Sync code to the same with tk4 pub/lts/0017-kabi, except deleted rue
and wujing. Partners can submit pull requests to this branch, and we
can pick the commits to tk4 pub/lts/0017-kabi easly.
Signed-off-by: Jianping Liu <frankjpliu@tencent.com>
Gitee limit the repo's size to 3GB, to reduce the size of the code,
sync codes to ock 5.4.119-20.0009.21 in one commit.
Signed-off-by: Jianping Liu <frankjpliu@tencent.com>
Currently, we don't have vfs nodes for querying the underlying flash name
and flash id. This information is important especially when we want to
know the flash detail of the defective system. In order to support the
query, we add mtd_debugfs_populate() to create two debugfs nodes
(ie. partname and partid). The upper driver can assign the pointer to
partname and partid before calling mtd_device_register().
Signed-off-by: Zhuohao Lee <zhuohao@chromium.org>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Added a flag to indicate a panic_write so that low level drivers can
use it to take required action where applicable, to ensure oops data
gets written to assigned mtd device.
Signed-off-by: Kamal Dasu <kdasu.kdev@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version this program is distributed in the
hope that it will be useful but without any warranty without even
the implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details you
should have received a copy of the gnu general public license along
with this program if not write to the free software foundation inc
51 franklin st fifth floor boston ma 02110 1301 usa
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 50 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190523091649.499889647@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
- Use struct_size() where appropriate
- mtd_{read,write}() as wrappers around mtd_{read,write}_oob()
- Fix misuse of PTR_ERR() in docg3
- Coding style improvements in mtdcore.c
SPI NOR changes:
Core changes:
- Add support of octal mode I/O transfer
- Add a bunch of SPI NOR entries to the flash_info table
SPI NOR controller driver changes:
- cadence-quadspi:
* Add support for Octal SPI controller
* write upto 8-bytes data in STIG mode
- mtk-quadspi:
* rename config to a common one
* add SNOR_HWCAPS_READ to spi_nor_hwcaps mask
- Add Tudor as SPI-NOR co-maintainer
NAND changes
NAND core changes:
- Fourth batch of fixes/cleanup to the raw NAND core impacting various
controller drivers (Sunxi, Marvell, MTK, TMIO, OMAP2).
- Checking the return code of nand_reset() and nand_readid_op().
- Removing ->legacy.erase and single_erase().
- Simplifying the locking.
- Several implicit fall through annotations.
Raw NAND controllers drivers changes:
- Fixing various possible object reference leaks (MTK, JZ4780, Atmel).
- ST:
* Adding support for STM32 FMC2 NAND flash controller.
- Meson:
* Adding support for Amlogic NAND flash controller.
- Denali:
* Several cleanup patches.
- Sunxi:
* Several cleanup patches.
- FSMC:
* Disabling NAND on remove().
* Resetting NAND timings on resume().
SPI-NAND drivers changes:
- Toshiba:
* Adding support for all Toshiba products.
- Macronix:
* Fixing ECC status read.
- Gigadevice:
* Adding support for GD5F1GQ4UExxG.
-----BEGIN PGP SIGNATURE-----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=wIHY
-----END PGP SIGNATURE-----
Merge tag 'mtd/for-5.1' of git://git.infradead.org/linux-mtd
Pull MTD updates from Boris Brezillon:
"Core MTD changes:
- Use struct_size() where appropriate
- mtd_{read,write}() as wrappers around mtd_{read,write}_oob()
- Fix misuse of PTR_ERR() in docg3
- Coding style improvements in mtdcore.c
SPI NOR changes:
Core changes:
- Add support of octal mode I/O transfer
- Add a bunch of SPI NOR entries to the flash_info table
SPI NOR controller driver changes:
- cadence-quadspi:
* Add support for Octal SPI controller
* write upto 8-bytes data in STIG mode
- mtk-quadspi:
* rename config to a common one
* add SNOR_HWCAPS_READ to spi_nor_hwcaps mask
- Add Tudor as SPI-NOR co-maintainer
NAND changes:
NAND core changes:
- Fourth batch of fixes/cleanup to the raw NAND core impacting
various controller drivers (Sunxi, Marvell, MTK, TMIO, OMAP2).
- Check the return code of nand_reset() and nand_readid_op().
- Remove ->legacy.erase and single_erase().
- Simplify the locking.
- Several implicit fall through annotations.
Raw NAND controllers drivers changes:
- Fix various possible object reference leaks (MTK, JZ4780, Atmel)
- ST:
* Add support for STM32 FMC2 NAND flash controller
- Meson:
* Add support for Amlogic NAND flash controller
- Denali:
* Several cleanup patches
- Sunxi:
* Several cleanup patches
- FSMC:
* Disable NAND on remove()
* Reset NAND timings on resume()
SPI-NAND drivers changes:
- Toshiba:
* Add support for all Toshiba products.
- Macronix:
* Fix ECC status read.
- Gigadevice:
* Add support for GD5F1GQ4UExxG"
* tag 'mtd/for-5.1' of git://git.infradead.org/linux-mtd: (64 commits)
mtd: spi-nor: Fix wrong abbreviation HWCPAS
mtd: spi-nor: cadence-quadspi: fix spelling mistake: "Couldnt't" -> "Couldn't"
mtd: spi-nor: Add support for en25qh64
mtd: spi-nor: Add support for MX25V8035F
mtd: spi-nor: Add support for EN25Q80A
mtd: spi-nor: cadence-quadspi: Add support for Octal SPI controller
dt-bindings: cadence-quadspi: Add new compatible for AM654 SoC
mtd: spi-nor: split s25fl128s into s25fl128s0 and s25fl128s1
mtd: spi-nor: cadence-quadspi: write upto 8-bytes data in STIG mode
mtd: spi-nor: Add support for mx25u3235f
mtd: rawnand: denali_dt: remove single anonymous clock support
mtd: rawnand: mtk: fix possible object reference leak
mtd: rawnand: jz4780: fix possible object reference leak
mtd: rawnand: atmel: fix possible object reference leak
mtd: rawnand: fsmc: Disable NAND on remove()
mtd: rawnand: fsmc: Reset NAND timings on resume()
mtd: spinand: Add support for GigaDevice GD5F1GQ4UExxG
mtd: rawnand: denali: remove unused dma_addr field from denali_nand_info
mtd: rawnand: denali: remove unused function argument 'raw'
mtd: rawnand: denali: remove unneeded denali_reset_irq() call
...
With this patch, we use the mtd->name instead of concatenating the name
with '0'.
Fixes: c4dfa25ab3 ("mtd: add support for reading MTD devices via the nvmem API")
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
Some sysfs functions have empty stray lines after the return statement.
This patch remove those empty lines.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Boris Brezillon <bbrezillon@kernel.org>
Signed-off-by: Boris Brezillon <bbrezillon@kernel.org>
mtd_{read,write}_oob() already take care of checking the params and
calling ->_{read,write}() or ->_{read,write}_oob() based on the
request and the operations supported by the MTD device.
No need to duplicate the logic, we can simply implement
mtd_{read,write}() as wrappers around mtd_{read,write}_oob().
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <bbrezillon@kernel.org>
Commit 20167b70c8 ("nvmem: use EOPNOTSUPP instead of ENOSYS") changed
the nvmem_register() ret code from ENOSYS to EOPNOTSUPP when
CONFIG_NVMEM is not enabled, but the check in mtd_nvmem_add() was not
adjusted accordingly.
Cc: Bartosz Golaszewski <brgl@bgdev.pl>
Cc: Alban Bedel <albeu@free.fr>
Fixes: c4dfa25ab3 ("mtd: add support for reading MTD devices via the nvmem API")
Reported-by: kernel test robot <rong.a.chen@intel.com>
Signed-off-by: Boris Brezillon <bbrezillon@kernel.org>
Reviewed-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Boris Brezillon <bbrezillon@kernel.org>
Here is the big set of char and misc driver patches for 4.21-rc1.
Lots of different types of driver things in here, as this tree seems to
be the "collection of various driver subsystems not big enough to have
their own git tree" lately.
Anyway, some highlights of the changes in here:
- binderfs: is it a rule that all driver subsystems will eventually
grow to have their own filesystem? Binder now has one to handle the
use of it in containerized systems. This was discussed at the
Plumbers conference a few months ago and knocked into mergable shape
very fast by Christian Brauner. Who also has signed up to be
another binder maintainer, showing a distinct lack of good judgement :)
- binder updates and fixes
- mei driver updates
- fpga driver updates and additions
- thunderbolt driver updates
- soundwire driver updates
- extcon driver updates
- nvmem driver updates
- hyper-v driver updates
- coresight driver updates
- pvpanic driver additions and reworking for more device support
- lp driver updates. Yes really, it's _finally_ moved to the proper
parallal port driver model, something I never thought I would see
happen. Good stuff.
- other tiny driver updates and fixes.
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXCZCUA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymF9QCgx/Z8Fj1qzGVGrIE4flXOi7pxOrgAoMqJEWtU
ywwL8M9suKDz7cZT9fWQ
=xxr6
-----END PGP SIGNATURE-----
Merge tag 'char-misc-4.21-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver updates from Greg KH:
"Here is the big set of char and misc driver patches for 4.21-rc1.
Lots of different types of driver things in here, as this tree seems
to be the "collection of various driver subsystems not big enough to
have their own git tree" lately.
Anyway, some highlights of the changes in here:
- binderfs: is it a rule that all driver subsystems will eventually
grow to have their own filesystem? Binder now has one to handle the
use of it in containerized systems.
This was discussed at the Plumbers conference a few months ago and
knocked into mergable shape very fast by Christian Brauner. Who
also has signed up to be another binder maintainer, showing a
distinct lack of good judgement :)
- binder updates and fixes
- mei driver updates
- fpga driver updates and additions
- thunderbolt driver updates
- soundwire driver updates
- extcon driver updates
- nvmem driver updates
- hyper-v driver updates
- coresight driver updates
- pvpanic driver additions and reworking for more device support
- lp driver updates. Yes really, it's _finally_ moved to the proper
parallal port driver model, something I never thought I would see
happen. Good stuff.
- other tiny driver updates and fixes.
All of these have been in linux-next for a while with no reported
issues"
* tag 'char-misc-4.21-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (116 commits)
MAINTAINERS: add another Android binder maintainer
intel_th: msu: Fix an off-by-one in attribute store
stm class: Add a reference to the SyS-T document
stm class: Fix a module refcount leak in policy creation error path
char: lp: use new parport device model
char: lp: properly count the lp devices
char: lp: use first unused lp number while registering
char: lp: detach the device when parallel port is removed
char: lp: introduce list to save port number
bus: qcom: remove duplicated include from qcom-ebi2.c
VMCI: Use memdup_user() rather than duplicating its implementation
char/rtc: Use of_node_name_eq for node name comparisons
misc: mic: fix a DMA pool free failure
ptp: fix an IS_ERR() vs NULL check
genwqe: Fix size check
binder: implement binderfs
binder: fix use-after-free due to ksys_close() during fdget()
bus: fsl-mc: remove duplicated include files
bus: fsl-mc: explicitly define the fsl_mc_command endianness
misc: ti-st: make array read_ver_cmd static, shrinks object size
...
Allow drivers that use the nvmem API to read data stored on MTD devices.
For this the mtd devices are registered as read-only NVMEM providers.
We don't support device tree systems for now.
Signed-off-by: Alban Bedel <albeu@free.fr>
[Bartosz:
- include linux/nvmem-provider.h
- set the name of the nvmem provider
- set no_of_node to true in nvmem_config
- don't check the return value of nvmem_unregister() - it cannot fail
- tweaked the commit message]
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Acked-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When allocating a new partition mtd subsystem runs internal tests in the
allocate_partition(). They may result in modifying specified flags (e.g.
dropping some /features/ like write access).
Those constraints don't have to be necessary true for subpartitions. It
may happen parent partition isn't block aligned (effectively disabling
write access) while subpartition may fit blocks nicely. In such case all
checks should be run again (starting with original flags value).
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
A Coverity robot reported an integer handling issue
(OVERFLOW_BEFORE_WIDEN) in the potentially overflowing expression:
(mtd_div_by_ws(mtd->size, mtd) - mtd_div_by_ws(offs, mtd)) *
mtd_oobavail(mtd, ops)
While such overflow will certainly never happen due to the numbers
handled, it is cleaner to fix this operation anyway.
The problem is that all the maths include 32-bit quantities, while the
result is stored in an explicit 64-bit value.
As maxooblen will just be compared with a size_t, let's change the
type of the variable to a size_t. This will not fix anything but will
clarify a bit the situation. Then, do an explicit cast to fix Coverity
warning.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Some MTD sublayers/drivers are implementing ->_read/write() and
not ->_read/write_oob().
While for NAND devices both are usually valid, for NOR devices, using
the _oob variant has no real meaning. But, as the MTD layer is supposed
to hide as much as possible the flash complexity to the user, there is
no reason to error out while it is just a matter of rewritting things
internally.
Add a fallback on mtd->_read() (resp. mtd->_write()) when the user calls
mtd_read_oob() (resp. mtd_write_oob()) while mtd->_read_oob() (resp.
mtd->_write_oob) is not implemented. There is already a fallback on the
_oob variant if the former is used.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Core changes:
- Add a sysfs attribute to expose available OOB size
Driver changes:
- Remove HAS_DMA dependency on various drivers
- Use dev_get_drvdata() instead of platform_get_drvdata() in docg3
- Replace msleep by usleep_range() in the dataflash driver
- Avoid VLA usage in nftl layers
- Remove useless .owner assignment in pismo
- Fix various issues in the CFI driver
- Improve TRX partition handling expose a DT compat for this part
parser
- Clarify OFFSET_CONTINUOUS meaning
NAND changes:
Core changes:
- Add Miquel as a NAND maintainer
- Add access mode to the nand_page_io_req struct
- Fix kernel-doc in rawnand.h
- Support bit-wise majority to recover from corrupted ONFI parameter
pages
- Stop checking FAIL bit after a SET_FEATURES, as documented in the
ONFI spec
Raw NAND Driver changes:
- Fix and cleanup the error path of many NAND controller drivers
- GPMI:
* Cleanup/simplification of a few aspects in the driver
* Take ECC setup specified in the DT into account
- sunxi: remove support for GPIO-based R/B polling
- MTK:
* Use of_device_get_match_data() instead of of_match_device()
* Add an entry in MAINTAINERS for this driver
* Fix nand-ecc-step-size and nand-ecc-strength description in the DT
bindings doc
- fsl_ifc: fix ->cmdfunc() to read more than one ONFI parameter page
OneNAND driver changes:
- samsung: use dev_get_drvdata() instead of platform_get_drvdata()
SPI NOR changes:
Core changes:
- Add support for a bunch of SPI NOR chips
- Clear EAR reg when switching to 3-byte addressing mode on Winbond
chips
SPI NOR controller driver changes:
- cadence: Add DMA support for direct mode reads
- hisi: Prefix a few functions with hisi_
- intel:
* Mark the driver as "dangerous" in Kconfig
* Fix atomic sequence handling
* Pass a 40us delay (instead of 0us) to readl_poll_timeout()
- fsl:
* fix a typo in a function name
* add support for IP variants embedded in the ls2080a and ls1080a
SoCs
- stm32: request exclusive control of the reset line
-----BEGIN PGP SIGNATURE-----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=cHjU
-----END PGP SIGNATURE-----
Merge tag 'mtd/for-4.18' of git://git.infradead.org/linux-mtd
Pull MTD updates from Boris Brezillon:
"Core changes:
- Add a sysfs attribute to expose available OOB size
Driver changes:
- Remove HAS_DMA dependency on various drivers
- Use dev_get_drvdata() instead of platform_get_drvdata() in docg3
- Replace msleep by usleep_range() in the dataflash driver
- Avoid VLA usage in nftl layers
- Remove useless .owner assignment in pismo
- Fix various issues in the CFI driver
- Improve TRX partition handling expose a DT compat for this part
parser
- Clarify OFFSET_CONTINUOUS meaning
NAND core changes:
- Add Miquel as a NAND maintainer
- Add access mode to the nand_page_io_req struct
- Fix kernel-doc in rawnand.h
- Support bit-wise majority to recover from corrupted ONFI parameter
pages
- Stop checking FAIL bit after a SET_FEATURES, as documented in the
ONFI spec
Raw NAND Driver changes:
- Fix and cleanup the error path of many NAND controller drivers
- GPMI:
+ Cleanup/simplification of a few aspects in the driver
+ Take ECC setup specified in the DT into account
- sunxi: remove support for GPIO-based R/B polling
- MTK:
+ Use of_device_get_match_data() instead of of_match_device()
+ Add an entry in MAINTAINERS for this driver
+ Fix nand-ecc-step-size and nand-ecc-strength description in the
DT bindings doc
- fsl_ifc: fix ->cmdfunc() to read more than one ONFI parameter page
OneNAND driver changes:
- samsung: use dev_get_drvdata() instead of platform_get_drvdata()
SPI NOR core changes:
- Add support for a bunch of SPI NOR chips
- Clear EAR reg when switching to 3-byte addressing mode on Winbond
chips
SPI NOR controller driver changes:
- cadence: Add DMA support for direct mode reads
- hisi: Prefix a few functions with hisi_
- intel:
+ Mark the driver as "dangerous" in Kconfig
+ Fix atomic sequence handling
+ Pass a 40us delay (instead of 0us) to readl_poll_timeout()
- fsl:
+ fix a typo in a function name
+ add support for IP variants embedded in the ls2080a and ls1080a
SoCs
- stm32: request exclusive control of the reset line"
* tag 'mtd/for-4.18' of git://git.infradead.org/linux-mtd: (66 commits)
mtd: nand: Pass mode information to nand_page_io_req
mtd: cfi_cmdset_0002: Change erase one block to enable XIP once
mtd: cfi_cmdset_0002: Change erase functions to check chip good only
mtd: cfi_cmdset_0002: Change erase functions to retry for error
mtd: cfi_cmdset_0002: Change definition naming to retry write operation
mtd: cfi_cmdset_0002: Change write buffer to check correct value
mtd: cmdlinepart: Update comment for introduction of OFFSET_CONTINUOUS
mtd: bcm47xxpart: add of_match_table with a new DT binding
dt-bindings: mtd: document Broadcom's BCM47xx partitions
mtd: spi-nor: Add support for EN25QH32
mtd: spi-nor: Add support for is25wp series chips
mtd: spi-nor: Add Winbond w25q32jv support
mtd: spi-nor: fsl-quadspi: add support for ls2080a/ls1080a
mtd: spi-nor: stm32-quadspi: explicitly request exclusive reset control
mtd: spi-nor: intel: provide a range for poll_timout
mtd: spi-nor: fsl-quadspi: fix api naming typo _init_ahb_read
mtd: spi-nor: intel-spi: Explicitly mark the driver as dangerous in Kconfig
mtd: spi-nor: intel-spi: Fix atomic sequence handling
mtd: rawnand: Do not check FAIL bit when executing a SET_FEATURES op
mtd: rawnand: use bit-wise majority to recover the ONFI param page
...
Variants of proc_create{,_data} that directly take a seq_file show
callback and drastically reduces the boilerplate code in the callers.
All trivial callers converted over.
Signed-off-by: Christoph Hellwig <hch@lst.de>
This commit slightly simplifies the code. Every parse_mtd_partitions()
caller (out of two existing ones) had to add partitions & cleanup parser
on its own. This moves that responsibility into the function.
That change also allows dropping struct mtd_partitions argument.
There is one minor behavior change caused by this cleanup. If
parse_mtd_partitions() fails to add partitions (add_mtd_partitions()
return an error) then mtd_device_parse_register() will still try to
add (register) fallback partitions. It's a real corner case affecting
one of uncommon error paths and shouldn't cause any harm.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Expose mtd OOB available size by sysfs file. Then users can get available
OOB size by accessing /sys/class/mtd/mtdX/oobavail.
Signed-off-by: Xiaolei Li <xiaolei.li@mediatek.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
In mtdcore.c, some function descriptions do not match function
definitions. Just fix these mismatches.
Signed-off-by: Xiaolei Li <xiaolei.li@mediatek.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
In the commit 2c77c57d22 ("mtd: move code adding master MTD out of
mtd_add_device_partitions()") behavior of mtd_device_parse_register()
has very slightly changed. It's a pretty non-significant order change
to match updated function behavior.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Reviewed-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
MTD users are no longer checking erase_info->state to determine if the
erase operation failed or succeeded. Moreover, mtd_erase_callback() is
now a NOP.
We can safely get rid of all mtd_erase_callback() calls and all
erase_info->state assignments. While at it, get rid of the
erase_info->state field, all MTD_ERASE_XXX definitions and the
mtd_erase_callback() function.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Richard Weinberger <richard@nod.at>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Bert Kenward <bkenward@solarflare.com>
---
Changes in v2:
- Address a few coding style issues (reported by Miquel)
- Remove comments that are no longer valid (reported by Miquel)
None of the mtd->_erase() implementations work in an asynchronous manner,
so let's simplify MTD users that call mtd_erase(). All they need to do
is check the value returned by mtd_erase() and assume that != 0 means
failure.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Richard Weinberger <richard@nod.at>
mtd_erase() can return an error before ->fail_addr is initialized to
MTD_FAIL_ADDR_UNKNOWN. Move this initialization at the very beginning
of the function.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Richard Weinberger <richard@nod.at>
This simplifies code a bit by:
1) Avoiding an extra (tiny) function
2) Checking for amount of parsed (found) partitions just once
3) Avoiding clearing/filling struct mtd_partitions manually
With this commit proper functions are called directly from the
mtd_device_parse_register(). It doesn't need to use minor tricks like
memsetting struct to 0 to trigger an expected
mtd_add_device_partitions() behavior.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
This change is a small cleanup of mtd_device_parse_register(). When
using MTD_PARTITIONED_MASTER it makes sure a master MTD is registered
before dealing with partitions. The advantage of this is not mixing
code handling master MTD with code handling partitions.
This commit doesn't change any behavior except from a slightly different
failure code path. The new code may need to call del_mtd_device when
something goes wrong.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Some devices do not implement ->_erase() or have an invalid ->erasesize
value. In this case, mtd_erase() should return -ENOTSUPP.
Note that the test is not done on the MTD_NO_ERASE flag because this
flag means 'erasing a block before writing to it is unnecessary',
not 'the erase operation is not supported'. Actually, some drivers are
setting the MTD_NO_ERASE flag but still implementing the ->_erase()
hook and setting a valid ->erasesize value.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Reviewed-by: Miquel Raynal <miquel.raynal@free-electrons.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Core changes:
* Rework core functions to avoid duplicating generic checks in
NAND/OneNAND sub-layers
* Update the MAINTAINERS entry to reflect the fact that MTD
maintainers now use a single git tree
Driver changes:
* CFI: use macros instead of inline functions to limit stack
usage and make KASAN happy
NAND changes:
Core changes:
* Fix NAND_CMD_NONE handling in nand_command[_lp]() hooks
* Introduce the ->exec_op() infrastructure
* Rework NAND buffers handling
* Fix ECC requirements for K9F4G08U0D
* Fix nand_do_read_oob() to return the number of bitflips
* Mark K9F1G08U0E as not supporting subpage writes
Driver changes:
* MTK: Rework the driver to support new IP versions
* OMAP OneNAND: Full rework to use new APIs (libgpio, dmaengine) and fix
DT support
* Marvell: Add a new driver to replace the pxa3xx one
SPI NOR changes:
Core changes:
* Add support to new ISSI and Cypress/Spansion memory parts.
* Fix support of Micron memories by checking error bits in the FSR.
* Fix update of block-protection bits by reading back the SR.
* Restore the internal state of the SPI flash memory when removing the
device.
Driver changes:
* Maintenance for Freescale, Intel and Metiatek drivers.
* Add support of the direct access mode for the Cadence QSPI controller.
-----BEGIN PGP SIGNATURE-----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=Mxo2
-----END PGP SIGNATURE-----
Merge tag 'mtd/for-4.16' of git://git.infradead.org/linux-mtd
Pull MTD updates from Boris Brezillon:
"MTD core changes:
- Rework core functions to avoid duplicating generic checks in
NAND/OneNAND sub-layers
- Update the MAINTAINERS entry to reflect the fact that MTD
maintainers now use a single git tree
MTD driver changes:
- CFI: use macros instead of inline functions to limit stack usage
and make KASAN happy
NAND core changes:
- Fix NAND_CMD_NONE handling in nand_command[_lp]() hooks
- Introduce the ->exec_op() infrastructure
- Rework NAND buffers handling
- Fix ECC requirements for K9F4G08U0D
- Fix nand_do_read_oob() to return the number of bitflips
- Mark K9F1G08U0E as not supporting subpage writes
NAND driver changes:
- MTK: Rework the driver to support new IP versions
- OMAP OneNAND: Full rework to use new APIs (libgpio, dmaengine) and
fix DT support
- Marvell: Add a new driver to replace the pxa3xx one
SPI NOR core changes:
- Add support to new ISSI and Cypress/Spansion memory parts.
- Fix support of Micron memories by checking error bits in the FSR.
- Fix update of block-protection bits by reading back the SR.
- Restore the internal state of the SPI flash memory when removing
the device.
SPI NOR driver changes:
- Maintenance for Freescale, Intel and Metiatek drivers.
- Add support of the direct access mode for the Cadence QSPI
controller"
* tag 'mtd/for-4.16' of git://git.infradead.org/linux-mtd: (93 commits)
mtd: nand: sunxi: Fix ECC strength choice
mtd: nand: gpmi: Fix subpage reads
mtd: nand: Fix build issues due to an anonymous union
mtd: nand: marvell: Fix missing memory allocation modifier
mtd: nand: marvell: remove redundant variable 'oob_len'
mtd: nand: marvell: fix spelling mistake: "suceed"-> "succeed"
mtd: onenand: omap2: Remove redundant dev_err call in omap2_onenand_probe()
mtd: Remove duplicate checks on mtd_oob_ops parameter
mtd: Fallback to ->_read/write_oob() when ->_read/write() is missing
mtd: mtdpart: Make ECC stat handling consistent
mtd: onenand: omap2: print resource using %pR format string
mtd: mtk-nor: modify functions' name more generally
mtd: onenand: samsung: remove incorrect __iomem annotation
MAINTAINERS: Add entry for Marvell NAND controller driver
ARM: OMAP2+: Remove gpmc-onenand
mtd: onenand: omap2: Configure driver from DT
mtd: onenand: omap2: Decouple DMA enabling from INT pin availability
mtd: onenand: omap2: Do not make delay for GPIO OMAP3 specific
mtd: onenand: omap2: Convert to use dmaengine for memcpy
mtd: onenand: omap2: Unify OMAP2 and OMAP3 DMA implementation
...
Some MTD sublayers/drivers are implementing ->_read/write_oob() and
provide dummy wrappers for their ->_read/write() implementations.
Let the core handle this case instead of duplicating the logic.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Acked-by: Brian Norris <computersforpeace@gmail.com>
Reviewed-by: Miquel Raynal <miquel.raynal@free-electrons.com>
Tested-by: Ladislav Michl <ladis@linux-mips.org>
When mtd->erasesize is 0 or mtd->_erase is NULL, that means the device
does not support the erase operation, which in turn means it should
have the MTD_NO_ERASE flag set.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Reviewed-by: Miquel Raynal <miquel.raynal@free-electrons.com>
The mtd_check_oob_ops() helper verifies if the operation defined by the
user is correct.
Fix the check that verifies if the entire requested area exists. This
check is too restrictive and will fail anytime the last data byte of the
very last page is included in an operation.
Fixes: 5cdd929da5 ("mtd: Add sanity checks in mtd_write/read_oob()")
Signed-off-by: Miquel Raynal <miquel.raynal@free-electrons.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
Unlike what's done in mtd_read/write(), there are no checks to make sure
the parameters passed to mtd_read/write_oob() are consistent, which
forces implementers of ->_read/write_oob() to do it, which in turn leads
to code duplication and possibly errors in the logic.
Do general sanity checks, like ops fields consistency and range checking.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Cc: Peter Pan <peterpandong@micron.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
The mtd->_point method is a superset of mtd->_get_unmapped_area.
Especially in the NOR flash case, the point method ensures the flash
memory is in array (data) mode and that it will stay that way which
is precisely what callers of mtd_get_unmapped_area() would expect.
Implement mtd_get_unmapped_area() in terms of mtd->_point now that all
drivers that provided a _get_unmapped_area method also have the _point
method implemented.
Signed-off-by: Nicolas Pitre <nico@linaro.org>
Reviewed-by: Richard Weinberger <richard@nod.at>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
Make this const as it is only stored in the type field of a device
structure, which is const.
Done using Coccinelle.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Several MTD devices are using debugfs entries created in the root.
This commit provides the means for a standardized subtree, creating
one "mtd" entry at root, and one entry per device inside it, named
after the device.
The tree is registered in add_mtd_device, and released in
del_mtd_device.
Devices docg3, mtdswap and nandsim were updated to use this subtree
instead of custom ones, and their entries were prefixed with the
drivers' names.
Signed-off-by: Mario J. Rugiero <mrugiero@gmail.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The code checks that ->_point is not NULL, but we should actually check
->_unpoint value which is dereferenced a few lines after the check.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Drop 'parent' argument of bdi_register() and bdi_register_va(). It is
always NULL.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Jens Axboe <axboe@fb.com>
MTD already allocates backing_dev_info dynamically. Convert it to use
generic infrastructure for this including proper refcounting. We drop
mtd->backing_dev_info as its only use was to pass mtd_bdi pointer from
one file into another and if we wanted to keep that in a clean way, we'd
have to make mtd hold and drop bdi reference as needed which seems
pointless for passing one global pointer...
CC: David Woodhouse <dwmw2@infradead.org>
CC: Brian Norris <computersforpeace@gmail.com>
CC: linux-mtd@lists.infradead.org
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Jens Axboe <axboe@fb.com>
The MTD backing dev info objects mtd_bdi was statically allocated.
So when MTD is built as a loadable module, this object fall in the
vmalloc address space.
The problem with that, is that the BDI APIs use wake_up_bit(), which calls
virt_to_page() to retrieve the memory zone of the page containing the
wait_queue to wake up, and virt_to_page() is not valid for vmalloc or
highmem addresses.
Fix this by allocating the BDI objects dynamically with kmalloc. The
objects now fall in the logical address space so that BDI APIs will
work in all cases (mtd builtin or module).
Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
Signed-off-by: Jim Baxter <jim_baxter@mentor.com>
Signed-off-by: Sandeep Jain <Sandeep_Jain@mentor.com>
Reviewed-by: Richard Weinberger <richard@nod.at>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
There is no need to initialize oobregion since it will be filled by
the iterator.
This function is called with mtd_ooblayout_free or mtd_ooblayout_ecc
for the iterator; both of them calls memset() to clear the oobregion.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
I hope this will make the code a little more readable.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
There is no need to initialize oobregion and section since they will
be filled by mtd_ooblayout_find_region().
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Kernel source files need not include <linux/kconfig.h> explicitly
because the top Makefile forces to include it with:
-include $(srctree)/include/linux/kconfig.h
This commit removes explicit includes except the following:
* arch/s390/include/asm/facilities_src.h
* tools/testing/radix-tree/linux/kernel.h
These two are used for host programs.
Link: http://lkml.kernel.org/r/1473656164-11929-1-git-send-email-yamada.masahiro@socionext.com
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
MLC and TLC NAND devices are using NAND cells exposing more than one bit,
but instead of attaching all the bits in a given cell to a single NAND
page, each bit is usually attached to a different page. This concept is
called 'page pairing', and has significant impacts on the flash storage
usage.
The main problem showed by these devices is that interrupting a page
program operation may not only corrupt the page we are programming
but also the page it is paired with, hence the need to expose to MTD
users the pairing scheme information.
The pairing APIs allows one to query pairing information attached to a
given page (here called wunit), or the other way around (the wunit
pointed by pairing information).
It also provides several helpers to help the conversion between absolute
offsets and wunits, and query the number of pairing groups.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Reviewed-by: Brian Norris <computersforpeace@gmail.com>
Now that all MTD drivers have moved to the mtd_ooblayout_ops model we can
safely remove the struct nand_ecclayout definition, and all the remaining
places where it was still used.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
ECC layout definitions are currently exposed using the nand_ecclayout
struct which embeds oobfree and eccpos arrays with predefined size.
This approach was acceptable when NAND chips were providing relatively
small OOB regions, but MLC and TLC now provide OOB regions of several
hundreds of bytes, which implies a non negligible overhead for everybody
even those who only need to support legacy NANDs.
Create an mtd_ooblayout_ops interface providing the same functionality
(expose the ECC and oobfree layout) without the need for this huge
structure.
The mtd->ecclayout is now deprecated and should be replaced by the
equivalent mtd_ooblayout_ops. In the meantime we provide a wrapper around
the ->ecclayout field to ease migration to this new model.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
In order to make the ecclayout definition completely dynamic we need to
rework the way the OOB layout are defined and iterated.
Create a few mtd_ooblayout_xxx() helpers to ease OOB bytes manipulation
and hide ecclayout internals to their users.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Now that we've added the MTD LED trigger, we need
to call each I/O path to ledtrig_mtd_activity.
Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
There's no reason for having mtd_write_oob inlined in mtd.h header.
Move it to mtdcore.c where it belongs.
Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Jianping Liu