also the datasheets for Cypress/Spansion/AMD NANDs claim that the
first, second *and* last page needs to be checked.
Therefore we make it possible to set NAND_BBM_FIRSTPAGE,
NAND_BBM_SECONDPAGE and NAND_BBM_LASTPAGE independently in any
combination.
To simplify the code, the logic to evaluate the flags is moved to a
a new function nand_bbm_get_next_page().
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Boris Brezillon <bbrezillon@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
To be able to check and set bad block markers in the first and
second page of a block independently of each other, we create
separate flags for both cases.
Previously NAND_BBM_SECONDPAGE meant, that both, the first and the
second page were used. With this patch NAND_BBM_FIRSTPAGE stands for
using the first page and NAND_BBM_SECONDPAGE for using the second
page.
This patch is only for preparation of subsequent changes and does
not implement the logic to actually handle both flags separately.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Boris Brezillon <bbrezillon@kernel.org>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The information about where the manufacturer puts the bad block
markers inside the bad block and in the OOB data is stored in
different places. Let's move this information to the chip struct,
as we did it for rawnand.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The information about where the manufacturer puts the bad block
markers inside the bad block and in the OOB data is stored in
different places. Let's move this information to nand_chip.options
and nand_chip.badblockpos.
As this chip-specific information is not directly related to the
bad block table (BBT), we also rename the flags to NAND_BBM_*.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Documentation/scheduler/completion.txt states:
Calling init_completion() on the same completion object twice is
most likely a bug as it re-initializes the queue to an empty queue and
enqueued tasks could get "lost" - use reinit_completion() in that case,
but be aware of other races.
Initialize nfc->completion in meson_nfc_probe using init_completion and
change the call in meson_nfc_queue_rb to reinit_completion so the logic
matches what the documentation suggests.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Tested-by:Liang Yang <liang.yang@amlogic.com>
Acked-by: Liang Yang <liang.yang@amlogic.com>
Tested-by:Liang Yang <liang.yang@amlogic.com>
Acked-by: Liang Yang <liang.yang@amlogic.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
This simplifies the code because it gets rid of the casts to an
u8-pointer when passing "info_buf" from struct meson_nfc_nand_chip.
Also it gets rid of the cast of the u8 databuf pointer to a void
pointer.
The logic inside meson_nfc_dma_buffer_setup() doesn't care about the
pointer types themselves because it only passes them to dma_map_single
which accepts a void pointer.
No functional changes.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Tested-by:Liang Yang <liang.yang@amlogic.com>
Acked-by: Liang Yang <liang.yang@amlogic.com>
Tested-by:Liang Yang <liang.yang@amlogic.com>
Acked-by: Liang Yang <liang.yang@amlogic.com>
Tested-by:Liang Yang <liang.yang@amlogic.com>
Acked-by: Liang Yang <liang.yang@amlogic.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Use the of_property_count_elems_of_size() helper instead of open-coding
it's logic. As a bonus this will now error out if the "reg" property
values use an incorrect size (anything other than sizeof(u32)).
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Tested-by:Liang Yang <liang.yang@amlogic.com>
Acked-by: Liang Yang <liang.yang@amlogic.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Use the recently introduced struct_size macro instead of open-coding
it's logic.
No functional changes.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Tested-by:Liang Yang <liang.yang@amlogic.com>
Acked-by: Liang Yang <liang.yang@amlogic.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Since the migration of the driver to stop using the legacy
->select_chip() hook, the marvell_nfc_select_chip() helper has been
'renamed' to marvell_nfc_select_target(). Update a left-over reference
to this helper in a comment in the ->resume() path.
Fixes: b25251414f ("mtd: rawnand: marvell: Stop implementing ->select_chip()")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Allwinner NAND controllers can make use of DMA to enhance the I/O
throughput thanks to ECC pipelining. DMA handling with A23/A33 NAND IP
is a bit different than with the older SoCs, hence the introduction of
a new compatible to handle:
* the differences between register offsets,
* the burst length change from 4 to minimum 8,
* drive SRAM accesses through the AHB bus instead of the MBUS.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Before the introduction of A33 NAND DMA support, let's use a platform
data structure for parameters that will differ. Right now, there is
only one compatible with one data structure.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Fix sparse warning:
drivers/mtd/nand/raw/ingenic/ingenic_nand.c:140:32: warning:
symbol 'jz4725b_ooblayout_ops' was not declared. Should it be static?
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Eliminate the following reports from 'scripts/checkpatch.pl --strict'.
CHECK: Prefer kernel type 'u8' over 'uint8_t'
CHECK: Prefer kernel type 'u32' over 'uint32_t'
CHECK: Alignment should match open parenthesis
I slightly changed denali_check_erased_page() to shorten it.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Use the runtime-detected denali->nbanks instead of hard-coded
DENALI_NR_BANKS (=4).
The actual number of banks depends on the IP configuration, and
can be less than DENALI_NR_BANKS. It is pointless to touch
registers of unsupported banks.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Currently, this driver sticks to the legacy NAND model because it was
upstreamed before commit 2d472aba15 ("mtd: nand: document the NAND
controller/NAND chip DT representation"). However, relying on the
dummy_controller is already deprecated.
Switch over to the new controller/chip representation.
The struct denali_nand_info has been split into denali_controller
and denali_chip, to contain the controller data, per-chip data,
respectively.
One problem is, this commit changes the DT binding. So, as always,
the backward compatibility must be taken into consideration.
In the new binding, the controller node expects
#address-cells = <1>;
#size-cells = <0>;
... since the child nodes represent NAND chips.
In the old binding, the controller node may have subnodes, but they
are MTD partitions.
The denali_dt_is_legacy_binding() exploits it to distinguish old/new
platforms.
Going forward, the old binding is only allowed for existing DT files.
I updated the binding document.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
As Documentation/process/coding-style.rst says, choose label names
which say what the goto does. The out_<action> label style is already
used in denali_dt.c. Rename likewise for denali_pci.c
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Use 'bool' type for the following boolean parameters.
- write (write or read?)
- dma_avail (DMA engine available or not?)
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Since (u32 *) can accept an opaque pointer, the explicit casting
from (void *) to (u32 *) is redundant. Change the function argument type
to remove the casts.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The Denali IP adopts the syndrome page layout (payload and ECC are
interleaved). The *_page_raw() and *_oob() callbacks are complicated
because they must hide the underlying layout used by the hardware,
and always return contiguous in-band and out-of-band data.
The Denali IP cannot reuse nand_{read,write}_page_raw_syndrome()
in nand_base.c because its hardware ECC engine skips some of first
bytes in OOB. That is why this driver implements specially-crafted
*_page_raw() and *_oob() hooks.
Currently, similar code is duplicated to reorganize the data layout.
For example, denali_read_page_raw() and denali_write_page_raw() look
almost the same. The complexity is partly due to the DMA transfer
used for better performance of *_page_raw() accessors.
On second thought, we do not need to care about their performance
because MTD_OPS_RAW is rarely used.
Let's focus on code cleanups rather than the performance. This commit
removes the internal buffer for DMA, and factors out as much code as
possible.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
With the recent refactoring, the NAND driver hooks now take a pointer
to nand_chip. Add to_denali() in order to convert (struct nand_chip *)
to (struct denali_nand_info *) directly. It is more useful than the
current mtd_to_denali().
I changed some helper functions to take (struct nand_chip *). This will
avoid pointer conversion back and forth, and ease further development.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Wrong copy/paste from the previous block, the error message should
refer to #size-cells instead of #address-cells.
Fixes: f88fc122cc ("mtd: nand: Cleanup/rework the atmel_nand driver")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Move the code that choses ECC into _attach_chip, which is executed only
after the chip->ecc.* properties were loaded from device-tree. This way
we know which ECC method was chosen by the device-tree and can set
methods appropriately.
The chip->ecc.*page methods should be set to fsl_elbc_*page only in HW
ECC mode.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Move the fsl_elbc_attach_chip function after the definitions of
fsl_elbc_read_page and friends in preparation for the next patch.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
When enabling CONFIG_MTD_NAND_ECC_SW_BCH as a module, the
MTD_NAND_ECC_SW_BCH depends on MTD_NAND, but the module controlled by
MTD_NAND links against the module controlled by MTD_NAND_ECC_SW_BCH.
This leads to the following link failure.
aarch64-linux-gnu-ld: drivers/mtd/nand/raw/nand_base.o: in function `nand_cleanup':
../drivers/mtd/nand/raw/nand_base.c:5886: undefined reference to `nand_bch_free'
aarch64-linux-gnu-ld: ../drivers/mtd/nand/raw/nand_base.c:5886:(.text+0x9928): relocation truncated to fit: R_AARCH64_CALL26 against undefined symbol `nand_bch_free'
aarch64-linux-gnu-ld: drivers/mtd/nand/raw/nand_base.o: in function `nand_set_ecc_soft_ops':
../drivers/mtd/nand/raw/nand_base.c:5093: undefined reference to `nand_bch_calculate_ecc'
aarch64-linux-gnu-ld: ../drivers/mtd/nand/raw/nand_base.c:5093:(.text+0xe914): relocation truncated to fit: R_AARCH64_ADR_PREL_PG_HI21 against undefined symbol `nand_bch_calculate_ecc'
aarch64-linux-gnu-ld: ../drivers/mtd/nand/raw/nand_base.c:5093: undefined reference to `nand_bch_calculate_ecc'
aarch64-linux-gnu-ld: ../drivers/mtd/nand/raw/nand_base.c:5094: undefined reference to `nand_bch_correct_data'
aarch64-linux-gnu-ld: ../drivers/mtd/nand/raw/nand_base.c:5094:(.text+0xe934): relocation truncated to fit: R_AARCH64_ADR_PREL_PG_HI21 against undefined symbol `nand_bch_correct_data'
aarch64-linux-gnu-ld: ../drivers/mtd/nand/raw/nand_base.c:5094: undefined reference to `nand_bch_correct_data'
aarch64-linux-gnu-ld: ../drivers/mtd/nand/raw/nand_base.c:5148: undefined reference to `nand_bch_init'
aarch64-linux-gnu-ld: ../drivers/mtd/nand/raw/nand_base.c:5148:(.text+0xebbc): relocation truncated to fit: R_AARCH64_CALL26 against undefined symbol `nand_bch_init'
Rework CONFIG_MTD_NAND_ECC_SW_BCH from tristate to bool,
and then link the nand_bch.o file into nand.ko if its enabled.
Fixes: 51ef1d0b2095 ("mtd: nand: Clarify Kconfig entry for software BCH ECC algorithm")
Signed-off-by: Anders Roxell <anders.roxell@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Prepare changes that will lay in this file to better express what is
NAND related and what is not in menuconfig.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
MTD_NAND is large and encloses much more than what the symbol is
actually used for: raw NAND. Clarify the symbol by naming it
MTD_RAW_NAND instead.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
This list is a mess, while some items should probably not be in the
raw/ sub-directory, others are definitely at the right place but not
with the right description. Write uniform titles and group IPs by
vendor.
NAND controllers will appear under the list named "Raw/parallel NAND
flash controllers" while the other drivers will appear under
"Misc". Software ECC engines will later be moved out of the raw/
directory.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The software Hamming ECC correction implementation is referred as
MTD_NAND_ECC which is too generic. Rename it
MTD_NAND_ECC_SW_HAMMING. Also rename MTD_NAND_ECC_SMC which is an
SMC quirk in the Hamming implementation as
MTD_NAND_ECC_SW_HAMMING_SMC.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
There is no point in having two distinct entries, merge them and
rename the symbol for more clarity: MTD_NAND_ECC_SW_BCH
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
mmiowb() is now implied by spin_unlock() on architectures that require
it, so there is no reason to call it from driver code. This patch was
generated using coccinelle:
@mmiowb@
@@
- mmiowb();
and invoked as:
$ for d in drivers include/linux/qed sound; do \
spatch --include-headers --sp-file mmiowb.cocci --dir $d --in-place; done
NOTE: mmiowb() has only ever guaranteed ordering in conjunction with
spin_unlock(). However, pairing each mmiowb() removal in this patch with
the corresponding call to spin_unlock() is not at all trivial, so there
is a small chance that this change may regress any drivers incorrectly
relying on mmiowb() to order MMIO writes between CPUs using lock-free
synchronisation. If you've ended up bisecting to this commit, you can
reintroduce the mmiowb() calls using wmb() instead, which should restore
the old behaviour on all architectures other than some esoteric ia64
systems.
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
nand_device embeds a nand_ecc_req object which contains the minimum
strength and step-size required by the NAND device.
Drop the chip->ecc_{strength,step}_ds fields and use
chip->base.eccreq.{strength,step_size} instead.
Signed-off-by: Boris Brezillon <bbrezillon@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
The same information is provided by nanddev_ntargets().
Signed-off-by: Boris Brezillon <bbrezillon@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
The target size can now be returned by nanddev_get_targetsize(). Get
rid of the chip->chipsize field and use this helper instead.
Signed-off-by: Boris Brezillon <bbrezillon@kernel.org>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Now that we inherit from nand_device, we can use
nand_device->memorg.bits_per_cell instead of having our own field at
the nand_chip level.
Signed-off-by: Boris Brezillon <bbrezillon@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
nanddev_mtd_max_bad_blocks() is implemented by the generic NAND layer
and is already doing what we need. Reuse this function instead of
having our own implementation.
While at it, get rid of the ->max_bb_per_die and ->blocks_per_die
fields which are now unused.
Signed-off-by: Boris Brezillon <bbrezillon@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Looking at the field names it's hard to tell what ->data_buf, ->pagebuf
and ->pagebuf_bitflips are for. Clarify that by moving those fields
in a sub-struct named pagecache.
Signed-off-by: Boris Brezillon <bbrezillon@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
We plan to move cache related fields to a pagecache struct in nand_chip
but some drivers access ->pagebuf directly to invalidate the cache
before they start using ->data_buf.
Let's provide an helper that returns a pointer to ->data_buf after
invalidating the cache.
Signed-off-by: Boris Brezillon <bbrezillon@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
In order to use some of the nanddev_xxx() helpers, we need to
initialize the nand_device object embedded in nand_chip using
nanddev_init(). This requires implementing nand_ops.
We also drop useless mtd->xxx initialization when they're already taken
case of by nanddev_init().
Signed-off-by: Boris Brezillon <bbrezillon@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
If we want to use the generic NAND layer, we need to have the memorg
struct appropriately filled. Patch the detection code to fill this
struct.
Signed-off-by: Boris Brezillon <bbrezillon@kernel.org>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
We just have to use nanddev_mtd_max_bad_blocks().
Signed-off-by: Boris Brezillon <bbrezillon@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
NAND datasheets usually give the maximum number of bad blocks per LUN
and this number can be used to help upper layers decide how much blocks
they should reserve for bad block handling.
Add a max_bad_eraseblocks_per_lun to the nand_memory_organization
struct and update the NAND_MEMORG() macro (and its users) accordingly.
We also provide a default mtd->_max_bad_blocks() implementation.
Signed-off-by: Boris Brezillon <bbrezillon@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Specify the oob layout operation to avoid no oob scheme defined for
some nand flash.
Fixes: 8fae856c53 ("mtd: rawnand: meson: add support for Amlogic NAND flash controller")
Signed-off-by: Liang Yang <liang.yang@amlogic.com>
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
of_match_device can return NULL if there is no matching device. Avoid
a potential NULL pointer dereference by checking for the return value
and passing the error upstream.
Signed-off-by: Aditya Pakki <pakki001@umn.edu>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The generic layout for BBT markers will most likely overlap with our
ECC bytes in the OOB, so move the BBT markers outside the OOB area.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The Ben Nanonote from Qi Hardware expects a specific OOB layout on its
NAND.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The boot ROM of the JZ4725B SoC expects a specific OOB layout on the
NAND, so we use it unconditionally in the ingenic-nand driver.
Also add the jz4725b-bch driver to support the JZ4725B-specific BCH
hardware.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Add support for probing the ingenic-nand driver on the JZ4740 SoC from
Ingenic, and the jz4740-ecc driver to support the JZ4740-specific
ECC hardware.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Use the 'ecc-engine' standard property instead of the custom
'ingenic,bch-controller' custom property, which is now deprecated.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The ingenic-nand driver uses an API provided by the jz4780-bch driver.
This makes it difficult to support other SoCs in the jz4780-bch driver.
To work around this, we separate the API functions from the SoC-specific
code, so that these API functions are SoC-agnostic.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
In function do_write_buffer(), in the for loop, there is a case
chip_ready() returns 1 while chip_good() returns 0, so it never
break the loop.
To fix this, chip_good() is enough and it should timeout if it stay
bad for a while.
Fixes: dfeae1073583("mtd: cfi_cmdset_0002: Change write buffer to check correct value")
Signed-off-by: Yi Huaijie <yihuaijie@huawei.com>
Signed-off-by: Liu Jian <liujian56@huawei.com>
Reviewed-by: Tokunori Ikegami <ikegami_to@yahoo.co.jp>
Signed-off-by: Richard Weinberger <richard@nod.at>
Both the BP[0-2] bits and the TBPROT bit are supported on this chip.
Tested and verified on a Cypress s25fl512s.
Signed-off-by: Jonas Bonn <jonas@norrbonn.se>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
It was observed that reads crossing 4K address boundary are failing.
This limitation is mentioned in Intel documents:
Intel(R) 9 Series Chipset Family Platform Controller Hub (PCH) Datasheet:
"5.26.3 Flash Access
Program Register Access:
* Program Register Accesses are not allowed to cross a 4 KB boundary..."
Enhanced Serial Peripheral Interface (eSPI)
Interface Base Specification (for Client and Server Platforms):
"5.1.4 Address
For other memory transactions, the address may start or end at any byte
boundary. However, the address and payload length combination must not
cross the naturally aligned address boundary of the corresponding Maximum
Payload Size. It must not cross a 4 KB address boundary."
Avoid this by splitting an operation crossing the boundary into two
operations.
Fixes: 8afda8b26d ("spi-nor: Add support for Intel SPI serial flash controller")
Cc: stable@vger.kernel.org
Reported-by: Romain Porte <romain.porte@nokia.com>
Tested-by: Pascal Fabreges <pascal.fabreges@nokia.com>
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
If identification of an SPI NOR FLASH fails, the JEDEC ID is printed,
which is stored in the first 3 bytes of the ID read from the FLASH.
However, the extended JEDEC ID, which is stored in the remaining bytes,
also matters, as it is used for identification of some FLASH types.
Print all (currently 6) ID bytes read to ease failure analysis and
debugging.
Suggested-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The jz4780_bch_init name was confusing, as it suggested that its content
should be executed once at init time, whereas what the function really
does is reset the hardware for a new ECC operation.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The jz4780_nand driver will be modified to handle all the Ingenic
JZ47xx SoCs that the upstream Linux kernel supports (JZ4740, JZ4725B,
JZ4770, JZ4780), so it makes sense to rename it.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Use SPDX license notifiers instead of GPLv2 license text in the headers.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Reviewed-by: Boris Brezillon <bbrezillon@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Before adding support for more SoCs and seeing the number of files for
these drivers grow, we move them to their own subfolder to keep it tidy.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
meson_nfc_dma_buffer_setup() is called with the "info" buffer which is
allocated a few lines before using kzalloc(). If
meson_nfc_dma_buffer_setup() fails we need to free the allocated "info"
buffer instead of only freeing it upon success.
Fixes: 8fae856c53 ("mtd: rawnand: meson: add support for Amlogic NAND flash controller")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Acked-by: Liang Yang <liang.yang@amlogic.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
kzalloc() can return NULL if memory could not be allocated. Check the
return value of the kzalloc() call in meson_nfc_read_buf() to make it
consistent with other memory allocations within the meson_nand driver.
Fixes: 8fae856c53 ("mtd: rawnand: meson: add support for Amlogic NAND flash controller")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Acked-by: Liang Yang <liang.yang@amlogic.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The sam9x60 board defines the CCFG_EBICSA register under SFR,
and not as a MATRIX register, as previous boards do.
NAND Flash I/Os are connected to D16–D23, thus
SFR_CCFG_EBICSA.NFD0_ON_D16 is set to 1.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The sam9x60 board defines the CCFG_EBICSA register under SFR,
and not as a MATRIX register, as previous boards do. Add a
more generic name for the EBICSA regmap, as a prerequisite for
sam9x60 nand controller support.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
In preparation to enabling -Wimplicit-fallthrough, mark switch
cases where we are expecting to fall through.
This patch fixes the following warning:
drivers/mtd/nand/raw/diskonchip.c: In function ‘doc_probe’:
./include/linux/printk.h:303:2: warning: this statement may fall through [-Wimplicit-fallthrough=]
printk(KERN_ERR pr_fmt(fmt), ##__VA_ARGS__)
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/mtd/nand/raw/diskonchip.c:1479:4: note: in expansion of macro ‘pr_err’
pr_err("DiskOnChip Millennium Plus 32MB is not supported, ignoring.\n");
^~~~~~
drivers/mtd/nand/raw/diskonchip.c:1480:3: note: here
default:
^~~~~~~
drivers/mtd/nand/raw/nandsim.c: In function ‘ns_init_module’:
drivers/mtd/nand/raw/nandsim.c:2254:22: warning: this statement may fall through [-Wimplicit-fallthrough=]
chip->bbt_options |= NAND_BBT_NO_OOB;
drivers/mtd/nand/raw/nandsim.c:2255:2: note: here
case 1:
^~~~
drivers/mtd/nand/raw/nuc900_nand.c: In function ‘nuc900_nand_command_lp’:
./arch/x86/include/asm/io.h:91:22: warning: this statement may fall through [-Wimplicit-fallthrough=]
#define __raw_writel __writel
drivers/mtd/nand/raw/nuc900_nand.c:52:2: note: in expansion of macro ‘__raw_writel’
__raw_writel((val), (dev)->reg + REG_SMCMD)
^~~~~~~~~~~~
drivers/mtd/nand/raw/nuc900_nand.c:196:3: note: in expansion of macro ‘write_cmd_reg’
write_cmd_reg(nand, NAND_CMD_READSTART);
^~~~~~~~~~~~~
drivers/mtd/nand/raw/nuc900_nand.c:197:2: note: here
default:
^~~~~~~
drivers/mtd/nand/raw/omap_elm.c: In function ‘elm_context_restore’:
drivers/mtd/nand/raw/omap_elm.c:512:4: warning: this statement may fall through [-Wimplicit-fallthrough=]
elm_write_reg(info, ELM_SYNDROME_FRAGMENT_4 + offset,
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
regs->elm_syndrome_fragment_4[i]);
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/mtd/nand/raw/omap_elm.c:514:3: note: here
case BCH8_ECC:
^~~~
drivers/mtd/nand/raw/omap_elm.c:517:4: warning: this statement may fall through [-Wimplicit-fallthrough=]
elm_write_reg(info, ELM_SYNDROME_FRAGMENT_2 + offset,
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
regs->elm_syndrome_fragment_2[i]);
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/mtd/nand/raw/omap_elm.c:519:3: note: here
case BCH4_ECC:
^~~~
drivers/mtd/nand/raw/omap_elm.c: In function ‘elm_context_save’:
drivers/mtd/nand/raw/omap_elm.c:466:37: warning: this statement may fall through [-Wimplicit-fallthrough=]
regs->elm_syndrome_fragment_4[i] = elm_read_reg(info,
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~^~~~~~~~~~~~~~~~~~~~
ELM_SYNDROME_FRAGMENT_4 + offset);
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/mtd/nand/raw/omap_elm.c:468:3: note: here
case BCH8_ECC:
^~~~
drivers/mtd/nand/raw/omap_elm.c:471:37: warning: this statement may fall through [-Wimplicit-fallthrough=]
regs->elm_syndrome_fragment_2[i] = elm_read_reg(info,
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~^~~~~~~~~~~~~~~~~~~~
ELM_SYNDROME_FRAGMENT_2 + offset);
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/mtd/nand/raw/omap_elm.c:473:3: note: here
case BCH4_ECC:
^~~~
Warning level 3 was used: -Wimplicit-fallthrough=3
This patch is part of the ongoing efforts to enabling
-Wimplicit-fallthrough.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Introduce a GPMI_IS_MXS() macro to take into account the cases
when mx23 or mx28 are used, which helps readability.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Make use of the spi-mem direct mapping API to let advanced controllers
optimize read/write operations when they support direct mapping.
Signed-off-by: Boris Brezillon <bbrezillon@kernel.org>
Cc: Stefan Roese <sr@denx.de>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Tested-by: Stefan Roese <sr@denx.de>
- A new interface for UBI to deal better with read disturb
- Reject unsupported ioctl flags in UBIFS (xfstests found it)
-----BEGIN PGP SIGNATURE-----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=DlM9
-----END PGP SIGNATURE-----
Merge tag 'upstream-5.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rw/ubifs
Pull UBI and UBIFS updates from Richard Weinberger:
- A new interface for UBI to deal better with read disturb
- Reject unsupported ioctl flags in UBIFS (xfstests found it)
* tag 'upstream-5.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rw/ubifs:
ubi: wl: Silence uninitialized variable warning
ubifs: Reject unsupported ioctl flags explicitly
ubi: Expose the bitrot interface
ubi: Introduce in_pq()
This condition needs to be fipped around because "err" is uninitialized
when "force" is set. The Smatch static analysis tool complains and
UBsan will also complain at runtime.
Fixes: 663586c0a8 ("ubi: Expose the bitrot interface")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Nathan Chancellor <natechancellor@gmail.com>
Tested-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
A fairly quiet release for SPI, the biggest thing is the conversion to
use GPIO descriptors which is now 90% done but still needs some
stragglers converting.
- Support for inter-word delays.
- Conversion of the core and most drivers to use GPIO descriptors for
GPIO controlled chip selects.
- New drivers for NXP FlexSPI and QuadSPI, SiFive and Spreadtrum.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAlx9WtETHGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0DfrB/92O47HJfHg1xIgOp4BLzT8lA5zQEsy
a8ApcLVLvY6mSfbB/G7RosfoPwTc1eZP5Q2BqzQOBIO+507ao4AcASARmkTwjwkC
eRUJ/THkGyGurs8POtnc5YJlHsT1t743QpqlUNekt+NqognlkPccgc5bNgixfuPD
eVSwVC85SKP3gCpAjVb6FFFmlWr8AKdlgx+41h9QpMNG/85H6xgo4C4Wlajt42/E
wNx+WXzlPyzB5Lc3IGPeF/I/Hu/Ta3hUZLTVpWi5ubM8p4SYGmMZ9l8sURPCz1pK
UMZFpJxx8DWwkj2F/FkoLasfiRqUHIP9K7NfKF0u2xdNbhEk1GA3NAG0
=ctKG
-----END PGP SIGNATURE-----
Merge tag 'spi-v5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi updates from Mark Brown:
"A fairly quiet release for SPI, the biggest thing is the conversion to
use GPIO descriptors which is now 90% done but still needs some
stragglers converting.
Summary:
- Support for inter-word delays
- Conversion of the core and most drivers to use GPIO descriptors for
GPIO controlled chip selects
- New drivers for NXP FlexSPI and QuadSPI, SiFive and Spreadtrum"
* tag 'spi-v5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (104 commits)
spi: sh-msiof: Restrict bits per word to 8/16/24/32 on R-Car Gen2/3
spi: sifive: Remove redundant dev_err call in sifive_spi_probe()
spi: sifive: Remove spi_master_put in sifive_spi_remove()
spi: spi-gpio: fix SPI_CS_HIGH capability
spi: pxa2xx: Setup maximum supported DMA transfer length
spi: sifive: Add driver for the SiFive SPI controller
spi: sifive: Add DT documentation for SiFive SPI controller
spi: sprd: Add a prefix for SPI DMA channel macros
spi: sprd: spi: sprd: Add DMA mode support
dt-bindings: spi: Add the DMA properties for the SPI dma mode
spi: sprd: Add the SPI irq function for the SPI DMA mode
dt-bindings: spi: imx: Add an entry for the i.MX8QM compatible
spi: use gpio[d]_set_value_cansleep for setting chipselect GPIO
spi: gpio: Advertise support for SPI_CS_HIGH
spi: sh-msiof: Replace spi_master by spi_controller
spi: sh-hspi: Replace spi_master by spi_controller
spi: rspi: Replace spi_master by spi_controller
spi: atmel-quadspi: add support for sam9x60 qspi controller
dt-bindings: spi: atmel-quadspi: QuadSPI driver for Microchip SAM9X60
spi: atmel-quadspi: add support for named peripheral clock
...
- Use struct_size() where appropriate
- mtd_{read,write}() as wrappers around mtd_{read,write}_oob()
- Fix misuse of PTR_ERR() in docg3
- Coding style improvements in mtdcore.c
SPI NOR changes:
Core changes:
- Add support of octal mode I/O transfer
- Add a bunch of SPI NOR entries to the flash_info table
SPI NOR controller driver changes:
- cadence-quadspi:
* Add support for Octal SPI controller
* write upto 8-bytes data in STIG mode
- mtk-quadspi:
* rename config to a common one
* add SNOR_HWCAPS_READ to spi_nor_hwcaps mask
- Add Tudor as SPI-NOR co-maintainer
NAND changes
NAND core changes:
- Fourth batch of fixes/cleanup to the raw NAND core impacting various
controller drivers (Sunxi, Marvell, MTK, TMIO, OMAP2).
- Checking the return code of nand_reset() and nand_readid_op().
- Removing ->legacy.erase and single_erase().
- Simplifying the locking.
- Several implicit fall through annotations.
Raw NAND controllers drivers changes:
- Fixing various possible object reference leaks (MTK, JZ4780, Atmel).
- ST:
* Adding support for STM32 FMC2 NAND flash controller.
- Meson:
* Adding support for Amlogic NAND flash controller.
- Denali:
* Several cleanup patches.
- Sunxi:
* Several cleanup patches.
- FSMC:
* Disabling NAND on remove().
* Resetting NAND timings on resume().
SPI-NAND drivers changes:
- Toshiba:
* Adding support for all Toshiba products.
- Macronix:
* Fixing ECC status read.
- Gigadevice:
* Adding support for GD5F1GQ4UExxG.
-----BEGIN PGP SIGNATURE-----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=wIHY
-----END PGP SIGNATURE-----
Merge tag 'mtd/for-5.1' of git://git.infradead.org/linux-mtd
Pull MTD updates from Boris Brezillon:
"Core MTD changes:
- Use struct_size() where appropriate
- mtd_{read,write}() as wrappers around mtd_{read,write}_oob()
- Fix misuse of PTR_ERR() in docg3
- Coding style improvements in mtdcore.c
SPI NOR changes:
Core changes:
- Add support of octal mode I/O transfer
- Add a bunch of SPI NOR entries to the flash_info table
SPI NOR controller driver changes:
- cadence-quadspi:
* Add support for Octal SPI controller
* write upto 8-bytes data in STIG mode
- mtk-quadspi:
* rename config to a common one
* add SNOR_HWCAPS_READ to spi_nor_hwcaps mask
- Add Tudor as SPI-NOR co-maintainer
NAND changes:
NAND core changes:
- Fourth batch of fixes/cleanup to the raw NAND core impacting
various controller drivers (Sunxi, Marvell, MTK, TMIO, OMAP2).
- Check the return code of nand_reset() and nand_readid_op().
- Remove ->legacy.erase and single_erase().
- Simplify the locking.
- Several implicit fall through annotations.
Raw NAND controllers drivers changes:
- Fix various possible object reference leaks (MTK, JZ4780, Atmel)
- ST:
* Add support for STM32 FMC2 NAND flash controller
- Meson:
* Add support for Amlogic NAND flash controller
- Denali:
* Several cleanup patches
- Sunxi:
* Several cleanup patches
- FSMC:
* Disable NAND on remove()
* Reset NAND timings on resume()
SPI-NAND drivers changes:
- Toshiba:
* Add support for all Toshiba products.
- Macronix:
* Fix ECC status read.
- Gigadevice:
* Add support for GD5F1GQ4UExxG"
* tag 'mtd/for-5.1' of git://git.infradead.org/linux-mtd: (64 commits)
mtd: spi-nor: Fix wrong abbreviation HWCPAS
mtd: spi-nor: cadence-quadspi: fix spelling mistake: "Couldnt't" -> "Couldn't"
mtd: spi-nor: Add support for en25qh64
mtd: spi-nor: Add support for MX25V8035F
mtd: spi-nor: Add support for EN25Q80A
mtd: spi-nor: cadence-quadspi: Add support for Octal SPI controller
dt-bindings: cadence-quadspi: Add new compatible for AM654 SoC
mtd: spi-nor: split s25fl128s into s25fl128s0 and s25fl128s1
mtd: spi-nor: cadence-quadspi: write upto 8-bytes data in STIG mode
mtd: spi-nor: Add support for mx25u3235f
mtd: rawnand: denali_dt: remove single anonymous clock support
mtd: rawnand: mtk: fix possible object reference leak
mtd: rawnand: jz4780: fix possible object reference leak
mtd: rawnand: atmel: fix possible object reference leak
mtd: rawnand: fsmc: Disable NAND on remove()
mtd: rawnand: fsmc: Reset NAND timings on resume()
mtd: spinand: Add support for GigaDevice GD5F1GQ4UExxG
mtd: rawnand: denali: remove unused dma_addr field from denali_nand_info
mtd: rawnand: denali: remove unused function argument 'raw'
mtd: rawnand: denali: remove unneeded denali_reset_irq() call
...
- Fourth batch of fixes/cleanup to the raw NAND core impacting various
controller drivers (Sunxi, Marvell, MTK, TMIO, OMAP2).
- Checking the return code of nand_reset() and nand_readid_op().
- Removing ->legacy.erase and single_erase().
- Simplifying the locking.
- Several implicit fall through annotations.
Raw NAND controllers drivers changes:
- Fixing various possible object reference leaks (MTK, JZ4780, Atmel).
- ST:
* Adding support for STM32 FMC2 NAND flash controller.
- Meson:
* Adding support for Amlogic NAND flash controller.
- Denali:
* Several cleanup patches.
- Sunxi:
* Several cleanup patches.
- FSMC:
* Disabling NAND on remove().
* Resetting NAND timings on resume().
SPI-NAND drivers changes:
- Toshiba:
* Adding support for all Toshiba products.
- Macronix:
* Fixing ECC status read.
- Gigadevice:
* Adding support for GD5F1GQ4UExxG.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE9HuaYnbmDhq/XIDIJWrqGEe9VoQFAlxwE4kACgkQJWrqGEe9
VoRQVQf+OOkScM6ZbsO2GbMRe0ybMOCOyBXfojPEGtVv80gHHrAPRocLqWMB1Xdb
MSfm7j+lyZU1I8eYVvdYXby7s5FlVWbrh8NSnnwox1QusdmyBm7vcxc6st15Poy/
/WtjE+Cry49eIx5L/pmmNH3AIqMdvSRTJD7NgOYjo/SIq4GLR+KQEgt1VLp/KyO0
TGeMDIT3Q3+MXVwvUh3YlHUwNJ2jOpjpPW94QxD0mef/b9doUlkvrOdHs3JeGQzX
aiiqWI1nRBmjNs34wp7Dyf3G/feplKyi+IS/ghTiijAgwbWdRI7KxrPtyCUYiint
3XqVgZAF/sfFaKFMIiJBMzoLQB15dQ==
=VbaE
-----END PGP SIGNATURE-----
Merge tag 'nand/for-5.1' of git://git.infradead.org/linux-mtd into mtd/next
NAND core changes:
- Fourth batch of fixes/cleanup to the raw NAND core impacting various
controller drivers (Sunxi, Marvell, MTK, TMIO, OMAP2).
- Checking the return code of nand_reset() and nand_readid_op().
- Removing ->legacy.erase and single_erase().
- Simplifying the locking.
- Several implicit fall through annotations.
Raw NAND controllers drivers changes:
- Fixing various possible object reference leaks (MTK, JZ4780, Atmel).
- ST:
* Adding support for STM32 FMC2 NAND flash controller.
- Meson:
* Adding support for Amlogic NAND flash controller.
- Denali:
* Several cleanup patches.
- Sunxi:
* Several cleanup patches.
- FSMC:
* Disabling NAND on remove().
* Resetting NAND timings on resume().
SPI-NAND drivers changes:
- Toshiba:
* Adding support for all Toshiba products.
- Macronix:
* Fixing ECC status read.
- Gigadevice:
* Adding support for GD5F1GQ4UExxG.
Core changes:
- Add support of octal mode I/O transfer
- Add a bunch of SPI NOR entries to the flash_info table
SPI NOR controller driver changes:
- cadence-quadspi:
* Add support for Octal SPI controller
* write upto 8-bytes data in STIG mode
- mtk-quadspi:
* rename config to a common one
* add SNOR_HWCAPS_READ to spi_nor_hwcaps mask
MAINTAINERS:
- Add Tudor as SPI-NOR co-maintainer
-----BEGIN PGP SIGNATURE-----
iQIcBAABAgAGBQJcblqiAAoJEGXtNgF+CLcA01oQAI8obPo2l+DJrv3X7EcLViwb
7kIGWQjKKXxoA8KZ8t3XRpQIFg/J+TX1OPo75/ZeLIp2ikuvDRBFkX38RudI7lbn
cU1qLZFHcSPFGk8FlcwWmVEErgEGLif8ytCfyqlVFYwysVnam+UAmCvNAn3p3DIg
qkHtyd4gjoOw2lO+3f/UZlBGE/b4GIAO6EKZWpJdEd71eomgT8yqjqcSfBm2LQ3o
cpWsNhXUZMOvAVB3l1R/0O3n3gSuXYll8CrZQZU2rETGTMykfpZ/tLgTUl9WKTlk
RjjiSKaGebhanL1cM2M7kXPSk4Hm8bpvO64yEoMauFITsMvYkyVe2EAHspNmdBV7
SoLHrlk10C56wNKbl2PNOduz7MdawiaFmNy0Pp2EC7eJ9h03YbI/ORhi+oDg2Zhc
5Pdda5yJ/KVpheDA+9AvJtHVzTF8FOAC1qP+fS+IEmwGzG1yQxKjZz4QAH58OfV1
k5+JgExBimMDvtESoYyXQqMPo1FnWhLkRoVg7/tK3jMEPJO8Y/3j6KH8qyXFrDqZ
IiFbI8xQ3uXNFgbtjUWD9Nhd0UZEkCJi+P7niqMvaCcX/Uga7ob54Vvgp3EKDXDT
lp0mUPjnpL5CbL4XW7NUY1Yic3bvtkxBQDR6O4+urTrSwkLxqiqCdDzZCrFIrrPj
gPlsWD3CR4exwd0Ar8sg
=tTBK
-----END PGP SIGNATURE-----
Merge tag 'spi-nor/for-5.1' of git://git.infradead.org/linux-mtd into mtd/next
SPI NOR Changes
Core changes:
- Add support of octal mode I/O transfer
- Add a bunch of SPI NOR entries to the flash_info table
SPI NOR controller driver changes:
- cadence-quadspi:
* Add support for Octal SPI controller
* write upto 8-bytes data in STIG mode
- mtk-quadspi:
* rename config to a common one
* add SNOR_HWCAPS_READ to spi_nor_hwcaps mask
MAINTAINERS:
- Add Tudor as SPI-NOR co-maintainer
Using UBI_IOCRPEB and UBI_IOCSPEB userspace can force
reading and scrubbing of PEBs.
In case of bitflips UBI will automatically take action
and move data to a different PEB.
This interface allows a daemon to foster your NAND.
Signed-off-by: Richard Weinberger <richard@nod.at>
This function works like in_wl_tree() but checks whether an ubi_wl_entry
is currently in the protection queue.
We need this function to query the current state of an ubi_wl_entry.
Signed-off-by: Richard Weinberger <richard@nod.at>
There is a spelling mistake in a dev_error message. Fix it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
The Eon EN25QH64 is a 64 Mbit SPI NOR flash memory chip found
on recent wireless routers. Its 32, 128 and 256 Mbit siblings
are already supported.
Tested on a COMFAST CF-E120A v3 router board.
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
This adds support for the Macronix MX25V8035F, a 8Mb SPI NOR chip.
It is used on i.MX6UL/ULL SoMs by Kontron Electronics GmbH (N631x).
It was only tested with a single data line connected, by writing and
reading random data with dd.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
This adds support for the EON EN25Q80A, a 8Mb SPI NOR chip.
It is used on i.MX6 boards by Kontron Electronics GmbH
(N60xx, N61xx).
It was only tested with a single data line connected, by writing and
reading random data with dd.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
Cadence OSPI controller IP supports Octal IO (x8 IO lines),
It also has an integrated PHY. IP register layout is very
similar to existing QSPI IP except for additional bits to support Octal
and Octal DDR mode. Therefore, extend current driver to support Octal
mode. Only Octal SDR read (1-1-8)mode is supported for now.
Tested with mt35xu512aba Octal flash on TI's AM654 EVM.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
Due to two different versions (S25FL128SAGBHI200 and S25FL128SAGBHI210) of
the s25fl128s qspi memory, the single "s25fl128s" device entry must be
split into two to match the correct JEDEC ID's for each version. Solves
paging related issues of S25FL128SAGBHI210 chips.
Signed-off-by: Ahmet Celenk <ahmet.celenk@procenne.com>
Cc: Boris Brezillon <boris.brezillon@free-electrons.com>
Cc: Marek Vasut <marek.vasut@gmail.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
With this patch, we use the mtd->name instead of concatenating the name
with '0'.
Fixes: c4dfa25ab3 ("mtd: add support for reading MTD devices via the nvmem API")
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
cadence-quadspi controller allows upto eight bytes of data to
be written in software Triggered Instruction generator (STIG) mode
of operation. Lower 4 bytes are written through writedatalower and
upper 4 bytes by writedataupper register.
This patch allows all the 8 bytes to be written.
Signed-off-by: Purna Chandra Mandal <purna.chandra.mandal@intel.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
The mx25u3235f is found on the ZyXEL NBG6817 router, therefore
add driver support for it so that we can upstream board support.
Minimal tested with u-boot tools fw_printenv/fw_setenv on GlobalScale
ESPRESSObin v5 board.
Signed-off-by: André Valentin <avalentin@marcant.net>
[miyatsu@qq.com: Remove unnecessary white space.]
Signed-off-by: Ding Tao <miyatsu@qq.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
Commit 6f1fe97bec ("mtd: rawnand: denali_dt: add more clocks based
on IP datasheet") introduced a more correct binding that requires
three named clocks.
Now that all upstream DT files migrated over to it, remove the single
anonymous clock support.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Tested-by: Dinh Nguyen <dinguyen@kernel.org>
Acked-by: Dinh Nguyen <dinguyen@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
of_find_device_by_node() takes a reference to the struct device
when it finds a match via get_device, there is no need to call
get_device() twice.
We also should make sure to drop the reference to the device
taken by of_find_device_by_node() on driver unbind.
Fixes: 1d6b1e4649 ("mtd: mediatek: driver for MTK Smart Device")
Signed-off-by: Wen Yang <yellowriver2010@hotmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
of_find_device_by_node() takes a reference to the struct device
when it finds a match via get_device, there is no need to call
get_device() twice.
We also should make sure to drop the reference to the device
taken by of_find_device_by_node() on driver unbind.
Fixes: ae02ab00aa ("mtd: nand: jz4780: driver for NAND devices on JZ4780 SoCs")
Signed-off-by: Wen Yang <yellowriver2010@hotmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
of_find_device_by_node() takes a reference to the struct device
when it finds a match via get_device, there is no need to call
get_device() twice.
We also should make sure to drop the reference to the device
taken by of_find_device_by_node() on driver unbind.
Fixes: f88fc122cc ("mtd: nand: Cleanup/rework the atmel_nand driver")
Signed-off-by: Wen Yang <yellowriver2010@hotmail.com>
Suggested-by: Boris Brezillon <bbrezillon@kernel.org>
Reviewed-by: Boris Brezillon <bbrezillon@kernel.org>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Tudor Ambarus <tudor.ambarus@microchip.com>
Cc: Boris Brezillon <bbrezillon@kernel.org>
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Brian Norris <computersforpeace@gmail.com>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Nicolas Ferre <nicolas.ferre@microchip.com>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Ludovic Desroches <ludovic.desroches@microchip.com>
Cc: linux-mtd@lists.infradead.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Disable BCH soft reset according to MX23 erratum #2847 ("BCH soft
reset may cause bus master lock up") for MX28 too. It has the same
problem.
Observed problem: once per 100,000+ MX28 reboots NAND read failed on
DMA timeout errors:
[ 1.770823] UBI: attaching mtd3 to ubi0
[ 2.768088] gpmi_nand: DMA timeout, last DMA :1
[ 3.958087] gpmi_nand: BCH timeout, last DMA :1
[ 4.156033] gpmi_nand: Error in ECC-based read: -110
[ 4.161136] UBI warning: ubi_io_read: error -110 while reading 64
bytes from PEB 0:0, read only 0 bytes, retry
[ 4.171283] step 1 error
[ 4.173846] gpmi_nand: Chip: 0, Error -1
Without BCH soft reset we successfully executed 1,000,000 MX28 reboots.
I have a quote from NXP regarding this problem, from July 18th 2016:
"As the i.MX23 and i.MX28 are of the same generation, they share many
characteristics. Unfortunately, also the erratas may be shared.
In case of the documented erratas and the workarounds, you can also
apply the workaround solution of one device on the other one. This have
been reported, but I’m afraid that there are not an estimated date for
updating the Errata documents.
Please accept our apologies for any inconveniences this may cause."
Fixes: 6f2a6a5256 ("mtd: nand: gpmi: reset BCH earlier, too, to avoid NAND startup problems")
Cc: stable@vger.kernel.org
Signed-off-by: Manfred Schlaegl <manfred.schlaegl@ginzinger.com>
Signed-off-by: Martin Kepplinger <martin.kepplinger@ginzinger.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Acked-by: Han Xu <han.xu@nxp.com>
Signed-off-by: Boris Brezillon <bbrezillon@kernel.org>
Commit 33f45c44d6 ("mtd: Do not allow MTD devices with inconsistent
erase properties") introduced a check to make sure ->erasesize and
->_erase values are consistent with the MTD_NO_ERASE flag.
This patch did not take the 0 bytes partition case into account which
can happen when the defined partition is outside the flash device memory
range. Fix that by setting the partition erasesize to the parent
erasesize.
Fixes: 33f45c44d6 ("mtd: Do not allow MTD devices with inconsistent erase properties")
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: <stable@vger.kernel.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Boris Brezillon <bbrezillon@kernel.org>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
This disables the NAND on remove() and the errorpath,
making sure the chipselect gets deasserted when the
NAND is not in use.
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
When we go through a suspend/resume cycle the NAND
timings and other settings may have been lost so reset
the chip to bring it up in a known working state.
The FSMC only supports single CS chips so we only need
to call nand_reset(chip, 0).
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
This is a leftover of commit 997cde2a22 ("mtd: nand: denali: skip
driver internal bounce buffer when possible").
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
This argument is not used at all.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
This code was added by commit 26d266e10e ("mtd: nand: denali: fix
raw and oob accessors for syndrome page layout"), but I do not see
sensible reason.
The IRQ flags are correctly reset by denali_cmd_ctrl(), so this code
is unneeded.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
nand_scan_ident() iterates over maxchips to find as many homogeneous
chips as possible.
Since commit 2d472aba15 ("mtd: nand: document the NAND
controller/NAND chip DT representation"), new drivers should pass in
the exact number of CS lines instead of possible max, but old
platforms may still rely on nand_scan_ident() to detect the actual
number of connected CS lines.
In that case, this loop bails out when manufacturer or device ID
unmatches. The reason of unmatch is most likely no chip is connected
to that CS line. If so, nand_reset() should already have failed,
and the following nand_readid_op() is pointless.
Before ->exec_op hook was introduced, drivers had no way to tell
the failure of NAND_CMD_RESET to the framework because the legacy
->cmdfunc() has void return type. Now drivers implementing ->exec_op
hook can return the error code. You can save nand_readid_op() by
checking the return value of nand_reset(). The return value of
nand_readid_op() should be checked as well. If it fails, probably
id[0] and id[1] are undefined values.
Just for consistency, it should be sensible to check the return
code in nand_do_write_oob() as well.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Boris Brezillon <bbrezillon@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Now that the last user of this hook, denali.c, stopped using it,
we can remove the erase hook from nand_legacy.
I squashed single_erase() because only the difference between
single_erase() and nand_erase_op() is the number of bit shifts.
The status/ret conversion in nand_erase_nand() is unneeded since
commit eb94555e9e ("mtd: nand: use usual return values for the
->erase() hook"). Cleaned it up now.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Boris Brezillon <bbrezillon@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Commit f9ebd1bb41 ("mtd: rawnand: Deprecate ->erase()") discouraged
the use of this hook, so I am happy to follow the suggestion.
Although the Denali IP provides a special MAP10 command for erasing,
using it would not buy us much. The Denali IP actually works with the
generic erasing by single_erase() + ->cmdfunc hook (nand_command_lp)
+ ->cmd_ctrl hook (denali_cmd_ctrl).
This method is also deprecated, but denali_erase() can go away
irrespective of ->exec_op conversion.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Boris Brezillon <bbrezillon@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
There is a plan to build the kernel with -Wimplicit-fallthrough and
these places in the code produced warnings (W=1).
This commit removes the following warnings:
drivers/mtd/nand/raw/nand_base.c:5556:6: warning: this statement may fall through [-Wimplicit-fallthrough=]
drivers/mtd/nand/raw/nand_base.c:5575:6: warning: this statement may fall through [-Wimplicit-fallthrough=]
drivers/mtd/nand/raw/nand_base.c:5613:13: warning: this statement may fall through [-Wimplicit-fallthrough=]
Signed-off-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
There is a plan to build the kernel with -Wimplicit-fallthrough and
these places in the code produced warnings (W=1).
This commit removes the following warnings:
drivers/mtd/nand/raw/nand_legacy.c:332:6: warning: this statement may fall through [-Wimplicit-fallthrough=]
drivers/mtd/nand/raw/nand_legacy.c:483:3: warning: this statement may fall through [-Wimplicit-fallthrough=]
Signed-off-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Add initial support for the Amlogic NAND flash controller which is
available on Meson SoCs.
Signed-off-by: Liang Yang <liang.yang@amlogic.com>
Signed-off-by: Yixun Lan <yixun.lan@amlogic.com>
Signed-off-by: Jianxin Pan <jianxin.pan@amlogic.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
nand_get_device() was complex for apparently no good reason. Let's
replace this locking scheme with 2 mutexes: one attached to the
controller and another one attached to the chip.
Every time the core calls nand_get_device(), it will first lock the
chip and if the chip is not suspended, will then lock the controller.
nand_release_device() will release both lock in the reverse order.
nand_get_device() can sleep, just like the previous implementation,
which means you should never call that from an atomic context.
We also get rid of
- the chip->state field, since all it was used for was flagging the
chip as suspended. We replace it by a field called chip->suspended
and directly set it from nand_suspend/resume()
- the controller->wq and controller->active fields which are no longer
needed since the new controller->lock (now a mutex) guarantees that
all operations are serialized at the controller level
- panic_nand_get_device() which would anyway be a no-op. Talking about
panic write, I keep thinking the rawnand implementation is unsafe
because there's not negotiation with the controller to know when it's
actually done with it's previous operation. I don't intend to fix
that here, but that's probably something we should look at, or maybe
we should consider dropping the ->_panic_write() implementation
Last important change to mention: we now return -EBUSY when someone
tries to access a device that as been suspended, and propagate this
error to the upper layer.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
We are about to simplify the locking in the rawnand framework, and part
of this simplication is about getting rid of chip->state, so let's
first patch drivers that check the state.
All of them do that to get a timeout value based on the operation that
is being executed. Since a timeout is, by definition, something that
is here to prevent hanging on an event that might never happen,
picking the maximum timeout value no matter the operation should be
harmless.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Stop initializing omap_gpmc_controller fields are declaration time and
replace that by a call to nand_controller_init(). Since the same object
might be shared by several NAND chips and the NAND controller driver
expects a ->probe() per-chip, we need to keep track of the
omap_gpmc_controller state (whether it's already been initialized or
not).
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
nand_controller->wq has never been meant to be used by NAND controller
drivers. This waitqueue is used by the framework to serialize accesses
to a NAND controller, and messing up with its state is a really bad
idea.
Declare a completion object in tmio_nand and use it to wait for RB
transitions.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
nand_controller_init() has been added to simplify nand_controller
struct initialization. Use this function instead of duplicating the
logic.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array. For example:
struct foo {
int stuff;
void *entry[];
};
instance = devm_kzalloc(dev, sizeof(struct foo) + sizeof(void *) * count, GFP_KERNEL);
Instead of leaving these open-coded and prone to type mistakes, we can
now use the new struct_size() helper:
instance = devm_kzalloc(dev, struct_size(instance, entry, count), GFP_KERNEL);
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
In non-EDO, tREA should be less than tRP to guarantee that the
controller does not sample the IO lines too early. Unfortunately, the
sunxi NAND controller does not allow us to have different values for
tRP and tREH (tRP = tREH = tRW / 2).
We have 2 options to overcome this limitation:
1/ Extend tRC to fulfil the tREA <= tRC / 2 constraint
2/ Use EDO mode (only works if timings->tRLOH > 0)
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The datasheet specifies the upper four bits are reserved.
Testing on real hardware shows that these bits can indeed be nonzero.
Signed-off-by: Emil Lenngren <emil.lenngren@gmail.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Fix the struct description and use standard kernel-doc header format
(even if the file is not parsed by the doc generator).
We also replace tabs by a single space.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
And get rif of all legacy hooks and unused fields.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Replace the license text by an SPDX tag and fix MODULE_LICENSE() to
match GPL-2.0+.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Replace them by nand_chip pointers.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
nand_chip objects are sometimes called chip and sometimes nand. Rename
all of them into nand to make things consistent.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Use struct_size() to calculate sunxi_nand object size.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
sunxi_nand_chip objects are sometimes called chip and other times
called sunxi_nand. Make that consistent and name all occurrences
sunxi_nand.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
This patch adds the polling mode, a basic mode that do not need
any DMA channels. This mode is also useful for debug purpose.
Signed-off-by: Christophe Kerello <christophe.kerello@st.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The driver adds the support for the STMicroelectronics FMC2 NAND
Controller found on STM32MP SOCs.
This patch is based on FMC2 command sequencer.
The purpose of the command sequencer is to facilitate the programming
and the reading of NAND flash pages with the ECC and to free the CPU
of sequencing tasks.
It requires one DMA channel for write and two DMA channels for read
operations.
Only NAND_ECC_HW mode is actually supported.
The driver supports a maximum 8k page size.
The following ECC strength and step size are currently supported:
- nand-ecc-strength = <8>, nand-ecc-step-size = <512> (BCH8)
- nand-ecc-strength = <4>, nand-ecc-step-size = <512> (BCH4)
- nand-ecc-strength = <1>, nand-ecc-step-size = <512> (Extended ECC
based on Hamming)
This patch has been tested on Micron MT29F8G08ABACAH4 and
MT29F8G16ABACAH4
Signed-off-by: Christophe Kerello <christophe.kerello@st.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Commit 2b6f0090a3 ("mtd: Check add_mtd_device() ret code") contained
a leftover of the debug session that led to this bug fix. Remove this
pr_info().
Fixes: 2b6f0090a3 ("mtd: Check add_mtd_device() ret code")
Signed-off-by: Boris Brezillon <bbrezillon@kernel.org>
Fix kernel-doc warnings in drivers/mtd/nand/raw:
../drivers/mtd/nand/raw/nand_base.c:420: warning: Function parameter or member 'chip' not described in 'nand_fill_oob'
../drivers/mtd/nand/raw/nand_bbt.c:173: warning: Function parameter or member 'this' not described in 'read_bbt'
../drivers/mtd/nand/raw/nand_bbt.c:173: warning: Excess function parameter 'chip' description in 'read_bbt'
Fixes: 0813621ba8 ("mtd: rawnand: Stop passing mtd_info objects to internal functions")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Boris Brezillon <boris.brezillon@bootlin.com>
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: linux-mtd@lists.infradead.org
Acked-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <bbrezillon@kernel.org>
The manufacturer specific initialization has already been done when
block unlocking takes place, and if anything goes wrong during this
procedure we should call spinand_manufacturer_cleanup().
Fixes: 7529df4652 ("mtd: nand: Add core infrastructure to support SPI NANDs")
Cc: <stable@vger.kernel.org>
Signed-off-by: Boris Brezillon <bbrezillon@kernel.org>
Acked-by: Miquel Raynal <miquel.raynal@bootlin.com>
Looks like PROGRAM LOAD (AKA write cache) does not necessarily reset
the cache content to 0xFF (depends on vendor implementation), so we
must fill the page cache entirely even if we only want to program the
data portion of the page, otherwise we might corrupt the BBM or user
data previously programmed in OOB area.
Fixes: 7529df4652 ("mtd: nand: Add core infrastructure to support SPI NANDs")
Reported-by: Stefan Roese <sr@denx.de>
Cc: <stable@vger.kernel.org>
Signed-off-by: Boris Brezillon <bbrezillon@kernel.org>
Tested-by: Stefan Roese <sr@denx.de>
Reviewed-by: Stefan Roese <sr@denx.de>
Acked-by: Miquel Raynal <miquel.raynal@bootlin.com>
In case DOC_CHIPID_G3, mtd->name is not freed in err handling path,
which is alloced by kasprintf(). Fix this by using devm_kasprintf().
Fixes: ae9d4934b2 ("mtd: docg3: add multiple floor support")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Boris Brezillon <bbrezillon@kernel.org>
Some sysfs functions have empty stray lines after the return statement.
This patch remove those empty lines.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Boris Brezillon <bbrezillon@kernel.org>
Signed-off-by: Boris Brezillon <bbrezillon@kernel.org>
Spansion S25FL512S ID is erroneously using 5-byte JEDEC ID, while the chip
family ID is stored in the 6th byte. Due to using only 5-byte ID, it's also
covering S25FS512S and now that we have added 6-byte ID for that chip, we
can convert S25FL512S to using a proper 6-byte ID as well...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Boris Brezillon <bbrezillon@kernel.org>
Spansion S25FS512S flash is currently misdetected as S25FL512S since the
latter uses 5-byte JEDEC ID, while the 6th ID byte (family ID) is different
on those chips. Add the 6-byte S25FS512S ID before S25FL512S ID in order
not to break the existing S25FS512S users.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Boris Brezillon <bbrezillon@kernel.org>
The function jz_nand_ioremap_resource() needs a pointer to an __iomem
pointer as its last argument but this argument is declared as:
void * __iomem *base
Fix this by using the correct declaration:
void __iomem **base
which then also removes the following Sparse's warnings:
282:15: warning: incorrect type in assignment (different address spaces)
282:15: expected void *[noderef] <asn:2>
282:15: got void [noderef] <asn:2> *
322:57: warning: incorrect type in argument 4 (different address spaces)
322:57: expected void *[noderef] <asn:2> *base
322:57: got void [noderef] <asn:2> **
402:67: warning: incorrect type in argument 4 (different address spaces)
402:67: expected void *[noderef] <asn:2> *base
402:67: got void [noderef] <asn:2> **
Signed-off-by: Luc Van Oostenryck <luc.vanoostenryck@gmail.com>
Acked-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <bbrezillon@kernel.org>
Add support for octal mode I/O data transfer based on the controller (spi)
mode.
Assign hw-capability mask bits for octal transfer.
Signed-off-by: Yogesh Narayan Gaur <yogeshnarayan.gaur@nxp.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Boris Brezillon <bbrezillon@kernel.org>
Add octal read flag for flash mt35xu512aba.
This flash, mt35xu512aba, is only complaint to SFDP JESD216B and does
not seem to support newer JESD216C standard that provides auto
detection of Octal mode capabilities and opcodes. Therefore, this
capability is manually added using new SPI_NOR_OCTAL_READ flag.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Yogesh Narayan Gaur <yogeshnarayan.gaur@nxp.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Boris Brezillon <bbrezillon@kernel.org>
- Add opcodes for octal I/O commands
* Read : 1-1-8 and 1-8-8 protocol
* Write : 1-1-8 and 1-8-8 protocol
* opcodes for 4-byte address mode command
- Entry of macros in _convert_3to4_xxx function
- Add flag SPI_NOR_OCTAL_READ specifying flash support octal read
commands. This flag is required for flashes which didn't provides
support for auto detection of Octal mode capabilities i.e. not
seems to support newer JESD216C standard.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Yogesh Narayan Gaur <yogeshnarayan.gaur@nxp.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Boris Brezillon <bbrezillon@kernel.org>
mtd_{read,write}_oob() already take care of checking the params and
calling ->_{read,write}() or ->_{read,write}_oob() based on the
request and the operations supported by the MTD device.
No need to duplicate the logic, we can simply implement
mtd_{read,write}() as wrappers around mtd_{read,write}_oob().
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <bbrezillon@kernel.org>
The quadspi is a generic communication interface which could be shared
with other MediaTek SoCs. Hence rename it to a common one.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Boris Brezillon <bbrezillon@kernel.org>
SNOR_HWCAPS_READ should be supported by this controller, so add this
flag to spi_nor_hwcaps mask.
Signed-off-by: Guochun Mao <guochun.mao@mediatek.com>
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Boris Brezillon <bbrezillon@kernel.org>
One of the more common cases of allocation size calculations is finding the
size of a structure that has a zero-sized array at the end, along with memory
for some number of elements for that array. For example:
struct foo {
int stuff;
void *entry[];
};
instance = kzalloc(sizeof(struct foo) + sizeof(void *) * count, GFP_KERNEL);
Instead of leaving these open-coded and prone to type mistakes, we can now
use the new struct_size() helper:
instance = kzalloc(struct_size(instance, entry, count), GFP_KERNEL);
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Boris Brezillon <bbrezillon@kernel.org>
One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array. For example:
struct foo {
int stuff;
void *entry[];
};
instance = kmalloc(sizeof(struct foo) + sizeof(void *) * count, GFP_KERNEL);
Instead of leaving these open-coded and prone to type mistakes, we can
now use the new struct_size() helper:
instance = kmalloc(struct_size(instance, entry, count), GFP_KERNEL);
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Boris Brezillon <bbrezillon@kernel.org>
One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array. For example:
struct foo {
int stuff;
void *entry[];
};
instance = kmalloc(sizeof(struct foo) + sizeof(void *) * count, GFP_KERNEL);
Instead of leaving these open-coded and prone to type mistakes, we can
now use the new struct_size() helper:
instance = kmalloc(struct_size(instance, entry, count), GFP_KERNEL);
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Boris Brezillon <bbrezillon@kernel.org>
Hammering the "bank enable" (PBKEN) bit on and off between
every command crashes the Nomadik NHK15 with this message:
Scanning device for bad blocks
Unhandled fault: external abort on non-linefetch (0x008) at 0xcc95e000
pgd = (ptrval)
[cc95e000] *pgd=0b808811, *pte=40000653, *ppte=40000552
Internal error: : 8 [#1] PREEMPT ARM
Modules linked in:
CPU: 0 PID: 1 Comm: swapper Not tainted 4.20.0-rc2+ #72
Hardware name: Nomadik STn8815
PC is at fsmc_exec_op+0x194/0x204
(...)
After a discussion we (me and Boris Brezillon) start to suspect
that this bit does not immediately control the chip select line
at all, it rather enables access to the bank and the hardware
will drive the CS autonomously. If there is a NAND chip connected,
we should keep this enabled.
As fsmc_nand_setup() sets this bit, we can simply remove the
offending code.
Fixes: 550b9fc4e3 ("mtd: rawnand: fsmc: Stop implementing ->select_chip()")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <bbrezillon@kernel.org>
Since we can set module parameters also when a driver is built in,
it makes no sense to protect module parameter with #ifdef MODULE.
Now the mtdram sizes can also set when the module is not a loadable
module.
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Boris Brezillon <bbrezillon@kernel.org>
This patch fixes a memory corruption that occurred in the
qcom-nandc driver since it was converted to nand_scan().
On boot, an affected device will panic from a NPE at a weird place:
| Unable to handle kernel NULL pointer dereference at virtual address 0
| pgd = (ptrval)
| [00000000] *pgd=00000000
| Internal error: Oops: 80000005 [#1] SMP ARM
| CPU: 0 PID: 1 Comm: swapper/0 Not tainted 4.19.9 #0
| Hardware name: Generic DT based system
| PC is at (null)
| LR is at nand_block_isbad+0x90/0xa4
| pc : [<00000000>] lr : [<c0592240>] psr: 80000013
| sp : cf839d40 ip : 00000000 fp : cfae9e20
| r10: cf815810 r9 : 00000000 r8 : 00000000
| r7 : 00000000 r6 : 00000000 r5 : 00000001 r4 : cf815810
| r3 : 00000000 r2 : cfae9810 r1 : ffffffff r0 : cf815810
| Flags: Nzcv IRQs on FIQs on Mode SVC_32 ISA ARM Segment none
| Control: 10c5387d Table: 8020406a DAC: 00000051
| Process swapper/0 (pid: 1, stack limit = 0x(ptrval))
| [<c0592240>] (nand_block_isbad) from [<c0580a94>]
| [<c0580a94>] (allocate_partition) from [<c05811e4>]
| [<c05811e4>] (add_mtd_partitions) from [<c0581164>]
| [<c0581164>] (parse_mtd_partitions) from [<c057def4>]
| [<c057def4>] (mtd_device_parse_register) from [<c059d274>]
| [<c059d274>] (qcom_nandc_probe) from [<c0567f00>]
The problem is that the nand_scan()'s qcom_nand_attach_chip callback
is updating the nandc->max_cwperpage from 1 to 4. This causes the
sg_init_table of clear_bam_transaction() in the driver's
qcom_nandc_block_bad() to memset much more than what was initially
allocated by alloc_bam_transaction().
This patch restores the old behavior by reallocating the shared bam
transaction alloc_bam_transaction() after the chip was identified,
but before mtd_device_parse_register() (which is an alias for
mtd_device_register() - see panic) gets called. This fixes the
corruption and the driver is working again.
Cc: stable@vger.kernel.org
Fixes: 6a3cec64f1 ("mtd: rawnand: qcom: convert driver to nand_scan()")
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Acked-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <bbrezillon@kernel.org>
There's a new driver using the SPI memory interface of the SPI framework
at spi/spi-fsl-qspi.c, which can be used together with m25p80.c to
replace the functionality of this SPI NOR driver.
The new driver is already in use and this code is not compiled anymore,
so let's remove it.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Acked-by: Han Xu <han.xu@nxp.com>
Tested-by: Han Xu <han.xu@nxp.com>
Acked-by: Boris Brezillon <bbrezillon@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This driver is derived from the SPI NOR driver at
mtd/spi-nor/fsl-quadspi.c. It uses the new SPI memory interface
of the SPI framework to issue flash memory operations to up to
four connected flash chips (2 buses with 2 CS each).
The controller does not support generic SPI messages.
This patch also disables the build of the "old" driver and reuses
its Kconfig option CONFIG_SPI_FSL_QUADSPI to replace it.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Acked-by: Han Xu <han.xu@nxp.com>
Reviewed-by: Yogesh Gaur <yogeshnarayan.gaur@nxp.com>
Tested-by: Yogesh Gaur <yogeshnarayan.gaur@nxp.com>
Tested-by: Han Xu <han.xu@nxp.com>
Reviewed-by: Boris Brezillon <bbrezillon@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
add_mtd_device() can fail. We should always check its return value
and gracefully handle the failure case. Fix the call sites where this
not done (in mtdpart.c) and add a __must_check attribute to the
prototype to avoid this kind of mistakes.
Signed-off-by: Boris Brezillon <bbrezillon@kernel.org>
Commit 20167b70c8 ("nvmem: use EOPNOTSUPP instead of ENOSYS") changed
the nvmem_register() ret code from ENOSYS to EOPNOTSUPP when
CONFIG_NVMEM is not enabled, but the check in mtd_nvmem_add() was not
adjusted accordingly.
Cc: Bartosz Golaszewski <brgl@bgdev.pl>
Cc: Alban Bedel <albeu@free.fr>
Fixes: c4dfa25ab3 ("mtd: add support for reading MTD devices via the nvmem API")
Reported-by: kernel test robot <rong.a.chen@intel.com>
Signed-off-by: Boris Brezillon <bbrezillon@kernel.org>
Reviewed-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Boris Brezillon <bbrezillon@kernel.org>
Here is the big set of char and misc driver patches for 4.21-rc1.
Lots of different types of driver things in here, as this tree seems to
be the "collection of various driver subsystems not big enough to have
their own git tree" lately.
Anyway, some highlights of the changes in here:
- binderfs: is it a rule that all driver subsystems will eventually
grow to have their own filesystem? Binder now has one to handle the
use of it in containerized systems. This was discussed at the
Plumbers conference a few months ago and knocked into mergable shape
very fast by Christian Brauner. Who also has signed up to be
another binder maintainer, showing a distinct lack of good judgement :)
- binder updates and fixes
- mei driver updates
- fpga driver updates and additions
- thunderbolt driver updates
- soundwire driver updates
- extcon driver updates
- nvmem driver updates
- hyper-v driver updates
- coresight driver updates
- pvpanic driver additions and reworking for more device support
- lp driver updates. Yes really, it's _finally_ moved to the proper
parallal port driver model, something I never thought I would see
happen. Good stuff.
- other tiny driver updates and fixes.
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXCZCUA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymF9QCgx/Z8Fj1qzGVGrIE4flXOi7pxOrgAoMqJEWtU
ywwL8M9suKDz7cZT9fWQ
=xxr6
-----END PGP SIGNATURE-----
Merge tag 'char-misc-4.21-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver updates from Greg KH:
"Here is the big set of char and misc driver patches for 4.21-rc1.
Lots of different types of driver things in here, as this tree seems
to be the "collection of various driver subsystems not big enough to
have their own git tree" lately.
Anyway, some highlights of the changes in here:
- binderfs: is it a rule that all driver subsystems will eventually
grow to have their own filesystem? Binder now has one to handle the
use of it in containerized systems.
This was discussed at the Plumbers conference a few months ago and
knocked into mergable shape very fast by Christian Brauner. Who
also has signed up to be another binder maintainer, showing a
distinct lack of good judgement :)
- binder updates and fixes
- mei driver updates
- fpga driver updates and additions
- thunderbolt driver updates
- soundwire driver updates
- extcon driver updates
- nvmem driver updates
- hyper-v driver updates
- coresight driver updates
- pvpanic driver additions and reworking for more device support
- lp driver updates. Yes really, it's _finally_ moved to the proper
parallal port driver model, something I never thought I would see
happen. Good stuff.
- other tiny driver updates and fixes.
All of these have been in linux-next for a while with no reported
issues"
* tag 'char-misc-4.21-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (116 commits)
MAINTAINERS: add another Android binder maintainer
intel_th: msu: Fix an off-by-one in attribute store
stm class: Add a reference to the SyS-T document
stm class: Fix a module refcount leak in policy creation error path
char: lp: use new parport device model
char: lp: properly count the lp devices
char: lp: use first unused lp number while registering
char: lp: detach the device when parallel port is removed
char: lp: introduce list to save port number
bus: qcom: remove duplicated include from qcom-ebi2.c
VMCI: Use memdup_user() rather than duplicating its implementation
char/rtc: Use of_node_name_eq for node name comparisons
misc: mic: fix a DMA pool free failure
ptp: fix an IS_ERR() vs NULL check
genwqe: Fix size check
binder: implement binderfs
binder: fix use-after-free due to ksys_close() during fdget()
bus: fsl-mc: remove duplicated include files
bus: fsl-mc: explicitly define the fsl_mc_command endianness
misc: ti-st: make array read_ver_cmd static, shrinks object size
...
Pull Devicetree updates from Rob Herring:
"The biggest highlight here is the start of using json-schema for DT
bindings. Being able to validate bindings has been discussed for years
with little progress.
- Initial support for DT bindings using json-schema language. This is
the start of converting DT bindings from free-form text to a
structured format.
- Reworking of initrd address initialization. This moves to using the
phys address instead of virt addr in the DT parsing code. This
rework was motivated by CONFIG_DEV_BLK_INITRD causing unnecessary
rebuilding of lots of files.
- Fix stale phandle entries in phandle cache
- DT overlay validation improvements. This exposed several memory
leak bugs which have been fixed.
- Use node name and device_type helper functions in DT code
- Last remaining conversions to using %pOFn printk specifier instead
of device_node.name directly
- Create new common RTC binding doc and move all trivial RTC devices
out of trivial-devices.txt.
- New bindings for Freescale MAG3110 magnetometer, Cadence Sierra
PHY, and Xen shared memory
- Update dtc to upstream version v1.4.7-57-gf267e674d145"
* tag 'devicetree-for-4.21' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (68 commits)
of: __of_detach_node() - remove node from phandle cache
of: of_node_get()/of_node_put() nodes held in phandle cache
gpio-omap.txt: add reg and interrupts properties
dt-bindings: mrvl,intc: fix a trivial typo
dt-bindings: iio: magnetometer: add dt-bindings for freescale mag3110
dt-bindings: Convert trivial-devices.txt to json-schema
dt-bindings: arm: mrvl: amend Browstone compatible string
dt-bindings: arm: Convert Tegra board/soc bindings to json-schema
dt-bindings: arm: Convert ZTE board/soc bindings to json-schema
dt-bindings: arm: Add missing Xilinx boards
dt-bindings: arm: Convert Xilinx board/soc bindings to json-schema
dt-bindings: arm: Convert VIA board/soc bindings to json-schema
dt-bindings: arm: Convert ST STi board/soc bindings to json-schema
dt-bindings: arm: Convert SPEAr board/soc bindings to json-schema
dt-bindings: arm: Convert CSR SiRF board/soc bindings to json-schema
dt-bindings: arm: Convert QCom board/soc bindings to json-schema
dt-bindings: arm: Convert TI nspire board/soc bindings to json-schema
dt-bindings: arm: Convert TI davinci board/soc bindings to json-schema
dt-bindings: arm: Convert Calxeda board/soc bindings to json-schema
dt-bindings: arm: Convert Altera board/soc bindings to json-schema
...
The main thing this release has been a lot of work on the integration
with SPI NOR flashes, there's been some specific support for a while for
controller features designed to make them perform better but it's not
worked out as well as hoped so the interface has been redesigned in a
way that will hopefully do better - it's already been adopted by a
number of additional controllers so things are looking good. Otherwise
most of the work has been driver specific:
- Support for better integration with NOR flashes from Boris Brezillon
and Yogesh Narayan Gaur plus usage of it in several drivers.
- A big cleanup of the Rockchip driver from Emil Renner Berthing.
- Lots of performance improvements for bcm2835 from Lukas Wunner.
- Slave mode support for pxa2xx from Lubomir Rintel.
- Support for Macronix MXIC, Mediatek MT7629 and MT8183, NPCM PSPI,
and Renesas r8a77470.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAlwhLBsTHGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0AGvB/9odNqLjVJiG6v0EIKqLyYXMzCYgmrZ
RyBZoqTKoNmXxv0b/Fdsi8VaiJ8x2WIcqLzhpQlg3twOCvXQbgoA+JzQNyHZlZ1u
8cxfFGebVS6r0k14bkmAVR8LSvGlReOZQLC2MvccVc/UAwN0/p5ncN0xUADHvIOW
/Pmx0/e2uCMx1+OMAudlUXQ5IIbnb5/OjvDfR/7tlVo5YKSgkHBJeunOYSaPSNuO
QNf9+kZxvQ8djYbpYqqHWovPF7JSlQAj0WkMJPB/g3R09E/vatSBlCMnETBJWn/L
wogHquLK/vwRaS+MqTSrGsi0ylpqgxmZrbGKcXKF51fim0EvBg7cMqe6
=ZnI3
-----END PGP SIGNATURE-----
Merge tag 'spi-v4.21' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi updates from Mark Brown:
"The main thing this release has been a lot of work on the integration
with SPI NOR flashes, there's been some specific support for a while
for controller features designed to make them perform better but it's
not worked out as well as hoped so the interface has been redesigned
in a way that will hopefully do better - it's already been adopted by
a number of additional controllers so things are looking good.
Otherwise most of the work has been driver specific:
- Support for better integration with NOR flashes from Boris
Brezillon and Yogesh Narayan Gaur plus usage of it in several
drivers.
- A big cleanup of the Rockchip driver from Emil Renner Berthing.
- Lots of performance improvements for bcm2835 from Lukas Wunner.
- Slave mode support for pxa2xx from Lubomir Rintel.
- Support for Macronix MXIC, Mediatek MT7629 and MT8183, NPCM PSPI,
and Renesas r8a77470"
* tag 'spi-v4.21' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (90 commits)
spi: sh-msiof: Reduce the number of times write to and perform the transmission from FIFO
spi: sh-msiof: Add r8a774c0 support
doc: lpspi: Document DT bindings for LPSPI slave mode
spi: lpspi: Let watermark change with send data length
spi: lpspi: Add slave mode support
spi: lpspi: Replace all "master" with "controller"
spi: imx: drop useless member speed_hz from driver data struct
spi: imx: rename config callback and add useful parameters
spi: imx: style fixes
spi: imx: mx51-ecspi: Move some initialisation to prepare_message hook.
spi: imx: add a device specific prepare_message callback
mtd: atmel-quadspi: disallow building on ebsa110
spi: Update NPCM PSPI controller documentation
spi: npcm: Modify pspi send function
spi: Use of_node_name_eq for node name comparisons
spi: dw-mmio: add ACPI support
spi: bcm2835: Synchronize with callback on DMA termination
spi: bcm2835: Speed up FIFO access if fill level is known
spi: bcm2835: Polish transfer of DMA prologue
spi: spi-mem: add support for octal mode I/O data transfer
...
Core changes:
- Parse the 4BAIT SFDP section
- Add a bunch of SPI NOR entries to the flash_info table
- Add the concept of SFDP fixups and use it to fix a bug on MX25L25635F
- A bunch of minor cleanups/comestic changes
NAND changes:
NAND core changes:
- kernel-doc miscellaneous fixes.
- Third batch of fixes/cleanup to the raw NAND core impacting various
controller drivers (ams-delta, marvell, fsmc, denali, tegra, vf610):
* Stopping to pass mtd_info objects to internal functions
* Reorganizing code to avoid forward declarations
* Dropping useless test in nand_legacy_set_defaults()
* Moving nand_exec_op() to internal.h
* Adding nand_[de]select_target() helpers
* Passing the CS line to be selected in struct nand_operation
* Making ->select_chip() optional when ->exec_op() is implemented
* Deprecating the ->select_chip() hook
* Moving the ->exec_op() method to nand_controller_ops
* Moving ->setup_data_interface() to nand_controller_ops
* Deprecating the dummy_controller field
* Fixing JEDEC detection
* Providing a helper for polling GPIO R/B pin
Raw NAND chip drivers changes:
- Macronix:
* Flagging 1.8V AC chips with a broken GET_FEATURES(TIMINGS)
Raw NAND controllers drivers changes:
- Ams-delta:
* Fixing the error path
* SPDX tag added
* May be compiled with COMPILE_TEST=y
* Conversion to ->exec_op() interface
* Dropping .IOADDR_R/W use
* Use GPIO API for data I/O
- Denali:
* Removing denali_reset_banks()
* Removing ->dev_ready() hook
* Including <linux/bits.h> instead of <linux/bitops.h>
* Changes to comply with the above fixes/cleanup done in the core.
- FSMC:
* Adding an SPDX tag to replace the license text
* Making conversion from chip to fsmc consistent
* Fixing unchecked return value in fsmc_read_page_hwecc
* Changes to comply with the above fixes/cleanup done in the core.
- Marvell:
* Preventing timeouts on a loaded machine (fix)
* Changes to comply with the above fixes/cleanup done in the core.
- OMAP2:
* Pass the parent of pdev to dma_request_chan() (fix)
- R852:
* Use generic DMA API
- sh_flctl:
* Converting to SPDX identifiers
- Sunxi:
* Write pageprog related opcodes to the right register: WCMD_SET (fix)
- Tegra:
* Stop implementing ->select_chip()
- VF610:
* Adding an SPDX tag to replace the license text
* Changes to comply with the above fixes/cleanup done in the core.
- Various trivial/spelling/coding style fixes.
SPI-NAND drivers changes:
- Removing the depreacated mt29f_spinand driver from staging.
- Adding support for:
* Toshiba TC58CVG2S0H
* GigaDevice GD5FxGQ4xA
* Winbond W25N01GV
JFFS2 changes:
- Fix a lockdep issue
MTD changes:
- Rework the physmap driver to merge gpio-addr-flash and physmap_of
in it
- Add a new compatible for RedBoot partitions
- Make sub-partitions RW if the parent partition was RO because of a
mis-alignment
- Add pinctrl support to the
- Addition of /* fall-through */ comments where appropriate
- Various minor fixes and cleanups
Other changes:
- Update my email address
-----BEGIN PGP SIGNATURE-----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=myqK
-----END PGP SIGNATURE-----
Merge tag 'mtd/for-4.21' of git://git.infradead.org/linux-mtd
Pull mtd updates from Boris Brezillon:
"SPI NOR Core changes:
- Parse the 4BAIT SFDP section
- Add a bunch of SPI NOR entries to the flash_info table
- Add the concept of SFDP fixups and use it to fix a bug on MX25L25635F
- A bunch of minor cleanups/comestic changes
NAND core changes:
- kernel-doc miscellaneous fixes.
- Third batch of fixes/cleanup to the raw NAND core impacting various
controller drivers (ams-delta, marvell, fsmc, denali, tegra,
vf610):
* Stop to pass mtd_info objects to internal functions
* Reorganize code to avoid forward declarations
* Drop useless test in nand_legacy_set_defaults()
* Move nand_exec_op() to internal.h
* Add nand_[de]select_target() helpers
* Pass the CS line to be selected in struct nand_operation
* Make ->select_chip() optional when ->exec_op() is implemented
* Deprecate the ->select_chip() hook
* Move the ->exec_op() method to nand_controller_ops
* Move ->setup_data_interface() to nand_controller_ops
* Deprecate the dummy_controller field
* Fix JEDEC detection
* Provide a helper for polling GPIO R/B pin
Raw NAND chip drivers changes:
- Macronix:
* Flag 1.8V AC chips with a broken GET_FEATURES(TIMINGS)
Raw NAND controllers drivers changes:
- Ams-delta:
* Fix the error path
* SPDX tag added
* May be compiled with COMPILE_TEST=y
* Conversion to ->exec_op() interface
* Drop .IOADDR_R/W use
* Use GPIO API for data I/O
- Denali:
* Remove denali_reset_banks()
* Remove ->dev_ready() hook
* Include <linux/bits.h> instead of <linux/bitops.h>
* Changes to comply with the above fixes/cleanup done in the core.
- FSMC:
* Add an SPDX tag to replace the license text
* Make conversion from chip to fsmc consistent
* Fix unchecked return value in fsmc_read_page_hwecc
* Changes to comply with the above fixes/cleanup done in the core.
- Marvell:
* Prevent timeouts on a loaded machine (fix)
* Changes to comply with the above fixes/cleanup done in the core.
- OMAP2:
* Pass the parent of pdev to dma_request_chan() (fix)
- R852:
* Use generic DMA API
- sh_flctl:
* Convert to SPDX identifiers
- Sunxi:
* Write pageprog related opcodes to the right register: WCMD_SET (fix)
- Tegra:
* Stop implementing ->select_chip()
- VF610:
* Add an SPDX tag to replace the license text
* Changes to comply with the above fixes/cleanup done in the core.
- Various trivial/spelling/coding style fixes.
SPI-NAND drivers changes:
- Remove the depreacated mt29f_spinand driver from staging.
- Add support for:
* Toshiba TC58CVG2S0H
* GigaDevice GD5FxGQ4xA
* Winbond W25N01GV
JFFS2 changes:
- Fix a lockdep issue
MTD changes:
- Rework the physmap driver to merge gpio-addr-flash and physmap_of
in it
- Add a new compatible for RedBoot partitions
- Make sub-partitions RW if the parent partition was RO because of a
mis-alignment
- Add pinctrl support to the
- Addition of /* fall-through */ comments where appropriate
- Various minor fixes and cleanups
Other changes:
- Update my email address"
* tag 'mtd/for-4.21' of git://git.infradead.org/linux-mtd: (108 commits)
mtd: rawnand: sunxi: Write pageprog related opcodes to WCMD_SET
MAINTAINERS: Update my email address
mtd: rawnand: marvell: prevent timeouts on a loaded machine
mtd: rawnand: omap2: Pass the parent of pdev to dma_request_chan()
mtd: rawnand: Fix JEDEC detection
mtd: spi-nor: Add support for is25lp016d
mtd: spi-nor: parse SFDP 4-byte Address Instruction Table
mtd: spi-nor: Add 4B_OPCODES flag to is25lp256
mtd: spi-nor: Add an SPDX tag to spi-nor.{c,h}
mtd: spi-nor: Make the enable argument passed to set_byte() a bool
mtd: spi-nor: Stop passing flash_info around
mtd: spi-nor: Avoid forward declaration of internal functions
mtd: spi-nor: Drop inline on all internal helpers
mtd: spi-nor: Add a post BFPT fixup for MX25L25635E
mtd: spi-nor: Add a post BFPT parsing fixup hook
mtd: spi-nor: Add the SNOR_F_4B_OPCODES flag
mtd: spi-nor: cast to u64 to avoid uint overflows
mtd: spi-nor: Add support for IS25LP032/064
mtd: spi-nor: add entry for mt35xu512aba flash
mtd: spi-nor: add macros related to MICRON flash
...
- Parse the 4BAIT SFDP section
- Add a bunch of SPI NOR entries to the flash_info table
- Add the concept of SFDP fixups and use it to fix a bug on MX25L25635F
- A bunch of minor cleanups/comestic changes
-----BEGIN PGP SIGNATURE-----
iQJQBAABCgA6FiEEKmCqpbOU668PNA69Ze02AX4ItwAFAlwVQUYcHGJvcmlzLmJy
ZXppbGxvbkBib290bGluLmNvbQAKCRBl7TYBfgi3ACIYD/sG0+vRIKK8+NgNUHYy
nzKICKvdnBrm2RWi+6va5n2pYggyNy1VhWEjmqWLupjxn7NGkjZiBilhfj8Iv6YN
HScNy7FLHM6pxTKpsZKQLLGKvaUXODgvZwiw3L6T5T3JaJ5nlpE5g8jQy8sCzfjK
pwKdrOw17caZgoY0bMe2ppCObIDLd+mY+WSHbo6tb4/fohpTX1l9QZYHjfgHU9vP
CG0z3sU0JCNGXsbQMngfeuyXFjJ4OKdnklbVTeZl673AYtQMBhQEIGNVkVefuBP3
p8hU0CWRn0Yikc1HGTENvYCnQ7ju3z+16rnLxy3A5CPHhCDrTgUmM8HabYbh+0Si
0Y1wXpEOZ0OZQ7uMs2Q8SK0GLyxqdxkE0ibHgb7K/aLb+yg8oB7DB4Uenb06CiaQ
KAZWGgWZlSondX+/GI7YcQozslFFCfixAw6H0kCpQW0/2piXNqsN5BOROEqjueXW
xeMG0DNnzrQ6/vB9ukLESSB/YvVwfUvt6GSjqMSDdXwx6zyKSvHJ+chCxlK46+Hm
zIVcvNT3mpwcuVnQOZZeCaiIrDUAySEq/8Ztp9O5/CfkzdQyMWxDPoY9A0HjL2p3
FmRN7aAB9jJcdHc2tLwcKPRepjliIUMLf0NXdTSizzQz8WJqULZRBN0VWW4sCbLc
+tTisYjX8fYUz9+kHUcQ4XY16g==
=JXhP
-----END PGP SIGNATURE-----
Merge tag 'spi-nor/for-4.21' of git://git.infradead.org/linux-mtd into mtd/next
Core changes:
- Parse the 4BAIT SFDP section
- Add a bunch of SPI NOR entries to the flash_info table
- Add the concept of SFDP fixups and use it to fix a bug on MX25L25635F
- A bunch of minor cleanups/comestic changes
NAND core changes:
- kernel-doc miscellaneous fixes.
- Third batch of fixes/cleanup to the raw NAND core impacting various
controller drivers (ams-delta, marvell, fsmc, denali, tegra, vf610):
* Stopping to pass mtd_info objects to internal functions
* Reorganizing code to avoid forward declarations
* Dropping useless test in nand_legacy_set_defaults()
* Moving nand_exec_op() to internal.h
* Adding nand_[de]select_target() helpers
* Passing the CS line to be selected in struct nand_operation
* Making ->select_chip() optional when ->exec_op() is implemented
* Deprecating the ->select_chip() hook
* Moving the ->exec_op() method to nand_controller_ops
* Moving ->setup_data_interface() to nand_controller_ops
* Deprecating the dummy_controller field
* Fixing JEDEC detection
* Providing a helper for polling GPIO R/B pin
Raw NAND chip drivers changes:
- Macronix:
* Flagging 1.8V AC chips with a broken GET_FEATURES(TIMINGS)
Raw NAND controllers drivers changes:
- Ams-delta:
* Fixing the error path
* SPDX tag added
* May be compiled with COMPILE_TEST=y
* Conversion to ->exec_op() interface
* Dropping .IOADDR_R/W use
* Use GPIO API for data I/O
- Denali:
* Removing denali_reset_banks()
* Removing ->dev_ready() hook
* Including <linux/bits.h> instead of <linux/bitops.h>
* Changes to comply with the above fixes/cleanup done in the core.
- FSMC:
* Adding an SPDX tag to replace the license text
* Making conversion from chip to fsmc consistent
* Fixing unchecked return value in fsmc_read_page_hwecc
* Changes to comply with the above fixes/cleanup done in the core.
- Marvell:
* Preventing timeouts on a loaded machine (fix)
* Changes to comply with the above fixes/cleanup done in the core.
- OMAP2:
* Pass the parent of pdev to dma_request_chan() (fix)
- R852:
* Use generic DMA API
- sh_flctl:
* Converting to SPDX identifiers
- Sunxi:
* Write pageprog related opcodes to the right register: WCMD_SET (fix)
- Tegra:
* Stop implementing ->select_chip()
- VF610:
* Adding an SPDX tag to replace the license text
* Changes to comply with the above fixes/cleanup done in the core.
- Various trivial/spelling/coding style fixes.
SPI-NAND drivers changes:
- Removing the depreacated mt29f_spinand driver from staging.
- Adding support for:
* Toshiba TC58CVG2S0H
* GigaDevice GD5FxGQ4xA
* Winbond W25N01GV
The opcodes used by the controller when doing batched page prog should
be written in NFC_REG_WCMD_SET not FC_REG_RCMD_SET. Luckily, the
default NFC_REG_WCMD_SET value matches the one we set in the driver
which explains why we didn't notice the problem.
Fixes: 614049a8d9 ("mtd: nand: sunxi: add support for DMA assisted operations")
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
marvell_nfc_wait_op() waits for completion during 'timeout_ms'
milliseconds before throwing an error. While the logic is fine, the
value of 'timeout_ms' is given by the core and actually correspond to
the maximum time the NAND chip will take to complete the
operation. Assuming there is no overhead in the propagation of the
interrupt signal to the the NAND controller (through the Ready/Busy
line), this delay does not take into account the latency of the
operating system. For instance, for a page write, the delay given by
the core is rounded up to 1ms. Hence, when the machine is over loaded,
there is chances that this timeout will be reached.
There are two ways to solve this issue that are not incompatible:
1/ Enlarge the timeout value (if so, how much?).
2/ Check after the waiting method if we did not miss any interrupt
because of the OS latency (an interrupt is still pending). In this
case, we assume the operation exited successfully.
We choose the second approach that is a must in all cases, with the
possibility to also modify the timeout value to be, e.g. at least 1
second in all cases.
Fixes: 02f26ecf8c ("mtd: nand: add reworked Marvell NAND controller driver")
Cc: stable@vger.kernel.org
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Commit e1e6255c31 ("mtd: rawnand: omap2: convert driver to
nand_scan()") moved part of the init code in the ->attach_chip hook
and at the same time changed the struct device object passed to
dma_request_chan() (&pdev->dev instead of pdev->dev.parent).
Fixes: e1e6255c31 ("mtd: rawnand: omap2: convert driver to nand_scan()")
Reported-by: Alexander Sverdlin <alexander.sverdlin@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Tested-by: Alexander Sverdlin <alexander.sverdlin@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
nand_jedec_detect() should return 1 when the PARAM page parsing
succeeds, otherwise the core considers JEDEC detection failed and falls
back to ID-based detection.
Fixes: 480139d922 ("mtd: rawnand: get rid of the JEDEC parameter page in nand_chip")
Cc: <stable@vger.kernel.org>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Acked-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The UBI device reference is dropped but then the device is used as a
parameter of ubi_err. The bug is introduced in changing ubi_err's
behavior. The old ubi_err does not require a UBI device as its first
parameter, but the new one does.
Fixes: 3260870331 ("UBI: Extend UBI layer debug/messaging capabilities")
Signed-off-by: Pan Bian <bianpan2016@163.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
The MTD device reference is dropped via put_mtd_device, however its
field ->index is read and passed to ubi_msg. To fix this, the patch
moves the reference dropping after calling ubi_msg.
Signed-off-by: Pan Bian <bianpan2016@163.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
The is25lp016d is found on the iwg23s from iWave, therefore
add driver support for it so that we can upstream board support.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Add support for SFDP (JESD216B) 4-byte Address Instruction Table. This
table is optional but when available, we parse it to get the 4-byte
address op codes supported by the memory.
Using these op codes is stateless as opposed to entering the 4-byte
address mode or setting the Base Address Register (BAR).
Flashes that have the 4BAIT table declared can now support
SPINOR_OP_PP_1_1_4_4B and SPINOR_OP_PP_1_4_4_4B opcodes.
Tested on MX25L25673G.
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@microchip.com>
[tudor.ambarus@microchip.com:
- rework erase and page program logic,
- pass DMA-able buffer to spi_nor_read_sfdp(),
- introduce SPI_NOR_HAS_4BAIT
- various minor updates.]
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
The is25lp256 supports 4-byte opcodes and quad output.
Suggested-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Liu Xiang <liu.xiang6@zte.com.cn>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Add SPDX tags to replace the license boiler-plate and fix the
MODULE_LICENSE() definition in spi-nor.c to match the license text
(GPL v2).
Interestingly, spi-nor.h and spi-nor.c do not use the same license
(GPL v2+ for spi-nor.h, GPL v2 for spi-nor.c).
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
No need to use an integer when the value is either true or false.
Make it a boolean.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Some functions called from spi_nor_scan() need a flash_info object.
Let's assign nor->info early on to avoid passing info as an extra
argument to each of these sub-functions.
We also stop passing a flash_info object to set_4byte() and use
nor->info directly.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reorganize the code to kill forward declarations of spi_nor_match_id()
macronix_quad_enable() and spi_nor_hwcaps_read2cmd().
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
gcc should be smart enough to decide when inlining a function makes
sense. Drop all inline specifiers.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
MX25L25635F and MX25L25635E share the same JEDEC-ID, but the F variant
supports 4-byte opcodes while the E variant doesn't. We need a way to
differentiate those 2 chips and set the SNOR_F_4B_OPCODES flag only for
the F variant.
Luckily, 4-byte opcode support is not the only difference: Fast Read
4-4-4 is only supported by the F variant, and this feature is
advertised in the BFPT table. Use this to decide when to set the
SNOR_F_4B_OPCODES flag.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Experience has proven that SFDP tables are sometimes wrong, and parsing
of these broken tables can lead to erroneous flash config.
This leaves us 2 options:
1/ set the SPI_NOR_SKIP_SFDP flag and completely ignore SFDP parsing
2/ fix things at runtime
While #1 should always work, it might imply extra work if most of the
SFDP is correct. #2 has the benefit of keeping the generic SFDP parsing
logic almost untouched while allowing SPI NOR manufacturer drivers to
fix the broken bits.
Add a spi_nor_fixups struct where we'll put all our fixup hooks, each
of them being called at a different point in the scan process.
We start a hook called just after the BFPT parsing to allow fixing up
info extracted from the BFPT section. More hooks will be added if other
sections need to be fixed.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Some flash_info entries have the SPI_NOR_4B_OPCODES flag set to let the
core know that the flash supports 4B opcode. While this solution works
fine for id-based caps detection, it doesn't work that well when relying
on SFDP-based caps detection. Let's add an SNOR_F_4B_OPCODES flag so
that the SFDP parsing code can set it when appropriate.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
The "params->size" is defined as "u64".
And "info->sector_size" and "info->n_sectors" are defined as
unsigned int and u16.
Thus, u64 data might have strange data(loss data) if the result
overflows an unsigned int.
This patch casts "info->sector_size" to an u64.
Signed-off-by: huijin.park <huijin.park@samsung.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
The datasheet is publically available at
http://www.issi.com/WW/pdf/IS25LP032-064-128.pdf. The parameters fit to
what is already available for IS25LP128/256.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Add entry for mt35xu512aba Micron NOR flash.
This flash is having uniform sector erase size of 128KB, have
support of FSR(flag status register), flash size is 64MB and
supports 4-byte commands.
Signed-off-by: Yogesh Gaur <yogeshnarayan.gaur@nxp.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Some MICRON related macros in spi-nor domain were ST.
Rename entries related to STMicroelectronics under macro SNOR_MFR_ST.
Added entry of MFR Id for Micron flashes, 0x002C.
Signed-off-by: Yogesh Gaur <yogeshnarayan.gaur@nxp.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
gcc 7 with -Wimplicit-fallthrough raises:
drivers/mtd/spi-nor/spi-nor.c: In function ‘set_4byte’:
drivers/mtd/spi-nor/spi-nor.c:289:13: warning: this statement may fall through [-Wimplicit-fallthrough=]
need_wren = true;
~~~~~~~~~~^~~~~~
drivers/mtd/spi-nor/spi-nor.c:290:2: note: here
case SNOR_MFR_MACRONIX:
^~~~
Quiet the warning by marking the expected switch fall through.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
This chip supports dual and quad read and uniform 4K-byte erase.
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Datasheet:
http://www.winbond.com/resource-files/w25q128jv%20revf%2003272018%20plus.pdf
Testing done on Mikrotik Routerboard wAP R board.
It does not support Dual or Quad modes.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
The entire smpt array is initialized with data read from sfdp,
there is no need to init it with zeroes before.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
There is a plan to build the kernel with -Wimplicit-fallthrough and
these places in the code produced warnings. Fix them up.
Signed-off-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
We try to force NAND controller drivers to properly separate the NAND
controller object from the NAND chip one, so let's deprecate the dummy
controller object embedded in nand_chip to encourage them to create
their own instance.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Replace the license text by an SPDX tag.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The dummy controller is kept around to support old drivers. Let's
patch this one and declare our own nand_controller instance.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Mimic what has been done in the core and avoid passing mtd_info object
internally.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
checkpatch reports a bunch of coding style issues. Let's fix them
all in one step.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Add an SPDX GPL-2.0 tag and update MODULE_LICENSE() to match the
license text.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The dummy controller is kept around to support old drivers. Let's
patch this one and declare our own nand_controller instance.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
nand_to_fsmc() is used almost everywhere except in
fsmc_setup_data_interface() where nand_get_controller_data() is used
instead. Make that consistent and drop the nand_set_controller_data()
call in the probe path.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The kernel-doc describing struct fsmc_nand_data is not in sync with
the struct itself. Add missing entries and drop invalid ones.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Mimic what has been done in the core and stop passing mtd_info
objects to internal functions.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
In nand_scan_ident(), the controller driver resets every NAND chip.
This is done by sending NAND_CMD_RESET. The Denali IP provides
another way to do the equivalent thing; if a bit is set in the
DEVICE_RESET register, the controller sends the RESET command to
the corresponding device. denali_reset_banks() uses it to reset
all devices beforehand.
This redundant reset sequence was needed to know the actual number
of chips before calling nand_scan_ident(); if DEVICE_RESET fails,
there is no chip in that chip select. Then, denali_reset_banks()
sets denali->max_banks to the number of detected chips.
As commit f486287d23 ("mtd: nand: denali: fix bank reset function
to detect the number of chips") explained, nand_scan_ident() issued
Set Features (0xEF) command to all CS lines, some of which may not be
connected with a chip. Then, the driver would wait for R/B# response,
which never happens.
This problem was solved by commit 107b7d6a7a ("mtd: rawnand: avoid
setting again the timings to mode 0 after a reset"). In the current
code, nand_setup_data_interface() is called from nand_scan_tail(),
which is invoked after the chip detection.
Now, we can really remove the redundant denali_nand_banks() by simply
passing the maximum number of chip selects supported by this IP
(typically 4 or 8) to nand_scan(). Let's leave all the chip detection
process to nand_scan_ident().
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The Denali NAND IP has no way to read out the current signal level
of the R/B# pin. Instead, denali_dev_ready() checks if the R/B#
transition has already happened. (The INTR__INT_ACT interrupt is
asserted at the rising edge of the R/B# pin.) It is not a correct
way to implement the ->dev_ready() hook.
In fact, it has a drawback; in the nand_scan_ident phase, the chip
detection iterates over maxchips until it fails to find a homogeneous
chip. For the last loop, nand_reset() fails if no chip is there.
If ->dev_ready hook exists, nand_command(_lp) calls nand_wait_ready()
after NAND_CMD_RESET. However, we know denali_dev_ready() never
returns 1 unless there exists a chip that toggles R/B# in that chip
select. Then, nand_wait_ready() just ends up with wasting 400 msec,
in the end, shows the "timeout while waiting for chip to become ready"
warning.
Let's remove the mis-implemented dev_ready hook, and fallback to
sending the NAND_CMD_STATUS and nand_wait_status_ready(), which
bails out more quickly.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Don't readw()/writew() data directly from/to GPIO port which is under
control of gpio-omap driver, use GPIO consumer API instead.
The driver should now work with any 8-bit bidirectional GPIO port, not
only OMAP.
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Data port used by the driver is actually an OMAP MPUIO device, already
under control of gpio-omap driver. For that reason we used to not
request the memory region of the port as that would fail because the
region is already busy. Despite that, we are still accessing the port
by just ioremapping it and performing read/write operations. Moreover,
we are doing that without any proteciton from other users legally
manipulating the port pins over GPIO API.
The plan is to convert the driver to access the port over GPIO consumer
API. Before that happens, already prevent from other users accessing
the port pins by requesting an array of its GPIO descriptors.
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
->setup_data_interface() is a controller specific method and should
thus be placed in nand_controller_ops.
In order to make that work with controllers that support keeping
pre-configured timings we need to add a new NAND_KEEP_TIMINGS flag to
inform the core it should skip the timings selection step.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Tested-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
->exec_op() is a controller method and has nothing to do in the
nand_chip struct. Let's move it to the nand_controller_ops struct and
adjust the core and drivers accordingly.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Tested-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Now that the CS line to be selected is passed to ->exec_op() and
stored in chip->cur_cs and after patching all drivers implementing
->exec_op() to stop implementing this method, we can deprecate it by
moving it to the nand_legacy structure.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Tested-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Now that the CS to be selected is passed in nand_operation->cs, we can
get rid of the ->select_chip() implementation and replace it by an
internal function which is called from the chip->exec_op() hook.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Tested-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Now that the CS to be selected is kept in chip->cur_cs and passed
in nand_operation->cs, we can get rid of the ->select_chip()
implementation and replace it by an internal function which is called
from the chip->exec_op() and chip->ecc.read/write_xxx() hooks.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Now that the CS to be selected is kept in chip->cur_cs and passed
in nand_operation->cs, we can get rid of the ->select_chip()
implementation and replace it by an internal function which is called
from the chip->exec_op() and chip->ecc.read/write_xxx() hooks.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Now that the CS to be selected is kept in chip->cur_cs and passed
in nand_operation->cs, we can get rid of the ->select_chip()
implementation and replace it by an internal function which is called
from the chip->exec_op() and chip->ecc.read/write_xxx() hooks.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Now that the CS line to assert is directly passed through the
nand_operation struct we can replace the fsmc_select_chip()
implementation by an internal fsmc_ce_ctrl() function which is
directly called from fsmc_exec_op()
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Now that the CS to be selected on a nand_operation is passed in
nand_operation->cs we can make the ->select_chip() hook optional for
drivers implementing ->exec_op().
When not implemented, the core is assuming the CS line is automatically
asserted/deasserted by the driver ->exec_op() implementation.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Tested-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
In order to deprecate the ->select_chip hook we need to pass the CS
line a NAND operations are targeting. This is done through the
addition of a cs field to the nand_operation struct.
We also need to keep track of the currently selected target to
properly initialize op->cs, hence the ->cur_cs field addition to the
nand_chip struct.
Note that op->cs is not assigned in nand_exec_op() because we might
rework the way we execute NAND operations in the future (adopt a
queuing mechanism instead of the serialization we have right now).
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Tested-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Add a wrapper to prevent drivers and core code from directly calling
the ->select_chip hook which we are about to deprecate.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Tested-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
All NAND objects are supposed to inherit from nand_controller. The
framework is providing a dummy controller object, but we're moving
away from this approach in favor of explicit inheritance.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Tested-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
mtd_device_register() can fail, and when it does we should propagate
the error and cleanup what has been done before.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Tested-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Remove unused labels, rename out_mtd into err_unmap to make it clearer
and return 0 instead of using a goto out at the end of the registration
procedure.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Tested-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Most of them were reported by checkpatch:
* s/u_char/u8/
* remove unneeded blank lines
* don't print warning messages when devm_kzalloc() fails
* Use ! instead of == NULL
* Remove invalid comment
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Tested-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Add an SPDX GPL-2.0 tag and update MODULE_LICENSE() to match the
license text.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Drop the asm and mach headers inclusion and allow this driver to be
compiled when COMPILE_TEST=y in order to increase compile-test
coverage.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Tested-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
nand_exec_op() is only used by core code (nand_xxx.c files). Let's
move this inline function in drivers/mtd/nand/raw/internals.h.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Tested-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
nand_legacy_set_defaults() returns directly if chip->exec_op != NULL,
no need to test !chip->exec_op after that.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Tested-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Avoid forward declaration of nand_get_device(), nand_do_write_oob()
and nand_update_bbt() by moving functions around.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Tested-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
After having reworked the rawnand API to avoid passing mtd_info
objects around, let's do the same for internal functions.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Tested-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Gustavo A. R. Silva