Add support for GD25Q256, a 32MiB SPI Nor flash
from GigaDevice.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@wedev4u.fr>
Some manufacturers may use different bit to set QE on different
memories.
The GD25Q256 from GigaDevice is an example, which uses S6(bit 6
of the Status Register-1) to set QE, which is different with
other supported memories from GigaDevice that use S9(bit 1 of
the Status Register-2). This makes it is impossible to select
the quad enable method by distinguishing the MFR. This patch
introduce a quad_enable function which can be set per memory
in the flash_info list table.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@wedev4u.fr>
Allow ARM64 support for the Cadence QSPI interface by
adding ARM64 as a dependency.
Signed-off-by: Thor Thayer <thor.thayer@linux.intel.com>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@wedev4u.fr>
Implemented and populated spi-nor mtd PM handlers for resume ops.
spi-nor resume op re-initializes spi-nor flash to its probed
state by calling the newly implemented spi_nor_init() function.
Signed-off-by: Kamal Dasu <kdasu.kdev@gmail.com>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@wedev4u.fr>
This patch extracts some chunks from spi_nor_init_params and spi_nor_scan()
and moves them into a new spi_nor_init() function.
Indeed, spi_nor_init() regroups all the required SPI flash commands to be
sent to the SPI flash memory before performing any runtime operations
(Fast Read, Page Program, Sector Erase, ...). Hence spi_nor_init():
1) removes the flash protection if applicable for certain vendors.
2) sets the Quad Enable bit, if needed, before using Quad SPI protocols.
3) makes the memory enter its (stateful) 4-byte address mode, if needed,
for SPI flash memory > 128Mbits not supporting the 4-byte address
instruction set.
spi_nor_scan() now ends by calling spi_nor_init() once the probe phase has
completed. Further patches could also use spi_nor_init() to implement the
mtd->_resume() handler for the spi-nor framework.
Signed-off-by: Kamal Dasu <kdasu.kdev@gmail.com>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@wedev4u.fr>
header.minor is of type u8 and cannot be negative.
Detected by CoverityScan CID#1417858 ("Integer handling issues")
Fixes: f384b352cb ("mtd: spi-nor: parse Serial Flash Discoverable
Parameters (SFDP) tables")
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@wedev4u.fr>
spi_nor_read_sfdp() calls nor->read() to read the SFDP data.
When the m25p80 driver is used (pretty common case), nor->read() is then
implemented by the m25p80_read() function, which is likely to initialize a
'struct spi_transfer' from its buf argument before appending this
structure inside the 'struct spi_message' argument of spi_sync().
Besides the SPI sub-system states that both .tx_buf and .rx_buf members of
'struct spi_transfer' must point into dma-safe memory. However, two of the
three calls of spi_nor_read_sfdp() were given pointers to stack allocated
memory as buf argument, hence not in a dma-safe area.
Hopefully, the third and last call of spi_nor_read_sfdp() was already
given a kmalloc'ed buffer argument, hence dma-safe.
So this patch fixes this issue by introducing a
spi_nor_read_sfdp_dma_unsafe() function which simply wraps the existing
spi_nor_read_sfdp() function and uses some kmalloc'ed memory as a bounce
buffer.
Fixes: f384b352cb ("mtd: spi-nor: parse Serial Flash Discoverable Parameters (SFDP) tables")
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@wedev4u.fr>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
One field of the flash parameter table contains information about the
flash device size.
Most of the time the data extracted from this field is valid, but
sometimes the BFPT section of the SFDP table is corrupted or invalid and
this field is set to 0xffffffff, thus resulting in an integer overflow
when setting params->size.
Since NOR devices are anayway always smaller than 2^64 bytes, we can
easily stop the BFPT parsing if the size reported in this table is
invalid.
Fixes: f384b352cb ("mtd: spi-nor: parse Serial Flash Discoverable Parameters (SFDP) tables")
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Cyrille Pitchen <cyrille.pitchen@wedev4u.com>
- add support to the JEDEC JESD216B specification (SFDP tables).
- add support to the Intel Denverton SPI flash controller.
- fix error recovery for Spansion/Cypress SPI NOR memories.
- fix 4-byte address management for the Aspeed SPI controller.
- add support to some Microchip SST26 memory parts
- remove unneeded pinctrl header
-----BEGIN PGP SIGNATURE-----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=A8bR
-----END PGP SIGNATURE-----
Merge tag 'spi-nor/for-4.14' of git://git.infradead.org/l2-mtd into mtd/next
From Cyrille:
"
This pull request contains the following notable changes:
- add support to the JEDEC JESD216B specification (SFDP tables).
- add support to the Intel Denverton SPI flash controller.
- fix error recovery for Spansion/Cypress SPI NOR memories.
- fix 4-byte address management for the Aspeed SPI controller.
- add support to some Microchip SST26 memory parts
- remove unneeded pinctrl header
"
Now that we have a custom printf format specifier, convert users of
full_name to use %pOF instead. This is preparation to remove storing
of the full path string for each node.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Brian Norris <computersforpeace@gmail.com>
Cc: Boris Brezillon <boris.brezillon@free-electrons.com>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Cyrille Pitchen <cyrille.pitchen@wedev4u.fr>
Cc: linux-mtd@lists.infradead.org
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Add a newline to the end of drivers/spi-nor/Makefile to get rid the message,
"No newline at end of file", produced by git. This fix will allow subsequent
changes to the file to be able to produce clean patches.
Signed-off-by: Matthew Gerlach <matthew.gerlach@linux.intel.com>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@wedev4u.fr>
The driver made the wrong assumption that the 4B setting was
autodetected for all chips of the AST2500 FMC flash controller. This
is only the case for the CS0.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@wedev4u.fr>
There is no need to include <linux/pinctrl/consumer.h> as no pinctrl
function is used in this driver, so just remove it.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@wedev4u.fr>
There is no need to include <linux/pinctrl/consumer.h> as no pinctrl
function is used in this driver, so just remove it.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@wedev4u.fr>
S25FL{128|256|512}S datasheets say:
"When P_ERR or E_ERR bits are set to one, the WIP bit will remain set to
one indicating the device remains busy and unable to receive new operation
commands. A Clear Status Register (CLSR) command must be received to return
the device to standby mode."
Current spi-nor code works until first error occurs, but write/erase errors
are not just rare hardware failures, they also occur if user tries to flash
write-protected areas. After such attempt no SPI command can be executed
any more and even read fails. This patch adds support for P_ERR and E_ERR
bits in Status Register 1 (so that operation fails immediately and not
after a long timeout) and proper recovery from the error condition.
Tested on Spansion S25FS128S, which is supported by S25FL129P entry.
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@wedev4u.fr>
Intel Denverton exposes the SPI serial flash controller as a PCI device
instead of being part of the LPC chip as previous generations did.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@free-electrons.com>
This patch adds support to the JESD216 rev B standard and parses the SFDP
tables to dynamically initialize the 'struct spi_nor_flash_parameter'.
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@microchip.com>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
The variable was already marked 'const' before the previous
patch, but the qualifier was in an unusual place, and now the
extra 'const' causes a harmless warning:
drivers/mtd/spi-nor/cadence-quadspi.c:1286:34: error: duplicate 'const' declaration specifier [-Werror=duplicate-decl-specifier]
This removes the other 'const' instead.
Fixes: f993c123b4 ("mtd: spi-nor: cqspi: make of_device_ids const")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@wedev4u.fr>
The segment registers of the SMC controller provide a way to configure
the mapping windows of the chips on the AHB bus. The settings are
required to be correct when the controller operates in Command mode,
which is the case for DMAs and the LPC mapping.
This tries to set the segment registers of each chip depending on the
size of the flash device and depending on the previous segment
settings, in order to have a contiguous window across multiple chips.
Unfortunately, the AST2500 SPI controller has a bug and it is not
possible to configure a full 128MB window for a chip of the same
size. The window size needs to be restricted to 120MB. This issue only
applies to CE0.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@wedev4u.fr>
There is no need to keep the dummy bytes in the control register if
the command mode is not kept also. This could lead to an inconsistent
setting : normal read mode (command 0x3) and dummy bytes. It is to be
noted that the HW allows such a configuration.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@wedev4u.fr>
These devices are used on OpenPOWER systems. The SPI_NOR_DUAL_READ
flags is added for the Aspeed SoCs which do not support QUAD reads.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@wedev4u.fr>
These modules are used on the OpenPOWER Witherspoon systems to hold
the POWER9 host firmware image. The SPI_NOR_DUAL_READ flags is added
for the Aspeed SoCs which do not support QUAD reads.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@wedev4u.fr>
of_device_ids are not supposed to change at runtime. All functions
working with of_device_ids provided by <linux/of.h> work with const
of_device_ids. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@wedev4u.fr>
Similar to the other ones, different size. The "JV" suffix is in
the datasheet, I haven't seen mentions of a different one.
The datasheet indicates DUAL and QUAD are supported.
http://www.winbond.com/resource-files/w25m512jv%20revc%2001062017.pdf
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@wedev4u.fr>
Before commit cff959958832 ("mtd: spi-nor: introduce SPI 1-2-2 and SPI
1-4-4 protocols") then we treated 1 as -EINVAL in the caller but after
that commit we changed to propagate the return. My static checker
complains that it's eventually passed to an ERR_PTR() and later
dereferenced, but I'm not totally certain if that's true. Regardless,
returning 1 is wrong.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@wedev4u.fr>
This patch fixes some compiler errors:
- change format strings to use %zx for size_t
- add missing #include <linux/sizes.h>
Cc: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@wedev4u.fr>
This patch starts adding support to Octo SPI protocols (SPI x-y-8).
Op codes for Fast Read and/or Page Program operations using Octo SPI
protocols are not known yet (no JEDEC specification has defined them yet)
but we'd rather introduce the Octo SPI protocols now so it's done as it
should be.
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
This patch introduces support to Double Transfer Rate (DTR) SPI protocols.
DTR is used only for Fast Read operations.
According to manufacturer datasheets, whatever the number of I/O lines
used during instruction (x) and address/mode/dummy (y) clock cycles, DTR
is used only during data (z) clock cycles of SPI x-y-z protocols.
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
This patch changes the prototype of spi_nor_scan(): its 3rd parameter
is replaced by a 'struct spi_nor_hwcaps' pointer, which tells the spi-nor
framework about the actual hardware capabilities supported by the SPI
controller and its driver.
Besides, this patch also introduces a new 'struct spi_nor_flash_parameter'
telling the spi-nor framework about the hardware capabilities supported by
the SPI flash memory and the associated settings required to use those
hardware caps.
Then, to improve the readability of spi_nor_scan(), the discovery of the
memory settings and the memory initialization are now split into two
dedicated functions.
1 - spi_nor_init_params()
The spi_nor_init_params() function is responsible for initializing the
'struct spi_nor_flash_parameter'. Currently this structure is filled with
legacy values but further patches will allow to override some parameter
values dynamically, for instance by reading the JESD216 Serial Flash
Discoverable Parameter (SFDP) tables from the SPI memory.
The spi_nor_init_params() function only deals with the hardware
capabilities of the SPI flash memory: especially it doesn't care about
the hardware capabilities supported by the SPI controller.
2 - spi_nor_setup()
The second function is called once the 'struct spi_nor_flash_parameter'
has been initialized by spi_nor_init_params().
With both 'struct spi_nor_flash_parameter' and 'struct spi_nor_hwcaps',
the new argument of spi_nor_scan(), spi_nor_setup() computes the best
match between hardware caps supported by both the (Q)SPI memory and
controller hence selecting the relevant settings for (Fast) Read and Page
Program operations.
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
NAND, from Boris:
"""
- some minor fixes/improvements on existing drivers (fsmc, gpio, ifc,
davinci, brcmnand, omap)
- a huge cleanup/rework of the denali driver accompanied with core
fixes/improvements to simplify the driver code
- a complete rewrite of the atmel driver to support new DT bindings
make future evolution easier
- the addition of per-vendor detection/initialization steps to avoid
extending the nand_ids table with more extended-id entries
"""
SPI NOR, from Cyrille:
"""
- fixes in the hisi SPI controller driver.
- fixes in the intel SPI controller driver.
- fixes in the Mediatek SPI controller driver.
- fixes to some SPI flash memories not supported the Chip Erase command.
- add support to some new memory parts (Winbond, Macronix, Micron, ESMT).
- add new driver for the STM32 QSPI controller.
"""
And a few fixes for Gemini and Versatile platforms on physmap-of
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=dxj5
-----END PGP SIGNATURE-----
Merge tag 'for-linus-20170510' of git://git.infradead.org/linux-mtd
Pull MTD updates from Brian Norris:
"NAND, from Boris:
- some minor fixes/improvements on existing drivers (fsmc, gpio, ifc,
davinci, brcmnand, omap)
- a huge cleanup/rework of the denali driver accompanied with core
fixes/improvements to simplify the driver code
- a complete rewrite of the atmel driver to support new DT bindings
make future evolution easier
- the addition of per-vendor detection/initialization steps to avoid
extending the nand_ids table with more extended-id entries
SPI NOR, from Cyrille:
- fixes in the hisi, intel and Mediatek SPI controller drivers
- fixes to some SPI flash memories not supporting the Chip Erase
command.
- add support to some new memory parts (Winbond, Macronix, Micron,
ESMT).
- add new driver for the STM32 QSPI controller
And a few fixes for Gemini and Versatile platforms on physmap-of"
* tag 'for-linus-20170510' of git://git.infradead.org/linux-mtd: (100 commits)
MAINTAINERS: Update NAND subsystem git repositories
mtd: nand: gpio: update binding
mtd: nand: add ooblayout for old hamming layout
mtd: oxnas_nand: Allocating more than necessary in probe()
dt-bindings: mtd: Document the STM32 QSPI bindings
mtd: mtk-nor: set controller's address width according to nor flash
mtd: spi-nor: add driver for STM32 quad spi flash controller
mtd: nand: brcmnand: Check flash #WP pin status before nand erase/program
mtd: nand: davinci: add comment on NAND subpage write status on keystone
mtd: nand: omap2: Fix partition creation via cmdline mtdparts
mtd: nand: NULL terminate a of_device_id table
mtd: nand: Fix a couple error codes
mtd: nand: allow drivers to request minimum alignment for passed buffer
mtd: nand: allocate aligned buffers if NAND_OWN_BUFFERS is unset
mtd: nand: denali: allow to override revision number
mtd: nand: denali_dt: use pdev instead of ofdev for platform_device
mtd: nand: denali_dt: remove dma-mask DT property
mtd: nand: denali: support 64bit capable DMA engine
mtd: nand: denali_dt: enable HW_ECC_FIXUP for Altera SOCFPGA variant
mtd: nand: denali: support HW_ECC_FIXUP capability
...
When nor's size larger than 16MByte, nor's address width maybe
set to 3 or 4, and controller should change address width according
to nor's setting.
Signed-off-by: Guochun Mao <guochun.mao@mediatek.com>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
The quadspi is a specialized communication interface targeting single,
dual or quad SPI Flash memories.
It can operate in any of the following modes:
-indirect mode: all the operations are performed using the quadspi
registers
-read memory-mapped mode: the external Flash memory is mapped to the
microcontroller address space and is seen by the system as if it was
an internal memory
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
All required stateless 4-byte op codes are supported by this flash
chip. The stateless 4-byte support can't be autodetected due to a
missing 4-byte Address Instruction Table in SFDP.
Fixes hangs on reboot for SoCs expecting the flash chip in 3byte mode.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Add new Micron N25Q256A (N25Q256A11) 256Mbit NOR Flash in the list
of supported devices. This chip has the same structure as the N25Q256A
but ID and voltage (1V8) to use is different. Therefore, this adds
N25Q256A11 as n25q256ax1.
In the future, for new Micron memories we could use the patterns
"n25q*ax1" for 1V8 and "n25q*ax3" for 3V3 memories.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.kw@hitachi.com>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Macronix MX25U2033E, MX25U4033E and MX25U4035 devices are used in 4/5/6th
generation Kindle ebook readers. Both MX25U403x variants share the same
JEDEC id. Add those spi-nor variants and the similar MX25U8035 mentioned
in the same set of datasheets.
Signed-off-by: Alexander Kurz <akurz@blala.de>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Winbond W25Q20BW devices are used in 4/5th generation Kindle ebook readers.
Add this spi-nor device and the similar W25Q20 devices to the list of known
devices.
Signed-off-by: Alexander Kurz <akurz@blala.de>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Micron n25q00 are stacked chips, thus do not support chip erase.
>From now spi-nor framework will not send chip erase command,
instead will use sector at time erase procedure.
Signed-off-by: Marcin Krzeminski <mar.krzeminski@gmail.com>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Currently it is possible to disable chip erase for spi-nor driver.
Some modern stacked (multi die) flash chips do not support chip
erase opcode at all but spi-nor framework needs to cope with them too.
This commit extends existing functionality to allow disable
chip erase for a single flash chip.
Signed-off-by: Marcin Krzeminski <mar.krzeminski@gmail.com>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Fix typos and add the following to the scripts/spelling.txt:
disble||disable
disbled||disabled
I kept the TSL2563_INT_DISBLED in /drivers/iio/light/tsl2563.c
untouched. The macro is not referenced at all, but this commit is
touching only comment blocks just in case.
Link: http://lkml.kernel.org/r/1481573103-11329-20-git-send-email-yamada.masahiro@socionext.com
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add support for the ESMT F25L32QA and F25L64QA.
These are 4MB and 8MB SPI-NOR Chips from Elite Semiconductor Memory
Technology.
Signed-off-by: L. D. Pinney <ldpinney@gmail.com>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
This fixes a sparse warning about incorrect type in return expression.
Signed-off-by: Nicholas Mc Guire <der.herr@hofr.at>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
writeable in struct intel_spi is a boolean and assignment should be to
true/false not 1/0 as recommended by boolinit.cocci.
Signed-off-by: Nicholas Mc Guire <der.herr@hofr.at>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
There is a error message within devm_ioremap_resource
already, so remove the dev_err call to avoid redundant
error message.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
- add support to the 4-byte address instruction set.
- add support to new memory parts.
- add support to S3AN memories.
- add support to the Intel SPI controller.
- add support to the Aspeed AST2400 and AST2550 controllers.
- fix max SPI transfer and message sizes in m25p80_read().
- fix the Candence QSPI driver.
- fix the Freescale QSPI driver.
-----BEGIN PGP SIGNATURE-----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=/fPM
-----END PGP SIGNATURE-----
Merge tag 'spi-nor/for-4.11-v2' of git://github.com/spi-nor/linux
From Cyrille:
"""
This pull request contains the following notable changes:
- add support to the 4-byte address instruction set.
- add support to new memory parts.
- add support to S3AN memories.
- add support to the Intel SPI controller.
- add support to the Aspeed AST2400 and AST2550 controllers.
- fix max SPI transfer and message sizes in m25p80_read().
- fix the Candence QSPI driver.
- fix the Freescale QSPI driver.
"""
Checking for ret < 0 is redundant because a previous check on ret
being non-zero already handles the ret < 0 case. Remove the redundant
code. Found by CoverityScan, CID#1398863, CID#1398864
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Richard Weinberger <richard@nod.at>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
There are some read modes for flash, such as NORMAL, FAST,
QUAD, DDR QUAD. These modes will use the identical lut table base
So rename SEQID_QUAD_READ to SEQID_READ.
Signed-off-by: Yunhui Cui <B56489@freescale.com>
Signed-off-by: Yunhui Cui <yunhui.cui@nxp.com>
Acked-by: Han xu <han.xu@nxp.com>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
We can get the read/write/erase opcode from the spi nor framework
directly. This patch uses the information stored in the SPI-NOR to
remove the hardcode in the fsl_qspi_init_lut().
Signed-off-by: Yunhui Cui <B56489@freescale.com>
Signed-off-by: Yunhui Cui <yunhui.cui@nxp.com>
Acked-by: Han xu <han.xu@nxp.com>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
The page calculation under spi_nor_s3an_addr_convert() was wrong. On
Default Address Mode we need to perform a divide by page_size.
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
The first argument of ioread32_rep() and ioread8_rep is not
const. Change aspeed_smc_read_from_ahb() prototype to fix compile
warning :
drivers/mtd/spi-nor/aspeed-smc.c: In function 'aspeed_smc_read_from_ahb':
drivers/mtd/spi-nor/aspeed-smc.c:212:16: warning: passing argument 1 of 'ioread32_rep' discards 'const' qualifier from pointer target type [-Wdiscarded-qualifiers]
ioread32_rep(src, buf, len >> 2);
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
-----BEGIN PGP SIGNATURE-----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=1Yep
-----END PGP SIGNATURE-----
Merge tag 'ib-mfd-mtd-v4.11' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
From Lee Jones:
"""
Immutable branch between MFD and MTD due for the v4.11 merge window
"""
This chip has write protection enabled on power-up,
so this flag is necessary to support write operations.
Signed-off-by: Victor Shyba <victor1984@riseup.net>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
This patch provides an alternative mean to support memory above 16MiB
(128Mib) by replacing 3byte address op codes by their associated 4byte
address versions.
Using the dedicated 4byte address op codes doesn't change the internal
state of the SPI NOR memory as opposed to using other means such as
updating a Base Address Register (BAR) and sending command to enter/leave
the 4byte mode.
Hence when a CPU reset occurs, early bootloaders don't need to be aware
of BAR value or 4byte mode being enabled: they can still access the first
16MiB of the SPI NOR memory using the regular 3byte address op codes.
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Tested-by: Vignesh R <vigneshr@ti.com>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
This patch renames the SPINOR_OP_* macros of the 4-byte address
instruction set so the new names all share a common pattern: the 4-byte
address name is built from the 3-byte address name appending the "_4B"
suffix.
The patch also introduces new op codes to support other SPI protocols such
as SPI 1-4-4 and SPI 1-2-2.
This is a transitional patch and will help a later patch of spi-nor.c
to automate the translation from the 3-byte address op codes into their
4-byte address version.
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
This driver adds mtd support for the Aspeed AST2400 SoC static memory
controllers:
* New Static Memory Controller (referred as FMC)
. BMC firmware
. AST2500 compatible register set
. 5 chip select pins (CE0 ∼ CE4)
. supports NOR flash, NAND flash and SPI flash memory.
* SPI Flash Controller (SPI)
. host Firmware
. slightly different register set, between AST2500 and the legacy
controller
. supports SPI flash memory
. 1 chip select pin (CE0)
The legacy static memory controller (referred as SMC) is not
supported, as well as types other than SPI.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
This driver adds mtd support for the Aspeed AST2500 SoC static memory
controllers :
* Firmware SPI Memory Controller (FMC)
. BMC firmware
. 3 chip select pins (CE0 ~ CE2)
. supports SPI type flash memory (CE0-CE1)
. CE2 can be of NOR type flash but this is not supported by the
driver
* SPI Flash Controller (SPI1 and SPI2)
. host firmware
. 2 chip select pins (CE0 ~ CE1)
. supports SPI type flash memory
Each controller has a memory range on which it maps its flash module
slaves. Each slave is assigned a memory window for its mapping that
can be changed at bootime with the Segment Address Register.
Each SPI flash slave can then be accessed in two modes: Command and
User. When in User mode, accesses to the memory segment of the slaves
are translated in SPI transfers. When in Command mode, the HW
generates the SPI commands automatically and the memory segment is
accessed as if doing a MMIO.
Currently, only the User mode is supported. Command mode needs a
little more work to check that the memory window on the AHB bus fits
the module size.
Based on previous work from Milton D. Miller II <miltonm@us.ibm.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
This patch removes the WARN_ONCE() test in spi_nor_write().
This macro triggers the display of a warning message almost every time we
use a UBI file-system because a write operation is performed at offset 64,
which is in the middle of the SPI NOR memory page. This is a valid
operation for ubifs.
Hence this warning is pretty annoying and useless so we just remove it.
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Suggested-by: Richard Weinberger <richard@nod.at>
Suggested-by: Andras Szemzo <szemzo.andras@gmail.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The patch checks whether the Quad Enable bit is already set in the Status
Register. If so, the function exits immediately with a successful return
code.
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
Xilinx Spartan-3AN FPGAs contain an In-System Flash where they keep
their configuration data and (optionally) some user data.
The protocol of this flash follows most of the spi-nor standard. With
the following differences:
- Page size might not be a power of two.
- The address calculation (default addressing mode).
- The spi nor commands used.
Protocol is described on Xilinx User Guide UG333
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Cc: Boris Brezillon <boris.brezillon@free-electrons.com>
Cc: Brian Norris <computersforpeace@gmail.com>
Cc: Marek Vasut <marek.vasut@gmail.com>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
The x86-64 and some other architectures are missing readsl/writesl
functions, so this driver won't build on them. Use a more portable
ioread32_rep()/iowrite32_rep() instead.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alan Tull <atull@opensource.altera.com>
Cc: Brian Norris <computersforpeace@gmail.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Graham Moore <grmoore@opensource.altera.com>
Cc: Vignesh R <vigneshr@ti.com>
Cc: Yves Vandervennet <yvanderv@opensource.altera.com>
Suggested-by: Stefan Roese <sr@denx.de>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Add support for the SPI serial flash host controller found on many Intel
CPUs including Baytrail and Braswell. The SPI serial flash controller is
used to access BIOS and other platform specific information. By default the
driver exposes a single read-only MTD device but with a module parameter
"writeable=1" the MTD device can be made read-write which makes it possible
to upgrade BIOS directly from Linux.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
All fsl_qspi_devtype_data structures are never modified.
This patch constify them.
Signed-off-by: LABBE Corentin <clabbe.montjoie@gmail.com>
Acked-by: Han Xu <han.xu@nxp.com>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Add Everspin mr25h40 512KB MRAM to the list of supported chips.
Signed-off-by: Masahiko Iwamoto <iwamoto@allied-telesis.co.jp>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Acked-by: Marek Vasut <marex@denx.de>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
This commit adds support in the spi-nor driver for the
N25Q016A, a 16Mbit SPI NOR flash from Micron.
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Brian Norris <computersforpeace@gmail.com>
Cc: Jagan Teki <jteki@openedev.com>
Signed-off-by: Moritz Fischer <moritz.fischer@ettus.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Add Atmel at25df321 spi-nor flash to the list of spi_nor_ids.
Cc: Brian Norris <computersforpeace@gmail.com>
Cc: Wenyou Yang <wenyou.yang@atmel.com>
Signed-off-by: Jagan Teki <jteki@openedev.com>
Acked-by: Wenyou Yang <wenyou.yang@atmel.com>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
We return success or possibly uninitialized values on these error paths
instead of proper error codes.
Fixes: 1406234105 ("mtd: spi-nor: Add driver for Cadence Quad SPI Flash Controller")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Moritz Fischer <moritz.fischer@ettus.com>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
There are CQSPI_MAX_CHIPSELECT elements in the ->f_pdata array so the >
should be >=.
Fixes: 1406234105 ('mtd: spi-nor: Add driver for Cadence Quad SPI Flash Controller')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
The Spansion S25FL128S also supports dual read mode.
In addition remove flag SECT_4K. 4K erases are supported,
but not uniformly.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
With the S25FL127S nor flash part, each writing to the configuration
register takes hundreds of ms. During that time, no more accesses to
the flash should be done (even reads).
This commit adds a wait loop after the register writing until the flash
finishes its work.
This issue could make rootfs mounting fail when the latter was done too
much closely to this quad enable bit setting step. And in this case, a
driver as UBIFS may try to recover the filesystem and may broke it
completely.
Signed-off-by: Joël Esponde <joel.esponde@honeywell.com>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
This controller driver is used only on ARM but is mostly written
portably so it can build on other arch'es. Unfortunately, at least x86
doesn't provibe readsl()/writesl() accessors. We could possibly fix this
issue in the future by using io{read,write}32_rep() instead, but let's
just drop the architectures we aren't using for now.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Add support for the Cadence QSPI controller. This controller is
present in the Altera SoCFPGA SoCs and this driver has been tested
on the Cyclone V SoC.
Signed-off-by: Graham Moore <grmoore@opensource.altera.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alan Tull <atull@opensource.altera.com>
Cc: Brian Norris <computersforpeace@gmail.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Graham Moore <grmoore@opensource.altera.com>
Cc: Vignesh R <vigneshr@ti.com>
Cc: Yves Vandervennet <yvanderv@opensource.altera.com>
Cc: devicetree@vger.kernel.org
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
This driver add support to the new Atmel QSPI controller embedded into
sama5d2x SoCs. It expects a NOR memory to be connected to the QSPI
controller.
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Gigadevice flash support BP{0,1,2,3,4} bits, where BP3 means the same as
the existing supported TB (Top/Bottom), and BP4 means the same as the
not-yet-supported 4K bit used on other flash (e.g., Winbond). Let's
support lock/unlock with the same feature flags as w25q32dw/w25q64dw.
Tested on gd25lq64c, but I checked datasheets for the other 3, to make
sure.
While I was at it, I noticed that these all support dual and quad as
well. I noted them, but can't test them at the moment, since my test
system only supports standard 1x SPI.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Add Micron (n25q00a) 1Gbit NOR Flash in the list of supported
devices.
This part is different from n25q00 in Memory Type.
Memory Type for n25q00 - BAh
Memory Type for n25q00a - BBh
Signed-off-by: P L Sai Krishna <lakshmis@xilinx.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
In stm_unlock(), the test to determine whether we've fully unlocked the
flash checks for the lock length to be equal to the flash size. That is
a typo/think-o -- the condition actually means the flash is completely
*locked.* We should be using the inverse condition -- that the lock
length is 0 (i.e., no protection).
The result of this bug is that we never actually turn off the Status
Register Write Disable bit, even if the flash is completely unlocked.
Now we can.
Fixes: 47b8edbf0d ("mtd: spi-nor: disallow further writes to SR if WP# is low")
Reported-by: Giorgio <giorgio.nicole@arcor.de>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Cc: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
mtdblock and ubi do not handle the situation when read returns less data
than requested. Loop in spi-nor until buffer is filled or an error is
returned.
Signed-off-by: Michal Suchanek <hramrach@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Tested-by Cyrille Pitchen <cyrille.pitchen@atmel.com>
Acked-by: Michal Suchanek <hramrach@gmail.com>
Tested-by: Michal Suchanek <hramrach@gmail.com>
The spi-nor write loop assumes that what is passed to the hardware
driver write() is what gets written.
When write() writes less than page size at once data is dropped on the
floor. Check the amount of data writen and exit if it does not match
requested amount.
Signed-off-by: Michal Suchanek <hramrach@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Tested-by Cyrille Pitchen <cyrille.pitchen@atmel.com>
Acked-by: Michal Suchanek <hramrach@gmail.com>
Tested-by: Michal Suchanek <hramrach@gmail.com>
Do not pass retlen to hardware driver read/write functions. Update it in
spi-nor generic driver instead.
Signed-off-by: Michal Suchanek <hramrach@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Tested-by Cyrille Pitchen <cyrille.pitchen@atmel.com>
Acked-by: Michal Suchanek <hramrach@gmail.com>
Tested-by: Michal Suchanek <hramrach@gmail.com>
SPI NOR hardware drivers now return useful value from their write
functions so check them.
Signed-off-by: Michal Suchanek <hramrach@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Tested-by Cyrille Pitchen <cyrille.pitchen@atmel.com>
Acked-by: Michal Suchanek <hramrach@gmail.com>
Tested-by: Michal Suchanek <hramrach@gmail.com>
Add checking of SPI transfer errors and return them from read/write
functions. Also return the amount of data transferred.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Add checking of SPI transfer errors and return them from read/write
functions. Also return the amount of data transferred.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Return amount of data read/written or error as read(2)/write(2) does.
Signed-off-by: Michal Suchanek <hramrach@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Change the return value of spi-nor device read and write methods to
allow returning amount of data transferred and errors as
read(2)/write(2) does.
Also, start handling positive returns in spi_nor_read(), since we want
to convert drivers to start returning the read-length both via *retlen
and the return code. (We don't need to do the same transition process
for spi_nor_write(), since ->write() didn't used to have a return code
at all.)
Signed-off-by: Michal Suchanek <hramrach@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Tested-by Cyrille Pitchen <cyrille.pitchen@atmel.com>
Acked-by: Michal Suchanek <hramrach@gmail.com>
Tested-by: Michal Suchanek <hramrach@gmail.com>
Also note the GigaDevice JEDEC ID.
No write-protect support yet, since this flash uses a different status
register layout.
Cc: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Acked-by: Marek Vasut <marex@denx.de>
These are recent Winbond models that are known to have lock/unlock
support via writing the Status Register, and that also support the TB
(Top/Bottom) protection bit.
Tested on w25q32dw.
[Note on style: these entries are getting pretty long lines, so I picked
a style that seems reasonable for splitting up the flags separate from
the other mostly-similar fields.]
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Reviewed-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Tested-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Some flash support a bit in the status register that inverts protection
so that it applies to the bottom of the flash, not the top. This yields
additions to the protection range table, as noted in the comments.
Because this feature is not universal to all flash that support
lock/unlock, control it via a new flag.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Tested-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
We can't determine this purely by manufacturer type (see commit
67b9bcd369 ("mtd: spi-nor: fix Spansion regressions (aliased with
Winbond)")), and it's not autodetectable by anything like SFDP. So make
a new flag for it.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Reviewed-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Tested-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
It's a little easier to read and make sure there are no collisions
(IMO).
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Reviewed-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Tested-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Locking the flash is most useful if it provides real hardware security.
Otherwise, it's little more than a software permission bit.
A reasonable use case that provides real HW security might be like
follows:
(1) hardware WP# is deasserted
(2) program flash
(3) flash range is protected via status register
(4) hardware WP# is asserted
(5) flash protection range can no longer be changed, until WP# is
deasserted
In this way, flash protection is co-owned by hardware and software.
Now, one would expect to be able to perform step (3) with
ioctl(MEMLOCK), except that the spi-nor driver does not set the Status
Register Protect bit (a.k.a. Status Register Write Disable (SRWD)), so
even though the range is now locked, it does not satisfy step (5) -- it
can still be changed by a call to ioctl(MEMUNLOCK).
So, let's enable status register protection after the first lock
command, and disable protection only when the flash is fully unlocked.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Tested-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
There are a few different corner cases to the current logic that seem
undesirable:
* mtd_lock() with offs==0 trips a bounds issue on
ofs - mtd->erasesize < 0
* mtd_unlock() on the middle of a flash that is already unlocked will
return -EINVAL
* probably other corner cases
So, let's stop doing "smart" checks like "check the block below us",
let's just do the following:
(a) pass only non-negative offsets/lengths to stm_is_locked_sr()
(b) add a similar stm_is_unlocked_sr() function, so we can check if the
*entire* range is unlocked (and not just whether some part of it is
unlocked)
Then armed with (b), we can make lock() and unlock() much more
symmetric:
(c) short-circuit the procedure if there is no work to be done, and
(d) check the entire range above/below
This also aligns well with the structure needed for proper TB
(Top/Bottom) support.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Tested-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
If, for instance, the entire flash is already unlocked and I try to
mtd_unlock() the entire device, I don't expect to see an EINVAL error.
It should just silently succeed. Ditto for mtd_lock().
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Reviewed-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Tested-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Fixup a piece leftover by commit 32321e950d ("mtd: spi-nor: wait until
lock/unlock operations are ready"). That commit made us wait for the WIP
bit to settle after lock/unlock operations, but it missed the open-coded
"unlock" that happens at probe() time.
We should probably have this code utilize the unlock() routines in the
future, to avoid duplication, but unfortunately, flash which need to be
unlocked don't all have a proper ->flash_unlock() callback.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Cc: Stas Sergeev <stsp@users.sourceforge.net>
Reviewed-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Tested-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
LS1043a and LS2080A in the Layerscape family also support Freescale Quad
SPI, make Quad SPI selectable for these hardwares.
Signed-off-by: Yuan Yao <yao.yuan@nxp.com>
Acked-by: Han xu <han.xu@nxp.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
LS1021a also support Freescale Quad SPI controller.
Add fsl-quadspi support for ls1021a chip and make SPI_FSL_QUADSPI
selectable for LS1021A SOC hardwares.
Signed-off-by: Yuan Yao <yao.yuan@nxp.com>
Acked-by: Han xu <han.xu@freescale.com>
Acked-by: Han xu <han.xu@nxp.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Add R/W functions for big- or little-endian registers:
The qSPI controller's endian is independent of the CPU core's endian.
So far, the qSPI have two versions for big-endian and little-endian.
Signed-off-by: Yuan Yao <yao.yuan@nxp.com>
Acked-by: Han xu <han.xu@freescale.com>
Acked-by: Han xu <han.xu@nxp.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Micron n25q128axx support subsector (4K) erase so let's update the flags.
Tested on n25q128a13.
Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
This patch remove the micron_quad_enable() function which force the Quad
SPI mode. However, once this mode is enabled, the Micron memory expect ALL
commands to use the SPI 4-4-4 protocol. Hence a failure does occur when
calling spi_nor_wait_till_ready() right after the update of the Enhanced
Volatile Configuration Register (EVCR) in the micron_quad_enable() as
the SPI controller driver is not aware about the protocol change.
Since there is almost no performance increase using Fast Read 4-4-4
commands instead of Fast Read 1-1-4 commands, we rather keep on using the
Extended SPI mode than enabling the Quad SPI mode.
Let's take the example of the pretty standard use of 8 dummy cycles during
Fast Read operations on 64KB erase sectors:
Fast Read 1-1-4 requires 8 cycles for the command, then 24 cycles for the
3byte address followed by 8 dummy clock cycles and finally 65536*2 cycles
for the read data; so 131112 clock cycles.
On the other hand the Fast Read 4-4-4 would require 2 cycles for the
command, then 6 cycles for the 3byte address followed by 8 dummy clock
cycles and finally 65536*2 cycles for the read data. So 131088 clock
cycles. The theorical bandwidth increase is 0.0%.
Now using Fast Read operations on 512byte pages:
Fast Read 1-1-4 needs 8+24+8+(512*2) = 1064 clock cycles whereas Fast
Read 4-4-4 would requires 2+6+8+(512*2) = 1040 clock cycles. Hence the
theorical bandwidth increase is 2.3%.
Consecutive reads for non sequential pages is not a relevant use case so
The Quad SPI mode is not worth it.
mtd_speedtest seems to confirm these figures.
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Fixes: 548cd3ab54 ("mtd: spi-nor: Add quad I/O support for Micron SPI NOR")
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The Spansion s25fl116k is a 16MBit NOR Flash supporting dual and
quad read operations.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Not every arch has io memory.
So, unbreak the build by fixing the dependencies.
Signed-off-by: Richard Weinberger <richard@nod.at>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
WARNING: drivers/mtd/spi-nor/mtk-quadspi.o(.text+0x77e): Section mismatch in reference from the function mtk_nor_drv_probe() to the function .init.text:mtk_nor_init()
The function mtk_nor_drv_probe() references
the function __init mtk_nor_init().
This is often because mtk_nor_drv_probe lacks a __init
annotation or the annotation of mtk_nor_init is wrong.
Drop the bogus __init from mtk_nor_init() to kill this warning.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
On Micron and Numonyx devices, the status register write command
(WRSR), raises a work-in-progress bit (WIP) on the status register.
The datasheets for these devices specify that while the status
register write is in progress, the status register WIP bit can still
be read to check the end of the operation.
This commit adds a wait_till_ready call on lock/unlock operations,
which is required for Micron and Numonyx but should be harmless for
others. This is needed to prevent applications from issuing erase or
program operations before the unlock operation is completed.
Reported-by: Stas Sergeev <stsp@list.ru>
Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
stm_is_locked_sr() takes the status register (SR) value as the last
parameter, not the second.
Reported-by: Bayi Cheng <bayi.cheng@mediatek.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Cc: Bayi Cheng <bayi.cheng@mediatek.com>
Spansion and Winbond have occasionally used the same manufacturer ID,
and they don't support the same features. Particularly, writing SR=0
seems to break read access for Spansion's s25fl064k. Unfortunately, we
don't currently have a way to differentiate these Spansion and Winbond
parts, so rather than regressing support for these Spansion flash, let's
drop the new Winbond lock/unlock support for now. We can try to address
Winbond support during the next release cycle.
Original discussion:
http://patchwork.ozlabs.org/patch/549173/http://patchwork.ozlabs.org/patch/553683/
Fixes: 357ca38d47 ("mtd: spi-nor: support lock/unlock/is_locked for Winbond")
Fixes: c6fc2171b2 ("mtd: spi-nor: disable protection for Winbond flash at startup")
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Reported-by: Felix Fietkau <nbd@openwrt.org>
Cc: Felix Fietkau <nbd@openwrt.org>
Move write data register before excute command to avoid
missing first byte write to nor flash
Signed-off-by: Bayi Cheng <bayi.cheng@mediatek.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
We should better check the return value from read_sr() and
propagate it in the case of error.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The documenting comment of mtd_erase in mtdcore.c states:
Device drivers are supposed to call instr->callback() whenever
the operation completes, even if it completes with a failure.
Currently the callback isn't called in case of failure. Fix this.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
As of commit 807f16d4db ("mtd: core: set some defaults when
dev.parent is set"), the MTD core will set this for us.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Cc: Bayi Cheng <bayi.cheng@mediatek.com>
according datasheet both chips can erase 4kByte sectors individually
Signed-off-by: Andreas Fenkart <andreas.fenkart@dev.digitalstrom.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Some spi-nor drivers perform sector erase by duplicating their
write_reg() command. Let's not require that the driver fill this out,
and provide a default instead.
Tested on m25p80.c and Medatek's MT8173 SPI NOR flash driver.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
It is theoretically possible to probe this driver without a matching
device tree, so let's guard against this.
Also, use the of_device_get_match_data() helper to make this a bit
simpler.
Coverity complained about this one.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Acked-by: Han xu <han.xu@freescale.com>
We can just alias to the MTD of_node.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Reviewed-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Now that the SPI-NOR/MTD framework pass the 'flash_node' through to the
partition parsing code, we don't have to do it ourselves.
Also convert to mtd_device_register(), since we don't need the 2nd and
3rd parameters anymore.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Reviewed-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Used semantic patch with 'make coccicheck MODE=patch COCCI=script.cocci':
---8<----
virtual patch
@@
struct spi_nor b;
struct spi_nor *c;
expression d;
@@
(
-(b).flash_node = (d)
+spi_nor_set_flash_node(&b, d)
|
-(c)->flash_node = (d)
+spi_nor_set_flash_node(c, d)
)
---8<----
And a manual conversion for the one use of spi_nor_get_flash_node().
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Reviewed-by: Boris Brezillon <boris.brezillon@free-electrons.com>
We should pass along our flash DT node to the MTD layer, so it can set
up ofpart for us.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Reviewed-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Change the READ/WRITE to FSL_READ/FSL_WRITE to resolve any possible
namespace collisions with READ/WRITE macros (e.g., from <linux/fs.h>).
Problems have been seen, for example, on mips:
>> drivers/mtd/spi-nor/fsl-quadspi.c:186:5: error: 'LUT_0' undeclared (first use in this function)
((LUT_##ins) << INSTR0_SHIFT))
^
>> drivers/mtd/spi-nor/fsl-quadspi.c:188:30: note: in expansion of macro 'LUT0'
On SPARC:
drivers/mtd/spi-nor/fsl-quadspi.c: In function 'fsl_qspi_init_lut':
drivers/mtd/spi-nor/fsl-quadspi.c:369:1: error: 'LUT_0' undeclared (first use in this function)
drivers/mtd/spi-nor/fsl-quadspi.c:418:1: error: pasting "LUT_" and "(" does not give a valid preprocessing token
drivers/mtd/spi-nor/fsl-quadspi.c:418:2: error: implicit declaration of function 'LUT_'
And surely on others.
Fixes: d26a22d067 ("mtd: fsl-quadspi: allow building for other ARCHes with COMPILE_TEST")
Reported-by: Guenter Roeck <linux@roeck-us.net>
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Han Xu <b45815@freescale.com>
[Brian: rewrote commit description]
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Building for x86 results in the following build errors:
drivers/mtd/spi-nor/fsl-quadspi.c: In function 'fsl_qspi_init_lut':
>> drivers/mtd/spi-nor/fsl-quadspi.c:355:21: error: 'SZ_16M' undeclared (first use in this function)
if (q->nor_size <= SZ_16M) {
^
drivers/mtd/spi-nor/fsl-quadspi.c:355:21: note: each undeclared identifier is reported only once for each function it appears in
drivers/mtd/spi-nor/fsl-quadspi.c: In function 'fsl_qspi_read':
>> drivers/mtd/spi-nor/fsl-quadspi.c:208:27: error: 'SZ_4M' undeclared (first use in this function)
#define QUADSPI_MIN_IOMAP SZ_4M
^
>> drivers/mtd/spi-nor/fsl-quadspi.c:845:25: note: in expansion of macro 'QUADSPI_MIN_IOMAP'
q->memmap_len = len > QUADSPI_MIN_IOMAP ? len : QUADSPI_MIN_IOMAP;
Explicitly include <linux/sizes.h> to fix the problem.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
This driver doesn't actually need ARCH_MXC to compile. Relax the
constraints.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Acked-by: Han xu <han.xu@freescale.com>
Seen when compile-testing on non-32-bit arch:
CC drivers/mtd/spi-nor/fsl-quadspi.o
drivers/mtd/spi-nor/fsl-quadspi.c: In function 'fsl_qspi_read':
drivers/mtd/spi-nor/fsl-quadspi.c:873:2: warning: format '%d' expects argument of type 'int', but argument 6 has type 'size_t' [-Wformat=]
dev_dbg(q->dev, "cmd [%x],read from 0x%p, len:%d\n",
^
Also drop the '0x' prefixing to the '%p' formatter, since %p already
knows how to format pointers appropriately.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Acked-by: Han xu <han.xu@freescale.com>
Many other flash share the same features as ST Micro. I've tested some
Winbond flash, so add them.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
This enables ioctl(MEMISLOCKED). Status can now be reported in the
mtdinfo or flash_lock utilities found in mtd-utils.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
This code was a bit sloppy, would produce a lot of copy-and-paste, and
did not always provide a sensible interface:
* It didn't validate the length for LOCK and the offset for UNLOCK, so
we were essentially discarding half of the user-supplied data and
assuming what they wanted to lock/unlock
* It didn't do very good error checking
* It didn't make use of the fact that this operation works on
power-of-two dimensions
So, rewrite this to do proper bit arithmetic rather than a bunch of
hard-coded condition tables. Now we have:
* More comments on how this was derived
* Notes on what is (and isn't) supported
* A more exendible function, so we could add support for other
protection ranges
* More accurate locking - e.g., suppose the top quadrant is locked (75%
to 100%); then in the following cases, case (a) will succeed but (b)
will not (return -EINVAL):
(a) user requests lock 3rd quadrant (50% to 75%)
(b) user requests lock 3rd quadrant, minus a few blocks (e.g., 50%
to 73%)
Case (b) *should* fail, since we'd have to lock blocks that weren't
requested. But the old implementation didn't know the difference and
would lock the entire second half (50% to 100%)
This refactoring work will also help enable the addition of
mtd_is_locked() support and potentially the support of bottom boot
protection (TB=1).
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The N25Q032A is identical to the N25Q032 except it has a different
supply voltage range. Therefore, it has a new JEDEC ID.
Signed-off-by: Aurelien Chanot <chanot.a@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
This patch fixes timeout issues seen on large NOR flash (e.g., 16MB
w25q128fw) when using ioctl(MEMERASE) with offset=0 and length=16M. The
input parameters matter because spi_nor_erase() uses a different code
path for full-chip erase, where we use the SPINOR_OP_CHIP_ERASE (0xc7)
opcode.
Fix: use a different timeout for full-chip erase than for other
commands.
While most operations can be expected to perform relatively similarly
across a variety of NOR flash types and sizes (and therefore might as
well use a similar timeout to keep things simple), full-chip erase is
unique, because the time it typically takes to complete:
(1) is much larger than most operations and
(2) scales with the size of the flash.
Let's base our timeout on the original comments stuck here -- that a 2MB
flash requires max 40s to erase.
Small survey of a few flash datasheets I have lying around:
Chip Size (MB) Max chip erase (seconds)
---- -------- ------------------------
w25q32fw 4 50
w25q64cv 8 30
w25q64fw 8 100
w25q128fw 16 200
s25fl128s 16 ~256
s25fl256s 32 ~512
From this data, it seems plenty sufficient to say we need to wait for
40 seconds for each 2MB of flash.
After this change, it might make some sense to decrease the timeout for
everything else, as even the most extreme operations (single block
erase?) shouldn't take more than a handful of seconds. But for safety,
let's leave it as-is. It's only an error case, after all, so we don't
exactly need to optimize it.
Signed-off-by: Furquan Shaikh <furquan@google.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
It is a 512KiB flash with 4 KiB erase sectors.
Signed-off-by: Yuan Yao <yao.yuan@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
s25fl016k can be found on Embedded Artists' LPC4357 Developer's Kit
where is used in quad mode by the LPC4357 SPIFI controller.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The 'write_enable' argument is unused and unneeded, so remove it from
the API.
Signed-off-by: Jagan Teki <jteki@openedev.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Han Xu <han.xu@freescale.com>
[Brian: fixed for nxp-spifi.c]
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Use existing write_sr() call instead of decoding and
calling nor->write_reg separately.
Signed-off-by: Jagan Teki <jteki@openedev.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The problem this patch is trying to address is such, that SPI NOR flash
devices attached to a dedicated SPI NOR controller cannot read their
properties from the associated struct device_node.
A couple of facts first:
1) Each SPI NOR flash has a struct spi_nor associated with it.
2) Each SPI NOR flash has certain device properties associated
with it, for example the OF property 'm25p,fast-read' is a
good pick. These properties are used by the SPI NOR core to
select which opcodes are sent to such SPI NOR flash. These
properties are coming from spi_nor .dev->of_node .
The problem is, that for SPI NOR controllers, the struct spi_nor .dev
element points to the struct device of the SPI NOR controller, not the
SPI NOR flash. Therefore, the associated dev->of_node also is the
one of the controller and therefore the SPI NOR core code is trying to
parse the SPI NOR controller's properties, not the properties of the
SPI NOR flash.
Note: The m25p80 driver is not affected, because the controller and
the flash are the same device, so the associated device_node
of the controller and the flash are the same.
This patch adjusts the SPI NOR core such that the device_node is not
picked from spi_nor .dev directly, but from a new separate spi_nor
.flash_node element. This let's the SPI NOR controller drivers set up
a different spi_nor .flash_node element for each SPI NOR flash.
This patch also fixes the controller drivers to be compatible with
this modification and correctly set the spi_nor .flash_node element.
This patch is inspired by 5844feeaa4
mtd: nand: add common DT init code
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
We don't really need the flash information from the device tree here.
Let's stick with autodetection here instead.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Acked-by: Han Xu <han.xu@freescale.com>
Tested-by: Han Xu <han.xu@freescale.com>
This reflects the proper layering, so let's do it.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Tested-by: Joachim Eastwood <manabian@gmail.com>
Layering suggests that the SPI NOR layer (not the hardware driver)
should be initializing the MTD layer.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Tested-by: Joachim Eastwood <manabian@gmail.com>
This chip can be found on Hitex LPC4350 Evaluation Board.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
According to the datasheet[1], both S25FL129P0 (256kB sectors) and
S25FL129P1 (64kB sectors) support dual read, quad read, dual i/o read
and quad i/o read.
I have verified dual read to be working for S25FL129P1 on a dual
capable spi controller. Quad as well as S25FL129P0 is untested, lacking
hardware to verify.
[1] http://www.spansion.com/Support/Datasheets/S25FL129P_00.pdf
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
It is a 256KiB flash with 4 KiB erase sectors
and 64KiB overlay blocks.
This is the one available on Hardkernel's Odroid U3 shield.
Signed-off-by: Alexis Ballier <aballier@gentoo.org>
[Brian: seems like this does NOT require the usual SST_WRITE hacks]
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Add Micron (n25q064a) 8MB flash to the list of supported chips.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
[Brian: fixup context]
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Using struct spi_device_id for storing list of flash devices comes from
early SPI NOR framework days. Thanks to the commit 70f3ce0510 ("mtd:
spi-nor: make spi_nor_scan() take a chip type name, not spi_device_id")
we can stop using spi_device_id and just switch to our own struct.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The current "We only connect the NOR to this controller now." text
is not very clear, so explain it better by saying that generic SPI
is not supported by SPI_FSL_QUADSPI and only SPI NOR is.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Add SPI-NOR driver for the SPI Flash Interface (SPIFI)
controller that is found on newer NXP MCU devices.
The controller supports serial SPI Flash devices with 1-, 2-
and 4-bit width in either SPI mode 0 or 3. The controller
can operate in either command or memory mode. In memory mode
the Flash is exposed as normal memory and can be directly
accessed by the CPU.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Reviewed-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Erase function will use cmd 0x20 (SPINOR_OP_BE_4K) if kenrel enable option
CONFIG_MTD_SPI_NOR_USE_4K_SECTORS.
This command is not in fsl-quadspi driver LUT. So driver continue report
fsl-quadspi 21e0000.qspi: Unsupported cmd 0x20.
This patch fix this issue.
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Acked-by: Han Xu <Han.xu@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The uboot may run the QuadSpi controler with command:
#sf probe
So we should reset the module in the probe.
This patch also clear the pending interrupts which arised by the uboot
code.
Signed-off-by: Huang Shijie <shijie8@gmail.com>
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
QSPI1 cannot wake up CCM from WAIT mode on SX ARD board, add pmqos to
let PM NOT enter WAIT mode when accessing QSPI1, refer to TKT245618.
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Signed-off-by: Han Xu <Han.xu@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
We found there is a low probability(5%) QSPI access timeout issue,
usually it happened on kernel boot stage, the first time kernel tried to
access QSPI chip. The READ_ID command was sent but not executed,
consequently the probe function failed.
The root cause is that the divider is not glitchless in i.MX6SX chip.
If qspi clock enabled then change clock frequency by call clk_set_rate,
there will be glitch at low possiblity rate and pass to qspi controller.
The controler will be hang by this glitch.
Based on the new clock flag(CLK_SET_RATE_GATE) and new framework, we
need to change the approach of seting clock rate.
1. Disable clock.
2. call clk_set_rate.
3. Enable clock again.
Signed-off-by: Han Xu <han.xu@freescale.com>
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Add i.mx6ul chip support
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Acked-by: Han xu <han.xu@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Support i.mx7d.
quadspi in i.mx7d increase rxfifo.
require fill at least 16byte to trigger data transfer.
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Signed-off-by: Han Xu <han.xu@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
add several quirk to distinguish different version of qspi module.
Signed-off-by: Han Xu <han.xu@freescale.com>
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
QSPI may failed to map enough memory (256MB) for AHB read in
previous implementation, especially in 3G/1G memory layout kernel.
Dynamically map memory to avoid such issue.
This implementation generally map QUADSPI_MAX_IOMAP (default 4MB) memory
for AHB read, it should be enough for common scenarios, and the side
effect (0.6% performance drop) is minor.
Previous implementation
root@imx6qdlsolo:~# dd if=/dev/mtd0 of=/dev/null bs=1K count=32K
32768+0 records in
32768+0 records out
33554432 bytes (34 MB) copied, 2.16006 s, 15.5 MB/s
root@imx6qdlsolo:~# dd if=/dev/mtd0 of=/dev/null bs=32M count=1
1+0 records in
1+0 records out
33554432 bytes (34 MB) copied, 1.43149 s, 23.4 MB/s
After applied the patch
root@imx6qdlsolo:~# dd if=/dev/mtd0 of=/dev/null bs=1K count=32K
32768+0 records in
32768+0 records out
33554432 bytes (34 MB) copied, 2.1743 s, 15.4 MB/s
root@imx6qdlsolo:~# dd if=/dev/mtd0 of=/dev/null bs=32M count=1
1+0 records in
1+0 records out
33554432 bytes (34 MB) copied, 1.43158 s, 23.4 MB/s
Signed-off-by: Han Xu <han.xu@freescale.com>
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
When we added the "jedec,spi-nor" compatible string for use in this
driver, we added it as a modalias option. The modalias can be derived in
different ways for platform devices vs. device tree (of_*) matching. But
for device tree matching (the primary target of this identifier string),
the modalias is determined from the first entry in the 'compatible'
property. IOW, the following properties would bind to this driver:
// Option (a), modalias = "spi-nor"
compatible = "jedec,spi-nor";
// Option (b), modalias = "spi-nor"
compatible = "idontknowwhatimdoing,spi-nor";
But the following would not:
// Option (c), modalias = "shinynewdevice"
compatible = "myvendor,shinynewdevice", "jedec,spi-nor";
So, we'd like to match (a) and (c) (even when we don't have an explicit
entry for "shinynewdevice"), and we'd rather not allow (b).
To do this, we
(1) always (for devices without specific platform data) pass the
modalias to the spi-nor library;
(2) rework the spi-nor library to not reject "bad" names, and
instead just fall back to autodetection; and
(3) add the .of_match_table to properly catch all "jedec,spi-nor".
This allows (a) and (c) without warnings, and rejects (b).
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
QUADSPI_MCR_CLR_TXF_MASK is the correct mask for clearing the TX FIFO.
Signed-off-by: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Add supports for simultaneous access to multiple chips. Need to lock
the mutex before any quad spi operations and unlock the mutex after
operations complete.
Signed-off-by: Han Xu <b45815@freescale.com>
[Brian: reworked err path in fsl_qspi_prep()]
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Few recently added entries are missing SECT_4K flag despite of these
flashes supporting 4 KiB erase sectors and 0x20 erase command.
Also add a comment to help avoiding such mistakes in the future.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Cc: Knut Wohlrab <knut.wohlrab@de.bosch.com>
Cc: Huang Shijie <shijie.huang@intel.com>
Cc: Shengzhou Liu <shengzhou.liu@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
of_device_id is always used as const.
(See driver.of_match_table and open firmware functions)
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Add Macronix (mx25u6435f) 8MB flash to the list of supported chips.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Add Winbond (w25q64dw) 8MB flash to the list of supported chips.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Add support for EON en25s64 SPI flash.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
return type of wait_for_completion_timeout is unsigned long not int, this
patch uses the return value of wait_for_completion_timeout in the condition
directly rather than adding a additional appropriately typed variable.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Acked-by: Han Xu <han.xu@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
When displaying dev_err() messages it is useful to print the error value.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Han Xu <han.xu@freescale.com>
[Brian: fix up "can not" at the same time]
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Flash lock/unlock is a flash-specific operations. Factor out a callback
for it to more readily support other vendors.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Tested-by: VIET NGA DAO <vndao@altera.com>
Set AHB transfer size to 1K which improved the read performance.
Add ahb_buf_size field in fsl_qspi_devtype_data to denote the size for
different SoC.
Before:
root@imx6qdlsolo:~# dd if=/dev/mtd1 of=/dev/null bs=1M count=16
16+0 records in
16+0 records out
16777216 bytes (17 MB) copied, 0.472183 s, 25.1 MB/s
After:
root@imx6qdlsolo:~# dd if=/dev/mtd1 of=/dev/null bs=1M count=16
16+0 records in
16+0 records out
16777216 bytes (17 MB) copied, 0.369439 s, 29.5 MB/s
Signed-off-by: Allen Xu <b45815@freescale.com>
Signed-off-by: Huang Shijie <shijie8@gmail.com>
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Acked-by: Huang Shijie <shijie.huang@intel.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
There is no need to keep the 'map_failed' label. We can simply return the error
code directly and let the code shorter and cleaner.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Han Xu <han.xu@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
When the driver successfully probe we already have messages like:
[ 1.140989] fsl-quadspi 21e4000.qspi: s25fl128s (16384 Kbytes)
[ 1.150902] fsl-quadspi 21e4000.qspi: s25fl128s (16384 Kbytes)
Or in case of error:
[ 1.175920] fsl-quadspi: probe of 21e4000.qspi failed with error -12
, so remove the unneeded success/error messages.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Han Xu <han.xu@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Jumping to 'map_failed' label is not correct at these points, as it misses to
disable the clocks that were previously enabled.
Jump to 'irq_failed' label instead that will correctly disable the clocks.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Han Xu <han.xu@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
When removing the fsl-quadspi module and running 'cat /proc/mtd' afterwards,
we see garbage data like:
$ rmmod fsl-quadspi
$ cat /proc/mtd
dev: size erasesize name
mtd0: 00000000 00000000 "(null)"
mtd0: 00000000 00000000 "(null)"
mtd0: 00000000 00000000 "(null)"
...
mtd0: a22296c6c756e28 00000000 "(null)"
mtd0: a22296c6c756e28 3064746d "(null)"
If we continue doing multiple module load/unload operations, then it will also
lead to a kernel crash.
The reason for this is due to the wrong mtd index used in
mtd_device_unregister() in the remove function.
We need to keep the mtd unregister index aligned with the one used in the probe
function, which means we need to take into account the 'has_second_chip'
property. By doing so we can guarantee that the mtd index is the same in the
registration and unregistration functions.
With this patch applied we can load/unload the fsl-quadspi driver several times
and it will result in no crash.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Huang Shijie <shijie.huang@intel.com>
Tested-by: Frank Li <Frank.Li@freescale.com>
Acked-by: Allen Xu <han.xu@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
i.mx6 sx support turn off fastmix and megamix power.
qpsi controller can be turned off and all status lost when suspend/resume.
add suspend/resume functions and reset qspi controller when resume.
Signed-off-by: Allen Xu <b45815@freescale.com>
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Acked-by: Huang Shijie <shijie.huang@intel.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
This patch adds code which enables Quad I/O mode on Micron SPI NOR flashes.
For Micron SPI NOR flash, enabling or disabling quad I/O protocol can be
done By two methods, which are to use EVCR (Enhanced Volatile
Configuration Register) and the ENTER QUAD I/O MODE command. There is no
difference between these two methods. Unfortunately, for some Micron SPI
NOR flashes, there no ENTER Quad I/O command (35h), such as n25q064. But
for all current Micron SPI NOR, if it support quad I/O mode, using EVCR
definitely be supported. It is a recommended method to enable Quad I/O
mode by EVCR, Quad I/O protocol bit 7. When EVCR bit 7 is reset to 0,
the SPI NOR flash will operate in quad I/O mode.
This patch has been tested on N25Q512A and MT25TL256BAA1ESF. Micron SPI
NOR of spi_nor_ids[] table all support this method.
Signed-off-by: Bean Huo <beanhuo@micron.com>
Acked-by: Marek Vasut <marex@denx.de>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
* Add device tree support for DoC3
* SPI NOR:
Refactoring, for better layering between spi-nor.c and its driver users
(e.g., m25p80.c)
New flash device support
Support 6-byte ID strings
* NAND
New NAND driver for Allwinner SoC's (sunxi)
GPMI NAND: add support for raw (no ECC) access, for testing purposes
Add ATO manufacturer ID
A few odd driver fixes
* MTD tests:
Allow testers to compensate for OOB bitflips in oobtest
Fix a torturetest regression
* nandsim: Support longer ID byte strings
And more.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=gDW8
-----END PGP SIGNATURE-----
Merge tag 'for-linus-20141215' of git://git.infradead.org/linux-mtd
Pull MTD updates from Brian Norris:
"Summary:
- Add device tree support for DoC3
- SPI NOR:
Refactoring, for better layering between spi-nor.c and its
driver users (e.g., m25p80.c)
New flash device support
Support 6-byte ID strings
- NAND:
New NAND driver for Allwinner SoC's (sunxi)
GPMI NAND: add support for raw (no ECC) access, for testing
purposes
Add ATO manufacturer ID
A few odd driver fixes
- MTD tests:
Allow testers to compensate for OOB bitflips in oobtest
Fix a torturetest regression
- nandsim: Support longer ID byte strings
And more"
* tag 'for-linus-20141215' of git://git.infradead.org/linux-mtd: (63 commits)
mtd: tests: abort torturetest on erase errors
mtd: physmap_of: fix potential NULL dereference
mtd: spi-nor: allow NULL as chip name and try to auto detect it
mtd: nand: gpmi: add raw oob access functions
mtd: nand: gpmi: add proper raw access support
mtd: nand: gpmi: add gpmi_copy_bits function
mtd: spi-nor: factor out write_enable() for erase commands
mtd: spi-nor: add support for s25fl128s
mtd: spi-nor: remove the jedec_id/ext_id
mtd: spi-nor: add id/id_len for flash_info{}
mtd: nand: correct the comment of function nand_block_isreserved()
jffs2: Drop bogus if in comment
mtd: atmel_nand: replace memcpy32_toio/memcpy32_fromio with memcpy
mtd: cafe_nand: drop duplicate .write_page implementation
mtd: m25p80: Add support for serial flash Spansion S25FL132K
MTD: m25p80: fix inconsistency in m25p_ids compared to spi_nor_ids
mtd: spi-nor: improve wait-till-ready timeout loop
mtd: delete unnecessary checks before two function calls
mtd: nand: omap: Fix NAND enumeration on 3430 LDP
mtd: nand: add ATO manufacturer info
...
This will allow spi-nor users to plainly use JEDEC to detect flash chip.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
write_enable() was being duplicated to both m25p80.c and fsl-quadspi.c.
But this should be handled within the spi-nor abstraction layer.
At the same time, let's add write_disable() after erasing, so we don't
leave the flash in a write-enabled state afterward.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Acked-by: Huang Shijie <shijie.huang@intel.com>
We need to store the six bytes ID for s25fl128s, since it shares the same
five bytes with s25fl129p1.
This patch adds a macro INFO6 which is used for the six bytes ID flash, and adds
a new item for the s25fl128s.
Signed-off-by: Huang Shijie <shijie.huang@intel.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The "id" array contains all the information about the JEDEC and the
manufacturer ID info. This patch removes the jedec_id/ext_id from
flash_info.
Signed-off-by: Huang Shijie <shijie.huang@intel.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
This patch adds the id/id_len fields for flash_info{}, and rewrite the
INFO to fill them. And at last, we read out 6 bytes in the spi_nor_read_id(),
and we use these new fields to parse out the correct flash_info.
Signed-off-by: Huang Shijie <shijie.huang@intel.com>
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
There are a few small issues with the timeout loop in
spi_nor_wait_till_ready():
* The first operation should not be a reschedule; we should check the
status register at least once to see if we're complete!
* We should check the status register one last time after declaring the
deadline has passed, to prevent a premature timeout error (this is
theoretically possible if we sleep for a long time after the previous
status register check).
* Add an error message, so it's obvious if we ever hit a timeout.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Acked-by: Huang Shijie <shijie.huang@intel.com>
Reviewed-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Add sst25wf080 to the spi-nor device id table.
Signed-off-by: Harini Katakam <harinik@xilinx.com>
Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Marek Vasut <marex@denx.de>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Tested with this particular FRAM chip
Signed-off-by: Rostislav Lisovy <lisovy@merica.cz>
Acked-by: Marek Vasut <marex@denx.de>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Because n25q032 is the Micron SPI chip, move it to Micron
devices list group. In order that know which Micron SPI
chips have been support at a glance.
Signed-off-by: Chunhe Lan <Chunhe.Lan@freescale.com>
Cc: Brian Norris <computersforpeace@gmail.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Huang Shijie <shijie8@gmail.com>
Acked-by: Marek Vasut <marex@denx.de>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
We don't need to expose a 'wait-till-ready' interface to drivers. Status
register polling should be handled by the core spi-nor.c library, and as
of now, I see no need to provide a special driver-specific hook for it.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Reviewed-by: Marek Vasut <marex@denx.de>
spi-nor.c should be taking care of these now.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Cc: Huang Shijie <b32955@freescale.com>
Reviewed-by: Marek Vasut <marex@denx.de>
We shouldn't have *every* function checking if a previous write is
complete; this should be done synchronously after each write/erase.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Reviewed-by: Marek Vasut <marex@denx.de>
The error label was unused here. It looks like we're missing at least
one case that should be doing 'goto write_err'.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Acked-by: Huang Shijie <shijie8@gmail.com>
These functions were near-carbon-copies due to a small per-flash quirk.
Let's add a new spi_nor::flags bitfield to support these types of
quirks.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Cc: Graham Moore <grmoore@altera.com>
Cc: Huang Shijie <shijie8@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
For the DDR Quad read, the dummy cycles maybe 3 or 6 which is less then 8.
The dummy cycles is actually 8 for SPI fast/dual/quad read.
This patch makes preparations for the DDR quad read, it fixes the wrong dummy
value for both the spi-nor.c and m25p80.c.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Acked-by: Marek Vasut <marex@denx.de>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
When clk_prepare_enable(q->clk) fails it is clearer to disable the previous
acquired clock (q->clk_en) in the error path rather than doing it locally.
So disable q->clk_en in the error path only.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Huang Shijie <shijie8@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The 'map_failed' label will return 'ret', so we need to assign the error
code to 'ret', otherwise the probe function will return success.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Huang Shijie <shijie8@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
There is currently no useful way to override the default
implementation of this operation. The returned struct spi_device_id
must have a pointer to struct flash_info in its private data, but this
structure is defined inside spi-nor.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
m25p80's device ID table is now spi_nor_ids, defined in spi-nor. The
MODULE_DEVICE_TABLE() macro doesn't work with extern definitions, but
its use was also removed at the same time. Now if m25p80 is built as
a module it doesn't get the necessary aliases to be loaded
automatically.
A clean solution to this will involve defining the list of device
IDs in spi-nor.h and removing struct spi_device_id from the spi-nor
API, but this is quite a large change.
As a quick fix suitable for stable, copy the device IDs back into
m25p80.
Fixes: 03e296f613 ("mtd: m25p80: use the SPI nor framework")
Cc: <stable@vger.kernel.org> # 3.16.x: 32f1b7c8352f: mtd: move support for struct flash_platform_data into m25p80
Cc: <stable@vger.kernel.org> # 3.16.x: 90e55b3812a1: mtd: m25p80: get rid of spi_get_device_id
Cc: <stable@vger.kernel.org> # 3.16.x: 70f3ce0510af: mtd: spi-nor: make spi_nor_scan() take a chip type name, not spi_device_id
Cc: <stable@vger.kernel.org> # 3.16.x
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Drivers currently call spi_nor_match_id() and then spi_nor_scan().
This adds a dependency on struct spi_device_id which we want to
avoid. Make spi_nor_scan() do it for them.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
This "type" seems to be an extra hint for m25p80 about the flash. Some
archs register flash_platform_data with "name" set to "m25p80" and then
with a real flash name set in "type". It seems to be a trick specific
to the m25p80 so let's move it out of spi-nor.
Btw switch to the spi_nor_match_id instead of iterating spi_nor_ids.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Current situation with 4K sectors is quite messy. First of all, some
MTD "users" don't work with such small size. An example may be UBIFS
which requires 15 KiB erase blocks as a minimum. In theory spi-nor
should provide multiple erase regions and MTD "users" should use the
one they need. Unforunately that is not implemented.
In the result our flashes database in spi-nor is hackish. For some
flashes we pretend they don't support 4K sectors just because some
distribution uses UBIFS on it. This ofc leads to conflicts, like
Samsung using w25q128 with 4K sectors vs. OpenWrt requiring it to
pretend it's 64 KiB blocks only.
My idea (plan?) for fixing this situation:
1) Use real hw info (this requires a way for disabling 4K for now)
2) Provide detailed info about erase regions
3) Make UBIFS work with devices that support 4K sectors
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
It's a one-liner doing no magic and its name may be confusing because
it does not have to use JEDEC (e.g. when using alternative read_id).
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Acked-by: Huang Shijie <shijie8@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
This commit adds the support in the spi-nor driver of the Micron
M25PX80 flash, a 8 Mbit SPI flash from Micron.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Some new Micron flash chips require reading the flag status register to
determine when operations have completed.
Furthermore, chips with multi-die stacks of the 65nm 256Mb QSPI also
require reading the status register before reading the flag status
register.
This patch adds support for the flag status register in the n25q512ax3
and n25q00 Micron QSPI flash chips.
Signed-off-by: Graham Moore <grmoore@altera.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Spansion s25sl032p supports Dual and Quad SPI transfers, hence set the
SPI_NOR_DUAL_READ and SPI_NOR_QUAD_READ flags.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
There's no reason this can't be a module. Also, give SPI-NOR its own
submenu.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Reviewed-by: Marek Vasut <marex@denx.de>
serial_flash_cmds.h defines our opcodes a little differently. Let's
borrow its naming, since it's borrowed from the SFDP standard, and it's
more extensible.
This prepares us for merging serial_flash_cmds.h and spi-nor.h opcode
listing.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Acked-by: Huang Shijie <b32955@freescale.com>
Qualify these with a better namespace, and prepare them for use in more
drivers.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Acked-by: Huang Shijie <b32955@freescale.com>
Add the copyright information for spi-nor.c and spi-nor.h.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
(0) What is the QuadSPI controller?
The QuadSPI(Quad Serial Peripheral Interface) acts as an interface to
one single or two external serial flash devices, each with up to 4
bidirectional data lines.
(1) The QuadSPI controller is driven by the LUT(Look-up Table) registers.
The LUT registers are a look-up-table for sequences of instructions.
A valid sequence consists of four LUT registers.
(2) The definition of the LUT register shows below:
---------------------------------------------------
| INSTR1 | PAD1 | OPRND1 | INSTR0 | PAD0 | OPRND0 |
---------------------------------------------------
There are several types of INSTRx, such as:
CMD : the SPI NOR command.
ADDR : the address for the SPI NOR command.
DUMMY : the dummy cycles needed by the SPI NOR command.
....
There are several types of PADx, such as:
PAD1 : use a singe I/O line.
PAD2 : use two I/O lines.
PAD4 : use quad I/O lines.
....
(3) Test this driver with the JFFS2 and UBIFS:
For jffs2:
-------------
#flash_eraseall /dev/mtd0
#mount -t jffs2 /dev/mtdblock0 tmp
#bonnie++ -d tmp -u 0 -s 10 -r 5
For ubifs:
-------------
#flash_eraseall /dev/mtd0
#ubiattach /dev/ubi_ctrl -m 0
#ubimkvol /dev/ubi0 -N test -m
#mount -t ubifs ubi0:test tmp
#bonnie++ -d tmp -u 0 -s 10 -r 5
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Add the spi_nor_match_id() to find the proper spi_device_id with the
NOR flash's name in the spi_nor_ids table.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Acked-by: Marek Vasut <marex@denx.de>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
This patch cloned most of the m25p80.c. In theory, it adds a new spi-nor layer.
Before this patch, the layer is like:
MTD
------------------------
m25p80
------------------------
spi bus driver
------------------------
SPI NOR chip
After this patch, the layer is like:
MTD
------------------------
spi-nor
------------------------
m25p80
------------------------
spi bus driver
------------------------
SPI NOR chip
With the spi-nor controller driver(Freescale Quadspi), it looks like:
MTD
------------------------
spi-nor
------------------------
fsl-quadspi
------------------------
SPI NOR chip
New APIs:
spi_nor_scan: used to scan a spi-nor flash.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Acked-by: Marek Vasut <marex@denx.de>
[Brian: rebased to include additional m25p_ids[] entry]
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Andy Yan