This is no longer needed when booted with device tree.
And let's replace cpu_is with soc_is for the PM code to
avoid confusion, they do the same thing.
Note that omap_pmic_late_init() now just calls
omap3_twl_init() and omap4_twl_init() to initialize the
voltage layer so we can remove the remaining references
to twl-common code and remove it in the following patch.
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now initialize I2C for mach-omap2 using device tree. And we
can move the remaining code in plat-omap/i2c.c into mach-omap1/i2c.c.
Note that we cannot remove some of the I2C bus reset functions
as they are being used by hwmod code.
Signed-off-by: Tony Lindgren <tony@atomide.com>
RTC is not available on DRA71x, so accessing any of the RTC
register or clkctrl register will lead to a crash. So, do not
register RTC hwmod for DRA71x.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
DRA71x processor family is a derivative of DRA722 ES2.0 targetted for
infotainment systems.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Hardware random number generator is present in both AM33xx and AM43xx
SoC's. So moving the hwmod data to common data.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
AM43xx SoC contains DES crypto hardware accelerator. Add hwmod data for
this IP so that it can be utilized by crypto frameworks.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Using HWSUP for l4sec clock domain is causing warnings in HWMOD code for
DRA7. Based on some observations, once the clock domain goes into an IDLE
state (because of no activity etc), the IDLEST for the module goes to '0x2'
value which means Interface IDLE condition. So far so go, however once the
MODULEMODE is set to disabled for the particular IP, the IDLEST for the
module should go to '0x3', per the HW AUTO IDLE protocol. However this is
not observed and there is no reason per the protocl for the transition to
not happen. This could potentially be a bug in the HW AUTO state-machine.
Work around for this is to use SWSUP only for the particular clockdomain.
With this all the transitions of IDLEST happen correctly and warnings
don't occur.
Signed-off-by: Joel Fernandes <joelf@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
DRA7 SoC contains hardware random number generator. Add hwmod data for
this IP so that it can be utilized.
Signed-off-by: Joel Fernandes <joelf@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
[t-kristo@ti.com: squashed the RNG hwmod IP flag fixes from Lokesh,
squashed the HS chip fix from Daniel Allred]
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
DRA7 SoC contains SHA crypto hardware accelerator. Add hwmod data for
this IP so that it can be utilized by crypto frameworks.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
DRA7 SoC contains AES crypto hardware accelerator. Add hwmod data for
this IP so that it can be utilized by crypto frameworks.
Signed-off-by: Joel Fernandes <joelf@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
[t-kristo@ti.com: squash in support for both AES1 and AES2 cores]
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
DRA7 SoC contains DES crypto hardware accelerator. Add hwmod data for
this IP so that it can be utilized by crypto frameworks.
Signed-off-by: Joel Fernandes <joelf@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
A single character (line break) should be put into a sequence.
Thus use the corresponding function "seq_putc".
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
A single character (line break) should be put into a sequence at the end.
Thus use the corresponding function "seq_putc".
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Strings which did not contain data format specification should be put into
a sequence. Thus use the corresponding function "seq_puts".
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Last user of this function was removed in commit
9b714 ("ARM: OMAP2+: Drop legacy board file for n900") during
legacy board file removal.
Signed-off-by: Nicolae Rosia <Nicolae_Rosia@mentor.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Last call of function was removed with commit
bfd46a ("ARM: OMAP: Fix i2c init for twl4030")
Signed-off-by: Nicolae Rosia <Nicolae_Rosia@mentor.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Last user of this function was removed in commit
e92fc4 ("ARM: OMAP2+: Drop legacy board file for LDP") during
legacy board file removal.
Signed-off-by: Nicolae Rosia <Nicolae_Rosia@mentor.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Last user of these functions was removed in commit
e92fc4 ("ARM: OMAP2+: Drop legacy board file for LDP") during
legacy board file removal.
Signed-off-by: Nicolae Rosia <Nicolae_Rosia@mentor.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Last user of these functions was deleted in commit
b42b91 ("ARM: OMAP2+: Remove board-omap4panda.c") during DT transition.
Signed-off-by: Nicolae Rosia <Nicolae_Rosia@mentor.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The function is empty, remove it.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add OMAP5 CPUIDLE support.
This patch adds MPUSS low power states in cpuidle.
C1 - CPU0 WFI + CPU1 WFI + MPU ON
C2 - CPU0 RET + CPU1 RET + MPU CSWR
Modified from TI kernel tree commit 605967fd2205 ("ARM: DRA7: PM:
cpuidle MPU CSWR support") except enable cpuidle for omap5 instead
of dra7.
According to Nishanth Menon <nm@ti.com>, cpuidle on dra7 is not
supported properly in the hardware so we don't want to enable it.
However, for omap5 this adds some nice power savings. Note that
the TI 3.8 based tree has other cpuidle states that we may be able
to enable later on.
On omap5-uevm, the power consumption eventually settles down to about
920mW with ehci-omap and ohci-omap3 unloaded compared to about 1.7W
without these patches. Note that it seems to take few minutes after
booting for the idle power to go down to 920mW from 1.3W, no idea so
far what might be causing that.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
[ j-keerthy@ti.com rework on 3.14]
Signed-off-by: Keerthy <j-keerthy@ti.com>
[nm@ti.com: updates based on profiling]
[tony@atomide.com: dropped CPUIDLE_FLAG_TIME_VALID no longer used,
changed for omap5 only as requested by Nishanth, updated comments]
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We don't want to fall through to a bunch of errors for retention
if PM_OMAP4_CPU_OSWR_DISABLE is not configured for a SoC.
Fixes: 6099dd37c6 ("ARM: OMAP5 / DRA7: Enable CPU RET on suspend")
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We need to properly initialize mpuss also on omap5 like we do on omap4.
Otherwise we run into similar kexec problems like we had on omap4 when
trying to kexec from a kernel with PM initialized.
Fixes: 0573b957fc ("ARM: OMAP4+: Prevent CPU1 related hang with kexec")
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
It's CONFIG_SOC_OMAP5, not CONFIG_ARCH_OMAP5. Looks like make randconfig
builds have not hit this one yet.
Fixes: b3bf289c1c ("ARM: OMAP2+: Fix build with CONFIG_SMP and CONFIG_PM
is not set")
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
For OMAP4, volt_data is set in omap44xx_voltagedomains_init.
If the SoC is neither OMAP443X or OMAP446X, we end up with a
NULL in volt_data which causes a kernel oops.
This is the case when booting OMAP4470.
Signed-off-by: Nicolae Rosia <Nicolae_Rosia@mentor.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
In the case where has_uart4 is false, en_uart4_mask and grpsel_uart4_mask
are not initialized and so any garbage value is being logically or'd into
the write of PM_WKEN and OMAP3430_PM_MPUGRPSEL. Fix this by initializing
these masks to zero.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
AM437x makes use of the omap_l3_noc driver so explicitly select
OMAP_INTERCONNECT in the Kconfig for SOC_AM43XX to ensure it gets enabled
for AM43XX only builds.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
With the printk cleanups merged into v4.9-rc1, we now get the omap
revision printed on multiple lines. Let's fix that and also remove the
extra empty space at the end of the features. And let's update things
to use scnprintf as suggested by Ivaylo Dimitrov
<ivo.g.dimitrov.75@gmail.com>.
Reported-by: Adam Ford <aford173@gmail.com>
Cc: Ivaylo Dimitrov <ivo.g.dimitrov.75@gmail.com>
Reviewed-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The cleanups for v4.9 are a little larger that usual, but thankfully
that is almost exclusively due to removing a significant number of
files that have become obsolete after the still ongoing conversion
of old board files to devicetree.
- for mach-omap2, which is still the largest platform in arch/arm/,
the conversion to DT is finally complete after the Nokia N900 is
now fully supported there, along with the omap3 LDP, and we can
remove those two board files.
If no regressions are found, another large cleanup for the platform
will happen as a follow-up, removing dead code and restructuring
the platform based on being DT-only.
- In mach-imx, similar work is ongoing, but has not come that far.
This time, we remove the obsolete board file for the i.MX1
generation, which like i.MX25, i.MX5, i.MX6, and i.MX7 is now DT-only.
The remaining board files are for i.MX2 and i.MX3 machines
based on old ARM926 or ARM1136 cores that should work with DT
in principle.
- realview has just been converted from board files to DT, and a lot
of code gets removed in the process. This is the last
ARM/Keil/Versatile derived platform that was still using board
files, the other ones being integrator, versatile and vexpress.
We can probably merge the remaining code into a single directory
in the near future.
- clps711x had completed the conversion in v4.8, but we accidentally
left the files in place that should have been deleted then.
Conflicts: two files deleted here have been modified upstream,
the changes can be discarded.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=WaLy
-----END PGP SIGNATURE-----
Merge tag 'armsoc-cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC cleanups from Arnd Bergmann:
"The cleanups for v4.9 are a little larger that usual, but thankfully
that is almost exclusively due to removing a significant number of
files that have become obsolete after the still ongoing conversion of
old board files to devicetree.
- for mach-omap2, which is still the largest platform in arch/arm/,
the conversion to DT is finally complete after the Nokia N900 is
now fully supported there, along with the omap3 LDP, and we can
remove those two board files. If no regressions are found, another
large cleanup for the platform will happen as a follow-up, removing
dead code and restructuring the platform based on being DT-only.
- In mach-imx, similar work is ongoing, but has not come that far.
This time, we remove the obsolete board file for the i.MX1
generation, which like i.MX25, i.MX5, i.MX6, and i.MX7 is now
DT-only. The remaining board files are for i.MX2 and i.MX3 machines
based on old ARM926 or ARM1136 cores that should work with DT in
principle.
- realview has just been converted from board files to DT, and a lot
of code gets removed in the process. This is the last
ARM/Keil/Versatile derived platform that was still using board
files, the other ones being integrator, versatile and vexpress. We
can probably merge the remaining code into a single directory in
the near future.
- clps711x had completed the conversion in v4.8, but we accidentally
left the files in place that should have been deleted then"
* tag 'armsoc-cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (21 commits)
ARM: select PCI_DOMAINS config from ARCH_MULTIPLATFORM
ARM: stop *MIGHT_HAVE_PCI* config from being selected redundantly
ARM: imx: (trivial) fix typo and grammar
ARM: clps711x: remove extraneous files
ARM: imx: use IS_ENABLED() instead of checking for built-in or module
ARM: OMAP2+: use IS_ENABLED() instead of checking for built-in or module
ARM: OMAP1: use IS_ENABLED() instead of checking for built-in or module
ARM: imx: remove platform-mxc_rnga
ARM: realview: imply device tree boot
ARM: realview: no need to select SMP_ON_UP explicitly
ARM: realview: delete the RealView board files
ARM: imx: no need to select SMP_ON_UP explicitly
ARM: i.MX: Move SOC_IMX1 into 'Device tree only'
ARM: i.MX: Remove i.MX1 non-DT support
ARM: i.MX: Remove i.MX1 Synertronixx SCB9328 board support
ARM: i.MX: Remove i.MX1 Armadeus APF9328 board support
ARM: mxs: remove obsolete startup code for TX28
ARM: i.MX31 iomux: remove duplicates with alternate name
ARM: i.MX31 iomux: remove plain duplicates
ARM: OMAP2+: Drop legacy board file for LDP
...
Subsystem improvements:
- Do away with the last users of the obsolete Kconfig options
ARCH_REQUIRE_GPIOLIB and ARCH_WANT_OPTIONAL_GPIOLIB (the latter
always sounded like an item on a wishlist to Santa Claus to
me). We can now select GPIOLIB and be done with it, for all
archs. After some struggle it even work on UM. Not that it has
GPIO, but if it wants to, it can select the library.
- Continued efforts to make drivers properly either tristate or
bool.
- Introduce a warning for drivers assigning default triggers to
their irqchip lines when probed from device tree, so we find and
fix these ambigous drivers. It is agreed that in the OF config
path, the device tree defines trigger characteristics.
- The same warning, mutatis mutandis, for ACPI-probed GPIO
irqchips.
- We introduce the ability to mark certain IRQ lines as "unusable"
as they can be taken by BIOS/firmware, unrouted in silicon and
generally nasty if you use them, and such things. This is
put to good use in the STMPE driver and also in the Cherryview
pin control driver.
- A new "mockup" virtual GPIO device that can be used for testing.
The plan is to add unit tests under tools/* for exercising this
device and verify that the kernel code paths are working as they
should.
- Make memory-mapped I/O-drivers depend on HAS_IOMEM. This was
implicit all the time, but when people started building UM
with allyesconfig or allmodconfig it exploded in their face.
- Move some stray bits of device tree and ACPI HW description
callbacks down into their respective implementation silo. These
were causing issues when compiling on !HAS_IOMEM as well, so
now eventually UM compiles the GPIOLIB library if it wants to.
New drivers:
- New driver for the Aspeed GPIO front-end companion to the
pin controller merged through the pin control tree.
- New driver for the LP873x PMIC GPIO portions.
- New driver for Technologic Systems' I2C FPGA GPIO such as
TS4900, TS-7970, TS-7990 and TS-4100.
- New driver for the Broadcom BCM63xx series including BCM6338
and BCM6345.
- New driver for the Intel WhiskeyCove PMIC GPIO.
- New driver for the Allwinner AXP209 PMIC GPIO portions.
- New driver for Diamond Systems 48 line GPIO-MM, another of
these port-mapped I/O expansion cards.
- Support the STMicroelectronics STMPE1600 variant in the STMPE
driver.
Driver improvements:
- The STMPE driver now supports rising/falling edge detection
properly for IRQs.
- The PCA954x will now fetch and enable its VCC regulator properly.
- Major rework of the PCA953x driver with the goal of eventually
switching it over to use regmap and thus modernize it even more.
- Switch the IOP driver to use the generic MMIO GPIO library.
- Move the ages old HTC EGPIO (extended GPIO) GPIO expander driver
over to this subsystem from MFD, achieveing some separation of
concerns.
-----BEGIN PGP SIGNATURE-----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=ABbi
-----END PGP SIGNATURE-----
Merge tag 'gpio-v4.9-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"This is the bulk of GPIO changes for the v4.9 series:
Subsystem improvements:
- do away with the last users of the obsolete Kconfig options
ARCH_REQUIRE_GPIOLIB and ARCH_WANT_OPTIONAL_GPIOLIB (the latter
always sounded like an item on a wishlist to Santa Claus to me). We
can now select GPIOLIB and be done with it, for all archs. After
some struggle it even work on UM. Not that it has GPIO, but if it
wants to, it can select the library.
- continued efforts to make drivers properly either tristate or bool.
- introduce a warning for drivers assigning default triggers to their
irqchip lines when probed from device tree, so we find and fix
these ambigous drivers. It is agreed that in the OF config path,
the device tree defines trigger characteristics.
- the same warning, mutatis mutandis, for ACPI-probed GPIO irqchips.
- we introduce the ability to mark certain IRQ lines as "unusable" as
they can be taken by BIOS/firmware, unrouted in silicon and
generally nasty if you use them, and such things. This is put to
good use in the STMPE driver and also in the Cherryview pin control
driver.
- a new "mockup" virtual GPIO device that can be used for testing.
The plan is to add unit tests under tools/* for exercising this
device and verify that the kernel code paths are working as they
should.
- make memory-mapped I/O-drivers depend on HAS_IOMEM. This was
implicit all the time, but when people started building UM with
allyesconfig or allmodconfig it exploded in their face.
- move some stray bits of device tree and ACPI HW description
callbacks down into their respective implementation silo. These
were causing issues when compiling on !HAS_IOMEM as well, so now
eventually UM compiles the GPIOLIB library if it wants to.
New drivers:
- new driver for the Aspeed GPIO front-end companion to the pin
controller merged through the pin control tree.
- new driver for the LP873x PMIC GPIO portions.
- new driver for Technologic Systems' I2C FPGA GPIO such as TS4900,
TS-7970, TS-7990 and TS-4100.
- new driver for the Broadcom BCM63xx series including BCM6338 and
BCM6345.
- new driver for the Intel WhiskeyCove PMIC GPIO.
- new driver for the Allwinner AXP209 PMIC GPIO portions.
- new driver for Diamond Systems 48 line GPIO-MM, another of these
port-mapped I/O expansion cards.
- support the STMicroelectronics STMPE1600 variant in the STMPE
driver.
Driver improvements:
- the STMPE driver now supports rising/falling edge detection
properly for IRQs.
- the PCA954x will now fetch and enable its VCC regulator properly.
- major rework of the PCA953x driver with the goal of eventually
switching it over to use regmap and thus modernize it even more.
- switch the IOP driver to use the generic MMIO GPIO library.
- move the ages old HTC EGPIO (extended GPIO) GPIO expander driver
over to this subsystem from MFD, achieveing some separation of
concerns"
* tag 'gpio-v4.9-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (81 commits)
gpio: add missing static inline
gpio: OF: localize some gpiochip init functions
gpio: acpi: separation of concerns
gpio: OF: separation of concerns
gpio: make memory-mapped drivers depend on HAS_IOMEM
gpio: stmpe: use BIT() macro
gpio: stmpe: forbid unused lines to be mapped as IRQs
mfd/gpio: Move HTC GPIO driver to GPIO subsystem
gpio: MAINTAINERS: Add an entry for GPIO mockup driver
gpio/mockup: add virtual gpio device
gpio: Added zynq specific check for special pins on bank zero
gpio: axp209: Implement get_direction
gpio: aspeed: remove redundant return value check
gpio: loongson1: remove redundant return value check
ARM: omap2: fix missing include
gpio: tc3589x: fix up complaints on unsigned
gpio: tc3589x: add .get_direction() and small cleanup
gpio: f7188x: use gpiochip_get_data instead of container_of
gpio: tps65218: use devm_gpiochip_add_data() for gpio registration
gpio: aspeed: fix return value check in aspeed_gpio_probe()
...
Pull CPU hotplug updates from Thomas Gleixner:
"Yet another batch of cpu hotplug core updates and conversions:
- Provide core infrastructure for multi instance drivers so the
drivers do not have to keep custom lists.
- Convert custom lists to the new infrastructure. The block-mq custom
list conversion comes through the block tree and makes the diffstat
tip over to more lines removed than added.
- Handle unbalanced hotplug enable/disable calls more gracefully.
- Remove the obsolete CPU_STARTING/DYING notifier support.
- Convert another batch of notifier users.
The relayfs changes which conflicted with the conversion have been
shipped to me by Andrew.
The remaining lot is targeted for 4.10 so that we finally can remove
the rest of the notifiers"
* 'smp-hotplug-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (46 commits)
cpufreq: Fix up conversion to hotplug state machine
blk/mq: Reserve hotplug states for block multiqueue
x86/apic/uv: Convert to hotplug state machine
s390/mm/pfault: Convert to hotplug state machine
mips/loongson/smp: Convert to hotplug state machine
mips/octeon/smp: Convert to hotplug state machine
fault-injection/cpu: Convert to hotplug state machine
padata: Convert to hotplug state machine
cpufreq: Convert to hotplug state machine
ACPI/processor: Convert to hotplug state machine
virtio scsi: Convert to hotplug state machine
oprofile/timer: Convert to hotplug state machine
block/softirq: Convert to hotplug state machine
lib/irq_poll: Convert to hotplug state machine
x86/microcode: Convert to hotplug state machine
sh/SH-X3 SMP: Convert to hotplug state machine
ia64/mca: Convert to hotplug state machine
ARM/OMAP/wakeupgen: Convert to hotplug state machine
ARM/shmobile: Convert to hotplug state machine
arm64/FP/SIMD: Convert to hotplug state machine
...
commit d47529b2e9
"gpio: don't include module.h in shared driver header"
removed <linux/module.h> from the <linux/gpio/driver.h> header.
It seems arch/arm/mach-omap2/board-rx51-peripherals.c
is using __initdata_or_module from <linux/module.h> through
<linux/gpio.h> to <linux/gpio/driver.h>, so break this dependency
so that we get a clean compile.
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: Tony Lindgren <tony@atomide.com>
Fixes: d47529b2e9 ("gpio: don't include module.h in shared driver header")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
to update mach-omap1 and mach-oamp2 to use IS_ENABLED macro.
-----BEGIN PGP SIGNATURE-----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=0xjC
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.9/soc-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/cleanup
Merge "omap soc updates for v4.9 merge window" from Tony Lindgren:
Two patches from Javier Martinez Canillas <javier@osg.samsung.com>
to update mach-omap1 and mach-oamp2 to use IS_ENABLED macro.
* tag 'omap-for-v4.9/soc-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: use IS_ENABLED() instead of checking for built-in or module
ARM: OMAP1: use IS_ENABLED() instead of checking for built-in or module
booting for v4.8 to allow making mach-omap2 device tree only for
v4.9.
We've had Nokia N900 and omap3 LDP board-*.c files remaining
while other omap3 devices have been device tree only for quite
a while now. Also N900 and LDP have had device tree based booting
working for years now, but few drivers for N900 were still only
working in legacy only mode until recently. With the remaining
issues out of the way, we discussed on the mailing lists that
we're finally OK to remove the remaining board-*.c files.
For the timing of this pull request, I wanted to wait until
v4.8-rc1 is out to make sure the legacy booting still works fine
after the merge window before doing it.
And for v4.8, let's not touch any other platform data in case we
still need to revert for some reason. This makes the revert just a
question of adding back the legacy board-*.c files.
Then if no issues, we can remove the unused remaining platform
data later on for v4.9.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=AUHa
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.8/legacy-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/cleanup
Merge "drop last omap3 board files for v4.8" from Tony Lindgren:
Remove the last two legacy board-*.c files for omap3 for legacy
booting for v4.8 to allow making mach-omap2 device tree only for
v4.9.
We've had Nokia N900 and omap3 LDP board-*.c files remaining
while other omap3 devices have been device tree only for quite
a while now. Also N900 and LDP have had device tree based booting
working for years now, but few drivers for N900 were still only
working in legacy only mode until recently. With the remaining
issues out of the way, we discussed on the mailing lists that
we're finally OK to remove the remaining board-*.c files.
For the timing of this pull request, I wanted to wait until
v4.8-rc1 is out to make sure the legacy booting still works fine
after the merge window before doing it.
And for v4.8, let's not touch any other platform data in case we
still need to revert for some reason. This makes the revert just a
question of adding back the legacy board-*.c files.
Then if no issues, we can remove the unused remaining platform
data later on for v4.9.
* tag 'omap-for-v4.8/legacy-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: Drop legacy board file for LDP
ARM: OMAP2+: Drop legacy board file for n900
The IS_ENABLED() macro checks if a Kconfig symbol has been enabled either
built-in or as a module, use that macro instead of open coding the same.
Using the macro makes the code more readable by helping abstract away some
of the Kconfig built-in and module enable details.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Driver updates for ARM SoCs.
A slew of changes this release cycle. The reset driver tree, that we merge
through arm-soc for historical reasons, is also sizable this time around.
Among the changes:
- clps711x: Treewide changes to compatible strings, merged here for simplicity.
- Qualcomm: SCM firmware driver cleanups, move to platform driver
- ux500: Major cleanups, removal of old mach-specific infrastructure.
- Atmel external bus memory driver
- Move of brcmstb platform to the rest of bcm
- PMC driver updates for tegra, various fixes and improvements
- Samsung platform driver updates to support 64-bit Exynos platforms
- Reset controller cleanups moving to devm_reset_controller_register() APIs
- Reset controller driver for Amlogic Meson
- Reset controller driver for Hisilicon hi6220
- ARM SCPI power domain support
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=O8+y
-----END PGP SIGNATURE-----
Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver updates from Olof Johansson:
"Driver updates for ARM SoCs.
A slew of changes this release cycle. The reset driver tree, that we
merge through arm-soc for historical reasons, is also sizable this
time around.
Among the changes:
- clps711x: Treewide changes to compatible strings, merged here for simplicity.
- Qualcomm: SCM firmware driver cleanups, move to platform driver
- ux500: Major cleanups, removal of old mach-specific infrastructure.
- Atmel external bus memory driver
- Move of brcmstb platform to the rest of bcm
- PMC driver updates for tegra, various fixes and improvements
- Samsung platform driver updates to support 64-bit Exynos platforms
- Reset controller cleanups moving to devm_reset_controller_register() APIs
- Reset controller driver for Amlogic Meson
- Reset controller driver for Hisilicon hi6220
- ARM SCPI power domain support"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (100 commits)
ARM: ux500: consolidate base platform files
ARM: ux500: move soc_id driver to drivers/soc
ARM: ux500: call ux500_setup_id later
ARM: ux500: consolidate soc_device code in id.c
ARM: ux500: remove cpu_is_u* helpers
ARM: ux500: use CLK_OF_DECLARE()
ARM: ux500: move l2x0 init to .init_irq
mfd: db8500 stop passing around platform data
ASoC: ab8500-codec: remove platform data based probe
ARM: ux500: move ab8500_regulator_plat_data into driver
ARM: ux500: remove unused regulator data
soc: raspberrypi-power: add CONFIG_OF dependency
firmware: scpi: add CONFIG_OF dependency
video: clps711x-fb: Changing the compatibility string to match with the smallest supported chip
input: clps711x-keypad: Changing the compatibility string to match with the smallest supported chip
pwm: clps711x: Changing the compatibility string to match with the smallest supported chip
serial: clps711x: Changing the compatibility string to match with the smallest supported chip
irqchip: clps711x: Changing the compatibility string to match with the smallest supported chip
clocksource: clps711x: Changing the compatibility string to match with the smallest supported chip
clk: clps711x: Changing the compatibility string to match with the smallest supported chip
...
The cleanup branch keeps going down in size as we've completed a lot of
the major legacy platform removals and conversions.
A handful of changes this time around, some of the themes or larger sets are:
- A bunch of i.MX cleanups around platform detection, init call cleanups
- Misc fixes of missing/implicit includes
- Removal of ARCH_[WANT_OPTIONAL|REQUIRE]_GPIOLIB
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=SfR/
-----END PGP SIGNATURE-----
Merge tag 'armsoc-cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC cleanups from Olof Johansson:
"The cleanup branch keeps going down in size as we've completed a lot
of the major legacy platform removals and conversions.
A handful of changes this time around, some of the themes or larger
sets are:
- A bunch of i.MX cleanups around platform detection, init call cleanups
- Misc fixes of missing/implicit includes
- Removal of ARCH_[WANT_OPTIONAL|REQUIRE]_GPIOLIB"
* tag 'armsoc-cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (40 commits)
ARM: mps2: fix typo
ARM: s3c64xx: avoid warning about 'struct device_node'
bus: mvebu-mbus: make mvebu_mbus_syscore_ops static
bus: mvebu-mbus: fix __iomem on register pointers
ARM: tegra: Remove board_init_funcs array
ARM: iop: Fix indentation
ARM: imx: remove cpu_is_mx*()
ARM: imx: remove last call to cpu_is_mx5*
ARM: imx: rework mx27_pm_init() call
ARM: imx: deconstruct mx3_idle
ARM: imx: deconstruct mxc_rnga initialization
ARM: imx: remove cpu_is_mx1 check
ARM: i.MX: Do not explicitly call l2x0_of_init()
ARM: i.MX: system.c: Tweak prefetch settings for performance
ARM: i.MX: system.c: Replace magic numbers
ARM: i.MX: system.c: Remove redundant errata 752271 code
ARM: i.MX: system.c: Convert goto to if statement
ARM: Kirkwood: fix kirkwood_pm_init() declaration/type
ARM: Kirkwood: make kirkwood_disable_mbus_error_propagation() static
ARM: orion5x: make orion5x_legacy_handle_irq static
...
Now that we have moved the check for valid clkctrl_offs to the caller of
am33xx_cm_wait_module_ready/idle and omap4_cminst_wait_module_ready/idle
let's remove the now redundant check for clkctrl_offs from these functions.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Acked-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Previously the low-level CM call internal to the
_omap4_wait_target_ready/disable calls was responsible for checking for
a valid clkctrl_offs. Now we must also consider the value of the
prcm.omap4.flags because if HWMOD_OMAP4_ZERO_CLKCTRL_OFFSET is set in
the flags then clkctrl_offs of 0 is valid.
Let's add this check into the _omap4_wait_target_ready/disable where we
have access to both the clkctrl_offs and the flags values and simply
return 0 without calling the low level CM call at all, which would have
returned 0 anyway if the clktrl_offs was zero.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Acked-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The RTC hwmod on AM335x family of SoCs is unique in that the
clkctrl_offs in the PRCM is 0. We rely on a clkctrl_offs of zero as
indicating no clkctrl is present so we must flag this hwmod with
HWMOD_OMAP4_ZERO_CLKCTRL_OFFSET to indicate the 0 clkctrl_offs is in
fact valid in this case.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Acked-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Nearly all modules on OMAP4 and newer platforms have clkctrl offsets
that are non-zero except for the RTC on am335x. Because we rely on a
clkctrl_offset of zero to indicate no clkctrl_offset being present,
lets add a HWMOD_OMAP4_ZERO_CLKCTRL_OFFSET flag to use to indicate
hwmods that have a valid clkctrl_offset of 0.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Acked-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add missing sysconfig/sysstatus information
to OMAP3 hwmod. The information has been
checked against OMAP34xx and OMAP36xx TRM.
Without this change DSI block is not reset
during boot, which is required for working
Nokia N950 display.
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Cc: stable@vger.kernel.org
Signed-off-by: Tony Lindgren <tony@atomide.com>
Let's drop the last two remaining omap3 legacy boot board files.
Let's only use the device tree based booting known to work for
these two boards.
We still have two omap3 boards booting in legacy mode in addition
to device tree based booting. All the other ten or so omap2+ SoCs
have been booting using device tree mode only for years now. This
has allowed us to get rid of quite a bit of arch/arm/mach-omap2
related platform init code in favor of dts and driver changes.
Pretty much the only remaining known users for omap3 legacy boot
board files are Kevin's and Russell's boot test systems, and N900
kernel tree maintained by Pali and Ivaylo. And all of them are
also supporting the device tree based booting. The legacy booting
mode has been kept around mostly to verify against regressions.
As there is still a slim chance of possible other uses of the
mainline kernel for these boards, let's just drop the board
files for v4.8, and let's not touch the related platform init
code until around v4.9 time if no issues are found. This makes
it trivial for us to add back the board files with a simple revert.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Let's drop the last two remaining omap3 legacy boot board files.
Let's only use the device tree based booting known to work for
these two boards.
We still have two omap3 boards booting in legacy mode in addition
to device tree based booting. All the other ten or so omap2+ SoCs
have been booting using device tree mode only for years now. This
has allowed us to get rid of quite a bit of arch/arm/mach-omap2
related platform init code in favor of dts and driver changes.
Pretty much the only remaining known users for omap3 legacy boot
board files are Kevin's and Russell's boot test systems, and N900
kernel tree maintained by Pali and Ivaylo. And all of them are
also supporting the device tree based booting. The legacy booting
mode has been kept around mostly to verify against regressions.
As there is still a slim chance of possible other uses of the
mainline kernel for these boards, let's just drop the board
files for v4.8, and let's not touch the related platform init
code until around v4.9 time if no issues are found. This makes
it trivial for us to add back the board files with a simple revert.
Acked-By: Sebastian Reichel <sre@kernel.org>
Acked-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Acked-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
- Fix a make randconfig build error for recent SMP kexec changes
- A series of clock related fixes to prepare things for moving
device clkctrl register handling to drivers/clk
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=qmem
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.8/soc-pt2-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/soc
Merge "Few more omap SoC changes for v4.8 merge window" from Tony Lindgren:
- Fix a make randconfig build error for recent SMP kexec changes
- A series of clock related fixes to prepare things for moving
device clkctrl register handling to drivers/clk
* tag 'omap-for-v4.8/soc-pt2-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: AM33xx: fix module_wait_ready without clkctrl register
ARM: OMAP2+: clockdomain: add usecounting support to autoidle APIs
ARM: OMAP2+: timer: change order of hwmod data handling
ARM: OMAP2+: hwmod: fetch main_clk based on hwmod name
ARM: OMAP2+: omap_device: create clock alias purely from DT data
ARM: OMAP2+: Fix build with CONFIG_SMP and CONFIG_PM is not set
* commit '5c34a4e89c743339f78cafb2f2a826a010f0746a':
ARM: do away with ARCH_[WANT_OPTIONAL|REQUIRE]_GPIOLIB
ARM: uniphier: drop code for old DT binding
These cause a harmless conflict with the clps711x multiplatform
support, and it's easy to resolve.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
If the module has no clkctrl register defined, module_wait_ready should
not try to access this. This can potentially cause an illegal register
access, and result in bad idle reporting also.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The previous implementation was racy in many locations, where the current
status of the clockdomain was read out, some operations were executed,
and the previous status info was used afterwards to decide next state
for the clockdomain. Instead, fix the implementation of the allow_idle /
deny_idle APIs to properly have usecounting support. This allows clean
handling internally within the clockdomain core, and simplifies the
usage also within hwmod.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
With the introduction of hwmod module clocks, the name of the hwmod
main clk may not be available before hwmod setup, as hwmod setup
may lookup the main clock dynamically based on the hwmod name.
Thus, change the order of hwmod setup and main clock handling for
the timer code, to make sure the main clock is going to be
available.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
With the transition to hwmod module clocks, all hwmods will have
their main clocks named <hwmod_name>_mod_ck. Use this info to
fetch main_clk, and use it if found.
Also, if a main_clk is found based on the hwmod name, disable
the direct PRCM modulemode access from hwmod.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This avoids the need to add most of the clock aliases under
drivers/clk/ti/clk-xyz.c files.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
I found one more make randconfig build error with the recent
SMP kexec changes. We need the mpuss now always available early.
Fixes: 0573b957fc ("ARM: OMAP4+: Prevent CPU1 related hang
with kexec")
Signed-off-by: Tony Lindgren <tony@atomide.com>
Drop dmtimer usage for pulse timer in favor of hrtimer. That allows
removing PWM dmitimer platform data usage.
Signed-off-by: Ivaylo Dimitrov <ivo.g.dimitrov.75@gmail.com>
Acked-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
With the upcoming removal of legacy boot, lets add support to one of the
last N900 drivers remaining without it. As the driver still uses omap
dmtimer, add auxdata as well.
Signed-off-by: Ivaylo Dimitrov <ivo.g.dimitrov.75@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Convert driver to use PWM framework instead of calling dmtimer functions
directly for PWM timer. Remove paragraph about writing to the Free Software
Foundation's mailing address while at it.
Signed-off-by: Ivaylo Dimitrov <ivo.g.dimitrov.75@gmail.com>
Acked-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Looks like I only partially fixed up things if CONFIG_SMP
is not set for the recent kexec changes. We don't have
boot_secondary available without SMP as reported by Arnd.
Fixes: 0573b957fc ("ARM: OMAP4+: Prevent CPU1 related hang with kexec")
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We need to reset CPU1 properly for kexec when booting different
kernel versions. Otherwise CPU1 will attempt to boot the the
previous kernel's start_secondary(). Note that the restctrl
register is different from the low-power mode wakeup register
CPU1_WAKEUP_NS_PA_ADDR. We need to configure both.
Let's fix the issue by defining SoC specific data to initialize
things in a more generic way. And let's also standardize omap-smp.c
to use soc_is instead of cpu_is while at it.
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
Tested-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Kexec booted kernels on omap4 will hang early during the boot if the
booted kernel is different version from the previous kernel.
This is because the previous kernel may have configured low-power mode
using CPU1_WAKEUP_NS_PA_ADDR. In that case it points to the previous
kernel's omap4_secondary_startup(), and CPU1 can be in low power mode
from the previous kernel. When the new kernel configures the CPU1
clockdomain, CPU1 can wake from low power state prematurely during
omap44xx_clockdomains_init() running random code.
Let's fix the issue by configuring CPU1_WAKEUP_NS_PA_ADDR before we
call omap44xx_clockdomains_init(). Note that this is very early during
the init, and we will do proper CPU1 reset during SMP init a bit later
on in omap4_smp_prepare_cpus(). And we need to do this when SMP is
not enabled as the previous kernel may have had it enabled.
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
Tested-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Prepare things for making kexec work on SMP omap variants by initializing
SARM RAM base early. This allows us to configure CPU1 for kexec in case
the previous kernel has put CPU1 in low power mode.
Note that this should not prevent moving other SAR RAM code to live
under drivers. However for kexec, we will need this very early.
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
Tested-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
As per the TRM: http://www.ti.com/lit/ug/spruh73m/spruh73m.pdf
offset 0x4 is reserved for PRM_PER. Hence removing the wrongly
defined address offset.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The ti81xx_rtc_hwmod is not exported, or declared outside the file
arch/arm/mach-omap2/omap_hwmod_81xx_data.c so make it static to
avoid the following warning:
arch/arm/mach-omap2/omap_hwmod_81xx_data.c:246:19: warning: symbol 'ti81xx_rtc_hwmod' was not declared. Should it be static?
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
pruss hwmod RSTST register wrongly points to PWRSTCTRL register in case of
am43xx. Fix the RSTST register offset value.
This can lead to setting of wrong power state values for PER domain.
Fixes: 1c7e224d ("ARM: OMAP2+: hwmod: AM335x: runtime register update")
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
- Fix dra7 for hardware issues limiting L4Per and L3init power domains
to on state. Without this the devices may not work correctly after
some time of use because of asymmetric aging. And related to this,
let's also remove the unusable states.
- Always select omap interconnect for am43x as otherwise the am43x
only configurations will not boot properly. This can happen easily
for any product kernels that leave out other SoCs to save memory.
- Fix DSS PLL2 addresses that have gone unused for now
- Select erratum 430973 for omap3, this is now safe to do and can
save quite a bit of debugging time for people who may have left
it out.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=mQyc
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.7/fixes-powedomain' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Fixes for omaps for v4.7-rc cycle:
- Fix dra7 for hardware issues limiting L4Per and L3init power domains
to on state. Without this the devices may not work correctly after
some time of use because of asymmetric aging. And related to this,
let's also remove the unusable states.
- Always select omap interconnect for am43x as otherwise the am43x
only configurations will not boot properly. This can happen easily
for any product kernels that leave out other SoCs to save memory.
- Fix DSS PLL2 addresses that have gone unused for now
- Select erratum 430973 for omap3, this is now safe to do and can
save quite a bit of debugging time for people who may have left
it out.
* tag 'omap-for-v4.7/fixes-powedomain' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP: DRA7: powerdomain data: Remove unused pwrsts_mem_ret
ARM: OMAP: DRA7: powerdomain data: Remove unused pwrsts_logic_ret
ARM: OMAP: DRA7: powerdomain data: Set L3init and L4per to ON
ARM: OMAP2+: Select OMAP_INTERCONNECT for SOC_AM43XX
ARM: dts: DRA74x: fix DSS PLL2 addresses
ARM: OMAP2: Enable Errata 430973 for OMAP3
+ Linux 4.7-rc2
Signed-off-by: Olof Johansson <olof@lixom.net>
- Two boot warning fixes from the RCU tree that should have gotten
merged several weeks ago already but did not because of issues
with who merges them. Paul has now split the RCU warning fixes into
sets for various maintainers.
- Fix ams-delta FIQ regression caused by omap1 sparse IRQ changes
- Fix PM for omap3 boards using timer12 and gptimer, like the
original beagleboard
- Fix hangs on am437x-sk-evm by lowering the I2C bus speed
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=P0Vi
-----END PGP SIGNATURE-----
Merge tag 'fixes-rcu-fiq-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Fixes for omaps for v4.7-rc cycle:
- Two boot warning fixes from the RCU tree that should have gotten
merged several weeks ago already but did not because of issues
with who merges them. Paul has now split the RCU warning fixes into
sets for various maintainers.
- Fix ams-delta FIQ regression caused by omap1 sparse IRQ changes
- Fix PM for omap3 boards using timer12 and gptimer, like the
original beagleboard
- Fix hangs on am437x-sk-evm by lowering the I2C bus speed
* tag 'fixes-rcu-fiq-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: am437x-sk-evm: Reduce i2c0 bus speed for tps65218
ARM: OMAP2+: timer: add probe for clocksources
ARM: OMAP1: fix ams-delta FIQ handler to work with sparse IRQ
arm: Use _rcuidle for smp_cross_call() tracepoints
arm: Use _rcuidle tracepoint to allow use from idle
Signed-off-by: Olof Johansson <olof@lixom.net>
A few platforms are currently missing clocksource_probe() completely
in their time_init functionality. On OMAP3430 for example, this is
causing cpuidle to be pretty much dead, as the counter32k is not
going to be registered and instead a gptimer is used as a clocksource.
This will tick in periodic mode, preventing any deeper idle states.
While here, also drop one unnecessary check for populated DT before
existing clocksource_probe() call.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
As per the latest revision F of public TRM for DRA7/AM57xx SoCs
SPRUHZ6F[1] (April 2016), with the exception of MPU power domain, all
other power domains do not have memories capable of retention since
they all operate in either "ON" or "OFF" mode. For these power states,
the retention state for memories are basically ignored by PRCM and does
not require to be programmed.
[1] http://www.ti.com/lit/pdf/spruhz6
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
As per the latest revision F of public TRM for DRA7/AM57xx SoCs
SPRUHZ6F[1] (April 2016), with the exception of MPU power domain (and
CPUx sub power domains), all other power domains can either operate
in "ON" mode OR in some cases, "OFF" mode. For these power states,
the logic retention state is basically ignored by PRCM and does not
require to be programmed.
[1] http://www.ti.com/lit/pdf/spruhz6
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
As per the latest revision F of public TRM for DRA7/AM57xx SoCs
SPRUHZ6F[1] (April 2016), L4Per and L3init power domains now operate in
always "ON" mode due to asymmetric aging limitations. Update the same
[1] http://www.ti.com/lit/pdf/spruhz6
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The addresses for DSS are provided in the DT data, so they can be
removed from the hwmod.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
QSPI address space information is passed from device tree. Therefore
remove legacy way of passing address space via hwmod data.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The new pdata callback (force_ick_on) is now used by the driver and the old
callback related code can be removed.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
McBSP2/3 module's sidetone module operates using the module's ICLK clock.
When the Sidetone is in use the interface clock of the module must not
idle. To prevent the iclk idling the driver expects to have pdata callback
to call. With this patch the callback is going to be set up for DT boot
also.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
McBSP2/3 module's sidetone module operates using the module's ICLK clock.
When the Sidetone is in use the interface clock of the module must not
idle. The new callback expects to receive the *clk of the module's ick and
not the id number of the McBSP. This will allow us more cleanups and going
to simplify the ICLK handling.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The McBSPLP's sidetone main clock is the McBSPLP's ICLK, not FCLK as the
sidetone only receives the ICLK from the main McBSP module.
Since the McBSP and sidetone is using the very same clock from PRCM level
the sidetone must not have the prcm section to check the clock status since
the sidetone is only used when McBSP is already configured.
If two separate hwmods looking at the same bit and they would use
pm_runtime in nested way (as it must happen with McBSP and it's ST module)
the hwmod would warn, because the idlest will not match what it is expected
after enable/disable of the clocks.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Devices that utilize the OCP registers and/or PRCM registers and
register bit fields should be modeled using hwmod. Since eQEP, ePWM and
eCAP don't fall under this category, remove their hwmod entries.
Instead these clocks simply use the clock that is passed through by its
parent PWMSS. Therefore, PWMSS handles the clock for itself and its
subdevices.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
AM43XX SoCs make use of the omap_l3_noc driver so explicitly select
OMAP_INTERCONNECT in the Kconfig for SOC_AM43XX to ensure it always gets
enabled for AM43XX only builds.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Enable Erratum 430973 similar to commit 5c86c5339c ("ARM:
omap2plus_defconfig: Enable ARM erratum 430973 for omap3") - Since
multiple defconfigs can exist from various points of view (multi_v7,
omap2plus etc.. it is always better to enable the erratum from the
Kconfig selection point of view so that downstream kernels dont have
to rediscover this all over again.
Reported-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
ARM errata for am437x, and the other to add ARM errtum
workaround for dra7.
AFAIK these both can wait for v4.7, we can then request them
for stable kernels as needed.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=0ahk
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.7/fixes-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Two fixes for omaps for v4.7 merge window, one to enable
ARM errata for am437x, and the other to add ARM errtum
workaround for dra7.
AFAIK these both can wait for v4.7, we can then request them
for stable kernels as needed.
* tag 'omap-for-v4.7/fixes-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: AM43XX: Enable fixes for Cortex-A9 errata
ARM: OMAP5 / DRA7: Introduce workaround for 801819
Signed-off-by: Olof Johansson <olof@lixom.net>
This replaces:
- "select ARCH_REQUIRE_GPIOLIB" with "select GPIOLIB" as this can
now be selected directly.
- "select ARCH_WANT_OPTIONAL_GPIOLIB" with no dependency: GPIOLIB
is now selectable by everyone, so we need not declare our
intent to select it.
When ordering the symbols the following rationale was used:
if the selects were in alphabetical order, I moved select GPIOLIB
to be in alphabetical order, but if the selects were not
maintained in alphabetical order, I just replaced
"select ARCH_REQUIRE_GPIOLIB" with "select GPIOLIB".
Cc: Michael Büsch <m@bues.ch>
Cc: arm@kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Instead of the full omapdss internal header, include only the platform_data
header.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
The omap_display_init() is implemented in the mach-omap2/display.c so the
declaration should have been there as well.
Change the board files to include display.h to avoid build breakage at the
same time.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
OMAP_DSS_VENC_TYPE_COMPOSITE is 0. There is no need to explicitly set the
connector_type.
This change is needed for the omapdss header cleanup.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
First cycle with Boris as NAND maintainer! Many (most) bullets stolen from him.
Generic:
* Migrated NAND LED trigger to be a generic MTD trigger
NAND:
* Introduction of the "ECC algorithm" concept, to avoid overloading the ECC
mode field too much more
* Replaced the nand_ecclayout infrastructure with something a little more
flexible (finally!) and future proof
* Rework of the OMAP GPMC and NAND drivers; the TI folks pulled some of
this into their own tree as well
* Prepare the sunxi NAND driver to receive DMA support
* Handle bitflips in erased pages on GPMI revisions that do not support
this in hardware.
SPI NOR:
* Start using the spi_flash_read() API for SPI drivers that support it (i.e.,
SPI drivers with special memory-mapped flash modes)
And other small scattered improvments.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=J6KN
-----END PGP SIGNATURE-----
Merge tag 'for-linus-20160523' of git://git.infradead.org/linux-mtd
Pull MTD updates from Brian Norris:
"First cycle with Boris as NAND maintainer! Many (most) bullets stolen
from him.
Generic:
- Migrated NAND LED trigger to be a generic MTD trigger
NAND:
- Introduction of the "ECC algorithm" concept, to avoid overloading
the ECC mode field too much more
- Replaced the nand_ecclayout infrastructure with something a little
more flexible (finally!) and future proof
- Rework of the OMAP GPMC and NAND drivers; the TI folks pulled some
of this into their own tree as well
- Prepare the sunxi NAND driver to receive DMA support
- Handle bitflips in erased pages on GPMI revisions that do not
support this in hardware.
SPI NOR:
- Start using the spi_flash_read() API for SPI drivers that support
it (i.e., SPI drivers with special memory-mapped flash modes)
And other small scattered improvments"
* tag 'for-linus-20160523' of git://git.infradead.org/linux-mtd: (155 commits)
mtd: spi-nor: support GigaDevice gd25lq64c
mtd: nand_bch: fix spelling of "probably"
mtd: brcmnand: respect ECC algorithm set by NAND subsystem
gpmi-nand: Handle ECC Errors in erased pages
Documentation: devicetree: deprecate "soft_bch" nand-ecc-mode value
mtd: nand: add support for "nand-ecc-algo" DT property
mtd: mtd: drop NAND_ECC_SOFT_BCH enum value
mtd: drop support for NAND_ECC_SOFT_BCH as "soft_bch" mapping
mtd: nand: read ECC algorithm from the new field
mtd: nand: fsmc: validate ECC setup by checking algorithm directly
mtd: nand: set ECC algorithm to Hamming on fallback
staging: mt29f_spinand: set ECC algorithm explicitly
CRIS v32: nand: set ECC algorithm explicitly
mtd: nand: atmel: set ECC algorithm explicitly
mtd: nand: davinci: set ECC algorithm explicitly
mtd: nand: bf5xx: set ECC algorithm explicitly
mtd: nand: omap2: Fix high memory dma prefetch transfer
mtd: nand: omap2: Start dma request before enabling prefetch
mtd: nandsim: add __init attribute
mtd: nand: move of_get_nand_xxx() helpers into nand_base.c
...
We get support for three new 32-bit SoC platforms this time. The amount
of changes in arch/arm for any of them is miniscule, as all the
interesting code is in device driver subsystems (irqchip, clk, pinctrl,
...) these days. I'm listing them here, as the addition of the Kconfig
statement is the main relevant milestone for a new platform. In each
case, some drivers are are shared with existing platforms, while
other drivers are added for v4.7 as well, or come in a later release.
- The Aspeed platform is probably the most interesting one, this is
what most whitebox servers use as their baseboard management
controller. We get support for the very common ast2400 and ast2500
SoCs. The OpenBMC project focuses on this chip, and the LWN
article about their ELC 2016 presentation at
https://lwn.net/Articles/683320/ triggered the submission, but the
code comes from IBM's OpenPOWER team rather than the team at
Facebook. There are still a lot more drivers that need to get added
over time, and I hope both teams can work together on that.
- OXNAS is an old platform for Network Attached Storage devices
from Oxford Semiconductor. There are models with ARM10 (!) and
ARM11MPCore cores, but for now, we only support the original ARM9
based versions.
The product lineup was subsequently part of PLX, Avago and now the
new Broadcom Ltd. https://wiki.openwrt.org/doc/hardware/soc/soc.oxnas
has some more information.
- V2M-MPS2 is a prototyping platform from ARM for their Cortex-M
cores and is related to the existing Realview / Versatile Express
lineup, but without MMU. We now support various NOMMU platforms,
so adding a new one is fairly straightforward.
http://infocenter.arm.com/help/topic/com.arm.doc.100112_0100_03_en/
has detailed information about the platform.
Other noteworthy updates:
- Work on LPC32xx has resumed, and Vladimir Zapolskiy and Sylvain Lemieux
are now maintaining the platform. This is an older ARM9 based
platform from NXP (not Freescale), but it remains in use in embedded
markets.
- Kevin Hilman is now co-maintaining the Amlogic Meson platform for both
32-bit and 64-bit ARM, and started contributing some patches.
- As is often the case, work on the OMAP platforms makes up the bulk of
the actual SoC code changes in arch/arm, but there isn't a lot of
that either.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=5oFu
-----END PGP SIGNATURE-----
Merge tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC platform updates from Arnd Bergmann:
"We get support for three new 32-bit SoC platforms this time.
The amount of changes in arch/arm for any of them is miniscule, as all
the interesting code is in device driver subsystems (irqchip, clk,
pinctrl, ...) these days. I'm listing them here, as the addition of
the Kconfig statement is the main relevant milestone for a new
platform. In each case, some drivers are are shared with existing
platforms, while other drivers are added for v4.7 as well, or come in
a later release.
- The Aspeed platform is probably the most interesting one, this is
what most whitebox servers use as their baseboard management
controller. We get support for the very common ast2400 and ast2500
SoCs. The OpenBMC project focuses on this chip, and the LWN
article about their ELC 2016 presentation at
https://lwn.net/Articles/683320/
triggered the submission, but the code comes from IBM's OpenPOWER
team rather than the team at Facebook. There are still a lot more
drivers that need to get added over time, and I hope both teams can
work together on that.
- OXNAS is an old platform for Network Attached Storage devices from
Oxford Semiconductor. There are models with ARM10 (!) and
ARM11MPCore cores, but for now, we only support the original ARM9
based versions. The product lineup was subsequently part of PLX,
Avago and now the new Broadcom Ltd.
https://wiki.openwrt.org/doc/hardware/soc/soc.oxnas
has some more information.
- V2M-MPS2 is a prototyping platform from ARM for their Cortex-M
cores and is related to the existing Realview / Versatile Express
lineup, but without MMU.
We now support various NOMMU platforms, so adding a new one is
fairly straightforward.
http://infocenter.arm.com/help/topic/com.arm.doc.100112_0100_03_en/
has detailed information about the platform.
Other noteworthy updates:
- Work on LPC32xx has resumed, and Vladimir Zapolskiy and Sylvain
Lemieux are now maintaining the platform.
This is an older ARM9 based platform from NXP (not Freescale), but
it remains in use in embedded markets.
- Kevin Hilman is now co-maintaining the Amlogic Meson platform for
both 32-bit and 64-bit ARM, and started contributing some patches.
- As is often the case, work on the OMAP platforms makes up the bulk
of the actual SoC code changes in arch/arm, but there isn't a lot
of that either"
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (42 commits)
MAINTAINERS: ARM/Amlogic: add co-maintainer, misc. updates
MAINTAINERS: add ARM/NXP LPC32XX SoC specific drivers to the section
MAINTAINERS: add new maintainers of NXP LPC32xx SoC
MAINTAINERS: move ARM/NXP LPC32xx record to ARM section
arm: Add Aspeed machine
ARM: lpc32xx: remove duplicate const on lpc32xx_auxdata_lookup
ARM: lpc32xx: remove leftovers of legacy clock source and provider drivers
ARM: lpc32xx: remove reboot header file
ARM: dove: Remove CLK_IS_ROOT
ARM: orion5x: Remove CLK_IS_ROOT
ARM: mv78xx0: Remove CLK_IS_ROOT
ARM: davinci: da850: use clk->set_parent for async3
ARM: davinci: Move clock init after ioremap.
MAINTAINERS: Update ARM Versatile Express platform entry
ARM: vexpress/mps2: introduce MPS2 platform
MAINTAINERS: add maintainer entry for ARM/OXNAS platform
ARM: Add new mach-oxnas
irqchip: versatile-fpga: add new compatible for OX810SE SoC
ARM: uniphier: correct the call order of of_node_put()
MAINTAINERS: fix stale TI DaVinci entries
...
Traditionally we've had two separate branches for cleanups and non-critical
bug fixes, but both of these got smaller with each release and the differences
are rather unclear now, so it seems more appropriate to have a combined
branch.
The most notably change is for OMAP, which gets a small rework to simplify
handling of the AUXDATA mechanism used on machines that are not completely
DT based yet, along with other work that is used as preparation for dropping
the legacy board files.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=au7y
-----END PGP SIGNATURE-----
Merge tag 'armsoc-cleanups-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC cleanups and fixes from Arnd Bergmann:
"Traditionally we've had two separate branches for cleanups and
non-critical bug fixes, but both of these got smaller with each
release and the differences are rather unclear now, so it seems more
appropriate to have a combined branch.
The most notable change is for OMAP, which gets a small rework to
simplify handling of the AUXDATA mechanism used on machines that are
not completely DT based yet, along with other work that is used as
preparation for dropping the legacy board files"
* tag 'armsoc-cleanups-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: dts: exynos: Add interrupt line to MAX8997 PMIC on exynos4210-trats
ARM: dts: exynos: Fix regulator name to avoid forbidden character on exynos4210-trats
ARM: dts: exynos: Add MFC memory banks for Peach boards
ARM: OMAP2+: n900 needs MMC slot names for legacy user space
ARM: OMAP2+: Add more functions to pwm pdata for ir-rx51
ARM: debug: remove extraneous DEBUG_HI3716_UART option
ARM: OMAP2+: Simplify auxdata by using the generic match
of/platform: Allow secondary compatible match in of_dev_lookup
ARM: davinci: use IRQCHIP_DECLARE for cp_intc
ARM: davinci: remove unused DA8XX_NUM_UARTS
ARM: davinci: simplify call to of populate
ARM: DaVinci USB: removed deprecated properties from MUSB config
ARM: rockchip: Fix use of plain integer as NULL pointer
ARM: realview: hide unused 'pmu_device' object
soc: versatile: dynamically detect RealView HBI numbers
* pm-cpufreq: (63 commits)
intel_pstate: Clean up get_target_pstate_use_performance()
intel_pstate: Use sample.core_avg_perf in get_avg_pstate()
intel_pstate: Clarify average performance computation
intel_pstate: Avoid unnecessary synchronize_sched() during initialization
cpufreq: schedutil: Make default depend on CONFIG_SMP
cpufreq: powernv: del_timer_sync when global and local pstate are equal
cpufreq: powernv: Move smp_call_function_any() out of irq safe block
intel_pstate: Clean up intel_pstate_get()
cpufreq: schedutil: Make it depend on CONFIG_SMP
cpufreq: governor: Fix handling of special cases in dbs_update()
cpufreq: intel_pstate: Ignore _PPC processing under HWP
cpufreq: arm_big_little: use generic OPP functions for {init, free}_opp_table
cpufreq: tango: Use generic platdev driver
cpufreq: Fix GOV_LIMITS handling for the userspace governor
cpufreq: mvebu: Move cpufreq code into drivers/cpufreq/
cpufreq: dt: Kill platform-data
mvebu: Use dev_pm_opp_set_sharing_cpus() to mark OPP tables as shared
cpufreq: dt: Identify cpu-sharing for platforms without operating-points-v2
cpufreq: governor: Change confusing struct field and variable names
cpufreq: intel_pstate: Enable PPC enforcement for servers
...
This patch explicitly enables the fixes for the below errata applicable
for AM43x Socs as was done for OMAP4.
754322: Faulty MMU translations following ASID switch
775420: A data cache maintenance operation which aborts,
followed by an ISB, without any DSB in-between,
might lead to deadlock
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add workaround for Cortex-A15 ARM erratum 801819 which says in summary
that "A livelock can occur in the L2 cache arbitration that might
prevent a snoop from completing. Under certain conditions this can
cause the system to deadlock. "
Recommended workaround is as follows:
Do both of the following:
1) Do not use the write-back no-allocate memory type.
2) Do not issue write-back cacheable stores at any time when the cache
is disabled (SCTLR.C=0) and the MMU is enabled (SCTLR.M=1). Because it
is implementation defined whether cacheable stores update the cache when
the cache is disabled it is not expected that any portable code will
execute cacheable stores when the cache is disabled.
For implementations of Cortex-A15 configured without the “L2 arbitration
register slice” option (typically one or two core systems), you must
also do the following:
3) Disable write-streaming in each CPU by setting ACTLR[28:25] = 0b1111
So, we provide an option to disable write streaming on OMAP5 and DRA7.
It is a rare condition to occur and may be enabled selectively based
on platform acceptance of risk.
Applies to: A15 revisions r2p0, r2p1, r2p2, r2p3 or r2p4 and REVIDR[3]
is set to 0.
Based on ARM errata Document revision 18.0 (22 Nov 2013)
Note: the configuration for the workaround needs to be done with
each CPU bringup, since CPU0 bringup is done by bootloader, it is
recommended to have the workaround in the bootloader, kernel also does
ensure that CPU0 has the workaround and makes the workaround active
when CPU1 gets active.
With CONFIG_SMP disabled, it is expected to be done by the bootloader.
This does show significant degradation in synthetic tests such as
mbw (https://packages.qa.debian.org/m/mbw.html)
mbw -n 100 100|grep AVG (on a test platform)
Without enabling the erratum:
AVG Method: MEMCPY Elapsed: 0.13406 MiB: 100.00000 Copy: 745.913 MiB/s
AVG Method: DUMB Elapsed: 0.06746 MiB: 100.00000 Copy: 1482.357 MiB/s
AVG Method: MCBLOCK Elapsed: 0.03058 MiB: 100.00000 Copy: 3270.569 MiB/s
After enabling the erratum:
AVG Method: MEMCPY Elapsed: 0.13757 MiB: 100.00000 Copy: 726.913 MiB/s
AVG Method: DUMB Elapsed: 0.12024 MiB: 100.00000 Copy: 831.668 MiB/s
AVG Method: MCBLOCK Elapsed: 0.09243 MiB: 100.00000 Copy: 1081.942 MiB/s
Most benchmarks are designed for specific performance analysis, so
overall usecase must be considered before making a decision to
enable/disable the erratum workaround.
Pending internal investigation, the erratum is kept disabled by default.
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Tony Lindgren <tony@atomide.com>
Suggested-by: Richard Woodruff <r-woodruff2@ti.com>
Suggested-by: Brad Griffis <bgriffis@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
compatible string if no exact match based on the IO address is found.
This leaves out the need to patch auxdata for each driver when adding
new SoCs. And it also reprotedly fixes the issue of passing auxdata
to a child if the parent instantiates the child from DT as discussed
in the "[PATCH] of/platform: Allow secondary compatible match in
of_dev_lookup" mailing list thread.
As a minimal use case, let's also convert omap pinctrl auxdatato
use a generic match.
There is no need to get this in to the v4.6-rc cycle and it can wait
for v4.7 merge window. Note that these changes have now been sitting
in Linux next for about two weeks so far as I wanted to make sure no
new issues are popping up.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=T39l
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.7/auxdata-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/fixes-non-critical
Merge "non urgent auxdata fix for v4.7 merge window" from Tony Lindgren:
Device tree auxdata handling fix that allows a match based on the
compatible string if no exact match based on the IO address is found.
This leaves out the need to patch auxdata for each driver when adding
new SoCs. And it also reprotedly fixes the issue of passing auxdata
to a child if the parent instantiates the child from DT as discussed
in the "[PATCH] of/platform: Allow secondary compatible match in
of_dev_lookup" mailing list thread.
As a minimal use case, let's also convert omap pinctrl auxdatato
use a generic match.
There is no need to get this in to the v4.6-rc cycle and it can wait
for v4.7 merge window. Note that these changes have now been sitting
in Linux next for about two weeks so far as I wanted to make sure no
new issues are popping up.
* tag 'omap-for-v4.7/auxdata-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: Simplify auxdata by using the generic match
of/platform: Allow secondary compatible match in of_dev_lookup
Testing on ARM encountered the following pair of lockdep-RCU splats:
------------------------------------------------------------------------
===============================
[ INFO: suspicious RCU usage. ]
4.6.0-rc4-next-20160422 #1 Not tainted
-------------------------------
include/trace/events/power.h:328 suspicious rcu_dereference_check() usage!
other info that might help us debug this:
RCU used illegally from idle CPU!
rcu_scheduler_active = 1, debug_locks = 0
RCU used illegally from extended quiescent state!
no locks held by swapper/0/0.
stack backtrace:
CPU: 0 PID: 0 Comm: swapper/0 Not tainted 4.6.0-rc4-next-20160422 #1
Hardware name: Generic OMAP3-GP (Flattened Device Tree)
[<c010f55c>] (unwind_backtrace) from [<c010b64c>] (show_stack+0x10/0x14)
[<c010b64c>] (show_stack) from [<c047acbc>] (dump_stack+0xa8/0xe0)
[<c047acbc>] (dump_stack) from [<c012bc10>] (pwrdm_set_next_pwrst+0xf8/0x1cc)
[<c012bc10>] (pwrdm_set_next_pwrst) from [<c01269fc>] (omap3_enter_idle_bm+0x1b8/0x1e8)
[<c01269fc>] (omap3_enter_idle_bm) from [<c05fa0b8>] (cpuidle_enter_state+0x84/0x408)
[<c05fa0b8>] (cpuidle_enter_state) from [<c0182c1c>] (cpu_startup_entry+0x1c8/0x3f0)
[<c0182c1c>] (cpu_startup_entry) from [<c0b00c20>] (start_kernel+0x354/0x3cc)
------------------------------------------------------------------------
[<c010f55c>] (unwind_backtrace) from [<c010b64c>] (show_stack+0x10/0x14)
[<c010b64c>] (show_stack) from [<c047ac3c>] (dump_stack+0xa8/0xe0)
[<c047ac3c>] (dump_stack) from [<c012c340>] (_pwrdm_state_switch+0x188/0x32c)
[<c012c340>] (_pwrdm_state_switch) from [<c012c4f0>] (_pwrdm_post_transition_cb+0xc/0x14)
[<c012c4f0>] (_pwrdm_post_transition_cb) from [<c012ba74>] (pwrdm_for_each+0x30/0x5c)
[<c012ba74>] (pwrdm_for_each) from [<c012c72c>] (pwrdm_post_transition+0x24/0x30)
[<c012c72c>] (pwrdm_post_transition) from [<c012548c>] (omap_sram_idle+0xfc/0x240)
[<c012548c>] (omap_sram_idle) from [<c0126934>] (omap3_enter_idle_bm+0xf0/0x1e8)
[<c0126934>] (omap3_enter_idle_bm) from [<c05fa038>] (cpuidle_enter_state+0x84/0x408)
[<c05fa038>] (cpuidle_enter_state) from [<c0182b90>] (cpu_startup_entry+0x1c8/0x3f0)
[<c0182b90>] (cpu_startup_entry) from [<c0b00c20>] (start_kernel+0x354/0x3cc)
------------------------------------------------------------------------
These are caused by event tracing from the idle loop, and they were
exposed by commit 293e2421fe ("rcu: Remove superfluous versions of
rcu_read_lock_sched_held()"), which suppressed some false negatives.
The current commit therefore adds the _rcuidle suffix to make RCU aware
of this implicit use of RCU by event tracing, thus preventing both splats.
Reported-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Tony Lindgren <tony@atomide.com>
Cc: Russell King <linux@arm.linux.org.uk>
Reviewed-by: Steven Rostedt <rostedt@goodmis.org>
Cc: <linux-omap@vger.kernel.org>
Cc: <linux-arm-kernel@lists.infradead.org>
Let's pass the slot names in pdata like the legacy code does.
Once we have a generic DT binding for the slot names we can
switch to that.
Tested-by: Ivaylo Dimitrov <ivo.g.dimitrov.75@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Before we start removing omap3 legacy booting support, let's make n900
DT booting behave the same way for ir-rx51 as the legacy booting does.
For now, we need to pass pdata to the ir-rx51 driver. This means that
the n900 tree can move to using DT based booting without having to carry
all the legacy platform data with it when it gets dropped from the mainline
tree.
Note that the ir-rx51 driver is currently disabled because of the
dependency to !ARCH_MULTIPLATFORM. This will get sorted out later
with the help of drivers/pwm/pwm-omap-dmtimer.c. But first we need
to add chained IRQ support to dmtimer code to avoid introducing new
custom frameworks.
So let's just pass the necessary dmtimer functions to ir-rx51 so we
can get it working in the following patch.
Cc: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Ivaylo Dimitrov <ivo.g.dimitrov.75@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The cpufreq-dt-platdev driver supports creation of cpufreq-dt platform
device now, reuse that and remove similar code from platform code.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
- Clockdomain fix for dra7 timer interrupts
- Two fixes for GPMC EDMA binding, I missed the need for a merge with
GPMC changes and EDMA changes
- Fix beagle-x15 eSATA by dropping misconfigured extcon_usb1
- Fix occasional external aborts on 36xx with PM that we've been
chasing for past few months. It turned out to be duplicate restore
of INTC registers that can in some cases cause us to hit erratum 1.106.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=6rQp
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.6/fixes-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Merge "omap fixes for v4.6-rc cycle" from Tony Lindgren:
Fixes for omaps for v4.6-rc cycle:
- Clockdomain fix for dra7 timer interrupts
- Two fixes for GPMC EDMA binding, I missed the need for a merge with
GPMC changes and EDMA changes
- Fix beagle-x15 eSATA by dropping misconfigured extcon_usb1
- Fix occasional external aborts on 36xx with PM that we've been
chasing for past few months. It turned out to be duplicate restore
of INTC registers that can in some cases cause us to hit erratum 1.106.
* tag 'omap-for-v4.6/fixes-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP3: Fix external abort on 36xx waking from off mode idle
ARM: dts: am57xx-beagle-x15: remove extcon_usb1
ARM: dts: am437x: Fix GPMC dma properties
ARM: dts: am33xx: Fix GPMC dma properties
ARM: DRA7: clockdomain: Implement timer workaround for errata i874
For the DRA7xx platform, add IP block data for the McASP, PWMSS,
and GPTimer12 IP blocks. Add lock and unlock functions for the
RTC IP blocks on the DRA7xx, AM33xx, and AM43xx devices. And add
a fix for the hwmod core for device driver unbind operations for
IP blocks with hardreset lines.
Basic build, boot, and PM test results are available here:
http://www.pwsan.com/omap/testlogs/omap-hwmod-a-for-v4.7/20160410132119/
Note that the testbed here does not have the DRA7xx board included yet.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQIcBAABCAAGBQJXEtLeAAoJEMePsQ0LvSpLTMoP/RUOTBa9JlWQJ3E/Pf0GkpT7
8k5u9oy1K3NNNb/Q463Fanyl9k8+G46LFuS+t9YYprdGqgpaW3W7RiawdQVTyxcJ
DWgXuZsOx9FPc7FdP1kF1y6cGAh6ekbPFjPb+FcZ5g5jBE1OW2/LkBiJRnc21LuH
GE3IYYZKYyatybFK+HJFd7uofE+MZ38gtwYbcJtHODHJUz95aMbwDUxPm6x7jAkI
iqbNRdeys7lkNoGDeGvbL8PcxLPE4drT5phxUI2YPzbeoC0UVzBBo8jQLDbgpYX7
GM5CXiqPxTv7HsNcApvDs802dtaJj71IPlBbkQUU5znZhYKQPVHqhn5YyES28csl
rVpNAgTnE2tDi8ZnFHtxxzV9tOysNUuznuQJ9BCpRWvMWL2MdL9YGeNnDkB+Js1n
hCe05yk6DjUuk+1dFjFIkcZX2kZSzEP3BtQtYFU0BhBk5c2Xqx2twgsCmGgHUv6G
D4BTS2aE7Xr009J4QUHiVH4YNBQqe22rJghBWe3v+bN0Iz21uRbnzWbWN9P4UtuZ
acfpMQ436oyYFf/cs/qHbDZpLvkXs3szr0QV28mZYPfIqes3iq8ZKDv0s+H3ORZb
qsGFDAaegZWTst2wIjmo+swqRy7netX3ICdefPO+/x2UX9Loo5vNg+IYCMM9qK5p
3sUg41aQzrxcupfngdcl
=k5TK
-----END PGP SIGNATURE-----
Merge tag 'for-v4.7/omap-hwmod-a' of git://git.kernel.org/pub/scm/linux/kernel/git/pjw/omap-pending into omap-for-v4.7/soc
ARM: OMAP2+: first set of hwmod changes for v4.7
For the DRA7xx platform, add IP block data for the McASP, PWMSS,
and GPTimer12 IP blocks. Add lock and unlock functions for the
RTC IP blocks on the DRA7xx, AM33xx, and AM43xx devices. And add
a fix for the hwmod core for device driver unbind operations for
IP blocks with hardreset lines.
Basic build, boot, and PM test results are available here:
http://www.pwsan.com/omap/testlogs/omap-hwmod-a-for-v4.7/20160410132119/
Note that the testbed here does not have the DRA7xx board included yet.
that broke when we added runtime based SoC revision detection earlier.
It seems suspend worked earlier as things were only partially initialized,
while now we initialize things properly for dra7.
Note that the "ARM: OMAP: Catch callers of revision information prior
to it being populated" had to be reverted as it caused bogus warnings
for other SoCs because omap initcalls bail out based on revision being
set to 0 for other SoCs. These initcalls will mostly just disappear
when we drop support for omap3 legacy booting.
Also included is a fix for dra7 sys_32k_ck clock source that is not
enabled on boot making system fall back to using emulated clock.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=0X4E
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.6/fixes-rc2-v2-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Merge "omap fixes against v4.6-rc2" from Tony Lindgren
Fixes for omaps against v4.6-rc2, mostly to fix suspend for beagle-x15
that broke when we added runtime based SoC revision detection earlier.
It seems suspend worked earlier as things were only partially initialized,
while now we initialize things properly for dra7.
Note that the "ARM: OMAP: Catch callers of revision information prior
to it being populated" had to be reverted as it caused bogus warnings
for other SoCs because omap initcalls bail out based on revision being
set to 0 for other SoCs. These initcalls will mostly just disappear
when we drop support for omap3 legacy booting.
Also included is a fix for dra7 sys_32k_ck clock source that is not
enabled on boot making system fall back to using emulated clock.
* tag 'omap-for-v4.6/fixes-rc2-v2-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (198 commits)
Revert "ARM: OMAP: Catch callers of revision information prior to it being populated"
ARM: OMAP: Catch callers of revision information prior to it being populated
ARM: dts: dra7: Correct clock tree for sys_32k_ck
ARM: OMAP: DRA7: Provide proper class to omap2_set_globals_tap
ARM: OMAP: DRA7: wakeupgen: Skip SAR save for wakeupgen
Linux 4.6-rc2
v4l2-mc: avoid warning about unused variable
Convert straggling drivers to new six-argument get_user_pages()
.mailmap: add Christophe Ricard
Make CONFIG_FHANDLE default y
mm/page_isolation.c: fix the function comments
oom, oom_reaper: do not enqueue task if it is on the oom_reaper_list head
mm/page_isolation: fix tracepoint to mirror check function behavior
mm/rmap: batched invalidations should use existing api
x86/mm: TLB_REMOTE_SEND_IPI should count pages
mm: fix invalid node in alloc_migrate_target()
include/linux/huge_mm.h: return NULL instead of false for pmd_trans_huge_lock()
mm, kasan: fix compilation for CONFIG_SLAB
MAINTAINERS: orangefs mailing list is subscribers-only
net: mvneta: fix changing MTU when using per-cpu processing
...
Move NAND specific device tree parsing to NAND driver.
The NAND controller node must have a compatible id, register space
resource and interrupt resource.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Acked-by: Brian Norris <computersforpeace@gmail.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Deprecate nand register passing via platform data and use
gpmc_omap_get_nand_ops() instead.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Acked-by: Brian Norris <computersforpeace@gmail.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Depending on timing during the resume path from off mode on 36xx, we may
see external aborts. These seem to be caused by the following:
- OMAP3 Advisory 1.62 "MPU Cannot Exit from Standby" says we need to
disable intc autoidle before WFI
- DM3730 Advisory 1.106 "MPU Leaves MSTANDBY State Before IDLEREQ of
Interrupt Controller is Released" says we need to wait before
accessing intc
omap3_intc_resume_idle restores the intc autoidle for all resume paths,
however in the resume path from off mode only it is also being restored
by omap_intc_restore_context before this call to omap3_intc_resume_idle
happens. The second restore of the intc autoidle in this path is what
appears to be causing the external abort so for the off mode resume path
let's rely on omap_intc_restore_context to restore intc autoidle, and
for all other paths let omap3_intc_resume_idle handle it as it is now.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
FROZEN hotplug notifiers are not handled and do not have to be. Insert
a comment to remember that the lack of the FROZEN transitions is no
accident.
Cc: Tony Lindgren <tony@atomide.com>
Cc: Santosh Shilimkar <ssantosh@kernel.org>
Cc: linux-omap@vger.kernel.org
Signed-off-by: Anna-Maria Gleixner <anna-maria@linutronix.de>
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Open Switch Retention(OSWR) is a retention state which is unsupported
in DRA7 SoC. This state is achieved when power state is set to
retention and logic power state is set to OFF.
Even though DRA7 architecture is a OMAP derivative, none of the
powerdomains are actually implemented to achieve OSWR in the SoC.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
When the power domain is in "ON" state, the memories should be always
in "ON", even though the hardware register allows other states to be
written, wrong states may confuse certain hardware blocks.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Erratum i892 as will be documented in the upcoming G or later revision
of DRA7xx/ AM57xx errata documentation (SPRZ398F) states that L3 clock
needs to be kept active all the time to ensure that asymmetric aging
degradation is minimal and within the design allowed margin.
By allowing core domain to transition to INA and allowing L3 clock to be
turned off for extended periods of time, there is a risk of functional
issues and device failure as a result.
Ref: http://www.ti.com/lit/er/sprz429h/sprz429h.pdf
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The directory arch/arm/mach-omap2 is only selected for compilation if
CONFIG_ARCH_OMAP2PLUS is selected. CONFIG_ARCH_OMAP2PLUS itself is a
silent option and all machines selecting this option are multiplatform
devices. As a consequence checks for CONFIG_ARCH_MULTIPLATFORM as well
as CONFIG_ARCH_OMAP2PLUS within that directory are superfluous and can
be removed.
Signed-off-by: Jonas Rabenstein <jonas.rabenstein@studium.uni-erlangen.de>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
For DRA7xx platforms, add a workaround for missed timer interrupts
that appears to be due to an integration bug (erratum i874)
Basic build, boot, and PM test logs are available here:
http://www.pwsan.com/omap/testlogs/omap-fixes-b-for-v4.6-rc/20160413020850/
(The DRA7xx board here has not yet been added into the testbed.)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=6XvG
-----END PGP SIGNATURE-----
Merge tag 'for-v4.6-rc/omap-fixes-b' of git://git.kernel.org/pub/scm/linux/kernel/git/pjw/omap-pending into omap-for-v4.6/fixes
ARM: OMAP2+: clockdomain: another fix for v4.6-rc
For DRA7xx platforms, add a workaround for missed timer interrupts
that appears to be due to an integration bug (erratum i874)
Basic build, boot, and PM test logs are available here:
http://www.pwsan.com/omap/testlogs/omap-fixes-b-for-v4.6-rc/20160413020850/
(The DRA7xx board here has not yet been added into the testbed.)
The omap_hwmod _enable() function can return success without setting
the hwmod state to _HWMOD_STATE_ENABLED for IPs with reset lines when
all of the reset lines are asserted. The omap_hwmod _idle() function
also performs a similar check, but after checking for the hwmod state
first. This triggers the WARN when pm_runtime_get and pm_runtime_put
are invoked on IPs with all reset lines asserted. Reverse the checks
for hwmod state and reset lines status to fix this.
Issue found during a unbind operation on a device with reset lines
still asserted, example backtrace below
------------[ cut here ]------------
WARNING: CPU: 1 PID: 879 at arch/arm/mach-omap2/omap_hwmod.c:2207 _idle+0x1e4/0x240()
omap_hwmod: mmu_dsp: idle state can only be entered from enabled state
Modules linked in:
CPU: 1 PID: 879 Comm: sh Not tainted 4.4.0-00008-ga989d951331a #3
Hardware name: Generic OMAP5 (Flattened Device Tree)
[<c0018e60>] (unwind_backtrace) from [<c0014dc4>] (show_stack+0x10/0x14)
[<c0014dc4>] (show_stack) from [<c037ac28>] (dump_stack+0x90/0xc0)
[<c037ac28>] (dump_stack) from [<c003f420>] (warn_slowpath_common+0x78/0xb4)
[<c003f420>] (warn_slowpath_common) from [<c003f48c>] (warn_slowpath_fmt+0x30/0x40)
[<c003f48c>] (warn_slowpath_fmt) from [<c0028c20>] (_idle+0x1e4/0x240)
[<c0028c20>] (_idle) from [<c0029080>] (omap_hwmod_idle+0x28/0x48)
[<c0029080>] (omap_hwmod_idle) from [<c002a5a4>] (omap_device_idle+0x3c/0x90)
[<c002a5a4>] (omap_device_idle) from [<c0427a90>] (__rpm_callback+0x2c/0x60)
[<c0427a90>] (__rpm_callback) from [<c0427ae4>] (rpm_callback+0x20/0x80)
[<c0427ae4>] (rpm_callback) from [<c0427f84>] (rpm_suspend+0x138/0x74c)
[<c0427f84>] (rpm_suspend) from [<c0428b78>] (__pm_runtime_idle+0x78/0xa8)
[<c0428b78>] (__pm_runtime_idle) from [<c041f514>] (__device_release_driver+0x64/0x100)
[<c041f514>] (__device_release_driver) from [<c041f5d0>] (device_release_driver+0x20/0x2c)
[<c041f5d0>] (device_release_driver) from [<c041d85c>] (unbind_store+0x78/0xf8)
[<c041d85c>] (unbind_store) from [<c0206df8>] (kernfs_fop_write+0xc0/0x1c4)
[<c0206df8>] (kernfs_fop_write) from [<c018a120>] (__vfs_write+0x20/0xdc)
[<c018a120>] (__vfs_write) from [<c018a9cc>] (vfs_write+0x90/0x164)
[<c018a9cc>] (vfs_write) from [<c018b1f0>] (SyS_write+0x44/0x9c)
[<c018b1f0>] (SyS_write) from [<c0010420>] (ret_fast_syscall+0x0/0x1c)
---[ end trace a4182013c75a9f50 ]---
While at this, fix the sequence in _shutdown() as well, though there
is no easy reproducible scenario.
Fixes: 747834ab83 ("ARM: OMAP2+: hwmod: revise hardreset behavior")
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Add the hwmod data for GPTimer 12. GPTimer 12 is present in
WKUPAON power domain and is clocked from a secure 32K clock.
GPTimer 12 serves as a secure timer on HS devices, but is
available for kernel on regular GP devices.
The hwmod link is registered only on GP devices. The hwmod data
also reused the existing timer class instead of reintroducing
the identical dra7xx_timer_secure_sysc class which was dropped
in commit edec178633 ("ARM: DRA7: hwmod: Fix the hwmod class
for GPTimer4").
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Hook omap_hwmod_rtc_unlock/lock functions into RTC hwmod,
so that SYSCONFIG register is updated properly.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Hook omap_hwmod_rtc_unlock/lock functions into RTC hwmod,
so that SYSCONFIG register is updated properly
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
RTC IP have kicker feature which prevents spurious writes to its registers.
In order to write into any of the RTC registers, KICK values has to be
written to KICK registers. Also, RTC busy flag needs to be polled for
non-TC registers as well, without which update is not proper and confirmed
it by testing on DRA7-evm.
Introduce omap_hwmod_rtc_unlock/lock functions, which writes into these
KICK registers inorder to lock and unlock RTC registers.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
[paul@pwsan.com: fixed subject line]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Add hwmod entries for the PWMSS on DRA7.
Set l4_root_clk_div as the main_clk of PWMSS. It is fixed-factored clock
equal to L4PER2_L3_GICLK/2(l3_iclk_div/2).
Signed-off-by: Vignesh R <vigneshr@ti.com>
[fcooper@ti.com: Do not add eQEP, ePWM and eCAP hwmod entries]
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
[paul@pwsan.com: fixed sparse warnings; added missing comments]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Add missing data for all McASP ports for the dra7 family
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Errata Title:
i874: TIMER5/6/7/8 interrupts not propagated
Description:
When TIMER5, TIMER6, TIMER7, or TIMER8 clocks are enabled
(CM_IPU_TIMER5/6/7/8_CLKCTRL[0:1]MODULEMODE=0x2:ENABLE) and the CD-IPU
is in HW_AUTO mode (CM_IPU_CLKSTCTRL[0:1]CLKTRCTRL=0x3:HW_AUTO) the
corresponding TIMER will continue counting, but enabled interrupts
will not be propagated to the destinations (MPU, DSP, etc) in the
SoC until the TIMER registers are accessed from the CPUs (MPU, DSP
etc.). This can result in missed timer interrupts.
Workaround:
In order for TIMER5/6/7/8 interrupts to be propagated and serviced
correctly the CD_IPU domain should be set to SW_WKUP mode
(CM_IPU_CLKSTCTRL[0:1]CLKTRCTRL=0x2:SW_WKUP).
The above workaround is achieved by switching the IPU clockdomain
flags from HWSUP_SWSUP to SWSUP only.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
omap_rev is used to detect various SoC types, however any misuse of
the usage by invoking it earlier than it being populated will result
in invalid results. Lets flag them as early as possible to prevent
unintended side effects taking place. We get 0 if it is uninitialized
and -1 when detection is done using device tree (as the case was for
DRA7 as the case was prior to commit 06c2d368fc ("ARM: OMAP: DRA7:
Make use of omap_revision information for soc_is* calls")
Signed-off-by: Nishanth Menon <nm@ti.com>
Tested-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
When commit 06c2d368fc ("ARM: OMAP: DRA7: Make use of omap_revision
information for soc_is* calls") introduced SoC check using
omap_revision, it missed providing DRA7 as class for initializing
the omap_version variable. Without doing this, soc_is_dra7xx() will
fail and as a result, omap4_pm_init_early never initializes the dra7
erratum for CPU power state. This causes the suspend path to fail
on DRA7 devices.
Fixes: 06c2d368fc ("ARM: OMAP: DRA7: Make use of omap_revision information for soc_is* calls")
Signed-off-by: Nishanth Menon <nm@ti.com>
Tested-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
DRA7 has no SAR region for automated save and restore of wakeupgen,
which does not make real since the SoC really does not do legacy OFF
mode anymore. Further wakeupgen should never loose context in CSWR
retention mode for MPU domain on DRA7 since that is the deepest state
we will enter.
So, just skip, instead of oopsing as follows while attemptint to enter
suspend on BeagleBoard-X15.
[ 55.589771] Unable to handle kernel paging request at virtual address 00002684
[ 55.589771] pgd = ec69c000
[...]
[ 55.589771] [<c0123cc8>] (irq_notifier) from [<c015ad70>] (notifier_call_chain+0x4c/0x8c)
[ 55.589771] [<c015ad70>] (notifier_call_chain) from [<c021469c>] (cpu_cluster_pm_enter+0x2c/0x78)
[ 55.589771] [<c021469c>] (cpu_cluster_pm_enter) from [<c0514508>] (syscore_suspend+0xb8/0x31c)
[ 55.589771] [<c0514508>] (syscore_suspend) from [<c0197d24>] (suspend_devices_and_enter+0x308/0x9e4)
[ 55.589771] [<c0197d24>] (suspend_devices_and_enter) from [<c0198a40>] (pm_suspend+0x640/0x75c)
[ 55.589771] [<c0198a40>] (pm_suspend) from [<c0196bcc>] (state_store+0x64/0xb8)
[ 55.589771] [<c0196bcc>] (state_store) from [<c0307914>] (kernfs_fop_write+0xc0/0x1bc)
[ 55.589771] [<c0307914>] (kernfs_fop_write) from [<c028ac80>] (__vfs_write+0x1c/0xd8)
[ 55.589771] [<c028ac80>] (__vfs_write) from [<c028bb70>] (vfs_write+0x90/0x16c)
[ 55.589771] [<c028bb70>] (vfs_write) from [<c028c890>] (SyS_write+0x44/0x9c)
[ 55.589771] [<c028c890>] (SyS_write) from [<c0107840>] (ret_fast_syscall+0x0/0x1c)
[...]
Signed-off-by: Nishanth Menon <nm@ti.com>
Tested-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Silicon Rev 2.0 is a minor variant of Rev 1.0. Rev 2.0 is an incremental revision
with various fixes including the following:
- Reset logic fixes
- Few asymmetric aging logic fixes
- Ethernet speed fixes
- EDMA fixes for McASP
Signed-off-by: Vishal Mahaveer <vishalm@ti.com>
Acked-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The following commits:
commit 3fa609755c ("ARM: omap2: restore OMAP4 barrier behaviour")
commit f746929ffd ("Revert "ARM: OMAP4: remove dead kconfig option OMAP4_ERRATA_I688"")
and
commit ea827ad5ff ("ARM: DRA7: Provide proper IO map table")
came in around the same time, unfortunately this seem to have missed
initializing the barrier for DRA7 platforms - omap5_map_io was reused
for dra7 till it was split out by the last patch. barrier_init
needs to be hence carried forward as it is valid for DRA7 family of
processors as they are for OMAP5.
Fixes: ea827ad5ff ("ARM: DRA7: Provide proper IO map table")
Cc: stable@vger.kernel.org # v4.1+
Reported-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reported-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Fix a longstanding bug in the hwmod code that could cause
hardware SYSCONFIG register values to not match the kernel's
idea of what they should be, and that could result in lower
performance during IP block idle entry.
Basic build, boot, and PM test logs are available here:
http://www.pwsan.com/omap/testlogs/omap-hwmod-fixes-a-for-v4.6-rc/20160326231727/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=MWxZ
-----END PGP SIGNATURE-----
Merge tag 'for-v4.6-rc/omap-fixes-a' of git://git.kernel.org/pub/scm/linux/kernel/git/pjw/omap-pending into omap-for-v4.6/fixes
ARM: OMAP2+: first hwmod fix for v4.6-rc
Fix a longstanding bug in the hwmod code that could cause
hardware SYSCONFIG register values to not match the kernel's
idea of what they should be, and that could result in lower
performance during IP block idle entry.
Basic build, boot, and PM test logs are available here:
http://www.pwsan.com/omap/testlogs/omap-hwmod-fixes-a-for-v4.6-rc/20160326231727/
Commit 127500ccb7 ("ARM: OMAP2+: Only write the sysconfig on idle
when necessary") talks about verification of sysconfig cache value before
updating it, only during idle path. But the patch is adding the
verification in the enable path. So, adding the check in a proper place
as per the commit description.
Not keeping this check during enable path as there is a chance of losing
context and it is safe to do on idle as the context of the register will
never be lost while the device is active.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Acked-by: Tero Kristo <t-kristo@ti.com>
Cc: Jon Hunter <jonathanh@nvidia.com>
Cc: <stable@vger.kernel.org> # 3.12+
Fixes: commit 127500ccb7 "ARM: OMAP2+: Only write the sysconfig on idle when necessary"
[paul@pwsan.com: appears to have been caused by my own mismerge of the
originally posted patch]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Newly added support for additional SoCs:
- Axis Artpec-6 SoC family
- Allwinner A83T SoC
- Mediatek MT7623
- NXP i.MX6QP SoC
- ST Microelectronics stm32f469 microcontroller
New features:
- SMP support for Mediatek mt2701
- Big-endian support for NXP i.MX
- DaVinci now uses the new DMA engine dma_slave_map
- OMAP now uses the new DMA engine dma_slave_map
- earlyprintk support for palmchip uart on mach-tango
- delay timer support for orion
Other:
- Exynos PMU driver moved out to drivers/soc/
- Various smaller updates for Renesas, Xilinx, PXA, AT91, OMAP, uniphier
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=ynNj
-----END PGP SIGNATURE-----
Merge tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC platform updates from Arnd Bergmann:
"Newly added support for additional SoCs:
- Axis Artpec-6 SoC family
- Allwinner A83T SoC
- Mediatek MT7623
- NXP i.MX6QP SoC
- ST Microelectronics stm32f469 microcontroller
New features:
- SMP support for Mediatek mt2701
- Big-endian support for NXP i.MX
- DaVinci now uses the new DMA engine dma_slave_map
- OMAP now uses the new DMA engine dma_slave_map
- earlyprintk support for palmchip uart on mach-tango
- delay timer support for orion
Other:
- Exynos PMU driver moved out to drivers/soc/
- Various smaller updates for Renesas, Xilinx, PXA, AT91, OMAP,
uniphier"
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (83 commits)
ARM: uniphier: rework SMP code to support new System Bus binding
ARM: uniphier: add missing of_node_put()
ARM: at91: avoid defining CONFIG_* symbols in source code
ARM: DRA7: hwmod: Add data for eDMA tpcc, tptc0, tptc1
ARM: imx: Make reset_control_ops const
ARM: imx: Do L2 errata only if the L2 cache isn't enabled
ARM: imx: select ARM_CPU_SUSPEND only for imx6
dmaengine: pxa_dma: fix the maximum requestor line
ARM: alpine: select the Alpine MSI controller driver
ARM: pxa: add the number of DMA requestor lines
dmaengine: mmp-pdma: add number of requestors
dma: mmp_pdma: Add the #dma-requests DT property documentation
ARM: OMAP2+: Add rtc hwmod configuration for ti81xx
ARM: s3c24xx: Avoid warning for inb/outb
ARM: zynq: Move early printk virtual address to vmalloc area
ARM: DRA7: hwmod: Add custom reset handler for PCIeSS
ARM: SAMSUNG: Remove unused register offset definition
ARM: EXYNOS: Cleanup header files inclusion
drivers: soc: samsung: Enable COMPILE_TEST
MAINTAINERS: Add maintainers entry for drivers/soc/samsung
...
A few simple cleanups across multiple platforms, not much standing out:
- lpc32xx removes its private implementation of the clk API, after
generic code was merged in 4.5
- all unused Makefile.boot files get removed
- a number of simplifications for shmobile
- asm/clkdev.h gets replaced with the asm-generic version after
all mach/clkdev.h implementations are gone
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=ZTl9
-----END PGP SIGNATURE-----
Merge tag 'armsoc-cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC cleanups from Arnd Bergmann:
"A few simple cleanups across multiple platforms, not much standing
out:
- lpc32xx removes its private implementation of the clk API, after
generic code was merged in 4.5
- all unused Makefile.boot files get removed
- a number of simplifications for shmobile
- asm/clkdev.h gets replaced with the asm-generic version after all
mach/clkdev.h implementations are gone"
* tag 'armsoc-cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: shmobile: Kconfig: Get rid of old comment
ARM: shmobile: Consolidate SCU mapping code
arm: lpc32xx: remove direct control of GPIOs from shared mach file
arm: lpc32xx: remove selected HAVE_IDE
arm: lpc32xx: switch to common clock framework
ARM: Use generic clkdev.h header
ARM: plat-versatile: Remove unused clock.c file
ARM: netx: remove redundant "depends on ARCH_NETX"
ARM: integrator: remove redundant select in Kconfig
ARM: drop unused Makefile.boot of Multiplatform SoCs
ARM: mvebu: add missing of_node_put()
ARM: shmobile: r8a7779: Remove remainings of removed SCU boot setup code
ARM: shmobile: Typo s/MIPDR/MPIDR/
ARM: shmobile: Add includes providing forward declarations
ARM: shmobile: rcar-gen2: Make rcar_gen2_dma_contiguous static
ARM: mv78xx0: use "depends on" instead of "if" after prompt
As usual, we queue up a few fixes that don't seem urgent enough to go in
through -rc.
- a number of randconfig warning fixes from Arnd
- various small fixes for OMAP
- one somewhat larger patch to restore the OMAP3 cpuidle
tuning that was lost in a cleanup
- a small regression fix for cns3xxx PCI
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=YJmM
-----END PGP SIGNATURE-----
Merge tag 'armsoc-fixes-nc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC non-urgent fixes from Arnd Bergmann:
"As usual, we queue up a few fixes that don't seem urgent enough to go
in through -rc.
- a number of randconfig warning fixes from Arnd
- various small fixes for OMAP
- one somewhat larger patch to restore the OMAP3 cpuidle tuning that
was lost in a cleanup
- a small regression fix for cns3xxx PCI"
* tag 'armsoc-fixes-nc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (26 commits)
CNS3xxx: Fix PCI cns3xxx_write_config()
MAINTAINERS: unify email addrs for Kevin Hilman
CNS3xxx: remove unused *_VIRT definitions
ARM: OMAP2+: Fix hwmod clock for l4_ls
soc: TI knav_qmss: fix dma_addr_t printing
ARM: prima2: always enable reset controller
ARM: socfpga: hide unused functions
ARM: ux500: fix ureachable iounmap()
ARM: ks8695: fix __initdata annotation
ARM: mvebu: mark mvebu_hwcc_pci_nb as __maybe_unused
ARM: mv78xx0: avoid unused function warning
ARM: orion: only select I2C_BOARDINFO when using I2C
ARM: OMAP2+: Fix out of range register access with syscon_config.max_register
ARM: OMAP3: Add cpuidle parameters table for omap3430
ARM: davinci: make I2C support optional
ARM: davinci: DA8xx+DMx combined kernels need PATCH_PHYS_VIRT
ARM: davinci: avoid unused mityomapl138_pn_info variable
ARM: davinci: limit DT support to DA850
ARM: DRA7: hwmod: Add reset data for PCIe
ARM: DRA7: hwmod: Fix OCP2SCP sysconfig
...
Here's the big tty/serial driver pull request for 4.6-rc1.
Lots of changes in here, Peter has been on a tear again, with lots of
refactoring and bugs fixes, many thanks to the great work he has been
doing. Lots of driver updates and fixes as well, full details in the
shortlog.
All have been in linux-next for a while with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlbp8z8ACgkQMUfUDdst+ym1vwCgnOOCORaZyeQ4QrcxPAK5pHFn
VrMAoNHvDgNYtG+Hmzv25Lgp3HnysPin
=MLRG
-----END PGP SIGNATURE-----
Merge tag 'tty-4.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial updates from Greg KH:
"Here's the big tty/serial driver pull request for 4.6-rc1.
Lots of changes in here, Peter has been on a tear again, with lots of
refactoring and bugs fixes, many thanks to the great work he has been
doing. Lots of driver updates and fixes as well, full details in the
shortlog.
All have been in linux-next for a while with no reported issues"
* tag 'tty-4.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (220 commits)
serial: 8250: describe CONFIG_SERIAL_8250_RSA
serial: samsung: optimize UART rx fifo access routine
serial: pl011: add mark/space parity support
serial: sa1100: make sa1100_register_uart_fns a function
tty: serial: 8250: add MOXA Smartio MUE boards support
serial: 8250: convert drivers to use up_to_u8250p()
serial: 8250/mediatek: fix building with SERIAL_8250=m
serial: 8250/ingenic: fix building with SERIAL_8250=m
serial: 8250/uniphier: fix modular build
Revert "drivers/tty/serial: make 8250/8250_ingenic.c explicitly non-modular"
Revert "drivers/tty/serial: make 8250/8250_mtk.c explicitly non-modular"
serial: mvebu-uart: initial support for Armada-3700 serial port
serial: mctrl_gpio: Add missing module license
serial: ifx6x60: avoid uninitialized variable use
tty/serial: at91: fix bad offset for UART timeout register
tty/serial: at91: restore dynamic driver binding
serial: 8250: Add hardware dependency to RT288X option
TTY, devpts: document pty count limiting
tty: goldfish: support platform_device with id -1
drivers: tty: goldfish: Add device tree bindings
...
Force the DRA7xx Ethernet internal clock source to stay enabled
per TI erratum i877:
http://www.ti.com/lit/er/sprz429h/sprz429h.pdf
Otherwise, if the Ethernet internal clock source is disabled, the
chip will age prematurely, and the RGMII I/O timing will soon
fail to meet the delay time and skew specifications for 1000Mbps
Ethernet.
This fix should go in as soon as possible.
Basic build, boot, and PM test results are available here:
http://www.pwsan.com/omap/testlogs/omap-critical-fixes-for-v4.5-rc/20160307014209/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=kJw8
-----END PGP SIGNATURE-----
Merge tag 'for-v4.5-rc/omap-critical-fixes-a' of git://git.kernel.org/pub/scm/linux/kernel/git/pjw/omap-pending into fixes
ARM: OMAP2+: critical DRA7xx fix for v4.5-rc
Force the DRA7xx Ethernet internal clock source to stay enabled
per TI erratum i877:
http://www.ti.com/lit/er/sprz429h/sprz429h.pdf
Otherwise, if the Ethernet internal clock source is disabled, the
chip will age prematurely, and the RGMII I/O timing will soon
fail to meet the delay time and skew specifications for 1000Mbps
Ethernet.
This fix should go in as soon as possible.
Basic build, boot, and PM test results are available here:
http://www.pwsan.com/omap/testlogs/omap-critical-fixes-for-v4.5-rc/20160307014209/
* tag 'for-v4.5-rc/omap-critical-fixes-a' of git://git.kernel.org/pub/scm/linux/kernel/git/pjw/omap-pending:
ARM: dts: dra7: do not gate cpsw clock due to errata i877
ARM: OMAP2+: hwmod: Introduce ti,no-idle dt property
Signed-off-by: Olof Johansson <olof@lixom.net>
Introduce a dt property, ti,no-idle, that prevents an IP to idle at any
point. This is to handle Errata i877, which tells that GMAC clocks
cannot be disabled.
Acked-by: Roger Quadros <rogerq@ti.com>
Tested-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Acked-by: Rob Herring <robh@kernel.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
- Enable runtime revision detection for dra7 to avoid multiple dts
files for various variants
- Add dma_slave_map for omap1/2/3 legacy mode booting
- Add RTC interconnect target data for ti81xx and am43x
- Add custom reset handler for PCIeSS
- Add eDMA interconnect target data for dra7
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=tJb7
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.6/soc-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/soc
Merge "omap soc changes for v4.6 merge window" from Tony Lindgren:
SoC related changes for omaps for v4.6 merge window:
- Enable runtime revision detection for dra7 to avoid multiple dts
files for various variants
- Add dma_slave_map for omap1/2/3 legacy mode booting
- Add RTC interconnect target data for ti81xx and am43x
- Add custom reset handler for PCIeSS
- Add eDMA interconnect target data for dra7
* tag 'omap-for-v4.6/soc-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: DRA7: hwmod: Add data for eDMA tpcc, tptc0, tptc1
ARM: OMAP2+: Add rtc hwmod configuration for ti81xx
ARM: DRA7: hwmod: Add custom reset handler for PCIeSS
ARM: OMAP2+: DMA: Provide dma_slave_map to omap-dma for legacy boot
ARM: OMAP1: DMA: Provide dma_slave_map to omap-dma
ARM: OMAP: DRA7: Make use of omap_revision information for soc_is* calls
ARM: AM43XX: hwmod: Add rtc hwmod
ARM: DRA7: hwmod: Add reset data for PCIe
ARM: DRA7: hwmod: Fix OCP2SCP sysconfig
ARM: OMAP2+: hwmod data: Add SSI data for omap36xx
for the v4.5-rc cycle:
- Add back optimized cpuidle parameters for 34xx that were
incorrecly removed earlier with cpuidle cleanup
- Fix SSI for omap36xx to get modem working on N950/N9
- A series of omap hwmod fixes via Paul Walmsley <paul@pwsan.com>
to fix SSI for omap36xx for modem on N950/N9, fix for
OCP2SCP sysconfig idle mode, and reset data for PCIe on
dra7
- Fix out of range register access for omap3 control module
if syscon max_register is initialized like v4.6 will be
doing
- Fix l4_ls interconnect clocks for 81xx, it should always
be sysclk6_ck
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=pwoK
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.6/fixes-not-urgent-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/fixes-non-critical
Merge "omap non-urgent fixes for v4.6 merge window" from Tony Lindgren:
Fixes for omaps for v4.6 merge window that are not urgent
for the v4.5-rc cycle:
- Add back optimized cpuidle parameters for 34xx that were
incorrecly removed earlier with cpuidle cleanup
- Fix SSI for omap36xx to get modem working on N950/N9
- A series of omap hwmod fixes via Paul Walmsley <paul@pwsan.com>
to fix SSI for omap36xx for modem on N950/N9, fix for
OCP2SCP sysconfig idle mode, and reset data for PCIe on
dra7
- Fix out of range register access for omap3 control module
if syscon max_register is initialized like v4.6 will be
doing
- Fix l4_ls interconnect clocks for 81xx, it should always
be sysclk6_ck
* tag 'omap-for-v4.6/fixes-not-urgent-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: Fix hwmod clock for l4_ls
ARM: OMAP2+: Fix out of range register access with syscon_config.max_register
ARM: OMAP3: Add cpuidle parameters table for omap3430
ARM: DRA7: hwmod: Add reset data for PCIe
ARM: DRA7: hwmod: Fix OCP2SCP sysconfig
ARM: OMAP2+: hwmod data: Add SSI data for omap36xx
Without this booting t410 can fail randomly with no output
depending on the .config options chosen. Enabling debug_ll
causes the problem to go away. I narrowed this down to USB
by disabling one module at a time.
Acked-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
These patches add RTC support for the AM43xx, and add support for
the DRA7xx eDMA controller's TPCC, TPTC0, and TPTC1 IP blocks.
Also included is a workaround for PRCM hardreset control of the DRA7xx
PCIe subsystem.
Note that I do not have a DRA7xx board, and therefore cannot
test any patches for that SoC family.
Basic build, boot, and PM test logs can be found here:
http://www.pwsan.com/omap/testlogs/omap-hwmod-b-for-v4.6/20160301021258/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJW1WdKAAoJEMePsQ0LvSpLoO8P/A05egqdZtbWCte8tK4/E+d1
fdzaev9dC8I6rWlxV6PTFZL8Hw28XtQZDYqV2voRE5nxma1L05Uang2c2tNmO7oH
Qa7pvD/m6vy3A2ZIKgTJeV7Elc5SNEmPQq6/1z1viWni4oUFWrsP1cKPTmUOhTNu
cx6Q2oxkoGlLRmonygJ49da6XShPMIOolDUNfOKFuSmt80RUor2j1Wpu+3wlVZvr
53jSLG8C+RgiUeBT90PUOvI7dAfocOV+G8CnH7/Fnss9+L2skiKwOOUNudGBz3JZ
elAwjyiCkBlo3VGSRk4UarXuzAdCqZqvLSemYZ1JbYT3SbbIWovJ9nX17y7Gl7RT
4KnGW0P+yeYYj9iEwUOs1Yj4DgFTbgkmHqkF2zWPGawjj3AMUKquvYVR1d+Oz3NR
77wdAPIKWWRJ5V8QiQhKiZjpj4TkR7KT1fAF78Kf4eMXwy5tbXUkXyKpj0Izi1Z2
Oe2NHcGOMXbSBYSBK0N9sYXFWKhE3CRkEZ3yoYwTwoDYpDuMWffnRX1a0TGseUb3
xX9j+818/FyKhwEdL4rIHwOYW/iITLUOSUAOt2lnM2xWx3G1aNX7RjreOdobVm7Z
8ZVbX2zFBrP8Fe964ZutoG7FjBqurrOtoJUrZPEPWOcjDMPBi9JfRfwtLzglAnXh
IUglDUxMXscaQulEez3J
=ospe
-----END PGP SIGNATURE-----
Merge tag 'for-v4.6/omap-hwmod-b' of git://git.kernel.org/pub/scm/linux/kernel/git/pjw/omap-pending into omap-for-v4.6/soc
ARM: OMAP2+: second set of hwmod changes for v4.6
These patches add RTC support for the AM43xx, and add support for
the DRA7xx eDMA controller's TPCC, TPTC0, and TPTC1 IP blocks.
Also included is a workaround for PRCM hardreset control of the DRA7xx
PCIe subsystem.
Note that I do not have a DRA7xx board, and therefore cannot
test any patches for that SoC family.
Basic build, boot, and PM test logs can be found here:
http://www.pwsan.com/omap/testlogs/omap-hwmod-b-for-v4.6/20160301021258/
Add hwmod data for the eDMA blocks:
- TPCC: Third-party channel controller
- TPTC0: Third-party transfer controller 0
- TPTC1: Third-party transfer controller 1
The TPCC's clock gating status follows the status of its clock and
power domain. This means that the hwmod code can not directly control
the TPCC enable/disable status.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
[paul@pwsan.com: rephrased last two sentences of the patch description]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Looks like we have few cases with wrong clock, and some
entries with missing clock. It should always be sysclk6
for the l4_ls instance.
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add a custom reset handler for DRA7x PCIeSS. This
handler is required to deassert PCIe hardreset lines
after they have been asserted.
This enables the PCIe driver to access registers after
PCIeSS has been runtime enabled without having to
deassert hardreset lines itself.
With this patch applied, used lspci to make sure
connected PCIe device enumerates on DRA74x and DRA72x
EVMs.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Reported-by: Richard Cochran <richardcochran@gmail.com>
Tested-by: Kishon Vijay Abraham I <kishon@ti.com>
Cc: Suman Anna <s-anna@ti.com>
Cc: Dave Gerlach <d-gerlach@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
We still have some boards booting in legacy mode and they will need to have
the device/slave -> filter_fn mapping so we can convert the OMAP drivers
to use the new dmaengine API for requesting channels.
Only some OMAP24xx and OMAP3xxx boards can boot in legacy mode which means
we only need to provide the map for these SoCs.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
If syscon_config.max_register is initialized like it should be, we have
omap_ctrl_read/write() fail with out of range register access at least
for omap3.
We have omap3.dtsi setting up a regmap range for scm_conf, but we now
have omap_ctrl_read/write() also attempt to use the regmap. However,
omap_ctrl_read/write() is also used for other register ranges in the
system control module (SCM).
Let's fix the issue by just removing the regmap_read/write() usage for
control module as suggested by Tero Kristo <t-kristo@ti.com>.
Signed-off-by: Tony Lindgren <tony@atomide.com>
A few fixes for OMAP hwmod data. SSI hwmod data for the OMAP 3730,
and some fixes for the DRA7xx hwmod data. These shouldn't interfere
or impact anything else.
Basic build, boot, and PM test logs are available here:
http://www.pwsan.com/omap/testlogs/omap-hwmod-a-for-v4.6/20160214161224/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=BCT2
-----END PGP SIGNATURE-----
Merge tag 'for-v4.6/omap-hwmod-a' of git://git.kernel.org/pub/scm/linux/kernel/git/pjw/omap-pending into omap-for-v4.6/fixes-not-urgent
ARM: OMAP2+: first set of hwmod fixes and additions for v4.6
A few fixes for OMAP hwmod data. SSI hwmod data for the OMAP 3730,
and some fixes for the DRA7xx hwmod data. These shouldn't interfere
or impact anything else.
Basic build, boot, and PM test logs are available here:
http://www.pwsan.com/omap/testlogs/omap-hwmod-a-for-v4.6/20160214161224/
Based on CPU type choose generic omap3 or omap3430 specific cpuidle
parameters. Parameters for omap3430 were measured on Nokia N900 device and
added by commit 5a1b1d3a9e ("OMAP3: RX-51: Pass cpu idle parameters")
which were later removed by commit 231900afba ("ARM: OMAP3: cpuidle -
remove rx51 cpuidle parameters table") due to huge code complexity.
This patch brings cpuidle parameters for omap3430 devices again, but uses
simple condition based on CPU type.
Fixes: 231900afba ("ARM: OMAP3: cpuidle - remove rx51 cpuidle
parameters table")
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Currently of_machine_is_compatible is used to detect the soc which
employs string comparison operations. We already have all the required
information in the omap_revision. Hence make use of the same like
the previous OMAPs and avoid costly string comparisons.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The patch registers the rtc hwmod on AM437x chips. The RTC module is
physically present on the AM438x SoC used on AM43X-EPOS-EVM, but it is
permanently disabled. A secure RTC is used instead on these devices,
where needed. Hence adding it selectively using a separate list to get
RTC Module functional on the other am43x SoCs used on am437x-gp-evm
and am437x-sk-evm.
Signed-off-by: Keerthy <j-keerthy@ti.com>
[paul@pwsan.com: cleaned up patch description]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
If a driver PM runtime is disabled via sysfs, and the module is
unloaded, PM runtime can't do anything to disable the device. Let's
let the interconnect disable the device on BUS_NOTIFY_UNBOUND_DRIVER.
Otherwise omap_device will produce and error on the following module
reload. This can be easily tested with something like:
# modprobe omap_hsmmc
# echo on > /sys/devices/platform/68000000.ocp/4809c000.mmc/power/control
# rmmod omap_hsmmc
# modprobe omap_hsmmc
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Nishanth Menon <nm@ti.com>
Cc: Rafael J. Wysocki <rafael@kernel.org>
Cc: Tero Kristo <t-kristo@ti.com>
Reported-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Kevin Hilman <khilman@baylibre.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Drivers using pm_runtime_use_autosuspend() may not get disabled after
-EPROBE_DEFER. On the following device driver probe, hardware state
is different from the PM runtime state causing omap_device to produce
the following error:
omap_device_enable() called from invalid state 1
And with omap_device and omap hardware being picky for PM, this will
block any deeper idle states in hardware.
Let's add a proper error message so driver writers can easily fix
their drivers for PM.
In general, the solution is to fix the drivers to follow the PM
runtime documentation:
1. For sections of code that needs the device disabled, use
pm_runtime_put_sync_suspend() if pm_runtime_set_autosuspend() has
been set.
2. For driver exit code, use pm_runtime_dont_use_autosuspend() before
pm_runtime_put_sync() if pm_runtime_use_autosuspend() has been
set.
Let's not return with 0 from _od_runtime_resume() as that will
eventually lead into new drivers with broken PM runtime that will
block deeper idle states on omaps.
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Nishanth Menon <nm@ti.com>
Cc: Rafael J. Wysocki <rafael@kernel.org>
Cc: Tero Kristo <t-kristo@ti.com>
Acked-by: Kevin Hilman <khilman@baylibre.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add PCIe reset data to PCIe hwmods on DRA7x.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Reviewed-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
OCP2SCP doesn't support smart idle wakeup according to
Table 26-22. OCP2SCP_SYSCONFIG in AM572x TRM [1] and
Table 26-22. OCP2SCP_SYSCONFIG in AM571x TRM [2].
Remove SIDLE_SMART_WKUP from the list of supported SIDLE modes
in hwmod data.
[1] -> http://www.ti.com/lit/ug/spruhz6e/spruhz6e.pdf
[2] -> http://www.ti.com/lit/ug/spruhz7a/spruhz7a.pdf
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
The variable "MACHINE" is empty if CONFIG_ARCH_MULTIPLATFORM=y,
so these Makefile.boot files are never included.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Michal Simek <michal.simek@xilinx.com> (for Zynq)
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
DRIVER_NAME is too generic to be used in a driver-specific platform
data file. Use a name specific to the driver instead, to avoid
collisions.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Acked-by: Tony Lindgren <tony@atomide.com>
Cc: Jiri Slaby <jslaby@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch enables Synchronous Serial Interface (SSI)
hwmod support for OMAP36xx SoCs (used by Nokia N950/N9).
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
In order to set the currently platform dependent dmtimer
functions pointers as platform data for the pwm-omap-dmtimer
platform driver, add it to plat-omap auxdata_lookup table.
Suggested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We don't want to write to .text so let's move ppa_zero_params and
ppa_por_params to .data and access them via pointers.
Note that I have not been able to test as we I don't have a HS
omap4 to test with. The code has been changed in similar way as
for omap3 though.
Cc: Kees Cook <keescook@chromium.org>
Cc: Laura Abbott <labbott@redhat.com>
Cc: Nishanth Menon <nm@ti.com>
Cc: Richard Woodruff <r-woodruff2@ti.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Tero Kristo <t-kristo@ti.com>
Acked-by: Nicolas Pitre <nico@linaro.org>
Cc: stable@vger.kernel.org # v4.0+
Fixes: 1e6b48116a ("ARM: mm: allow non-text sections to be
non-executable")
Signed-off-by: Tony Lindgren <tony@atomide.com>
We don't want to write to .text, so let's move l2_inv_api_params
to .data and access it via a pointer.
Cc: Kees Cook <keescook@chromium.org>
Cc: Laura Abbott <labbott@redhat.com>
Cc: Nishanth Menon <nm@ti.com>
Cc: Richard Woodruff <r-woodruff2@ti.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Tero Kristo <t-kristo@ti.com>
Acked-by: Nicolas Pitre <nico@linaro.org>
Cc: stable@vger.kernel.org # v4.0+
Fixes: 1e6b48116a ("ARM: mm: allow non-text sections to be
non-executable")
Signed-off-by: Tony Lindgren <tony@atomide.com>
We don't want to write to .text and we can move save_secure_ram_context
into .data as it all gets copied into SRAM anyways.
Cc: Kees Cook <keescook@chromium.org>
Cc: Laura Abbott <labbott@redhat.com>
Cc: Nishanth Menon <nm@ti.com>
Cc: Richard Woodruff <r-woodruff2@ti.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Cc: Tero Kristo <t-kristo@ti.com>
Acked-by: Nicolas Pitre <nico@linaro.org>
Cc: stable@vger.kernel.org # v4.0+
Fixes: 1e6b48116a ("ARM: mm: allow non-text sections to be
non-executable")
Signed-off-by: Tony Lindgren <tony@atomide.com>
We don't want to write to .text section. Let's move l2dis_3630
to .data and access it via a pointer.
For calculating the offset, let's optimize out the add and do it
in ldr/str as suggested by Nicolas Pitre <nicolas.pitre@linaro.org>.
Cc: Kees Cook <keescook@chromium.org>
Cc: Laura Abbott <labbott@redhat.com>
Cc: Nishanth Menon <nm@ti.com>
Cc: Richard Woodruff <r-woodruff2@ti.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Tero Kristo <t-kristo@ti.com>
Cc: stable@vger.kernel.org # v4.0+
Acked-by: Nicolas Pitre <nico@linaro.org>
Cc: stable@vger.kernel.org # v4.0+
Fixes: 1e6b48116a ("ARM: mm: allow non-text sections to be
non-executable")
Signed-off-by: Tony Lindgren <tony@atomide.com>
We don't want to be writing to .text so it can be set rodata.
Fix error "Unable to handle kernel paging request at virtual address
c012396c" in wait_dll_lock_timed if CONFIG_DEBUG_RODATA is selected.
As these counters are for debugging only and unused, we can just
remove them.
Cc: Kees Cook <keescook@chromium.org>
Cc: Laura Abbott <labbott@redhat.com>
Cc: Nishanth Menon <nm@ti.com>
Cc: Richard Woodruff <r-woodruff2@ti.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Tero Kristo <t-kristo@ti.com>
Acked-by: Nicolas Pitre <nico@linaro.org>
Cc: stable@vger.kernel.org # v4.0+
Fixes: 1e6b48116a ("ARM: mm: allow non-text sections to be
non-executable")
Signed-off-by: Tony Lindgren <tony@atomide.com>
The legacy-style mailbox device creation is supported currently
only for OMAP3, as all other SoCs are DT-boot only. Even on this
SoC, there are no client drivers that utilize these mailbox devices.
So, clean up the legacy-style mailbox device instantiation logic.
The mailbox devices are already present and supported for the DT
boot on OMAP3.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
- Modify the driver core and the USB subsystem to allow USB devices
to stay suspended over system suspend/resume cycles if they have
been runtime-suspended already beforehand and fix some bugs on
top of these changes (Tomeu Vizoso, Rafael Wysocki).
- Update ACPICA to upstream revision 20160108, including updates
of the ACPICA's copyright notices, a code fixup resulting from
a regression fix that was necessary in the upstream code only
(the regression fixed by it has never been present in Linux)
and a compiler warning fix (Bob Moore, Lv Zheng).
- Fix a recent regression in the cpuidle menu governor that broke
it on practically all architectures other than x86 and make a
couple of optimizations on top of that fix (Rafael Wysocki).
- Clean up the selection of cpuidle governors depending on whether
or not the kernel is configured for tickless systems (Jean Delvare).
- Revert a recent commit that introduced a regression in the ACPI
backlight driver, address the problem it attempted to fix in a
different way and revert one more cosmetic change depending on
the problematic commit (Hans de Goede).
- Add two more ACPI backlight quirks (Hans de Goede).
- Fix a few minor problems in the core devfreq code, clean it up
a bit and update the MAINTAINERS information related to it
(Chanwoo Choi, MyungJoo Ham).
- Improve an error message in the ACPI fan driver (Andy Lutomirski).
- Fix a recent build regression in the cpupower tool (Shreyas Prabhu).
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=bKJ9
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-4.5-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull more power management and ACPI updates from Rafael Wysocki:
"This includes fixes on top of the previous batch of PM+ACPI updates
and some new material as well.
From the new material perspective the most significant are the driver
core changes that should allow USB devices to stay suspended over
system suspend/resume cycles if they have been runtime-suspended
already beforehand. Apart from that, ACPICA is updated to upstream
revision 20160108 (cosmetic mostly, but including one fixup on top of
the previous ACPICA update) and there are some devfreq updates the
didn't make it before (due to timing).
A few recent regressions are fixed, most importantly in the cpuidle
menu governor and in the ACPI backlight driver and some x86 platform
drivers depending on it.
Some more bugs are fixed and cleanups are made on top of that.
Specifics:
- Modify the driver core and the USB subsystem to allow USB devices
to stay suspended over system suspend/resume cycles if they have
been runtime-suspended already beforehand and fix some bugs on top
of these changes (Tomeu Vizoso, Rafael Wysocki).
- Update ACPICA to upstream revision 20160108, including updates of
the ACPICA's copyright notices, a code fixup resulting from a
regression fix that was necessary in the upstream code only (the
regression fixed by it has never been present in Linux) and a
compiler warning fix (Bob Moore, Lv Zheng).
- Fix a recent regression in the cpuidle menu governor that broke it
on practically all architectures other than x86 and make a couple
of optimizations on top of that fix (Rafael Wysocki).
- Clean up the selection of cpuidle governors depending on whether or
not the kernel is configured for tickless systems (Jean Delvare).
- Revert a recent commit that introduced a regression in the ACPI
backlight driver, address the problem it attempted to fix in a
different way and revert one more cosmetic change depending on the
problematic commit (Hans de Goede).
- Add two more ACPI backlight quirks (Hans de Goede).
- Fix a few minor problems in the core devfreq code, clean it up a
bit and update the MAINTAINERS information related to it (Chanwoo
Choi, MyungJoo Ham).
- Improve an error message in the ACPI fan driver (Andy Lutomirski).
- Fix a recent build regression in the cpupower tool (Shreyas
Prabhu)"
* tag 'pm+acpi-4.5-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (32 commits)
cpuidle: menu: Avoid pointless checks in menu_select()
sched / idle: Drop default_idle_call() fallback from call_cpuidle()
cpupower: Fix build error in cpufreq-info
cpuidle: Don't enable all governors by default
cpuidle: Default to ladder governor on ticking systems
time: nohz: Expose tick_nohz_enabled
ACPICA: Update version to 20160108
ACPICA: Silence a -Wbad-function-cast warning when acpi_uintptr_t is 'uintptr_t'
ACPICA: Additional 2016 copyright changes
ACPICA: Reduce regression fix divergence from upstream ACPICA
ACPI / video: Add disable_backlight_sysfs_if quirk for the Toshiba Satellite R830
ACPI / video: Revert "thinkpad_acpi: Use acpi_video_handles_brightness_key_presses()"
ACPI / video: Document acpi_video_handles_brightness_key_presses() a bit
ACPI / video: Fix using an uninitialized mutex / list_head in acpi_video_handles_brightness_key_presses()
ACPI / video: Revert "ACPI / video: driver must be registered before checking for keypresses"
ACPI / fan: Improve acpi_device_update_power error message
ACPI / video: Add disable_backlight_sysfs_if quirk for the Toshiba Portege R700
cpuidle: menu: Fix menu_select() for CPUIDLE_DRIVER_STATE_START == 0
MAINTAINERS: Add devfreq-event entry
MAINTAINERS: Add missing git repository and directory for devfreq
...
As usual, the bulk of this release is again DT file contents.
There's a huge number of changes here, and it's challenging to give a crisp
overview of just what is in here. To start with:
New boards:
- TI-based DM3730 from LogicPD (Torpedo)
- Cosmic+ M4 (nommu) initial support (Freescale Vybrid)
- Raspberry Pi 2 DT files
- Watchdog on Meson8b
- Veyron-mickey (ASUS Chromebit) DTS
- Rockchip rk3228 SoC and eval board
- Sigma Designs Tango4
Improvements:
- Improved support for Qualcomm APQ8084, including Sony Xperia Z DT files
- Misc new devices for Rockchip rk3036 and rk3288
- Allwinner updates for misc SoCs and systems
... and a _large_ number of other changes across the field. Devices
added to SoC DTSI and board DTS files for a number of SoC vendors, new
product boards on already-supported SoCs, cleanups and refactorings of
existing DTS/DTSI files and a bunch of other changes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJWnr6fAAoJEIwa5zzehBx3p+gP+wYLUqXjCYgyu6oJPxJbWghj
gPc4QJmhVlAWTqvE7Ut7RumWzGa7nUEH2QF9tiCLbDAw8727HJXhRHknFwaCsX45
BsvFQaKY99ClfUhoSI9GRa8e2jEArjzEPqkynHW/8FM20qWaj/Z8DDfixG75gR8u
onrMw6kprNGwmyQwqu5zLDXhUBCQIs1xRRSabUjV1P5420dbBaGgtmQrdj7k+JDt
wo9SKiG6d9CSYil3r7BC+0JwzbKNBxRGs2vv1BJOfbZ3Lj+uC0vj1AxoF/p7dOHy
ohuvt7UwwtoUzzFMcMUo7E8qxl9u6bbnPDlUoRF7DVVi5SQoeZd8BOZXOdLRN2OQ
qtgsmziDxtvh7Ydj6i89D69x7+GurAFcP8Aturprc5Zd5lO70PAYBD379IhIZ8y1
MVJltIEeuUZo7BaVBCHWQY9jJRtI3bAU6JdFPrFROsuo810IYd72Wbb1ZCfF7SV7
nBRvV7e71VQxb48c3p8Et5FntHuXfUlhkMrQ7Cb+2ugB/diGgZB9NfrZbP3Azv7f
A5Ey9tNHaOCUxzYDCw80jTa7OwVWNJf2kOT1yikASk3vODKLv4E5YQ2DULnObWG7
iRmLYuuGka4sMs0ZjpV3kaqs+8rWu08x2rEr5X0wfU+DalIzUWA2oDKSgPLJoacV
gXKP039CIxQAiottcppA
=XDLa
-----END PGP SIGNATURE-----
Merge tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM DT updates from Olof Johansson:
"As usual, the bulk of this release is again DT file contents.
There's a huge number of changes here, and it's challenging to give a
crisp overview of just what is in here. To start with:
New boards:
- TI-based DM3730 from LogicPD (Torpedo)
- Cosmic+ M4 (nommu) initial support (Freescale Vybrid)
- Raspberry Pi 2 DT files
- Watchdog on Meson8b
- Veyron-mickey (ASUS Chromebit) DTS
- Rockchip rk3228 SoC and eval board
- Sigma Designs Tango4
Improvements:
- Improved support for Qualcomm APQ8084, including Sony Xperia Z DT files
- Misc new devices for Rockchip rk3036 and rk3288
- Allwinner updates for misc SoCs and systems
... and a _large_ number of other changes across the field. Devices
added to SoC DTSI and board DTS files for a number of SoC vendors, new
product boards on already-supported SoCs, cleanups and refactorings of
existing DTS/DTSI files and a bunch of other changes"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (469 commits)
ARM: dts: compulab: add new board description
ARM: versatile: add the syscon LEDs to the DT
dts: vt8500: Fix errors in SDHC node for WM8505
ARM: dts: imx6q: clean up unused ipu2grp
ARM: dts: silk: Add compatible property to "partitions" node
ARM: dts: gose: Add compatible property to "partitions" node
ARM: dts: porter: Add compatible property to "partitions" node
ARM: dts: koelsch: Add compatible property to "partitions" node
ARM: dts: lager: Add compatible property to "partitions" node
ARM: dts: bockw: Add compatible property to "partitions" node
ARM: dts: meson8b: Add watchdog node
Documentation: watchdog: Add new bindings for meson8b
ARM: meson: Add status LED for Odroid-C1
ARM: dts: uniphier: fix a typo in comment block
ARM: bcm2835: Add the auxiliary clocks to the device tree.
ARM: bcm2835: Add devicetree for bcm2836 and Raspberry Pi 2 B
ARM: bcm2835: Move the CPU/peripheral include out of common RPi DT.
ARM: bcm2835: Split the DT for peripherals from the DT for the CPU
ARM: realview: set up cache correctly on the PB11MPCore
ARM: dts: Unify G2D device node with other devices on exynos4
...
Updates for new platform support:
- New platform: Tango4 from Sigma Designs.
- Broadcom BCM2836 (Raspberry Pi 2 SoC)
- Enable cpufreq on Freescale i.MX7D
- Rockchip: SMP support for rk3036, general support for rk3228
- SMP support on Broadcom Kona and NSP
- Cleanups for OMAP removing legacy IOMMU data
+ a bunch of misc fixes and tweaks for various platforms.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=FP4V
-----END PGP SIGNATURE-----
Merge tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC platform updates from Olof Johansson:
"Updates for new platform support:
- New platform: Tango4 from Sigma Designs.
- Broadcom BCM2836 (Raspberry Pi 2 SoC)
- Enable cpufreq on Freescale i.MX7D
- Rockchip: SMP support for rk3036, general support for rk3228
- SMP support on Broadcom Kona and NSP
- Cleanups for OMAP removing legacy IOMMU data
+ a bunch of misc fixes and tweaks for various platforms"
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (46 commits)
ARM: tango: Fix UP build issues
ARM: tango: pass ARM arch level for smc.S
ARM: bcm2835: Add Kconfig support for bcm2836
ARM: OMAP2+: Add support for dm814x and dra62x usb
ARM: OMAP2+: Add mmc hwmod entries for dm814x
ARM: OMAP2+: Update 81xx clock and power domains for default, active and sgx
ARM: OMAP2+: Fix SoC detection for dra62x j5-eco
ARM: tango4: Initial platform support
ARM: bcm2835: Add a compat string for bcm2836 machine probe
dt-bindings: Add root properties for Raspberry Pi 2
ARM: imx: select SRC for i.MX7
ARM: uniphier: select PINCTRL
ARM: OMAP2+: Remove device creation for omap-pcm-audio
ARM: OMAP1: Remove device creation for omap-pcm-audio
ARM: rockchip: enable support for RK3228 SoCs
ARM: rockchip: use const and __initconst for rk3036 smp_operations
ARM: zynq: Select ARCH_HAS_RESET_CONTROLLER
ARM: BCM: Add SMP support for Broadcom 4708
ARM: BCM: Add SMP support for Broadcom NSP
ARM: BCM: Clean up SMP support for Broadcom Kona
...
A smallish number of general cleanup commits this release cycle. Some
of these are minor tweaks:
- shmobile change of binding for their GIC (using arm,pl390 now)
- ARCH_RENESAS introduction
- Misc other renesas updates
There's also a couple of treewide commits from Masahiro Yamada cleaning up
const/__initconst for SMP operation structs and a switch to using "depends
on" instead of if-constructs on most of the Kconfig platform targets.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=pQaP
-----END PGP SIGNATURE-----
Merge tag 'armsoc-cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC cleanups from Olof Johansson:
"A smallish number of general cleanup commits this release cycle. Some
of these are minor tweaks:
- shmobile change of binding for their GIC (using arm,pl390 now)
- ARCH_RENESAS introduction
- Misc other renesas updates
There's also a couple of treewide commits from Masahiro Yamada
cleaning up const/__initconst for SMP operation structs and a switch
to using "depends on" instead of if-constructs on most of the Kconfig
platform targets"
* tag 'armsoc-cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
staging: board: armadillo800eva: Use "arm,pl390"
staging: board: kzm9d: Use "arm,pl390"
ARM: shmobile: r8a7778 dtsi: Use "arm,pl390" for GIC
ARM: shmobile: emev2 dtsi: Use "arm,pl390" for GIC
ARM: shmobile: r8a7740 dtsi: Use "arm,pl390" for GIC
ARM: shmobile: r7s72100 dtsi: Use "arm,pl390" for GIC
ARM: use "depends on" for SoC configs instead of "if" after prompt
ARM/clocksource: use automatic DT probing for ux500 PRCMU
ARM: use const and __initconst for smp_operations
ARM: hisi: do not export smp_operations structures
ARM: mvebu: remove unused mach/gpio.h
ARM: shmobile: Remove legacy mach/irqs.h
ARM: shmobile: Introduce ARCH_RENESAS
MAINTAINERS: Remove link to oss.renesas.com which is closed
As usual, we queue up a few fixes that don't seem urgent enough to go in
through -rc.
- MAINTAINERS updates to add a list for brcmstb and fix a typo
- A handful of fixes for OMAP 81xx, a recently resurrected platform so these
can't be considered real regressions and thus got queued.
- A couple of other small fixes for scoop, sa1100 and davinci
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=W+es
-----END PGP SIGNATURE-----
Merge tag 'armsoc-fixes-nc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull non-urgent ARM SoC fixes from Olof Johansson:
"As usual, we queue up a few fixes that don't seem urgent enough to go
in through -rc.
- MAINTAINERS updates to add a list for brcmstb and fix a typo
- A handful of fixes for OMAP 81xx, a recently resurrected platform
so these can't be considered real regressions and thus got queued.
- A couple of other small fixes for scoop, sa1100 and davinci"
* tag 'armsoc-fixes-nc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: OMAP2+: Fix randconfig build warning for dm814_pllss_data
ARM: sa1100/simpad: Be sure to clamp return value
ARM: scoop: Be sure to clamp return value
ARM: davinci: fix a problematic usage of WARN()
ARM: davinci: only select WT cache if cache is enabled
ARM: OMAP2+: Remove useless check for legacy booting for dm814x
ARM: OMAP2+: Enable GPIO for dm814x
ARM: dts: Fix dm814x pinctrl address and mask
ARM: dts: Fix dm8148 control modules ranges
ARM: OMAP2+: Fix timer entries for dm814x
ARM: dts: Fix some mux and divider clocks to get dm814x-evm booting
ARM: OMAP2+: Add DPPLS clock manager for dm814x
clk: ti: Add few dm814x clock aliases
ARM: dts: Fix dm814x entries for pllss and prcm
MAINTAINERS: gpio-brcmstb: Remove stray '>'
MAINTAINERS: brcmstb: Include Broadcom internal mailing-list
* pm-core:
driver core: Avoid NULL pointer dereferences in device_is_bound()
platform: Do not detach from PM domains on shutdown
USB / PM: Allow USB devices to remain runtime-suspended when sleeping
PM / sleep: Go direct_complete if driver has no callbacks
PM / Domains: add setter for dev.pm_domain
device core: add device_is_bound()
bulk of the changes are to clk controller drivers, though some
improvements to the core and some re-usable blocks/templates also
received some love. In this past cycle the clk maintainers developed a
good workflow for handling the common case of patch submissions
containing a new drivers, new shared Device Tree header and a new Device
Tree binding description. This requires coordination with the Device
Tree maintainers and with the architecture maintainers (typically the
arm-soc tree in our case). This explains the increase in changes to
include/dt-bindings/... and to
Documentation/devicetree/bindings/clock/... coming from the clk tree.
The same commits can be expected to come through those trees on
occasion, through the use of shared, immutable branches.
-----BEGIN PGP SIGNATURE-----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=nkGr
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus-4.5' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk framework updates from Michael Turquette:
"The clk framework and driver changes for 4.5 look pretty typical. The
bulk of the changes are to clk controller drivers, though some
improvements to the core and some re-usable blocks/templates also
received some love.
In this past cycle the clk maintainers developed a good workflow for
handling the common case of patch submissions containing a new
drivers, new shared Device Tree header and a new Device Tree binding
description. This requires coordination with the Device Tree
maintainers and with the architecture maintainers (typically the
arm-soc tree in our case).
This explains the increase in changes to include/dt-bindings/... and
to Documentation/devicetree/bindings/clock/... coming from the clk
tree. The same commits can be expected to come through those trees on
occasion, through the use of shared, immutable branches"
* tag 'clk-for-linus-4.5' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (125 commits)
clk: remove duplicated COMMON_CLK_NXP record from clk/Kconfig
clk: fix clk-gpio.c with optional clock= DT property
clk: rockchip: fix section mismatches with new child-clocks
clk: gpio: handle error codes for of_clk_get_parent_count()
clk: gpio: fix memory leak
clk: shmobile: r8a7795: Add SATA0 clock
clk: bcm2835: Add PWM clock support
clk: bcm2835: Support for clock parent selection
clk: bcm2835: add a round up ability to the clock divisor
clk: lpc32xx: add common clock framework driver
clk: lpc18xx: add NXP specific COMMON_CLK_NXP configuration symbol
dt-bindings: clock: add NXP LPC32xx clock list for consumers
dt-bindings: clock: add description of LPC32xx USB clock controller
dt-bindings: clock: add description of LPC32xx clock controller
clk: rockchip: rk3036: include downstream muxes into fractional dividers
clk: add flag for clocks that need to be enabled on rate changes
clk: rockchip: Allow the RK3288 SPDIF clocks to change their parent
clk: rockchip: include downstream muxes into fractional dividers
clk: rockchip: handle mux dependency of fractional dividers
clk: bcm2835: Add a driver for the auxiliary peripheral clock gates.
...
Pull ARM updates from Russell King:
- UEFI boot and runtime services support for ARM from Ard Biesheuvel
and Roy Franz.
- DT compatibility with old atags booting protocol for Nokia N900
devices from Ivaylo Dimitrov.
- PSCI firmware interface using new arm-smc calling convention from
Jens Wiklander.
- Runtime patching for udiv/sdiv instructions for ARMv7 CPUs that
support these instructions from Nicolas Pitre.
- L2x0 cache updates from Dirk B and Linus Walleij.
- Randconfig fixes from Arnd Bergmann.
- ARMv7M (nommu) updates from Ezequiel Garcia
* 'for-linus' of git://ftp.arm.linux.org.uk/~rmk/linux-arm: (34 commits)
ARM: 8481/2: drivers: psci: replace psci firmware calls
ARM: 8480/2: arm64: add implementation for arm-smccc
ARM: 8479/2: add implementation for arm-smccc
ARM: 8478/2: arm/arm64: add arm-smccc
ARM: 8494/1: mm: Enable PXN when running non-LPAE kernel on LPAE processor
ARM: 8496/1: OMAP: RX51: save ATAGS data in the early boot stage
ARM: 8495/1: ATAGS: move save_atags() to arch/arm/include/asm/setup.h
ARM: 8452/3: PJ4: make coprocessor access sequences buildable in Thumb2 mode
ARM: 8482/1: l2x0: make it possible to disable outer sync from DT
ARM: 8488/1: Make IPI_CPU_BACKTRACE a "non-secure" SGI
ARM: 8487/1: Remove IPI_CALL_FUNC_SINGLE
ARM: 8485/1: cpuidle: remove cpu parameter from the cpuidle_ops suspend hook
ARM: 8484/1: Documentation: l2c2x0: Mention separate controllers explicitly
ARM: 8483/1: Documentation: l2c: Rename l2cc to l2c2x0
ARM: 8477/1: runtime patch udiv/sdiv instructions into __aeabi_{u}idiv()
ARM: 8476/1: VDSO: use PTR_ERR_OR_ZERO for vma check
ARM: 8453/2: proc-v7.S: don't locate temporary stack space in .text section
ARM: add UEFI stub support
ARM: wire up UEFI init and runtime support
ARM: only consider memblocks with NOMAP cleared for linear mapping
...
* patchwork: (204 commits)
[media] rc: sunxi-cir: Initialize the spinlock properly
[media] rtl2832: do not filter out slave TS null packets
[media] rtl2832: print reg number on error case
[media] rtl28xxu: return demod reg page from driver cache
[media] coda: enable MPEG-2 ES decoding
[media] coda: don't start streaming without queued buffers
[media] coda: hook up vidioc_prepare_buf
[media] coda: relax coda_jpeg_check_buffer for trailing bytes
[media] coda: make to_coda_video_device static
[media] s5p-mfc: remove volatile attribute from MFC register addresses
[media] s5p-mfc: merge together s5p_mfc_hw_call and s5p_mfc_hw_call_void
[media] s5p-mfc: use spinlock to protect MFC context
[media] s5p-mfc: remove unnecessary callbacks
[media] s5p-mfc: make queue cleanup code common
[media] s5p-mfc: use one implementation of s5p_mfc_get_new_ctx
[media] s5p-mfc: constify s5p_mfc_codec_ops structures
[media] au8522: Avoid memory leak for device config data
[media] ir-lirc-codec.c: don't leak lirc->drv-rbuf
[media] uvcvideo: small cleanup in uvc_video_clock_update()
[media] uvcvideo: Fix reading the current exposure value of UVC
...
Adds a function that sets the pointer to dev_pm_domain in struct device
and that warns if the device has already finished probing. The reason
why we want to enforce that is because in the general case that can
cause problems and also that we can simplify code quite a bit if we can
always assume that.
This patch also changes all current code that directly sets the
dev.pm_domain pointer.
Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Commit 63aa945b10 ("memory: omap-gpmc: Add Kconfig option for debug")
unified the GPMC debug for the SoCs with GPMC. The commit also left out
the option for HWMOD_INIT_NO_RESET as we now require proper timings for
GPMC to be able to remap GPMC devices out of address 0.
Unfortunately on Nokia N900, onenand now only partially works with the
device tree provided timings. It works enough to get detected but the
clock rate supported by the onenand chip gets misdetected. This in turn
causes the GPMC timings to be miscalculated and this leads into file
system corruption on N900.
Looks like onenand needs CS_CONFIG1 bit 27 WRITETYPE set for for sync
write. This is needed also for async timings when we write to onenand
with omap2_onenand_set_async_mode(). Without sync write bit set, the
async read for the onenand ONENAND_REG_VERSION_ID will return 0xfff.
Let's exit with an error if onenand rate is not detected. And let's
remove the extra call to omap2_onenand_set_async_mode() as we only need
to do this once at the end of omap2_onenand_setup_async().
Fixes: 63aa945b10 ("memory: omap-gpmc: Add Kconfig option for debug")
Cc: stable@vger.kernel.org # v4.2+
Reported-by: Ivaylo Dimitrov <ivo.g.dimitrov.75@gmail.com>
Tested-by: Ivaylo Dimitrov <ivo.g.dimitrov.75@gmail.com>
Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This fixes a regression with device tree based booting compared to legacy booting for n900 to make the n900 legacy user space to also work with device tree based booting
Signed-off-by: Ivaylo Dimitrov <ivo.g.dimitrov.75@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Pull "reworked soc changes for ti81xx devices and minimal dra62x
j5ec-evm support" from Tony Lindgren:
Add minimal SoC support for dra62x also known as j5eco. As it's closely
related to dm814x, we can treat it as a dm814x variant for now and do
rest of the configuration with DTS just files. And let's add hwmod
support for MMC and USB on dm814x and dra62x.
* tag 'omap-for-v4.5/81xx-soc-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: Add support for dm814x and dra62x usb
ARM: OMAP2+: Add mmc hwmod entries for dm814x
ARM: OMAP2+: Update 81xx clock and power domains for default, active and sgx
ARM: OMAP2+: Fix SoC detection for dra62x j5-eco
related to dm814x, just the clocks are a bit different and it has a
different set of integrated devices. And let's get some basic dm814x
and dra62x devices working as many of the devices are like on am33xx::
- pinctrl using the pinctrl defines as for am33xx
- Updated EDMA bindings with support for using exma_xbar
- MMC support for dm814x-evm, t410 and dra62x-j5eco-evm
- USB support for dm814x-evm, t410 and dra62x-j5eco-evm
This branch depends on an earlier omap-for-v4.5/81xx-fixes-signed
branch that has dm814x dts fixes interlaced with SoC related fixes to
keep things booting. The interlaced SoC and dts fixes were needed
because of issues with the device tree defined clocks that just
happened to work on bootloader timings for t410 earlier.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=W/MF
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.5/81xx-dts-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/dt
Pull "reworked dts changes for ti81xx devices and minimal
dra62x j5ec-evm support" from Tony Lindgren:
Add minimal device tree support for dra62x also known j5eco. It is
related to dm814x, just the clocks are a bit different and it has a
different set of integrated devices. And let's get some basic dm814x
and dra62x devices working as many of the devices are like on am33xx::
- pinctrl using the pinctrl defines as for am33xx
- Updated EDMA bindings with support for using exma_xbar
- MMC support for dm814x-evm, t410 and dra62x-j5eco-evm
- USB support for dm814x-evm, t410 and dra62x-j5eco-evm
This branch depends on an earlier omap-for-v4.5/81xx-fixes-signed
branch that has dm814x dts fixes interlaced with SoC related fixes to
keep things booting. The interlaced SoC and dts fixes were needed
because of issues with the device tree defined clocks that just
happened to work on bootloader timings for t410 earlier.
* tag 'omap-for-v4.5/81xx-dts-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (21 commits)
ARM: dts: Add usb support for j5-eco evm
ARM: dts: Add usb support for hp t410
ARM: dts: Add usb support for dm814x-evm
ARM: dts: Add usb support for dm814x and dra62x
ARM: dts: Enable emmc on hp t410
ARM: dts: Add mmc support for dra62x j5-eco evm
ARM: dts: Add mmc support for dm8148-evm
ARM: dts: Add mmc device entries for dm814x
ARM: dts: Update edma bindings on dm814x to use edma_xbar
ARM: dts: Add pinctrl macros for dm814x
ARM: dts: Add minimal dra62x j5-eco evm support
ARM: dts: Add basic support for dra62x j5-eco SoC
ARM: OMAP2+: Remove useless check for legacy booting for dm814x
ARM: OMAP2+: Enable GPIO for dm814x
ARM: dts: Fix dm814x pinctrl address and mask
ARM: dts: Fix dm8148 control modules ranges
ARM: OMAP2+: Fix timer entries for dm814x
ARM: dts: Fix some mux and divider clocks to get dm814x-evm booting
ARM: OMAP2+: Add DPPLS clock manager for dm814x
clk: ti: Add few dm814x clock aliases
...
Fix warning for arch/arm/mach-omap2/prm_common.c:666:35: warning:
‘dm814_pllss_data’ defined but not used [-Wunused-variable]".
This can happen if CONFIG_SOC_TI81XX is not selected.
Signed-off-by: Tony Lindgren <tony@atomide.com>
The usb phys are different on dm814x compared to dm816x so we need to
use the clkdcoldo output for usb.
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Let's add mmc entries for dm814x. To do that, we need to rename some
entries to be common for 81xx.
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
These offsets seem to be common, so let's rename the defines. And let's
set up the default_l3_slow_81xx_clkdm with active and default powerdomains
for dm814x. These are needed for usb to work.
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can boot dra62x j5-eco using the dm814x code as the clocks and
devices are mapped in the device tree. The dra62x is also known
as jacinto 5 eco.
We may want to add separate soc_is macros for dra62x if needed,
but this gets us to the point where we can boot dra62x with just
dts changes.
Let's also print out the unknown hawkeye register to make things
a bit easier for new SoC variants.
Signed-off-by: Tony Lindgren <tony@atomide.com>
updates the EDMA bindings based on the various fixes to split EDMA into
separate independent devices. It also adds support for more devices on the
CompuLab cm-t335 and LogicPD Torpedo boards, and enables the new bindings
for qspi for am437x and dra7. There are also few dra7 regulator fixes, and
change of gpoi-key,wakeup to wakeup-source.
These depend on commit ae0add740c ("dmaengine: edma: DT: Change reserved
slot array from 16bit to 32bit type") already merged into mainline.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=+G24
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.5/dt-pt2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/dt
Second set of omap device tree changes for v4.5 merge window. This series
updates the EDMA bindings based on the various fixes to split EDMA into
separate independent devices. It also adds support for more devices on the
CompuLab cm-t335 and LogicPD Torpedo boards, and enables the new bindings
for qspi for am437x and dra7. There are also few dra7 regulator fixes, and
change of gpoi-key,wakeup to wakeup-source.
These depend on commit ae0add740c ("dmaengine: edma: DT: Change reserved
slot array from 16bit to 32bit type") already merged into mainline.
* tag 'omap-for-v4.5/dt-pt2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: LogicPD Torpedo: Add Touchscreen Support
ARM: dts: DRA7-EVM: Add regulator-allow-bypass property for ldo9
ARM: dts: DRA72-EVM: Add regulator-allow-bypass property for ldo1 and ldo2
ARM: dts: AM4372: add entry for qspi mmap region
ARM: dts: DRA7: add entry for qspi mmap region
ARM: OMAP2+: LogicPD Torpedo: Revert Duplicative Entries
ARM: OMAP2+: LogicPD Torpedo + Wireless: Add Bluetooth
ARM: OMAP2+: LogicPD Torpedo: Add LCD Type 15 Support
ARM: dts: cm-t335: add support for bluetooth
ARM: dts: cm-t335: add support for DVI/LCD
ARM: dts: cm-t335: add support for I2C GPIO expander
ARM: dts: cm-t335: add support for SBC-T335
ARM: dts: cm-t335: add support for USB0
ARM: dts: omap: replace legacy *,wakeup property with wakeup-source
ARM: dts: am335x: replace gpio-key,wakeup with wakeup-source property
ARM: DTS: am437x: Use the new DT bindings for the eDMA3
ARM: DTS: am33xx: Use the new DT bindings for the eDMA3
dmaengine: edma: DT: Change reserved slot array from 16bit to 32bit type
dmaengine: edma: DT: Change memcpy channel array from 16bit to 32bit type
Signed-off-by: Olof Johansson <olof@lixom.net>
change the omap initcall levels a bit to initialize things later to allow
early device drivers at core_initcall level. This makes things easier
for us as most clocks can be made into regular device drivers except for
a few early clocks needed to initialize system timers. I wanted to have
these changes sit in Linux next for a few weeks before sending out a pull
request, and so far now issues have showed up.
The other changes in this series are timer changes for making use of the
new PWM driver, and timer changes to support more high security SoCs.
Also few minor improvments for module autoidle settings for ti81xx spinbox
and dra7 debug on uart4 in hwmod code. The rest is pretty much just removal
of platform data for SoCs that are all device tree only nowadays.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=69mE
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.5/soc-initcall' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/soc
SoC changes for omaps for v4.5 merge window. The main change here is to
change the omap initcall levels a bit to initialize things later to allow
early device drivers at core_initcall level. This makes things easier
for us as most clocks can be made into regular device drivers except for
a few early clocks needed to initialize system timers. I wanted to have
these changes sit in Linux next for a few weeks before sending out a pull
request, and so far now issues have showed up.
The other changes in this series are timer changes for making use of the
new PWM driver, and timer changes to support more high security SoCs.
Also few minor improvments for module autoidle settings for ti81xx spinbox
and dra7 debug on uart4 in hwmod code. The rest is pretty much just removal
of platform data for SoCs that are all device tree only nowadays.
* tag 'omap-for-v4.5/soc-initcall' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: Remove device creation for omap-pcm-audio
ARM: OMAP1: Remove device creation for omap-pcm-audio
ARM: OMAP2+: Change core_initcall levels to postcore_initcall
ARM: DRA7: hwmod: Enable DEBUG_LL for UART4
ARM: OMAP: RX-51: fix a typo in log writing
ARM: omap4: hwmod: Remove elm address space from hwmod data
ARM: OMAP2+: timer: Remove secure timer for DRA7xx HS devices
ARM: OMAP: dmtimer: check for fixed timers during config
ARM: OMAP2+: Remove omap_mmu_dev_attr structure
ARM: OMAP4: hwmod data: Remove legacy IOMMU attr and addrs
ARM: OMAP3: hwmod data: Remove legacy IOMMU data
ARM: OMAP2+: Remove legacy device instantiation of IOMMUs
ARM: OMAP2+: Add hwmod spinbox support for dm816x
ARM: OMAP: add DT support for ti,dm816-timer
ARM: OMAP: dmtimer: Add clock source from DT
Signed-off-by: Olof Johansson <olof@lixom.net>
Make sure to tell the kernel that AM437x devices have ARM TWD timer.
Signed-off-by: Felipe Balbi <balbi@ti.com>
[grygorii.strashko@ti.com: drop ARM Global timer selection, because
it's incompatible with PM (cpuidle/cpufreq). So, it's unsafe to enable
it unconditionally]
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
System will misbehave in the following case:
- AM43XX only build (UP);
- CONFIG_CPU_IDLE=y
- ARM TWD timer enabled and selected as clockevent device.
In the above case, It's expected that broadcast timer will be used as
backup timer when CPUIdle will put MPU in low power states where ARM
TWD will stop and lose its context. But, the CONFIG_SMP might not be
selected when kernel is built for AM43XX SoC only and, as result,
GENERIC_CLOCKEVENTS_BROADCAST option will not be selected also. This
will break CPUIdle and System will stuck in low power states.
Hence, fix it by selecting GENERIC_CLOCKEVENTS_BROADCAST option for
AM43XX SoCs always and add empty tick_broadcast() function
implementation - no need to send any IPI on UP. After this change
timer1 will be selected as broadcast timer the same way as for SMP,
and CPUIdle will work properly.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The omap-pcm in ASoC is no longer a platform device. No need to create this
device anymore.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Bindings for the WL1283 Bluetooth was removed from the shared transport
driver in commit c0bd1b9e58 ("Revert ti-st: add device tree support")
Until we havea better binding, we need to use the platform data to
initialize Bluetooth.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
in mainline kernel with it's bootloader configured clocks. However,
trying to boot dm814x-evm uncovered all kind of issues with the timer
clock. To keep t410 booting, these issues need to be fixed in a specific
order and this branch contains both device tree and code changes.
To summarize the changes, we had missing ranges for clocks to probe,
missing aliase for clocks, wrong registers for divder clocks, and bad
address for the control module. All these went unnoticed earlier as
things worked without errors by luck and I did not pay much attention
to them until I got hold of a dm814x-evm and I noticed it did not boot.
As these are fixes for features that never worked, these can wait for
v4.5 merge window no problem.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Mesm
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.5/81xx-fixes-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/fixes-non-critical
Merge "omap fixes for 81xx for v4.5 merge window" from Tony Lindgren:
Fixes for ti81xx for v4.5 merge window. We have hp t410 already booting
in mainline kernel with it's bootloader configured clocks. However,
trying to boot dm814x-evm uncovered all kind of issues with the timer
clock. To keep t410 booting, these issues need to be fixed in a specific
order and this branch contains both device tree and code changes.
To summarize the changes, we had missing ranges for clocks to probe,
missing aliase for clocks, wrong registers for divder clocks, and bad
address for the control module. All these went unnoticed earlier as
things worked without errors by luck and I did not pay much attention
to them until I got hold of a dm814x-evm and I noticed it did not boot.
As these are fixes for features that never worked, these can wait for
v4.5 merge window no problem.
* tag 'omap-for-v4.5/81xx-fixes-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: Remove useless check for legacy booting for dm814x
ARM: OMAP2+: Enable GPIO for dm814x
ARM: dts: Fix dm814x pinctrl address and mask
ARM: dts: Fix dm8148 control modules ranges
ARM: OMAP2+: Fix timer entries for dm814x
ARM: dts: Fix some mux and divider clocks to get dm814x-evm booting
ARM: OMAP2+: Add DPPLS clock manager for dm814x
clk: ti: Add few dm814x clock aliases
ARM: dts: Fix dm814x entries for pllss and prcm
We have never had dm814x booting properly with mainline kernel using
the legacy platform data based booting. Current minimal support is
device tree only.
Signed-off-by: Tony Lindgren <tony@atomide.com>
There's a mux after the oscillator similar to am335x. I did not
notice this on hp t410 as it boots even with no clocks configured.
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
On dm814x we have some clocks at DPLLS and some at PRCM. Let's add a new
omap_prcm_init_data entry for the DPLLS so we can initalize timer clocks
early.
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We want to be able to probe a few selected device drivers before hwmod
code populates the clocks in omap_hwmod_setup_all(). This allows us to
convert most of the clock drivers into regular device drivers.
We only need a few minimal clock drivers early for the system timers to
select between the 32KiHz clock and the high frequency oscillator.
With these changes, initializing the clock drivers can be just done at
core_initcall time with something like:
np = of_find_node_by_name(NULL, "plls");
if (np)
of_platform_populate(np, NULL, NULL, NULL);
And then these clocks will be available for the interconnect code to use.
Having most of the clock drivers being regular device drivers allows
us to use the nice things like devm_* functions and dev_err and dev_dbg.
As an extra bonus, this also allows us to develop the clock drivers for
new SoCs as loadable modules initially for cases where we can boot up
the system based on the bootloader configured clocks.
To do this, let's change the core_initcalls to postcore_initcall under
mach-omap2.
Cc: Felipe Balbi <balbi@ti.com>
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Enable REGULATOR_FIXED_VOLTAGE for all OMAP2+ platforms
otherwise system can't boot from SD-card when kernel is
built for single SoC (for example, with CONFIG_SOC_DRA7XX=y only).
It's also required for almost all TI SoC's platforms.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
UART4 low level debug support. This helps in debugging with UART4
serial console output on DRA7 based platforms.
Extending the following fix for UART4.
commit 1c7e36bfc3 ("ARM: DRA7: hwmod: Fix boot crash with DEBUG_LL enabled on UART3")
For using DEBUG_LL, enable CONFIG_DEBUG_OMAP4UART4 in menuconfig.
On DRA7, UART4 hwmod doesn't have this flag enabled,
failure observed when UART4 is used for low level debugging.
Hence, Enable DEBUG_OMAP4UART4_FLAGS for UART4 hwmod.
Signed-off-by: J.D. Schroeder <jay.schroeder@garmin.com>
Signed-off-by: Praneeth Bajjuri <praneeth@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
ELM address information is provided by device tree. No longer need
to include this information within hwmod.
This patch has only been boot tested.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Timer 12 on DRA7 SoCs is reserved for secure usage on high-secure (HS)
devices. The timer cannot be used by the kernel on HS devices, but is
available on regular general purpose (GP) devices. This is similar to the
behavior on OMAP3 devices, so extend the logic used in commit ad24bde8f1
("ARM: OMAP3: Dynamically disable secure timer nodes for secure devices")
to remove the secure timer on DRA7xx SoCs at run-time based on the SoC
device type.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Errata i810 states that DPLL controller can get stuck while transitioning
to a power saving state, while its M/N ratio is being re-programmed.
As a workaround, before re-programming the M/N ratio, SW has to ensure
the DPLL cannot start an idle state transition. SW can disable DPLL
idling by setting the DPLL AUTO_DPLL_MODE=0 or keeping a clock request
active by setting a dependent clock domain in SW_WKUP.
This errata impacts OMAP5 and DRA7 chips, so enable the errata for these.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
OMAP4 has been DT-boot only for some time, and the legacy-mode
device creation logic for IOMMU devices has also been cleaned up,
so the dev_attr and address data is no longer required. So, remove
these attribute data and hwmod addr space for the IPU & DSP IOMMU
devices.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The legacy-mode device creation logic for IOMMU devices has
been cleaned up, so the device attribute data, irq information
and address data are no longer required. Remove all of these
data for the ISP & IVA IOMMU devices.
Signed-off-by: Suman Anna <s-anna@ti.com>
[tony@atomide.com: updated to apply for the include]
Signed-off-by: Tony Lindgren <tony@atomide.com>
The legacy-style IOMMU device creation is maintained currently only
for OMAP3 SoC, as all other SoCs are DT-boot only, and also to ensure
functionality of the OMAP3 ISP driver, the only in-kernel client user
on OMAP3 that supported both modes.
Commit 78c66fbcec ("[media] v4l: omap3isp: Drop platform data support")
removed the legacy device support from the OMAP3 ISP driver, so the
legacy device instantiation of OMAP IOMMU devices is no longer
needed, and is cleaned up.
Signed-off-by: Suman Anna <s-anna@ti.com>
[tony@atomide.com: updated to remove also the Makefile entry]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add dm81xx hwmod data entries for dm816x spinbox support.
Cc: Brian Hutchinson <b.hutchman@gmail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
OMAP CPU hotplug uses cpu1's clocks and power domains for CPU1 wake up
from low power states (or turn on CPU1). This part of code is also
part of system suspend (disable_nonboot_cpus()).
>From other side, cpu1's clocks and power domains are used by CPUIdle. All above
functionality is mutually exclusive and, therefore, lockless clkdm/pwrdm api
can be used in omap4_boot_secondary().
This fixes below back-trace on -RT which is triggered by
pwrdm_lock/unlock():
BUG: sleeping function called from invalid context at kernel/locking/rtmutex.c:917
in_atomic(): 1, irqs_disabled(): 0, pid: 118, name: sh
9 locks held by sh/118:
#0: (sb_writers#4){.+.+.+}, at: [<c0144a6c>] vfs_write+0x13c/0x164
#1: (&of->mutex){+.+.+.}, at: [<c01b4c70>] kernfs_fop_write+0x48/0x19c
#2: (s_active#24){.+.+.+}, at: [<c01b4c78>] kernfs_fop_write+0x50/0x19c
#3: (device_hotplug_lock){+.+.+.}, at: [<c03cbff0>] lock_device_hotplug_sysfs+0xc/0x4c
#4: (&dev->mutex){......}, at: [<c03cd284>] device_online+0x14/0x88
#5: (cpu_add_remove_lock){+.+.+.}, at: [<c003af90>] cpu_up+0x50/0x1a0
#6: (cpu_hotplug.lock){++++++}, at: [<c003ae48>] cpu_hotplug_begin+0x0/0xc4
#7: (cpu_hotplug.lock#2){+.+.+.}, at: [<c003aec0>] cpu_hotplug_begin+0x78/0xc4
#8: (boot_lock){+.+...}, at: [<c002b254>] omap4_boot_secondary+0x1c/0x178
Preemption disabled at:[< (null)>] (null)
CPU: 0 PID: 118 Comm: sh Not tainted 4.1.12-rt11-01998-gb4a62c3-dirty #137
Hardware name: Generic DRA74X (Flattened Device Tree)
[<c0017574>] (unwind_backtrace) from [<c0013be8>] (show_stack+0x10/0x14)
[<c0013be8>] (show_stack) from [<c05a8670>] (dump_stack+0x80/0x94)
[<c05a8670>] (dump_stack) from [<c05ad158>] (rt_spin_lock+0x24/0x54)
[<c05ad158>] (rt_spin_lock) from [<c0030dac>] (clkdm_wakeup+0x10/0x2c)
[<c0030dac>] (clkdm_wakeup) from [<c002b2c0>] (omap4_boot_secondary+0x88/0x178)
[<c002b2c0>] (omap4_boot_secondary) from [<c0015d00>] (__cpu_up+0xc4/0x164)
[<c0015d00>] (__cpu_up) from [<c003b09c>] (cpu_up+0x15c/0x1a0)
[<c003b09c>] (cpu_up) from [<c03cd2d4>] (device_online+0x64/0x88)
[<c03cd2d4>] (device_online) from [<c03cd360>] (online_store+0x68/0x74)
[<c03cd360>] (online_store) from [<c01b4ce0>] (kernfs_fop_write+0xb8/0x19c)
[<c01b4ce0>] (kernfs_fop_write) from [<c0144124>] (__vfs_write+0x20/0xd8)
[<c0144124>] (__vfs_write) from [<c01449c0>] (vfs_write+0x90/0x164)
[<c01449c0>] (vfs_write) from [<c01451e4>] (SyS_write+0x44/0x9c)
[<c01451e4>] (SyS_write) from [<c0010240>] (ret_fast_syscall+0x0/0x54)
CPU1: smp_ops.cpu_die() returned, trying to resuscitate
Cc: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add missing HWMOD_NO_IDLEST hwmod flag for entries not
having omap4 clkctrl values.
The emac0 hwmod flag fixes the davinci_emac driver probe
since the return of pm_resume() call is now checked.
This solves the following boot errors :
[ 0.121429] omap_hwmod: l4_ls: _wait_target_ready failed: -16
[ 0.121441] omap_hwmod: l4_ls: cannot be enabled for reset (3)
[ 0.124342] omap_hwmod: l4_hs: _wait_target_ready failed: -16
[ 0.124352] omap_hwmod: l4_hs: cannot be enabled for reset (3)
[ 1.967228] omap_hwmod: emac0: _wait_target_ready failed: -16
Cc: Brian Hutchinson <b.hutchman@gmail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Let's not mix platform_data headers with the core headers. Instead, let's
create a subdir at linux/platform_data and move the headers to that
common place, adding it to MAINTAINERS.
The headers were moved with:
mkdir include/linux/platform_data/media/; git mv include/media/gpio-ir-recv.h include/media/ir-rx51.h include/media/mmp-camera.h include/media/omap1_camera.h include/media/omap4iss.h include/media/s5p_hdmi.h include/media/si4713.h include/media/sii9234.h include/media/smiapp.h include/media/soc_camera.h include/media/soc_camera_platform.h include/media/timb_radio.h include/media/timb_video.h include/linux/platform_data/media/
And the references fixed with this script:
MAIN_DIR="linux/platform_data/"
PREV_DIR="media/"
DIRS="media/"
echo "Checking affected files" >&2
for i in $DIRS; do
for j in $(find include/$MAIN_DIR/$i -type f -name '*.h'); do
n=`basename $j`
git grep -l $n
done
done|sort|uniq >files && (
echo "Handling files..." >&2;
echo "for i in \$(cat files|grep -v Documentation); do cat \$i | \\";
(
cd include/$MAIN_DIR;
for j in $DIRS; do
for i in $(ls $j); do
echo "perl -ne 's,(include [\\\"\\<])$PREV_DIR($i)([\\\"\\>]),\1$MAIN_DIR$j\2\3,; print \$_' |\\";
done;
done;
echo "cat > a && mv a \$i; done";
);
echo "Handling documentation..." >&2;
echo "for i in MAINTAINERS \$(cat files); do cat \$i | \\";
(
cd include/$MAIN_DIR;
for j in $DIRS; do
for i in $(ls $j); do
echo " perl -ne 's,include/$PREV_DIR($i)\b,include/$MAIN_DIR$j\1,; print \$_' |\\";
done;
done;
echo "cat > a && mv a \$i; done"
);
) >script && . ./script
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
This is not needed anymore. Handling a potentially pending imprecise external
abort left behind by the bootloader is now done in a slightly safer way inside
the common ARM startup code.
With the recent changes to abort handling, this issue got fixed by 57df538085
("ARM: OMAP2+: Fix imprecise external abort caused by bogus SRAM init").
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
[tony@atomide.com: updated comments to describe what fixed the issue]
Signed-off-by: Tony Lindgren <tony@atomide.com>
McASP3 is used by default on DRA7x based boards for audio.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Some module needs more than one functional clock in order to be accessible,
like the McASPs found in DRA7xx family.
This flag will indicate that the opt_clks need to be handled at the same
time as the main_clk for the given hwmod, ensuring that all needed clocks
are enabled before we try to access the module's address space.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Again we have a sizable (but not huge) cleanup branch with a net delta of about
-3k lines.
Main contents here is:
- A bunch of development/cleanup of a few PXA boards
- Removal of bockw platforms on shmobile, since the platform has now gone
completely multiplatform. Whee!
- move of the 32kHz timer on OMAP to a proper timesource
- Misc cleanup of older OMAP material (incl removal of one board file)
- Switch over to new common PWM lookup support for several platforms
There's also a handful of other cleanups across the tree, but the above are
the major pieces.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=uI7R
-----END PGP SIGNATURE-----
Merge tag 'armsoc-cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC cleanups from Olof Johansson:
"Again we have a sizable (but not huge) cleanup branch with a net delta
of about -3k lines.
Main contents here is:
- A bunch of development/cleanup of a few PXA boards
- Removal of bockw platforms on shmobile, since the platform has now
gone completely multiplatform. Whee!
- move of the 32kHz timer on OMAP to a proper timesource
- Misc cleanup of older OMAP material (incl removal of one board
file)
- Switch over to new common PWM lookup support for several platforms
There's also a handful of other cleanups across the tree, but the
above are the major pieces"
* tag 'armsoc-cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (103 commits)
ARM: OMAP3: hwmod data: Remove legacy mailbox data and addrs
ARM: DRA7: hwmod data: Remove spinlock hwmod addrs
ARM: OMAP4: hwmod data: Remove spinlock hwmod addrs
ARM: DRA7/AM335x/AM437x: hwmod: Remove gpmc address space from hwmod data
ARM: Remove __ref on hotplug cpu die path
ARM: Remove open-coded version of IRQCHIP_DECLARE
arm: omap2: board-generic: use omap4_local_timer_init for AM437x
ARM: DRA7/AM335x/AM437x: hwmod: Remove elm address space from hwmod data
ARM: OMAP: Remove duplicated operand in OR operation
clocksource: ti-32k: make it depend on GENERIC_CLOCKSOURCE
ARM: pxa: remove incorrect __init annotation on pxa27x_set_pwrmode
ARM: pxa: raumfeld: make some variables static
ARM: OMAP: Change all cpu_is_* occurences to soc_is_* for id.c
ARM: OMAP2+: Rename cpu_is macros to soc_is
arm: omap2: timer: limit hwmod usage to non-DT boots
arm: omap2+: select 32k clocksource driver
clocksource: add TI 32.768 Hz counter driver
arm: omap2: timer: rename omap_sync32k_timer_init()
arm: omap2: timer: always call clocksource_of_init() when DT
arm: omap2: timer: move realtime_counter_init() around
...
This time we have a very typical update which is mostly fixes and updates to
drivers and no new drivers.
- Biggest change is coming from Peter for edma cleanup which even caused
some last minute regression, things seem settled now
- idma64 and dw updates
- iotdma updates
- module autoload fixes for various drivers
- scatter gather support for hdmac
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=tIzO
-----END PGP SIGNATURE-----
Merge tag 'dmaengine-4.4-rc1' of git://git.infradead.org/users/vkoul/slave-dma
Pull dmaengine updates from Vinod Koul:
"This time we have a very typical update which is mostly fixes and
updates to drivers and no new drivers.
- the biggest change is coming from Peter for edma cleanup which even
caused some last minute regression, things seem settled now
- idma64 and dw updates
- iotdma updates
- module autoload fixes for various drivers
- scatter gather support for hdmac"
* tag 'dmaengine-4.4-rc1' of git://git.infradead.org/users/vkoul/slave-dma: (77 commits)
dmaengine: edma: Add dummy driver skeleton for edma3-tptc
Revert "ARM: DTS: am33xx: Use the new DT bindings for the eDMA3"
Revert "ARM: DTS: am437x: Use the new DT bindings for the eDMA3"
dmaengine: dw: some Intel devices has no memcpy support
dmaengine: dw: platform: provide platform data for Intel
dmaengine: dw: don't override platform data with autocfg
dmaengine: hdmac: Add scatter-gathered memset support
dmaengine: hdmac: factorise memset descriptor allocation
dmaengine: virt-dma: Fix kernel-doc annotations
ARM: DTS: am437x: Use the new DT bindings for the eDMA3
ARM: DTS: am33xx: Use the new DT bindings for the eDMA3
dmaengine: edma: New device tree binding
dmaengine: Kconfig: edma: Select TI_DMA_CROSSBAR in case of ARCH_OMAP
dmaengine: ti-dma-crossbar: Add support for crossbar on AM33xx/AM43xx
dmaengine: edma: Merge the of parsing functions
dmaengine: edma: Do not allocate memory for edma_rsv_info in case of DT boot
dmaengine: edma: Refactor the dma device and channel struct initialization
dmaengine: edma: Get qDMA channel information from HW also
dmaengine: edma: Merge map_dmach_to_queue into assign_channel_eventq
dmaengine: edma: Correct PaRAM access function names (_parm_ to _param_)
...
- ACPICA update to upstream revision 20150930 (Bob Moore, Lv Zheng).
The most significant change is to allow the AML debugger to be
built into the kernel. On top of that there is an update related
to the NFIT table (the ACPI persistent memory interface)
and a few fixes and cleanups.
- ACPI CPPC2 (Collaborative Processor Performance Control v2)
support along with a cpufreq frontend (Ashwin Chaugule).
This can only be enabled on ARM64 at this point.
- New ACPI infrastructure for the early probing of IRQ chips and
clock sources (Marc Zyngier).
- Support for a new hierarchical properties extension of the ACPI
_DSD (Device Specific Data) device configuration object allowing
the kernel to handle hierarchical properties (provided by the
platform firmware this way) automatically and make them available
to device drivers via the generic device properties interface
(Rafael Wysocki).
- Generic device properties API extension to obtain an index of
certain string value in an array of strings, along the lines of
of_property_match_string(), but working for all of the supported
firmware node types, and support for the "dma-names" device
property based on it (Mika Westerberg).
- ACPI core fix to parse the MADT (Multiple APIC Description Table)
entries in the order expected by platform firmware (and mandated
by the specification) to avoid confusion on systems with more than
255 logical CPUs (Lukasz Anaczkowski).
- Consolidation of the ACPI-based handling of PCI host bridges
on x86 and ia64 (Jiang Liu).
- ACPI core fixes to ensure that the correct IRQ number is used to
represent the SCI (System Control Interrupt) in the cases when
it has been re-mapped (Chen Yu).
- New ACPI backlight quirk for Lenovo IdeaPad S405 (Hans de Goede).
- ACPI EC driver fixes (Lv Zheng).
- Assorted ACPI fixes and cleanups (Dan Carpenter, Insu Yun, Jiri
Kosina, Rami Rosen, Rasmus Villemoes).
- New mechanism in the PM core allowing drivers to check if the
platform firmware is going to be involved in the upcoming system
suspend or if it has been involved in the suspend the system is
resuming from at the moment (Rafael Wysocki).
This should allow drivers to optimize their suspend/resume
handling in some cases and the changes include a couple of users
of it (the i8042 input driver, PCI PM).
- PCI PM fix to prevent runtime-suspended devices with PME enabled
from being resumed during system suspend even if they aren't
configured to wake up the system from sleep (Rafael Wysocki).
- New mechanism to report the number of a wakeup IRQ that woke up
the system from sleep last time (Alexandra Yates).
- Removal of unused interfaces from the generic power domains
framework and fixes related to latency measurements in that
code (Ulf Hansson, Daniel Lezcano).
- cpufreq core sysfs interface rework to make it handle CPUs that
share performance scaling settings (represented by a common
cpufreq policy object) more symmetrically (Viresh Kumar).
This should help to simplify the CPU offline/online handling among
other things.
- cpufreq core fixes and cleanups (Viresh Kumar).
- intel_pstate fixes related to the Turbo Activation Ratio (TAR)
mechanism on client platforms which causes the turbo P-states
range to vary depending on platform firmware settings (Srinivas
Pandruvada).
- intel_pstate sysfs interface fix (Prarit Bhargava).
- Assorted cpufreq driver (imx, tegra20, powernv, integrator) fixes
and cleanups (Bai Ping, Bartlomiej Zolnierkiewicz, Shilpasri G
Bhat, Luis de Bethencourt).
- cpuidle mvebu driver cleanups (Russell King).
- OPP (Operating Performance Points) framework code reorganization
to make it more maintainable (Viresh Kumar).
- Intel Broxton support for the RAPL (Running Average Power Limits)
power capping driver (Amy Wiles).
- Assorted power management code fixes and cleanups (Dan Carpenter,
Geert Uytterhoeven, Geliang Tang, Luis de Bethencourt, Rasmus
Villemoes).
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=1gaH
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-4.4-rc1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management and ACPI updates from Rafael Wysocki:
"Quite a new features are included this time.
First off, the Collaborative Processor Performance Control interface
(version 2) defined by ACPI will now be supported on ARM64 along with
a cpufreq frontend for CPU performance scaling.
Second, ACPI gets a new infrastructure for the early probing of IRQ
chips and clock sources (along the lines of the existing similar
mechanism for DT).
Next, the ACPI core and the generic device properties API will now
support a recently introduced hierarchical properties extension of the
_DSD (Device Specific Data) ACPI device configuration object. If the
ACPI platform firmware uses that extension to organize device
properties in a hierarchical way, the kernel will automatically handle
it and make those properties available to device drivers via the
generic device properties API.
It also will be possible to build the ACPICA's AML interpreter
debugger into the kernel now and use that to diagnose AML-related
problems more efficiently. In the future, this should make it
possible to single-step AML execution and do similar things.
Interesting stuff, although somewhat experimental at this point.
Finally, the PM core gets a new mechanism that can be used by device
drivers to distinguish between suspend-to-RAM (based on platform
firmware support) and suspend-to-idle (or other variants of system
suspend the platform firmware is not involved in) and possibly
optimize their device suspend/resume handling accordingly.
In addition to that, some existing features are re-organized quite
substantially.
First, the ACPI-based handling of PCI host bridges on x86 and ia64 is
unified and the common code goes into the ACPI core (so as to reduce
code duplication and eliminate non-essential differences between the
two architectures in that area).
Second, the Operating Performance Points (OPP) framework is
reorganized to make the code easier to find and follow.
Next, the cpufreq core's sysfs interface is reorganized to get rid of
the "primary CPU" concept for configurations in which the same
performance scaling settings are shared between multiple CPUs.
Finally, some interfaces that aren't necessary any more are dropped
from the generic power domains framework.
On top of the above we have some minor extensions, cleanups and bug
fixes in multiple places, as usual.
Specifics:
- ACPICA update to upstream revision 20150930 (Bob Moore, Lv Zheng).
The most significant change is to allow the AML debugger to be
built into the kernel. On top of that there is an update related
to the NFIT table (the ACPI persistent memory interface) and a few
fixes and cleanups.
- ACPI CPPC2 (Collaborative Processor Performance Control v2) support
along with a cpufreq frontend (Ashwin Chaugule).
This can only be enabled on ARM64 at this point.
- New ACPI infrastructure for the early probing of IRQ chips and
clock sources (Marc Zyngier).
- Support for a new hierarchical properties extension of the ACPI
_DSD (Device Specific Data) device configuration object allowing
the kernel to handle hierarchical properties (provided by the
platform firmware this way) automatically and make them available
to device drivers via the generic device properties interface
(Rafael Wysocki).
- Generic device properties API extension to obtain an index of
certain string value in an array of strings, along the lines of
of_property_match_string(), but working for all of the supported
firmware node types, and support for the "dma-names" device
property based on it (Mika Westerberg).
- ACPI core fix to parse the MADT (Multiple APIC Description Table)
entries in the order expected by platform firmware (and mandated by
the specification) to avoid confusion on systems with more than 255
logical CPUs (Lukasz Anaczkowski).
- Consolidation of the ACPI-based handling of PCI host bridges on x86
and ia64 (Jiang Liu).
- ACPI core fixes to ensure that the correct IRQ number is used to
represent the SCI (System Control Interrupt) in the cases when it
has been re-mapped (Chen Yu).
- New ACPI backlight quirk for Lenovo IdeaPad S405 (Hans de Goede).
- ACPI EC driver fixes (Lv Zheng).
- Assorted ACPI fixes and cleanups (Dan Carpenter, Insu Yun, Jiri
Kosina, Rami Rosen, Rasmus Villemoes).
- New mechanism in the PM core allowing drivers to check if the
platform firmware is going to be involved in the upcoming system
suspend or if it has been involved in the suspend the system is
resuming from at the moment (Rafael Wysocki).
This should allow drivers to optimize their suspend/resume handling
in some cases and the changes include a couple of users of it (the
i8042 input driver, PCI PM).
- PCI PM fix to prevent runtime-suspended devices with PME enabled
from being resumed during system suspend even if they aren't
configured to wake up the system from sleep (Rafael Wysocki).
- New mechanism to report the number of a wakeup IRQ that woke up the
system from sleep last time (Alexandra Yates).
- Removal of unused interfaces from the generic power domains
framework and fixes related to latency measurements in that code
(Ulf Hansson, Daniel Lezcano).
- cpufreq core sysfs interface rework to make it handle CPUs that
share performance scaling settings (represented by a common cpufreq
policy object) more symmetrically (Viresh Kumar).
This should help to simplify the CPU offline/online handling among
other things.
- cpufreq core fixes and cleanups (Viresh Kumar).
- intel_pstate fixes related to the Turbo Activation Ratio (TAR)
mechanism on client platforms which causes the turbo P-states range
to vary depending on platform firmware settings (Srinivas
Pandruvada).
- intel_pstate sysfs interface fix (Prarit Bhargava).
- Assorted cpufreq driver (imx, tegra20, powernv, integrator) fixes
and cleanups (Bai Ping, Bartlomiej Zolnierkiewicz, Shilpasri G
Bhat, Luis de Bethencourt).
- cpuidle mvebu driver cleanups (Russell King).
- OPP (Operating Performance Points) framework code reorganization to
make it more maintainable (Viresh Kumar).
- Intel Broxton support for the RAPL (Running Average Power Limits)
power capping driver (Amy Wiles).
- Assorted power management code fixes and cleanups (Dan Carpenter,
Geert Uytterhoeven, Geliang Tang, Luis de Bethencourt, Rasmus
Villemoes)"
* tag 'pm+acpi-4.4-rc1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (108 commits)
cpufreq: postfix policy directory with the first CPU in related_cpus
cpufreq: create cpu/cpufreq/policyX directories
cpufreq: remove cpufreq_sysfs_{create|remove}_file()
cpufreq: create cpu/cpufreq at boot time
cpufreq: Use cpumask_copy instead of cpumask_or to copy a mask
cpufreq: ondemand: Drop unnecessary locks from update_sampling_rate()
PM / Domains: Merge measurements for PM QoS device latencies
PM / Domains: Don't measure ->start|stop() latency in system PM callbacks
PM / clk: Fix broken build due to non-matching code and header #ifdefs
ACPI / Documentation: add copy_dsdt to ACPI format options
ACPI / sysfs: correctly check failing memory allocation
ACPI / video: Add a quirk to force native backlight on Lenovo IdeaPad S405
ACPI / CPPC: Fix potential memory leak
ACPI / CPPC: signedness bug in register_pcc_channel()
ACPI / PAD: power_saving_thread() is not freezable
ACPI / PM: Fix incorrect wakeup IRQ setting during suspend-to-idle
ACPI: Using correct irq when waiting for events
ACPI: Use correct IRQ when uninstalling ACPI interrupt handler
cpuidle: mvebu: disable the bind/unbind attributes and use builtin_platform_driver
cpuidle: mvebu: clean up multiple platform drivers
...
Pull irq updates from Thomas Gleixner:
"The irq departement delivers:
- Rework the irqdomain core infrastructure to accomodate ACPI based
systems. This is required to support ARM64 without creating
artificial device tree nodes.
- Sanitize the ACPI based ARM GIC initialization by making use of the
new firmware independent irqdomain core
- Further improvements to the generic MSI management
- Generalize the irq migration on CPU hotplug
- Improvements to the threaded interrupt infrastructure
- Allow the migration of "chained" low level interrupt handlers
- Allow optional force masking of interrupts in disable_irq[_nosysnc]
- Support for two new interrupt chips - Sigh!
- A larger set of errata fixes for ARM gicv3
- The usual pile of fixes, updates, improvements and cleanups all
over the place"
* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (71 commits)
Document that IRQ_NONE should be returned when IRQ not actually handled
PCI/MSI: Allow the MSI domain to be device-specific
PCI: Add per-device MSI domain hook
of/irq: Use the msi-map property to provide device-specific MSI domain
of/irq: Split of_msi_map_rid to reuse msi-map lookup
irqchip/gic-v3-its: Parse new version of msi-parent property
PCI/MSI: Use of_msi_get_domain instead of open-coded "msi-parent" parsing
of/irq: Use of_msi_get_domain instead of open-coded "msi-parent" parsing
of/irq: Add support code for multi-parent version of "msi-parent"
irqchip/gic-v3-its: Add handling of PCI requester id.
PCI/MSI: Add helper function pci_msi_domain_get_msi_rid().
of/irq: Add new function of_msi_map_rid()
Docs: dt: Add PCI MSI map bindings
irqchip/gic-v2m: Add support for multiple MSI frames
irqchip/gic-v3: Fix translation of LPIs after conversion to irq_fwspec
irqchip/mxs: Add Alphascale ASM9260 support
irqchip/mxs: Prepare driver for hardware with different offsets
irqchip/mxs: Panic if ioremap or domain creation fails
irqdomain: Documentation updates
irqdomain/msi: Use fwnode instead of of_node
...
bit of time sorting out regressions for v4.3 and are very late with
these, I've kept the changes down to minimum:
- A series of timer changes from Felipe Balbi to get us closer to
moving the remaining timer code into drivers
- A series of hwmod clean-up changes queued by Paul Walmsley
- SoC detection clean-up to use soc_is instead of cpu_is as CPU is
within the SoC and is confusing naming. The rest we can now change
along with the other clean-up
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=gNfn
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.4/soc-clean-up' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/cleanup
Minimal omap SoC changes for v4.4 merge window. As we've spent quite a
bit of time sorting out regressions for v4.3 and are very late with
these, I've kept the changes down to minimum:
- A series of timer changes from Felipe Balbi to get us closer to
moving the remaining timer code into drivers
- A series of hwmod clean-up changes queued by Paul Walmsley
- SoC detection clean-up to use soc_is instead of cpu_is as CPU is
within the SoC and is confusing naming. The rest we can now change
along with the other clean-up
* tag 'omap-for-v4.4/soc-clean-up' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (21 commits)
ARM: OMAP3: hwmod data: Remove legacy mailbox data and addrs
ARM: DRA7: hwmod data: Remove spinlock hwmod addrs
ARM: OMAP4: hwmod data: Remove spinlock hwmod addrs
ARM: DRA7/AM335x/AM437x: hwmod: Remove gpmc address space from hwmod data
arm: omap2: board-generic: use omap4_local_timer_init for AM437x
ARM: DRA7/AM335x/AM437x: hwmod: Remove elm address space from hwmod data
ARM: OMAP: Remove duplicated operand in OR operation
clocksource: ti-32k: make it depend on GENERIC_CLOCKSOURCE
ARM: OMAP: Change all cpu_is_* occurences to soc_is_* for id.c
ARM: OMAP2+: Rename cpu_is macros to soc_is
arm: omap2: timer: limit hwmod usage to non-DT boots
arm: omap2+: select 32k clocksource driver
clocksource: add TI 32.768 Hz counter driver
arm: omap2: timer: rename omap_sync32k_timer_init()
arm: omap2: timer: always call clocksource_of_init() when DT
arm: omap2: timer: move realtime_counter_init() around
arm: omap2: timer: provide generic sync32k_timer_init function
arm: omap2: timer: remove __omap_gptimer_init()
arm: omap2: timer: add a gptimer argument to sync32k_timer_init()
arm: omap2: timer: get rid of obfuscating macros
...
Signed-off-by: Olof Johansson <olof@lixom.net>
Remove some superfluous data from the OMAP2+ hwmod data files. Mostly
this is a result of data being moved to DT files. Nothing too
controversial, here.
Basic build, boot, and PM test results are available here:
http://www.pwsan.com/omap/testlogs/hwmod-cleanup-a-for-v4.4/20151023130140/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=AVI9
-----END PGP SIGNATURE-----
Merge tag 'for-v4.4/omap-hwmod-cleanup-a' of git://git.kernel.org/pub/scm/linux/kernel/git/pjw/omap-pending into omap-for-v4.4/soc
ARM: OMAP2+: hwmod cleanup for v4.4
Remove some superfluous data from the OMAP2+ hwmod data files. Mostly
this is a result of data being moved to DT files. Nothing too
controversial, here.
Basic build, boot, and PM test results are available here:
http://www.pwsan.com/omap/testlogs/hwmod-cleanup-a-for-v4.4/20151023130140/
Remove the mailbox attribute data, irq info and hwmod addr space
data that are used for creating the legacy-style mailbox devices,
there is no need for these as the support for legacy-mode for this
IP is being dropped.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
The legacy-style device creation logic for hwspinlock
has been removed after the DT-support was added to the
driver. The hwmod addr space for spinlock is therefore
no longer needed, so remove it.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
The legacy-style device creation logic for hwspinlock
has been removed after the DT-support was added to the
driver. The hwmod addr space for spinlock is therefore
no longer needed, so remove it.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
GPMC address information is provided by device tree. No longer need
to include this information within hwmod.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Acked-by: Roger Quadros <rogerq@ti.com>
[paul@pwsan.com: fixed chip names in subject line]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Now that __cpuinit has been removed, the __ref markings on these
functions are useless. Remove them. This also reduces the size of
the multi_v7_defconfig image:
$ size before after
text data bss dec hex filename
12683578 1470996 348904 14503478 dd4e36 before
12683274 1470996 348904 14503174 dd4d06 after
presumably because now we don't have to jump to code in the
.ref.text section and/or the noinline marking is removed.
Cc: Shiraz Hashim <shiraz.linux.kernel@gmail.com>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: <linux-omap@vger.kernel.org>
Cc: <linux-arm-msm@vger.kernel.org>
Cc: <spear-devel@list.st.com>
Cc: <linux-tegra@vger.kernel.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Barry Song <baohua@kernel.org>
Acked-by: Andy Gross <agross@codeaurora.org>
Acked-by: Viresh Kumar <vireshk@kernel.org>
Acked-by: Thierry Reding <thierry.reding@gmail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Sudeep Holla <sudeep.holla@arm.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Now that the IRQCHIP_DECLARE macro has been moved to linux/irqchip.h,
it becomes possible to cleanup the open-coded versions of the same
macro that have been added to some private irqchips implementations.
Cc: Sascha Hauer <kernel@pengutronix.de>
Acked-by: Kukjin Kim <kgene@kernel.org>
Acked-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
AM437x-based boards, can use omap4_local_timer_init()
just fine. Let's use that instead.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
ELM address information is provided by device tree. No longer need
to include this information within hwmod.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Acked-by: Roger Quadros <rogerq@ti.com>
[paul@pwsan.com: fixed chip names in subject line; dropped the OMAP4 section
since the OMAP4 SoC DTS file doesn't have the ELM address space documented
yet]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Commit b483a4a5a7 ("ARM: OMAP4+: hwmod data: Don't prevent RESET of
USB Host module") added the SYSC_HAS_RESET_STATUS flag to both OMAP4
and OMAP5 USB host module hwmon sysconfig but that flag was already
set for OMAP5. So now the flag appears twice in the expression.
make coccicheck complains with the following message:
omap_hwmod_54xx_data.c:1846:37-58: duplicated argument to & or |
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Some omaps are producing imprecise external aborts because we are
wrongly trying to init SRAM for device tree based booting. Only
omap3 is still using the legacy SRAM code, so we need to make it
omap3 specific. Otherwise we can get errors like this on at least
dm814x:
Unhandled fault: imprecise external abort (0xc06) at 0xc08b156c
...
(omap_rev) from [<c08b12e0>] (omap_sram_init+0xf8/0x3e0)
(omap_sram_init) from [<c08aca0c>] (omap_sdrc_init+0x10/0xb0)
(omap_sdrc_init) from [<c08b581c>] (pdata_quirks_init+0x18/0x44)
(pdata_quirks_init) from [<c08b5478>] (omap_generic_init+0x10/0x1c)
(omap_generic_init) from [<c08a57e0>] (customize_machine+0x1c/0x40)
(customize_machine) from [<c00098a4>] (do_one_initcall+0x80/0x1dc)
(do_one_initcall) from [<c08a2ec4>] (kernel_init_freeable+0x218/0x2e8)
(kernel_init_freeable) from [<c063a554>] (kernel_init+0x8/0xec)
(kernel_init) from [<c000f890>] (ret_from_fork+0x14/0x24)
Let's fix the issue by making sure omap_sdrc_init only gets called for
omap3. To do that, we need to have compatible "ti,omap3" in the dts
files. And let's also use "ti,omap3630" instead of "ti,omap36xx" like
we're supposed to.
Signed-off-by: Tony Lindgren <tony@atomide.com>
On boards with more than 2GB of RAM booting goes wrong with things not
working and we're getting lots of l3 warnings:
WARNING: CPU: 0 PID: 1 at drivers/bus/omap_l3_noc.c:147
l3_interrupt_handler+0x260/0x384()
44000000.ocp:L3 Custom Error: MASTER MMC6 TARGET DMM1 (Idle):
Data Access in User mode during Functional access
...
[<c044e158>] (scsi_add_host_with_dma) from [<c04705c8>]
(ata_scsi_add_hosts+0x5c/0x18c)
[<c04705c8>] (ata_scsi_add_hosts) from [<c046b13c>]
(ata_host_register+0x150/0x2cc)
[<c046b13c>] (ata_host_register) from [<c046b38c>]
(ata_host_activate+0xd4/0x124)
[<c046b38c>] (ata_host_activate) from [<c047f42c>]
(ahci_host_activate+0x5c/0x194)
[<c047f42c>] (ahci_host_activate) from [<c0480854>]
(ahci_platform_init_host+0x1f0/0x3f0)
[<c0480854>] (ahci_platform_init_host) from [<c047c9dc>]
(ahci_probe+0x70/0x98)
[<c047c9dc>] (ahci_probe) from [<c04220cc>]
(platform_drv_probe+0x54/0xb4)
Let's fix the issue by enabling ZONE_DMA for LPAE. Note that we need to
limit dma_zone_size to 2GB as the rest of the RAM is beyond the 4GB limit.
Let's also fix things for dra7 as done in similar patches in the TI tree
by Lokesh Vutla <lokeshvutla@ti.com>.
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Currently apart from dra7, omap5 and amx3 all the other SoCs
are identified using cpu_is_* functions which is not right since
they are all SoCs(System on Chips). Hence changing the SoC
identification code to use soc_is instead of cpu_is and keeping
defines for cpu_is where needed. This allows us to replace the
rest of cpu_is usage along with other fixes as needed.
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Keerthy <j-keerthy@ti.com>
[tony@atomide.com: reworked the soc.h changes to minimum]
Signed-off-by: Tony Lindgren <tony@atomide.com>
The naming for the cpu_is macros is confusing as the CPU is separate
and within the SoC. Let's rename all the macros to soc_is, and let's
define cpu_is also for the ones still in use. Then we can just remove
the cpu_is macros once the users are fixed up.
To keep the chances of breaking anything, the changes were
generated with the following regular expressions:
s/cpu_is/soc_is/g
s/CPU/SoC/g
Then the list of existing cpu_is users was generated with:
$ $ grep -o -e 'cpu_is_.\+()' arch/arm/mach-omap2/*.[chS] | \
cut -d: -f2 | sort | uniq
And added to the end of the soc.h.
I decided to rework the earlier patches by Keerthy <j-keerthy@ti.com>
to keep changes down to minimum to avoid potential errors and stick
to just search and replace.
Signed-off-by: Tony Lindgren <tony@atomide.com>
now that we have a working 32k clocksource driver,
we can limit HWMOD usage to non-DT boots and rely
on clocksource_of_init() every time we boot
with DT.
While at that, also make sure that we don't disable
the 32-counter device so it gets probed by its driver.
Signed-off-by: Felipe Balbi <balbi@ti.com>
this function is not only about the 32k sync
timer, it's OMAP's generic init_time implementation.
Let's rename it to make that detail easier to
notice.
Signed-off-by: Felipe Balbi <balbi@ti.com>
If booting with DT, let's make sure to always
call clocksource_of_init() as this will make
it easier to move timer code to drivers/clocksource
in the future.
Signed-off-by: Felipe Balbi <balbi@ti.com>
instead of constantly defining a small wrapper
around __omap_sync32k_timer_init(), let's define
a generic one which can be used by all OMAPs.
Signed-off-by: Felipe Balbi <balbi@ti.com>
__omap_sync32k_timer_init(), now takes the clock
source as a parameter. This means we no longer need
__omap_gptimer_init().
Note that __omap_sync32k_timer_init() will be
renamed in a follow-up patch as it's not longer 32k
source specific.
Signed-off-by: Felipe Balbi <balbi@ti.com>
as it turns out, __omap_gptimer_init() and
__omap_sync32k_timer_init() are essentially
the same thing, but __omap_gptimer_init() wants
to always use gptimer.
Instead of forcing all those devices to pass
a use_gptimer cmdline argument, we add a new
function argument to __omap_sync32k_timer_init()
in preparation to deleting __omap_gptimer_init().
On a follow-up patch, we will remove uses of
__omap_gptimer_init() and replace them with
__omap_sync32k_timer_init() and pass the last
argument as true.
Signed-off-by: Felipe Balbi <balbi@ti.com>
those macros just make it a lot more difficult
to grep around and actually find similarities.
In this patch, we will simply remove them and
replace with actual functions and later commits
will come to further clean this up.
Signed-off-by: Felipe Balbi <balbi@ti.com>
omap4_local_timer_init() can be used by other
platforms as is. At least AM437x wants to use
it. Instead of making omap4-only and providing
a stub for builds without OMAP4, we can just
make sure that function is always available
for all SoCs that need it.
Reported-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Remove the OMAP3 core DPLL re-program code, and the associated SRAM
code that does the low-level programming of the DPLL divider, idling
of the SDRAM etc.
This code was never fully implemented in the kernel; things missing
were driver side handling of core clock changes (they need to account
for their functional clock rate being changed on-the-fly), and the whole
framework required for handling this. Thus, there is not much point
to keep carrying the low-level support code either.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Move the code out from arch/arm/common and merge it inside of the dmaengine
driver.
This change is done with as minimal (if eny) functional change to the code
as possible to avoid introducing regression.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Since we now have a generic data structure to express an
interrupt specifier, convert all hierarchical irqchips that
are OF based to use a fwnode_handle as part of their alloc
and xlate (which becomes translate) callbacks.
As most of these drivers have dependencies (they exchange IRQ
specifiers), change them all in a single, massive patch...
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Reviewed-and-tested-by: Hanjun Guo <hanjun.guo@linaro.org>
Tested-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: <linux-arm-kernel@lists.infradead.org>
Cc: Tomasz Nowicki <tomasz.nowicki@linaro.org>
Cc: Suravee Suthikulpanit <Suravee.Suthikulpanit@amd.com>
Cc: Graeme Gregory <graeme@xora.org.uk>
Cc: Jake Oshins <jakeo@microsoft.com>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Link: http://lkml.kernel.org/r/1444737105-31573-6-git-send-email-marc.zyngier@arm.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The struct irq_domain contains a "struct device_node *" field
(of_node) that is almost the only link between the irqdomain
and the device tree infrastructure.
In order to prepare for the removal of that field, convert all
users to use irq_domain_get_of_node() instead.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Reviewed-and-tested-by: Hanjun Guo <hanjun.guo@linaro.org>
Tested-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: <linux-arm-kernel@lists.infradead.org>
Cc: Tomasz Nowicki <tomasz.nowicki@linaro.org>
Cc: Suravee Suthikulpanit <Suravee.Suthikulpanit@amd.com>
Cc: Graeme Gregory <graeme@xora.org.uk>
Cc: Jake Oshins <jakeo@microsoft.com>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Link: http://lkml.kernel.org/r/1444737105-31573-2-git-send-email-marc.zyngier@arm.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The cpuidle tracepoints are called within a rcu_idle_exit() section, and
must be denoted with the _rcuidle() version of the tracepoint.
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Remove the unneded semicolons since they are clearly a typo error.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The PRM_POLCTRL_TWL_MASK and PRM_POLCTRL_TWL_MASK
macros are not used so they can be deleted.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The OMAP3 ISP is now fully supported in DT, remove its instantiation
from C code.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Seeing the 'of' characters in a symbol that is being called from
ACPI seems to freak out people. So let's do a bit of pointless
renaming so that these folks do feel at home.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Reviewed-by: Hanjun Guo <hanjun.guo@linaro.org>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Hanjun Guo <hanjun.guo@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Our first real batch of fixes this release cycle. There's a collection of
them here:
- A fixup for a build breakage that hits on arm64 allmodconfig in QCOM SCM
firmware drivers
- MMC fixes for OMAP that had quite a bit of breakage this merge window.
- Misc build/warning fixes on PXA and OMAP
- A couple of minor fixes for Beagleboard X15 which is now starting to see
a few more users in the wild
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=ThcO
-----END PGP SIGNATURE-----
Merge tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"Our first real batch of fixes this release cycle. Nothing really
concerning, and diffstat is a bit inflated due to some DT contents
moving around on STi platforms.
There's a collection of them here:
- A fixup for a build breakage that hits on arm64 allmodconfig in
QCOM SCM firmware drivers
- MMC fixes for OMAP that had quite a bit of breakage this merge
window.
- Misc build/warning fixes on PXA and OMAP
- A couple of minor fixes for Beagleboard X15 which is now starting
to see a few more users in the wild"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (31 commits)
ARM: sti: dt: adapt DT to fix probe/bind issues in DRM driver
ARM: dts: fix omap2+ address translation for pbias
firmware: qcom: scm: Add function stubs for ARM64
ARM: dts: am57xx-beagle-x15: use palmas-usb for USB2
ARM: omap2plus_defconfig: enable GPIO_PCA953X
ARM: dts: omap5-uevm.dts: fix i2c5 pinctrl offsets
ARM: OMAP2+: AM43XX: Enable autoidle for clks in am43xx_init_late
ARM: dts: am57xx-beagle-x15: Update Phy supplies
ARM: pxa: balloon3: Fix build error
ARM: dts: Fixup model name for HP t410 dts
ARM: dts: DRA7: fix a typo in ethernet
ARM: omap2plus_defconfig: make PCF857x built-in
ARM: dts: Use ti,pbias compatible string for pbias
ARM: OMAP5: Cleanup options for SoC only build
ARM: DRA7: Select missing options for SoC only build
ARM: OMAP2+: board-generic: Remove stale of_irq macros
ARM: OMAP4+: PM: erratum is used by OMAP5 and DRA7 as well
ARM: dts: omap3-igep: Move eth IRQ pinmux to IGEPv2 common dtsi
ARM: dts: am57xx-beagle-x15: Add wakeup irq for mcp79410
ARM: dts: am335x-phycore-som: Fix mpu voltage
...
Add omap2_clk_enable_autoidle_all to am43xx_init_late otherwise the call
to omap2_clk_disable_autoidle_all in am43xx_init_early may cause some
clocks to always stay active and prevent low power mode transitions.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Most interrupt flow handlers do not use the irq argument. Those few
which use it can retrieve the irq number from the irq descriptor.
Remove the argument.
Search and replace was done with coccinelle and some extra helper
scripts around it. Thanks to Julia for her help!
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Julia Lawall <Julia.Lawall@lip6.fr>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
OMAP5 SoC has Cortex-A15 which does not use TWD timer. It uses
ARCH_TIMER instead, clean up unwanted configuration and enable
OMAP_INTERCONNECT and OPP which is necessary for expected functionality
on the SoC.
Reported-by: Carlos Hernandez <ceh@ti.com>
Reported-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
DRA7 does use OPP, uses OMAP interconnect and also does require SCU.
These are missing in the SoC only build of DRA7 breaking various PM
features in DRA7 only build.
Reported-by: Carlos Hernandez <ceh@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
When commit c4082d499f ("ARM: omap2+: board-generic: clean up the
irq data from board file") cleaned up the direct usage of gic_of_init
and omap_intc_of_init, it failed to clean up the macros properly.
Since these macros are no longer used, lets just remove them.
Fixes: c4082d499f ("ARM: omap2+: board-generic: clean up the irq data from board file")
Reported-by: Carlos Hernandez <ceh@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
OMAP5 and DRA7 reuse the same pm44xx_erratum variable so, enable the
same, else PM features such as Suspend to ram is broken in a SoC only
build configuration.
Reported-by: Carlos Hernandez <ceh@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Pull ARM development updates from Russell King:
"Included in this update:
- moving PSCI code from ARM64/ARM to drivers/
- removal of some architecture internals from global kernel view
- addition of software based "privileged no access" support using the
old domains register to turn off the ability for kernel
loads/stores to access userspace. Only the proper accessors will
be usable.
- addition of early fixup support for early console
- re-addition (and reimplementation) of OMAP special interconnect
barrier
- removal of finish_arch_switch()
- only expose cpuX/online in sysfs if hotpluggable
- a number of code cleanups"
* 'for-linus' of git://ftp.arm.linux.org.uk/~rmk/linux-arm: (41 commits)
ARM: software-based priviledged-no-access support
ARM: entry: provide uaccess assembly macro hooks
ARM: entry: get rid of multiple macro definitions
ARM: 8421/1: smp: Collapse arch_cpu_idle_dead() into cpu_die()
ARM: uaccess: provide uaccess_save_and_enable() and uaccess_restore()
ARM: mm: improve do_ldrd_abort macro
ARM: entry: ensure that IRQs are enabled when calling syscall_trace_exit()
ARM: entry: efficiency cleanups
ARM: entry: get rid of asm_trace_hardirqs_on_cond
ARM: uaccess: simplify user access assembly
ARM: domains: remove DOMAIN_TABLE
ARM: domains: keep vectors in separate domain
ARM: domains: get rid of manager mode for user domain
ARM: domains: move initial domain setting value to asm/domains.h
ARM: domains: provide domain_mask()
ARM: domains: switch to keeping domain value in register
ARM: 8419/1: dma-mapping: harmonize definition of DMA_ERROR_CODE
ARM: 8417/1: refactor bitops functions with BIT_MASK() and BIT_WORD()
ARM: 8416/1: Feroceon: use of_iomap() to map register base
ARM: 8415/1: early fixmap support for earlycon
...
ES2.0 is a minor variant of ES1.1. ES2.0 is an incremental revision
with various fixes including the following:
- reset logic fixes
- few assymetric aging logic fixes
- MMC clock rate fixes
- Ethernet speed fixes
- edma fixes for mcasp
NOTE: even though we use a compatible of dra742 and dra752, the usage in
the Linux kernel is more or less interchangable - we use dra752 more
often in the linux kernel compared to dra742 and 4.2-rc6
Signed-off-by: Vishal Mahaveer <vishalm@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Fix the warning:
arch/arm/mach-omap2/vc.c:302:47: warning: logical ‘or’ of collectively exhaustive tests is always true [-Wlogical-op]
As we're toggling both CLKREQ and OFFMODE, we should also be checking
OFFMODE.
Signed-off-by: Frans Klaver <fransklaver@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
When bringing up a new SoC we needlessly prevent booting at timer
init if timer clock_set_parent fails. This can fail if the system
is booting on bootloader configured PLL values until the clock
framework driver for the PLL is implemented.
Let's just WARN instead, this will provide helpful information
for anybody bringing up a new SoC what needs to be fixed.
This allows to boot dm814x that's still missing the PLL driver.
Signed-off-by: Tony Lindgren <tony@atomide.com>
This is the usual large batch of DT updates. Lots and lots of smaller
changes, some of the larger ones to point out are:
- Rockchip veyron (Chromebook) support, as well as several other new boards
- DRM support on Atmel AT91SAM9N12EK
- USB additions on some Allwinner platforms
- Mediatek MT6580 support
- Freescale i.MX6UL support
- Cleanups for Renesas shmobile platforms
- Lots of added devices on LPC18xx
- Lots of added devices and boards on UniPhier
There's also some dependent code added here, in particular some branches
that are primarily merged through the clock tree.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=D2Pm
-----END PGP SIGNATURE-----
Merge tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM DT updates from Olof Johansson:
"Ladies and gentlemen, we proudly announce to you the latest branch of
ARM device tree contents for the mainline kernel. Come and see, come
and see!
No less than twentythree thousand lines of additions! Just imagine the
joy you will have of using your mainline kernel on newly supported
hardware such as Rockchip Chromebooks, Freescale i.MX6UL boards or
UniPhier hardware!
For those of you feeling less adventurous, added hardware support on
platforms such as TI DM814x and Gumstix Overo platforms might be more
of your liking.
We've got something for everyone here!
Ahem. Cough. So, anyway...
This is the usual large batch of DT updates. Lots and lots of smaller
changes, some of the larger ones to point out are:
- Rockchip veyron (Chromebook) support, as well as several other new boards
- DRM support on Atmel AT91SAM9N12EK
- USB additions on some Allwinner platforms
- Mediatek MT6580 support
- Freescale i.MX6UL support
- cleanups for Renesas shmobile platforms
- lots of added devices on LPC18xx
- lots of added devices and boards on UniPhier
There's also some dependent code added here, in particular some
branches that are primarily merged through the clock tree"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (389 commits)
ARM: tegra: Add gpio-ranges property
ARM: tegra: Fix AHB base address on Tegra20, Tegra30 and Tegra114
ARM: tegra: Add Tegra124 PMU support
ARM: tegra: jetson-tk1: Add GK20A GPU DT node
ARM: tegra: venice2: Add GK20A GPU DT node
ARM: tegra: Add IOMMU node to GK20A
ARM: tegra: Add CPU regulator to the Jetson TK1 device tree
ARM: tegra: Add entries for cpufreq on Tegra124
ARM: tegra: Enable the DFLL on the Jetson TK1
ARM: tegra: Add the DFLL to Tegra124 device tree
ARM: dts: zynq: Add devicetree entry for Xilinx Zynq reset controller.
ARM: dts: UniPhier: fix PPI interrupt CPU mask of timer nodes
ARM: dts: rockchip: correct regulator power states for suspend
ARM: dts: rockchip: correct regulator PM properties
ARM: dts: vexpress: Use assigned-clock-parents for sp810
pinctrl: tegra: Only set the gpio range if needed
arm: boot: dts: am4372: add ARM timers and SCU nodes
ARM: dts: AM4372: Add the am4372-rtc compatible string
ARM: shmobile: r8a7794 dtsi: Add CPG/MSTP Clock Domain
ARM: shmobile: r8a7793 dtsi: Add CPG/MSTP Clock Domain
...
New or improved SoC support:
- Addition of support for Atmel's SAMA5D2 SoC
- Addition of Freescale i.MX6UL
- Improved support of TI's DM814x platform
- Misc fixes and improvements for RockChip platforms
- Marvell MVEBU suspend/resume support
A few driver changes that ideally would belong in the drivers branch are
also here (acked by appropriate maintainers):
- Power key input driver for Freescale platforms (svns)
- RTC driver updates for Freescale platforms (svns/mxc)
- Clk fixes for TI DM814/816X
+ a bunch of other changes for various platforms
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=8T5Z
-----END PGP SIGNATURE-----
Merge tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC platform updates from Olof Johansson:
"New or improved SoC support:
- add support for Atmel's SAMA5D2 SoC
- add support for Freescale i.MX6UL
- improved support for TI's DM814x platform
- misc fixes and improvements for RockChip platforms
- Marvell MVEBU suspend/resume support
A few driver changes that ideally would belong in the drivers branch
are also here (acked by appropriate maintainers):
- power key input driver for Freescale platforms (svns)
- RTC driver updates for Freescale platforms (svns/mxc)
- clk fixes for TI DM814/816X
+ a bunch of other changes for various platforms"
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (83 commits)
ARM: rockchip: pm: Fix PTR_ERR() argument
ARM: imx: mach-imx6ul: Fix allmodconfig build
clk: ti: fix for definition movement
ARM: uniphier: drop v7_invalidate_l1 call at secondary entry
memory: kill off set_irq_flags usage
rtc: snvs: select option REGMAP_MMIO
ARM: brcmstb: select ARCH_DMA_ADDR_T_64BIT for LPAE
ARM: BCM: Enable ARM erratum 798181 for BRCMSTB
ARM: OMAP2+: Fix power domain operations regression caused by 81xx
ARM: rockchip: enable PMU_GPIOINT_WAKEUP_EN when entering shallow suspend
ARM: rockchip: set correct stabilization thresholds in suspend
ARM: rockchip: rename osc_switch_to_32k variable
ARM: imx6ul: add fec MAC refrence clock and phy fixup init
ARM: imx6ul: add fec bits to GPR syscon definition
rtc: mxc: add support of device tree
dt-binding: document the binding for mxc rtc
rtc: mxc: use a second rtc clock
ARM: davinci: cp_intc: use IRQCHIP_SKIP_SET_WAKE instead of irq_set_wake callback
soc: mediatek: Fix SCPSYS compilation
ARM: at91/soc: add basic support for new sama5d2 SoC
...
A large cleanup branch this release, with a healthy 10k negative line delta.
Most of this is removal of legacy (non-DT) support of shmobile
platforms. There is also removal of two non-DT platforms on OMAP,
and the plat-samsung directory is cleaned out by moving most of the
previously shared-location-but-not-actually-shared files from there to
the appropriate mach directories instead.
There are other sets of changes in here as well:
- Rob Herring removed use of set_irq_flags under all platforms and
moved to genirq alternatives
- A series of timer API conversions to set-state interface
- ep93xx, nomadik and ux500 cleanups from Linus Walleij
- __init annotation fixes from Nicolas Pitre
+ a bunch of other changes that all add up to a nice set of cleanups
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJV16zRAAoJEIwa5zzehBx30OYQAIM2TaHWxDzcK0jOfrPEOyU0
jhnT3B2/FbIpYbt3UwcDOqJacHzA/syU4UjplCcWWhKYtTucXQIjOxi0BgRq5V3X
EFrgEbQMLXshhMGquBd4Nl6XhpRrlZcnnY4iFPGf7pR5jQfwQhZCiHEOXCLe4qlz
m9GorKjEmiSk2ID/PFpyOUx20XiiqkU2MOCsNqNiGwFfmQfpVo0vXtKgxlL6d6q+
9mrWFFTqgiOBMAU/X1j18U9jpFT6NOe8JcXp3F3tm4Cq5nJ2pTPZcaYWOORD0bGc
7Os1HRTN9SMNsb8sSvQa1N/Fy2AAFuvGdg8q4oLzgtXJogInRmxE4oGLbffq0As/
q81mEuWkdHjGPs5oyPNQdP2grYhflNP+M1+fA6QaUG/mDl5RFFcld9nfhCiBeIZW
oHAHZhz7//BImpFsmNiXOew9fmQaHxQ6Jy0K4YvhqaxwQ0N54ZadUPH47wmmxW5E
X5IY5Oo7xg3e4EU4/t1nFDTxMG936ZxLVtuq79dRHrl+AT6KVbzdUI4LLyrvEULh
ETbWIZUAHvE9i2N8GbsfDzc9YlpG/c5SpN8T5dg2R0BQpgE192iG6s5XoGyu80MG
MbtbEBml0y3tr36Bd9tCpsSrBjzZLUk5WRo6Rd/zWKlRkslV74iacKLvC7C5oa7n
GYL4xUSPE1RhJxnXezp0
=acy4
-----END PGP SIGNATURE-----
Merge tag 'armsoc-cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC cleanups from Olof Johansson:
"A large cleanup branch this release, with a healthy 10k negative line
delta.
Most of this is removal of legacy (non-DT) support of shmobile
platforms. There is also removal of two non-DT platforms on OMAP, and
the plat-samsung directory is cleaned out by moving most of the
previously shared-location-but-not-actually-shared files from there to
the appropriate mach directories instead.
There are other sets of changes in here as well:
- Rob Herring removed use of set_irq_flags under all platforms and
moved to genirq alternatives
- a series of timer API conversions to set-state interface
- ep93xx, nomadik and ux500 cleanups from Linus Walleij
- __init annotation fixes from Nicolas Pitre
+ a bunch of other changes that all add up to a nice set of cleanups"
* tag 'armsoc-cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (108 commits)
ARM/fb: ep93xx: switch framebuffer to use modedb only
ARM: gemini: Setup timer3 as free running timer
ARM: gemini: Use timer1 for clockevent
ARM: gemini: Add missing register definitions for gemini timer
ARM: ep93xx/timer: Migrate to new 'set-state' interface
ARM: nomadik: push accelerometer down to boards
ARM: nomadik: move l2x0 setup to device tree
ARM: nomadik: selectively enable UART0 on boards
ARM: nomadik: move hog code to use DT hogs
ARM: shmobile: Fix mismerges
ARM: ux500: simplify secondary CPU boot
ARM: SAMSUNG: remove keypad-core header in plat-samsung
ARM: SAMSUNG: local watchdog-reset header in mach-s3c64xx
ARM: SAMSUNG: local onenand-core header in mach-s3c64xx
ARM: SAMSUNG: local irq-uart header in mach-s3c64xx
ARM: SAMSUNG: local backlight header in mach-s3c64xx
ARM: SAMSUNG: local ata-core header in mach-s3c64xx
ARM: SAMSUNG: local regs-usb-hsotg-phy header in mach-s3c64xx
ARM: SAMSUNG: local spi-core header in mach-s3c24xx
ARM: SAMSUNG: local nand-core header in mach-s3c24xx
...
and the addition of new clock drivers. Stephen Boyd has also done a lot
of subsystem-wide driver clean-ups (thanks!). There are also fixes to
the framework core and changes to better split clock provider drivers
from clock consumer drivers.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=QAiQ
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus-4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Michael Turquette:
"The clk framework changes for 4.3 are mostly updates to existing
drivers and the addition of new clock drivers. Stephen Boyd has also
done a lot of subsystem-wide driver clean-ups (thanks!). There are
also fixes to the framework core and changes to better split clock
provider drivers from clock consumer drivers"
* tag 'clk-for-linus-4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (227 commits)
clk: s5pv210: add missing call to samsung_clk_of_add_provider()
clk: pistachio: correct critical clock list
clk: pistachio: Fix PLL rate calculation in integer mode
clk: pistachio: Fix override of clk-pll settings from boot loader
clk: pistachio: Fix 32bit integer overflows
clk: tegra: Fix some static checker problems
clk: qcom: Fix MSM8916 prng clock enable bit
clk: Add missing header for 'bool' definition to clk-conf.h
drivers/clk: appropriate __init annotation for const data
clk: rockchip: register pll mux before pll itself
clk: add bindings for the Ux500 clocks
clk/ARM: move Ux500 PRCC bases to the device tree
clk: remove duplicated code with __clk_set_parent_after
clk: Convert __clk_get_name(hw->clk) to clk_hw_get_name(hw)
clk: Constify clk_hw argument to provider APIs
clk: Hi6220: add stub clock driver
dt-bindings: clk: Hi6220: Document stub clock driver
dt-bindings: arm: Hi6220: add doc for SRAM controller
clk: atlas7: fix pll missed divide NR in fraction mode
clk: atlas7: fix bit field and its root clk for coresight_tpiu
...
We're removing struct clk from the clk provider API, so switch to
clk_get_rate() and clk_hw_get_rate() here appropriately.
Acked-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The conversion of the wakeupgen irqchip to hierarchical irq domains
failed to provide a mechanism to properly set the trigger type of an
interrupt.
The wakeupgen irq chip itself has no mechanism and therefor no
irq_set_type() callback. The code before the conversion relayed the
trigger configuration directly to the underlying GIC.
Restore the correct behaviour by setting the wakeupgen irq_set_type
callback to irq_chip_set_type_parent(). This propagates the
set_trigger() call to the underlying GIC irqchip.
[ tglx: Massaged changelog ]
Fixes: 7136d457f3 ('ARM: omap: convert wakeupgen to stacked domains')
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Cc: Sudeep Holla <sudeep.holla@arm.com>
Cc: <linux@arm.linux.org.uk>
Cc: <nsekhar@ti.com>
Cc: <jason@lakedaemon.net>
Cc: <balbi@ti.com>
Cc: <linux-arm-kernel@lists.infradead.org>
Cc: <marc.zyngier@arm.com>
Cc: stable@vger.kernel.org # 4.1
Link: http://lkml.kernel.org/r/1439554830-19502-5-git-send-email-grygorii.strashko@ti.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
I managed to mess up omap3 power domain operations with commit
7c80a3f89c ("ARM: OMAP2+: Add custom prwdm_operations for 81xx
to support dm814x"), by default we should keep on using the
omap3_pwrdm_operations, only 81xx needs custom handling.
This causes omap3 PM to break so we won't hit off mode any longer
causing idle power consumption go up from less than 10mW to over
50 mW.
Fixs: 7c80a3f89c ("ARM: OMAP2+: Add custom prwdm_operations for
81xx to support dm814x")
Signed-off-by: Tony Lindgren <tony@atomide.com>
* fixes: (28 commits)
ARM: ux500: add an SMP enablement type and move cpu nodes
ARM: dts: keystone: fix dt bindings to use post div register for mainpll
ARM: nomadik: disable UART0 on Nomadik boards
ARM: dts: i.MX35: Fix can support.
ARM: OMAP2+: hwmod: Fix _wait_target_ready() for hwmods without sysc
ARM: dts: add CPU OPP and regulator supply property for exynos4210
ARM: dts: Update video-phy node with syscon phandle for exynos3250
ARM: keystone: dts: rename pcie nodes to help override status
ARM: keystone: dts: fix dt bindings for PCIe
ARM: pxa: fix dm9000 platform data regression
ARM: DRA7: hwmod: fix gpmc hwmod
ARM: dts: Correct audio input route & set mic bias for am335x-pepper
ARM: OMAP2+: Add HAVE_ARM_SCU for AM43XX
MAINTAINERS: digicolor: add dts files
ARM: ux500: fix MMC/SD card regression
ARM: ux500: define serial port aliases
ARM: dts: OMAP5: Add #iommu-cells property to IOMMUs
ARM: dts: OMAP4: Add #iommu-cells property to IOMMUs
ARM: dts: Fix frequency scaling on Gumstix Pepper
ARM: dts: configure regulators for Gumstix Pepper
...
* cleanup-clk-h-includes: (62 commits)
clk: Remove clk.h from clk-provider.h
clk: h8300: Remove clk.h and clkdev.h includes
clk: at91: Include clk.h and slab.h
clk: ti: Switch clk-provider.h include to clk.h
clk: pistachio: Include clk.h
clk: ingenic: Include clk.h
clk: si570: Include clk.h
clk: moxart: Include clk.h
clk: cdce925: Include clk.h
clk: Include clk.h in clk.c
clk: zynq: Include clk.h
clk: ti: Include clk.h
clk: sunxi: Include clk.h and remove unused clkdev.h includes
clk: st: Include clk.h
clk: qcom: Include clk.h
clk: highbank: Include clk.h
clk: bcm: Include clk.h
clk: versatile: Remove clk.h and clkdev.h includes
clk: ux500: Remove clk.h and clkdev.h includes
clk: tegra: Properly include clk.h
...
From Tero Kristo:
"This pull request contains the TI clock driver set to move the
clock implementations under clock driver. Some small portions of
the clock driver code still remain under mach-omap2 after this,
it should be decided whether this code is now obsolete and should
be deleted or should someone try to fix it."
Slight merge conflicts with determine_rate prototype changes.
Init data marked const should be annotated with __initconst for
correctness and not __initdata. In some cases the array gathering
references to that data has to be marked const as well. This fixes
LTO builds that otherwise fail with section mismatch errors.
Signed-off-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Clock rates are stored in an unsigned long field, but ->determine_rate()
(which returns a rounded rate from a requested one) returns a long
value (errors are reported using negative error codes), which can lead
to long overflow if the clock rate exceed 2Ghz.
Change ->determine_rate() prototype to return 0 or an error code, and pass
a pointer to a clk_rate_request structure containing the expected target
rate and the rate constraints imposed by clk users.
The clk_rate_request structure might be extended in the future to contain
other kind of constraints like the rounding policy, the maximum clock
inaccuracy or other things that are not yet supported by the CCF
(power consumption constraints ?).
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
CC: Jonathan Corbet <corbet@lwn.net>
CC: Tony Lindgren <tony@atomide.com>
CC: Ralf Baechle <ralf@linux-mips.org>
CC: "Emilio López" <emilio@elopez.com.ar>
CC: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Tero Kristo <t-kristo@ti.com>
CC: Peter De Schrijver <pdeschrijver@nvidia.com>
CC: Prashant Gaikwad <pgaikwad@nvidia.com>
CC: Stephen Warren <swarren@wwwdotorg.org>
CC: Thierry Reding <thierry.reding@gmail.com>
CC: Alexandre Courbot <gnurou@gmail.com>
CC: linux-doc@vger.kernel.org
CC: linux-kernel@vger.kernel.org
CC: linux-arm-kernel@lists.infradead.org
CC: linux-omap@vger.kernel.org
CC: linux-mips@linux-mips.org
CC: linux-tegra@vger.kernel.org
[sboyd@codeaurora.org: Fix parent dereference problem in
__clk_determine_rate()]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Tested-by: Romain Perier <romain.perier@gmail.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
[sboyd@codeaurora.org: Folded in fix from Heiko for fixed-rate
clocks without parents or a rate determining op]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Two fixes against v4.2-rc1. The first, for DRA7xx platforms,
corrects some incorrect GPMC hardware description data. The
second one will ensure that the hwmod code will wait for any
module with CPU-accessible registers to become ready before
attempting to access it.
Basic build, boot, and PM test logs are available here:
http://www.pwsan.com/omap/testlogs/omap-hwmod-a-for-v4.2-rc/20150723065408/
Note that I do not have a DRA7xx or AM43xx board, and therefore
cannot test on those platforms.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJVsPJKAAoJEMePsQ0LvSpLtgsQAKT6RZ7pfQMgf6RjY4xDuQwJ
qiCgLKvj0gohSkpE0AG7DOPxIMNOfH79Fa44kjv/MtxBcmKiAztPCUhQYbWaNYPI
O5fBI0uYY9i1RYQQ0H2SGzEstXMjuJn9w8Fhq60vbC0bjrAC1rKSIm+t0iO1O02T
zVc7mto68vJQbh9tp2GwY9BXq8nbhI8fxi3+wIQhsMN+PWAAf6YQPZFjRGCZWZFA
ipH01kfYC2/iQF4h5tkFnasTPeWJs3H8ENrM+uW3PPOd6Q4TVf+KslW7Has+MJcn
4RFjdMkDCGfY1KxfsLtq9dsCFzZ8wLX/PfibAlgAnp8hyZyHMpGhSfCZQK3xK6L0
orQ5CQwwInzKCxGZCc57L80RI+KX8Z8LjUoTmwpIUCY705vPNukU4sWQqD0cMvv7
21XffSC+ak9edF5PYAUJTuRa1XiFOXn3dwNd98gANuUa21tEGnBtqT688eQMPlOG
oprIITSjFASmE2iKhvNvr8+IyWacu7TBKGglKSWILcrdgGhxLUyrjcsScYu+E4lG
pVyFzo1tz8HZgiwFYTEVZe8qFlMCYYgcbB/UxaNeox6A99S4eRPvLjevgBvDyEtP
d3GxHkpzfxA8jCWRxquHTwIDAmpTWaVnT42oU83oZHuf2CUn1gY5DJDmWgk9C552
ifw1tQPE/Jh4cmX2ayMw
=dgbc
-----END PGP SIGNATURE-----
Merge tag 'for-v4.2-rc/omap-fixes-a' of git://git.kernel.org/pub/scm/linux/kernel/git/pjw/omap-pending into fixes
Merge "ARM: OMAP2+: hwmod fixes for v4.2-rc" from Paul Walmsley:
ARM: OMAP2+: hwmod fixes for v4.2-rc
Two fixes against v4.2-rc1. The first, for DRA7xx platforms,
corrects some incorrect GPMC hardware description data. The
second one will ensure that the hwmod code will wait for any
module with CPU-accessible registers to become ready before
attempting to access it.
Basic build, boot, and PM test logs are available here:
http://www.pwsan.com/omap/testlogs/omap-hwmod-a-for-v4.2-rc/20150723065408/
Note that I do not have a DRA7xx or AM43xx board, and therefore
cannot test on those platforms.
* tag 'for-v4.2-rc/omap-fixes-a' of git://git.kernel.org/pub/scm/linux/kernel/git/pjw/omap-pending:
ARM: OMAP2+: hwmod: Fix _wait_target_ready() for hwmods without sysc
ARM: DRA7: hwmod: fix gpmc hwmod
Signed-off-by: Olof Johansson <olof@lixom.net>
Restore the OMAP4 barrier behaviour using the new implementation which
allows multiplatform systems to hook into the mb() and wmb() ARM
implementations to perform any necessary additional barrier maintanence.
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Richard Woodruff <r-woodruff2@ti.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This reverts commit 606da4826b.
We actually need this code for proper behaviour of OMAP4, and it needs
fixing a different way other than just removing the code. Disabling
code which is necessary in the hopes of persuing multiplatform kernels
is a stupid approach.
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Richard Woodruff <r-woodruff2@ti.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Similar to commit fdf4850cb5 ("ARM: BCM5301X: workaround suppress fault"),
let's add custom handling for the aborts on t410 that prevent booting:
Unhandled fault: imprecise external abort (0xc06) at 0xee091fb0
pgd = ee4bc000
[ee091fb0] *pgd=ae00041e(bad)
Kernel panic - not syncing: Attempted to kill init! exitcode=0x00000007
Cc: Matthijs van Duin <matthijsvanduin@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Let's add minimal set of dm814x hwmods to have a bootable system.
Cc: Matthijs van Duin <matthijsvanduin@gmail.com>
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Let's change the defines so we can share the hwmod code better between
dm816x and dm814x, and let's add the dm814x specific defines. And let's
rename the shared ones to start with dm81xx. No functional changes.
Cc: Matthijs van Duin <matthijsvanduin@gmail.com>
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This series adds:
- I/O wakeup support for AM43xx
- register lock and unlock support to the hwmod code (needed for the RTC
IP blocks on some chips)
- several fixes for sparse warnings and an unnecessary null pointer test
- a DRA7xx clockdomain configuration workaround, to deal with some hardware
bugs
Basic build, boot, and PM tests are here:
http://www.pwsan.com/omap/testlogs/hwmod-prcm-for-v4.3/20150723080012/
Since I do not have an AM43xx or DRA7xx device, I can't test on those
platforms.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=dZvv
-----END PGP SIGNATURE-----
Merge tag 'for-v4.3/omap-hwmod-prcm-a' of git://git.kernel.org/pub/scm/linux/kernel/git/pjw/omap-pending into omap-for-v4.3/soc
ARM: OMAP2+: PRCM and hwmod changes for v4.3
This series adds:
- I/O wakeup support for AM43xx
- register lock and unlock support to the hwmod code (needed for the RTC
IP blocks on some chips)
- several fixes for sparse warnings and an unnecessary null pointer test
- a DRA7xx clockdomain configuration workaround, to deal with some hardware
bugs
Basic build, boot, and PM tests are here:
http://www.pwsan.com/omap/testlogs/hwmod-prcm-for-v4.3/20150723080012/
Since I do not have an AM43xx or DRA7xx device, I can't test on those
platforms.
Enable IO wakeup feature. This enables am437x pads to generate daisy
chained wake ups(eventually generates aprcm Interrupt) especially
when in low power modes.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Reviewed-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
The register offsets for some of the PRM Registers are different
hence populating the differing fields. This is needed to support
IO wake up feature for am437x family.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Reviewed-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
The register offsets of IRQENABLE_MPU_2 and IRQSTATUS_MPU_2 are hardcoded.
This makes it difficult to reuse the code for SoCs like AM437x that have
a single instance of IRQENABLE_MPU and IRQSTATUS_MPU registers.
Hence handling the case using offset of 4 to accommodate single set of IRQ*
registers generically.
Signed-off-by: Keerthy <j-keerthy@ti.com>
[paul@pwsan.com: fixed whitespace alignment problems reported by checkpatch.pl]
Reviewed-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Add the PRM IRQ register offsets. This is needed to support PRM I/O
wakeup on AM43xx.
Signed-off-by: Keerthy <j-keerthy@ti.com>
[paul@pwsan.com: improved patch description, moved the PRM_IO_PMCTRL macro
out of the CM section]
Reviewed-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
PRM_IO_PMCTRL_OFFSET need not be same for all SOCs hence
remove hardcoding and use the value provided by the omap_prcm_irq_setup
structure. This is done to support IO wakeup on am437x series.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Reviewed-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
dropping the board files for omap3logic and omap3pandora.
The reason for dropping these now rather than later is that now
we can simply revert the patches in case of unexpected issues as
we are not dropping any platform data at this point.
This leaves us with only the following board-*.c files:
BOARD REASON NEEDED
board-ldp.c Still used in RMKs boot test system
board-rx51-*.c Needs /proc/atags support for user space
Once we have the n900 legacy user space issues sorted out for
/proc/atags and system_rev, we can drop the remaining two
board-*.c files. And then one merge window after that we can
drop the legacy booting support assuming no unexpected issues
are found.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=3+Gh
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.3/legacy-v2-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/cleanup
Merge "drop few more legacy boards for v4.3" from Tony Lindgren:
Drop more omap3 legacy board-*.c files for v4.3. This time we're
dropping the board files for omap3logic and omap3pandora.
The reason for dropping these now rather than later is that now
we can simply revert the patches in case of unexpected issues as
we are not dropping any platform data at this point.
This leaves us with only the following board-*.c files:
BOARD REASON NEEDED
board-ldp.c Still used in RMKs boot test system
board-rx51-*.c Needs /proc/atags support for user space
Once we have the n900 legacy user space issues sorted out for
/proc/atags and system_rev, we can drop the remaining two
board-*.c files. And then one merge window after that we can
drop the legacy booting support assuming no unexpected issues
are found.
* tag 'omap-for-v4.3/legacy-v2-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: Remove legacy booting support for Pandora
ARM: OMAP2+: Remove legacy booting support for LogicPD Torpedo
Signed-off-by: Olof Johansson <olof@lixom.net>
Add wl1251 support via pdata-quirks as it's driver lacks DT
support. MMC3 is marked disabled in DT so that MMC3 instance of
hsmmc driver is probed using platform data with special card init
callback.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add backlight support via pdata-quirks as it's driver lacks DT support.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
These files use the consumer API, so include clk.h explicitly.
Acked-by: Tero Kristo <t-kristo@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Migrate omap2 driver to the new 'set-state' interface provided by
clockevents core, the earlier 'set-mode' interface is marked obsolete
now.
This also enables us to implement callbacks for new states of clockevent
devices, for example: ONESHOT_STOPPED.
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
We've been moving all omap2+ based systems to boot in device tree only
mode for a few years now. Only omap3 has legacy booting support
remaining. Most omap3 boards already have related arch/arm/boot/*.dts*
files for booting with device tree.
This board has support for device tree based booting, and we've been
printing warnings about the legacy booting being deprecated for a
few merge cycles now. Let's attempt to remove the legacy booting
for it.
The reason for removing the legacy booting support now rather than
later is we can simply revert this patch if necessary if we run
into some unexpected issues that are not trivial to fix for the
device tree based booting.
Cc: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Let's add a minimal clocks for dm814x to get it booted. This is
mostly a placeholder and relies on the PLLs being on from the
bootloader.
Note that the divider clocks work the same way as on dm816x and
am335x.
Cc: Matthijs van Duin <matthijsvanduin@gmail.com>
Cc: Mike Turquette <mturquette@linaro.org>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: Tero Kristo <t-kristo@ti.com>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Looking at the TI kernel tree I noticed that dm81xx need custom
ti81xx_pwrdm_operations. Let's also change dm816x over to use them
as the registers are different for dm81xx compared to others.
Cc: Matthijs van Duin <matthijsvanduin@gmail.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
For now, let's just add the ones shared with dm816x.
The dm814x specific ones can be added as they are tested.
Cc: Matthijs van Duin <matthijsvanduin@gmail.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The OMAP IOMMU driver has been adapted to the IOMMU framework
for a while now, and it no longer supports being built as a
module. Cleanup all the module related references both from
the code and in the build.
While at it, also relocate a comment around the initcall to
avoid a checkpatch strict warning about using a blank line
after function/struct/union/enum declarations.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
DRA7 uses OMAP5 IO table at the moment. This is purely spurious since
the OMAP5 and DRA7 register maps are different in many aspects.
AM57xx/DRA7 TRM Reference: http://www.ti.com/lit/ug/spruhz6/spruhz6.pdf
NOTE: Most of the drivers are already doing ioremap, so, there should'nt
be any functional improvement involved here, other than making the
initial iotable more accurate.
Fixes: a3a9384a11 ("ARM: DRA7: Reuse io tables and add a new .init_early")
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Inspired by a patch from Felipe Balbi <balbi@ti.com>, we can
now get rid of most the code in omap4_local_timer_init.
Omap4 is now device tree only.. And we have not properly supported
omap4 ES1.0 revision for a really long time AFAIK.
Let's just remove all that code to simplify things. This assumes
we have arm,cortex-a9-twd-timer entry in the omap4.dtsi file, which
we do.
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The of_node_put() function tests whether its argument is NULL and then
returns immediately if so. Furthermore, the kerneldoc for
of_node_put() explicitly supports passing in a NULL pointer as its
argument. Thus the test around the call is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
[paul@pwsan.com: dropped the omap_device.c and omap_hwmod.c changes for
now, edited the commit message accordingly and to note the documented
"contract"]
Reviewed-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
omap3xxx_restart() and omap44xx_restart() are global
functions declared in common.h. Include this file
in omap3-restart.c and omap4-restart.c to prevent
sparse warnings of type:
arch/arm/mach-omap2/omap4-restart.c:22:6: warning: symbol 'omap44xx_restart' was not declared. Should it be static?
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Reviewed-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Add missing static declaration for file local variables.
This fixes sparse warnings of type:
arch/arm/mach-omap2/omap_hwmod_81xx_data.c:491:26: warning: symbol 'dm81xx_alwon_l3_slow__gpmc' was not declared. Should it be static?
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Some IP blocks like RTC, needs an additional setting for writing to its
registers. This is to prevent any spurious writes from changing the
register values.
This patch adds optional lock and unlock function pointers to
the IP block's hwmod data. These unlock and lock function pointers
are called by hwmod code before and after writing sysconfig registers.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
[paul@pwsan.com: fixed indentation level to conform with the rest of the
structure members]
Reviewed-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
GPMC smart idle is not really broken but it does not support
smart idle with wakeup.
Fixes: 556708fe87 ("ARM: OMAP: DRA7: hwmod: Make gpmc software supervised as the smart idle is broken")
Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Legacy IPs like PWMSS, present under l4per2_7xx_clkdm, cannot support
smart-idle when its clock domain is in HW_AUTO on DRA7 SoCs. Hence,
program clock domain to SW_WKUP.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Acked-by: Tero Kristo <t-kristo@ti.com>
Reviewed-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: <stable@vger.kernel.org>
CONFIG_HAVE_ARM_SCU only gets selected if CONFIG_SMP is selected in an OMAP
system, however AM43XX needs this option regardless of CONFIG_SMP and also
for an AM43XX only build as it is important for controlling power in the SoC.
Without this we cannot suspend the CPU for SoC suspend or cpuidle. The
ARM Cortex A9 needs SCU CPU Power Status bits to be set to off mode in order
for the PRCM to transition the MPU to low power modes.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Use pdata-quirks to provide platform data required for reset
management during boot and shutdown of the wkup_m3 processor
on both the AM33xx and AM43xx SoCs. The WkupM3 remote processor
is used to implement and achieve low-power functionality on
the AM33xx & AM43xx SoCs.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We've been moving all omap2+ based systems to boot in device tree only
mode for a few years now. Only omap3 has legacy booting support
remaining. Most omap3 boards already have related arch/arm/boot/*.dts*
files for booting with device tree.
This board has support for device tree based booting, and we've been
printing warnings about the legacy booting being deprecated for a
few merge cycles now. Let's attempt to remove the legacy booting
for it.
The reason for removing the legacy booting support now rather than
later is we can simply revert this patch if necessary if we run
into some unexpected issues that are not trivial to fix for the
device tree based booting.
Cc: Tim Nordell <tim.nordell@logicpd.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
- OMAP hwspinlock DT support from Suman Anna
- QCOM hwspinlock DT support from Bjorn Andersson
- a new CSR atlas7 hwspinlock driver from Wei Chen
- CSR atlas7 hwspinlock DT binding document from Wei Chen
- a tiny QCOM hwspinlock driver fix from Bjorn Andersson
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=2HLz
-----END PGP SIGNATURE-----
Merge tag 'hwspinlock-4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/ohad/hwspinlock
Pull hwspinlock updates from Ohad Ben-Cohen:
- hwspinlock core DT support from Suman Anna
- OMAP hwspinlock DT support from Suman Anna
- QCOM hwspinlock DT support from Bjorn Andersson
- a new CSR atlas7 hwspinlock driver from Wei Chen
- CSR atlas7 hwspinlock DT binding document from Wei Chen
- a tiny QCOM hwspinlock driver fix from Bjorn Andersson
* tag 'hwspinlock-4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/ohad/hwspinlock:
hwspinlock: qcom: Correct msb in regmap_field
DT: hwspinlock: add the CSR atlas7 hwspinlock bindings document
hwspinlock: add a CSR atlas7 driver
hwspinlock: qcom: Add support for Qualcomm HW Mutex block
DT: hwspinlock: Add binding documentation for Qualcomm hwmutex
hwspinlock/omap: add support for dt nodes
Documentation: dt: add the omap hwspinlock bindings document
hwspinlock/core: add device tree support
Documentation: dt: add common bindings for hwspinlock
As usual, quite a few device-tree updates in ARM land. There was ome
minor churn in DTs due to relicensing under a dual-license, and lots
of little additions of new peripherals, features etc, but nothing
really exciting to call to your attention. Some higlights, focsuing
on support for new SoCs and boards:
- AT91: new boards: Overkiz, Acme Systems' Arietta G25
- tegra: HDA support
- bcm: new platforms: Buffalo WXR-1900DHP, SmartRG SR400ac, ASUS RT-AC87U
- mvebu: new platforms: Compulab CM-A510, Armada 385-based Linksys
boards, DLink DNS-327L
- OMAP: new platforms: Baltos IR5221, LogicPD Torpedo, Toby-Churchill SL50
- ARM: added support for Juno r1 board
- sunxi: A33 SoC support; new boards: A23 EVB, SinA33, GA10H-A33, Mele A1000G
- imx: i.MX7D SoC support; new boards: Armadeus Systems APF6,
Gateworks GW5510, and aristainetos2 boards
- hisilicon: hi6220 SoC support; new boards: 96boards hikey
Conflicts: None
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=wWIc
-----END PGP SIGNATURE-----
Merge tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC DT updates from Kevin Hilman:
"As usual, quite a few device-tree updates in ARM land. There was one
minor churn in DTs due to relicensing under a dual-license, and lots
of little additions of new peripherals, features etc, but nothing
really exciting to call to your attention. Some higlights, focsuing
on support for new SoCs and boards:
- AT91: new boards: Overkiz, Acme Systems' Arietta G25
- tegra: HDA support
- bcm: new platforms: Buffalo WXR-1900DHP, SmartRG SR400ac, ASUS
RT-AC87U
- mvebu: new platforms: Compulab CM-A510, Armada 385-based Linksys
boards, DLink DNS-327L
- OMAP: new platforms: Baltos IR5221, LogicPD Torpedo, Toby-Churchill
SL50
- ARM: added support for Juno r1 board
- sunxi: A33 SoC support; new boards: A23 EVB, SinA33, GA10H-A33,
Mele A1000G
- imx: i.MX7D SoC support; new boards: Armadeus Systems APF6,
Gateworks GW5510, and aristainetos2 boards
- hisilicon: hi6220 SoC support; new boards: 96boards hikey"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (462 commits)
ARM: hisi: revert changes from hisi/hip04-dt branch
ARM: nomadik: set proper compatible for accelerometer
ARM64: juno: add GPIO keys
ARM: at91/dt: sama5d4: fix dma conf for aes, sha and tdes nodes
ARM: dts: Introduce STM32F429 MCU
ARM: socfpga: dts: enable ethernet for Arria10 devkit
ARM: dts: k2l: fix the netcp range size
ARM: dts: k2e: fix the netcp range size
ARM: dts: k2hk: fix the netcp range size
ARM: dts: k2l-evm: Add device bindings for netcp driver
ARM: dts: k2e-evm: Add device bindings for netcp driver
ARM: dts: k2hk-evm: Add device bindings for netcp driver
ARM: BCM5301X: Add DT for Asus RT-AC87U
ARM: BCM5301X: add IRQ numbers for PCIe controller
ARM: BCM5301X: add NAND flash chip description
arm64: dts: Add dts files for Hisilicon Hi6220 SoC
clk: hi6220: Document devicetree bindings for hi6220 clock
arm64: hi6220: Document devicetree bindings for Hisilicon hi6220 SoC
ARM: at91/dt: sama5d4ek: mci0 uses slot 0
ARM: at91/dt: kizbox: fix mismatch LED PWM device
...
Our SoC branch usually contains expanded support for new SoCs and
other core platform code. Some highlights from this round:
- sunxi: SMP support for A23 SoC
- socpga: big-endian support
- pxa: conversion to common clock framework
- bcm: SMP support for BCM63138
- imx: support new I.MX7D SoC
- zte: basic support for ZX296702 SoC
Conflicts:
arch/arm/mach-socfpga/core.h
Trivial remove/remove conflict with our cleanup branch.
Resolution: remove both sides
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJVi4RMAAoJEFk3GJrT+8Zl6/kP/1Rv9O++1Kxua6R54Og6AF1J
0miFr2fnUrUWUYg/NVbseRH5bBe6N6ir3SQMfde8W2/QibEjOoEwSwrle+mC/eiq
CE0x0gtyRvXMrMU/FWkOvbmmw9uv5oz1z3IHZV6AiecNuSMLUBPfamryikQ8C+d1
O/QZtX543tJQJDOBihO5cuhoVVM37UX0unNmqGsyswlyqTPF8FxcIJAYVNtnxjmj
AFaOB0nDJKLKFTiX2Ype2wOxxJX1lrLatNo4W4T+YaaK+i1uCOhgTdSN+n49K7YA
KNDFEgZFQqT8VMJyG+eJVeYF+cI7yWQ7lBzIftPUjPk/7+dIHBjWPz2QdjVz3U38
kxncf4S9xGAF5G2rcKe4mFrfT3Y8QLWQpA/jFs06yLwW1O3Hlfq3DzMdGNcF7hth
17LOP8namn9+NepZEp/vAlFzRRypxWWtbkPNBIItkImC6zn0IiGjBy50DE1io27W
hmQcnMb7d+0wWl2Y8OmR2lZSB97JiRZkRYMCVHVt+0zGJzp4prLvl9wbjh1VXkPv
ERCDJ9nCmZsl7ZVmIXMI7KNXYuPNp7R/QAzCvuSUueswF0qxTAQ0VSSBwRMqvQsQ
UUNC6p63VnjUeMUdn2EBsUQZ0Uqw3t2U5TtvooHNt9FkiGsSpwjWrvVD+LItaPoJ
GPeeJrJaYQsDvTrO8wjU
=ZtPK
-----END PGP SIGNATURE-----
Merge tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC platform support updates from Kevin Hilman:
"Our SoC branch usually contains expanded support for new SoCs and
other core platform code. Some highlights from this round:
- sunxi: SMP support for A23 SoC
- socpga: big-endian support
- pxa: conversion to common clock framework
- bcm: SMP support for BCM63138
- imx: support new I.MX7D SoC
- zte: basic support for ZX296702 SoC"
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (134 commits)
ARM: zx: Add basic defconfig support for ZX296702
ARM: dts: zx: add an initial zx296702 dts and doc
clk: zx: add clock support to zx296702
dt-bindings: Add #defines for ZTE ZX296702 clocks
ARM: socfpga: fix build error due to secondary_startup
MAINTAINERS: ARM64: EXYNOS: Extend entry for ARM64 DTS
ARM: ep93xx: simone: support for SPI-based MMC/SD cards
MAINTAINERS: update Shawn's email to use kernel.org one
ARM: socfpga: support suspend to ram
ARM: socfpga: add CPU_METHOD_OF_DECLARE for Arria 10
ARM: socfpga: use CPU_METHOD_OF_DECLARE for socfpga_cyclone5
ARM: EXYNOS: register power domain driver from core_initcall
ARM: EXYNOS: use PS_HOLD based poweroff for all supported SoCs
ARM: SAMSUNG: Constify platform_device_id
ARM: EXYNOS: Constify irq_domain_ops
ARM: EXYNOS: add coupled cpuidle support for Exynos3250
ARM: EXYNOS: add exynos_get_boot_addr() helper
ARM: EXYNOS: add exynos_set_boot_addr() helper
ARM: EXYNOS: make exynos_core_restart() less verbose
ARM: EXYNOS: fix exynos_boot_secondary() return value on timeout
...
A relatively small setup of cleanups this time around, and similar to last time
the bulk of it is removal of legacy board support:
- OMAP: removal of legacy (non-DT) booting for several platforms
- i.MX: remove some legacy board files
Conflicts: None
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=0zof
-----END PGP SIGNATURE-----
Merge tag 'armsoc-cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC cleanups from Kevin Hilman:
"A relatively small setup of cleanups this time around, and similar to
last time the bulk of it is removal of legacy board support:
- OMAP: removal of legacy (non-DT) booting for several platforms
- i.MX: remove some legacy board files"
* tag 'armsoc-cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (36 commits)
ARM: fix EFM32 build breakage caused by cpu_resume_arm
ARM: 8389/1: Add cpu_resume_arm() for firmwares that resume in ARM state
ARM: v7 setup function should invalidate L1 cache
mach-omap2: Remove use of deprecated marco, PTR_RET in devices.c
ARM: OMAP2+: Remove calls to deprecacted marco,PTR_RET in the files,fb.c and pmu.c
ARM: OMAP2+: Constify irq_domain_ops
ARM: OMAP2+: use symbolic defines for console loglevels instead of numbers
ARM: at91: remove useless Makefile.boot
ARM: at91: remove at91rm9200_sdramc.h
ARM: at91: remove mach/at91_ramc.h and mach/at91rm9200_mc.h
ARM: at91/pm: use the atmel-mc syscon defines
pcmcia: at91_cf: Use syscon to configure the MC/smc
ARM: at91: declare the at91rm9200 memory controller as a syscon
mfd: syscon: Add Atmel MC (Memory Controller) registers definition
ARM: at91: drop sam9_smc.c
ata: at91: use syscon to configure the smc
ARM: ux500: delete static resource defines
ARM: ux500: rename ux500_map_io
ARM: ux500: look up PRCMU resource from DT
ARM: ux500: kill off L2CC static map
...
Pull clkdev updates from Russell King:
"This series addresses some breakage in clkdev caused by a previous
patch set from the clk tree which introduced per-user clk structures.
This basically renamed the existing 'struct clk' to 'struct clk_hw',
and introduced a new 'struct clk'.
This change will break anyone using clk_add_alias() with the common
clk code enabled. Thankfully, the intersection of users of
clk_add_alias() and those using the common clk code is practically
zero, but this is something which should be fixed to keep the code
sane.
The problem is that clk_add_alias() does this:
r = clk_get(...);
l = clkdev_alloc(r, ...);
clk_put(...);
which causes the alias to store a pointer to 'r', which has been
freed.
The original patch set tried to work around this problem incorrectly -
at clk_get() time, it tried to convert the struct clk to a struct
clk_hw, and then creating a new struct clk from that. Clearly, if the
original struct clk has been freed, then we have a use-after-free bug.
We have other places in the tree which do something similar, so this
series also addresses those locations too.
This series addresses this problem by converting clkdev to store and
use the clk_hw pointer. This allows clk_get() to only have to create
it's per-user struct clk from the clk_hw. We can also get to the
desired clk_hw at clk_add_alias() or clk lookup creation time, when
the struct clk is "alive".
We also perform some cleanups of the code:
- replacing looped calls to clkdev_add() with clkdev_add_table()
- replacing open-coded lookup allocation (which should have been
using clkdev_alloc()) and subsequent clkdev_add() with
clkdev_create()
- replacing open-coded clk_add_alias() with clk_add_alias()"
* 'for-linus-clk' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
clk: s2mps11: use clkdev_create()
ASoC: migor: use clkdev_create()
ARM: omap2: use clkdev_add_alias()
ARM: omap2: use clkdev_create()
ARM: orion: use clkdev_create()
ARM: lpc32xx: convert to use clkdev_add_table()
SH: use clkdev_add_table()
clkdev: add clkdev_create() helper
clkdev: const-ify connection id to clk_add_alias()
clkdev: get rid of redundant clk_add_alias() prototype in linux/clk.h
clkdev: drop __init from clkdev_add_table()
clk: update clk API documentation to clarify clk_round_rate()
clkdev: use clk_hw internally
* pm-sleep:
PM / sleep: trace_device_pm_callback coverage in dpm_prepare/complete
PM / wakeup: add a dummy wakeup_source to record statistics
PM / sleep: Make suspend-to-idle-specific code depend on CONFIG_SUSPEND
PM / sleep: Return -EBUSY from suspend_enter() on wakeup detection
PM / tick: Add tracepoints for suspend-to-idle diagnostics
PM / sleep: Fix symbol name in a comment in kernel/power/main.c
leds / PM: fix hibernation on arm when gpio-led used with CPU led trigger
ARM: omap-device: use SET_NOIRQ_SYSTEM_SLEEP_PM_OPS
bus: omap_l3_noc: add missed callbacks for suspend-to-disk
PM / sleep: Add macro to define common noirq system PM callbacks
PM / sleep: Refine diagnostic messages in enter_state()
PM / wakeup: validate wakeup source before activating it.
* pm-runtime:
PM / Runtime: Update last_busy in rpm_resume
PM / runtime: add note about re-calling in during device probe()
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJVa7zvAAoJEHm+PkMAQRiGtfMIAILs3sxFtrC1hApgcfRLF/7z
K34bwTRqErzqUO/orTwakEr9kSIpIL0zIPSryTCOTPZLfMGkQjhHXO3KR/DSbbTV
MZ8y/BM/yelFA/Np+1LjbiYjTNRnTRvCoaQihkIH8Rn02g7ob9HyL4gIGKpuGFcZ
04GacL2cgChqsRSACdNef948jCoJXKgcuDpe39DXphDWZnBKNZ3HFuJ6bryGJf9A
1/eCI4is85BNwKPemQUYR0xx83UIzDfrghatZP2mOCDDSA2MNg8HNxLTd12LGoQD
tfgX4B7aftzW9Y7GSEDfZ0IKm2NRzgPmCVj6PjVR/iI0lIK4Aq0Z/lDJxxEq3XQ=
=AJM5
-----END PGP SIGNATURE-----
Merge tag 'v4.1-rc6' into next/dt
Linux 4.1-rc6
Conflicts:
arch/arm/boot/dts/zynq-7000.dtsi
Resolution summary:
Mainline had an earlier version of the commit, resolve in favor of the
newer patch in next/dt branch.
Simplify the DSS detection logic by creating a list of the omapdss
compat strings, instead of checking each separately with an 'if'.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Set DSS core hwmod as the parent for all the DSS submodules. This
ensures that the parent hwmods are enabled before any DSS submodules are
accessed.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
Add DMM hwmod entries for DRA7. This is identical to DMM on OMAP5.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
Add a new Linux clock for DRA7 based SoCs to control DESHDCP clock.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tero Kristo <t-kristo@ti.com>
With most of the clock code under clock driver already, the low-level
register access code, and the init code for the same, is no longer
needed outside the clock driver. Thus, these can be moved under clock
driver also.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
As most of the clock driver code has migrated, these are no longer used
for anything. Thus remove these APIs completely.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
We should avoid exporting data from drivers, instead use an API for
registering the clock low level operations.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
With legacy clock support gone, this is no longer needed under platform,
so move it under the clock driver itself. Make some exports be driver
internal definitions at the same time.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
With the legacy clock data gone, this is no longer needed under platform,
so move it under the clock driver itself. Remove unnecessary declarations
from the TI clock header also.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
With the legacy clock data gone, this is no longer needed under platform,
so move it under the clock driver itself. Remove the exported clock driver
APIs as well, as these are not needed outside clock driver anymore.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
With the legacy clock support gone, this is no longer needed under
platform code-base. Thus, move this under the TI clock driver, and
remove the exported API from the public header.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
With the legacy support gone, OMAP2+ default gate clock can be moved
under clock driver. Create a new file for the purpose, and clean-up
the header exports a bit as some clock APIs are no longer needed
outside clock driver itself.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
clkdm_control is used to determine, whether clocks should trigger a
clockdomain transition when they are enabled/disabled. Keep this
functionality intact, but replace this with a clk_features flag
which can be initialized during boot if needed.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
This now only has a couple of variables within it, which are used outside
the file itself. Move these variables to where they are actually used,
and remove the file completely as it is now empty.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
With the legacy clock support gone, OMAP3 generic DPLL code can now be
moved over to the clock driver also. A few un-unused clkoutx2 functions
are also removed at the same time.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Clock driver requires access to some CM API functions once the code
is being moved under the clock driver from the platform directory.
Gate type clock requires access to cm_wait_module_ready and
cm_split_idlest_reg functions, which are both used for waiting until
the module being clocked has been successfully activated. These CM
APIs are now exported through the ti_clk_ll_ops struct.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Clock driver requires access to certain clockdomain handling ops once
the code is being moved over under clock driver. Example of this is
clk_enable / clk_disable under omap3 DPLL code. The required clkdm
APIs are now exported through the ti_clk_ll_ops struct.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
The legacy support is wrong and dangerous, as it doesn't take any
OPPs into account and does not scale voltages. Switching mpurate should
be handled through cpufreq.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
This is no longer used outside clock driver, so move it under the driver
and remove the export for it from the global header file.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
This is no longer needed in platform directory, as the legacy clock data
is gone, so move it under TI clock driver. Some static functions are
renamed also.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
These files contain legacy clock implementations which are no longer used
for anything, thus remove them completely.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
This only contains clksel tables that were used with the legacy clock data.
Now that legacy clock data is completely gone, this file can be removed
also.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
The clksel clock type is no longer used for anything, it is rather
replaced with common clock divider code. Thus, remove the dead code
from kernel.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Core DVFS support code is currently referencing clksel functionality, which
is wrong. The m2 divisor has been implemented as a divider clock for a long
time already, so replace the validrate check call with proper functionality.
Core DVFS is currently not supported in the kernel so verifying this patch
can be rather tricky, this should probably be fixed at some point.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
With the legacy clock support gone, the OMAP interface clock implementation
can be moved under the clock driver. Some temporary header file tweaks are
also needed to make this change work properly.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
With the legacy clock support gone, the OMAP4 specific DPLL implementations
can be moved under the clock driver. Change some of the function prototypes
to be static at the same time, and remove some exports from the global TI
clock driver header.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
With the legacy clock data now gone, we can start moving OMAP clock
type implementations under clock driver. Start this with moving the
generic OMAP DPLL clock type under TI clock driver.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
As most of the clock driver support code is going to be moved under
drivers/clk/ti, an API for setting / getting the SoC specific clock
features is needed. This patch provides this API and changes the
existing code to use it.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Register crypto hwmod links only if they are not disabled in DT.
If DT information is missing, enable them only for GP devices.
Before this patch crypto hwmod links were always disabled for all HS
devices and it was not possible to use omap-aes and omap-sham linux
drivers.
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
[paul@pwsan.com: move the complex IP-block presence heuristics into their
own function to simplify the code; fix some checkpatch warnings]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Without this patch function pm_runtime_get_sync() returns 0 even when
some omap subfunction fails. This patch properly propagate error codes
from omap functions back to caller.
This patch fix problem, when loading omap-aes driver in qemu cause
kernel oops.
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
[paul@pwsan.com: fix a checkpatch warning]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Without a hwmod for am43xx emif use counting for emif clockdomain does
not happen correctly so it may be shut off by pm code unintentionally.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
[paul@pwsan.com: updated to apply]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
We support decoding the bootloader values if DEBUG is defined.
But we also need to change the struct omap_hwmod flags to have
HWMOD_INIT_NO_RESET to avoid the GPMC being reset during the
boot. Otherwise just the default timings will be displayed
instead of the bootloader configured timings.
This also allows us to clean up the various GPMC related
hwmod flags. For debugging, we only need HWMOD_INIT_NO_RESET,
and HWMOD_INIT_NO_IDLE is not needed.
Cc: Brian Hutchinson <b.hutchman@gmail.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
This removes the no longer required return statement at the end
of the void function, omap2_show_dma_cap due to no need for a
return statement due to this function always running successfully.
Signed-off-by: Nicholas Krause <xerofoify@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Merge cleanups from Russell King:
* 'for-arm-soc' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
ARM: Show proper respect for Heinrich Hertz by using the correct unit for frequency
- Configure MMC data lines 4..8 for 1.8V IO on boards that
are using them as GPIOs instead of MMC data lines
- Add support for Baltos IR5221
- Add device tree support for LogicPD Torpedo devkit
- Add 3717 core pinctrl region
- Add gta04 1w and GSM audio support
- Add wilink and ov2659 support for am437x-gp-evm
- Add am335x-evm bluetooth and mmc3 support
- Enable omap5-uevm uart wakeup interrupt
- Enable I2C2 on BeagleBone as it's used for the capes
- Use defines for LDP GPIO keys
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=MmxV
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.2/dt-pt1' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/dt
Merge "Device tree related changes for omaps" from Tony Lindgren:
- Configure MMC data lines 4..8 for 1.8V IO on boards that
are using them as GPIOs instead of MMC data lines
- Add support for Baltos IR5221
- Add device tree support for LogicPD Torpedo devkit
- Add 3717 core pinctrl region
- Add gta04 1w and GSM audio support
- Add wilink and ov2659 support for am437x-gp-evm
- Add am335x-evm bluetooth and mmc3 support
- Enable omap5-uevm uart wakeup interrupt
- Enable I2C2 on BeagleBone as it's used for the capes
- Use defines for LDP GPIO keys
* tag 'omap-for-v4.2/dt-pt1' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: am335x-evm: add mmc3 and wlan definitions to dts
ARM: dts: Enable SDIO card interrupt for 37xx-evm
ARM: dts: Fix ldp gpio keys to use defines
ARM: dts: Beaglebone i2c definitions
ARM: dts: am437x-gp-evm: add DT nodes for ov2659 sensor
ARM: dts: add DTS for Baltos IR5221
ARM: dts: omap5-uevm: Add Uart wakeup interrupt
ARM: dts: omap3-gta04: Add GSM audio support
ARM: dts: am335x-evm: add bluetooth support
ARM: dts: am437x-gp-evm: add wilink8 support
ARM: dts: omap3-gta04: Add hdqw1 support
ARM: dts: add core2 padconf region for am3517
ARM: dts: Add minimal support for LogicPD Torpedo DM3730 devkit
ARM: OMAP3: Add support for configuring MMC pins as GPIO pins
We get a NULL pointer dereference on omap3 for thumb2 compiled kernels:
Internal error: Oops: 80000005 [#1] SMP THUMB2
...
[<c046497b>] (_raw_spin_unlock_irqrestore) from [<c0024375>]
(omap3_enter_idle_bm+0xc5/0x178)
[<c0024375>] (omap3_enter_idle_bm) from [<c0374e63>]
(cpuidle_enter_state+0x77/0x27c)
[<c0374e63>] (cpuidle_enter_state) from [<c00627f1>]
(cpu_startup_entry+0x155/0x23c)
[<c00627f1>] (cpu_startup_entry) from [<c06b9a47>]
(start_kernel+0x32f/0x338)
[<c06b9a47>] (start_kernel) from [<8000807f>] (0x8000807f)
The power management related assembly on omaps needs to interact with
ARM mode bootrom code, so we need to keep most of the related assembly
in ARM mode.
Turns out this error is because of missing ENDPROC for assembly code
as suggested by Stephen Boyd <sboyd@codeaurora.org>. Let's fix the
problem by adding ENDPROC in two places to sleep34xx.S.
Let's also remove the now duplicate custom code for mode switching.
This has been unnecessary since commit 6ebbf2ce43 ("ARM: convert
all "mov.* pc, reg" to "bx reg" for ARMv6+").
And let's also remove the comments about local variables, they are
now just confusing after the ENDPROC.
The reason why ENDPROC makes a difference is it sets .type and then
the compiler knows what to do with the thumb bit as explained at:
https://wiki.ubuntu.com/ARM/Thumb2PortingHowto
Reported-by: Kevin Hilman <khilman@kernel.org>
Tested-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Drop more omap3 legacy board-*.c files for v4.2. This time we're
dropping the board files for beagle, overo and cm-t35.
The reason for dropping these now rather than later is that now
we can simply revert the patches in case of unexpected issues as
we are not dropping any platform data at this point.
This leaves us with only the following board-*.c files:
BOARD REASON NEEDED
board-ldp.c Still used in RMKs boot test system
board-omap3logic.c Getting a .dts file for v4.2
board-omap3pandora.c Got a .dts file for v4.1
board-rx51-*.c Needs /proc/atags support for user space
I'm hoping we can drop the remaining board-*.c for v4.3 merge
window, then keep the platform data around for one more merge
window in case of reverting needed, then drop the platform data
too for v4.4 if no issues needing reverting are found.
Also, few patches to clean-up the usage of Linux generic
macros:
- Use define for console loglevel
- Use const for struct irq_domain_ops
- Use PTR_ERR_OR_ZERO instead of PTR_RET
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=AVB2
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.2/clean' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/cleanup
Merge "Clean-up for omaps for v4.2 merge window" from Tony Lindgren:
Drop more omap3 legacy board-*.c files for v4.2. This time we're
dropping the board files for beagle, overo and cm-t35.
The reason for dropping these now rather than later is that now
we can simply revert the patches in case of unexpected issues as
we are not dropping any platform data at this point.
This leaves us with only the following board-*.c files:
BOARD REASON NEEDED
board-ldp.c Still used in RMKs boot test system
board-omap3logic.c Getting a .dts file for v4.2
board-omap3pandora.c Got a .dts file for v4.1
board-rx51-*.c Needs /proc/atags support for user space
I'm hoping we can drop the remaining board-*.c for v4.3 merge
window, then keep the platform data around for one more merge
window in case of reverting needed, then drop the platform data
too for v4.4 if no issues needing reverting are found.
Also, few patches to clean-up the usage of Linux generic
macros:
- Use define for console loglevel
- Use const for struct irq_domain_ops
- Use PTR_ERR_OR_ZERO instead of PTR_RET
* tag 'omap-for-v4.2/clean' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
mach-omap2: Remove use of deprecated marco, PTR_RET in devices.c
ARM: OMAP2+: Remove calls to deprecacted marco,PTR_RET in the files,fb.c and pmu.c
ARM: OMAP2+: Constify irq_domain_ops
ARM: OMAP2+: use symbolic defines for console loglevels instead of numbers
ARM: OMAP2+: Remove legacy booting support for Beagleboards
ARM: OMAP2+: Remove legacy booting support for Overo
ARM: OMAP2+: Remove legacy booting support for cm-t35
This removes the deprecacted marco, PTR_RET and changes the
functions that use this marco in their return statement to
instead use the non deprecacted function, PTR_ERR_OR_ZERO
for the file devices.c.
Signed-off-by: Nicholas Krause <xerofoify@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This removes two calls to the deprecated marco,PTR_RET in
the files,fb.c and pmu.c for the functions,omap_init_vrfb
and omap_init_pmu respectfully. Furthermore these are now
replaced by calling the correctly non deprecacted function,
PTR_ERR_OR_ZERO in both functions.
Signed-off-by: Nicholas Krause <xerofoify@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The irq_domain_ops are not modified by the driver and the irqdomain core
code accepts pointer to a const data.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
<linux/printk.h> provides macros for console log level, let's use it
instead of numbers.
Signed-off-by: Alexander Kuleshov <kuleshovmail@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Some devices are using the MMC1 pins 4..8 as GPIO pins, and in
this case they need to be configured for 1.8V IO voltage if not
done by the bootloader as otherwise some devices like smsc911x
won't work properly.
Let's also make sure this register is saved and restored for
idle.
Cc: Tim Nordell <tim.nordell@logicpd.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The SI unit of frequency is Hertz, named after Heinrich Hertz, and is
given the symbol "Hz" to denote this. "hz" is not the unit of frequency,
and is in fact meaningless.
Fix arch/arm to correctly use "Hz", thereby acknowledging Heinrich Hertz'
contribution to the modern world.
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Reviewed-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Use recently introduced macro SET_NOIRQ_SYSTEM_SLEEP_PM_OPS to
set up PM callbacks. This also fixes missed assignment of
.poweroff_noirq() callback.
Signed-off-by: Grygorii Strashko <Grygorii.Strashko@linaro.org>
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Pavel Machek <pavel@ucw.cz>
Reviewed-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Fix a few AM43xx problems: add the VPFE hwmod data, which removes some
warnings; and fix the IP block hardreset implementation.
Basic build, boot, and PM test results are here:
http://www.pwsan.com/omap/testlogs/omap-hwmod-a-for-v4.1-rc/20150508130543/
Note that I do not have an AM43xx board in the testbed, and thus
cannot test on that platform.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=jonz
-----END PGP SIGNATURE-----
Merge tag 'for-v4.1-rc/omap-fixes-a' of git://git.kernel.org/pub/scm/linux/kernel/git/pjw/omap-pending into omap-for-v4.1/fixes
ARM: OMAP2+: first set of hwmod fixes for v4.1-rc
Fix a few AM43xx problems: add the VPFE hwmod data, which removes some
warnings; and fix the IP block hardreset implementation.
Basic build, boot, and PM test results are here:
http://www.pwsan.com/omap/testlogs/omap-hwmod-a-for-v4.1-rc/20150508130543/
Note that I do not have an AM43xx board in the testbed, and thus
cannot test on that platform.
With recent changes to use determine_rate, the comparison of two
clocks won't work without clk_is_match that does __clk_get_hw
on the clocks first.
As we've been unconditionally already calling clk_set_parent
already because of the bogus comparison, let's just remove the
check as suggested by Stephen Boyd <sboyd@codeaurora.org>.
Cc: Michael Turquette <mturquette@linaro.org>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Tero Kristo <t-kristo@ti.com>
Cc: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The reset code functionality is mostly a copy paste between OMAP4+ and
AM33xx+. Re-use the omap4 code where possible, and just keep the special
implementation for de-asserting the hardreset lines for AM33xx, as
AM33xx+ devices have slightly different register layouts compared to
OMAP4+. This patch also fixes the hardreset issues faced on AM43xx.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Reported-by: Dave Gerlach <d-gerlach@ti.com>
Reported-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
AM43xx has slightly different reset register layout compared to OMAP4+,
with varying status bit shifts and status register offsets. Current
code assumes static offsets and identical status / reset control bit
shifts, which is wrong. This patch adds PRM core support for passing
the actual implementations from hwmod code. AM43xx mappings will be fixed
in subsequent patch.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Reported-by: Dave Gerlach <d-gerlach@ti.com>
Reported-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
This patch adds VPFE HWMOD data for AM43xx.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Darren Etheridge <detheridge@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Tested-by: Benoit Parrot <bparrot@ti.com>
[paul@pwsan.com: updated to apply on v4.1-rc1]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
We've been moving all omap2+ based systems to boot in device tree only
mode for a few years now. Only omap3 has legacy booting support
remaining. Most omap3 boards already have related arch/arm/boot/*.dts*
files for booting with device tree.
This board has support for device tree based booting, and we've been
printing warnings about the legacy booting being deprecated for a
few merge cycles now. Let's attempt to remove the legacy booting
for it.
The reason for removing the legacy booting support now rather than
later is we can simply revert this patch if necessary if we run
into some unexpected issues that are not trivial to fix for the
device tree based booting.
Signed-off-by: Tony Lindgren <tony@atomide.com>
When creating aliases of existing clkdev clocks, use clkdev_add_alias()
isntead of open coding the lookup and clk_lookup creation.
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Rather than open coding the clkdev allocation, initialisation and
addition, use the clkdev_create() helper.
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
We've been moving all omap2+ based systems to boot in device tree only
mode for a few years now. Only omap3 has legacy booting support
remaining. Most omap3 boards already have related arch/arm/boot/*.dts*
files for booting with device tree.
This board has support for device tree based booting, and we've been
printing warnings about the legacy booting being deprecated for a
few merge cycles now. Let's attempt to remove the legacy booting
for it.
The reason for removing the legacy booting support now rather than
later is we can simply revert this patch if necessary if we run
into some unexpected issues that are not trivial to fix for the
device tree based booting.
Cc: Florian Vaussard <florian.vaussard@epfl.ch>
Acked-by: Ash Charles <ashcharles@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We've been moving all omap2+ based systems to boot in device tree only
mode for a few years now. Only omap3 has legacy booting support
remaining. Most omap3 boards already have related arch/arm/boot/*.dts*
files for booting with device tree.
This board has support for device tree based booting, and we've been
printing warnings about the legacy booting being deprecated for a
few merge cycles now. Let's attempt to remove the legacy booting
for it.
The reason for removing the legacy booting support now rather than
later is we can simply revert this patch if necessary if we run
into some unexpected issues that are not trivial to fix for the
device tree based booting.
Cc: Dmitry Lifshitz <lifshitz@compulab.co.il>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
If we use a combination of VMODE and I2C4 for retention modes,
eventually the off idle power consumption will creep up by about
23mW, even during off mode with I2C4 always staying enabled.
Turns out this is because of erratum i531 "Extra Power Consumed
When Repeated Start Operation Mode Is Enabled on I2C Interface
Dedicated for Smart Reflex (I2C4)" as pointed out by Nishanth
Menon <nm@ti.com>.
Let's fix the issue by adding i2c_cfg_clear_mask for the bits
to clear when initializing the I2C4 adapter so we can clear
SREN bit that drives the I2C4 lines low otherwise when there
is no traffic.
Fixes: 3b8c4ebb76 ("ARM: OMAP3: Fix idle mode signaling for
Cc: stable@vger.kernel.org # v3.16+
sys_clkreq and sys_off_mode")
Cc: Kevin Hilman <khilman@kernel.org>
Cc: Tero Kristo <t-kristo@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
HwSpinlock IP is present only on OMAP4 and other newer SoCs,
which are all device-tree boot only. This patch adds the
base support for parsing the DT nodes, and removes the code
dealing with the traditional platform device instantiation.
Signed-off-by: Suman Anna <s-anna@ti.com>
[tony@atomide.com: ack for legacy file removal]
Acked-by: Tony Lindgren <tony@atomide.com>
[comment on the imperfect always-zero base_id]
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
We were expecting to sit on this branch through most of the merge window since
the contents was merged into our tree late, but we ended up sitting on all of
our contents so it can go in with the rest.
The contents here is:
- A large branch of cleanups of the CM/PRM blocks on OMAP.
- A couple of patches plumbing up CM/PRM on OMAP5 and DRA7.
- A branch with DT updates for Freescale i.MX. including some shuffling from
.dts to .dtsi (include) files that causes a little churn.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=ssbK
-----END PGP SIGNATURE-----
Merge tag 'armsoc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC late changes from Olof Johansson:
"We were expecting to sit on this branch through most of the merge
window since the contents was merged into our tree late, but we ended
up sitting on all of our contents so it can go in with the rest.
The contents here is:
- a large branch of cleanups of the CM/PRM blocks on OMAP.
- a couple of patches plumbing up CM/PRM on OMAP5 and DRA7.
- a branch with DT updates for Freescale i.MX. including some
shuffling from .dts to .dtsi (include) files that causes a little
churn"
* tag 'armsoc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (78 commits)
ARM: OMAP2+: Fix booting with configs that don't have MFD_SYSCON
ARM: OMAP4+: control: add support for initializing control module via DT
ARM: dts: dra7: add minimal l4 bus layout with control module support
ARM: dts: omap5: add minimal l4 bus layout with control module support
ARM: OMAP4+: control: remove support for legacy pad read/write
ARM: OMAP4: display: convert display to use syscon for dsi muxing
ARM: dts: omap4: add minimal l4 bus layout with control module support
ARM: dts: am4372: add minimal l4 bus layout with control module support
ARM: dts: am43xx-epos-evm: fix pinmux node layout
ARM: dts: am33xx: add minimal l4 bus layout with control module support
ARM: dts: omap3: add minimal l4 bus layout with control module support
ARM: dts: omap24xx: add minimal l4 bus layout with control module support
ARM: OMAP2+: control: add syscon support for register accesses
ARM: OMAP2+: id: cache omap_type value
ARM: OMAP2+: control: remove API for getting control module base address
ARM: OMAP2+: clock: add low-level support for regmap
ARM: OMAP4+: PRM: get rid of cpu_is_omap44xx calls from interrupt init
ARM: OMAP4+: PRM: setup prm_features from the PRM init time flags
ARM: OMAP2+: CM: move SoC specific init calls within a generic API
ARM: OMAP4+: PRM: determine prm_device_inst based on DT compatibility
...
Driver updates for v4.1. Some of these are for drivers/soc, where we find more
and more SoC-specific drivers these days. Some are for other driver subsystems
where we have received acks from the appropriate maintainers.
The larger parts of this branch are:
- MediaTek support for their PMIC wrapper interface, a high-level interface
for talking to the system PMIC over a dedicated I2C interface.
- Qualcomm SCM driver has been moved to drivers/firmware. It's used for CPU
up/down and needs to be in a shared location for arm/arm64 common code.
- Cleanup of ARM-CCI PMU code.
- Anoter set of cleanusp to the OMAP GPMC code.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=/sWo
-----END PGP SIGNATURE-----
Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver updates from Olof Johansson:
"Driver updates for v4.1. Some of these are for drivers/soc, where we
find more and more SoC-specific drivers these days. Some are for
other driver subsystems where we have received acks from the
appropriate maintainers.
The larger parts of this branch are:
- MediaTek support for their PMIC wrapper interface, a high-level
interface for talking to the system PMIC over a dedicated I2C
interface.
- Qualcomm SCM driver has been moved to drivers/firmware. It's used
for CPU up/down and needs to be in a shared location for arm/arm64
common code.
- cleanup of ARM-CCI PMU code.
- another set of cleanusp to the OMAP GPMC code"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (43 commits)
soc/mediatek: Remove unused variables
clocksource: atmel-st: select MFD_SYSCON
soc: mediatek: Add PMIC wrapper for MT8135 and MT8173 SoCs
arm-cci: Fix CCI PMU event validation
arm-cci: Split the code for PMU vs driver support
arm-cci: Get rid of secure transactions for PMU driver
arm-cci: Abstract the CCI400 PMU specific definitions
arm-cci: Rearrange code for splitting PMU vs driver code
drivers: cci: reject groups spanning multiple HW PMUs
ARM: at91: remove useless include
clocksource: atmel-st: remove mach/hardware dependency
clocksource: atmel-st: use syscon/regmap
ARM: at91: time: move the system timer driver to drivers/clocksource
ARM: at91: properly initialize timer
ARM: at91: at91rm9200: remove deprecated arm_pm_restart
watchdog: at91rm9200: implement restart handler
watchdog: at91rm9200: use the system timer syscon
mfd: syscon: Add atmel system timer registers definition
ARM: at91/dt: declare atmel,at91rm9200-st as a syscon
soc: qcom: gsbi: Add support for ADM CRCI muxing
...
As always, this tends to be one of our bigger branches. There are lots of
updates this release, but not that many jumps out as something that needs
more detailed coverage. Some of the highlights are:
- DTs for the new Annapurna Labs Alpine platform
- More graphics DT pieces falling into place on Exynos, bridges, clocks.
- Plenty of DT updates for Qualcomm platforms for various IP blocks
- Some churn on Tegra due to switch-over to tool-generated pinctrl data
- Misc fixes and updates for Atmel at91 platforms
- Various DT updates to add IP block support on Broadcom's Cygnus platforms
- More updates for Renesas platforms as DT support is added for various IP
blocks (IPMMU, display, audio, etc).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=wqhB
-----END PGP SIGNATURE-----
Merge tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM DT updates from Olof Johansson:
"As always, this tends to be one of our bigger branches. There are
lots of updates this release, but not that many jumps out as something
that needs more detailed coverage. Some of the highlights are:
- DTs for the new Annapurna Labs Alpine platform
- more graphics DT pieces falling into place on Exynos, bridges,
clocks.
- plenty of DT updates for Qualcomm platforms for various IP blocks
- some churn on Tegra due to switch-over to tool-generated pinctrl
data
- misc fixes and updates for Atmel at91 platforms
- various DT updates to add IP block support on Broadcom's Cygnus
platforms
- more updates for Renesas platforms as DT support is added for
various IP blocks (IPMMU, display, audio, etc)"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (231 commits)
ARM: dts: alpine: add internal pci
Revert "ARM: dts: mt8135: Add pinctrl/GPIO/EINT node for mt8135."
ARM: mvebu: use 0xf1000000 as internal registers on Armada 370 DB
ARM: dts: qcom: Add idle state device nodes for 8064
ARM: dts: qcom: Add idle states device nodes for 8084
ARM: dts: qcom: Add idle states device nodes for 8974/8074
ARM: dts: qcom: Update power-controller device node for 8064 Krait CPUs
ARM: dts: qcom: Add power-controller device node for 8084 Krait CPUs
ARM: dts: qcom: Add power-controller device node for 8074 Krait CPUs
devicetree: bindings: Document qcom,idle-states
devicetree: bindings: Update qcom,saw2 node bindings
dt-bindings: Add #defines for MSM8916 clocks and resets
arm: dts: qcom: Add LPASS Audio HW to IPQ8064 device tree
arm: dts: qcom: Add APQ8084 chipset SPMI PMIC's nodes
arm: dts: qcom: Add 8x74 chipset SPMI PMIC's nodes
arm: dts: qcom: Add SPMI PMIC Arbiter nodes for APQ8084 and MSM8974
arm: dts: qcom: Add LCC nodes
arm: dts: qcom: Add TCSR support for MSM8960
arm: dts: qcom: Add TCSR support for MSM8660
arm: dts: qcom: Add TCSR support for IPQ8064
...
Our SoC branch usually contains expanded support for new SoCs and other core
platform code. In this case, that includes:
- Support for the new Annapurna Labs "Alpine" platform
- A rework greatly simplifying adding new platform support to the MCPM
subsystem (Multi-cluster power management)
- Cpuidle and PM improvements for Exynos3250
- Misc updates for Renesas, OMAP, Meson, i.MX. Some of these could have
gone in other branches but ended up here for various reasons.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=tcGs
-----END PGP SIGNATURE-----
Merge tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC platform updates from Olof Johansson:
"Our SoC branch usually contains expanded support for new SoCs and
other core platform code. In this case, that includes:
- support for the new Annapurna Labs "Alpine" platform
- a rework greatly simplifying adding new platform support to the
MCPM subsystem (Multi-cluster power management)
- cpuidle and PM improvements for Exynos3250
- misc updates for Renesas, OMAP, Meson, i.MX. Some of these could
have gone in other branches but ended up here for various reasons"
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (53 commits)
ARM: alpine: add support for generic pci
ARM: Exynos: migrate DCSCB to the new MCPM backend abstraction
ARM: vexpress: migrate DCSCB to the new MCPM backend abstraction
ARM: vexpress: DCSCB: tighten CPU validity assertion
ARM: vexpress: migrate TC2 to the new MCPM backend abstraction
ARM: MCPM: move the algorithmic complexity to the core code
ARM: EXYNOS: allow cpuidle driver usage on Exynos3250 SoC
ARM: EXYNOS: add AFTR mode support for Exynos3250
ARM: EXYNOS: add code for setting/clearing boot flag
ARM: EXYNOS: fix CPU1 hotplug on Exynos3250
ARM: S3C64XX: Use fixed IRQ bases to avoid conflicts on Cragganmore
ARM: cygnus: fix const declaration bcm_cygnus_dt_compat
ARM: DRA7: hwmod: Fix the hwmod class for GPTimer4
ARM: DRA7: hwmod: Add data for GPTimers 13 through 16
ARM: EXYNOS: Remove left over 'extra_save'
ARM: EXYNOS: Constify exynos_pm_data array
ARM: EXYNOS: use static in suspend.c
ARM: EXYNOS: Use platform device name as power domain name
ARM: EXYNOS: add support for async-bridge clocks for pm_domains
ARM: omap-device: add missed callback for suspend-to-disk
...
We've got a fairly large cleanup branch this time. The bulk of this is removal
of non-DT platforms of several flavors:
- Atmel at91 platforms go full-DT, with removal of remaining board-file based
support
- OMAP removes legacy board files for three more platforms
- Removal of non-DT mach-msm, newer Qualcomm platforms now live in mach-qcom
- Freescale i.MX25 also removes non-DT platform support
Most of the rest of the changes here are fallout from the above, i.e. for
example removal of drivers that now lack platforms, etc.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=BV8A
-----END PGP SIGNATURE-----
Merge tag 'armsoc-cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC cleanups from Olof Johansson:
"We've got a fairly large cleanup branch this time. The bulk of this
is removal of non-DT platforms of several flavors:
- Atmel at91 platforms go full-DT, with removal of remaining
board-file based support
- OMAP removes legacy board files for three more platforms
- removal of non-DT mach-msm, newer Qualcomm platforms now live in
mach-qcom
- Freescale i.MX25 also removes non-DT platform support"
Most of the rest of the changes here are fallout from the above, i.e. for
example removal of drivers that now lack platforms, etc.
* tag 'armsoc-cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (58 commits)
mmc: Remove msm_sdcc driver
gpio: Remove gpio-msm-v1 driver
ARM: Remove mach-msm and associated ARM architecture code
ARM: shmobile: cpuidle: Remove the pointless default driver
ARM: davinci: dm646x: Add interrupt resource for McASPs
ARM: davinci: irqs: Correct McASP1 TX interrupt definition for DM646x
ARM: davinci: dm646x: Clean up the McASP DMA resources
ARM: davinci: devices-da8xx: Add support for McASP2 on da830
ARM: davinci: devices-da8xx: Clean up and correct the McASP device creation
ARM: davinci: devices-da8xx: Add interrupt resource to McASP structs
ARM: davinci: devices-da8xx: Add resource name for the McASP DMA request
ARM: OMAP2+: Remove legacy support for omap3 TouchBook
ARM: OMAP3: Remove legacy support for devkit8000
ARM: OMAP3: Remove legacy support for EMA-Tech Stalker board
ARM: shmobile: Consolidate the pm code for R-Car Gen2
ARM: shmobile: r8a7791: Correct SYSCIER value
ARM: shmobile: r8a7790: Correct SYSCIER value
ARM: at91: remove old setup
ARM: at91: sama5d4: remove useless map_io
ARM: at91: sama5 use SoC detection infrastructure
...
Here's the usual "low-priority fixes that didn't make it into the last
few -rcs, with a twist: We had a fixes pull request that I didn't send
in time to get into 4.0, so we'll send some of them to Greg for -stable as
well.
Contents here is as usual not all that controversial:
- A handful of randconfig fixes from Arnd, in particular for older Samsung
platforms
- Exynos fixes, !SMP building, DTS updates for MMC and lid switch
- Kbuild fix to create output subdirectory for DTB files
- Misc minor fixes for OMAP
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=o/4N
-----END PGP SIGNATURE-----
Merge tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"Here's the usual "low-priority fixes that didn't make it into the last
few -rcs, with a twist: We had a fixes pull request that I didn't send
in time to get into 4.0, so we'll send some of them to Greg for
-stable as well.
Contents here is as usual not all that controversial:
- a handful of randconfig fixes from Arnd, in particular for older
Samsung platforms
- Exynos fixes, !SMP building, DTS updates for MMC and lid switch
- Kbuild fix to create output subdirectory for DTB files
- misc minor fixes for OMAP"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (23 commits)
ARM: at91/dt: sama5d3 xplained: add phy address for macb1
kbuild: Create directory for target DTB
ARM: mvebu: Disable CPU Idle on Armada 38x
ARM: DRA7: Enable Cortex A15 errata 798181
ARM: dts: am57xx-beagle-x15: Add thermal map to include fan and tmp102
ARM: dts: DRA7: Add bandgap and related thermal nodes
bus: ocp2scp: SYNC2 value should be changed to 0x6
ARM: dts: am4372: Add "ti,am437x-ocp2scp" as compatible string for OCP2SCP
ARM: OMAP2+: remove superfluous NULL pointer check
ARM: EXYNOS: Fix build breakage cpuidle on !SMP
ARM: dts: fix lid and power pin-functions for exynos5250-spring
ARM: dts: fix mmc node updates for exynos5250-spring
ARM: OMAP4: remove dead kconfig option OMAP4_ERRATA_I688
MAINTAINERS: add OMAP defconfigs under OMAP SUPPORT
ARM: OMAP1: PM: fix some build warnings on 1510-only Kconfigs
ARM: cns3xxx: don't export static symbol
ARM: S3C24XX: avoid a Kconfig warning
ARM: S3C24XX: fix header file inclusions
ARM: S3C24XX: fix building without PM_SLEEP
ARM: S3C24XX: use SAMSUNG_WAKEMASK for s3c2416
...
.config files that do not have MFD_SYSCON set.
Omaps now have a dependency to MFD_SYSCON for system control
module generic register area and some clocks with the changes
done in omap-for-v4.1/prcm-dts branch.
This can be pulled on top of omap-for-v4.1/prcm-dts, or into
fixes for v4.1.
We already do have a slight MFD_SYSCON dependency for
REGULATOR_PBIAS for dual voltage MMC cards on the first MMC
bus for many devices, so from that point of view this can
also be merged separately from omap-for-v4.1/prcm-dts.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=4WLp
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.1/prcm-dts-mfd-syscon-fix' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/late
Merge "urgent omap boot fix for v4.1 if MFD_SYSCON is not set" from Tony
Lindgren:
Urgent pull request for v4.1 to booting for custom kernel
.config files that do not have MFD_SYSCON set.
Omaps now have a dependency to MFD_SYSCON for system control
module generic register area and some clocks with the changes
done in omap-for-v4.1/prcm-dts branch.
This can be pulled on top of omap-for-v4.1/prcm-dts, or into
fixes for v4.1.
We already do have a slight MFD_SYSCON dependency for
REGULATOR_PBIAS for dual voltage MMC cards on the first MMC
bus for many devices, so from that point of view this can
also be merged separately from omap-for-v4.1/prcm-dts.
* tag 'omap-for-v4.1/prcm-dts-mfd-syscon-fix' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: Fix booting with configs that don't have MFD_SYSCON
Signed-off-by: Olof Johansson <olof@lixom.net>
* 'drm-next-merged' of git://people.freedesktop.org/~airlied/linux: (9717 commits)
media-bus: Fixup RGB444_1X12, RGB565_1X16, and YUV8_1X24 media bus format
hexdump: avoid warning in test function
fs: take i_mutex during prepare_binprm for set[ug]id executables
smp: Fix error case handling in smp_call_function_*()
iommu-common: Fix PARISC compile-time warnings
sparc: Make LDC use common iommu poll management functions
sparc: Make sparc64 use scalable lib/iommu-common.c functions
Break up monolithic iommu table/lock into finer graularity pools and lock
sparc: Revert generic IOMMU allocator.
tools/power turbostat: correct dumped pkg-cstate-limit value
tools/power turbostat: calculate TSC frequency from CPUID(0x15) on SKL
tools/power turbostat: correct DRAM RAPL units on recent Xeon processors
tools/power turbostat: Initial Skylake support
tools/power turbostat: Use $(CURDIR) instead of $(PWD) and add support for O= option in Makefile
tools/power turbostat: modprobe msr, if needed
tools/power turbostat: dump MSR_TURBO_RATIO_LIMIT2
tools/power turbostat: use new MSR_TURBO_RATIO_LIMIT names
Bluetooth: hidp: Fix regression with older userspace and flags validation
config: Enable NEED_DMA_MAP_STATE by default when SWIOTLB is selected
perf/x86/intel/pt: Fix and clean up error handling in pt_event_add()
...
That solves several merge conflicts:
Documentation/DocBook/media/v4l/subdev-formats.xml
Documentation/devicetree/bindings/vendor-prefixes.txt
drivers/staging/media/mn88473/mn88473.c
include/linux/kconfig.h
include/uapi/linux/media-bus-format.h
The ones at subdev-formats.xml and media-bus-format.h are not trivial.
That's why we opted to merge from DRM.
With the recent changes omaps have developed a dependency to MFD_SYSCON.
This is used for system control module generic register area and some
clocks.
We do have it selected in omap2plus_defconfig, but targeted config
files may not have it selected. Let's make sure it's selected like
few other ARM platforms are already doing.
Reported-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Merge a set of fixes that we missed sending in before v4.0 release. These
will also be sent to -stable.
* fixes: (659 commits)
ARM: at91/dt: sama5d3 xplained: add phy address for macb1
kbuild: Create directory for target DTB
ARM: mvebu: Disable CPU Idle on Armada 38x
arm64: juno: Fix misleading name of UART reference clock
ARM: dts: sunxi: Remove overclocked/overvoltaged OPP
ARM: dts: sun4i: a10-lime: Override and remove 1008MHz OPP setting
ARM: socfpga: dts: fix spi1 interrupt
ARM: dts: Fix gpio interrupts for dm816x
ARM: dts: dra7: remove ti,hwmod property from pcie phy
ARM: EXYNOS: Fix build breakage cpuidle on !SMP
ARM: OMAP: dmtimer: disable pm runtime on remove
ARM: OMAP: dmtimer: check for pm_runtime_get_sync() failure
ARM: dts: fix lid and power pin-functions for exynos5250-spring
ARM: dts: fix mmc node updates for exynos5250-spring
ARM: OMAP2+: Fix socbus family info for AM33xx devices
ARM: dts: omap3: Add missing dmas for crypto
+ Linux 4.0-rc4
Signed-off-by: Olof Johansson <olof@lixom.net>
- Generic PM domains support update including new PM domain
callbacks to handle device initialization better (Russell King,
Rafael J Wysocki, Kevin Hilman).
- Unified device properties API update including a new mechanism
for accessing data provided by platform initialization code
(Rafael J Wysocki, Adrian Hunter).
- ARM cpuidle update including ARM32/ARM64 handling consolidation
(Daniel Lezcano).
- intel_idle update including support for the Silvermont Core in
the Baytrail SOC and for the Airmont Core in the Cherrytrail and
Braswell SOCs (Len Brown, Mathias Krause).
- New cpufreq driver for Hisilicon ACPU (Leo Yan).
- intel_pstate update including support for the Knights Landing
chip (Dasaratharaman Chandramouli, Kristen Carlson Accardi).
- QorIQ cpufreq driver update (Tang Yuantian, Arnd Bergmann).
- powernv cpufreq driver update (Shilpasri G Bhat).
- devfreq update including Tegra support changes (Tomeu Vizoso,
MyungJoo Ham, Chanwoo Choi).
- powercap RAPL (Running-Average Power Limit) driver update
including support for Intel Broadwell server chips (Jacob Pan,
Mathias Krause).
- ACPI device enumeration update related to the handling of the
special PRP0001 device ID allowing DT-style 'compatible' property
to be used for ACPI device identification (Rafael J Wysocki).
- ACPI EC driver update including limited _DEP support (Lan Tianyu,
Lv Zheng).
- ACPI backlight driver update including a new mechanism to allow
native backlight handling to be forced on non-Windows 8 systems
and a new quirk for Lenovo Ideapad Z570 (Aaron Lu, Hans de Goede).
- New Windows Vista compatibility quirk for Sony VGN-SR19XN (Chen Yu).
- Assorted ACPI fixes and cleanups (Aaron Lu, Martin Kepplinger,
Masanari Iida, Mika Westerberg, Nan Li, Rafael J Wysocki).
- Fixes related to suspend-to-idle for the iTCO watchdog driver and
the ACPI core system suspend/resume code (Rafael J Wysocki, Chen Yu).
- PM tracing support for the suspend phase of system suspend/resume
transitions (Zhonghui Fu).
- Configurable delay for the system suspend/resume testing facility
(Brian Norris).
- PNP subsystem cleanups (Peter Huewe, Rafael J Wysocki).
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=erd3
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-4.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management and ACPI updates from Rafael Wysocki:
"These are mostly fixes and cleanups all over, although there are a few
items that sort of fall into the new feature category.
First off, we have new callbacks for PM domains that should help us to
handle some issues related to device initialization in a better way.
There also is some consolidation in the unified device properties API
area allowing us to use that inferface for accessing data coming from
platform initialization code in addition to firmware-provided data.
We have some new device/CPU IDs in a few drivers, support for new
chips and a new cpufreq driver too.
Specifics:
- Generic PM domains support update including new PM domain callbacks
to handle device initialization better (Russell King, Rafael J
Wysocki, Kevin Hilman)
- Unified device properties API update including a new mechanism for
accessing data provided by platform initialization code (Rafael J
Wysocki, Adrian Hunter)
- ARM cpuidle update including ARM32/ARM64 handling consolidation
(Daniel Lezcano)
- intel_idle update including support for the Silvermont Core in the
Baytrail SOC and for the Airmont Core in the Cherrytrail and
Braswell SOCs (Len Brown, Mathias Krause)
- New cpufreq driver for Hisilicon ACPU (Leo Yan)
- intel_pstate update including support for the Knights Landing chip
(Dasaratharaman Chandramouli, Kristen Carlson Accardi)
- QorIQ cpufreq driver update (Tang Yuantian, Arnd Bergmann)
- powernv cpufreq driver update (Shilpasri G Bhat)
- devfreq update including Tegra support changes (Tomeu Vizoso,
MyungJoo Ham, Chanwoo Choi)
- powercap RAPL (Running-Average Power Limit) driver update including
support for Intel Broadwell server chips (Jacob Pan, Mathias Krause)
- ACPI device enumeration update related to the handling of the
special PRP0001 device ID allowing DT-style 'compatible' property
to be used for ACPI device identification (Rafael J Wysocki)
- ACPI EC driver update including limited _DEP support (Lan Tianyu,
Lv Zheng)
- ACPI backlight driver update including a new mechanism to allow
native backlight handling to be forced on non-Windows 8 systems and
a new quirk for Lenovo Ideapad Z570 (Aaron Lu, Hans de Goede)
- New Windows Vista compatibility quirk for Sony VGN-SR19XN (Chen Yu)
- Assorted ACPI fixes and cleanups (Aaron Lu, Martin Kepplinger,
Masanari Iida, Mika Westerberg, Nan Li, Rafael J Wysocki)
- Fixes related to suspend-to-idle for the iTCO watchdog driver and
the ACPI core system suspend/resume code (Rafael J Wysocki, Chen Yu)
- PM tracing support for the suspend phase of system suspend/resume
transitions (Zhonghui Fu)
- Configurable delay for the system suspend/resume testing facility
(Brian Norris)
- PNP subsystem cleanups (Peter Huewe, Rafael J Wysocki)"
* tag 'pm+acpi-4.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (74 commits)
ACPI / scan: Fix NULL pointer dereference in acpi_companion_match()
ACPI / scan: Rework modalias creation when "compatible" is present
intel_idle: mark cpu id array as __initconst
powercap / RAPL: mark rapl_ids array as __initconst
powercap / RAPL: add ID for Broadwell server
intel_pstate: Knights Landing support
intel_pstate: remove MSR test
cpufreq: fix qoriq uniprocessor build
ACPI / scan: Take the PRP0001 position in the list of IDs into account
ACPI / scan: Simplify acpi_match_device()
ACPI / scan: Generalize of_compatible matching
device property: Introduce firmware node type for platform data
device property: Make it possible to use secondary firmware nodes
PM / watchdog: iTCO: stop watchdog during system suspend
cpufreq: hisilicon: add acpu driver
ACPI / EC: Call acpi_walk_dep_device_list() after installing EC opregion handler
cpufreq: powernv: Report cpu frequency throttling
intel_idle: Add support for the Airmont Core in the Cherrytrail and Braswell SOCs
intel_idle: Update support for Silvermont Core in Baytrail SOC
PM / devfreq: tegra: Register governor on module init
...
Pull irq core updates from Thomas Gleixner:
"Managerial summary:
Core code:
- final removal of IRQF_DISABLED
- new state save/restore functions for virtualization support
- wakeup support for stacked irqdomains
- new function to solve the netpoll synchronization problem
irqchips:
- new driver for STi based devices
- new driver for Vybrid MSCM
- massive cleanup of the GIC driver by moving the GIC-addons to
stacked irqdomains
- the usual pile of fixes and updates to the various chip drivers"
* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (44 commits)
irqchip: GICv3: Add support for irq_[get, set]_irqchip_state()
irqchip: GIC: Add support for irq_[get, set]_irqchip_state()
genirq: Allow the irqchip state of an IRQ to be save/restored
genirq: MSI: Fix freeing of unallocated MSI
irqchip: renesas-irqc: Add wake-up support
irqchip: armada-370-xp: Allow using wakeup source
irqchip: mips-gic: Add new functions to start/stop the GIC counter
irqchip: tegra: Add Tegra210 support
irqchip: digicolor: Move digicolor_set_gc to init section
irqchip: renesas-irqc: Add functional clock to bindings
irqchip: renesas-irqc: Add minimal runtime PM support
irqchip: renesas-irqc: Add more register documentation
DT: exynos: update PMU binding
ARM: exynos4/5: convert pmu wakeup to stacked domains
irqchip: gic: Don't complain in gic_get_cpumask() if UP system
ARM: zynq: switch from gic_arch_extn to gic_set_irqchip_flags
ARM: ux500: switch from gic_arch_extn to gic_set_irqchip_flags
ARM: shmobile: remove use of gic_arch_extn.irq_set_wake
irqchip: gic: Add an entry point to set up irqchip flags
ARM: omap: convert wakeupgen to stacked domains
...
- Add support for marking HPI as broken through devicetree
- Enable runtime PM management of host devices
- Remove the ->enable|disable() callbacks
- Restructure code and cleanups
- Refreshed some of the MMC sections in MAINTAINERS
MMC host:
- dw_mmc: HS400 mode support
- dw_mmc: Add the cmd11 timer to detect a timeout
- dw_mmc: Endian agnostic IO accessors
- dw_mmc: Bugfixes
- sh_mmcif: Add exclusion between cmd and interrupt
- omap_hsmmc: Hibernation support
- omap_hsmmc: Rework and simplify cover/card detect
- omap_hsmmc: Stop using ->enable|disable() callbacks
- atmel-mci: Endian agnostic IO
- sunxi: Enable MMC_CAP_SDIO_IRQ
- sdhci-st: Add support for the stih407 family silicon
- sdhci-st: UHS card support in SDR104 mode
- sdhci-st: HS200 mode support
- sdhci-esdhc-imx: Use common mmc DT parser
- sdhci-of-arasan: Use common mmc DT parser
- sdhci-iproc: Add new driver for Broadcom IPROC SDHCI controller
- sdhci-tegra: Convert to GPIO descriptors
- sdhci-tegra: Optmize write_w path for tegra114 and later
- sdhci-sirf: Update tuning procedure
- sdhci: Fix card presence logic
- sdhci: Cleanups and consolidation
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=mKlf
-----END PGP SIGNATURE-----
Merge tag 'mmc-v4.1' of git://git.linaro.org/people/ulf.hansson/mmc
Pull MMC updates from Ulf Hansson:
"MMC core:
- Add support for marking HPI as broken through devicetree
- Enable runtime PM management of host devices
- Remove the ->enable|disable() callbacks
- Restructure code and cleanups
- Refreshed some of the MMC sections in MAINTAINERS
MMC host:
- dw_mmc: HS400 mode support
- dw_mmc: Add the cmd11 timer to detect a timeout
- dw_mmc: Endian agnostic IO accessors
- dw_mmc: Bugfixes
- sh_mmcif: Add exclusion between cmd and interrupt
- omap_hsmmc: Hibernation support
- omap_hsmmc: Rework and simplify cover/card detect
- omap_hsmmc: Stop using ->enable|disable() callbacks
- atmel-mci: Endian agnostic IO
- sunxi: Enable MMC_CAP_SDIO_IRQ
- sdhci-st: Add support for the stih407 family silicon
- sdhci-st: UHS card support in SDR104 mode
- sdhci-st: HS200 mode support
- sdhci-esdhc-imx: Use common mmc DT parser
- sdhci-of-arasan: Use common mmc DT parser
- sdhci-iproc: Add new driver for Broadcom IPROC SDHCI controller
- sdhci-tegra: Convert to GPIO descriptors
- sdhci-tegra: Optmize write_w path for tegra114 and later
- sdhci-sirf: Update tuning procedure
- sdhci: Fix card presence logic
- sdhci: Cleanups and consolidation"
* tag 'mmc-v4.1' of git://git.linaro.org/people/ulf.hansson/mmc: (79 commits)
mmc: sdhci-st: Update ST SDHCI binding documentation.
mmc: sdhci-st: Update the quirks for this controller.
mmc: sdhci-st: Add sdhci_st_set_uhs_signaling function.
mmc: sdhci-st: Add st_mmcss_cconfig function to configure mmcss glue registers.
mmc: sdhci-st: Add delay management functions for top registers (eMMC).
mmc: sdhci-st: Add support for de-asserting reset signal and top regs resource
mmc: sdhci-st: Add macros for register offsets and bitfields for mmcss glue regs
mmc: sdhci-esdhc-imx: Call mmc_of_parse()
mmc: dw_mmc: Add locking around cmd11 timer
mmc: dw_mmc: Add a return in an unexpected cmd11 timeout
mmc: dw_mmc: Increase cmd11 timeout to 500ms
mmc: dw_mmc: fix fifo ordering in big endian
mmc: dw_mmc: change idmac descriptor files to __le32
mmc: dw_mmc: make IO accessors endian agnostic
mmc: core: Convert the error field in struct mmc_command|data into an int
mmc: sdhci-of-arasan: Call OF parsing for MMC
mmc: sdhci-pci: fix 64 BIT DMA quirks for rtsx
mmc: Add support for marking hpi as broken through devicetree
mmc: sdhci-tegra: convert to use GPIO descriptors
mmc: omap_hsmmc: use generic slot-gpio isr to manage card detect pin
...
- Purge the gic_arch_extn hacks and abuse by using the new stacked domains
NOTE: Due to the nature of these changes, patches crossing subsystems have
been kept together in their own branches.
- tegra
- Handle the LIC properly
- omap
- Convert crossbar to stacked domains
- kill arm,routable-irqs in GIC binding
- exynos
- Convert PMU wakeup to stacked domains
- shmobile, ux500, zynq (irq_set_wake branch)
- Switch from abusing gic_arch_extn to using gic_set_irqchip_flags
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=IPgJ
-----END PGP SIGNATURE-----
Merge tag 'irqchip-core-4.1-3' of git://git.infradead.org/users/jcooper/linux into irq/core
irqchip core change for v4.1 (round 3) from Jason Cooper
Purge the gic_arch_extn hacks and abuse by using the new stacked domains
NOTE: Due to the nature of these changes, patches crossing subsystems have
been kept together in their own branches.
- tegra
- Handle the LIC properly
- omap
- Convert crossbar to stacked domains
- kill arm,routable-irqs in GIC binding
- exynos
- Convert PMU wakeup to stacked domains
- shmobile, ux500, zynq (irq_set_wake branch)
- Switch from abusing gic_arch_extn to using gic_set_irqchip_flags
This series reworks some of the CCI-400 PMU code so that it can be used
on both ARM and ARM64-based systems, without the need to boot in secure
mode on the latter. This paves the way for CCI-500 support in future.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABCgAGBQJVFWAiAAoJELescNyEwWM0pK8IALUinCT+Ec/Oi5WwGJaLgQgw
exlDFAcmml0xisxglGL7eHcvNBs/j4wFD37mqDUszrGW3jrM+Ex+/cvUzWIlEyZl
LjG99ZF2j51LFxDHMgpRwg1aD/NNQsQjwsuHHdCr+NHB5R2C0M4umsgX6Kt6/PE4
95LOnnjBOx4FkMOG9mZElzldUlqnhWd6drjQ9qZQar9VVVewfbR1LH/xQhjrCL0w
nwRzJwYj1LnLFO0hBVUAJSfvYltMF9PxBEx0FkyzN7QcuP1tLQ25NmGEvarHP6iZ
XpvTZ7akzButyUQbvz/kf6a0agPNUv1HHEqh7/Zddvgm//+p8nEBORuJ/cC6g1E=
=UHCi
-----END PGP SIGNATURE-----
Merge tag 'arm-perf-4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/will/linux into next/drivers
Merge "arm-cci PMU updates for 4.1" from Will Deacon:
CCI-400 PMU updates
This series reworks some of the CCI-400 PMU code so that it can be used
on both ARM and ARM64-based systems, without the need to boot in secure
mode on the latter. This paves the way for CCI-500 support in future.
* tag 'arm-perf-4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/will/linux:
arm-cci: Fix CCI PMU event validation
arm-cci: Split the code for PMU vs driver support
arm-cci: Get rid of secure transactions for PMU driver
arm-cci: Abstract the CCI400 PMU specific definitions
arm-cci: Rearrange code for splitting PMU vs driver code
drivers: cci: reject groups spanning multiple HW PMUs
+ Linux 4.0-rc4
Signed-off-by: Olof Johansson <olof@lixom.net>
Replace the clockevents_notify() call with an explicit function call.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Tony Lindgren <tony@atomide.com>
Link: http://lkml.kernel.org/r/3123047.uVjevtxDV7@vostro.rjw.lan
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Replace the clockevents_notify() call with an explicit function call.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Tony Lindgren <tony@atomide.com>
Link: http://lkml.kernel.org/r/2124877.3nbWGILHCV@vostro.rjw.lan
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The omap3isp MMIO register block is contiguous in the MMIO register space
apart from the fact that the ISP IOMMU register block is in the middle of
the area. Ioremap it at two occasions, and keep the rest of the layout of
the register space internal to the omap3isp driver.
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The syscon register isn't part of the ISP, use it through the syscom driver
regmap instead. The syscom block is considered to be from 343x on ISP
revision 2.0 whereas 15.0 is assumed to have 3630 syscon.
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Make omap3isp configuration data structures more suitable for consumption by
the DT by separating the I2C bus information of all the sub-devices in a
group and the ISP bus information from each other. The ISP bus information
is made a pointer instead of being directly embedded in the struct.
In the case of the DT only the sensor specific information on the ISP bus
configuration is retained. The structs are renamed to reflect that.
After this change the structs needed to describe device configuration can be
allocated and accessed separately without those needed only in the case of
platform data. The platform data related structs can be later removed once
the support for platform data can be removed.
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Acked-by: Igor Grinberg <grinberg@compulab.co.il> (for cm-t35)
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
OMAP4, OMAP5 and DRA7 now parse DT entries for control module address spaces,
and set up syscon mappings appropriately. Low level IO init is updated to
remove the legacy control module mappings for these devices also.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
omap4_ctrl_pad_readl/writel are no longer used by anybody, so remove
these. Syscon / pinctrl should be used to access the padconf area
instead.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
The legacy control module APIs will be gone, thus convert the display
driver to use syscon. This change should eventually be moved to
display driver from the board directory.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
This patch creates an l4_wkup interconnect for AM43xx, and moves some of
the generic peripherals under it. System control module nodes are moved
under this new interconnect also, and the SCM clock layout is changed
to use the renamed SCM nodea as the clock provider.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
This patch creates an l4_wkup interconnect for AM33xx, and moves some of
the generic peripherals under it. System control module nodes are moved
under this new interconnect also, and the SCM clock layout is changed
to use the renamed SCM node as the clock provider.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
This patch creates an l4_core interconnect for OMAP3, and moves some
of the generic peripherals under it. System control module nodes are
moved under this new interconnect also, and the SCM clock layout
is changed to use the renamed SCM node as the clock provider.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Reported-by: Tony Lindgren <tony@atomide.com>
This patch creates an l4 / l4-wkup interconnects for omap2420 / omap2430
SoCs, and moves some of the generic peripherals under it. System control
module nodes are moved under this new interconnect also, and the SCM
clock layout is changed to use the new SCM node as the clock provider.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Control module driver needs to support syscon for register accesses, as
the DT hierarchy for control module driver is going to be changed. All
the control module related features will be moved under control module
node, including clocks, pinctrl, and generic configuration register
access. Temporary iomap is still provided very early in the boot for
access while syscon is not yet ready.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
There is no need to read the register with every invocation of the function,
as the value is constant. Thus, cache the value in a static variable.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Some of the TI clock providers will be converted to use syscon, thus
low-level regmap support is needed for the clock drivers also. This
patch adds this support, which can be enabled for individual drivers
in later patches.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
The compatible DT node is now passed with the prm init, so there is no
need to do node matching here again. Added a new flag to the init data
also, to detect default IRQ support for OMAP4. Also, any booting omap4
DT setup always has a PRM node, so there is no need to check against
the special case where it would be missing.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Currently some cpu_is_X checks are used to setup prm_features, however
the same can be accomplished by just passing these flags from the PRM
init data. This is done in preparation to make PRM a separate driver.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
This gets rid of need for some exported driver APIs, and simplifies the
initialization of the CM driver. Done in preparation to make CM a
separate driver. The init data is now also passed to the SoC specific
implementations, allowing future expansion to add feature flags etc.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
PRM device instance offset is now provided through the prm_init_data.
This gets rid of some cpu_is_X / soc_is_X calls from PRM core code,
preparing for PRM to be its own separate driver.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
This gets rid of need for some exported driver APIs, and simplifies the
initialization of the PRM driver. Done in preparation to make PRM a
separate driver. The init data is now also passed to the SoC specific
implementations, allowing future expansion to add feature flags etc.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
ARM errata 798181 is applicable for OMAP5/DRA7 based devices. So enable
the same in the build.
DRA7xx is based on Cortex-A15 r2p2 revision.
ARM Errata extract and workaround information is as below.
On Cortex-A15 (r0p0..r3p2) the TLBI*IS/DSB operations are not
adequately shooting down all use of the old entries. The
ARM_ERRATA_798181 option enables the Linux kernel workaround
for this erratum which sends an IPI to the CPUs that are running
the same ASID as the one being invalidated.
Signed-off-by: Praneeth Bajjuri <praneeth@ti.com>
Acked-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add support for the AM43xx HDQ/1-wire driver and fix the GPTIMER data
for DRA7xx.
Note that I do not have AM43xx nor DRA7xx boards, and cannot test these
patches on those platforms.
Basic build, boot, and PM test logs are available at:
http://www.pwsan.com/omap/testlogs/omap-hwmod-a-for-v4.1/20150324185246/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=LU/x
-----END PGP SIGNATURE-----
Merge tag 'for-v4.1/omap-hwmod-a' of git://git.kernel.org/pub/scm/linux/kernel/git/pjw/omap-pending into omap-for-v4.1/soc
OMAP hwmod data changes for AM43xx and DRA7xx for v4.1
Add support for the AM43xx HDQ/1-wire driver and fix the GPTIMER data
for DRA7xx.
Note that I do not have AM43xx nor DRA7xx boards, and cannot test these
patches on those platforms.
Basic build, boot, and PM test logs are available at:
http://www.pwsan.com/omap/testlogs/omap-hwmod-a-for-v4.1/20150324185246/
board-rx51 has no card detect pin in the mmc slot, but can detect that
the (cell-phone) cover has been removed and the card is accessible.
The semantics between cover/card detect differ, the gpio on the slot
informs you after the card has been removed, cover removal does not
necessarily mean that the card has been removed.
This means different code paths are necessary. To complete this we
also want different fields in the platform data for cover and card
detect. This separation is not pushed all the way down into struct
omap2_hsmmc_info which is used to initialize the platform data.
If we did that we had to go over all board files and set the new
gpio_cod pin to -EINVAL. If we forget one board or some out-of-tree
archicture forgets that the default '0' is used which is a valid pin
number.
Signed-off-by: Andreas Fenkart <afenkart@gmail.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
There is no need to provide the control module base address through a
low-level API from the low-level IO init, as this information is
available through DT. This patch adds a new API to initialize the
control module though, but mostly makes the old API obsolete. The
old API can be completely removed once OMAP3 is made DT only.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
There is no need to provide the PRM base address through a low-level API
from the low-level IO init, as this information is available through DT.
Re-routed the parsing function to be called from the PRM drivers also to
simplify the implementation under io.c.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Tony Lindgren