Sync code to the same with tk4 pub/lts/0017-kabi, except deleted rue
and wujing. Partners can submit pull requests to this branch, and we
can pick the commits to tk4 pub/lts/0017-kabi easly.
Signed-off-by: Jianping Liu <frankjpliu@tencent.com>
ARCH_BRCMSTB needs to use the BCM2835 pin controller for chips like
BCM7211 which adopted that pin controller for GPIO.
Signed-off-by: Doug Berger <opendmb@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Allow the use of reset controllers on ARCH_BRCMSTB such as the
recently introduced RESET_BRCMSTB driver.
Signed-off-by: Jim Quinlan <jim2101024@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
The PM block that the wdt driver was binding to actually has multiple
features we want to expose (power domains, reset, watchdog). Move the
DT attachment to a MFD driver and make WDT probe against MFD.
Signed-off-by: Eric Anholt <eric@anholt.net>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
SoC updates, mostly refactorings and cleanups of old legacy platforms,
but also a few more things:
New SoC support this release:
- NXP/Freescale i.MX7ULP (1x Cortex-A7, Cortex-M4, graphics, etc)
- Allwinner F1C100, older platform with an ARM926-EJS (ARMv5) core
Cleanups of various platforms:
- OMAP1 ams-delta does some GPIO cleanups
- Davinci removes of at24 platform data
- Samsung cleans up old wakeup, PM debug and secondary core boot code
- Renesas moves around config options and PM code to drivers/soc for
sharing with 64-bit and more consistency
- i.MX, Broadcom and SoCFPGA all have tweaks to lowlevel debug console setups
- SoCFPGA adds explicit selection of ARM errata and removes some unused code
This tag also contains a few patches that I had queued up as fixes for
4.20 but didn't send in before the release.
-----BEGIN PGP SIGNATURE-----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=m7me
-----END PGP SIGNATURE-----
Merge tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull arm SoC platform updates from Olof Johansson:
"SoC updates, mostly refactorings and cleanups of old legacy platforms,
but also a few more things:
New SoC support this release:
- NXP/Freescale i.MX7ULP (1x Cortex-A7, Cortex-M4, graphics, etc)
- Allwinner F1C100, older platform with an ARM926-EJS (ARMv5) core
Cleanups of various platforms:
- OMAP1 ams-delta does some GPIO cleanups
- Davinci removes of at24 platform data
- Samsung cleans up old wakeup, PM debug and secondary core boot code
- Renesas moves around config options and PM code to drivers/soc for
sharing with 64-bit and more consistency
- i.MX, Broadcom and SoCFPGA all have tweaks to lowlevel debug
console setups
- SoCFPGA adds explicit selection of ARM errata and removes some
unused code
This also contains a few patches that I had queued up as fixes for
4.20 but didn't send in before the release"
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (68 commits)
arm64: dts: renesas: draak: Fix CVBS input
ARM: omap2: avoid section mismatch warning
ARM: tegra: avoid section mismatch warning
ARM: ks8695: fix section mismatch warning
ARM: pxa: avoid section mismatch warning
ARM: mmp: fix pxa168_device_usb_phy use on aspenite
ARM: mmp: fix timer_init calls
ARM: OMAP1: fix USB configuration for device-only setups
ARM: OMAP1: add MMC configuration for Palm Tungsten E
ARM: imx: fix dependencies on imx7ulp
ARM: meson: select HAVE_ARM_TWD and ARM_GLOBAL_TIMER
MAINTAINERS: add drivers/soc/amlogic/ to amlogic list
ARM: imx: add initial support for imx7ulp
ARM: debug-imx: only define DEBUG_IMX_UART_PORT if needed
ARM: dts: Fix OMAP4430 SDP Ethernet startup
ARM: dts: am335x-pdu001: Fix polarity of card detection input
ARM: OMAP1: ams-delta: Fix audio permanently muted
ARM: dts: omap5: Fix dual-role mode on Super-Speed port
arm64: dts: rockchip: fix rk3399-rockpro64 regulator gpios
ARM: davinci: da850-evm: remove unnecessary include
...
Move the definitions to drivers/pci and let the architectures select
them. Two small differences to before: PCI_DOMAINS_GENERIC now selects
PCI_DOMAINS, cutting down the churn for modern architectures. As the
only architectured arm did previously also offer PCI_DOMAINS as a user
visible choice in addition to selecting it from the relevant configs,
this is gone now.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Paul Burton <paul.burton@mips.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Allow BCM63xx to compile support for reset controllers since we will
require a specific reset controller to release resets for on-chip
peripherals.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Commit 51bc085d64 ("PCI: Improve host drivers compile test coverage")
added configuration options to allow PCI host controller drivers to be
compile tested on all architectures.
Some host controller drivers (eg PCIE_ALTERA) config entries select the
PCI_DOMAINS config option to enable PCI domains management in the kernel.
Now that host controller drivers can be compiled on all architectures, this
triggers build regressions on arches that do not implement the PCI_DOMAINS
required API (ie pci_domain_nr()):
drivers/ata/pata_ali.c: In function 'ali_init_chipset':
drivers/ata/pata_ali.c:469:38: error: implicit declaration of function 'pci_domain_nr'; did you mean 'pci_iomap_wc'?
Furthemore, some software configurations (ie Jailhouse) require a
PCI_DOMAINS enabled kernel to configure multiple host controllers without
having an explicit dependency on the ARM platform on which they run.
Make PCI_DOMAINS a visible configuration option on ARM so that software
configurations that need it can manually select it and move the PCI_DOMAINS
selection from PCI controllers configuration file to ARM sub-arch config
entries that currently require it, fixing the issue.
Fixes: 51bc085d64 ("PCI: Improve host drivers compile test coverage")
Link: https://lkml.kernel.org/r/20180612170229.GA10141@roeck-us.net
Reported-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <helgaas@kernel.org>
Acked-by: Jan Kiszka <jan.kiszka@siemens.com>
Acked-by: Ley Foon Tan <ley.foon.tan@intel.com>
Acked-by: Rob Herring <robh@kernel.org>
Cc: Scott Branden <scott.branden@broadcom.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Guenter Roeck <linux@roeck-us.net>
Define this symbol if the architecture either uses 64-bit pointers or the
PHYS_ADDR_T_64BIT is set. This covers 95% of the old arch magic. We only
need an additional select for Xen on ARM (why anyway?), and we now always
set ARCH_DMA_ADDR_T_64BIT on mips boards with 64-bit physical addressing
instead of only doing it when highmem is set.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: James Hogan <jhogan@kernel.org>
Most of the commits are for defconfig changes, to enable newly added
drivers or features that people have started using. For the changed
lines lines, we have mostly cleanups, the affected platforms are
OMAP, Versatile, EP93xx, Samsung, Broadcom, i.MX, and Actions.
The largest single change is the introduction of the TI "sysc" bus
driver, with the intention of cleaning up more legacy code.
Two new SoC platforms get added this time:
- Allwinner R40 is a modernized version of the A20 chip, now
with a Quad-Core ARM Cortex-A7. According to the manufacturer,
it is intended for "Smart Hardware"
- Broadcom Hurricane 2 (Aka Strataconnect BCM5334X) is a family
of chips meant for managed gigabit ethernet switches, based
around a Cortex-A9 CPU.
Finally, we gain SMP support for two platforms: Renesas R-Car E2
and Amlogic Meson8/8b, which were previously added but only supported
uniprocessor operation.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=jlJ2
-----END PGP SIGNATURE-----
Merge tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC platform updates from Arnd Bergmann:
"Most of the commits are for defconfig changes, to enable newly added
drivers or features that people have started using. For the changed
lines lines, we have mostly cleanups, the affected platforms are OMAP,
Versatile, EP93xx, Samsung, Broadcom, i.MX, and Actions.
The largest single change is the introduction of the TI "sysc" bus
driver, with the intention of cleaning up more legacy code.
Two new SoC platforms get added this time:
- Allwinner R40 is a modernized version of the A20 chip, now with a
Quad-Core ARM Cortex-A7. According to the manufacturer, it is
intended for "Smart Hardware"
- Broadcom Hurricane 2 (Aka Strataconnect BCM5334X) is a family of
chips meant for managed gigabit ethernet switches, based around a
Cortex-A9 CPU.
Finally, we gain SMP support for two platforms: Renesas R-Car E2 and
Amlogic Meson8/8b, which were previously added but only supported
uniprocessor operation"
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (118 commits)
ARM: multi_v7_defconfig: Select RPMSG_VIRTIO as module
ARM: multi_v7_defconfig: enable CONFIG_GPIO_UNIPHIER
arm64: defconfig: enable CONFIG_GPIO_UNIPHIER
ARM: meson: enable MESON_IRQ_GPIO in Kconfig for meson8b
ARM: meson: Add SMP bringup code for Meson8 and Meson8b
ARM: smp_scu: allow the platform code to read the SCU CPU status
ARM: smp_scu: add a helper for powering on a specific CPU
dt-bindings: Amlogic: Add Meson8 and Meson8b SMP related documentation
ARM: OMAP3: Delete an unnecessary variable initialisation in omap3xxx_hwmod_init()
ARM: OMAP3: Use common error handling code in omap3xxx_hwmod_init()
ARM: defconfig: select the right SX150X driver
arm64: defconfig: Enable QCOM_IOMMU
arm64: Add ThunderX drivers to defconfig
arm64: defconfig: Enable Tegra PCI controller
cpufreq: imx6q: Move speed grading check to cpufreq driver
arm64: defconfig: re-enable Qualcomm DB410c USB
ARM: configs: stm32: Add MDMA support in STM32 defconfig
ARM: imx: Enable cpuidle for i.MX6DL starting at 1.1
bus: ti-sysc: Fix unbalanced pm_runtime_enable by adding remove
bus: ti-sysc: mark PM functions as __maybe_unused
...
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add a Kconfig entry point and basic machine board code for the Broadcom
Hurricane 2 SoCs used in switching products.
Acked-by: Jon Mason <jon.mason@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
This patch fixes some spelling typos found in Kconfig files.
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
SoC platform changes (arch/arm/mach-*). This merge window, the bulk is
for a few platforms:
- Andres Färber adds initial support for the Actions Semi S500 (a.k.a.
'owl') platform, a close relative of the S900 platform he adds for arm64.
- in mach-omap2, we remove more legacy code
- Rockchips gains support for the RV1108 SoC designed for camera
applications.
- For Atmel, we gain support for MMU-less SoCs (SAME70/V71/S70/V70)
- Minor updates for other platforms, including davinci, s3c64xx,
prima2, stm32, broadcom nsp, amlogic, pxa, imx and renesas
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=8F3w
-----END PGP SIGNATURE-----
Merge tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC platform updates from Arnd Bergmann:
"SoC platform changes (arch/arm/mach-*). This merge window, the bulk is
for a few platforms:
- Andres Färber adds initial support for the Actions Semi S500 (aka
'owl') platform, a close relative of the S900 platform he adds for
arm64.
- in mach-omap2, we remove more legacy code
- Rockchips gains support for the RV1108 SoC designed for camera
applications.
- For Atmel, we gain support for MMU-less SoCs (SAME70/V71/S70/V70)
- Minor updates for other platforms, including davinci, s3c64xx,
prima2, stm32, broadcom nsp, amlogic, pxa, imx and renesas"
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (74 commits)
ARM: owl: smp: Drop bogus holding pen
ARM: owl: Drop custom machine
ARM: owl: smp: Implement SPS power-gating for CPU2 and CPU3
soc: actions: owl-sps: Factor out owl_sps_set_pg() for power-gating
soc: actions: Add Owl SPS
dt-bindings: power: Add Owl SPS power domains
MAINTAINERS: Update Actions Semi section with SPS
ARM: owl: Implement CPU enable-method for S500
MAINTAINERS: Add Actions Semi Owl section
ARM: Prepare Actions Semi S500
ARM: socfpga: Increase max number of GPIOs
ARM: stm32: Introduce MACH_STM32F469 flag
ARM: prima2: remove redundant select CPU_V7
ARM: davinci: fix const warnings
ARM: shmobile: pm-rmobile: Use GENPD_FLAG_ALWAYS_ON
ARM: OMAP4: hwmod_data: add SHAM crypto accelerator
ARM: OMAP4: hwmod data: add des
ARM: OMAP4: hwmod data: add aes2
ARM: OMAP4: hwmod data: add aes1
ARM: pxa: Delete an error message for a failed memory allocation in pxa3xx_u2d_probe()
...
The config option name is now renamed to 'TIMER_OF' for consistency with
the CLOCKSOURCE_OF_DECLARE => TIMER_OF_DECLARE change.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Change the Northstar Plus Kconfig to select THERMAL and THERMAL_OF,
which allows the ns-thermal driver to be selected via menuconfig.
Signed-off-by: Jon Mason <jon.mason@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Due to the brcmstb SoC's memory map, we may have holes in the memory if
we don't populate the maximum amount of memory supported by e.g: the
first memory controller which spans either the first 1GiB or first 2GiB
of memory.
We need to select ARCH_HAS_HOLES_MEMORYMODEL in order to enable
CONFIG_HAVE_ARCH_PFN_VALID on platforms that have CONFIG_SPARSEMEM
enabled.
Signed-off-by: Danesh Petigara <danesh.petigara@broadcom.com>
[florian: Detailed commit message]
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Some Host Controller hardware blocks, like the OHCI, EHCI and SDIO
controllers, have hardware blocks that are not capable of doing 64 bit
DMA. These host controllers fail on boards with >3GB of memory because
the memory above 3GB is located physically >= 0x100000000 and can only
be accessed using 64 DMA. The way Linux is currently configured for
BRCMSTB systems, the memory given to drivers for DMA through functions
like dma_alloc_coherent() comes from CMA memory and CMA memory is taken
from the top of physical memory. When these drivers get a DMA buffer
with an address >=0x100000000, they end up dropping the upper 32 bit of
the address causing the hardware to DMA to incorrect memory, typically
BMEM (custom memory carveout). This issue was discovered on a
BCM97449SSV_DDR4 system with 4GB or memory.
The fix is to enable CONFIG_ZONE_DMA. On ARM systems this makes sure
that all DMA memory is located within the first 32 bits of address
space.
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
These are updates for platform specific code on 32-bit ARM machines,
essentially anything that can not (yet) be expressed using DT files.
Noteworthy changes include:
- We get support for running in big-endian mode on two platforms:
sunxi (Allwinner) and s3c24xx (old Samsung).
- The recently added Uniphier platform now uses standard PSCI
methods for SMP booting and we remove support for old bootloader
versions that did not support it yet.
- In sunxi, we gain support for the "Nextthing GR8" SoC, which
is a close relative of the Allwinner A13 and R8 chips.
- PXA completes its move over to the generic dmaengine framework
and removes its old private API
- mach-bcm gains support for BCM47189/BCM53573, their first ARM
SoC with integrated 802.11ac wireless networking.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=y4XF
-----END PGP SIGNATURE-----
Merge tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC platform updates from Arnd Bergmann:
"These are updates for platform specific code on 32-bit ARM machines,
essentially anything that can not (yet) be expressed using DT files.
Noteworthy changes include:
- We get support for running in big-endian mode on two platforms:
sunxi (Allwinner) and s3c24xx (old Samsung).
- The recently added Uniphier platform now uses standard PSCI methods
for SMP booting and we remove support for old bootloader versions
that did not support it yet.
- In sunxi, we gain support for the "Nextthing GR8" SoC, which is a
close relative of the Allwinner A13 and R8 chips.
- PXA completes its move over to the generic dmaengine framework and
removes its old private API
- mach-bcm gains support for BCM47189/BCM53573, their first ARM SoC
with integrated 802.11ac wireless networking"
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (54 commits)
ARM: imx legacy: pca100: move peripheral initialization to .init_late
ARM: imx legacy: mx27ads: move peripheral initialization to .init_late
ARM: imx legacy: mx21ads: move peripheral initialization to .init_late
ARM: imx legacy: pcm043: move peripheral initialization to .init_late
ARM: imx legacy: mx35-3ds: move peripheral initialization to .init_late
ARM: imx legacy: mx27-3ds: move peripheral initialization to .init_late
ARM: imx legacy: imx27-visstrim-m10: move peripheral initialization to .init_late
ARM: imx legacy: vpr200: move peripheral initialization to .init_late
ARM: imx legacy: mx31moboard: move peripheral initialization to .init_late
ARM: imx legacy: armadillo5x0: move peripheral initialization to .init_late
ARM: imx legacy: qong: move peripheral initialization to .init_late
ARM: imx legacy: mx31-3ds: move peripheral initialization to .init_late
ARM: imx legacy: pcm037: move peripheral initialization to .init_late
ARM: imx legacy: mx31lilly: move peripheral initialization to .init_late
ARM: imx legacy: mx31ads: move peripheral initialization to .init_late
ARM: imx legacy: mx31lite: move peripheral initialization to .init_late
ARM: imx legacy: kzm: move peripheral initialization to .init_late
MAINTAINERS: update list of Oxnas maintainers
ARM: orion5x: remove extraneous NO_IRQ
ARM: orion: simplify orion_ge00_switch_init
...
Make the clocks visible options that can be selected by anyone. This
avoids the problems of:
1) Select is a reverse dependency and is hard for people to understand
and can sometimes be a pain to track down
2) Build coverage goes down because configs are hidden
3) Code bloat
Patch suggested by Stephen Boyd
Signed-off-by: Jon Mason <jonmason@broadcom.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
BCM53573 series is a new family with embedded wireless. By marketing
people it's sometimes called Northstar but it uses different CPU and has
different architecture so we need a new symbol for it.
Fortunately it shares some peripherals with other iProc based SoCs so we
will be able to reuse some drivers/bindings.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Jon Mason <jon.mason@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
The cleanup branch keeps going down in size as we've completed a lot of
the major legacy platform removals and conversions.
A handful of changes this time around, some of the themes or larger sets are:
- A bunch of i.MX cleanups around platform detection, init call cleanups
- Misc fixes of missing/implicit includes
- Removal of ARCH_[WANT_OPTIONAL|REQUIRE]_GPIOLIB
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=SfR/
-----END PGP SIGNATURE-----
Merge tag 'armsoc-cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC cleanups from Olof Johansson:
"The cleanup branch keeps going down in size as we've completed a lot
of the major legacy platform removals and conversions.
A handful of changes this time around, some of the themes or larger
sets are:
- A bunch of i.MX cleanups around platform detection, init call cleanups
- Misc fixes of missing/implicit includes
- Removal of ARCH_[WANT_OPTIONAL|REQUIRE]_GPIOLIB"
* tag 'armsoc-cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (40 commits)
ARM: mps2: fix typo
ARM: s3c64xx: avoid warning about 'struct device_node'
bus: mvebu-mbus: make mvebu_mbus_syscore_ops static
bus: mvebu-mbus: fix __iomem on register pointers
ARM: tegra: Remove board_init_funcs array
ARM: iop: Fix indentation
ARM: imx: remove cpu_is_mx*()
ARM: imx: remove last call to cpu_is_mx5*
ARM: imx: rework mx27_pm_init() call
ARM: imx: deconstruct mx3_idle
ARM: imx: deconstruct mxc_rnga initialization
ARM: imx: remove cpu_is_mx1 check
ARM: i.MX: Do not explicitly call l2x0_of_init()
ARM: i.MX: system.c: Tweak prefetch settings for performance
ARM: i.MX: system.c: Replace magic numbers
ARM: i.MX: system.c: Remove redundant errata 752271 code
ARM: i.MX: system.c: Convert goto to if statement
ARM: Kirkwood: fix kirkwood_pm_init() declaration/type
ARM: Kirkwood: make kirkwood_disable_mbus_error_propagation() static
ARM: orion5x: make orion5x_legacy_handle_irq static
...
* commit '5c34a4e89c743339f78cafb2f2a826a010f0746a':
ARM: do away with ARCH_[WANT_OPTIONAL|REQUIRE]_GPIOLIB
ARM: uniphier: drop code for old DT binding
These cause a harmless conflict with the clps711x multiplatform
support, and it's easy to resolve.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Change the Kconfig option logic to fullfil with the current approach.
A new Kconfig option is added, CONFIG_BCM_KONA_TIMER and is selected by the
platform. Then the clocksource's Kconfig is changed to make this option
selectable by the user if the COMPILE_TEST option is set. Otherwise, it is
up to the platform's Kconfig to select the timer.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Change the Kconfig option logic to fullfil with the current approach.
A new Kconfig option is added, CONFIG_BCM2835_TIMER and is selected by the
platform. Then the clocksource's Kconfig is changed to make this option
selectable by the user if the COMPILE_TEST option is set. Otherwise, it
is up to the platform's Kconfig to select the timer.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
BCM23550 is a quad-A7 SoC used on the Broadcom "Sparrow" board.
It shares many IP blocks with other Broadcom Kona chips.
Signed-off-by: Chris Brand <chris.brand@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
This replaces:
- "select ARCH_REQUIRE_GPIOLIB" with "select GPIOLIB" as this can
now be selected directly.
- "select ARCH_WANT_OPTIONAL_GPIOLIB" with no dependency: GPIOLIB
is now selectable by everyone, so we need not declare our
intent to select it.
When ordering the symbols the following rationale was used:
if the selects were in alphabetical order, I moved select GPIOLIB
to be in alphabetical order, but if the selects were not
maintained in alphabetical order, I just replaced
"select ARCH_REQUIRE_GPIOLIB" with "select GPIOLIB".
Cc: Michael Büsch <m@bues.ch>
Cc: arm@kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Do not have the machine Kconfig entry point need to select
BRCMSTB_GISB_ARB, instead, just let it be default ARCH_BRCMSTB which is
a better way to deal with this. While at it, also make it default
BMIPS_GENERIC so the legacy MIPS-based STB platforms can benefit from
the same thing.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Value of soc_dev_attributes:
* family = chip family id
* soc_id = product id
* revision = product revision
Signed-off-by: Justin Chen <justin.chen@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Merge "BCM2835 SOC changes for 4.5" from Eric Anholt:
This pull request includes the bcm2835 changes for 4.5 targeting the
arm-soc next/soc branch.
* tag 'bcm2835-soc-next-2015-12-28' of http://github.com/anholt/linux:
ARM: bcm2835: Add Kconfig support for bcm2836
ARM: bcm2835: Add a compat string for bcm2836 machine probe
dt-bindings: Add root properties for Raspberry Pi 2
Conflicts:
arch/arm/mach-bcm/Kconfig
Merge in cleanup to avoid internal conflicts with newly added code.
* treewide/cleanup:
ARM: use "depends on" for SoC configs instead of "if" after prompt
ARM/clocksource: use automatic DT probing for ux500 PRCMU
ARM: use const and __initconst for smp_operations
ARM: hisi: do not export smp_operations structures
Signed-off-by: Olof Johansson <olof@lixom.net>
Add SMP support for Broadcom's Northstar Plus SoC
cpu enable method. This changes also consolidates
iProc family's - BCM NSP and BCM Kona, platform
SMP handling in a common file.
Northstar Plus SoC is based on ARM Cortex-A9
revision r3p0 which requires configuration for ARM
Errata 764369 for SMP. This change adds the needed
configuration option.
Signed-off-by: Kapil Hali <kapilh@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Many ARM sub-architectures use prompts followed by "if" conditional,
but it is wrong.
Please notice the difference between
config ARCH_FOO
bool "Foo SoCs" if ARCH_MULTI_V7
and
config ARCH_FOO
bool "Foo SoCs"
depends on ARCH_MULTI_V7
These two are *not* equivalent!
In the former statement, it is not ARCH_FOO, but its prompt that
depends on ARCH_MULTI_V7. So, it is completely valid that ARCH_FOO
is selected by another, but ARCH_MULTI_V7 is still disabled. As it is
not unmet dependency, Kconfig never warns. This is probably not what
you want.
The former should be used only when you need to do so, and you really
understand what you are doing. (In most cases, it should be wrong!)
For enabling/disabling sub-architectures, the latter is always correct.
As a good side effect, this commit fixes some entries over 80 columns
(mach-imx, mach-integrator, mach-mbevu).
[Arnd: I note that there is not really a bug here, according to
the discussion that followed, but I can see value in being consistent
and in making the lines shorter]
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
Acked-by: Liviu Dudau <Liviu.Dudau@arm.com>
Acked-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Jun Nie <jun.nie@linaro.org>
Acked-by: Matthias Brugger <matthias.bgg@gmail.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Acked-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Acked-by: Krzysztof Halasa <khc@piap.pl>
Acked-by: Maxime Coquelin <maxime.coquelin@st.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The BCM4708 I have, which is probably the first generation which got
to the consumer market, is using a ARM Cortex-A9 rev r3p0 and a
L2C-310 rev r3p2 L2 cache controller. There are 3 workarounds for known
erratas in the Linux kernel which could be activated and will be in
this patch. There are currently no workarounds which have to be
activated for the L2C-310 rev r3p2 in Linux.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
New and/or improved SoC support for this release:
- Marvell Berlin:
* Enable standard DT-based cpufreq
* Add CPU hotplug support
- Freescale:
* Ethernet init for i.MX7D
* Suspend/resume support for i.MX6UL
- Allwinner:
* Support for R8 chipset (used on NTC's $9 C.H.I.P board)
- Mediatek:
* SMP support for some platforms
- Uniphier:
* L2 support
* Cleaned up SMP support, etc.
+ A handful of other patches around above functionality, and a few other
smaller changes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=h5xk
-----END PGP SIGNATURE-----
Merge tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC platform updates from Olof Johansson:
"New and/or improved SoC support for this release:
Marvell Berlin:
- Enable standard DT-based cpufreq
- Add CPU hotplug support
Freescale:
- Ethernet init for i.MX7D
- Suspend/resume support for i.MX6UL
Allwinner:
- Support for R8 chipset (used on NTC's $9 C.H.I.P board)
Mediatek:
- SMP support for some platforms
Uniphier:
- L2 support
- Cleaned up SMP support, etc.
plus a handful of other patches around above functionality, and a few
other smaller changes"
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (42 commits)
ARM: uniphier: rework SMP operations to use trampoline code
ARM: uniphier: add outer cache support
Documentation: EXYNOS: Update bootloader interface on exynos542x
ARM: mvebu: add broken-idle option
ARM: orion5x: use mac_pton() helper
ARM: at91: pm: at91_pm_suspend_in_sram() must be 8-byte aligned
ARM: sunxi: Add R8 support
ARM: digicolor: select pinctrl/gpio driver
arm: berlin: add CPU hotplug support
arm: berlin: use non-self-cleared reset register to reset cpu
ARM: mediatek: add smp bringup code
ARM: mediatek: enable gpt6 on boot up to make arch timer working
soc: mediatek: Fix random hang up issue while kernel init
soc: ti: qmss: make acc queue support optional in the driver
soc: ti: add firmware file name as part of the driver
Documentation: dt: soc: Add description for knav qmss driver
ARM: S3C64XX: Use PWM lookup table for mach-smartq
ARM: S3C64XX: Use PWM lookup table for mach-hmt
ARM: S3C64XX: Use PWM lookup table for mach-crag6410
ARM: S3C64XX: Use PWM lookup table for smdk6410
...
When CONFIG_CYGNUS is set but CONFIG_COMMON_CLK_IPROC is disabled, the
following link failures are caused:
drivers/built-in.o: In function `cygnus_armpll_init':
:(.init.text+0x1d290): undefined reference to `iproc_armpll_setup'
drivers/built-in.o: In function `cygnus_genpll_clk_init':
:(.init.text+0x1d2c4): undefined reference to `iproc_pll_clk_setup'
drivers/built-in.o: In function `cygnus_lcpll0_clk_init':
:(.init.text+0x1d304): undefined reference to `iproc_pll_clk_setup'
drivers/built-in.o: In function `cygnus_mipipll_clk_init':
:(.init.text+0x1d344): undefined reference to `iproc_pll_clk_setup'
drivers/built-in.o: In function `cygnus_asiu_init':
:(.init.text+0x1d370): undefined reference to `iproc_asiu_setup'
It is fixed it by always selecting COMMON_CLK_IPROC from
ARCH_BCM_IPROC, and making COMMON_CLK_IPROC a silent option (thus
preventing it from being erroneously disabled by a user).
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jon Mason <jonmason@broadcom.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Broadcom Northstar Plus family of SoCs are used for switching
control and management applications as well as residential
router/gateway applications. The SoC features dual core Cortex
A9 ARM CPUs, integrating several peripheral interfaces including
multiple Gigabit Ethernet PHYs, DDR3 memory, PCIE Gen-2, USB 2.0
and USB 3.0, serial and NAND flash, SATA and several other IO
controllers.
Signed-off-by: Kapil Hali <kapilh@broadcom.com>
Signed-off-by: Jon Mason <jonmason@broadcom.com>
Acked-by: Scott Branden <sbranden@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Broadcom STB (BRCMSTB) has some 64-bit capable DMA and therefore needs
dma_addr_t to be a 64-bit size. One user is the Broadcom SATA3 AHCI
controller driver.
Signed-off-by: Gregory Fong <gregory.0xf0@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
This reverts 7dc95b40f5 ("ARM: BCM: Enable
NAND support for iProc SoCs") since it creates an unmet dependency for
MTD_NAND_BRCMNAND which depends on MTD and MTD_NAND, this results in the
following build failure for brcmnand:
LD init/built-in.o
drivers/built-in.o: In function `brcmnand_remove':
/home/fainelli/dev/linux/drivers/mtd/nand/brcmnand/brcmnand.c:2234:
undefined reference to `nand_release'
drivers/built-in.o: In function `brcmnand_init_cs':
/home/fainelli/dev/linux/drivers/mtd/nand/brcmnand/brcmnand.c:1933:
undefined reference to `nand_scan_ident'
/home/fainelli/dev/linux/drivers/mtd/nand/brcmnand/brcmnand.c:1958:
undefined reference to `nand_scan_tail'
Makefile:931: recipe for target 'vmlinux' failed
make: *** [vmlinux] Error 1
Instead, select this driver an all dependencies on the
multi_v7_defconfig.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Kevin Hilman <khilman@linaro.org>
Select ARCH_WANT_OPTIONAL_GPIOLIB from BRCMSTB to allow GPIOLIB and
GPIO_BRCMSTB to be enabled.
Signed-off-by: Gregory Fong <gregory.0xf0@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
A recent cleanup rearranged the Kconfig file for mach-bcm and
accidentally dropped the dependency on ARCH_MULTI_V7, which
makes it possible to now build the two mobile SoC platforms
on an ARMv6-only kernel, resulting in a log of Kconfig
warnings like
warning: ARCH_BCM_MOBILE selects ARM_ERRATA_775420 which has unmet direct dependencies (CPU_V7)
and which of course cannot work on any machine.
This puts back the dependencies as before.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 64e74aa788 ("ARM: mach-bcm: ARCH_BCM_MOBILE: remove one level of menu from Kconfig")
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Scott Branden <sbranden@broadcom.com>
Pull irq core updates from Thomas Gleixner:
"This is the first (boring) part of irq updates:
- support for big endian I/O accessors in the generic irq chip
- cleanup of brcmstb/bcm7120 drivers so they can be reused for non
ARM SoCs
- the usual pile of fixes and updates for the various ARM irq chips"
* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (25 commits)
irqchip: dw-apb-ictl: Add PM support
irqchip: dw-apb-ictl: Enable IRQ_GC_MASK_CACHE_PER_TYPE
irqchip: dw-apb-ictl: Always use use {readl|writel}_relaxed
ARM: orion: convert the irq_reg_{readl,writel} calls to the new API
irqchip: atmel-aic: Add missing entry for rm9200 irq fixups
irqchip: atmel-aic: Rename at91sam9_aic_irq_fixup for naming consistency
irqchip: atmel-aic: Add specific irq fixup function for sam9g45 and sam9rl
irqchip: atmel-aic: Add irq fixups for at91sam926x SoCs
irqchip: atmel-aic: Add irq fixup for RTT block
irqchip: brcmstb-l2: Convert driver to use irq_reg_{readl,writel}
irqchip: bcm7120-l2: Convert driver to use irq_reg_{readl,writel}
irqchip: bcm7120-l2: Decouple driver from brcmstb-l2
irqchip: bcm7120-l2: Extend driver to support 64+ bit controllers
irqchip: bcm7120-l2: Use gc->mask_cache to simplify suspend/resume functions
irqchip: bcm7120-l2: Fix missing nibble in gc->unused mask
irqchip: bcm7120-l2: Make sure all register accesses use base+offset
irqchip: bcm7120-l2, brcmstb-l2: Remove ARM Kconfig dependency
irqchip: bcm7120-l2: Eliminate bad IRQ check
irqchip: brcmstb-l2: Eliminate dependency on ARM code
genirq: Generic chip: Add big endian I/O accessors
...
Pull "Broadcom Cygnus SoC platform support" from Florian Fainelli:
This pull request contains the platform code to support the Broadcom Cygnus SoC
using the iProc architecture:
- add support for the Broadcom Cygnus SoC
- consolidate the BCM5301X Kconfig options under the iProc menuconfig entry
- remove one level of menu in menuconfig
* tag 'arm-soc/for-3.19/cygnus-platform-v2' of http://github.com/brcm/linux:
ARM: mach-bcm: ARCH_BCM_MOBILE: remove one level of menu from Kconfig
ARM: mach-bcm: Consolidate currently supported IPROC SoCs
ARM: cygnus: Initial support for Broadcom Cygnus SoC
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Jianping Liu