Sync code to the same with tk4 pub/lts/0017-kabi, except deleted rue
and wujing. Partners can submit pull requests to this branch, and we
can pick the commits to tk4 pub/lts/0017-kabi easly.
Signed-off-by: Jianping Liu <frankjpliu@tencent.com>
Sync kernel codes to the same with 590eaf1fec ("Init Repo base on
linux 5.4.32 long term, and add base tlinux kernel interfaces."), which
is from tk4, and it is the base of tk4.
Signed-off-by: Jianping Liu <frankjpliu@tencent.com>
kvmhv_switch_to_host() in arch/powerpc/kvm/book3s_hv_rmhandlers.S
needs to set kvmppc_vcore->in_guest to 0 to signal secondary CPUs to
continue. This happens after resetting the PCR. Before commit
13c7bb3c57 ("powerpc/64s: Set reserved PCR bits"), r0 would always
be 0 before it was stored to kvmppc_vcore->in_guest. However because
of this change in the commit:
/* Reset PCR */
ld r0, VCORE_PCR(r5)
- cmpdi r0, 0
+ LOAD_REG_IMMEDIATE(r6, PCR_MASK)
+ cmpld r0, r6
beq 18f
- li r0, 0
- mtspr SPRN_PCR, r0
+ mtspr SPRN_PCR, r6
18:
/* Signal secondary CPUs to continue */
stb r0,VCORE_IN_GUEST(r5)
We are no longer comparing r0 against 0 and loading it with 0 if it
contains something else. Hence when we store r0 to
kvmppc_vcore->in_guest, it might not be 0. This means that secondary
CPUs will not be signalled to continue. Those CPUs get stuck and
errors like the following are logged:
KVM: CPU 1 seems to be stuck
KVM: CPU 2 seems to be stuck
KVM: CPU 3 seems to be stuck
KVM: CPU 4 seems to be stuck
KVM: CPU 5 seems to be stuck
KVM: CPU 6 seems to be stuck
KVM: CPU 7 seems to be stuck
This can be reproduced with:
$ for i in `seq 1 7` ; do chcpu -d $i ; done ;
$ taskset -c 0 qemu-system-ppc64 -smp 8,threads=8 \
-M pseries,accel=kvm,kvm-type=HV -m 1G -nographic -vga none \
-kernel vmlinux -initrd initrd.cpio.xz
Fix by making sure r0 is 0 before storing it to
kvmppc_vcore->in_guest.
Fixes: 13c7bb3c57 ("powerpc/64s: Set reserved PCR bits")
Reported-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Jordan Niethe <jniethe5@gmail.com>
Reviewed-by: Alistair Popple <alistair@popple.id.au>
Tested-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20191004025317.19340-1-jniethe5@gmail.com
Currently the reserved bits of the Processor Compatibility
Register (PCR) are cleared as per the Programming Note in Section
1.3.3 of version 3.0B of the Power ISA. This causes all new
architecture features to be made available when running on newer
processors with new architecture features added to the PCR as bits
must be set to disable a given feature.
For example to disable new features added as part of Version 2.07 of
the ISA the corresponding bit in the PCR needs to be set.
As new processor features generally require explicit kernel support
they should be disabled until such support is implemented. Therefore
kernels should set all unknown/reserved bits in the PCR such that any
new architecture features which the kernel does not currently know
about get disabled.
An update is planned to the ISA to clarify that the PCR is an
exception to the Programming Note on reserved bits in Section 1.3.3.
Signed-off-by: Alistair Popple <alistair@popple.id.au>
Signed-off-by: Jordan Niethe <jniethe5@gmail.com>
Tested-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20190917004605.22471-2-alistair@popple.id.au
When an SVM makes an hypercall or incurs some other exception, the
Ultravisor usually forwards (a.k.a. reflects) the exceptions to the
Hypervisor. After processing the exception, Hypervisor uses the
UV_RETURN ultracall to return control back to the SVM.
The expected register state on entry to this ultracall is:
* Non-volatile registers are restored to their original values.
* If returning from an hypercall, register R0 contains the return value
(unlike other ultracalls) and, registers R4 through R12 contain any
output values of the hypercall.
* R3 contains the ultracall number, i.e UV_RETURN.
* If returning with a synthesized interrupt, R2 contains the
synthesized interrupt number.
Thanks to input from Paul Mackerras, Ram Pai and Mike Anderson.
Signed-off-by: Sukadev Bhattiprolu <sukadev@linux.vnet.ibm.com>
Signed-off-by: Claudio Carvalho <cclaudio@linux.ibm.com>
Acked-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20190822034838.27876-8-cclaudio@linux.ibm.com
At present, when running a guest on POWER9 using HV KVM but not using
an in-kernel interrupt controller (XICS or XIVE), for example if QEMU
is run with the kernel_irqchip=off option, the guest entry code goes
ahead and tries to load the guest context into the XIVE hardware, even
though no context has been set up.
To fix this, we check that the "CAM word" is non-zero before pushing
it to the hardware. The CAM word is initialized to a non-zero value
in kvmppc_xive_connect_vcpu() and kvmppc_xive_native_connect_vcpu(),
and is now cleared in kvmppc_xive_{,native_}cleanup_vcpu.
Fixes: 5af5099385 ("KVM: PPC: Book3S HV: Native usage of the XIVE interrupt controller")
Cc: stable@vger.kernel.org # v4.12+
Reported-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20190813100100.GC9567@blackberry
Escalation interrupts are interrupts sent to the host by the XIVE
hardware when it has an interrupt to deliver to a guest VCPU but that
VCPU is not running anywhere in the system. Hence we disable the
escalation interrupt for the VCPU being run when we enter the guest
and re-enable it when the guest does an H_CEDE hypercall indicating
it is idle.
It is possible that an escalation interrupt gets generated just as we
are entering the guest. In that case the escalation interrupt may be
using a queue entry in one of the interrupt queues, and that queue
entry may not have been processed when the guest exits with an H_CEDE.
The existing entry code detects this situation and does not clear the
vcpu->arch.xive_esc_on flag as an indication that there is a pending
queue entry (if the queue entry gets processed, xive_esc_irq() will
clear the flag). There is a comment in the code saying that if the
flag is still set on H_CEDE, we have to abort the cede rather than
re-enabling the escalation interrupt, lest we end up with two
occurrences of the escalation interrupt in the interrupt queue.
However, the exit code doesn't do that; it aborts the cede in the sense
that vcpu->arch.ceded gets cleared, but it still enables the escalation
interrupt by setting the source's PQ bits to 00. Instead we need to
set the PQ bits to 10, indicating that an interrupt has been triggered.
We also need to avoid setting vcpu->arch.xive_esc_on in this case
(i.e. vcpu->arch.xive_esc_on seen to be set on H_CEDE) because
xive_esc_irq() will run at some point and clear it, and if we race with
that we may end up with an incorrect result (i.e. xive_esc_on set when
the escalation interrupt has just been handled).
It is extremely unlikely that having two queue entries would cause
observable problems; theoretically it could cause queue overflow, but
the CPU would have to have thousands of interrupts targetted to it for
that to be possible. However, this fix will also make it possible to
determine accurately whether there is an unhandled escalation
interrupt in the queue, which will be needed by the following patch.
Fixes: 9b9b13a6d1 ("KVM: PPC: Book3S HV: Keep XIVE escalation interrupt masked unless ceded")
Cc: stable@vger.kernel.org # v4.16+
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20190813100349.GD9567@blackberry
Seven fixes, all for bugs introduced this cycle.
The commit to add KASAN support broke booting on 32-bit SMP machines, due to a
refactoring that moved some setup out of the secondary CPU path.
A fix for another 32-bit SMP bug introduced by the fast syscall entry
implementation for 32-bit BOOKE. And a build fix for the same commit.
Our change to allow the DAWR to be force enabled on Power9 introduced a bug in
KVM, where we clobber r3 leading to a host crash.
The same commit also exposed a previously unreachable bug in the nested KVM
handling of DAWR, which could lead to an oops in a nested host.
One of the DMA reworks broke the b43legacy WiFi driver on some people's
powermacs, fix it by enabling a 30-bit ZONE_DMA on 32-bit.
A fix for TLB flushing in KVM introduced a new bug, as it neglected to also
flush the ERAT, this could lead to memory corruption in the guest.
Thanks to:
Aaro Koskinen, Christoph Hellwig, Christophe Leroy, Larry Finger, Michael
Neuling, Suraj Jitindar Singh.
-----BEGIN PGP SIGNATURE-----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=Ju1y
-----END PGP SIGNATURE-----
Merge tag 'powerpc-5.2-5' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
"This is a frustratingly large batch at rc5. Some of these were sent
earlier but were missed by me due to being distracted by other things,
and some took a while to track down due to needing manual bisection on
old hardware. But still we clearly need to improve our testing of KVM,
and of 32-bit, so that we catch these earlier.
Summary: seven fixes, all for bugs introduced this cycle.
- The commit to add KASAN support broke booting on 32-bit SMP
machines, due to a refactoring that moved some setup out of the
secondary CPU path.
- A fix for another 32-bit SMP bug introduced by the fast syscall
entry implementation for 32-bit BOOKE. And a build fix for the same
commit.
- Our change to allow the DAWR to be force enabled on Power9
introduced a bug in KVM, where we clobber r3 leading to a host
crash.
- The same commit also exposed a previously unreachable bug in the
nested KVM handling of DAWR, which could lead to an oops in a
nested host.
- One of the DMA reworks broke the b43legacy WiFi driver on some
people's powermacs, fix it by enabling a 30-bit ZONE_DMA on 32-bit.
- A fix for TLB flushing in KVM introduced a new bug, as it neglected
to also flush the ERAT, this could lead to memory corruption in the
guest.
Thanks to: Aaro Koskinen, Christoph Hellwig, Christophe Leroy, Larry
Finger, Michael Neuling, Suraj Jitindar Singh"
* tag 'powerpc-5.2-5' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
KVM: PPC: Book3S HV: Invalidate ERAT when flushing guest TLB entries
powerpc: enable a 30-bit ZONE_DMA for 32-bit pmac
KVM: PPC: Book3S HV: Only write DAWR[X] when handling h_set_dawr in real mode
KVM: PPC: Book3S HV: Fix r3 corruption in h_set_dabr()
powerpc/32: fix build failure on book3e with KVM
powerpc/booke: fix fast syscall entry on SMP
powerpc/32s: fix initial setup of segment registers on secondary CPU
The hcall H_SET_DAWR is used by a guest to set the data address
watchpoint register (DAWR). This hcall is handled in the host in
kvmppc_h_set_dawr() which can be called in either real mode on the
guest exit path from hcall_try_real_mode() in book3s_hv_rmhandlers.S,
or in virtual mode when called from kvmppc_pseries_do_hcall() in
book3s_hv.c.
The function kvmppc_h_set_dawr() updates the dawr and dawrx fields in
the vcpu struct accordingly and then also writes the respective values
into the DAWR and DAWRX registers directly. It is necessary to write
the registers directly here when calling the function in real mode
since the path to re-enter the guest won't do this. However when in
virtual mode the host DAWR and DAWRX values have already been
restored, and so writing the registers would overwrite these.
Additionally there is no reason to write the guest values here as
these will be read from the vcpu struct and written to the registers
appropriately the next time the vcpu is run.
This also avoids the case when handling h_set_dawr for a nested guest
where the guest hypervisor isn't able to write the DAWR and DAWRX
registers directly and must rely on the real hypervisor to do this for
it when it calls H_ENTER_NESTED.
Fixes: c1fe190c06 ("powerpc: Add force enable of DAWR on P9 option")
Signed-off-by: Suraj Jitindar Singh <sjitindarsingh@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation this program is
distributed in the hope that it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 655 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070034.575739538@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* POWER: support for direct access to the POWER9 XIVE interrupt controller,
memory and performance optimizations.
* x86: support for accessing memory not backed by struct page, fixes and refactoring
* Generic: dirty page tracking improvements
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQEcBAABAgAGBQJc3qV/AAoJEL/70l94x66Dn3QH/jX1Bn0P/RZAIt4w0SySklSg
PqxUKDyBQqB9vN9Qeb9jWXAKPH2CtM3+up/rz7oRnBWp7qA6vXcC/R/QJYAvzdXE
nklsR/oYCsflR1KdlVYuDvvPCPP2fLBU5zfN83OsaBQ8fNRkm3gN+N5XQ2SbXbLy
Mo9tybS4otY201UAC96e8N0ipwwyCRpDneQpLcl+F5nH3RBt63cVbs04O+70MXn7
eT4I+8K3+Go7LATzT8hglD21D/7uvE31qQb6yr5L33IfhU4GB51RZzBXTNaAdY8n
hT1rMrRkAMAFWYZPQDfoMadjWU3i5DIfstKjDxOr9oTfuOEp5Z+GvJwvVnUDg1I=
=D0+p
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM updates from Paolo Bonzini:
"ARM:
- support for SVE and Pointer Authentication in guests
- PMU improvements
POWER:
- support for direct access to the POWER9 XIVE interrupt controller
- memory and performance optimizations
x86:
- support for accessing memory not backed by struct page
- fixes and refactoring
Generic:
- dirty page tracking improvements"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (155 commits)
kvm: fix compilation on aarch64
Revert "KVM: nVMX: Expose RDPMC-exiting only when guest supports PMU"
kvm: x86: Fix L1TF mitigation for shadow MMU
KVM: nVMX: Disable intercept for FS/GS base MSRs in vmcs02 when possible
KVM: PPC: Book3S: Remove useless checks in 'release' method of KVM device
KVM: PPC: Book3S HV: XIVE: Fix spelling mistake "acessing" -> "accessing"
KVM: PPC: Book3S HV: Make sure to load LPID for radix VCPUs
kvm: nVMX: Set nested_run_pending in vmx_set_nested_state after checks complete
tests: kvm: Add tests for KVM_SET_NESTED_STATE
KVM: nVMX: KVM_SET_NESTED_STATE - Tear down old EVMCS state before setting new state
tests: kvm: Add tests for KVM_CAP_MAX_VCPUS and KVM_CAP_MAX_CPU_ID
tests: kvm: Add tests to .gitignore
KVM: Introduce KVM_CAP_MANUAL_DIRTY_LOG_PROTECT2
KVM: Fix kvm_clear_dirty_log_protect off-by-(minus-)one
KVM: Fix the bitmap range to copy during clear dirty
KVM: arm64: Fix ptrauth ID register masking logic
KVM: x86: use direct accessors for RIP and RSP
KVM: VMX: Use accessors for GPRs outside of dedicated caching logic
KVM: x86: Omit caching logic for always-available GPRs
kvm, x86: Properly check whether a pfn is an MMIO or not
...
Commit 70ea13f6e6 ("KVM: PPC: Book3S HV: Flush TLB on secondary radix
threads", 2019-04-29) aimed to make radix guests that are using the
real-mode entry path load the LPID register and flush the TLB in the
same place where those things are done for HPT guests. However, it
omitted to remove a branch which branches around that code for radix
guests. The result is that with indep_thread_mode = N, radix guests
don't run correctly. (With indep_threads_mode = Y, which is the
default, radix guests use a different entry path.)
This removes the offending branch, and also the load and compare that
the branch depends on, since the cr7 setting is now unused.
Reported-by: Suraj Jitindar Singh <sjitindarsingh@gmail.com>
Tested-by: Suraj Jitindar Singh <sjitindarsingh@gmail.com>
Fixes: 70ea13f6e6 ("KVM: PPC: Book3S HV: Flush TLB on secondary radix threads")
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Reimplement Book3S idle code in C, moving POWER7/8/9 implementation
speific HV idle code to the powernv platform code.
Book3S assembly stubs are kept in common code and used only to save
the stack frame and non-volatile GPRs before executing architected
idle instructions, and restoring the stack and reloading GPRs then
returning to C after waking from idle.
The complex logic dealing with threads and subcores, locking, SPRs,
HMIs, timebase resync, etc., is all done in C which makes it more
maintainable.
This is not a strict translation to C code, there are some
significant differences:
- Idle wakeup no longer uses the ->cpu_restore call to reinit SPRs,
but saves and restores them itself.
- The optimisation where EC=ESL=0 idle modes did not have to save GPRs
or change MSR is restored, because it's now simple to do. ESL=1
sleeps that do not lose GPRs can use this optimization too.
- KVM secondary entry and cede is now more of a call/return style
rather than branchy. nap_state_lost is not required because KVM
always returns via NVGPR restoring path.
- KVM secondary wakeup from offline sequence is moved entirely into
the offline wakeup, which avoids a hwsync in the normal idle wakeup
path.
Performance measured with context switch ping-pong on different
threads or cores, is possibly improved a small amount, 1-3% depending
on stop state and core vs thread test for shallow states. Deep states
it's in the noise compared with other latencies.
KVM improvements:
- Idle sleepers now always return to caller rather than branch out
to KVM first.
- This allows optimisations like very fast return to caller when no
state has been lost.
- KVM no longer requires nap_state_lost because it controls NVGPR
save/restore itself on the way in and out.
- The heavy idle wakeup KVM request check can be moved out of the
normal host idle code and into the not-performance-critical offline
code.
- KVM nap code now returns from where it is called, which makes the
flow a bit easier to follow.
Reviewed-by: Gautham R. Shenoy <ego@linux.vnet.ibm.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
[mpe: Squash the KVM changes in]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This merges in the ppc-kvm topic branch from the powerpc tree to get
patches which touch both general powerpc code and KVM code, one of
which is a prerequisite for following patches.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
When running on POWER9 with kvm_hv.indep_threads_mode = N and the host
in SMT1 mode, KVM will run guest VCPUs on offline secondary threads.
If those guests are in radix mode, we fail to load the LPID and flush
the TLB if necessary, leading to the guest crashing with an
unsupported MMU fault. This arises from commit 9a4506e11b ("KVM:
PPC: Book3S HV: Make radix handle process scoped LPID flush in C,
with relocation on", 2018-05-17), which didn't consider the case
where indep_threads_mode = N.
For simplicity, this makes the real-mode guest entry path flush the
TLB in the same place for both radix and hash guests, as we did before
9a4506e11b, though the code is now C code rather than assembly code.
We also have the radix TLB flush open-coded rather than calling
radix__local_flush_tlb_lpid_guest(), because the TLB flush can be
called in real mode, and in real mode we don't want to invoke the
tracepoint code.
Fixes: 9a4506e11b ("KVM: PPC: Book3S HV: Make radix handle process scoped LPID flush in C, with relocation on")
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
This replaces assembler code in book3s_hv_rmhandlers.S that checks
the kvm->arch.need_tlb_flush cpumask and optionally does a TLB flush
with C code in book3s_hv_builtin.c. Note that unlike the radix
version, the hash version doesn't do an explicit ERAT invalidation
because we will invalidate and load up the SLB before entering the
guest, and that will invalidate the ERAT.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
The code in book3s_hv_rmhandlers.S that pushes the XIVE virtual CPU
context to the hardware currently assumes it is being called in real
mode, which is usually true. There is however a path by which it can
be executed in virtual mode, in the case where indep_threads_mode = N.
A virtual CPU executing on an offline secondary thread can take a
hypervisor interrupt in virtual mode and return from the
kvmppc_hv_entry() call after the kvm_secondary_got_guest label.
It is possible for it to be given another vcpu to execute before it
gets to execute the stop instruction. In that case it will call
kvmppc_hv_entry() for the second VCPU in virtual mode, and the XIVE
vCPU push code will be executed in virtual mode. The result in that
case will be a host crash due to an unexpected data storage interrupt
caused by executing the stdcix instruction in virtual mode.
This fixes it by adding a code path for virtual mode, which uses the
virtual TIMA pointer and normal load/store instructions.
[paulus@ozlabs.org - wrote patch description]
Signed-off-by: Suraj Jitindar Singh <sjitindarsingh@gmail.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Implement a real mode handler for the H_CALL H_PAGE_INIT which can be
used to zero or copy a guest page. The page is defined to be 4k and must
be 4k aligned.
The in-kernel real mode handler halves the time to handle this H_CALL
compared to handling it in userspace for a hash guest.
Signed-off-by: Suraj Jitindar Singh <sjitindarsingh@gmail.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
This adds a flag so that the DAWR can be enabled on P9 via:
echo Y > /sys/kernel/debug/powerpc/dawr_enable_dangerous
The DAWR was previously force disabled on POWER9 in:
9654153158 powerpc: Disable DAWR in the base POWER9 CPU features
Also see Documentation/powerpc/DAWR-POWER9.txt
This is a dangerous setting, USE AT YOUR OWN RISK.
Some users may not care about a bad user crashing their box
(ie. single user/desktop systems) and really want the DAWR. This
allows them to force enable DAWR.
This flag can also be used to disable DAWR access. Once this is
cleared, all DAWR access should be cleared immediately and your
machine once again safe from crashing.
Userspace may get confused by toggling this. If DAWR is force
enabled/disabled between getting the number of breakpoints (via
PTRACE_GETHWDBGINFO) and setting the breakpoint, userspace will get an
inconsistent view of what's available. Similarly for guests.
For the DAWR to be enabled in a KVM guest, the DAWR needs to be force
enabled in the host AND the guest. For this reason, this won't work on
POWERVM as it doesn't allow the HCALL to work. Writes of 'Y' to the
dawr_enable_dangerous file will fail if the hypervisor doesn't support
writing the DAWR.
To double check the DAWR is working, run this kernel selftest:
tools/testing/selftests/powerpc/ptrace/ptrace-hwbreak.c
Any errors/failures/skips mean something is wrong.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This merges in the "ppc-kvm" topic branch of the powerpc tree to get a
series of commits that touch both general arch/powerpc code and KVM
code. These commits will be merged both via the KVM tree and the
powerpc tree.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
When the hash MMU is active the AMR, IAMR and UAMOR are used for
pkeys. The AMR is directly writable by user space, and the UAMOR masks
those writes, meaning both registers are effectively user register
state. The IAMR is used to create an execute only key.
Also we must maintain the value of at least the AMR when running in
process context, so that any memory accesses done by the kernel on
behalf of the process are correctly controlled by the AMR.
Although we are correctly switching all registers when going into a
guest, on returning to the host we just write 0 into all regs, except
on Power9 where we restore the IAMR correctly.
This could be observed by a user process if it writes the AMR, then
runs a guest and we then return immediately to it without
rescheduling. Because we have written 0 to the AMR that would have the
effect of granting read/write permission to pages that the process was
trying to protect.
In addition, when using the Radix MMU, the AMR can prevent inadvertent
kernel access to userspace data, writing 0 to the AMR disables that
protection.
So save and restore AMR, IAMR and UAMOR.
Fixes: cf43d3b264 ("powerpc: Enable pkey subsystem")
Cc: stable@vger.kernel.org # v4.16+
Signed-off-by: Russell Currey <ruscur@russell.cc>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Acked-by: Paul Mackerras <paulus@ozlabs.org>
Currently trying to build without IOMMU support will fail:
(.text+0x1380): undefined reference to `kvmppc_h_get_tce'
(.text+0x1384): undefined reference to `kvmppc_rm_h_put_tce'
(.text+0x149c): undefined reference to `kvmppc_rm_h_stuff_tce'
(.text+0x14a0): undefined reference to `kvmppc_rm_h_put_tce_indirect'
This happens because turning off IOMMU support will prevent
book3s_64_vio_hv.c from being built because it is only built when
SPAPR_TCE_IOMMU is set, which depends on IOMMU support.
Fix it using ifdefs for the undefined references.
Fixes: 76d837a4c0 ("KVM: PPC: Book3S PR: Don't include SPAPR TCE code on non-pseries platforms")
Signed-off-by: Jordan Niethe <jniethe5@gmail.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
This makes the handling of machine check interrupts that occur inside
a guest simpler and more robust, with less done in assembler code and
in real mode.
Now, when a machine check occurs inside a guest, we always get the
machine check event struct and put a copy in the vcpu struct for the
vcpu where the machine check occurred. We no longer call
machine_check_queue_event() from kvmppc_realmode_mc_power7(), because
on POWER8, when a vcpu is running on an offline secondary thread and
we call machine_check_queue_event(), that calls irq_work_queue(),
which doesn't work because the CPU is offline, but instead triggers
the WARN_ON(lazy_irq_pending()) in pnv_smp_cpu_kill_self() (which
fires again and again because nothing clears the condition).
All that machine_check_queue_event() actually does is to cause the
event to be printed to the console. For a machine check occurring in
the guest, we now print the event in kvmppc_handle_exit_hv()
instead.
The assembly code at label machine_check_realmode now just calls C
code and then continues exiting the guest. We no longer either
synthesize a machine check for the guest in assembly code or return
to the guest without a machine check.
The code in kvmppc_handle_exit_hv() is extended to handle the case
where the guest is not FWNMI-capable. In that case we now always
synthesize a machine check interrupt for the guest. Previously, if
the host thinks it has recovered the machine check fully, it would
return to the guest without any notification that the machine check
had occurred. If the machine check was caused by some action of the
guest (such as creating duplicate SLB entries), it is much better to
tell the guest that it has caused a problem. Therefore we now always
generate a machine check interrupt for guests that are not
FWNMI-capable.
Reviewed-by: Aravinda Prasad <aravinda@linux.vnet.ibm.com>
Reviewed-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
When we are running as a nested hypervisor, we use a hypercall to
enter the guest rather than code in book3s_hv_rmhandlers.S. This means
that the hypercall handlers listed in hcall_real_table never get called.
There are some hypercalls that are handled there and not in
kvmppc_pseries_do_hcall(), which therefore won't get processed for
a nested guest.
To fix this, we add cases to kvmppc_pseries_do_hcall() to handle those
hypercalls, with the following exceptions:
- The HPT hypercalls (H_ENTER, H_REMOVE, etc.) are not handled because
we only support radix mode for nested guests.
- H_CEDE has to be handled specially because the cede logic in
kvmhv_run_single_vcpu assumes that it has been processed by the time
that kvmhv_p9_guest_entry() returns. Therefore we put a special
case for H_CEDE in kvmhv_p9_guest_entry().
For the XICS hypercalls, if real-mode processing is enabled, then the
virtual-mode handlers assume that they are being called only to finish
up the operation. Therefore we turn off the real-mode flag in the XICS
code when running as a nested hypervisor.
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This adds a new hypercall, H_ENTER_NESTED, which is used by a nested
hypervisor to enter one of its nested guests. The hypercall supplies
register values in two structs. Those values are copied by the level 0
(L0) hypervisor (the one which is running in hypervisor mode) into the
vcpu struct of the L1 guest, and then the guest is run until an
interrupt or error occurs which needs to be reported to L1 via the
hypercall return value.
Currently this assumes that the L0 and L1 hypervisors are the same
endianness, and the structs passed as arguments are in native
endianness. If they are of different endianness, the version number
check will fail and the hcall will be rejected.
Nested hypervisors do not support indep_threads_mode=N, so this adds
code to print a warning message if the administrator has set
indep_threads_mode=N, and treat it as Y.
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
When the 'regs' field was added to struct kvm_vcpu_arch, the code
was changed to use several of the fields inside regs (e.g., gpr, lr,
etc.) but not the ccr field, because the ccr field in struct pt_regs
is 64 bits on 64-bit platforms, but the cr field in kvm_vcpu_arch is
only 32 bits. This changes the code to use the regs.ccr field
instead of cr, and changes the assembly code on 64-bit platforms to
use 64-bit loads and stores instead of 32-bit ones.
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This creates an alternative guest entry/exit path which is used for
radix guests on POWER9 systems when we have indep_threads_mode=Y. In
these circumstances there is exactly one vcpu per vcore and there is
no coordination required between vcpus or vcores; the vcpu can enter
the guest without needing to synchronize with anything else.
The new fast path is implemented almost entirely in C in book3s_hv.c
and runs with the MMU on until the guest is entered. On guest exit
we use the existing path until the point where we are committed to
exiting the guest (as distinct from handling an interrupt in the
low-level code and returning to the guest) and we have pulled the
guest context from the XIVE. At that point we check a flag in the
stack frame to see whether we came in via the old path and the new
path; if we came in via the new path then we go back to C code to do
the rest of the process of saving the guest context and restoring the
host context.
The C code is split into separate functions for handling the
OS-accessible state and the hypervisor state, with the idea that the
latter can be replaced by a hypercall when we implement nested
virtualization.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
[mpe: Fix CONFIG_ALTIVEC=n build]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This adds a parameter to __kvmppc_save_tm and __kvmppc_restore_tm
which allows the caller to indicate whether it wants the nonvolatile
register state to be preserved across the call, as required by the C
calling conventions. This parameter being non-zero also causes the
MSR bits that enable TM, FP, VMX and VSX to be preserved. The
condition register and DSCR are now always preserved.
With this, kvmppc_save_tm_hv and kvmppc_restore_tm_hv can be called
from C code provided the 3rd parameter is non-zero. So that these
functions can be called from modules, they now include code to set
the TOC pointer (r2) on entry, as they can call other built-in C
functions which will assume the TOC to have been set.
Also, the fake suspend code in kvmppc_save_tm_hv is modified here to
assume that treclaim in fake-suspend state does not modify any registers,
which is the case on POWER9. This enables the code to be simplified
quite a bit.
_kvmppc_save_tm_pr and _kvmppc_restore_tm_pr become much simpler with
this change, since they now only need to save and restore TAR and pass
1 for the 3rd argument to __kvmppc_{save,restore}_tm.
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This streamlines the first part of the code that handles a hypervisor
interrupt that occurred in the guest. With this, all of the real-mode
handling that occurs is done before the "guest_exit_cont" label; once
we get to that label we are committed to exiting to host virtual mode.
Thus the machine check and HMI real-mode handling is moved before that
label.
Also, the code to handle external interrupts is moved out of line, as
is the code that calls kvmppc_realmode_hmi_handler().
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This pulls out the assembler code that is responsible for saving and
restoring the PMU state for the host and guest into separate functions
so they can be used from an alternate entry path. The calling
convention is made compatible with C.
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Reviewed-by: Madhavan Srinivasan <maddy@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This is based on a patch by Suraj Jitindar Singh.
This moves the code in book3s_hv_rmhandlers.S that generates an
external, decrementer or privileged doorbell interrupt just before
entering the guest to C code in book3s_hv_builtin.c. This is to
make future maintenance and modification easier. The algorithm
expressed in the C code is almost identical to the previous
algorithm.
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Currently we use two bits in the vcpu pending_exceptions bitmap to
indicate that an external interrupt is pending for the guest, one
for "one-shot" interrupts that are cleared when delivered, and one
for interrupts that persist until cleared by an explicit action of
the OS (e.g. an acknowledge to an interrupt controller). The
BOOK3S_IRQPRIO_EXTERNAL bit is used for one-shot interrupt requests
and BOOK3S_IRQPRIO_EXTERNAL_LEVEL is used for persisting interrupts.
In practice BOOK3S_IRQPRIO_EXTERNAL never gets used, because our
Book3S platforms generally, and pseries in particular, expect
external interrupt requests to persist until they are acknowledged
at the interrupt controller. That combined with the confusion
introduced by having two bits for what is essentially the same thing
makes it attractive to simplify things by only using one bit. This
patch does that.
With this patch there is only BOOK3S_IRQPRIO_EXTERNAL, and by default
it has the semantics of a persisting interrupt. In order to avoid
breaking the ABI, we introduce a new "external_oneshot" flag which
preserves the behaviour of the KVM_INTERRUPT ioctl with the
KVM_INTERRUPT_SET argument.
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
files not using feature fixup don't need asm/feature-fixups.h
files using feature fixup need asm/feature-fixups.h
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This patch moves ASM_CONST() and stringify_in_c() into
dedicated asm-const.h, then cleans all related inclusions.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
[mpe: asm-compat.h should include asm-const.h]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
POWER9 DD1 was never a product. It is no longer supported by upstream
firmware, and it is not effectively supported in Linux due to lack of
testing.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Reviewed-by: Michael Ellerman <mpe@ellerman.id.au>
[mpe: Remove arch_make_huge_pte() entirely]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Notable changes:
- Support for split PMD page table lock on 64-bit Book3S (Power8/9).
- Add support for HAVE_RELIABLE_STACKTRACE, so we properly support live
patching again.
- Add support for patching barrier_nospec in copy_from_user() and syscall entry.
- A couple of fixes for our data breakpoints on Book3S.
- A series from Nick optimising TLB/mm handling with the Radix MMU.
- Numerous small cleanups to squash sparse/gcc warnings from Mathieu Malaterre.
- Several series optimising various parts of the 32-bit code from Christophe Leroy.
- Removal of support for two old machines, "SBC834xE" and "C2K" ("GEFanuc,C2K"),
which is why the diffstat has so many deletions.
And many other small improvements & fixes.
There's a few out-of-area changes. Some minor ftrace changes OK'ed by Steve, and
a fix to our powernv cpuidle driver. Then there's a series touching mm, x86 and
fs/proc/task_mmu.c, which cleans up some details around pkey support. It was
ack'ed/reviewed by Ingo & Dave and has been in next for several weeks.
Thanks to:
Akshay Adiga, Alastair D'Silva, Alexey Kardashevskiy, Al Viro, Andrew
Donnellan, Aneesh Kumar K.V, Anju T Sudhakar, Arnd Bergmann, Balbir Singh,
Cédric Le Goater, Christophe Leroy, Christophe Lombard, Colin Ian King, Dave
Hansen, Fabio Estevam, Finn Thain, Frederic Barrat, Gautham R. Shenoy, Haren
Myneni, Hari Bathini, Ingo Molnar, Jonathan Neuschäfer, Josh Poimboeuf,
Kamalesh Babulal, Madhavan Srinivasan, Mahesh Salgaonkar, Mark Greer, Mathieu
Malaterre, Matthew Wilcox, Michael Neuling, Michal Suchanek, Naveen N. Rao,
Nicholas Piggin, Nicolai Stange, Olof Johansson, Paul Gortmaker, Paul
Mackerras, Peter Rosin, Pridhiviraj Paidipeddi, Ram Pai, Rashmica Gupta, Ravi
Bangoria, Russell Currey, Sam Bobroff, Samuel Mendoza-Jonas, Segher
Boessenkool, Shilpasri G Bhat, Simon Guo, Souptick Joarder, Stewart Smith,
Thiago Jung Bauermann, Torsten Duwe, Vaibhav Jain, Wei Yongjun, Wolfram Sang,
Yisheng Xie, YueHaibing.
-----BEGIN PGP SIGNATURE-----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=ZlBf
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.18-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc updates from Michael Ellerman:
"Notable changes:
- Support for split PMD page table lock on 64-bit Book3S (Power8/9).
- Add support for HAVE_RELIABLE_STACKTRACE, so we properly support
live patching again.
- Add support for patching barrier_nospec in copy_from_user() and
syscall entry.
- A couple of fixes for our data breakpoints on Book3S.
- A series from Nick optimising TLB/mm handling with the Radix MMU.
- Numerous small cleanups to squash sparse/gcc warnings from Mathieu
Malaterre.
- Several series optimising various parts of the 32-bit code from
Christophe Leroy.
- Removal of support for two old machines, "SBC834xE" and "C2K"
("GEFanuc,C2K"), which is why the diffstat has so many deletions.
And many other small improvements & fixes.
There's a few out-of-area changes. Some minor ftrace changes OK'ed by
Steve, and a fix to our powernv cpuidle driver. Then there's a series
touching mm, x86 and fs/proc/task_mmu.c, which cleans up some details
around pkey support. It was ack'ed/reviewed by Ingo & Dave and has
been in next for several weeks.
Thanks to: Akshay Adiga, Alastair D'Silva, Alexey Kardashevskiy, Al
Viro, Andrew Donnellan, Aneesh Kumar K.V, Anju T Sudhakar, Arnd
Bergmann, Balbir Singh, Cédric Le Goater, Christophe Leroy, Christophe
Lombard, Colin Ian King, Dave Hansen, Fabio Estevam, Finn Thain,
Frederic Barrat, Gautham R. Shenoy, Haren Myneni, Hari Bathini, Ingo
Molnar, Jonathan Neuschäfer, Josh Poimboeuf, Kamalesh Babulal,
Madhavan Srinivasan, Mahesh Salgaonkar, Mark Greer, Mathieu Malaterre,
Matthew Wilcox, Michael Neuling, Michal Suchanek, Naveen N. Rao,
Nicholas Piggin, Nicolai Stange, Olof Johansson, Paul Gortmaker, Paul
Mackerras, Peter Rosin, Pridhiviraj Paidipeddi, Ram Pai, Rashmica
Gupta, Ravi Bangoria, Russell Currey, Sam Bobroff, Samuel
Mendoza-Jonas, Segher Boessenkool, Shilpasri G Bhat, Simon Guo,
Souptick Joarder, Stewart Smith, Thiago Jung Bauermann, Torsten Duwe,
Vaibhav Jain, Wei Yongjun, Wolfram Sang, Yisheng Xie, YueHaibing"
* tag 'powerpc-4.18-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (251 commits)
powerpc/64s/radix: Fix missing ptesync in flush_cache_vmap
cpuidle: powernv: Fix promotion from snooze if next state disabled
powerpc: fix build failure by disabling attribute-alias warning in pci_32
ocxl: Fix missing unlock on error in afu_ioctl_enable_p9_wait()
powerpc-opal: fix spelling mistake "Uniterrupted" -> "Uninterrupted"
powerpc: fix spelling mistake: "Usupported" -> "Unsupported"
powerpc/pkeys: Detach execute_only key on !PROT_EXEC
powerpc/powernv: copy/paste - Mask SO bit in CR
powerpc: Remove core support for Marvell mv64x60 hostbridges
powerpc/boot: Remove core support for Marvell mv64x60 hostbridges
powerpc/boot: Remove support for Marvell mv64x60 i2c controller
powerpc/boot: Remove support for Marvell MPSC serial controller
powerpc/embedded6xx: Remove C2K board support
powerpc/lib: optimise PPC32 memcmp
powerpc/lib: optimise 32 bits __clear_user()
powerpc/time: inline arch_vtime_task_switch()
powerpc/Makefile: set -mcpu=860 flag for the 8xx
powerpc: Implement csum_ipv6_magic in assembly
powerpc/32: Optimise __csum_partial()
powerpc/lib: Adjust .balign inside string functions for PPC32
...
Currently __kvmppc_save/restore_tm() APIs can only be invoked from
assembly function. This patch adds C function wrappers for them so
that they can be safely called from C function.
Signed-off-by: Simon Guo <wei.guo.simon@gmail.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
HV KVM and PR KVM need different MSR source to indicate whether
treclaim. or trecheckpoint. is necessary.
This patch add new parameter (guest MSR) for these kvmppc_save_tm/
kvmppc_restore_tm() APIs:
- For HV KVM, it is VCPU_MSR
- For PR KVM, it is current host MSR or VCPU_SHADOW_SRR1
This enhancement enables these 2 APIs to be reused by PR KVM later.
And the patch keeps HV KVM logic unchanged.
This patch also reworks kvmppc_save_tm()/kvmppc_restore_tm() to
have a clean ABI: r3 for vcpu and r4 for guest_msr.
During kvmppc_save_tm/kvmppc_restore_tm(), the R1 need to be saved
or restored. Currently the R1 is saved into HSTATE_HOST_R1. In PR
KVM, we are going to add a C function wrapper for
kvmppc_save_tm/kvmppc_restore_tm() where the R1 will be incremented
with added stackframe and save into HSTATE_HOST_R1. There are several
places in HV KVM to load HSTATE_HOST_R1 as R1, and we don't want to
bring risk or confusion by TM code.
This patch will use HSTATE_SCRATCH2 to save/restore R1 in
kvmppc_save_tm/kvmppc_restore_tm() to avoid future confusion, since
the r1 is actually a temporary/scratch value to be saved/stored.
[paulus@ozlabs.org - rebased on top of 7b0e827c69 ("KVM: PPC: Book3S HV:
Factor fake-suspend handling out of kvmppc_save/restore_tm", 2018-05-30)]
Signed-off-by: Simon Guo <wei.guo.simon@gmail.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
It is a simple patch just for moving kvmppc_save_tm/kvmppc_restore_tm()
functionalities to tm.S. There is no logic change. The reconstruct of
those APIs will be done in later patches to improve readability.
It is for preparation of reusing those APIs on both HV/PR PPC KVM.
Some slight change during move the functions includes:
- surrounds some HV KVM specific code with CONFIG_KVM_BOOK3S_HV_POSSIBLE
for compilation.
- use _GLOBAL() to define kvmppc_save_tm/kvmppc_restore_tm()
[paulus@ozlabs.org - rebased on top of 7b0e827c69 ("KVM: PPC: Book3S HV:
Factor fake-suspend handling out of kvmppc_save/restore_tm", 2018-05-30)]
Signed-off-by: Simon Guo <wei.guo.simon@gmail.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
This splits out the handling of "fake suspend" mode, part of the
hypervisor TM assist code for POWER9, and puts almost all of it in
new kvmppc_save_tm_hv and kvmppc_restore_tm_hv functions. The new
functions branch to kvmppc_save/restore_tm if the CPU does not
require hypervisor TM assistance.
With this, it will be more straightforward to move kvmppc_save_tm and
kvmppc_restore_tm to another file and use them for transactional
memory support in PR KVM. Additionally, it also makes the code a
bit clearer and reduces the number of feature sections.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
When CONFIG_RELOCATABLE=n, the Linux real mode interrupt handlers call
into KVM using real address. This needs to be translated to the kernel
linear effective address before the MMU is switched on.
kvmppc_bad_host_intr misses adding these bits, so when it is used to
handle a system reset interrupt (that always gets delivered in real
mode), it results in an instruction access fault immediately after
the MMU is turned on.
Fix this by ensuring the top 2 address bits are set when the MMU is
turned on.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
The radix guest code can has fewer restrictions about what context it
can run in, so move this flushing out of assembly and have it use the
Linux TLB flush implementations introduced previously.
This allows powerpc:tlbie trace events to be used.
This changes the tlbiel sequence to only execute RIC=2 flush once on
the first set flushed, then RIC=0 for the rest of the sets. The end
result of the flush should be unchanged. This matches the local PID
flush pattern that was introduced in a5998fcb92 ("powerpc/mm/radix:
Optimise tlbiel flush all case").
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
A radix guest can execute tlbie instructions to invalidate TLB entries.
After a tlbie or a group of tlbies, it must then do the architected
sequence eieio; tlbsync; ptesync to ensure that the TLB invalidation
has been processed by all CPUs in the system before it can rely on
no CPU using any translation that it just invalidated.
In fact it is the ptesync which does the actual synchronization in
this sequence, and hardware has a requirement that the ptesync must
be executed on the same CPU thread as the tlbies which it is expected
to order. Thus, if a vCPU gets moved from one physical CPU to
another after it has done some tlbies but before it can get to do the
ptesync, the ptesync will not have the desired effect when it is
executed on the second physical CPU.
To fix this, we do a ptesync in the exit path for radix guests. If
there are any pending tlbies, this will wait for them to complete.
If there aren't, then ptesync will just do the same as sync.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Currently, the HV KVM guest entry/exit code adds the timebase offset
from the vcore struct to the timebase on guest entry, and subtracts
it on guest exit. Which is fine, except that it is possible for
userspace to change the offset using the SET_ONE_REG interface while
the vcore is running, as there is only one timebase offset per vcore
but potentially multiple VCPUs in the vcore. If that were to happen,
KVM would subtract a different offset on guest exit from that which
it had added on guest entry, leading to the timebase being out of sync
between cores in the host, which then leads to bad things happening
such as hangs and spurious watchdog timeouts.
To fix this, we add a new field 'tb_offset_applied' to the vcore struct
which stores the offset that is currently applied to the timebase.
This value is set from the vcore tb_offset field on guest entry, and
is what is subtracted from the timebase on guest exit. Since it is
zero when the timebase offset is not applied, we can simplify the
logic in kvmhv_start_timing and kvmhv_accumulate_time.
In addition, we had secondary threads reading the timebase while
running concurrently with code on the primary thread which would
eventually add or subtract the timebase offset from the timebase.
This occurred while saving or restoring the DEC register value on
the secondary threads. Although no specific incorrect behaviour has
been observed, this is a race which should be fixed. To fix it, we
move the DEC saving code to just before we call kvmhv_commence_exit,
and the DEC restoring code to after the point where we have waited
for the primary thread to switch the MMU context and add the timebase
offset. That way we are sure that the timebase contains the guest
timebase value in both cases.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
During guest entry/exit, we switch over to/from the guest MMU context
and we cannot take exceptions in the hypervisor code.
Since ftrace may be enabled and since it can result in us taking a trap,
disable ftrace by setting paca->ftrace_enabled to zero. There are two
paths through which we enter/exit a guest:
1. If we are the vcore runner, then we enter the guest via
__kvmppc_vcore_entry() and we disable ftrace around this. This is always
the case for Power9, and for the primary thread on Power8.
2. If we are a secondary thread in Power8, then we would be in nap due
to SMT being disabled. We are woken up by an IPI to enter the guest. In
this scenario, we enter the guest through kvm_start_guest(). We disable
ftrace at this point. In this scenario, ftrace would only get re-enabled
on the secondary thread when SMT is re-enabled (via start_secondary()).
Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Notable changes:
- Support for 4PB user address space on 64-bit, opt-in via mmap().
- Removal of POWER4 support, which was accidentally broken in 2016 and no one
noticed, and blocked use of some modern instructions.
- Workarounds so that the hypervisor can enable Transactional Memory on Power9.
- A series to disable the DAWR (Data Address Watchpoint Register) on Power9.
- More information displayed in the meltdown/spectre_v1/v2 sysfs files.
- A vpermxor (Power8 Altivec) implementation for the raid6 Q Syndrome.
- A big series to make the allocation of our pacas (per cpu area), kernel page
tables, and per-cpu stacks NUMA aware when using the Radix MMU on Power9.
And as usual many fixes, reworks and cleanups.
Thanks to:
Aaro Koskinen, Alexandre Belloni, Alexey Kardashevskiy, Alistair Popple, Andy
Shevchenko, Aneesh Kumar K.V, Anshuman Khandual, Balbir Singh, Benjamin
Herrenschmidt, Christophe Leroy, Christophe Lombard, Cyril Bur, Daniel Axtens,
Dave Young, Finn Thain, Frederic Barrat, Gustavo Romero, Horia Geantă,
Jonathan Neuschäfer, Kees Cook, Larry Finger, Laurent Dufour, Laurent Vivier,
Logan Gunthorpe, Madhavan Srinivasan, Mark Greer, Mark Hairgrove, Markus
Elfring, Mathieu Malaterre, Matt Brown, Matt Evans, Mauricio Faria de
Oliveira, Michael Neuling, Naveen N. Rao, Nicholas Piggin, Paul Mackerras,
Philippe Bergheaud, Ram Pai, Rob Herring, Sam Bobroff, Segher Boessenkool,
Simon Guo, Simon Horman, Stewart Smith, Sukadev Bhattiprolu, Suraj Jitindar
Singh, Thiago Jung Bauermann, Vaibhav Jain, Vaidyanathan Srinivasan, Vasant
Hegde, Wei Yongjun.
-----BEGIN PGP SIGNATURE-----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=HAB1
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.17-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc updates from Michael Ellerman:
"Notable changes:
- Support for 4PB user address space on 64-bit, opt-in via mmap().
- Removal of POWER4 support, which was accidentally broken in 2016
and no one noticed, and blocked use of some modern instructions.
- Workarounds so that the hypervisor can enable Transactional Memory
on Power9.
- A series to disable the DAWR (Data Address Watchpoint Register) on
Power9.
- More information displayed in the meltdown/spectre_v1/v2 sysfs
files.
- A vpermxor (Power8 Altivec) implementation for the raid6 Q
Syndrome.
- A big series to make the allocation of our pacas (per cpu area),
kernel page tables, and per-cpu stacks NUMA aware when using the
Radix MMU on Power9.
And as usual many fixes, reworks and cleanups.
Thanks to: Aaro Koskinen, Alexandre Belloni, Alexey Kardashevskiy,
Alistair Popple, Andy Shevchenko, Aneesh Kumar K.V, Anshuman Khandual,
Balbir Singh, Benjamin Herrenschmidt, Christophe Leroy, Christophe
Lombard, Cyril Bur, Daniel Axtens, Dave Young, Finn Thain, Frederic
Barrat, Gustavo Romero, Horia Geantă, Jonathan Neuschäfer, Kees Cook,
Larry Finger, Laurent Dufour, Laurent Vivier, Logan Gunthorpe,
Madhavan Srinivasan, Mark Greer, Mark Hairgrove, Markus Elfring,
Mathieu Malaterre, Matt Brown, Matt Evans, Mauricio Faria de Oliveira,
Michael Neuling, Naveen N. Rao, Nicholas Piggin, Paul Mackerras,
Philippe Bergheaud, Ram Pai, Rob Herring, Sam Bobroff, Segher
Boessenkool, Simon Guo, Simon Horman, Stewart Smith, Sukadev
Bhattiprolu, Suraj Jitindar Singh, Thiago Jung Bauermann, Vaibhav
Jain, Vaidyanathan Srinivasan, Vasant Hegde, Wei Yongjun"
* tag 'powerpc-4.17-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (207 commits)
powerpc/64s/idle: Fix restore of AMOR on POWER9 after deep sleep
powerpc/64s: Fix POWER9 DD2.2 and above in cputable features
powerpc/64s: Fix pkey support in dt_cpu_ftrs, add CPU_FTR_PKEY bit
powerpc/64s: Fix dt_cpu_ftrs to have restore_cpu clear unwanted LPCR bits
Revert "powerpc/64s/idle: POWER9 ESL=0 stop avoid save/restore overhead"
powerpc: iomap.c: introduce io{read|write}64_{lo_hi|hi_lo}
powerpc: io.h: move iomap.h include so that it can use readq/writeq defs
cxl: Fix possible deadlock when processing page faults from cxllib
powerpc/hw_breakpoint: Only disable hw breakpoint if cpu supports it
powerpc/mm/radix: Update command line parsing for disable_radix
powerpc/mm/radix: Parse disable_radix commandline correctly.
powerpc/mm/hugetlb: initialize the pagetable cache correctly for hugetlb
powerpc/mm/radix: Update pte fragment count from 16 to 256 on radix
powerpc/mm/keys: Update documentation and remove unnecessary check
powerpc/64s/idle: POWER9 ESL=0 stop avoid save/restore overhead
powerpc/64s/idle: Consolidate power9_offline_stop()/power9_idle_stop()
powerpc/powernv: Always stop secondaries before reboot/shutdown
powerpc: hard disable irqs in smp_send_stop loop
powerpc: use NMI IPI for smp_send_stop
powerpc/powernv: Fix SMT4 forcing idle code
...
SLOF checks for 'sc 1' (hypercall) support by issuing a hcall with
H_SET_DABR. Since the recent commit e8ebedbf31 ("KVM: PPC: Book3S
HV: Return error from h_set_dabr() on POWER9") changed H_SET_DABR to
return H_UNSUPPORTED on Power9, we see guest boot failures, the
symptom is the boot seems to just stop in SLOF, eg:
SLOF ***************************************************************
QEMU Starting
Build Date = Sep 24 2017 12:23:07
FW Version = buildd@ release 20170724
<no further output>
SLOF can cope if H_SET_DABR returns H_HARDWARE. So wwitch the return
value to H_HARDWARE instead of H_UNSUPPORTED so that we don't break
the guest boot.
That does mean we return a different error to PowerVM in this case,
but that's probably not a big concern.
Fixes: e8ebedbf31 ("KVM: PPC: Book3S HV: Return error from h_set_dabr() on POWER9")
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Bring in yet another series that touches KVM code, and might need to
be merged into the kvm-ppc branch to resolve conflicts.
This required some changes in pnv_power9_force_smt4_catch/release()
due to the paca array becomming an array of pointers.
Jianping Liu