Sync code to the same with tk4 pub/lts/0017-kabi, except deleted rue
and wujing. Partners can submit pull requests to this branch, and we
can pick the commits to tk4 pub/lts/0017-kabi easly.
Signed-off-by: Jianping Liu <frankjpliu@tencent.com>
Gitee limit the repo's size to 3GB, to reduce the size of the code,
sync codes to ock 5.4.119-20.0009.21 in one commit.
Signed-off-by: Jianping Liu <frankjpliu@tencent.com>
Sync kernel codes to the same with 590eaf1fec ("Init Repo base on
linux 5.4.32 long term, and add base tlinux kernel interfaces."), which
is from tk4, and it is the base of tk4.
Signed-off-by: Jianping Liu <frankjpliu@tencent.com>
The OMAP3 ISP IOMMU does not have any reset lines, so it didn't
need any pdata previously. The OMAP IOMMU driver now requires the
platform data ops for device_enable/idle on all the IOMMU devices
after commit db8918f61d ("iommu/omap: streamline enable/disable
through runtime pm callbacks") to enable/disable the clocks properly
and maintain the reference count and the omap_hwmod state machine.
So, add these callbacks through iommu pdata quirks for the OMAP3
ISP IOMMU.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The OMAP IOMMU driver requires the device_enable/idle platform
data ops on all the IOMMU devices to be able to enable and disable
the clocks after commit db8918f61d ("iommu/omap: streamline
enable/disable through runtime pm callbacks"). Plug in these
pdata ops for all the existing IOMMUs through pdata quirks to
maintain functionality.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
A few fixes that have trickled in through the merge window:
- Video fixes for OMAP due to panel-dpi driver removal
- Clock fixes for OMAP that broke no-idle quirks + nfsroot on DRA7
- Fixing arch version on ASpeed ast2500
- Two fixes for reset handling on ARM SCMI
-----BEGIN PGP SIGNATURE-----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=s4qF
-----END PGP SIGNATURE-----
Merge tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC fixes from Olof Johansson:
"A few fixes that have trickled in through the merge window:
- Video fixes for OMAP due to panel-dpi driver removal
- Clock fixes for OMAP that broke no-idle quirks + nfsroot on DRA7
- Fixing arch version on ASpeed ast2500
- Two fixes for reset handling on ARM SCMI"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc:
ARM: aspeed: ast2500 is ARMv6K
reset: reset-scmi: add missing handle initialisation
firmware: arm_scmi: reset: fix reset_state assignment in scmi_domain_reset
bus: ti-sysc: Remove unpaired sysc_clkdm_deny_idle()
ARM: dts: logicpd-som-lv: Fix i2c2 and i2c3 Pin mux
ARM: dts: am3517-evm: Fix missing video
ARM: dts: logicpd-torpedo-baseboard: Fix missing video
ARM: omap2plus_defconfig: Fix missing video
bus: ti-sysc: Fix handling of invalid clocks
bus: ti-sysc: Fix clock handling for no-idle quirks
This code is currently unable to find the dts opp tables as ti-cpufreq
needs to set them up first based on speed binning.
We stopped initializing the opp tables with platform code years ago for
device tree based booting with commit 92d51856d7 ("ARM: OMAP3+: do not
register non-dt OPP tables for device tree boot"), and all of mach-omap2
is now booting using device tree.
We currently get the following errors on init:
omap2_set_init_voltage: unable to find boot up OPP for vdd_mpu
omap2_set_init_voltage: unable to set vdd_mpu
omap2_set_init_voltage: unable to find boot up OPP for vdd_core
omap2_set_init_voltage: unable to set vdd_core
omap2_set_init_voltage: unable to find boot up OPP for vdd_iva
omap2_set_init_voltage: unable to set vdd_iva
Let's just drop the unused code. Nowadays ti-cpufreq should be used to
to initialize things properly.
Cc: Adam Ford <aford173@gmail.com>
Cc: André Roth <neolynx@gmail.com>
Cc: "H. Nikolaus Schaller" <hns@goldelico.com>
Cc: Nishanth Menon <nm@ti.com>
Cc: Tero Kristo <t-kristo@ti.com>
Tested-by: Adam Ford <aford173@gmail.com> #logicpd-torpedo-37xx-devkit
Signed-off-by: Tony Lindgren <tony@atomide.com>
TRM "Table 13-34. SYSCONFIG Register Field Descriptions" lists both
standbymode and idlemode that should be just the sidle and midle
registers where midle is currently unconfigured for lcdc_sysc. As
the dts data has been generated based on lcdc_sysc, we now have an
empty "ti,sysc-midle" property.
And so we currently get a warning for lcdc because of a difference
with dts provided configuration compared to the legacy platform
data. This is because lcdc has SYSC_HAS_MIDLEMODE configured in
the platform data without configuring the modes.
Let's fix the issue by adding the missing midlemode to lcdc_sysc,
and configuring the "ti,sysc-midle" property based on the TRM
values.
Fixes: f711c575cf ("ARM: dts: am335x: Add l4 interconnect hierarchy and ti-sysc data")
Cc: Jyri Sarha <jsarha@ti.com>
Cc: Keerthy <j-keerthy@ti.com>
Cc: Robert Nelson <robertcnelson@gmail.com>
Cc: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
For ti,sysc-omap4 compatible devices with no sysstatus register, we do have
reset done status available in the SOFTRESET bit that clears when the reset
is done. This is documented for example in am437x TRM for DMTIMER_TIOCP_CFG
register. The am335x TRM just says that SOFTRESET bit value 1 means reset is
ongoing, but it behaves the same way clearing after reset is done.
With the ti-sysc driver handling this automatically based on no sysstatus
register defined, we see warnings if SYSC_HAS_RESET_STATUS is missing in the
legacy platform data:
ti-sysc 48042000.target-module: sysc_flags 00000222 != 00000022
ti-sysc 48044000.target-module: sysc_flags 00000222 != 00000022
ti-sysc 48046000.target-module: sysc_flags 00000222 != 00000022
...
Let's fix these warnings by adding SYSC_HAS_RESET_STATUS. Let's also
remove the useless parentheses while at it.
If it turns out we do have ti,sysc-omap4 compatible devices without a
working SOFTRESET bit we can set up additional quirk handling for it.
Signed-off-by: Tony Lindgren <tony@atomide.com>
This is some material that we picked up into our tree late or
that had complex inter-depondencies. The fact that there are these
interdependencies tends to meant that these are often actually the most
interesting new additions:
The new Aspeed AST2600 baseboard management controller is added, this
is a Cortex-A7 based follow-up to the ARM11 based AST2500 and had some
dependencies on other device drivers.
After many years, support for the MMP2 based OLPC XO-1.75 finally makes
it into the kernel.
The Armada 3720 based Turris Mox open source router platform is a late
addition and it follows some preparatory work across multiple branches.
The OMAP2+ platform had some large-scale cleanup involving driver
changes and DT changes, here we finish it off, dropping a lot of the
now-unused platform data.
The TI K3 platform that got added for 5.3 gains a lot more support
for individual bits on the SoC, this part just came late for the
merge window.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=Qtkp
-----END PGP SIGNATURE-----
Merge tag 'armsoc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC late updates from Arnd Bergmann:
"This is some material that we picked up into our tree late or that had
complex inter-depondencies. The fact that there are these
interdependencies tends to meant that these are often actually the
most interesting new additions:
- The new Aspeed AST2600 baseboard management controller is added,
this is a Cortex-A7 based follow-up to the ARM11 based AST2500 and
had some dependencies on other device drivers.
- After many years, support for the MMP2 based OLPC XO-1.75 finally
makes it into the kernel.
- The Armada 3720 based Turris Mox open source router platform is a
late addition and it follows some preparatory work across multiple
branches.
- The OMAP2+ platform had some large-scale cleanup involving driver
changes and DT changes, here we finish it off, dropping a lot of
the now-unused platform data.
- The TI K3 platform that got added for 5.3 gains a lot more support
for individual bits on the SoC, this part just came late for the
merge window"
[ This pull request itself wasn't actually sent late at all by Arnd, but
I waited on the branches that it used to be pulled first, so it ends
up being merged much later than the other ARM SoC pull requests this
merge window - Linus ]
* tag 'armsoc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (57 commits)
ARM: dts: dir685: Drop spi-cpol from the display
ARM: dts: aspeed: Add AST2600 pinmux nodes
ARM: dts: aspeed: Add AST2600 and EVB
ARM: exynos: Enable support for ARM architected timers
ARM: samsung: Fix system restart on S3C6410
ARM: dts: mmp2: add OLPC XO 1.75 machine
ARM: dts: mmp2: rename the USB PHY node
ARM: dts: mmp2: specify reg-shift for the UARTs
ARM: dts: mmp2: add camera interfaces
ARM: dts: mmp2: fix the SPI nodes
ARM: dts: mmp2: trivial whitespace fix
arm64: dts: marvell: add DTS for Turris Mox
dt-bindings: marvell: document Turris Mox compatible
arm64: dts: marvell: armada-37xx: add SPI CS1 pinctrl
arm64: dts: ti: k3-j721e-main: Fix gic-its node unit-address
arm64: dts: ti: k3-am65-main: Fix gic-its node unit-address
arm64: dts: ti: k3-j721e-main: Add hwspinlock node
arm64: dts: ti: k3-am65-main: Add hwspinlock node
arm64: dts: k3-j721e: Add gpio-keys on common processor board
dt-bindings: pinctrl: k3: Introduce pinmux definitions for J721E
...
-----BEGIN PGP SIGNATURE-----
iQIzBAABCAAdFiEE+QmuaPwR3wnBdVwACF8+vY7k4RUFAl1/essACgkQCF8+vY7k
4RV4YQ/+IILxwEuXn6cU2H/ss2+6QmOdOYISGDniWRQGTE9NN4AuvF7jv3qxek5o
FqisJXFJWCzpO7+LpKomAQXweWmVGaSV99QSJhRUyM0lNIrXD+rACO77yYL5ZwSX
r5REvk+ykozgRrQrWpiHCGOyH08Kt/LO/jA29VaJokX6yX4w0xvRc0rUBe2OlL+K
rcaXDnVw8SloVpyDaMY0DDqP8v0iGsUufTxFwAoskL36+qudXgunrg1yoNwmvTL+
spxLFs/I2LBIuBdvSg5W+FmwC3YnMdE/BDiaor9jKvhqUT9hOIozZ+pNmVTEsfvk
1FdTobf2mhvzmJrn4bdQSfFb7BiDNgMuf6/IpeRJqQSpQHzyHQhVGBG8h3axSOhM
5QWHBqrA0MAhcwVsKBUKj+mcfg7uNxtGPqmoeSVlMz+LH1hhokNWTAq5p2FgiDh8
wrSsZyJItHg2hbXPkWP9EgA40Q/xzwsvUCvoz0/+dCd08DwIeSi2HIQbNddxg7y8
NllZY0o4h6ETeDIfQb6k3zrRnAqOwlxxvXIMlaGanYegZBXMltiBIqiWrUG1qQh5
CrBTAE28vBCNNTxQJyEjut6H5/RpWEFwebcUkn1BkeUAPZ1w72+LTJ/obekiC0/6
Dxv7VvoTG+UFO14Fz7L3lYYTK2+OGvAsuXHAhQgrW5bWfmm8Cog=
=QTT+
-----END PGP SIGNATURE-----
Merge tag 'media/v5.4-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
- a new sensor driver for ov5675
- a new platform driver for Allwinner A10 sensor interface
- some new remote controller keymaps
- some cosmetic changes at V4L2 core in order to avoid #ifdefs and to
merge two core modules into one
- removal of bcm2048 radio driver from staging
- removal of davinci_vpfe video driver from staging
- regression fix since Kernel 5.1 at the legacy VideoBuffer version 1
core
- added some documentation for remote controller protocols
- pixel format documentation was split on two files
- lots of other driver improvements and cleanups
* tag 'media/v5.4-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (321 commits)
media: videobuf-core.c: poll_wait needs a non-NULL buf pointer
media: sun4i: Make sun4i_csi_formats static
media: imx: remove unused including <linux/version.h>
media: stm32-dcmi: Delete an unnecessary of_node_put() call in dcmi_probe()
media: pvrusb2: qctrl.flag will be uninitlaized if cx2341x_ctrl_query() returns error code
media: em28xx: Fix exception handling in em28xx_alloc_urbs()
media: don't do a 31 bit shift on a signed int
media: use the BIT() macro
media: ov9650: add a sanity check
media: aspeed-video: address a protential usage of an unitialized var
media: vicodec: make life easier for static analyzers
media: remove include stdarg.h from some drivers
v4l2-core: fix coding style for the two new c files
media: v4l2-core: Remove BUG() from i2c and spi helpers
media: v4l2-core: introduce a helper to unregister a i2c subdev
media: v4l2-core: introduce a helper to unregister a spi subdev
media: v4l2-core: move i2c helpers out of v4l2-common.c
media: v4l2-core: move spi helpers out of v4l2-common.c
media: v4l2-core: Module re-organization
media: usbvision: Remove dead code
...
The main change this time around is a cleanup of some of the oldest
platforms based on the XScale and ARM9 CPU cores, which are between 10
and 20 years old.
The Kendin/Micrel/Microchip KS8695, Winbond/Nuvoton W90x900 and Intel
IOP33x/IOP13xx platforms are removed after we determined that nobody is
using them any more.
The TI Davinci and NXP LPC32xx platforms on the other hand are still in
active use and are converted to the ARCH_MULTIPLATFORM build, meaning
that we can compile a kernel that works on these along with most other
ARMv5 platforms. Changes toward that goal are also merged for IOP32x,
but additional work is needed to complete this. Patches for the
remaining ARMv5 platforms have started but need more work and some
testing.
Support for the new ASpeed AST2600 gets added, this is based on the
Cortex-A7 ARMv7 core, and is a newer version of the existing ARMv5 and
ARMv6 chips in the same family.
Other changes include a cleanup of the ST-Ericsson ux500 platform
and the move of the TI Davinci platform to a new clocksource driver.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=u+ew
-----END PGP SIGNATURE-----
Merge tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC platform updates from Arnd Bergmann:
"The main change this time around is a cleanup of some of the oldest
platforms based on the XScale and ARM9 CPU cores, which are between 10
and 20 years old.
The Kendin/Micrel/Microchip KS8695, Winbond/Nuvoton W90x900 and Intel
IOP33x/IOP13xx platforms are removed after we determined that nobody
is using them any more.
The TI Davinci and NXP LPC32xx platforms on the other hand are still
in active use and are converted to the ARCH_MULTIPLATFORM build,
meaning that we can compile a kernel that works on these along with
most other ARMv5 platforms. Changes toward that goal are also merged
for IOP32x, but additional work is needed to complete this. Patches
for the remaining ARMv5 platforms have started but need more work and
some testing.
Support for the new ASpeed AST2600 gets added, this is based on the
Cortex-A7 ARMv7 core, and is a newer version of the existing ARMv5 and
ARMv6 chips in the same family.
Other changes include a cleanup of the ST-Ericsson ux500 platform and
the move of the TI Davinci platform to a new clocksource driver"
[ The changes had marked INTEL_IOP_ADMA and USB_LPC32XX as being
buildable on other platforms through COMPILE_TEST, but that causes new
warnings that I most definitely do not want to see during the merge
window as that could hide other issues.
So the COMPILE_TEST option got disabled for them again - Linus ]
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (61 commits)
ARM: multi_v5_defconfig: make DaVinci part of the ARM v5 multiplatform build
ARM: davinci: support multiplatform build for ARM v5
arm64: exynos: Enable exynos-chipid driver
ARM: OMAP2+: Delete an unnecessary kfree() call in omap_hsmmc_pdata_init()
ARM: OMAP2+: move platform-specific asm-offset.h to arch/arm/mach-omap2
ARM: davinci: dm646x: Fix a typo in the comment
ARM: davinci: dm646x: switch to using the clocksource driver
ARM: davinci: dm644x: switch to using the clocksource driver
ARM: aspeed: Enable SMP boot
ARM: aspeed: Add ASPEED AST2600 architecture
ARM: aspeed: Select timer in each SoC
dt-bindings: arm: cpus: Add ASPEED SMP
ARM: imx: stop adjusting ar8031 phy tx delay
mailmap: map old company name to new one @microchip.com
MAINTAINERS: at91: remove the TC entry
MAINTAINERS: at91: Collect all pinctrl/gpio drivers in same entry
ARM: at91: move platform-specific asm-offset.h to arch/arm/mach-at91
MAINTAINERS: Extend patterns for Samsung SoC, Security Subsystem and clock drivers
ARM: s3c64xx: squash samsung_usb_phy.h into setup-usb-phy.c
ARM: debug-ll: Add support for r7s9210
...
We can currently get "Unable to handle kernel paging request at
virtual address" for invalid clocks with dts node but no driver:
(__clk_get_hw) from [<c0138ebc>] (ti_sysc_find_one_clockdomain+0x18/0x34)
(ti_sysc_find_one_clockdomain) from [<c0138f0c>] (ti_sysc_clkdm_init+0x34/0xdc)
(ti_sysc_clkdm_init) from [<c0584660>] (sysc_probe+0xa50/0x10e8)
(sysc_probe) from [<c065c6ac>] (platform_drv_probe+0x58/0xa8)
Let's add IS_ERR checks to ti_sysc_clkdm_init() as And let's start treating
clk_get() with -ENOENT as a proper error. If the clock name is specified
in device tree we must succeed with clk_get() to continue. For modules with
no clock names specified in device tree we will just ignore the clocks.
Fixes: 2b2f7def05 ("bus: ti-sysc: Add support for missing clockdomain handling")
Acked-by: Roger Quadros <rogerq@ti.com>
Tested-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
For a while we've had omap4 sgx glue layer defined in dts and probed
with ti-sysc driver. This allows idling the sgx module for PM, and
removes the need for custom platform glue layer code for any further
driver changes.
We first drop the unused legacy platform data for omap4 sgx. Then for
omap5, we need add the missing clkctrl clock data so we can configure
sgx. And we configure sgx for omap34xx, omap36xx and am3517.
For am335x, we still have a dependency for rstctrl reset driver changes,
so that will be added later on.
Note that this branch is based on earlier ti-sysc branch for omap36xx
glue layer quirk handling.
-----BEGIN PGP SIGNATURE-----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=a2cp
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v5.4/ti-sysc-sgx-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into arm/late
SoC glue layer changes for SGX on omap variants for v5.4
For a while we've had omap4 sgx glue layer defined in dts and probed
with ti-sysc driver. This allows idling the sgx module for PM, and
removes the need for custom platform glue layer code for any further
driver changes.
We first drop the unused legacy platform data for omap4 sgx. Then for
omap5, we need add the missing clkctrl clock data so we can configure
sgx. And we configure sgx for omap34xx, omap36xx and am3517.
For am335x, we still have a dependency for rstctrl reset driver changes,
so that will be added later on.
Note that this branch is based on earlier ti-sysc branch for omap36xx
glue layer quirk handling.
* tag 'omap-for-v5.4/ti-sysc-sgx-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: ARM: dts: Configure interconnect target module for am3517sgx
ARM: dts: Configure interconnect target module for omap3 sgx
ARM: dts: Configure sgx for omap5
clk: ti: add clkctrl data omap5 sgx
ARM: OMAP2+: Drop legacy platform data for omap4 gpu
Link: https://lore.kernel.org/r/pull-1567016893-318461@atomide.com-4
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
We can now drop more platform data in favor of dts data for most
devices like cpsw, gpio, i2c, mmc, uart and watchdog.
In general we can do this by dropping legacy "ti,hwmods" custom dts
property, and the platform data assuming the related dts data is correct.
This is best done as single patch as otherwise we'd have to revert two
patches in case of any unexpected issues, and we're just removing data.
Fro cpsw, before we can do this, we need to configure the cpsw mdio clocks
properly in dts though in the first patch. For omap4 i2c, we've already
dropped the platform data earlier, but have been still allocting it
dynamically based on the dts data based on the "ti,hwmods" property, but
that is no longer needed. For d2d, we are missing the dts data, so we
first add it and then drop the platform data.
For dra7, we drop platform data and "ti,hwmods" for mcasp and mcspi.
We've already dropped platform data earlier for gpio, i2c, mmc, and
uart so we just need to drop "ti,hwmods" property for those.
Note that this branch is based on earlier ti-sysc-fixes branch.
-----BEGIN PGP SIGNATURE-----
iQJFBAABCAAvFiEEkgNvrZJU/QSQYIcQG9Q+yVyrpXMFAl1mxxsRHHRvbnlAYXRv
bWlkZS5jb20ACgkQG9Q+yVyrpXOoPhAAxRtVcr86Fsb535T6/Zy4wKpshvDIXrlZ
AxfT+NlDxgsZRWSTFYlRIPxEyWpIQDDBL34Y4UMO2gKB0pWGhFfiuUi2SNXntWaj
VsM5QeMAG/9LFIdUw08XwR/ahrUQnBbNNkHkw/7mL/q/Tsu3NDeIV4ipSz5Qj7vE
SljP/8DTTkR8TyUWBy3p64UZctx/QMdurg3zuwqCiT3wWEVQRnFesTS1zCzhbZId
sDbvYc46CaIkgNjlsCgzZuBIpbLH7EtJWZXb01DAqVVidCaO6r82BvAqfXcDCLwj
sOZOFBQ77ch+zpjlPcYv99TIOQFWnrCIXzKpZfZIJkO6Iu6ugGvPFN99x6WTHZLC
fGLPz6I9qaObuHLuypkcJCOVmGGQmDJiKnAruJX5peOmLQlV4UaYhNoLkQv3RSC+
6XeSB0+ycVu2CY35kNwTNVWOGVOYC8a8Umw5pUPVHn94DZgr4qmHEy9Jv0/S0BNy
04ldN5rufhFBK2A0Vs9HKGRgQfYZ1l2MHxB7LGMFt0jXxzZWGcl7HqZWGcWIuLDr
ohjwKVCGS6SCofC5qSxAzrdasqhkR/V7Yi0uge2PYGrLX7evoD5fIZADrUcVXcRS
KI9jcj/7+OTCd9QbkobHGFYa6HZN/66jp0uhnoToTNhbGQXDDGhG5U7Zd+bWXP6i
nBc7gmpXJEo=
=mBPp
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v5.4/ti-sysc-drop-pdata-take2-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into arm/late
Drop legacy platform data omap variants for v5.4
We can now drop more platform data in favor of dts data for most
devices like cpsw, gpio, i2c, mmc, uart and watchdog.
In general we can do this by dropping legacy "ti,hwmods" custom dts
property, and the platform data assuming the related dts data is correct.
This is best done as single patch as otherwise we'd have to revert two
patches in case of any unexpected issues, and we're just removing data.
Fro cpsw, before we can do this, we need to configure the cpsw mdio clocks
properly in dts though in the first patch. For omap4 i2c, we've already
dropped the platform data earlier, but have been still allocting it
dynamically based on the dts data based on the "ti,hwmods" property, but
that is no longer needed. For d2d, we are missing the dts data, so we
first add it and then drop the platform data.
For dra7, we drop platform data and "ti,hwmods" for mcasp and mcspi.
We've already dropped platform data earlier for gpio, i2c, mmc, and
uart so we just need to drop "ti,hwmods" property for those.
Note that this branch is based on earlier ti-sysc-fixes branch.
* tag 'omap-for-v5.4/ti-sysc-drop-pdata-take2-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: Drop legacy custom hwmods property for dra7 gpio
ARM: dts: Drop legacy custom hwmods property for dra7 mmc
ARM: dts: Drop legacy custom hwmods property for dra7 i2c
ARM: dts: Drop legacy custom hwmods property for dra7 uart
ARM: OMAP2+: Drop legacy platform data for dra7 mcasp
ARM: OMAP2+: Drop legacy platform data for dra7 mcspi
ARM: OMAP2+: Drop legacy platform data for omap4 d2d
ARM: dts: Configure d2d dts data for omap4
ARM: OMAP2+: Drop legacy watchdog platform data for omap4
ARM: dts: Drop custom hwmod property for omap4 i2c
ARM: OMAP2+: Drop legacy platform data for cpsw on dra7
ARM: OMAP2+: Drop legacy platform data for cpsw on am3 and am4
ARM: dts: Add fck for cpsw mdio for omap variants
Link: https://lore.kernel.org/r/pull-1567016893-318461@atomide.com-3
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
With recent ti-sysc driver changes, we can probe most devices with device
tree data only and drop the custom "ti,hwmods" property.
Let's drop the legacy platform data and custom "ti,hwmods" property. We
want to do this in a single patch as the "ti,hwmods" property is used to
allocate platform data dynamically that we no longer want to do.
Cc: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
With recent ti-sysc driver changes, we can probe most devices with device
tree data only and drop the custom "ti,hwmods" property.
Let's drop the legacy platform data and custom "ti,hwmods" property. We
want to do this in a single patch as the "ti,hwmods" property is used to
allocate platform data dynamically that we no longer want to do.
Cc: Vignesh R <vigneshr@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
A null pointer would be passed to a call of the function "kfree" directly
after a call of the function "kzalloc" failed at one place.
Remove this superfluous function call.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
<generated/ti-pm-asm-offsets.h> is only generated and included by
arch/arm/mach-omap2/, so it does not need to reside in the globally
visible include/generated/.
I renamed it to arch/arm/mach-omap2/pm-asm-offsets.h since the prefix
'ti-' is just redundant in mach-omap2/.
My main motivation of this change is to avoid the race condition for
the parallel build (-j) when CONFIG_IKHEADERS is enabled.
When it is enabled, all the headers under include/ are archived into
kernel/kheaders_data.tar.xz and exposed in the sysfs.
In the parallel build, we have no idea in which order files are built.
- If ti-pm-asm-offsets.h is built before kheaders_data.tar.xz,
the header will be included in the archive. Probably nobody will
use it, but it is harmless except that it will increase the archive
size needlessly.
- If kheaders_data.tar.xz is built before ti-pm-asm-offsets.h,
the header will not be included in the archive. However, in the next
build, the archive will be re-generated to include the newly-found
ti-pm-asm-offsets.h. This is not nice from the build system point
of view.
- If ti-pm-asm-offsets.h and kheaders_data.tar.xz are built at the
same time, the corrupted header might be included in the archive,
which does not look nice either.
This commit fixes the race.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Tested-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
I've tested that the interconnect target module enables and idles
just fine when probed with ti-sysc with PM runtime control via sys:
# echo on > $(find /sys -name control | grep \/5601)
# rwmem 0x56000024
0x56000024 = 0x00010200 # SGX540 CORE_REVISION
# echo auto > $(find /sys -name control | grep \/5601)
# rwmem 0x56000024
And when idled, it will produce "Bus error" as expected.
Cc: Adam Ford <aford173@gmail.com>
Cc: Filip Matijević <filip.matijevic.pz@gmail.com>
Cc: "H. Nikolaus Schaller" <hns@goldelico.com>
Cc: Ivaylo Dimitrov <ivo.g.dimitrov.75@gmail.com>
Cc: moaz korena <moaz@korena.xyz>
Cc: Merlijn Wajer <merlijn@wizzup.org>
Cc: Paweł Chmiel <pawel.mikolaj.chmiel@gmail.com>
Cc: Philipp Rossak <embed3d@gmail.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with ti-sysc interconnect driver and dts
data. Let's drop the related platform data and custom ti,hwmods
dts property.
As we're just dropping data, and the early platform data init
is based on the custom ti,hwmods property, we want to drop both
the platform data and ti,hwmods property in a single patch.
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with ti-sysc interconnect driver and dts
data. Let's drop the related platform data and custom ti,hwmods
dts property.
As we're just dropping data, and the early platform data init
is based on the custom ti,hwmods property, we want to drop both
the platform data and ti,hwmods property in a single patch.
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe cpsw with ti-sysc interconnect driver and dts
data. Let's drop the related platform data and custom ti,hwmods
dts property for am3 and am4.
As we're just dropping data, and the early platform data init
is based on the custom ti,hwmods property, we want to drop both
the platform data and ti,hwmods property in a single patch.
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Cc: Keerthy <j-keerthy@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe cpsw with ti-sysc interconnect driver and dts
data. Let's drop the related platform data and custom ti,hwmods
dts property for am3 and am4.
As we're just dropping data, and the early platform data init
is based on the custom ti,hwmods property, we want to drop both
the platform data and ti,hwmods property in a single patch.
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Cc: Keerthy <j-keerthy@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We have errata i688 workaround produce warnings on SoCs other than
omap4 and omap5:
omap4_sram_init:Unable to allocate sram needed to handle errata I688
omap4_sram_init:Unable to get sram pool needed to handle errata I688
This is happening because there is no ti,omap4-mpu node, or no SRAM
to configure for the other SoCs, so let's remove the warning based
on the SoC revision checks.
As nobody has complained it seems that the other SoC variants do not
need this workaround.
Signed-off-by: Tony Lindgren <tony@atomide.com>
The dma_mask and coherent_dma_mask values were never set.
This prevented the media omap_vout driver from loading successfully.
Tested on a Pandaboard and Beagle XM board.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Support has been added to the OMAP IOMMU driver to fix a boot hang
issue on OMAP remoteprocs with AMMU/Unicache, caused by an improper
AMMU/Unicache state upon initial deassertion of the processor reset.
The issue is described in detail in the next three paragraphs.
All the Cortex M3/M4 IPU processor subsystems in OMAP SoCs have a
AMMU/Unicache IP that dictates the memory attributes for addresses
seen by the processor cores. The AMMU/Unicache is configured/enabled
by the SCACHE_CONFIG.BYPASS bit - a value of 1 enables the cache and
mandates all addresses accessed by M3/M4 be defined in the AMMU. This
bit is not programmable from the host processor. The M3/M4 boot
sequence starts out with the AMMU/Unicache in disabled state, and
SYS/BIOS programs the AMMU regions and enables the Unicache during
one of its initial boot steps. This SCACHE_CONFIG.BYPASS bit is
however enabled by default whenever a RET reset is applied to the IP,
irrespective of whether it was previously enabled or not. The AMMU
registers lose their context whenever this reset is applied. The reset
is effective as long as the MMU portion of the subsystem is enabled
and clocked. This behavior is common to all the IPU and DSP subsystems
that have an AMMU/Unicache.
The IPU boot sequence involves enabling and programming the MMU, and
loading the processor and releasing the reset(s) for the processor.
The PM setup code currently sets the target state for most of the
power domains to RET. The L2 MMU can be enabled, programmed and
accessed properly just fine with the domain in hardware supervised
mode, while the power domain goes through a RET->ON->RET transition
during the programming sequence. However, the ON->RET transition
asserts a RET reset, and the SCACHE_CONFIG.BYPASS bit gets auto-set.
An AMMU fault is thrown immediately when the M3/M4 core's reset is
released since the first instruction address itself will not be
defined in any valid AMMU regions. The ON->RET transition happens
automatically on the power domain after enabling the iommu due to
the hardware supervised mode.
This patch adds and invokes the .set_pwrdm_constraint pdata ops, if
present, during the OMAP IOMMU enable and disable functions to resolve
the above boot hang issue. The ops will allow to invoke a mach-omap2
layer API pwrdm_set_next_pwrst() in a multi-arch kernel environment.
The ops also returns the current power domain state while enforcing
the constraint so that the driver can store it and use it to set back
the power domain state while releasing the constraint. The pdata ops
implementation restricts the target power domain to ON during enable,
and back to the original power domain state during disable, and thereby
eliminating the conditions for the boot issue. The implementation is
effective only when the original power domain state is either RET or
OFF, and is a no-op when it is ON or INACTIVE.
The .set_pwrdm_constraint ops need to be plugged in pdata-quirks
for the affected remote processors to be able to boot properly.
Note that the current issue is seen only on kernels with the affected
power domains programmed to enter RET. For eg., IPU1 on DRA7xx is in a
separate domain and is susceptible to this bug, while the IPU2 subsystem
is within CORE power domain, and CORE RET is not supported on this SoC.
IPUs on OMAP4 and OMAP5 are also susceptible since they are in CORE power
domain, and CORE RET is a valid power target on these SoCs.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
TRM says PWMSS_SYSCONFIG bit for SOFTRESET changes to zero when
reset is completed. Let's configure it as otherwise we get warnings
on boot when we check the data against dts provided data. Eventually
the legacy platform data will be just dropped, but let's fix the
warning first.
Reviewed-by: Suman Anna <s-anna@ti.com>
Tested-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Various driver updates for platforms and a couple of the small driver
subsystems we merge through our tree:
- A driver for SCU (system control) on NXP i.MX8QXP
- Qualcomm Always-on Subsystem messaging driver (AOSS QMP)
- Qualcomm PM support for MSM8998
- Support for a newer version of DRAM PHY driver for Broadcom (DPFE)
- Reset controller support for Bitmain BM1880
- TI SCI (System Control Interface) support for CPU control on AM654
processors
- More TI sysc refactoring and rework
-----BEGIN PGP SIGNATURE-----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=ek+j
-----END PGP SIGNATURE-----
Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC-related driver updates from Olof Johansson:
"Various driver updates for platforms and a couple of the small driver
subsystems we merge through our tree:
- A driver for SCU (system control) on NXP i.MX8QXP
- Qualcomm Always-on Subsystem messaging driver (AOSS QMP)
- Qualcomm PM support for MSM8998
- Support for a newer version of DRAM PHY driver for Broadcom (DPFE)
- Reset controller support for Bitmain BM1880
- TI SCI (System Control Interface) support for CPU control on AM654
processors
- More TI sysc refactoring and rework"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (84 commits)
reset: remove redundant null check on pointer dev
soc: rockchip: work around clang warning
dt-bindings: reset: imx7: Fix the spelling of 'indices'
soc: imx: Add i.MX8MN SoC driver support
soc: aspeed: lpc-ctrl: Fix probe error handling
soc: qcom: geni: Add support for ACPI
firmware: ti_sci: Fix gcc unused-but-set-variable warning
firmware: ti_sci: Use the correct style for SPDX License Identifier
soc: imx8: Use existing of_root directly
soc: imx8: Fix potential kernel dump in error path
firmware/psci: psci_checker: Park kthreads before stopping them
memory: move jedec_ddr.h from include/memory to drivers/memory/
memory: move jedec_ddr_data.c from lib/ to drivers/memory/
MAINTAINERS: Remove myself as qcom maintainer
soc: aspeed: lpc-ctrl: make parameter optional
soc: qcom: apr: Don't use reg for domain id
soc: qcom: fix QCOM_AOSS_QMP dependency and build errors
memory: tegra: Fix -Wunused-const-variable
firmware: tegra: Early resume BPMP
soc/tegra: Select pinctrl for Tegra194
...
SoC platform changes. Main theme this merge window:
- The Netx platform (Netx 100/500) platform is removed by Linus Walleij--
the SoC doesn't have active maintainers with hardware, and in
discussions with the vendor the agreement was that it's OK to remove.
- Russell King has a series of patches that cleans up and refactors
SA1101 and RiscPC support.
-----BEGIN PGP SIGNATURE-----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=FX6e
-----END PGP SIGNATURE-----
Merge tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC platform updates from Olof Johansson:
"SoC platform changes. Main theme this merge window:
- The Netx platform (Netx 100/500) platform is removed by Linus
Walleij-- the SoC doesn't have active maintainers with hardware,
and in discussions with the vendor the agreement was that it's OK
to remove.
- Russell King has a series of patches that cleans up and refactors
SA1101 and RiscPC support"
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (47 commits)
ARM: stm32: use "depends on" instead of "if" after prompt
ARM: sa1100: convert to common clock framework
ARM: exynos: Cleanup cppcheck shifting warning
ARM: pxa/lubbock: remove lubbock_set_misc_wr() from global view
ARM: exynos: Only build MCPM support if used
arm: add missing include platform-data/atmel.h
ARM: davinci: Use GPIO lookup table for DA850 LEDs
ARM: OMAP2: drop explicit assembler architecture
ARM: use arch_extension directive instead of arch argument
ARM: imx: Switch imx7d to imx-cpufreq-dt for speed-grading
ARM: bcm: Enable PINCTRL for ARCH_BRCMSTB
ARM: bcm: Enable ARCH_HAS_RESET_CONTROLLER for ARCH_BRCMSTB
ARM: riscpc: enable chained scatterlist support
ARM: riscpc: reduce IRQ handling code
ARM: riscpc: move RiscPC assembly files from arch/arm/lib to mach-rpc
ARM: riscpc: parse video information from tagged list
ARM: riscpc: add ecard quirk for Atomwide 3port serial card
MAINTAINERS: mvebu: Add git entry
soc: ti: pm33xx: Add a print while entering RTC only mode with DDR in self-refresh
ARM: OMAP2+: Make some variables static
...
Here is the "big" driver core and debugfs changes for 5.3-rc1
It's a lot of different patches, all across the tree due to some api
changes and lots of debugfs cleanups. Because of this, there is going
to be some merge issues with your tree at the moment, I'll follow up
with the expected resolutions to make it easier for you.
Other than the debugfs cleanups, in this set of changes we have:
- bus iteration function cleanups (will cause build warnings
with s390 and coresight drivers in your tree)
- scripts/get_abi.pl tool to display and parse Documentation/ABI
entries in a simple way
- cleanups to Documenatation/ABI/ entries to make them parse
easier due to typos and other minor things
- default_attrs use for some ktype users
- driver model documentation file conversions to .rst
- compressed firmware file loading
- deferred probe fixes
All of these have been in linux-next for a while, with a bunch of merge
issues that Stephen has been patient with me for. Other than the merge
issues, functionality is working properly in linux-next :)
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXSgpnQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykcwgCfS30OR4JmwZydWGJ7zK/cHqk+KjsAnjOxjC1K
LpRyb3zX29oChFaZkc5a
=XrEZ
-----END PGP SIGNATURE-----
Merge tag 'driver-core-5.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core and debugfs updates from Greg KH:
"Here is the "big" driver core and debugfs changes for 5.3-rc1
It's a lot of different patches, all across the tree due to some api
changes and lots of debugfs cleanups.
Other than the debugfs cleanups, in this set of changes we have:
- bus iteration function cleanups
- scripts/get_abi.pl tool to display and parse Documentation/ABI
entries in a simple way
- cleanups to Documenatation/ABI/ entries to make them parse easier
due to typos and other minor things
- default_attrs use for some ktype users
- driver model documentation file conversions to .rst
- compressed firmware file loading
- deferred probe fixes
All of these have been in linux-next for a while, with a bunch of
merge issues that Stephen has been patient with me for"
* tag 'driver-core-5.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (102 commits)
debugfs: make error message a bit more verbose
orangefs: fix build warning from debugfs cleanup patch
ubifs: fix build warning after debugfs cleanup patch
driver: core: Allow subsystems to continue deferring probe
drivers: base: cacheinfo: Ensure cpu hotplug work is done before Intel RDT
arch_topology: Remove error messages on out-of-memory conditions
lib: notifier-error-inject: no need to check return value of debugfs_create functions
swiotlb: no need to check return value of debugfs_create functions
ceph: no need to check return value of debugfs_create functions
sunrpc: no need to check return value of debugfs_create functions
ubifs: no need to check return value of debugfs_create functions
orangefs: no need to check return value of debugfs_create functions
nfsd: no need to check return value of debugfs_create functions
lib: 842: no need to check return value of debugfs_create functions
debugfs: provide pr_fmt() macro
debugfs: log errors when something goes wrong
drivers: s390/cio: Fix compilation warning about const qualifiers
drivers: Add generic helper to match by of_node
driver_find_device: Unify the match function with class_find_device()
bus_find_device: Unify the match callback with class_find_device
...
A smaller batch of fixes, nothing that stands out as risky or scary.
Mostly DTS tweaks for a few issues:
- GPU fixlets for Meson
- CPU idle fix for LS1028A
- PWM interrupt fixes for i.MX6UL
Also, enable a driver (FSL_EDMA) on arm64 defconfig, and a warning and
two MAINTAINER tweaks.
-----BEGIN PGP SIGNATURE-----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=Jr9u
-----END PGP SIGNATURE-----
Merge tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC fixes from Olof Johansson:
"A smaller batch of fixes, nothing that stands out as risky or scary.
Mostly DTS tweaks for a few issues:
- GPU fixlets for Meson
- CPU idle fix for LS1028A
- PWM interrupt fixes for i.MX6UL
Also, enable a driver (FSL_EDMA) on arm64 defconfig, and a warning and
two MAINTAINER tweaks"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc:
ARM: dts: imx6ul: fix PWM[1-4] interrupts
ARM: omap2: remove incorrect __init annotation
ARM: dts: gemini Fix up DNS-313 compatible string
ARM: dts: Blank D-Link DIR-685 console
arm64: defconfig: Enable FSL_EDMA driver
arm64: dts: ls1028a: Fix CPU idle fail.
MAINTAINERS: BCM53573: Add internal Broadcom mailing list
MAINTAINERS: BCM2835: Add internal Broadcom mailing list
ARM: dts: meson8b: fix the operating voltage of the Mali GPU
ARM: dts: meson8b: drop undocumented property from the Mali GPU node
ARM: dts: meson8: fix GPU interrupts and drop an undocumented property
OMAP2 depends on ARCH_MULTI_V6, which makes sure that the kernel is
compiled with -march=armv6. The compiler frontend will pass the
architecture to the assembler. There is no explicit architecture
specification necessary.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
The LLVM Target parser currently does not allow to specify the security
extension as part of -march (see also LLVM Bug 40186 [0]). When trying
to use Clang with LLVM's integrated assembler, this leads to build
errors such as this:
clang-8: error: the clang compiler does not support '-Wa,-march=armv7-a+sec'
Use ".arch_extension sec" to enable the security extension in a more
portable fasion. Also make sure to use ".arch armv7-a" in case a v6/v7
multi-platform kernel is being built.
Note that this is technically not exactly the same as the old code
checked for availabilty of the security extension by calling as-instr.
However, there are already other sites which use ".arch_extension sec"
unconditionally, hence de-facto we need an assembler capable of
".arch_extension sec" already today (arch/arm/mm/proc-v7.S). The
arch extension "sec" is available since binutils 2.21 according to
its documentation [1].
[0] https://bugs.llvm.org/show_bug.cgi?id=40186
[1] https://sourceware.org/binutils/docs-2.21/as/ARM-Options.html
Signed-off-by: Stefan Agner <stefan@agner.ch>
Acked-by: Mans Rullgard <mans@mansr.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Based on 2 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation #
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 4122 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Enrico Weigelt <info@metux.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190604081206.933168790@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation this program is
distributed in the hope that it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details you should have received a copy of the gnu general
public license along with this program if not see http www gnu org
licenses
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 503 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Enrico Weigelt <info@metux.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190602204653.811534538@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
omap3xxx_prm_enable_io_wakeup() is marked __init, but its caller is not, so
we get a warning with clang-8:
WARNING: vmlinux.o(.text+0x343c8): Section mismatch in reference from the function omap3xxx_prm_late_init() to the function .init.text:omap3xxx_prm_enable_io_wakeup()
The function omap3xxx_prm_late_init() references
the function __init omap3xxx_prm_enable_io_wakeup().
This is often because omap3xxx_prm_late_init lacks a __init
annotation or the annotation of omap3xxx_prm_enable_io_wakeup is wrong.
When building with gcc, omap3xxx_prm_enable_io_wakeup() is always
inlined, so we never noticed in the past.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Nathan Chancellor <natechancellor@gmail.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Just two changes to make few platform data functions static, and to
call dev_info() if am437x is suspending to RTC-only mode. We want to
see this in case of issues as it depends on the board wiring for things
like DDR memory.
-----BEGIN PGP SIGNATURE-----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=+Fzf
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v5.3/soc-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into arm/soc
ti-sysc soc changes for v5.3
Just two changes to make few platform data functions static, and to
call dev_info() if am437x is suspending to RTC-only mode. We want to
see this in case of issues as it depends on the board wiring for things
like DDR memory.
* tag 'omap-for-v5.3/soc-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
soc: ti: pm33xx: Add a print while entering RTC only mode with DDR in self-refresh
ARM: OMAP2+: Make some variables static
Signed-off-by: Olof Johansson <olof@lixom.net>
This series of changes improves probing devices with ti-sysc to the
point where we can now probe most devices without the custom dts
property "ti,hwmods" and no legacy platform data :)
We add support for platform data callbacks for idling and unidling the
clockdomain the module belongs to. The rest of the series mostly adds
handling for the various quirks needed by old legacy modules such as
i2c and watchdog. Some quirk handling is still missing for few modules,
but those will be added as they get tested.
The related platform data and dts changes will be sent separately.
-----BEGIN PGP SIGNATURE-----
iQJFBAABCAAvFiEEkgNvrZJU/QSQYIcQG9Q+yVyrpXMFAl0AuTURHHRvbnlAYXRv
bWlkZS5jb20ACgkQG9Q+yVyrpXPn4A//Z7uWk98dwcIs8/28CaFTPsRGhx3p+hj0
Mafl3eT5Q/y0TFGkMw3g5LSX5EZlz+5t6eFsolU+O8p6jsPoo5mcsGQfgkraydE3
x0wfSkFiqJcTP4FFvrwcekSQZGjpeZoUdQZ/e2epSDWvPx9gRzLFR3wCLPJ1MOgg
dveEJTnPfpFLliTZeVpcn4v2P4+KfBn4iu2ojr9qcLZL9QNFZr3NQLRdx6kUw7qf
b3eRugzx3sBA4pKLEfqrOzqjP77W9sy1zDN5rA3GNgo+b+OyBhdu/pxxkREP4t4+
8/1E/JndDVkO98ooFJ+MWdnh8HQmefEjyaoaYa7LN6438mivkOFPFAUMtuOdKzv/
FTa9r7xpo1Iq5b3HyE7NA+xZfoHKBEHzY0zbNyJLz75Ctnh3zOuHAA3xwxOlbgn+
UX/1DAS/7ALUXrXkk331VVzYX5UfOxrH2+CF2GF9vpCNZZ17Qp3ZKy4XW1Qv9nfy
nozOkqSvbGG0tzhq+wLd6Soo2Vns7CfHRqDB8txLeBGtrk/kahHsxe7dLo4+fHk6
DH0R7mZ6QnvaMWpJwkqoBUp7lD9ej9/pw2newbb5RyUDQqMjNvdY3zcBOeXeWulh
m2hWFKt1JTGTvXtbTjOOnfQIyICUClMzo4VowLBplfZELJvK781/5P3Jb4ZOFF0N
I1DN4vDxqMg=
=Fxul
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v5.3/ti-sysc-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into arm/drivers
ti-sysc interconnect target module driver changes for v5.3
This series of changes improves probing devices with ti-sysc to the
point where we can now probe most devices without the custom dts
property "ti,hwmods" and no legacy platform data :)
We add support for platform data callbacks for idling and unidling the
clockdomain the module belongs to. The rest of the series mostly adds
handling for the various quirks needed by old legacy modules such as
i2c and watchdog. Some quirk handling is still missing for few modules,
but those will be added as they get tested.
The related platform data and dts changes will be sent separately.
* tag 'omap-for-v5.3/ti-sysc-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
bus: ti-sysc: Add support for module specific reset quirks
bus: ti-sysc: Detect uarts also on omap34xx
bus: ti-sysc: Do rstctrl reset handling in two phases
bus: ti-sysc: Add support for disabling module without legacy mode
bus: ti-sysc: Set ENAWAKEUP if available
bus: ti-sysc: Handle swsup idle mode quirks
bus: ti-sysc: Handle clockactivity for enable and disable
bus: ti-sysc: Enable interconnect target module autoidle bit on enable
bus: ti-sysc: Allow QUIRK_LEGACY_IDLE even if legacy_mode is not set
bus: ti-sysc: Make OCP reset work for sysstatus and sysconfig reset bits
bus: ti-sysc: Support 16-bit writes too
bus: ti-sysc: Add support for missing clockdomain handling
ARM: dts: dra71x: Disable usb4_tm target module
ARM: dts: dra71x: Disable rtc target module
ARM: dts: dra76x: Disable usb4_tm target module
ARM: dts: dra76x: Disable rtc target module
ARM: dts: dra76x: Update MMC2_HS200_MANUAL1 iodelay values
ARM: dts: am57xx-idk: Remove support for voltage switching for SD card
bus: ti-sysc: Handle devices with no control registers
ARM: dts: Configure osc clock for d_can on am335x
Signed-off-by: Olof Johansson <olof@lixom.net>
Fix sparse warnings:
arch/arm/mach-omap2/omap_hwmod_33xx_43xx_ipblock_data.c:532:25: warning: symbol 'am33xx_gpio_hwmod_class' was not declared. Should it be static?
arch/arm/mach-omap2/omap_hwmod_33xx_43xx_ipblock_data.c:542:19: warning: symbol 'am33xx_gpio1_hwmod' was not declared. Should it be static?
arch/arm/mach-omap2/omap_hwmod_33xx_43xx_ipblock_data.c:562:19: warning: symbol 'am33xx_gpio2_hwmod' was not declared. Should it be static?
arch/arm/mach-omap2/omap_hwmod_33xx_43xx_ipblock_data.c:582:19: warning: symbol 'am33xx_gpio3_hwmod' was not declared. Should it be static?
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation this program is
distributed in the hope that it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details you should have received a copy of the gnu general
public license along with this program if not write to the free
software foundation inc 51 franklin st fifth floor boston ma 02110
1301 usa
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 246 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190530000436.674189849@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When calling debugfs functions, there is no need to ever check the
return value. The function can work or not, but the code logic should
never do something different based on this.
Cc: Kevin Hilman <khilman@kernel.org>
Cc: Russell King <linux@armlinux.org.uk>
Cc: linux-omap@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version this program is distributed in the
hope that it will be useful but without any warranty without even
the implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details you
should have received a copy of the gnu general public license along
with this program if not write to the free software foundation inc
59 temple place suite 330 boston ma 02111 1307 usa
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 1334 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070033.113240726@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 3029 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070032.746973796@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We need to let ti-sysc driver manage clockdomain autoidle for the
duration of of reset, enable and idle. And we need to do it before we
enable the clock and after we disable it. Currently we are still
relying on platform callbacks indirectly managing clockdomain autoidle.
But I noticed that for device tree only probed drivers it now happens
only after we enabling the clocks and before we disable the clocks,
while it should be the other way around. So far I have not noticed
any issues with this though.
Let's add new ti_sysc_clkdm_deny_idle() and ti_sysc_clkdm_allow_idle()
functions for ti-sysc driver to use to manage clockdomains directly via
platform data callbacks. Note that we can implement the clockdomain
functions in pdata-quirks.c as for probing devices without "ti,hwmods"
custom property we don't need to use the other platform data callbacks.
Let's do this in one patch as there's is still an unlikely chance we
may need to apply this as a fix for v5.2 for dropping legacy platform
data for some devices. We also do have the option of adding back the
platform data if needed in case of trouble.
Tested-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version author [hema] [hk] [hemahk]@[ti] [com]
this program is distributed in the hope that it will be useful but
without any warranty without even the implied warranty of
merchantability or fitness for a particular purpose see the gnu
general public license for more details you should have received a
copy of the gnu general public license along with this program if
not write to the free software foundation inc 675 mass ave cambridge
ma 02139 usa
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 1 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190523091649.791555110@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add SPDX license identifiers to all Make/Kconfig files which:
- Have no license information of any form
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jianping Liu