A while ago, commit 9875201e10 ("rbd: fix use-after free of
rbd_dev->disk") fixed rbd unmap vs notify race by introducing
an exported wrapper for flushing notifies and sticking it into
do_rbd_remove().
A similar problem exists on the rbd map path, though: the watch is
registered in rbd_dev_image_probe(), while the disk is set up quite
a few steps later, in rbd_dev_device_setup(). Nothing prevents
a notify from coming in and crashing on a NULL rbd_dev->disk:
BUG: unable to handle kernel NULL pointer dereference at 0000000000000050
Call Trace:
[<ffffffffa0508344>] rbd_watch_cb+0x34/0x180 [rbd]
[<ffffffffa04bd290>] do_event_work+0x40/0xb0 [libceph]
[<ffffffff8109d5db>] process_one_work+0x17b/0x470
[<ffffffff8109e3ab>] worker_thread+0x11b/0x400
[<ffffffff8109e290>] ? rescuer_thread+0x400/0x400
[<ffffffff810a5acf>] kthread+0xcf/0xe0
[<ffffffff810b41b3>] ? finish_task_switch+0x53/0x170
[<ffffffff810a5a00>] ? kthread_create_on_node+0x140/0x140
[<ffffffff81645dd8>] ret_from_fork+0x58/0x90
[<ffffffff810a5a00>] ? kthread_create_on_node+0x140/0x140
RIP [<ffffffffa050828a>] rbd_dev_refresh+0xfa/0x180 [rbd]
If an error occurs during rbd map, we have to error out, potentially
tearing down a watch. Just like on rbd unmap, notifies have to be
flushed, otherwise rbd_watch_cb() may end up trying to read in the
image header after rbd_dev_image_release() has run:
Assertion failure in rbd_dev_header_info() at line 4722:
rbd_assert(rbd_image_format_valid(rbd_dev->image_format));
Call Trace:
[<ffffffff81cccee0>] ? rbd_parent_request_create+0x150/0x150
[<ffffffff81cd4e59>] rbd_dev_refresh+0x59/0x390
[<ffffffff81cd5229>] rbd_watch_cb+0x69/0x290
[<ffffffff81fde9bf>] do_event_work+0x10f/0x1c0
[<ffffffff81107799>] process_one_work+0x689/0x1a80
[<ffffffff811076f7>] ? process_one_work+0x5e7/0x1a80
[<ffffffff81132065>] ? finish_task_switch+0x225/0x640
[<ffffffff81107110>] ? pwq_dec_nr_in_flight+0x2b0/0x2b0
[<ffffffff81108c69>] worker_thread+0xd9/0x1320
[<ffffffff81108b90>] ? process_one_work+0x1a80/0x1a80
[<ffffffff8111b02d>] kthread+0x21d/0x2e0
[<ffffffff8111ae10>] ? kthread_stop+0x550/0x550
[<ffffffff82022802>] ret_from_fork+0x22/0x40
[<ffffffff8111ae10>] ? kthread_stop+0x550/0x550
RIP [<ffffffff81ccd8f9>] rbd_dev_header_info+0xa19/0x1e30
To fix this, a) check if RBD_DEV_FLAG_EXISTS is set before calling
revalidate_disk(), b) move ceph_osdc_flush_notifies() call into
rbd_dev_header_unwatch_sync() to cover rbd map error paths and c) turn
header read-in into a critical section. The latter also happens to
take care of rbd map foo@bar vs rbd snap rm foo@bar race.
Fixes: http://tracker.ceph.com/issues/15490
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Reviewed-by: Josh Durgin <jdurgin@redhat.com>
As of 5a60e87603, RBD object request
allocations are made via rbd_obj_request_create() with GFP_NOIO.
However, subsequent OSD request allocations in rbd_osd_req_create*()
use GFP_ATOMIC.
With heavy page cache usage (e.g. OSDs running on same host as krbd
client), rbd_osd_req_create() order-1 GFP_ATOMIC allocations have been
observed to fail, where direct reclaim would have allowed GFP_NOIO
allocations to succeed.
Cc: stable@vger.kernel.org # 3.18+
Suggested-by: Vlastimil Babka <vbabka@suse.cz>
Suggested-by: Neil Brown <neilb@suse.com>
Signed-off-by: David Disseldorp <ddiss@suse.de>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Use KMEM_CACHE() instead of kmem_cache_create() to simplify the code.
Signed-off-by: Geliang Tang <geliangtang@163.com>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Turn r_ops into a flexible array member to enable large, consisting of
up to 16 ops, OSD requests. The use case is scattered writeback in
cephfs and, as far as the kernel client is concerned, 16 is just a made
up number.
r_ops had size 3 for copyup+hint+write, but copyup is really a special
case - it can only happen once. ceph_osd_request_cache is therefore
stuffed with num_ops=2 requests, anything bigger than that is allocated
with kmalloc(). req_mempool is backed by ceph_osd_request_cache, which
means either num_ops=1 or num_ops=2 for use_mempool=true - all existing
users (ceph_writepages_start(), ceph_osdc_writepages()) are fine with
that.
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
This avoids defining large array of r_reply_op_{len,result} in
in struct ceph_osd_request.
Signed-off-by: Yan, Zheng <zyan@redhat.com>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
The rbd_dev_destroy() function tests whether its argument is NULL
and then returns immediately. Thus the test around the call is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Commit 4e752f0ab0 ("rbd: access snapshot context and mapping size
safely") moved ceph_get_snap_context() out of rbd_img_request_create()
and into rbd_queue_workfn(), adding a ceph_put_snap_context() to the
error path in rbd_queue_workfn(). However, rbd_img_request_create()
consumes a ref on snapc, so calling ceph_put_snap_context() after
a successful rbd_img_request_create() leads to an extra put. Fix it.
Cc: stable@vger.kernel.org # 3.18+
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Reviewed-by: Josh Durgin <jdurgin@redhat.com>
Commit d1cf578845 ("rbd: set mapping info earlier") defined
rbd_dev_mapping_clear(), but, just a few days after, commit
f35a4dee14 ("rbd: set the mapping size and features later") moved
rbd_dev_mapping_set() calls and added another rbd_dev_mapping_clear()
call instead of moving the old one. Around the same time, another
duplicate was introduced in rbd_dev_device_release() - kill both.
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
No point in providing an empty device_type::release callback and then
setting device::release for each rbd_dev dynamically.
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
struct rbd_device has struct device embedded in it, which means it's
part of kobject universe and has an unpredictable life cycle. Freeing
its memory outside of the release callback is flawed, yet commits
200a6a8be5 ("rbd: don't destroy rbd_dev in device release function")
and 8ad42cd0c0 ("rbd: don't have device release destroy rbd_dev")
moved rbd_dev_destroy() out to rbd_dev_image_release().
This commit reverts most of that, the key points are:
- rbd_dev->dev is initialized in rbd_dev_create(), making it possible
to use rbd_dev_destroy() - which is just a put_device() - both before
we register with device core and after.
- rbd_dev_release() (the release callback) is the only place we
kfree(rbd_dev). It's also where we do module_put(), keeping the
module unload race window as small as possible.
- We pin the module in rbd_dev_create(), but only for mapping
rbd_dev-s. Moving image related stuff out of struct rbd_device into
another struct which isn't tied with sysfs and device core is long
overdue, but until that happens, this will keep rbd module refcount
(which users can observe with lsmod) sane.
Fixes: http://tracker.ceph.com/issues/12697
Cc: Alex Elder <elder@linaro.org>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Returning pool id (i.e. >= 0) from a sysfs ->store() callback makes
userspace think it needs to retry the write. Fix it - it's a leftover
from the times when the equivalent of rbd_dev_create() was the first
action in rbd_add().
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
rbd requires stable pages, as it performs a crc of the page data before
they are send to the OSDs.
But since kernel 3.9 (patch 1d1d1a7672
"mm: only enforce stable page writes if the backing device requires
it") it is not assumed anymore that block devices require stable pages.
This patch sets the necessary flag to get stable pages back for rbd.
In a ceph installation that provides multiple ext4 formatted rbd
devices "bad crc" messages appeared regularly (ca 1 message every 1-2
minutes on every OSD that provided the data for the rbd) in the
OSD-logs before this patch. After this patch this messages are pretty
much gone (only ca 1-2 / month / OSD).
Cc: stable@vger.kernel.org # 3.9+, needs backporting
Signed-off-by: Ronny Hegewald <Ronny.Hegewald@online.de>
[idryomov@gmail.com: require stable pages only in crc case, changelog]
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Mapping an image with a long parent chain (e.g. image foo, whose parent
is bar, whose parent is baz, etc) currently leads to a kernel stack
overflow, due to the following recursion in the reply path:
rbd_osd_req_callback()
rbd_obj_request_complete()
rbd_img_obj_callback()
rbd_img_parent_read_callback()
rbd_obj_request_complete()
...
Limit the parent chain to 16 images, which is ~5K worth of stack. When
the above recursion is eliminated, this limit can be lifted.
Fixes: http://tracker.ceph.com/issues/12538
Cc: stable@vger.kernel.org # 3.10+, needs backporting for < 4.2
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Reviewed-by: Josh Durgin <jdurgin@redhat.com>
Currently we leak parent_spec and trigger a "parent reference
underflow" warning if rbd_dev_create() in rbd_dev_probe_parent() fails.
The problem is we take the !parent out_err branch and that only drops
refcounts; parent_spec that would've been freed had we called
rbd_dev_unparent() remains and triggers rbd_warn() in
rbd_dev_parent_put() - at that point we have parent_spec != NULL and
parent_ref == 0, so counter ends up being -1 after the decrement.
Redo rbd_dev_probe_parent() to fix this.
Cc: stable@vger.kernel.org # 3.10+, needs backporting for < 4.2
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Reviewed-by: Alex Elder <elder@linaro.org>
This covers only the simplest case - an object size sized write, but
it's still useful in tiering setups when EC is used for the base tier
as writefull op can be proxied, saving an object promotion.
Even though updating ceph_osdc_new_request() to allow writefull should
just be a matter of fixing an assert, I didn't do it because its only
user is cephfs. All other sites were updated.
Reflects ceph.git commit 7bfb7f9025a8ee0d2305f49bf0336d2424da5b5b.
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Reviewed-by: Alex Elder <elder@linaro.org>
Commit 30e2bc08b2 ("Revert "block: remove artifical max_hw_sectors
cap"") restored a clamp on max_sectors. It's now 2560 sectors instead
of 1024, but it's not good enough: we set max_hw_sectors to rbd object
size because we don't want object sized I/Os to be split, and the
default object size is 4M.
So, set max_sectors to max_hw_sectors in rbd at queue init time.
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Reviewed-by: Alex Elder <elder@linaro.org>
Pull Ceph update from Sage Weil:
"There are a few fixes for snapshot behavior with CephFS and support
for the new keepalive protocol from Zheng, a libceph fix that affects
both RBD and CephFS, a few bug fixes and cleanups for RBD from Ilya,
and several small fixes and cleanups from Jianpeng and others"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client:
ceph: improve readahead for file holes
ceph: get inode size for each append write
libceph: check data_len in ->alloc_msg()
libceph: use keepalive2 to verify the mon session is alive
rbd: plug rbd_dev->header.object_prefix memory leak
rbd: fix double free on rbd_dev->header_name
libceph: set 'exists' flag for newly up osd
ceph: cleanup use of ceph_msg_get
ceph: no need to get parent inode in ceph_open
ceph: remove the useless judgement
ceph: remove redundant test of head->safe and silence static analysis warnings
ceph: fix queuing inode to mdsdir's snaprealm
libceph: rename con_work() to ceph_con_workfn()
libceph: Avoid holding the zero page on ceph_msgr_slab_init errors
libceph: remove the unused macro AES_KEY_SIZE
ceph: invalidate dirty pages after forced umount
ceph: EIO all operations after forced umount
Need to free object_prefix when rbd_dev_v2_snap_context() fails, but
only if this is the first time we are reading in the header.
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Reviewed-by: Alex Elder <elder@linaro.org>
If rbd_dev_image_probe() in rbd_dev_probe_parent() fails, header_name
is freed twice: once in rbd_dev_probe_parent() and then in its caller
rbd_dev_image_probe() (rbd_dev_image_probe() is called recursively to
handle parent images).
rbd_dev_probe_parent() is responsible for probing the parent, so it
shouldn't muck with clone's fields.
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Reviewed-by: Alex Elder <elder@linaro.org>
Pull core block updates from Jens Axboe:
"This first core part of the block IO changes contains:
- Cleanup of the bio IO error signaling from Christoph. We used to
rely on the uptodate bit and passing around of an error, now we
store the error in the bio itself.
- Improvement of the above from myself, by shrinking the bio size
down again to fit in two cachelines on x86-64.
- Revert of the max_hw_sectors cap removal from a revision again,
from Jeff Moyer. This caused performance regressions in various
tests. Reinstate the limit, bump it to a more reasonable size
instead.
- Make /sys/block/<dev>/queue/discard_max_bytes writeable, by me.
Most devices have huge trim limits, which can cause nasty latencies
when deleting files. Enable the admin to configure the size down.
We will look into having a more sane default instead of UINT_MAX
sectors.
- Improvement of the SGP gaps logic from Keith Busch.
- Enable the block core to handle arbitrarily sized bios, which
enables a nice simplification of bio_add_page() (which is an IO hot
path). From Kent.
- Improvements to the partition io stats accounting, making it
faster. From Ming Lei.
- Also from Ming Lei, a basic fixup for overflow of the sysfs pending
file in blk-mq, as well as a fix for a blk-mq timeout race
condition.
- Ming Lin has been carrying Kents above mentioned patches forward
for a while, and testing them. Ming also did a few fixes around
that.
- Sasha Levin found and fixed a use-after-free problem introduced by
the bio->bi_error changes from Christoph.
- Small blk cgroup cleanup from Viresh Kumar"
* 'for-4.3/core' of git://git.kernel.dk/linux-block: (26 commits)
blk: Fix bio_io_vec index when checking bvec gaps
block: Replace SG_GAPS with new queue limits mask
block: bump BLK_DEF_MAX_SECTORS to 2560
Revert "block: remove artifical max_hw_sectors cap"
blk-mq: fix race between timeout and freeing request
blk-mq: fix buffer overflow when reading sysfs file of 'pending'
Documentation: update notes in biovecs about arbitrarily sized bios
block: remove bio_get_nr_vecs()
fs: use helper bio_add_page() instead of open coding on bi_io_vec
block: kill merge_bvec_fn() completely
md/raid5: get rid of bio_fits_rdev()
md/raid5: split bio for chunk_aligned_read
block: remove split code in blkdev_issue_{discard,write_same}
btrfs: remove bio splitting and merge_bvec_fn() calls
bcache: remove driver private bio splitting code
block: simplify bio_add_page()
block: make generic_make_request handle arbitrarily sized bios
blk-cgroup: Drop unlikely before IS_ERR(_OR_NULL)
block: don't access bio->bi_error after bio_put()
block: shrink struct bio down to 2 cache lines again
...
As generic_make_request() is now able to handle arbitrarily sized bios,
it's no longer necessary for each individual block driver to define its
own ->merge_bvec_fn() callback. Remove every invocation completely.
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Lars Ellenberg <drbd-dev@lists.linbit.com>
Cc: drbd-user@lists.linbit.com
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Yehuda Sadeh <yehuda@inktank.com>
Cc: Sage Weil <sage@inktank.com>
Cc: Alex Elder <elder@kernel.org>
Cc: ceph-devel@vger.kernel.org
Cc: Alasdair Kergon <agk@redhat.com>
Cc: Mike Snitzer <snitzer@redhat.com>
Cc: dm-devel@redhat.com
Cc: Neil Brown <neilb@suse.de>
Cc: linux-raid@vger.kernel.org
Cc: Christoph Hellwig <hch@infradead.org>
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>
Acked-by: NeilBrown <neilb@suse.de> (for the 'md' bits)
Acked-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Kent Overstreet <kent.overstreet@gmail.com>
[dpark: also remove ->merge_bvec_fn() in dm-thin as well as
dm-era-target, and resolve merge conflicts]
Signed-off-by: Dongsu Park <dpark@posteo.net>
Signed-off-by: Ming Lin <ming.l@ssi.samsung.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
For write/discard obj_requests that involved a copyup method call, the
opcode of the first op is CEPH_OSD_OP_CALL and the ->callback is
rbd_img_obj_copyup_callback(). The latter frees copyup pages, sets
->xferred and delegates to rbd_img_obj_callback(), the "normal" image
object callback, for reporting to block layer and putting refs.
rbd_osd_req_callback() however treats CEPH_OSD_OP_CALL as a trivial op,
which means obj_request is marked done in rbd_osd_trivial_callback(),
*before* ->callback is invoked and rbd_img_obj_copyup_callback() has
a chance to run. Marking obj_request done essentially means giving
rbd_img_obj_callback() a license to end it at any moment, so if another
obj_request from the same img_request is being completed concurrently,
rbd_img_obj_end_request() may very well be called on such prematurally
marked done request:
<obj_request-1/2 reply>
handle_reply()
rbd_osd_req_callback()
rbd_osd_trivial_callback()
rbd_obj_request_complete()
rbd_img_obj_copyup_callback()
rbd_img_obj_callback()
<obj_request-2/2 reply>
handle_reply()
rbd_osd_req_callback()
rbd_osd_trivial_callback()
for_each_obj_request(obj_request->img_request) {
rbd_img_obj_end_request(obj_request-1/2)
rbd_img_obj_end_request(obj_request-2/2) <--
}
Calling rbd_img_obj_end_request() on such a request leads to trouble,
in particular because its ->xfferred is 0. We report 0 to the block
layer with blk_update_request(), get back 1 for "this request has more
data in flight" and then trip on
rbd_assert(more ^ (which == img_request->obj_request_count));
with rhs (which == ...) being 1 because rbd_img_obj_end_request() has
been called for both requests and lhs (more) being 1 because we haven't
got a chance to set ->xfferred in rbd_img_obj_copyup_callback() yet.
To fix this, leverage that rbd wants to call class methods in only two
cases: one is a generic method call wrapper (obj_request is standalone)
and the other is a copyup (obj_request is part of an img_request). So
make a dedicated handler for CEPH_OSD_OP_CALL and directly invoke
rbd_img_obj_copyup_callback() from it if obj_request is part of an
img_request, similar to how CEPH_OSD_OP_READ handler invokes
rbd_img_obj_request_read_callback().
Since rbd_img_obj_copyup_callback() is now being called from the OSD
request callback (only), it is renamed to rbd_osd_copyup_callback().
Cc: Alex Elder <elder@linaro.org>
Cc: stable@vger.kernel.org # 3.10+, needs backporting for < 3.18
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Reviewed-by: Alex Elder <elder@linaro.org>
Some drivers use it now, others just set the limits field manually.
But in preparation for splitting this into a hard and soft limit,
ensure that they all call the proper function for setting the hw
limit for discards.
Reviewed-by: Jeff Moyer <jmoyer@redhat.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
rbd_obj_request_create() is called on the main I/O path, so we need to
use GFP_NOIO to make sure allocation doesn't blow back on us. Not all
callers need this, but I'm still hardcoding the flag inside rather than
making it a parameter because a) this is going to stable, and b) those
callers shouldn't really use rbd_obj_request_create() and will be fixed
in the future.
More memory allocation fixes will follow.
Cc: stable@vger.kernel.org # 3.10+
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Reviewed-by: Alex Elder <elder@linaro.org>
nr_requests (/sys/block/rbd<id>/queue/nr_requests) is pretty much
irrelevant in blk-mq case because each driver sets its own max depth
that it can handle and that's the number of tags that gets preallocated
on setup. Users can't increase queue depth beyond that value via
writing to nr_requests.
For rbd we are happy with the default BLKDEV_MAX_RQ (128) for most
cases but we want to give users the opportunity to increase it.
Introduce a new per-device queue_depth option to do just that:
$ sudo rbd map -o queue_depth=1024 ...
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Reviewed-by: Alex Elder <elder@linaro.org>
The default queue_limits::max_segments value (BLK_MAX_SEGMENTS = 128)
unnecessarily limits bio sizes to 512k (assuming 4k pages). rbd, being
a virtual block device, doesn't have any restrictions on the number of
physical segments, so bump max_segments to max_hw_sectors, in theory
allowing a sector per segment (although the only case this matters that
I can think of is some readv/writev style thing). In practice this is
going to give us 1M bios - the number of segments in a bio is limited
in bio_get_nr_vecs() by BIO_MAX_PAGES = 256.
Note that this doesn't result in any improvement on a typical direct
sequential test. This is because on a box with a not too badly
fragmented memory the default BLK_MAX_SEGMENTS is enough to see nice
rbd object size sized requests. The only difference is the size of
bios being merged - 512k vs 1M for something like
$ dd if=/dev/zero of=/dev/rbd0 oflag=direct bs=$RBD_OBJ_SIZE
$ dd if=/dev/rbd0 iflag=direct of=/dev/null bs=$RBD_OBJ_SIZE
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Reviewed-by: Alex Elder <elder@linaro.org>
As part of unmap sequence, kernel client has to talk to the OSDs to
teardown watch on the header object. If none of the OSDs are available
it would hang forever, until interrupted by a signal - when that
happens we follow through with the rest of unmap procedure (i.e.
unregister the device and put all the data structures) and the unmap is
still considired successful (rbd cli tool exits with 0). The watch on
the userspace side should eventually timeout so that's fine.
This isn't very nice, because various userspace tools (pacemaker rbd
resource agent, for example) then have to worry about setting up their
own timeouts. Timeout it with mount_timeout (60 seconds by default).
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Reviewed-by: Alex Elder <elder@linaro.org>
Reviewed-by: Sage Weil <sage@redhat.com>
There are currently three libceph-level timeouts that the user can
specify on mount: mount_timeout, osd_idle_ttl and osdkeepalive. All of
these are in seconds and no checking is done on user input: negative
values are accepted, we multiply them all by HZ which may or may not
overflow, arbitrarily large jiffies then get added together, etc.
There is also a bug in the way mount_timeout=0 is handled. It's
supposed to mean "infinite timeout", but that's not how wait.h APIs
treat it and so __ceph_open_session() for example will busy loop
without much chance of being interrupted if none of ceph-mons are
there.
Fix all this by verifying user input, storing timeouts capped by
msecs_to_jiffies() in jiffies and using the new ceph_timeout_jiffies()
helper for all user-specified waits to handle infinite timeouts
correctly.
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Reviewed-by: Alex Elder <elder@linaro.org>
When we end I/O struct request with error, we need to pass
obj_request->length as @nr_bytes so that the entire obj_request worth
of bytes is completed. Otherwise block layer ends up confused and we
trip on
rbd_assert(more ^ (which == img_request->obj_request_count));
in rbd_img_obj_callback() due to more being true no matter what. We
already do it in most cases but we are missing some, in particular
those where we don't even get a chance to submit any obj_requests, due
to an early -ENOMEM for example.
A number of obj_request->xferred assignments seem to be redundant but
I haven't touched any of obj_request->xferred stuff to keep this small
and isolated.
Cc: Alex Elder <elder@linaro.org>
Cc: stable@vger.kernel.org # 3.10+
Reported-by: Shawn Edwards <lesser.evil@gmail.com>
Reviewed-by: Sage Weil <sage@redhat.com>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Set QUEUE_FLAG_NONROT. Following commit b277da0a8a ("block: disable
entropy contributions for nonrot devices") we should also clear
QUEUE_FLAG_ADD_RANDOM, but it's off by default for blk-mq drivers, so
just note it in the comment.
Also remove physical block size assignment - no sense in repeating
defaults that are not going to change.
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
This converts the rbd driver to use the blk-mq infrastructure. Except
for switching to a per-request work item this is almost mechanical.
This was tested by Alexandre DERUMIER in November, and found to give
him 120000 iops, although the only comparism available was an old
3.10 kernel which gave 80000iops.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Alex Elder <elder@linaro.org>
[idryomov@gmail.com: context, blk_mq_init_queue() EH]
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
If the clone is resized down to 0, it becomes standalone. If such
resize is carried over while an image is mapped we would detect this
and call rbd_dev_parent_put() which means "let go of all parent state,
including the spec(s) of parent images(s)". This leads to a mismatch
between "rbd info" and sysfs parent fields, so a fix is in order.
# rbd create --image-format 2 --size 1 foo
# rbd snap create foo@snap
# rbd snap protect foo@snap
# rbd clone foo@snap bar
# DEV=$(rbd map bar)
# rbd resize --allow-shrink --size 0 bar
# rbd resize --size 1 bar
# rbd info bar | grep parent
parent: rbd/foo@snap
Before:
# cat /sys/bus/rbd/devices/0/parent
(no parent image)
After:
# cat /sys/bus/rbd/devices/0/parent
pool_id 0
pool_name rbd
image_id 10056b8b4567
image_name foo
snap_id 2
snap_name snap
overlap 0
Signed-off-by: Ilya Dryomov <idryomov@redhat.com>
Reviewed-by: Josh Durgin <jdurgin@redhat.com>
Reviewed-by: Alex Elder <elder@linaro.org>
header_rwsem should be released on errors. Also remove useless
rbd_dev->mapping.size != rbd_dev->header.image_size test.
Signed-off-by: Ilya Dryomov <idryomov@redhat.com>
It's been largely superseded by dup_token() and unused for over
2 years, identified by cppcheck.
Signed-off-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
[idryomov@redhat.com: changelog]
Signed-off-by: Ilya Dryomov <idryomov@redhat.com>
This effectively reverts the last hunk of 392a9dad7e ("rbd: detect
when clone image is flattened").
The problem with parent_overlap != 0 condition is that it's possible
and completely valid to have an image with parent_overlap == 0 whose
parent state needs to be cleaned up on unmap. The next commit, which
drops the "clone image now standalone" logic, opens up another window
of opportunity to hit this, but even without it
# cat parent-ref.sh
#!/bin/bash
rbd create --image-format 2 --size 1 foo
rbd snap create foo@snap
rbd snap protect foo@snap
rbd clone foo@snap bar
rbd resize --allow-shrink --size 0 bar
rbd resize --size 1 bar
DEV=$(rbd map bar)
rbd unmap $DEV
leaves rbd_device/rbd_spec/etc and rbd_client along with ceph_client
hanging around.
My thinking behind calling rbd_dev_parent_put() unconditionally is that
there shouldn't be any requests in flight at that point in time as we
are deep into unmap sequence. Hence, even if rbd_dev_unparent() caused
by flatten is delayed by in-flight requests, it will have finished by
the time we reach rbd_dev_unprobe() caused by unmap, thus turning
unconditional rbd_dev_parent_put() into a no-op.
Fixes: http://tracker.ceph.com/issues/10352
Cc: stable@vger.kernel.org # 3.11+
Signed-off-by: Ilya Dryomov <idryomov@redhat.com>
Reviewed-by: Josh Durgin <jdurgin@redhat.com>
Reviewed-by: Alex Elder <elder@linaro.org>
The comment for rbd_dev_parent_get() said
* We must get the reference before checking for the overlap to
* coordinate properly with zeroing the parent overlap in
* rbd_dev_v2_parent_info() when an image gets flattened. We
* drop it again if there is no overlap.
but the "drop it again if there is no overlap" part was missing from
the implementation. This lead to absurd parent_ref values for images
with parent_overlap == 0, as parent_ref was incremented for each
img_request and virtually never decremented.
Fix this by leveraging the fact that refresh path calls
rbd_dev_v2_parent_info() under header_rwsem and use it for read in
rbd_dev_parent_get(), instead of messing around with atomics. Get rid
of barriers in rbd_dev_v2_parent_info() while at it - I don't see what
they'd pair with now and I suspect we are in a pretty miserable
situation as far as proper locking goes regardless.
Cc: stable@vger.kernel.org # 3.11+
Signed-off-by: Ilya Dryomov <idryomov@redhat.com>
Reviewed-by: Josh Durgin <jdurgin@redhat.com>
Reviewed-by: Alex Elder <elder@linaro.org>
CEPH_OSD_OP_DELETE is not an extent op, stop treating it as such. This
sneaked in with discard patches - it's one of the three osd ops (the
other two are CEPH_OSD_OP_TRUNCATE and CEPH_OSD_OP_ZERO) that discard
is implemented with.
Signed-off-by: Ilya Dryomov <idryomov@redhat.com>
Reviewed-by: Alex Elder <elder@linaro.org>
The functions ceph_put_snap_context() and iput() test whether their
argument is NULL and then return immediately. Thus the test around the
call is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
[idryomov@redhat.com: squashed rbd.c hunk, changelog]
Signed-off-by: Ilya Dryomov <idryomov@redhat.com>
When we fail to allocate page vector in rbd_obj_read_sync() we just
basically ignore the problem and continue which will result in an oops
later. Fix the problem by returning proper error.
CC: Yehuda Sadeh <yehuda@inktank.com>
CC: Sage Weil <sage@inktank.com>
CC: ceph-devel@vger.kernel.org
CC: stable@vger.kernel.org
Coverity-id: 1226882
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Ilya Dryomov <idryomov@redhat.com>
Using one queue per device doesn't make much sense given that our
workfn processes "devices" and not "requests". Switch to a single
workqueue for all devices.
Signed-off-by: Ilya Dryomov <idryomov@redhat.com>
Reviewed-by: Sage Weil <sage@redhat.com>
Need to use WQ_MEM_RECLAIM for our workqueues to prevent I/O lockups
under memory pressure - we sit on the memory reclaim path.
Cc: stable@vger.kernel.org # 3.17, needs backporting for 3.16
Signed-off-by: Ilya Dryomov <idryomov@redhat.com>
Tested-by: Micha Krause <micha@krausam.de>
Reviewed-by: Sage Weil <sage@redhat.com>
max_discard_sectors must be set for the queue to support discard.
Operations implementing discard for rbd zero data, so report that.
Signed-off-by: Josh Durgin <josh.durgin@inktank.com>
Only allocate two osd ops for discard requests, since the
preallocation hint is only added for regular writes. Use
rbd_img_obj_request_fill() to recreate the original write or discard
osd operations, isolating that logic to one place, and change the
assert in rbd_osd_req_create_copyup() to accept discard requests as
well.
Signed-off-by: Josh Durgin <josh.durgin@inktank.com>
rbd_img_request_fill() creates a ceph_osd_request and has logic for
adding the appropriate osd ops to it based on the request type and
image properties.
For layered images, the original rbd_obj_request is resent with a
copyup operation in front, using a new ceph_osd_request. The logic for
adding the original operations should be the same as when first
sending them, so move it to a helper function.
op_type only needs to be checked once, so create a helper for that as
well and call it outside the loop in rbd_img_request_fill().
Signed-off-by: Josh Durgin <josh.durgin@inktank.com>
Discard requests are a form of write, so they should go through the
same process as plain write requests and trigger copy-on-write for
layered images.
Signed-off-by: Josh Durgin <josh.durgin@inktank.com>
Discard may try to delete an object from a non-layered image that does not exist.
If this occurs, the image already has no data in that range, so change the
result to success.
Signed-off-by: Josh Durgin <josh.durgin@inktank.com>
Discards take a reference to the snapshot context of an image when
they are created. This reference needs to be cleaned up when the
request is done just as it is for regular writes.
Signed-off-by: Josh Durgin <josh.durgin@inktank.com>
In rbd_img_request_fill() the image size is only checked to determine
whether we can truncate an object instead of zeroing it for discard
requests. Take rbd_dev->header_rwsem while reading the image size, and
move this read into the discard check, so that non-discard ops don't
need to take the semaphore in this function.
Signed-off-by: Josh Durgin <josh.durgin@inktank.com>
This patch add the discard support for rbd driver.
There are three types operation in the driver:
1. The objects would be removed if they completely contained
within the discard range.
2. The objects would be truncated if they partly contained within
the discard range, and align with their boundary.
3. Others would be zeroed.
A discard request from blkdev_issue_discard() is defined which
REQ_WRITE and REQ_DISCARD both marked and no data, so we must
check the REQ_DISCARD first when getting the request type.
This resolve:
http://tracker.ceph.com/issues/190
[ Ilya Dryomov: This is incomplete and somewhat buggy, see follow up
commits by Josh Durgin for refinements and fixes which weren't
folded in to preserve authorship. ]
Signed-off-by: Guangliang Zhao <lucienchao@gmail.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
Reviewed-by: Alex Elder <elder@linaro.org>
It could only handle the read and write operations now,
extend it for the coming discard support.
Signed-off-by: Guangliang Zhao <lucienchao@gmail.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
Reviewed-by: Alex Elder <elder@linaro.org>
It need to copyup the parent's content when layered writing,
but an entire object write would overwrite it, so skip it.
Signed-off-by: Guangliang Zhao <lucienchao@gmail.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
Reviewed-by: Alex Elder <elder@linaro.org>
These fields may both change while the image is mapped if a snapshot
is created or deleted or the image is resized. They are guarded by
rbd_dev->header_rwsem, so hold that while reading them, and store a
local copy to refer to outside of the critical section. The local copy
will stay consistent since the snapshot context is reference counted,
and the mapping size is just a u64. This prevents torn loads from
giving us inconsistent values.
Move reading header.snapc into the caller of rbd_img_request_create()
so that we only need to take the semaphore once. The read-only caller,
rbd_parent_request_create() can just pass NULL for snapc, since the
snapshot context is only relevant for writes.
Signed-off-by: Josh Durgin <josh.durgin@inktank.com>
Trying to map an image out of a pool for which we don't have an 'x'
permission bit fails with -ERANGE from ceph_extract_encoded_string()
due to an unsigned vs signed bug. Fix it and get rid of the -EINVAL
sink, thus propagating rbd::get_id cls method errors. (I've seen
a bunch of unexplained -ERANGE reports, I bet this is it).
Signed-off-by: Ilya Dryomov <ilya.dryomov@inktank.com>
Reviewed-by: Alex Elder <elder@linaro.org>
Fix to return -ENOMEM from the workqueue alloc error handling
case instead of 0, as done elsewhere in this function.
Reviewed-by: Alex Elder <elder@linaro.org>
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
drivers/block/rbd.c: In function ‘rbd_dev_device_setup’:
drivers/block/rbd.c:5090:19: warning: format not a string literal and no format arguments [-Wformat-security]
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Ilya Dryomov <ilya.dryomov@inktank.com>
Now that rbd_img_request_create() is called from work functions, no
need to use GFP_ATOMIC.
Signed-off-by: Ilya Dryomov <ilya.dryomov@inktank.com>
Reviewed-by: Alex Elder <elder@linaro.org>
While it was never a good idea to sleep in request_fn(), commit
34c6bc2c91 ("locking/mutexes: Add extra reschedule point") made it
a *bad* idea. mutex_lock() since 3.15 may reschedule *before* putting
task on the mutex wait queue, which for tasks in !TASK_RUNNING state
means block forever. request_fn() may be called with !TASK_RUNNING on
the way to schedule() in io_schedule().
Offload request handling to a workqueue, one per rbd device, to avoid
calling blocking primitives from rbd_request_fn().
Fixes: http://tracker.ceph.com/issues/8818
Cc: stable@vger.kernel.org # 3.16, needs backporting for 3.15
Signed-off-by: Ilya Dryomov <ilya.dryomov@inktank.com>
Tested-by: Eric Eastman <eric0e@aol.com>
Tested-by: Greg Wilson <greg.wilson@keepertech.com>
Reviewed-by: Alex Elder <elder@linaro.org>
If we are mapping a snapshot, we must read in the parent_overlap value
of that snapshot instead of that of the base image. Not doing so may
in particular result in us returning zeros instead of user data:
# cat overlap-snap.sh
#!/bin/bash
rbd create --size 10 --image-format 2 foo
FOO_DEV=$(rbd map foo)
dd if=/dev/urandom of=$FOO_DEV bs=1M &>/dev/null
echo "Base image"
dd if=$FOO_DEV bs=1 count=16 skip=$(((4 << 20) - 8)) 2>/dev/null | xxd
rbd snap create foo@snap
rbd snap protect foo@snap
rbd clone foo@snap bar
rbd snap create bar@snap
BAR_DEV=$(rbd map bar@snap)
echo "Snapshot"
dd if=$BAR_DEV bs=1 count=16 skip=$(((4 << 20) - 8)) 2>/dev/null | xxd
rbd resize --allow-shrink --size 4 bar
echo "Snapshot after base image resize"
dd if=$BAR_DEV bs=1 count=16 skip=$(((4 << 20) - 8)) 2>/dev/null | xxd
# ./overlap-snap.sh
Base image
0000000: e781 e33b d34b 2225 6034 2845 a2e3 36ed ...;.K"%`4(E..6.
Snapshot
0000000: e781 e33b d34b 2225 6034 2845 a2e3 36ed ...;.K"%`4(E..6.
Resizing image: 100% complete...done.
Snapshot after base image resize
0000000: e781 e33b d34b 2225 0000 0000 0000 0000 ...;.K"%........
Even though bar@snap is taken with the old bar parent_overlap (8M),
reads from bar@snap beyond the new bar parent_overlap (4M) return
zeroes. Fix it.
Signed-off-by: Ilya Dryomov <ilya.dryomov@inktank.com>
Reviewed-by: Alex Elder <elder@linaro.org>
Currently rbd_dev_v2_header_info() reads in parent info before the snap
context is read in. This is wrong, because we may need to look at the
the parent_overlap value of the snapshot instead of that of the base
image, for example when mapping a snapshot - see next commit. (When
mapping a snapshot, all we got is its name and we need the snap context
to translate that name into an id to know which parent info to look
for.)
The approach taken here is to make sure rbd_dev_v2_parent_info() is
called after the snap context has been read in. The other approach
would be to add a parent_overlap field to struct rbd_mapping and
maintain it the same way rbd_mapping::size is maintained. The reason
I chose the first approach is that the value of keeping around both
base image values and the actual mapping values is unclear to me.
Signed-off-by: Ilya Dryomov <ilya.dryomov@inktank.com>
Reviewed-by: Alex Elder <elder@linaro.org>
There is no sense in trying to update the mapping size before it's even
been set.
Signed-off-by: Ilya Dryomov <ilya.dryomov@inktank.com>
Reviewed-by: Alex Elder <elder@linaro.org>
Recently discovered watch/notify problems showed that we really can't
ignore errors in anything refresh related. Alas, currently there is
not much we can do in response to those errors, except print warnings.
Signed-off-by: Ilya Dryomov <ilya.dryomov@inktank.com>
Reviewed-by: Alex Elder <elder@linaro.org>
rbd_dev_spec_update() has two modes of operation, with nothing in
common between them. Split it into two functions, one for each mode
and make our expectations more clear.
Signed-off-by: Ilya Dryomov <ilya.dryomov@inktank.com>
Reviewed-by: Alex Elder <elder@linaro.org>
spec->image_id assert doesn't buy us much and image_format is asserted
in rbd_dev_header_name() and rbd_dev_header_info() anyway.
Signed-off-by: Ilya Dryomov <ilya.dryomov@inktank.com>
Reviewed-by: Alex Elder <elder@linaro.org>
A wrapper around rbd_dev_v{1,2}_header_info() to reduce duplication.
Signed-off-by: Ilya Dryomov <ilya.dryomov@inktank.com>
Reviewed-by: Alex Elder <elder@linaro.org>
Make /sys/bus/rbd/devices/<id>/parent show the entire chain of parent
images. While at it, kernel sprintf() doesn't return negative values,
casting to unsigned long long is no longer necessary and there is no
good reason to split into multiple sprintf() calls.
Signed-off-by: Ilya Dryomov <ilya.dryomov@inktank.com>
Reviewed-by: Alex Elder <elder@linaro.org>
Free memory allocated using kmem_cache_zalloc using kmem_cache_free
rather than kfree. The helper rbd_segment_name_free does the job here.
Its position is shifted above the calling function.
The Coccinelle semantic patch that detects this change is as follows:
// <smpl>
@@
expression x,E,c;
@@
x = \(kmem_cache_alloc\|kmem_cache_zalloc\|kmem_cache_alloc_node\)(c,...)
... when != x = E
when != &x
?-kfree(x)
+kmem_cache_free(c,x)
// </smpl>
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Ilya Dryomov <ilya.dryomov@inktank.com>
image_id is leaked if the parent happens to have been recorded already.
Fix it.
Signed-off-by: Ilya Dryomov <ilya.dryomov@inktank.com>
Reviewed-by: Alex Elder <elder@linaro.org>
Switch rbd_dev_header_{un,}watch_sync() to use the new helper and fix
rbd_dev_header_unwatch_sync() to destroy watch_request structures
before queuing watch-remove message while at it. This mistake slipped
into commit b30a01f2a3 ("rbd: fix osd_request memory leak in
__rbd_dev_header_watch_sync()") and could lead to "image still in use"
errors on image removal.
Signed-off-by: Ilya Dryomov <ilya.dryomov@inktank.com>
Reviewed-by: Alex Elder <elder@linaro.org>
In the past, rbd_dev_header_watch_sync() used to handle both watch and
unwatch requests and was entangled and leaky. Commit b30a01f2a3
("rbd: fix osd_request memory leak in __rbd_dev_header_watch_sync()")
split it into two separate functions. This commit cleanly abstracts
the common bits, relying on the fixed rbd_obj_request_wait().
Signed-off-by: Ilya Dryomov <ilya.dryomov@inktank.com>
Reviewed-by: Alex Elder <elder@linaro.org>
rbd_obj_request_wait() should cancel the underlying OSD request if
interrupted. Otherwise libceph will hold onto it indefinitely, causing
assert failures or leaking the original object request.
This also adds an rbd wrapper around ceph_osdc_cancel_request() to
match rbd_obj_request_submit() and rbd_obj_request_wait().
Signed-off-by: Ilya Dryomov <ilya.dryomov@inktank.com>
Reviewed-by: Alex Elder <elder@linaro.org>
The following check in rbd_img_obj_request_submit()
rbd_dev->parent_overlap <= obj_request->img_offset
allows the fall through to the non-layered write case even if both
parent_overlap and obj_request->img_offset belong to the same RADOS
object. This leads to data corruption, because the area to the left of
parent_overlap ends up unconditionally zero-filled instead of being
populated with parent data. Suppose we want to write 1M to offset 6M
of image bar, which is a clone of foo@snap; object_size is 4M,
parent_overlap is 5M:
rbd_data.<id>.0000000000000001
---------------------|----------------------|------------
| should be copyup'ed | should be zeroed out | write ...
---------------------|----------------------|------------
4M 5M 6M
parent_overlap obj_request->img_offset
4..5M should be copyup'ed from foo, yet it is zero-filled, just like
5..6M is.
Given that the only striping mode kernel client currently supports is
chunking (i.e. stripe_unit == object_size, stripe_count == 1), round
parent_overlap up to the next object boundary for the purposes of the
overlap check.
Cc: stable@vger.kernel.org # 3.10+
Signed-off-by: Ilya Dryomov <ilya.dryomov@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
rbd_open(), called every time the device is opened, calls
set_device_ro(). There's no reason to set the device read-only or
read-write every time it is opened. Just do this once during device
setup, using set_disk_ro() instead because the struct block_device
isn't available to us there.
Signed-off-by: Josh Durgin <josh.durgin@inktank.com>
Reviewed-by: Alex Elder <elder@linaro.org>
get_user() and set_disk_ro() may allocate memory, leading to a
potential deadlock if theye are called while a spin lock is held.
Move the acquisition and release of rbd_dev->lock from rbd_ioctl()
into rbd_ioctl_set_ro(), so it can occur between get_user() and
set_disk_ro().
Signed-off-by: Josh Durgin <josh.durgin@inktank.com>
Reviewed-by: Alex Elder <elder@linaro.org>
When running the following commands:
[root@ceph0 mnt]# blockdev --setro /dev/rbd1
[root@ceph0 mnt]# blockdev --getro /dev/rbd1
0
The block setro didn't take effect, it is because
the rbd doesn't support ioctl of block driver.
This resolves:
http://tracker.ceph.com/issues/6265
Signed-off-by: Guangliang Zhao <guangliang@unitedstack.com>
Reviewed-by: Alex Elder <elder@linaro.org>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
ida_destroy() needs to be called on module exit to release ida caches.
Signed-off-by: Ilya Dryomov <ilya.dryomov@inktank.com>
Reviewed-by: Alex Elder <elder@linaro.org>
Each image request contains a reference count, but to date it has
not actually been used. (I think this was just an oversight.) A
recent report involving rbd failing an assertion shed light on why
and where we need to use these reference counts.
Every OSD request associated with an object request uses
rbd_osd_req_callback() as its callback function. That function will
call a helper function (dependent on the type of OSD request) that
will set the object request's "done" flag if the object request if
appropriate. If that "done" flag is set, the object request is
passed to rbd_obj_request_complete().
In rbd_obj_request_complete(), requests are processed in sequential
order. So if an object request completes before one of its
predecessors in the image request, the completion is deferred.
Otherwise, if it's a completing object's "turn" to be completed, it
is passed to rbd_img_obj_end_request(), which records the result of
the operation, accumulates transferred bytes, and so on. Next, the
successor to this request is checked and if it is marked "done",
(deferred) completion processing is performed on that request, and
so on. If the last object request in an image request is completed,
rbd_img_request_complete() is called, which (typically) destroys
the image request.
There is a race here, however. The instant an object request is
marked "done" it can be provided (by a thread handling completion of
one of its predecessor operations) to rbd_img_obj_end_request(),
which (for the last request) can then lead to the image request
getting torn down. And this can happen *before* that object has
itself entered rbd_img_obj_end_request(). As a result, once it
*does* enter that function, the image request (and even the object
request itself) may have been freed and become invalid.
All that's necessary to avoid this is to properly count references
to the image requests. We tear down an image request's object
requests all at once--only when the entire image request has
completed. So there's no need for an image request to count
references for its object requests. However, we don't want an
image request to go away until the last of its object requests
has passed through rbd_img_obj_callback(). In other words,
we don't want rbd_img_request_complete() to necessarily
result in the image request being destroyed, because it may
get called before we've finished processing on all of its
object requests.
So the fix is to add a reference to an image request for
each of its object requests. The reference can be viewed
as representing an object request that has not yet finished
its call to rbd_img_obj_callback(). That is emphasized by
getting the reference right after assigning that as the image
object's callback function. The corresponding release of that
reference is done at the end of rbd_img_obj_callback(), which
every image object request passes through exactly once.
Cc: stable@vger.kernel.org
Signed-off-by: Alex Elder <elder@linaro.org>
Reviewed-by: Ilya Dryomov <ilya.dryomov@inktank.com>
osd_request, along with r_request and r_reply messages attached to it
are leaked in __rbd_dev_header_watch_sync() if the requested image
doesn't exist. This is because lingering requests are special and get
an extra ref in the reply path. Fix it by unregistering linger request
on the error path and split __rbd_dev_header_watch_sync() into two
functions to make it maintainable.
Signed-off-by: Ilya Dryomov <ilya.dryomov@inktank.com>
Given an existing idle mapping (img1), mapping an image (img2) in
a newly created pool (pool2) fails:
$ ceph osd pool create pool1 8 8
$ rbd create --size 1000 pool1/img1
$ sudo rbd map pool1/img1
$ ceph osd pool create pool2 8 8
$ rbd create --size 1000 pool2/img2
$ sudo rbd map pool2/img2
rbd: sysfs write failed
rbd: map failed: (2) No such file or directory
This is because client instances are shared by default and we don't
request an osdmap update when bumping a ref on an existing client. The
fix is to use the mon_get_version request to see if the osdmap we have
is the latest, and block until the requested update is received if it's
not.
Fixes: http://tracker.ceph.com/issues/8184
Signed-off-by: Ilya Dryomov <ilya.dryomov@inktank.com>
Reviewed-by: Sage Weil <sage@inktank.com>
In an effort to reduce fragmentation, prefix every rbd write with
a CEPH_OSD_OP_SETALLOCHINT osd op with an expected_write_size value set
to the object size (1 << order). Backwards compatibility is taken care
of on the libceph/osd side.
"The CEPH_OSD_OP_SETALLOCHINT hint is durable, in that it's enough to
do it once. The reason every rbd write is prefixed is that rbd doesn't
explicitly create objects and relies on writes creating them
implicitly, so there is no place to stick a single hint op into. To
get around that we decided to prefix every rbd write with a hint (just
like write and setattr ops, hint op will create an object implicitly if
it doesn't exist)."
Signed-off-by: Ilya Dryomov <ilya.dryomov@inktank.com>
Reviewed-by: Sage Weil <sage@inktank.com>
Reviewed-by: Alex Elder <elder@linaro.org>
In preparation for prefixing rbd writes with an allocation hint
introduce a num_ops parameter for rbd_osd_req_create(). The rationale
is that not every write request is a write op that needs to be prefixed
(e.g. watch op), so the num_ops logic needs to be in the callers.
Signed-off-by: Ilya Dryomov <ilya.dryomov@inktank.com>
Reviewed-by: Sage Weil <sage@inktank.com>
Reviewed-by: Alex Elder <elder@linaro.org>
Our longest osd request now contains 3 ops: copyup+hint+write.
Also, CEPH_OSD_MAX_OP value in a BUG_ON in rbd_osd_req_callback() was
hard-coded to 2. Fix it, and switch to rbd_assert while at it.
Signed-off-by: Ilya Dryomov <ilya.dryomov@inktank.com>
Reviewed-by: Sage Weil <sage@inktank.com>
Reviewed-by: Alex Elder <elder@linaro.org>
Doing rbd_obj_request_put() in rbd_img_request_fill() error paths is
not only insufficient, but also triggers an rbd_assert() in
rbd_obj_request_destroy():
Assertion failure in rbd_obj_request_destroy() at line 1867:
rbd_assert(obj_request->img_request == NULL);
rbd_img_obj_request_add() adds obj_requests to the img_request, the
opposite is rbd_img_obj_request_del(). Use it.
Fixes: http://tracker.ceph.com/issues/7327
Signed-off-by: Ilya Dryomov <ilya.dryomov@inktank.com>
Reviewed-by: Alex Elder <elder@linaro.org>
Commit 03507db631 ("rbd: fix buffer size for writes to images with
snapshots") moved the call to rbd_img_obj_request_add() up, making the
out_partial label bogus. Remove it.
Signed-off-by: Ilya Dryomov <ilya.dryomov@inktank.com>
Reviewed-by: Alex Elder <elder@linaro.org>
Olivier Bonvalet reported having repeated crashes due to a failed
assertion he was hitting in rbd_img_obj_callback():
Assertion failure in rbd_img_obj_callback() at line 2165:
rbd_assert(which >= img_request->next_completion);
With a lot of help from Olivier with reproducing the problem
we were able to determine the object and image requests had
already been completed (and often freed) at the point the
assertion failed.
There was a great deal of discussion on the ceph-devel mailing list
about this. The problem only arose when there were two (or more)
object requests in an image request, and the problem was always
seen when the second request was being completed.
The problem is due to a race in the window between setting the
"done" flag on an object request and checking the image request's
next completion value. When the first object request completes, it
checks to see if its successor request is marked "done", and if
so, that request is also completed. In the process, the image
request's next_completion value is updated to reflect that both
the first and second requests are completed. By the time the
second request is able to check the next_completion value, it
has been set to a value *greater* than its own "which" value,
which caused an assertion to fail.
Fix this problem by skipping over any completion processing
unless the completing object request is the next one expected.
Test only for inequality (not >=), and eliminate the bad
assertion.
Tested-by: Olivier Bonvalet <ob@daevel.fr>
Signed-off-by: Alex Elder <elder@linaro.org>
Reviewed-by: Sage Weil <sage@inktank.com>
Reviewed-by: Ilya Dryomov <ilya.dryomov@inktank.com>
Pull core block IO changes from Jens Axboe:
"The major piece in here is the immutable bio_ve series from Kent, the
rest is fairly minor. It was supposed to go in last round, but
various issues pushed it to this release instead. The pull request
contains:
- Various smaller blk-mq fixes from different folks. Nothing major
here, just minor fixes and cleanups.
- Fix for a memory leak in the error path in the block ioctl code
from Christian Engelmayer.
- Header export fix from CaiZhiyong.
- Finally the immutable biovec changes from Kent Overstreet. This
enables some nice future work on making arbitrarily sized bios
possible, and splitting more efficient. Related fixes to immutable
bio_vecs:
- dm-cache immutable fixup from Mike Snitzer.
- btrfs immutable fixup from Muthu Kumar.
- bio-integrity fix from Nic Bellinger, which is also going to stable"
* 'for-3.14/core' of git://git.kernel.dk/linux-block: (44 commits)
xtensa: fixup simdisk driver to work with immutable bio_vecs
block/blk-mq-cpu.c: use hotcpu_notifier()
blk-mq: for_each_* macro correctness
block: Fix memory leak in rw_copy_check_uvector() handling
bio-integrity: Fix bio_integrity_verify segment start bug
block: remove unrelated header files and export symbol
blk-mq: uses page->list incorrectly
blk-mq: use __smp_call_function_single directly
btrfs: fix missing increment of bi_remaining
Revert "block: Warn and free bio if bi_end_io is not set"
block: Warn and free bio if bi_end_io is not set
blk-mq: fix initializing request's start time
block: blk-mq: don't export blk_mq_free_queue()
block: blk-mq: make blk_sync_queue support mq
block: blk-mq: support draining mq queue
dm cache: increment bi_remaining when bi_end_io is restored
block: fixup for generic bio chaining
block: Really silence spurious compiler warnings
block: Silence spurious compiler warnings
block: Kill bio_pair_split()
...
Rename ceph_osd_request::r_{oloc,oid} to r_base_{oloc,oid} before
introducing r_target_{oloc,oid} needed for redirects.
Signed-off-by: Ilya Dryomov <ilya.dryomov@inktank.com>
Reviewed-by: Sage Weil <sage@inktank.com>
In preparation for tiering support, which would require having two
(base and target) object names for each osd request and also copying
those names around, introduce struct ceph_object_id (oid) and a couple
helpers to facilitate those copies and encapsulate the fact that object
name is not necessarily a NUL-terminated string.
Signed-off-by: Ilya Dryomov <ilya.dryomov@inktank.com>
Reviewed-by: Sage Weil <sage@inktank.com>
In preparation for adding oid abstraction, rename MAX_OBJ_NAME_SIZE to
CEPH_MAX_OID_NAME_LEN.
Signed-off-by: Ilya Dryomov <ilya.dryomov@inktank.com>
Reviewed-by: Sage Weil <sage@inktank.com>
Instead of relying on pool fields in ceph_file_layout (for mapping) and
ceph_pg (for enconding), start using ceph_object_locator (oloc)
abstraction. Note that userspace oloc currently consists of pool, key,
nspace and hash fields, while this one contains only a pool. This is
OK, because at this point we only send (i.e. encode) olocs and never
have to receive (i.e. decode) them.
This makes keeping a copy of ceph_file_layout in every osd request
unnecessary, so ceph_osd_request::r_file_layout field is nuked.
Signed-off-by: Ilya Dryomov <ilya.dryomov@inktank.com>
Reviewed-by: Sage Weil <sage@inktank.com>
Rename rbd_dev_header_watch_sync() to __rbd_dev_header_watch_sync() and
introduce two helpers: rbd_dev_header_{,un}watch_sync() to make it more
clear what is going on.
Signed-off-by: Ilya Dryomov <ilya.dryomov@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
Currently each rbd device is allocated its own major number, which
leads to a hard limit of 230-250 images mapped at once. This commit
adds support for a new single-major device number allocation scheme,
which is hidden behind a new single_major boolean module parameter and
is disabled by default for backwards compatibility reasons. (Old
userspace cannot correctly unmap images mapped under single-major
scheme and would essentially just unmap a random image, if that.)
$ rbd showmapped
id pool image snap device
0 rbd b100 - /dev/rbd0
1 rbd b101 - /dev/rbd1
2 rbd b102 - /dev/rbd2
3 rbd b103 - /dev/rbd3
Old scheme (modprobe rbd):
$ ls -l /dev/rbd*
brw-rw---- 1 root disk 253, 0 Dec 10 12:24 /dev/rbd0
brw-rw---- 1 root disk 252, 0 Dec 10 12:28 /dev/rbd1
brw-rw---- 1 root disk 252, 1 Dec 10 12:28 /dev/rbd1p1
brw-rw---- 1 root disk 252, 2 Dec 10 12:28 /dev/rbd1p2
brw-rw---- 1 root disk 252, 3 Dec 10 12:28 /dev/rbd1p3
brw-rw---- 1 root disk 251, 0 Dec 10 12:28 /dev/rbd2
brw-rw---- 1 root disk 251, 1 Dec 10 12:28 /dev/rbd2p1
brw-rw---- 1 root disk 250, 0 Dec 10 12:24 /dev/rbd3
New scheme (modprobe rbd single_major=Y):
$ ls -l /dev/rbd*
brw-rw---- 1 root disk 253, 0 Dec 10 12:30 /dev/rbd0
brw-rw---- 1 root disk 253, 256 Dec 10 12:30 /dev/rbd1
brw-rw---- 1 root disk 253, 257 Dec 10 12:30 /dev/rbd1p1
brw-rw---- 1 root disk 253, 258 Dec 10 12:30 /dev/rbd1p2
brw-rw---- 1 root disk 253, 259 Dec 10 12:30 /dev/rbd1p3
brw-rw---- 1 root disk 253, 512 Dec 10 12:30 /dev/rbd2
brw-rw---- 1 root disk 253, 513 Dec 10 12:30 /dev/rbd2p1
brw-rw---- 1 root disk 253, 768 Dec 10 12:30 /dev/rbd3
(major 253 was assigned dynamically at module load time)
The new limit is 4096 images mapped at once, and it comes from the fact
that, as before, 256 minor numbers are reserved for each mapping.
(A follow-up commit changes the number of minors reserved and the way
we deal with partitions over that number.)
If single_major is set to true, two new sysfs interfaces show up:
/sys/bus/rbd/{add,remove}_single_major. These are to be used instead
of /sys/bus/rbd/{add,remove}, which are disabled for backwards
compatibility reasons outlined above.
Signed-off-by: Ilya Dryomov <ilya.dryomov@inktank.com>
Reviewed-by: Alex Elder <elder@linaro.org>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
In preparation for single-major device number allocation scheme, wire
up attribute_group::is_visible() callback for rbd bus. This allows us
to make the new single-major attributes conditional.
Signed-off-by: Ilya Dryomov <ilya.dryomov@inktank.com>
Reviewed-by: Alex Elder <elder@linaro.org>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
Introduce /sys/bus/rbd/devices/<id>/minor sysfs attribute for exporting
rbd whole disk minor numbers. This is a step towards single-major
device number allocation scheme, but also a good thing on its own.
Signed-off-by: Ilya Dryomov <ilya.dryomov@inktank.com>
Reviewed-by: Alex Elder <elder@linaro.org>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
Currently rbd ids are allocated using an atomic variable that keeps
track of the highest id currently in use and each new id is simply one
more than the value of that variable. That's nice and cheap, but it
does mean that rbd ids are allowed to grow boundlessly, and, more
importantly, it's completely unpredictable. So, in preparation for
single-major device number allocation scheme, which is going to
establish and rely on a constant mapping between rbd ids and device
numbers, switch to ida for rbd id assignments.
Signed-off-by: Ilya Dryomov <ilya.dryomov@inktank.com>
Reviewed-by: Alex Elder <elder@linaro.org>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
Refactor rbd_init() a bit to make it more clear what's going on.
Signed-off-by: Ilya Dryomov <ilya.dryomov@inktank.com>
Reviewed-by: Alex Elder <elder@linaro.org>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
Tweak "loaded" message, so that it looks like
[ 30.184235] rbd: loaded
instead of
[ 38.056564] rbd: loaded rbd (rados block device)
Also move (and slightly tweak) MODULE_DESCRIPTION so that all authors
are next to each other in modinfo output.
Signed-off-by: Ilya Dryomov <ilya.dryomov@inktank.com>
Reviewed-by: Alex Elder <elder@linaro.org>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
rbd_device::dev_id is an int, format it as such.
Signed-off-by: Ilya Dryomov <ilya.dryomov@inktank.com>
Reviewed-by: Alex Elder <elder@linaro.org>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
Now that we've got drivers converted to the new immutable bvec
primitives, bio splitting becomes much easier - this is how the new
bio_split() will work. (Someone more familiar with the ceph code could
probably use bio_clone_fast() instead of bio_clone() here).
Signed-off-by: Kent Overstreet <kmo@daterainc.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Yehuda Sadeh <yehuda@inktank.com>
Cc: Alex Elder <elder@inktank.com>
Cc: ceph-devel@vger.kernel.org
More prep work for immutable biovecs - with immutable bvecs drivers
won't be able to use the biovec directly, they'll need to use helpers
that take into account bio->bi_iter.bi_bvec_done.
This updates callers for the new usage without changing the
implementation yet.
Signed-off-by: Kent Overstreet <kmo@daterainc.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: "Ed L. Cashin" <ecashin@coraid.com>
Cc: Nick Piggin <npiggin@kernel.dk>
Cc: Lars Ellenberg <drbd-dev@lists.linbit.com>
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Paul Clements <Paul.Clements@steeleye.com>
Cc: Jim Paris <jim@jtan.com>
Cc: Geoff Levand <geoff@infradead.org>
Cc: Yehuda Sadeh <yehuda@inktank.com>
Cc: Sage Weil <sage@inktank.com>
Cc: Alex Elder <elder@inktank.com>
Cc: ceph-devel@vger.kernel.org
Cc: Joshua Morris <josh.h.morris@us.ibm.com>
Cc: Philip Kelleher <pjk1939@linux.vnet.ibm.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Cc: Neil Brown <neilb@suse.de>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: linux390@de.ibm.com
Cc: Nagalakshmi Nandigama <Nagalakshmi.Nandigama@lsi.com>
Cc: Sreekanth Reddy <Sreekanth.Reddy@lsi.com>
Cc: support@lsi.com
Cc: "James E.J. Bottomley" <JBottomley@parallels.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: Steven Whitehouse <swhiteho@redhat.com>
Cc: Herton Ronaldo Krzesinski <herton.krzesinski@canonical.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Guo Chao <yan@linux.vnet.ibm.com>
Cc: Asai Thambi S P <asamymuthupa@micron.com>
Cc: Selvan Mani <smani@micron.com>
Cc: Sam Bradshaw <sbradshaw@micron.com>
Cc: Matthew Wilcox <matthew.r.wilcox@intel.com>
Cc: Keith Busch <keith.busch@intel.com>
Cc: Stephen Hemminger <shemminger@vyatta.com>
Cc: Quoc-Son Anh <quoc-sonx.anh@intel.com>
Cc: Sebastian Ott <sebott@linux.vnet.ibm.com>
Cc: Nitin Gupta <ngupta@vflare.org>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Jerome Marchand <jmarchan@redhat.com>
Cc: Seth Jennings <sjenning@linux.vnet.ibm.com>
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>
Cc: Mike Snitzer <snitzer@redhat.com>
Cc: Vivek Goyal <vgoyal@redhat.com>
Cc: "Darrick J. Wong" <darrick.wong@oracle.com>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Cc: Jan Kara <jack@suse.cz>
Cc: linux-m68k@lists.linux-m68k.org
Cc: linuxppc-dev@lists.ozlabs.org
Cc: drbd-user@lists.linbit.com
Cc: nbd-general@lists.sourceforge.net
Cc: cbe-oss-dev@lists.ozlabs.org
Cc: xen-devel@lists.xensource.com
Cc: virtualization@lists.linux-foundation.org
Cc: linux-raid@vger.kernel.org
Cc: linux-s390@vger.kernel.org
Cc: DL-MPTFusionLinux@lsi.com
Cc: linux-scsi@vger.kernel.org
Cc: devel@driverdev.osuosl.org
Cc: linux-fsdevel@vger.kernel.org
Cc: cluster-devel@redhat.com
Cc: linux-mm@kvack.org
Acked-by: Geoff Levand <geoff@infradead.org>
Pull ceph fixes from Sage Weil:
"These fix several bugs with RBD from 3.11 that didn't get tested in
time for the merge window: some error handling, a use-after-free, and
a sequencing issue when unmapping and image races with a notify
operation.
There is also a patch fixing a problem with the new ceph + fscache
code that just went in"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client:
fscache: check consistency does not decrement refcount
rbd: fix error handling from rbd_snap_name()
rbd: ignore unmapped snapshots that no longer exist
rbd: fix use-after free of rbd_dev->disk
rbd: make rbd_obj_notify_ack() synchronous
rbd: complete notifies before cleaning up osd_client and rbd_dev
libceph: add function to ensure notifies are complete
The use of strict_strtoul() is not preferred, because strict_strtoul() is
obsolete. Thus, kstrtoul() should be used.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
rbd_snap_name() calls rbd_dev_v{1,2}_snap_name() depending on the
format of the image. The format 1 version returns NULL on error, which
is handled by the caller. The format 2 version returns an ERR_PTR,
which the caller of rbd_snap_name() does not expect.
Fortunately this is unlikely to occur in practice because
rbd_snap_id_by_name() is called before rbd_snap_name(). This would hit
similar errors to rbd_snap_name() (like the snapshot not existing) and
return early, so rbd_snap_name() would not hit an error unless the
snapshot was removed between the two calls or memory was exhausted.
Use an ERR_PTR in rbd_dev_v1_snap_name() so that the specific error
can be propagated, and it is consistent with rbd_dev_v2_snap_name().
Handle the ERR_PTR in the only rbd_snap_name() caller.
Suggested-by: Alex Elder <alex.elder@linaro.org>
Signed-off-by: Josh Durgin <josh.durgin@inktank.com>
Reviewed-by: Alex Elder <elder@linaro.org>
This prevents erroring out while adding a device when a snapshot
unrelated to the current mapping is deleted between reading the
snapshot context and reading the snapshot names. If the mapped
snapshot name is not found an error still occurs as usual.
Signed-off-by: Josh Durgin <josh.durgin@inktank.com>
Reviewed-by: Alex Elder <elder@linaro.org>
Removing a device deallocates the disk, unschedules the watch, and
finally cleans up the rbd_dev structure. rbd_dev_refresh(), called
from the watch callback, updates the disk size and rbd_dev
structure. With no locking between them, rbd_dev_refresh() may use the
device or rbd_dev after they've been freed.
To fix this, check whether RBD_DEV_FLAG_REMOVING is set before
updating the disk size in rbd_dev_refresh(). In order to prevent a
race where rbd_dev_refresh() is already revalidating the disk when
rbd_remove() is called, move the call to rbd_bus_del_dev() after the
watch is unregistered and all notifies are complete. It's safe to
defer deleting this structure because no new requests can be submitted
once the RBD_DEV_FLAG_REMOVING is set, since the device cannot be
opened.
Fixes: http://tracker.ceph.com/issues/5636
Signed-off-by: Josh Durgin <josh.durgin@inktank.com>
Reviewed-by: Alex Elder <elder@linaro.org>
The only user of rbd_obj_notify_ack() is rbd_watch_cb(). It used
asynchronously with no tracking of when the notify ack completes, so
it may still be in progress when the osd_client is shut down. This
results in a BUG() since the osd client assumes no requests are in
flight when it stops. Since all notifies are flushed before the
osd_client is stopped, waiting for the notify ack to complete before
returning from the watch callback ensures there are no notify acks in
flight during shutdown.
Rename rbd_obj_notify_ack() to rbd_obj_notify_ack_sync() to reflect
its new synchronous nature.
Signed-off-by: Josh Durgin <josh.durgin@inktank.com>
Reviewed-by: Alex Elder <elder@linaro.org>
To ensure rbd_dev is not used after it's released, flush all pending
notify callbacks before calling rbd_dev_image_release(). No new
notifies can be added to the queue at this point because the watch has
already be unregistered with the osd_client.
Signed-off-by: Josh Durgin <josh.durgin@inktank.com>
Reviewed-by: Alex Elder <elder@linaro.org>
Pull ceph updates from Sage Weil:
"This includes both the first pile of Ceph patches (which I sent to
torvalds@vger, sigh) and a few new patches that add support for
fscache for Ceph. That includes a few fscache core fixes that David
Howells asked go through the Ceph tree. (Thanks go to Milosz Tanski
for putting this feature together)
This first batch of patches (included here) had (has) several
important RBD bug fixes, hole punch support, several different
cleanups in the page cache interactions, improvements in the truncate
code (new truncate mutex to avoid shenanigans with i_mutex), and a
series of fixes in the synchronous striping read/write code.
On top of that is a random collection of small fixes all across the
tree (error code checks and error path cleanup, obsolete wq flags,
etc)"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client: (43 commits)
ceph: use d_invalidate() to invalidate aliases
ceph: remove ceph_lookup_inode()
ceph: trivial buildbot warnings fix
ceph: Do not do invalidate if the filesystem is mounted nofsc
ceph: page still marked private_2
ceph: ceph_readpage_to_fscache didn't check if marked
ceph: clean PgPrivate2 on returning from readpages
ceph: use fscache as a local presisent cache
fscache: Netfs function for cleanup post readpages
FS-Cache: Fix heading in documentation
CacheFiles: Implement interface to check cache consistency
FS-Cache: Add interface to check consistency of a cached object
rbd: fix null dereference in dout
rbd: fix buffer size for writes to images with snapshots
libceph: use pg_num_mask instead of pgp_num_mask for pg.seed calc
rbd: fix I/O error propagation for reads
ceph: use vfs __set_page_dirty_nobuffers interface instead of doing it inside filesystem
ceph: allow sync_read/write return partial successed size of read/write.
ceph: fix bugs about handling short-read for sync read mode.
ceph: remove useless variable revoked_rdcache
...
The order parameter is sometimes NULL in _rbd_dev_v2_snap_size(), but
the dout() always derefences it. Move this to another dout() protected
by a check that order is non-NULL.
Signed-off-by: Josh Durgin <josh.durgin@inktank.com>
Reviewed-by: Sage Weil <sage@inktank.com>
Reviewed-by: Alex Elder <alex.elder@linaro.org>
rbd_osd_req_create() needs to know the snapshot context size to create
a buffer large enough to send it with the message front. It gets this
from the img_request, which was not set for the obj_request yet. This
resulted in trying to write past the end of the front payload, hitting
this BUG:
libceph: BUG_ON(p > msg->front.iov_base + msg->front.iov_len);
Fix this by associating the obj_request with its img_request
immediately after it's created, before the osd request is created.
Fixes: http://tracker.ceph.com/issues/5760
Suggested-by: Alex Elder <alex.elder@linaro.org>
Signed-off-by: Josh Durgin <josh.durgin@inktank.com>
Reviewed-by: Alex Elder <alex.elder@linaro.org>
When a request returns an error, the driver needs to report the entire
extent of the request as completed. Writes already did this, since
they always set xferred = length, but reads were skipping that step if
an error other than -ENOENT occurred. Instead, rbd would end up
passing 0 xferred to blk_end_request(), which would always report
needing more data. This resulted in an assert failing when more data
was required by the block layer, but all the object requests were
done:
[ 1868.719077] rbd: obj_request read result -108 xferred 0
[ 1868.719077]
[ 1868.719518] end_request: I/O error, dev rbd1, sector 0
[ 1868.719739]
[ 1868.719739] Assertion failure in rbd_img_obj_callback() at line 1736:
[ 1868.719739]
[ 1868.719739] rbd_assert(more ^ (which == img_request->obj_request_count));
Without this assert, reads that hit errors would hang forever, since
the block layer considered them incomplete.
Fixes: http://tracker.ceph.com/issues/5647
CC: stable@vger.kernel.org # v3.10
Signed-off-by: Josh Durgin <josh.durgin@inktank.com>
Reviewed-by: Alex Elder <alex.elder@linaro.org>
The bus_attrs field of struct bus_type is going away soon, dev_groups
should be used instead. This converts the RBD bus code to use the
correct field.
Cc: Yehuda Sadeh <yehuda@inktank.com>
Cc: Sage Weil <sage@inktank.com>
Acked-by: Alex Elder <elder@linaro.org>
Cc: <ceph-devel@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The local variables such as 'bio_list', and 'pages' are pointers;
thus, use NULL instead of 0 to fix the following sparse warnings.
drivers/block/rbd.c:2166:32: warning: Using plain integer as NULL pointer
drivers/block/rbd.c:2168:31: warning: Using plain integer as NULL pointer
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Reviewed-by: Sage Weil <sage@inktank.com>
gcc isn't quite smart enough and generates these warnings:
drivers/block/rbd.c: In function 'rbd_img_request_fill':
drivers/block/rbd.c:1266:22: warning: 'bio_list' may be used uninitialized in this function [-Wmaybe-uninitialized]
drivers/block/rbd.c:2186:14: note: 'bio_list' was declared here
drivers/block/rbd.c:2247:10: warning: 'pages' may be used uninitialized in this function [-Wmaybe-uninitialized]
even though they are initialized for their respective code paths.
Signed-off-by: Sage Weil <sage@inktank.com>
Updating an image header needs to be protected to ensure it's
done consistently. However distinct headers can be updated
concurrently without a problem. Instead of using the global
control lock to serialize headder updates, just rely on the header
semaphore. (It's already used, this just moves it out to cover
a broader section of the code.)
That leaves the control mutex protecting only the creation of rbd
clients, so rename it.
This resolves:
http://tracker.ceph.com/issues/5222
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
When an rbd device is first getting mapped, its device registration
is protected the control mutex. There is no need to do that though,
because the device has already been assigned an id that's guaranteed
to be unique.
An unmap of an rbd device won't proceed if the device has a non-zero
open count or is already being unmapped. So there's no need to hold
the control mutex in that case either.
Finally, an rbd device can't be opened if it is being removed, and
it won't go away if there is a non-zero open count. So here too
there's no need to hold the control mutex while getting or putting a
reference to an rbd device's Linux device structure.
Drop the mutex calls in these cases.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
Make sure two concurrent unmap operations on the same rbd device
won't collide, by only proceeding with the removal and cleanup of a
device if is not already underway.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
When unmapping a device, its id is supplied, and that is used to
look up which rbd device should be unmapped. Looking up the
device involves searching the rbd device list while holding
a spinlock that protects access to that list.
Currently all of this is done under protection of the control lock,
but that protection is going away soon. To ensure the rbd_dev is
still valid (still on the list) while setting its REMOVING flag, do
so while still holding the list lock. To do so, get rid of
__rbd_get_dev(), and open code what it did in the one place it
was used.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
If more than one rbd image has the same ceph cluster configuration
(same options, same set of monitors, same keys) they normally share
a single rbd client.
When an image is getting mapped, rbd looks to see if an existing
client can be used, and creates a new one if not.
The lookup and creation are not done under a common lock though, so
mapping two images concurrently could lead to duplicate clients
getting set up needlessly. This isn't a major problem, but it's
wasteful and different from what's intended.
This patch fixes that by using the control mutex to protect
both the lookup and (if needed) creation of the client. It
was previously used just when creating.
This resolves:
http://tracker.ceph.com/issues/3094
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
This includes a few relatively small fixes I found while examining
the code that refreshes image information.
This resolves:
http://tracker.ceph.com/issues/5040
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
Neither zero_bio_chain() nor zero_pages() contains a call to flush
caches after zeroing a portion of a page. This can cause problems
on architectures that have caches that allow virtual address
aliasing.
This resolves:
http://tracker.ceph.com/issues/4777
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
The reference to the original request dropped at the end of
rbd_img_obj_exists_callback() corresponds to the reference taken
in rbd_img_obj_exists_submit() to account for the stat request
referring to it. Move the put of that reference up right after
clearing that pointer to make its purpose more obvious.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
drivers/block/rbd.c: In function ‘zero_pages’:
drivers/block/rbd.c:1102: warning: comparison of distinct pointer types lacks a cast
Remove the hackish casts and use min_t() to fix this.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Reviewed-by: Alex Elder <elder@inktank.com>
Pull Ceph fix from Sage Weil:
"This is a recently spotted regression in the snapshot behavior...
It turns out several tests weren't being run in the nightlies so this
took a while to spot"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client:
rbd: send snapshot context with writes
Sending the right snapshot context with each write is required for
snapshots to work. Due to the ordering of calls, the snapshot context
is never set for any requests. This causes writes to the current
version of the image to be reflected in all snapshots, which are
supposed to be read-only.
This happens because rbd_osd_req_format_write() sets the snapshot
context based on obj_request->img_request. At this point, however,
obj_request->img_request has not been set yet, to the snapshot context
is set to NULL. Fix this by moving rbd_img_obj_request_add(), which
sets obj_request->img_request, before the osd request formatting
calls.
This resolves:
http://tracker.ceph.com/issues/5465
Reported-by: Karol Jurak <karol.jurak@gmail.com>
Signed-off-by: Josh Durgin <josh.durgin@inktank.com>
Reviewed-by: Sage Weil <sage@inktank.com>
Reviewed-by: Alex Elder <elder@linaro.org>
Pull Ceph fix from Sage Weil:
"This fixes another problem with using v2 images on 3.10 due to the
order in which fields are read from the image header.
Hopefully this is the last one"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client:
rbd: fetch object order before using it
rbd_dev_v2_header_onetime() fetches striping information, and
checks whether the image can be read by compariing the stripe unit
to the object size. It determines the object size by shifting
the object order, which is 0 at this point since it has not been
read yet. Move the call to get the image size and object order
before rbd_dev_v2_header_onetime() so it is set before use.
Signed-off-by: Josh Durgin <josh.durgin@inktank.com>
Reviewed-by: Sage Weil <sage@inktank.com>
Pull Ceph fix from Sage Weil:
"This fixes a problem preventing the kernel and userland librbd
libraries from sharing data with the new format 2 images"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client:
rbd: use the correct length for format 2 object names
Format 2 objects use 16 characters for the object name suffix to be
able to express the full 64-bit range of object numbers. Format 1
images only use 12 characters for this. Using 12-character names for
format 2 caused userspace and kernel rbd clients to read differently
named objects, which made an image written by one client look empty to
the other client.
CC: stable@vger.kernel.org # 3.9+
Reported-by: Chris Dunlop <chris@onthe.net.au>
Signed-off-by: Josh Durgin <josh.durgin@inktank.com>
Reviewed-by: Sage Weil <sage@inktank.com>
Pull ceph fixes from Sage Weil:
"There is a pair of fixes for double-frees in the recent bundle for
3.10, a couple of fixes for long-standing bugs (sleep while atomic and
an endianness fix), and a locking fix that can be triggered when osds
are going down"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client:
rbd: fix cleanup in rbd_add()
rbd: don't destroy ceph_opts in rbd_add()
ceph: ceph_pagelist_append might sleep while atomic
ceph: add cpu_to_le32() calls when encoding a reconnect capability
libceph: must hold mutex for reset_changed_osds()
Bjorn Helgaas pointed out that a recent commit introduced a
use-after-free condition in an error path for rbd_add().
He correctly stated:
I think b536f69a3a "rbd: set up devices only for mapped images"
introduced a use-after-free error in rbd_add():
...
If rbd_dev_device_setup() returns an error, we call
rbd_dev_image_release(), which ultimately kfrees rbd_dev.
Then we call rbd_dev_destroy(), which references fields in
the already-freed rbd_dev struct before kfreeing it again.
The simple fix is to return the error code after the call to
rbd_dev_image_release().
Closer examination revealed that there's no need to clean up
rbd_opts in that function, so fix that too.
Update some other comments that have also become out of date.
Reported-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
Whether rbd_client_create() successfully creates a new client or
not, it takes responsibility for getting the ceph_opts structure
it's passed destroyed. If successful, the structure becomes
associated with the created client; if not, rbd_client_create()
will destroy it.
Previously, rbd_get_client() would call ceph_destroy_options()
if rbd_get_client() failed, and that meant it got called twice.
That led freeing various pointers more than once, which is never a
good idea.
This resolves:
http://tracker.ceph.com/issues/4559
Cc: stable@vger.kernel.org # 3.8+
Reported-by: Dan van der Ster <dan@vanderster.com>
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
Pull Ceph fixes from Sage Weil:
"Yes, this is a much larger pull than I would like after -rc1. There
are a few things included:
- a few fixes for leaks and incorrect assertions
- a few patches fixing behavior when mapped images are resized
- handling for cloned/layered images that are flattened out from
underneath the client
The last bit was non-trivial, and there is some code movement and
associated cleanup mixed in. This was ready and was meant to go in
last week but I missed the boat on Friday. My only excuse is that I
was waiting for an all clear from the testing and there were many
other shiny things to distract me.
Strictly speaking, handling the flatten case isn't a regression and
could wait, so if you like we can try to pull the series apart, but
Alex and I would much prefer to have it all in as it is a case real
users will hit with 3.10."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client: (33 commits)
rbd: re-submit flattened write request (part 2)
rbd: re-submit write request for flattened clone
rbd: re-submit read request for flattened clone
rbd: detect when clone image is flattened
rbd: reference count parent requests
rbd: define parent image request routines
rbd: define rbd_dev_unparent()
rbd: don't release write request until necessary
rbd: get parent info on refresh
rbd: ignore zero-overlap parent
rbd: support reading parent page data for writes
rbd: fix parent request size assumption
libceph: init sent and completed when starting
rbd: kill rbd_img_request_get()
rbd: only set up watch for mapped images
rbd: set mapping read-only flag in rbd_add()
rbd: support reading parent page data
rbd: fix an incorrect assertion condition
rbd: define rbd_dev_v2_header_info()
rbd: get rid of trivial v1 header wrappers
...
Add code to rbd_img_obj_exists_callback() to detect when a clone's
parent image has disappeared, and re-submit the original write
request in that case.
Kill off some redundant assertions.
This completes the resolution for:
http://tracker.ceph.com/issues/3763
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
Add code to rbd_img_parent_read_full_callback() to detect when a
clone's parent image has disappeared, and re-submit the original
write request in that case. (See the previous commit for more
reasoning about why this is appropriate.)
Rename some variables in rbd_img_obj_parent_read_full_callback()
to match the convention used in the previous patch.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
If a clone image gets flattened while a parent read request is
underway, the original rbd object request needs to be resubmitted.
The reason is that by the time we get the response to the parent
read request, the data read from the parent may be out of date.
In other words, we could see this sequence of events:
rbd client parent image/osd
---------- ----------------
original object ENOENT;
issue parent read
respond to parent read
child image flattened
original image header refresh
<--- original object written independently here
parent read response received
Add code to rbd_img_parent_read_callback() to detect when a clone's
parent image has disappeared (as evidenced by its parent overlap
becoming 0), and re-submit the original read request in that case.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
A format 2 clone image can be the subject of a "flatten" operation,
during which all of its data gets "copied up" from its parent image,
leaving the image fully populated. Once this is complete, the
clone's association with the parent is abolished.
Since this can occur when a clone is mapped, we need to detect when
it has occurred and handle it accordingly. We know an image has
been flattened when we know it at one time had a parent, but we have
learned (via a "get_parent" object class method call) it no longer
has one.
There might be in-flight requests at the point we learn an image has
been flattened, so we can't simply clean up parent data structures
right away. Instead, we'll drop the initial parent reference when
the parent has disappeared (rather than when the image gets
destroyed), which will allow the last in-flight reference to clean
things up when it's complete.
We leverage the fact that a zero parent overlap renders an image
effectively unlayered. We set the overlap to 0 at the point we
detect the clone image has flattened, which allows the unlayered
behavior to take effect immediately, while keeping other parent
structures in place until in-flight requests to complete.
This and the next few patches resolve:
http://tracker.ceph.com/issues/3763
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
Keep a reference count for uses of the parent information for an rbd
device.
An initial reference is set in rbd_img_request_create() if the
target image has a parent (with non-zero overlap). Each image
request for an image with a non-zero parent overlap gets another
reference when it's created, and that reference is dropped when the
request is destroyed.
The initial reference is dropped when the image gets torn down.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
Define rbd_parent_request_create() and rbd_parent_request_destroy()
to handle the creation of parent image requests submitted for
layered image objects. For simplicity, let rbd_img_request_put()
handle dropping the reference to any image request (parent or not),
and call whichever destructor is appropriate on the last put.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
Define rbd_dev_unparent() to encapsulate cleaning up parent data
structures from a layered rbd image.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
Previously when a layered write was going to involve a copyup
request, the original osd request was released before submitting the
parent full-object read. The osd request for the copyup would then
be allocated in rbd_img_obj_parent_read_full_callback().
Shortly we will be handling the event of mapped layered images
getting flattened, and when that occurs we need to resubmit the
original request. We therefore don't want to release the osd
request until we really konw we're going to replace it--in the
callback function.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
Get parent info for format 2 images on every refresh (rather than
just during the initial probe). This will be needed to detect the
disappearance of the parent image in the event a mapped image
becomes unlayered (i.e., flattened). Avoid leaking the previous
parent spec on the second and subsequent times this information is
requested by dropping the previous one (if any) before updating it.
(Also, extract the pool id into a local variable before assigning
it into the parent spec.)
Switch to using a non-zero parent overlap value rather than the
existence of a parent (a non-null parent_spec pointer) to determine
whether to mark a request layered. It will soon be possible for
a layered image to become unlayered while a request is in flight.
This means that the layered flag for an image request indicates that
there was a non-zero parent overlap at the time the image request
was created. The parent overlap can change thereafter, which may
lead to special handling at request submission or completion time.
This and the next several patches are related to:
http://tracker.ceph.com/issues/3763
NOTE:
If an error occurs while refreshing the parent info (i.e.,
requesting it after initial probe), the old parent info will
persist. This is not really correct, and is a scenario that needs
to be addressed. For now we'll assert that the failure mode is
unlikely, but the issue has been documented in tracker issue 5040.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
An rbd clone image that has an overlap with its parent of 0 is
effectively not a layered image at all. Detect this case and treat
such an image as non-layered. Issue a warning to be sure the user
knows what's going on.
This resolves:
http://tracker.ceph.com/issues/5028
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
Currently, rbd_img_obj_parent_read_full() assumes the incoming
object request contains bio data. But if a layered image is part of
a multi-layer stack of images it will result in read requests of
page data to parent images.
This is handling the same kind of issue as was resolved by this
commit:
5b2ab72d rbd: support reading parent page data
This resolves:
http://tracker.ceph.com/issues/5027
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
The code that reads object data from the parent for a copyup on
write request currently assumes that the size of that request is the
size of a "full" object from the original target image.
That is not necessarily the case. The parent overlap could reduce
the request size below that. To fix that assumption we need to
record the number of pages in the copyup_pages array, for both an
image request and an object request. Rename a local variable in
rbd_img_obj_parent_read_full_callback() to reflect we're recording
the length of the parent read request, not the size of the target
object.
This resolves:
http://tracker.ceph.com/issues/5038
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
Get rid of rbd_img_request_get(), because it isn't used, and maybe
won't ever be needed.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
Any changes to parent images are immaterial to any mapped clone.
So there is no need to have a watch event registered on header
objects except for the header object of an image that is mapped.
In fact, a watch request is a write operation, and we may only
have read access to a parent image.
We can't set up the watch request until we know the name of the
header object though. So pass a flag to rbd_dev_image_probe() to
indicate whether this probe is for a mapping or for a parent image.
Change the second parameter to rbd_dev_header_watch_sync() be
Boolean while we're at it.
This resolves:
http://tracker.ceph.com/issues/4941
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
The rbd_dev->mapping field for a parent image is not meaningful.
Since rbd_image_probe() is used both for images being mapped and
their parents, it doesn't make sense to set that flag in that
function.
So move the setting of the mapping.read_only flag out of
rbd_dev_image_probe() and into rbd_add() instead.
This resolves:
http://tracker.ceph.com/issues/4940
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
Currently, rbd_img_parent_read() assumes the incoming object request
contains bio data. But if a layered image is part of a multi-layer
stack of images it will result in read requests of page data to parent
images.
Fortunately, it's not hard to add support for page data.
This resolves:
http://tracker.ceph.com/issues/4939
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
In rbd_img_obj_parent_read_full_callback() there is an assertion
intended to verify the size of the image request for a full parent
read was the size of the original request's target object. But
assertion was looking at the parent image order rather than the
original one, and these values can differ.
Fix that.
This resolves:
http://tracker.ceph.com/issues/4938
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
This rearranges rbd_dev_v2_refresh() so it works more like
rbd_dev_v1_header_info(). While format 1 images need to read the
whole header object to get any information, format 2 can collect
almost all information selectively. So the one-time initialization
will remain in a separate function--based on rbd_dev_v2_probe().
Rename rbd_dev_v2_refresh() to be rbd_dev_v2_header_info(), and have
it call rbd_dev_v2_header_onetime() if it's being called for the
first time for the given rbd device.
Rename rbd_dev_v2_probe() to be rbd_dev_v2_header_onetime() and
remove the image size and snapshot context calls it held in
common with the refresh function.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
Get rid of the trivial wrapper functions rbd_dev_v1_refresh() and
rbd_dev_v1_probe(), substituting rbd_dev_v1_header_read() calls
in their place.
Rename rbd_dev_v1_header_read() to be rbd_dev_v1_header_info(), to
be more generic (it will better reflect what happens with format 2
images).
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
An rbd_dev structure's fields are all zero-filled for an initial
probe, so there's no need to explicitly zero the parent_spec
and parent_overlap fields in rbd_dev_v1_probe(). Removing these
assignments makes rbd_dev_v1_probe() *almost* trivial.
Move the dout() message that announces discovery of an image into
rbd_dev_image_probe(), generalize to support images in either format
and only show it if an image is fully discovered.
This highlights that are some unnecessary cleanups in the error
path for rbd_dev_v1_probe(), so they can be removed.
Now rbd_dev_v1_probe() *is* a trivial wrapper function.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
Now that rbd_header_from_disk() only fills in one-time fields once,
we can extend it slightly so it releases the other fields before
replacing their values. This way there's no need to pass a
temporary buffer and then copy all the results in. Just use the rbd
device header structure in rbd_header_from_disk() so its values get
updated directly.
Note that this means we need to take the header semaphore at the
point we update things. So pass the rbd_dev rather than the address
of its header as its first argument to rbd_header_from_disk(), and
have it return an error code.
As a result, rbd_dev_v1_header_read() does all the work,
rbd_read_header() becomes unnecessary, and rbd_dev_v1_refresh()
becomes a very simple wrapper.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
This rearranges rbd_header_from_disk so that it:
- allocates the snapshot context right away
- keeps results in local variables, not changing the passed-in
header until it's known we'll succeed
- does initialization of set-once fields in a header only if
they have not already been set
The last point is moot at the moment, because rbd_read_header()
(the only caller) always supplies a zero-filled header buffer.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
The passed-in header structure is zeroed in rbd_header_from_disk().
Instead, have the caller do it. Note that there are two callers,
rbd_dev_v1_refresh() and rbd_dev_v1_probe(). The latter already has
a zeroed header structure so zeroing it isn't necessary there.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
Defer setting the size and features fields of a mapped image until
after the Linux disk structure is set up. Set the capacity of the
disk after that.
Rearrange the definition of rbd_image_header, separating the fields
that are set only once from those that can be updated.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
Pull block core updates from Jens Axboe:
- Major bit is Kents prep work for immutable bio vecs.
- Stable candidate fix for a scheduling-while-atomic in the queue
bypass operation.
- Fix for the hang on exceeded rq->datalen 32-bit unsigned when merging
discard bios.
- Tejuns changes to convert the writeback thread pool to the generic
workqueue mechanism.
- Runtime PM framework, SCSI patches exists on top of these in James'
tree.
- A few random fixes.
* 'for-3.10/core' of git://git.kernel.dk/linux-block: (40 commits)
relay: move remove_buf_file inside relay_close_buf
partitions/efi.c: replace useless kzalloc's by kmalloc's
fs/block_dev.c: fix iov_shorten() criteria in blkdev_aio_read()
block: fix max discard sectors limit
blkcg: fix "scheduling while atomic" in blk_queue_bypass_start
Documentation: cfq-iosched: update documentation help for cfq tunables
writeback: expose the bdi_wq workqueue
writeback: replace custom worker pool implementation with unbound workqueue
writeback: remove unused bdi_pending_list
aoe: Fix unitialized var usage
bio-integrity: Add explicit field for owner of bip_buf
block: Add an explicit bio flag for bios that own their bvec
block: Add bio_alloc_pages()
block: Convert some code to bio_for_each_segment_all()
block: Add bio_for_each_segment_all()
bounce: Refactor __blk_queue_bounce to not use bi_io_vec
raid1: use bio_copy_data()
pktcdvd: Use bio_reset() in disabled code to kill bi_idx usage
pktcdvd: use bio_copy_data()
block: Add bio_copy_data()
...
Hold off setting the read-only flag in rbd_add() for an image being
mapped until we have successfully probed the image. At that point
we know whether it's a snapshot mapping or not, so we can set the
read-only flag in that one place rather than doing so (for
snapshots) in rbd_dev_mapping_set(). To do this, pass a flag to the
image probe routine indicating whether we want a read-only mapping.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
This function is a duplicate of rbd_dev_mapping_clear(), and was
added by mistake.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
Currently rbd_dev_mapping_set() looks up the snapshot id for the
snapshot whose name is found in the rbd device's spec structure.
That function gets called by rbd_dev_device_setup(), which is
called by rbd_add() *after* rbd_dev_image_probe(). If the
image probe succeeds, the rbd device's spec will already have
been updated to include names and ids for all fields.
Therefore there's no need to look up the snapshot id in
rbd_dev_mapping_set().
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
The presence of the LAYERING bit in an rbd image's feature mask does
not guarantee the image actually has a parent image. Currently that
bit is set only when a clone (i.e., image with a parent) is created,
but it is (currently) not cleared if that clone gets flattened back
into a "normal" image. A "parent_id" query will leave the
parent_spec for the image being mapped a null pointer, but will not
return an error.
Currently, whenever an image with the LAYERED feature gets mapped, a
warning about the use of layered images gets printed. But we don't
want to do this for a flattened image, so print the warning only
if we find there is a parent spec after the probe.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
Since rbd_update_mapping_size() is now a trivial wrapper, just open
code it in its two callers.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
When a mapped image changes size, we change the capacity recorded
for the Linux disk associated with it, in rbd_update_mapping_size().
That function is called in two places--the format 1 and format 2
refresh routines.
There is no need to set the capacity while holding the header
semaphore. Instead, do it in the common rbd_dev_refresh(), using
the logic that's already there to initiate disk revalidation.
Add handling in the request function, just in case a request
that exceeds the capacity of the device comes in (perhaps one
that was started before a refresh shrunk the device).
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
This commit:
d98df63e rbd: revalidate_disk upon rbd resize
instituted a call to revalidate_disk() to notify interested parties
that a mapped image has changed size. This works well, as long as
the the rbd device doesn't map a snapshot.
A snapshot will never change size. However, the base image the
snapshot is associated with can, and it can do so while the snapshot
is mapped.
The problem is that the test for the size is looking at the size of
the base image, not the size of the mapped snapshot. This patch
corrects that.
Update the warning message shown in the event of error, and move
it into the callers.
This resolves:
http://tracker.ceph.com/issues/4911
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
When rbd_dev_v2_refresh() is called, the rbd device already has a
snapshot context associated with it. But that never gets freed,
the pointer just gets overwritten.
Fix this by dropping the rbd device's reference to the snapshot
context before overwriting the pointer.
Because ceph_put_snap_context() already handles for a null pointer
we don't need to check for that (for the probe case, where no
context has yet been assigned).
This resolves:
http://tracker.ceph.com/issues/4912
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
Pull more vfs updates from Al Viro:
"A couple of fixes + getting rid of __blkdev_put() return value"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
proc: Use PDE attribute setting accessor functions
make blkdev_put() return void
block_device_operations->release() should return void
mtd_blktrans_ops->release() should return void
hfs: SMP race on directory close()
The value passed is 0 in all but "it can never happen" cases (and those
only in a couple of drivers) *and* it would've been lost on the way
out anyway, even if something tried to pass something meaningful.
Just don't bother.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
When a read for a layered image object finds the target object
doesn't exist, a read image request for the parent image is created
and submitted. When that completes, the callback routine was
not releasing that parent image request. Fix that.
The slab allocation stuff just added has greatly simplified the
search for the source of this memory leak.
This resolves:
http://tracker.ceph.com/issues/4803
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
The names of objects used for image object requests are always fixed
size. So create a slab cache to manage them. Define a new function
rbd_segment_name_free() to match rbd_segment_name() (which is what
supplies the dynamically-allocated name buffer).
This is part of:
http://tracker.ceph.com/issues/3926
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
Create a slab cache to manage rbd_obj_request allocation. We aren't
using a constructor, and we'll zero-fill object request structures
when they're allocated.
This is part of:
http://tracker.ceph.com/issues/3926
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
The next patch will define a slab allocator for a object requests.
To use that we'll need to allocate the name of an object separate
from the request structure itself.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
Create a slab cache to manage rbd_img_request allocation. Nothing
too fancy at this point--we'll still initialize everything at
allocation time (no constructor)
This is part of:
http://tracker.ceph.com/issues/3926
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
Use bsearch(3) to make snapshot lookup by id more efficient. (There
could be thousands of snapshots, and conceivably many more.)
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
This functionality inadvertently disappeared in the last patch.
Image snapshots can get removed at just about any time. In
particular it can disappear even if it is in use by an rbd
client as a mapped image.
The rbd client deals with such a disappearance by responding to new
requests with ENXIO. This is implemented by each rbd device
maintaining an EXISTS flag, which is normally set but cleared if a
snapshot disappears.
This patch (re-)implements the clearing of that flag.
Whenever mapped image header information is refreshed, if the
mapping is for a snapshot, verify the mapped snapshot is still
present in the updated snapshot context. If it is not, clear the
flag.
It is not necessary to check this in the initial probe, because the
probe will not succeed if the snapshot doesn't exist.
This resolves:
http://tracker.ceph.com/issues/4880
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
We no longer use the snapshot list for anything. When we need to
look up a snapshot name, id, size, or feature mask, we just do it
directly rather than relying on this list being updated with every
refresh. The main reason it existed was for the benefit of the
device/sysfs entries that previously were associated with snapshots.
So get rid of the snapshot list, and struct rbd_snap, and the
hundreds of lines of code that supported them.
This resolves:
http://tracker.ceph.com/issues/4868
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
This patch defines a handful of new functions that will allow
us to get rid of the rbd device structure's list of snapshots.
Define rbd_snap_id_by_name() to look up a snapshot id given its
name. This is efficient for format 1 images but not for format 2.
Fortunately it only gets called at mapping time so it's not that
critical.
Use rbd_snap_id_by_name() to find out the id for a snapshot getting
mapped, and pass that id to new functions rbd_snap_size() and
rbd_snap_features() to look up information about a given snapshot's
size and feature mask given its snapshot id. All this gets done
in rbd_dev_mapping_set().
As a result, snap_by_name() is no longer needed, so get rid of it.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
In order to align with what was needed for format 1 rbd images,
rbd_dev_v2_snap_info() was set up to take as argument an index into
the array of snapshot ids in a rbd device's snapshot context.
This switches that around, so we pass the snapshot id instead.
In doing this, rbd_snap_name() now returns a dynamically-allocated
string rather than a fixed one, so there's no need to make a
duplicate in its caller, rbd_dev_spec_update().
This means the following functions take a snapshot id where they
previously used an index value:
rbd_dev_snap_info()
rbd_dev_v1_snap_info()
rbd_dev_v2_snap_info()
A new function, rbd_dev_snap_index(), determines the snap index for
format 1 images and uses it to look up the name.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
Rather than scanning the list of snapshot structures for it, scan
the snapshot context buffer containing snapshot names in order to
determine for a format 1 image the name associated with a given
snapshot id.
Pull out the part of rbd_dev_v1_snap_info() that does this scan into
a new function, _rbd_dev_v1_snap_name(). Have that function return
a dynamically-allocated copy of the name, and don't duplicate it in
rbd_dev_v1_snap_info().
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
Nothing ever uses the version field maintained in the object request
structure any more, so get rid of it.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
Only NULL is passed as the version argument to rbd_obj_method_sync(),
so get rid of it.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
Continued from the last patch, more parameters that can go away
because we no longer have a need to track object versions.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
Several functions in rbd have parameters meant to allow the version
of an object to be passed in or out. The purpose of those was to
allow the version of a header object to be maintained, but we no
longer do that. As a result, these parameters are never actually
needed or used, so get rid of them.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
The rbd code takes care to maintain the version of the header
object. This was done in hopes of using it to detect a change in
the object between reading it and setting up a watch request to
be notified of changes.
The mechanism was never fully implemented, however. And we now
avoid the original problem by setting up the watch request before
ever reading the content of the header.
The osd doesn't interpret the object version supplied with a WATCH
osd op, nor does it use the version supplied with a NOTIFY_ACK op
(we can just supply 0 for both). There is therefore no need to
maintain the header's object version any more, so stop doing so.
We'll be able to simplify some more rbd code in the next few patches
as a result of this.
This resolves:
http://tracker.ceph.com/issues/3952
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
Make explicit that snapshot names don't change by making functions
return and take parameters that that point to const qualified data.
This resolves:
http://tracker.ceph.com/issues/4867
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
Whenever a header object event causes a mapped rbd image to refresh
its header information, revalidate_disk() is being called. This was
done in rbd_dev_refresh() outside the control mutex in order to
avoid a lock inversion. Although a an event like this *might*
indicate the image has changed size, most of the time it does not.
Record the image size before and after the refresh, and only
call revalidate_disk() if it changes.
This resolves:
http://tracker.ceph.com/issues/4867
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
A warning gets spewed for any image being probed, including parent
images. Set up a condition such that the warning message only gets
printed for the image being mapped, not any of its parents.
Also, I didn't like the way the warning ended up being so long.
Make it a terse warning instead. People experimenting with layering
will know what the message means.
This is part of:
http://tracker.ceph.com/issues/4867
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
Now that we have a library routine to create snap contexts, use it.
This is part of:
http://tracker.ceph.com/issues/4857
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
Stop setting up Linux devices during the image probe operation.
Instead, set up the devices as a separate step after the image
probe, in rbd_add().
A consequence of this is that only mapped images get devices
assigned to them, which is pretty sweet.
This resolves:
http://tracker.ceph.com/issues/4774
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
Currently an rbd_device structure gets destroyed from the release
routine for the device embedded within it. Stop doing that, instead
calling rbd_dev_image_release() right after rbd_bus_del_dev()
wherever the latter is called.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
Define a new function rbd_dev_unprobe() which undoes state changes
that occur from calling rbd_dev_v1_probe() or rbd_dev_v2_probe().
Note that this is a superset of rbd_header_free(), which is now
getting removed (it seems to have been used improperly anyway).
Flesh out rbd_dev_image_release() so it undoes exactly what
rbd_dev_image_probe() does.
This means that:
- rbd_dev_device_release() gets called when the last device
reference gets dropped;
- that undoes everything done by the rbd_dev_device_setup() call
at the end of rbd_dev_image_probe() (and nothing more), ending
by calling rbd_dev_image_release(); and
- rbd_dev_image_release() undoes everything else done by
rbd_dev_image_probe() (and this includes a call to
rbd_dev_unprobe().
This means the image and device portions of an rbd device are fairly
cleanly separated now, so error paths should be a little easier to
verify than they used to be.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
Rename rbd_dev_probe_finish() to be rbd_dev_device_setup(). Its
purpose is to set up the Linux side of an rbd device mapping.
Rename rbd_dev_release() to be rbd_dev_device_release(), making
it more obvious it serves as the inverse of the setup function
(or it will).
Encapsulate some of what was done in rbd_dev_release() into a new
function rbd_dev_image_release(), which serves as the inverse of
setting up the ceph side of the mapped rbd image.
Define a new helper rbd_dev_clear_mapping() to simply zero out the
fields of a mapping structure--the inverse of rbd_dev_set_mapping().
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
Drop the module reference at the end of rbd_remove() for symmetry
with adding a reference at the top of rbd_add().
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
Move setting up the watch request for an image so it's done in
rbd_dev_image_probe() rather than rbd_dev_probe_finish(). Move
it all the way up to before doing the initial probe. This avoids
a potential race condition, in which we get (and use) the initial
snapshot context for an image, and it gets changed between that
time and the time we get the watch set up.
This resolves:
http://tracker.ceph.com/issues/3871
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
When a format 2 image is refreshed, code is in place to verify that
the object order never changes from what it was originally. This
relies on the fact that the refresh will occur *after* an initial
load of information about the image.
An upcoming patch makes it possible for the refresh to occur first,
so we can no longer make this order check. The order really can't
ever change anyway--this was just a sanity check. So get rid of it.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
Currently, a watch on an rbd device header object gets torn down
when its final Linux device reference gets dropped. Instead, tear
it down when removing the device. If an error occurs cleaning up
the watch event when unmapping, abort the unmap request.
All images (including parents) still get watch requests set up, so
tear these down also, in rbd_dev_remove_parent(). For now, ignore
any errors that occur in this case.
Get rid of local variable "rc" in rbd_remove(); use "ret" instead
(they both somehow ended up defined in the function and only one is
needed).
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
Define a new function rbd_header_name(), which allocates and formats
the name of the header object for the rbd device.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
Move a block of initialization related to the "ceph-side" of an rbd
image out of rbd_dev_probe_finish() and into rbd_dev_image_probe().
Add appropriate error handling to clean things up in the event any
of these new functions return an error.
We know that rbd_dev_snaps_update(), rbd_dev_spec_update(), and
rbd_dev_probe_parent() all clean up after themselves before they
return an error, so no special cleanup is required except when an
earlier call succeeds. Since rbd_dev_spec_update() only updates the
spec field (whose cleanup will be handled by dropping the last
reference to the spec) there is no cleanup action associatied with
that.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
Probe for a parent device earlier in rbd_dev_probe_finish(), before
starting to set up the Linux side of the rbd device.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
When an error occurs while finishing probing a device it is assumed
that parent devices get cleaned up when deleting a device. They
don't. Add a call to clean them up. Note that this means the
parent spec will already be cleaned up so it doesn't have to be
in one of the rbd_add() error paths.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
In certain error paths, it is possible for an rbd device to have a
parent spec but no parent rbd_dev. In rbd_dev_remove_parent() use
the parent field rather than parent_spec in determining whether to
try to remove any parent devices. Use assertions to indicate that
any non-null parent pointer has parent_spec associated with it.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
The function __rbd_remove() is used in two spots, and it's fairly
simple. It combines cleanup of part of the ceph-side state as well
as cleaning up the Linux-side state. Just open code it in the two
callers and eliminate the function.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
Set the mapping size and features earlier in rbd_dev_probe_finish().
Define rbd_dev_mapping_clear() as an inverse for setting those
fields, and use it both in error handling in rbd_dev_image_probe()
and in the final cleanup in rbd_dev_release(). Change the name
of rbd_dev_set_mapping() to of rbd_dev_mapping_set().
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
Encapsulate the code that removes an rbd device's parent images into
a new function, rbd_dev_remove_parent().
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
Encapsulate the code that probes for an rbd device's parent images
into a new function, rbd_dev_probe_parent().
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
Don't set the disk capacity until right before we announce the
device as available for use.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
Hold off setting the EXISTS rbd device flag until just before we
announce the disk as available for use. There's no point in doing
so any earlier than that, and at that point the device truly is
fully set up and ready to use.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
This just tweaks a few things in the routines that implement
rbd sysfs files.
All of the entries for an rbd device in /sys/bus/rbd/devices/<id>/
will represent information whose valid values are known by the time
they are accessible.
Right now we get the size of the mapped image by a call to
get_capacity(). There's no need to do this, because that will
return what we last set the capacity to, which is just the size
recorded for the mapping. So just show that value instead.
We also get this under protection of the header semaphore, in order
to provide a precisely correct value. This isn't really necessary;
these files are really informational only and it's not necessary to
be so careful.
Finally, print a special value in case the major device number is
not recorded. Right now that won't matter much but soon the parent
images won't have devices associated with them.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
When a snapshot context update occurs, rbd_update_mapping_size() is
called to set the capacity of the disk to record the updated
size of the image in case it has changed.
There's a bug though. The mapping size is in units of *bytes*. The
code that updates the mapping size field is assigning a value that
has been scaled down to *sectors*.
Fix that. Also, check to see if the size has actually changed, and
don't bother updating things (specifically, calling set_capacity())
if it has not.
This resolves:
http://tracker.ceph.com/issues/4833
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
Fairly straightforward refactoring of rbd_dev_probe_update_spec().
The name is changed to rbd_dev_spec_update().
Rearrange it so nothing gets assigned to the spec until all of the
names have been successfully acquired.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
Rename rbd_dev_probe() to be rbd_dev_image_probe(). Its purpose
will eventually be to probe for the existence of a valid rbd image
for the rbd device--focusing only on the ceph side and not the Linux
device side of initialization.
For now the two "sides" are not fully separated, and this function
is still the entry point for initializing the full rbd device.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
Currently, rbd_dev_destroy() does more than just the inverse of what
rbd_dev_create() does. Stop doing that, and move the two extra
things it does into the three call sites.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
Encapsulate the creation of a snapshot context for rbd in a new
function rbd_snap_context_create(). Define rbd wrappers for getting
and dropping references to them once they're created.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
Change some calls to WARN_ON() so they use rbd_warn() instead, so we
get consistent messaging. A few remain but they can probably just
go away eventually.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
This commit added fetching if fancy striping parameters:
09186ddb rbd: get and check striping parameters
They are almost unused, but the two fields storing the information
really belonged in the rbd_image_header structure.
This patch moves them there.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
Make the names and image id in an rbd_spec be pointers to constant
data. This required the use of a local variable to hold the
snapshot name in rbd_add_parse_args() to avoid a warning.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
Set the rbd spec's snapshot id for an image getting mapped in
rbd_dev_probe_update_spec() rather than rbd_dev_set_mapping().
This is the more logical place for that to happen (even though
it means we might look up the snapshot by name twice).
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
A function called snap_by_name() ought to just look up a snapshot by
name. It does that, but then it assigns some stuff to the rbd
device structure as well.
Change the function to do just the lookup, and have the caller do
the assignments that follow.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
If a format 2 image id is found for an image being mapped, but the
subsequent probe of the image fails, rbd_dev_probe() quits without
freeing the image id. Fix that.
Also drop a redundant hunk of code in rbd_dev_image_id().
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
Currently, rbd_dev_probe() assumes that any error returned by
rbd_dev_image_id() is most likely -ENOENT, and responds by
calling the format 1 probe routine, rbd_dev_v1_probe(). Then,
at the top of rbd_dev_v1_probe(), an empty string is allocated
for the image id.
This is sort of unbalanced. Fix this by having rbd_dev_image_id()
look for -ENOENT from its "get_id" method call. If that is seen,
have it allocate the empty string there rather than depending on
rbd_dev_v1_probe() to do it.
Given that this is effectively defining the format of the image,
set rbd_dev->image_format inside rbd_dev_image_id() rather than in
the format-specific probe routines.
Also drop a redundant hunk of code in rbd_dev_image_id().
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
I found during some failure injection testing that the call to
rbd_free_disk() in the error path of rbd_dev_probe_finish() was
dropping an extra reference to the disk queue. The problem
occurred when put_disk tried to drop a reference to the disk's
queue. A call to blk_cleanup_queue() just prior to that will have
also dropped a reference to the queue.
The problem is that the reference dropped by put_disk() is assumed
to have been taken by add_disk(). Our code has error paths that can
occur after the disk and its queue are initialized, but before the
call to add_disk(), and in those paths we won't have that extra
reference.
The fix is easy though. In rbd_free_disk() we're already checking
the disk's GENHD_FL_UP flag. That flag is an indication that
add_disk() has been called, so just call blk_cleanup_queue()
conditional on that flag being set.
This resolves:
http://tracker.ceph.com/issues/4800
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
Now that rbd_obj_method_sync() returns the number of bytes
returned by the method call, that value should be used by
callers to ensure we don't overrun the valid portion of the
buffer.
Fix the two spots that remained that weren't doing that,
rbd_dev_image_name() and rbd_dev_v2_snap_name().
Rearrange the error path slightly in rbd_dev_v2_snap_name().
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
When the snapshot context for an rbd device gets updated (or the
initial one is recorded) a a list of snapshot structures is created
to represent them, one entry per snapshot. Each entry includes a
dynamically-allocated copy of the snapshot name.
Currently the name is allocated in rbd_snap_create(), as a duplicate
of the passed-in name.
For format 1 images, the snapshot name provided is just a pointer to
an existing name. But for format 2 images, the passed-in name is
already dynamically allocated, and in the the process of duplicating
it here we are leaking the passed-in name.
Fix this by dynamically allocating the name for format 1 snapshots
also, and then stop allocating a duplicate in rbd_snap_create().
Change rbd_dev_v1_snap_info() so none of its parameters is
side-effected unless it's going to return success.
This is part of:
http://tracker.ceph.com/issues/4803
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
Rename __rbd_add_snap_dev() to be rbd_snap_create(). We no longer
have devices for non-mapped snapshots, and we're not actually
"adding" it to the list in this function, just creating it.
Rename rbd_remove_snap_dev() to be rbd_snap_destroy() for reasons
similar to the above. Stop having this function delete the snapshot
from its list (to be symmetrical with its create counterpart) and do
that in the caller instead.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
Change rbd_dev_v2_snap_info() so it only ever sets values of the
size and features parameters if looking up the snapshot name was
successful.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
Only one of the two callers of _rbd_dev_v2_snap_size() needs the
order value returned. So make that an optional argument--a null
pointer if the caller doesn't need it.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
When an rbd image is initially mapped, its snapshot context is
collected, and then a list of snapshot entries representing the
snapshots in that context is created. The list is created using
rbd_dev_snaps_update(). (This function also supports updating an
existing snapshot list based on a new snapshot context.)
If an error occurs, updating the list is aborted, and the list is
currently left as-is, in an inconsistent state. At that point,
there may be a partially-constructed list, but the calling functions
(rbd_dev_probe_finish() from rbd_dev_probe() from rbd_add()) never
clean them up. So this constitutes a leak.
A snapshot list that is inconsistent with the current snapshot
context is of no use, and might even be actively bad. So rather
than just having the caller clean it up, have rbd_dev_snaps_update()
just clear out the entire snapshot list in the event an error
occurs.
The other place rbd_dev_snaps_update() is used is when a refresh is
triggered, either because of a watch callback or via a write to the
/sys/bus/rbd/devices/<id>/refresh interface. An error while
updating the snapshots has no substantive effect in either of those
cases, but one of them issues a warning. Move that warning to the
common rbd_dev_refresh() function so it gets issued regardless of
how it got initiated.
This is part of:
http://tracker.ceph.com/issues/4803
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
When an rbd image gets mapped a device entry gets created for it
under /sys/bus/rbd/devices/<id>/. Inside that directory there are
sysfs files that contain information about the image: its size,
feature bits, major device number, and so on.
Additionally, if that image has any snapshots, a device entry gets
created for each of those as a "child" of the mapped device. Each
of these is a subdirectory of the mapped device, and each directory
contains a few files with information about the snapshot (its
snapshot id, size, and feature mask).
There is no clear benefit to having those device entries for the
snapshots. The information provided via sysfs of of little real
value--and all of it is available via rbd CLI commands. If we
still wanted to see the kernel's view of this information it could
be done much more simply by including it in a single sysfs file for
the mapped image.
But there *is* a clear cost to supporting them. Every time a snapshot
context changes, these entries need to be updated (deleted snapshots
removed, new snapshots created). The rbd driver is notified of
changes to the snapshot context via callbacks from an osd, and care
must be taken to coordinate removal of snapshot data structures
with the possibility of one these notifications occurring.
Things would be considerably simpler if we just didn't have to
maintain device entries for the snapshots.
So get rid of them.
The ability to map a snapshot of an rbd image will remain; the only
thing lost will be the ability to query these sysfs directories for
information about snapshots of mapped images.
This resolves:
http://tracker.ceph.com/issues/4796
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
Now that we have most everything in place to support layered rbd
images, enable support for them in the kernel client. Issue a
warning to the log that the support is considered experimental
whenever a format 2 layered image is mapped.
Note that we also have to claim to support the STRIPINGV2 feature,
due to a mistake in the way the rbd CLI set up those flags. This
feature can work if it has the right parameters, and safeguards
have been put in place to reject those images that do not have
compatible parameters.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
If an rbd format 2 image indicates it supports the STRIPINGV2
feature we need to find out its stripe unit and stripe count in
order to know whether we can use it. We don't yet support fancy
striping fully, but if the default parameters are used the behavior
is indistinguishible from non-fancy striping.
This is necessary because some images require the STRIPINGV2 feature
even if they use the default parameters. (Which is to say the feature
bit was erroneously set even if the feature was not used.)
This resolves:
http://tracker.ceph.com/issues/4709
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
Callers of rbd_obj_method_sync() don't know how many bytes of data
got returned by the class method call. As a result, they have been
assuming enough got returned to decode whatever was expected.
This isn't safe. We know how many bytes got transferred, so have
rbd_obj_method_sync() return that amount (rather than just 0) if
the call is successful.
Change all callers to use this return value to ensure decoding of
the results is done safely.
On the other hand, most callers of rbd_obj_method_sync() only
indicate success or failure, so all of *their* callers can simply
test for non-zero result.
This resolves:
http://tracker.ceph.com/issues/4773
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
Make the inbound and outbound data parameters have void rather than
character type for rbd_obj_method_sync(). This makes it more clear
they don't expect typed data, and eliminates the need for some silly
type casts.
One more unrelated change: define the features buffer used in
_rbd_dev_v2_snap_features() to be a packed data structure.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
Make the buf parameter into which the data is to be read have type
void pointer.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
A clone image has a defined overlap point with its parent image.
That is the byte offset beyond which the parent image has no
defined data to back the clone, and anything thereafter can be
viewed as being zero-filled by the clone image.
This is needed because a clone image can be resized. If it gets
resized larger than the snapshot it is based on, the overlap defines
the original size. If the clone gets resized downward below the
original size the new clone size defines the overlap. If the clone
is subsequently resized to be larger, the overlap won't be increased
because the previous resize invalidated any parent data beyond that
point.
This resolves:
http://tracker.ceph.com/issues/4724
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
This implements the main copyup functionality for layered writes.
Here we add a copyup_pages field to the object request, which is
used only for copyup requests to keep track of the page array
containing data read from the parent image.
A copyup request is currently the only request rbd has that requires
two osd operations. Because of this we handle copyup specially.
All image object requests get an osd request allocated when they are
created. For a write request, if a copyup is required, the osd
request originally allocated is released, and a new one (with room
for two osd ops) is allocated to replace it. A new function
rbd_osd_req_create_copyup() allocates an osd request suitable for
a copyup request.
The first op is then filled with a copyup object class method call,
supplying the array of pages containing data read from the parent.
The second op is filled in with the original write request.
The original request otherwise remains intact, and it describes the
original write request (found in the second osd op). The presence
of the copyup op is sort of implicit; a non-null copyup_pages field
could be used to distinguish between a "normal" write request and a
request containing both a copyup call and a write.
This resolves:
http://tracker.ceph.com/issues/3419
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
As a step toward implementing layered writes, implement reading the
data for a target object from the parent image for a write request
whose target object is known to not exist. Add a copyup_pages field
to an image request to track the page array used (only) for such a
request.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
If rbd disk is open and rbd resize is done, new size is not
visible by filesystem. Like is done in virtio-blk and dm driver,
revalidate_disk() permits to update the bd_inode size.
Signed-off-by: Laurent Barbe <laurent@ksperis.com>
Reviewed-by: Alex Elder <elder@inktank.com>
Ilya Dryomov