ARC linux uses 2 distribution modes for common interrupts: round robin
mode (IDU_M_DISTRI_RR) and a simple destination mode (IDU_M_DISTRI_DEST).
The first one is used when more than 1 cores may handle a common interrupt
and the second one is used when only 1 core may handle a common interrupt.
However idu_irq_set_affinity() always sets IDU_M_DISTRI_RR for all affinity
values. But there is no sense in setting of such mode if only 1 core must
handle a common interrupt.
Signed-off-by: Yuriy Kolerov <yuriy.kolerov@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
This came up when reviewing code to address missing IRQ affinity
setting in AXS103 platform and/or implementing hierarchical IRQ domains
- smp_ipi_irq_setup() callers pass hwirq but in turn calls
request_percpu_irq() which expects a linux virq. So invoke
irq_find_mapping() to do the conversion
(also explicitify this in code by renaming the args appropriately)
- idu_of_init()/idu_cascade_isr() were similarly using linux virq where
hwirq is expected, so do the conversion using irqd_to_hwirq() helper
Signed-off-by: Yuriy Kolerov <yuriy.kolerov@synopsys.com>
[vgupta: made changelog a bit concise a bit]
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
For CONFIG_SERIAL_EARLYCON we need 800MHz for NPS SoC
The early console driver uses BASE_BAUD and not using dtb.
The default of 50MHz is NOT good for NPS SoC.
Signed-off-by: Noam Camus <noamca@mellanox.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
The current code doesn't even compile as somehow the inline assembly
can't see the register names defined as ARC_RTC_*
I'm pretty sure It worked when I first got it merged, but the tools were
definitely different then.
So better to write this in "C" anyways.
CC: stable@vger.kernel.org #4.2+
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
The original syscall only used to return errno to indicate if cmpxchg
succeeded. It was not returning the "previous" value which typical cmpxchg
callers are interested in to build their slowpaths or retry loops.
Given user preemption in syscall return path etc, it is not wise to
check this in userspace afterwards, but should be what kernel actually
observed in the syscall.
So change the syscall interface to always return the previous value and
additionally set Z flag to indicate whether operation succeeded or not
(just like ARM implementation when they used to have this syscall)
The flag approach avoids having to put_user errno which is nice given
the use case for this syscall cares mostly about the "previous" value.
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
At smp_prepare_cpus() we set present cpu mask as part of init
for all CPUs at range [0-max_cpus].
This is done without checking if this mask is already being set.
At platform of eznps this mask is already being initialized at
smp_init_cpus() by using hook plat_smp_ops.init_early_smp().
So to avoid overriding of present cpu mask we check the number of
bits which are set in this mask. At the begin only bit for boot CPU
is set so if number of bits already set is no more than one we can be
assure that there is no overriding of this mask.
Signed-off-by: Noam Camus <noamca@mellanox.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Now that we have referece to section name string table in
apply_relocate_add(), use it to
- print the name of section being relocated
- print symbol with NULL name (since it refers to a section)
before
| Section to fixup 7000a060
| =========================================================
| rela->r_off | rela->addend | sym->st_value | ADDR | VALUE
| =========================================================
| 1c 0 7000e000 7000a07c 7000e000 []
| 40 0 7000a000 7000a0a0 7000a000 []
after
| Section to fixup .eh_frame @7000a060
| =========================================================
| r_off r_add st_value ADDRESS VALUE
| =========================================================
| 1c 0 7000e000 7000a07c 7000e000 [.init.text]
| 40 0 7000a000 7000a0a0 7000a000 [.exit.text]
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
The loop was really needed in .debug_frame regime where wanted make it
as SH_ALLOC so that apply_relocate_add() would process it. That's not
needed for .eh_frame, so we check this in apply_relocate_add() which
gets called for each section.
Note that we need to save reference to "section name strings" section in
module_frob_arch_sections() since apply_relocate_add() doesn't get that
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
The motivation is to identify ARC750 vs. ARC770 (we currently print
generic "ARC700").
A given ARC700 release could be 750 or 770, with same ARCNUM (or family
identifier which is unfortunate). The existing arc_cpu_tbl[] kept a single
concatenated string for core name and release which thus doesn't work
for 750 vs. 770 identification.
So split this into 2 tables, one with core names and other with release.
And while we are at it, get rid of the range checking for family numbers.
We just document the known to exist cores running Linux and ditch
others.
With this in place, we add detection of ARC750 which is
- cores 0x33 and before
- cores 0x34 and later with MMUv2
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
This came to light when helping a customer with oldish ARC750 core who
were getting instruction errors because of lack of SWAPE but boot log
was incorrectly printing it as being present
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
On older arc700 cores, some of the features configured were not present
in Build config registers. To print about them at boot, we just use the
Kconfig option i.e. whether linux is built to use them or not.
So yes this seems bogus, but what else can be done. Moreover if linux is
booting with these enabled, then the Kconfig info is a good indicator
anyways.
Over time these "hacks" accumulated in read_arc_build_cfg_regs() as well
as arc_cpu_mumbojumbo(). so refactor and move all of those in a single
place: read_arc_build_cfg_regs(). This causes some code redcution too:
| bloat-o-meter2 arch/arc/kernel/setup.o.0 arch/arc/kernel/setup.o.1
| add/remove: 0/0 grow/shrink: 2/1 up/down: 64/-132 (-68)
| function old new delta
| setup_processor 610 670 +60
| cpuinfo_arc700 76 80 +4
| arc_cpu_mumbojumbo 752 620 -132
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Previously we would not print the case when IOC existed but was not
enabled.
And while at it, reduce one line off boot printing by consolidating
the Peripheral address space and IO-Coherency which in a way
applies to them
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Older ARC700 cores (ARC750 specifically) lack instructions to implement
atomic r-w-w. This is problematic for userspace libraries such as NPTL
which need atomic primitives. So enable them by providing kernel assist.
This is costly but really the only sane soluton (othern than tight
spinning using the otherwise availiable atomic exchange EX instruciton).
Good thing is there are only a few of these cores running Linux out in
the wild.
This only works on UP systems.
Reviewed-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
num_possible_cpus() returns how many CPUs may be present on system.
However we want the highest possible CPU number.
This may be differ in a sparsed possible CPUs map.
Such map achived by OF for plat-eznps.
For example if we have:
possible cpus mask 0,3
Then:
num_possible_cpus() is equal 2
while
nr_cpu_ids is equal 4.
Only for value 4 c_start() will provide correct cpuinfo at procfs.
Signed-off-by: Noam Camus <noamc@ezchip.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
The IDU intc is technically part of MCIP (Multi-core IP) hence
historically was only available in a SMP hardware build (and thus only
in a SMP kernel build). Now that hardware restriction has been lifted,
so a UP kernel needs to support it.
This requires breaking mcip.c into parts which are strictly SMP
(inter-core interrupts) and IDU which in reality is just another
intc and thus has no bearing on SMP.
This change allows IDU in UP builds and with a suitable device tree, we
can have the cascaded intc system
ARCv2 core intc <---> ARCv2 IDU intc <---> periperals
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
When doing an nmi backtrace of many cores, most of which are idle, the
output is a little overwhelming and very uninformative. Suppress
messages for cpus that are idling when they are interrupted and just
emit one line, "NMI backtrace for N skipped: idling at pc 0xNNN".
We do this by grouping all the cpuidle code together into a new
.cpuidle.text section, and then checking the address of the interrupted
PC to see if it lies within that section.
This commit suitably tags x86 and tile idle routines, and only adds in
the minimal framework for other architectures.
Link: http://lkml.kernel.org/r/1472487169-14923-5-git-send-email-cmetcalf@mellanox.com
Signed-off-by: Chris Metcalf <cmetcalf@mellanox.com>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Tested-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Tested-by: Daniel Thompson <daniel.thompson@linaro.org> [arm]
Tested-by: Petr Mladek <pmladek@suse.com>
Cc: Aaron Tomlin <atomlin@redhat.com>
Cc: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In the end of "arc_init_IRQ" STATUS32.IE flag is going to be affected by
"flag" instruction but "flag" never touches IE flag on ARCv2. So "kflag"
instruction must be used instead of "flag".
Signed-off-by: Yuriy Kolerov <yuriy.kolerov@synopsys.com>
Cc: stable@vger.kernel.org #4.2+
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
We used to keep the .exit.* sections as linker would fail in final link
due to references from .debug_frame which itself could not be discardrd
due to the forced "write,alloc" attributes for it.
| LD init/built-in.o
| `.exit.text' referenced in section `.debug_frame' of arch/arc/built-in.o: defined in discarded section `.exit.text' of arch/arc/built-in.o
| Makefile:949: recipe for target 'vmlinux' failed
With .debug_frame now retired, this hack is no longer needed.
kernel binary is now a little bit smaller as well.
closes STAR 9000549913
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
This uses a new set of annoations viz. ENTRY_CFI/END_CFI to enabel cfi
ops generation.
Note that we didn't change the normal ENTRY/EXIT as we don't actually
want unwind info in the trap/exception/interrutp handlers which use
these, as unwinder then gets confused (it keeps recursing vs. stopping).
Semantically these are leaf routines and unwinding should stop when it
hits those routines.
Before
------
28.52% 1.19% 9929 hackbench libuClibc-1.0.17.so [.] __write_nocancel
|
---__write_nocancel
|--8.95%--EV_Trap
| --8.25%--sys_write
| |--3.93%--sock_write_iter
...
|--2.62%--memset <==== [LEAF entry as no unwind info]
^^^^^^
After
-----
29.46% 1.24% 13622 hackbench libuClibc-1.0.17.so [.] __write_nocancel
|
---__write_nocancel
|--9.31%--EV_Trap
| --8.62%--sys_write
| |--4.17%--sock_write_iter
...
|--6.19%--sys_write
| --6.19%--sock_write_iter
| unix_stream_sendmsg
| |--1.62%--sock_alloc_send_pskb
| |--0.89%--sock_def_readable
| |--0.88%--_raw_spin_unlock_irqrestore
| |--0.69%--memset
| | ^^^^^^ <==== [now in proper callframe]
| |
| --0.52%--skb_copy_datagram_from_iter
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
This essentially removes ENTRY() assembler annotation for this symbol
since it didn't have a pairing END()
This in ahead of introducing cfi pseudo ops in ENTRY/END which expects
paired cfi_startproc/cfi_endproc
| ../arch/arc/kernel/entry.S: Assembler messages:
| ../arch/arc/kernel/entry.S:270: Error: previous CFI entry not closed (missing .cfi_endproc)
| ../scripts/Makefile.build:326: recipe for target 'arch/arc/kernel/entry-arcv2.o' failed
| make[4]: *** [arch/arc/kernel/entry-arcv2.o] Error 1
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
So finally after almost 8 years of dealing with .debug_frame, we are
finally switching to .eh_frame. The reason being stripped kernel
binaries had non-functional unwinder as .debug_frame was gone.
Also, in general .eh_frame seems more common way of doing unwinding.
This also folds a revert of f52e126cc7 ("ARC: unwind: ensure that
.debug_frame is generated (vs. .eh_frame)") to ensure that we start
getting .eh_frame
Reported-by: Daniel Mentz <danielmentz@google.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
We used to live with PERF_COUNT_HW_CACHE_REFERENCES and
PERF_COUNT_HW_CACHE_REFERENCES not specified on ARC.
Those events are actually aliases to 2 cache events that we do support
and so this change sets "cache-reference" and "cache-misses" events
in the same way as "L1-dcache-loads" and L1-dcache-load-misses.
And while at it adding debug info for cache events as well as doing a
subtle fix in HW events debug info - config value is much better
represented by hex so we may see not only event index but as well other
control bits set (if they exist).
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-snps-arc@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
HS release 3.0 provides for even more flexibility in specifying the
volatile address space for mapping peripherals.
With HS 2.1 @start was made flexible / programmable - with HS 3.0 even
@end can be setup (vs. fixed to 0xFFFF_FFFF before).
So add code to reflect that and while at it remove an unused struct
defintion
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
On faulting sigreturn we do get SIGSEGV, all right, but anything
we'd put into pt_regs could end up in the coredump. And since
__copy_from_user() never zeroed on arc, we'd better bugger off
on its failure without copying random uninitialized bits of
kernel stack into pt_regs...
Cc: stable@vger.kernel.org
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Some module using div_u64() was failing to link because the libgcc 64-bit
divide assist routine was not being exported for modules
Reported-by: avinashp@quantenna.com
Cc: stable@vger.kernel.org
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
The syscall ABI includes the gcc functional calling ABI since a syscall
implies userland caller and kernel callee.
The current gcc ABI (v3) for ARCv2 ISA required 64-bit data be passed in
even-odd register pairs, (potentially punching reg holes when passing such
values as args). This was partly driven by the fact that the double-word
LDD/STD instructions in ARCv2 expect the register alignment and thus gcc
forcing this avoids extra MOV at the cost of a few unused register (which we
have plenty anyways).
This however was rejected as part of upstreaming gcc port to HS. So the new
ABI v4 doesn't enforce the even-odd reg restriction.
Do note that for ARCompact ISA builds v3 and v4 are practically the same in
terms of gcc code generation.
In terms of change management, we infer the new ABI if gcc 6.x onwards
is used for building the kernel.
This also needs a stable backport to enable older kernels to work with
new tools/user-space
Cc: <stable@vger.kernel.org>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
- Removal of most of_platform_populate() calls in arch code. Now the DT
core code calls it in the default case and platforms only need to call
it if they have special needs.
- Use pr_fmt on all the DT core print statements.
- CoreSight binding doc improvements to block name descriptions.
- Add dt_to_config script which can parse dts files and list
corresponding kernel config options.
- Fix memory leak hit with a PowerMac DT.
- Correct a bunch of STMicro compatible strings to use the correct
vendor prefix.
- Fix DA9052 PMIC binding doc to match what is actually used in dts
files.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=wLMr
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull DeviceTree updates from Rob Herring:
- remove most of_platform_populate() calls in arch code. Now the DT
core code calls it in the default case and platforms only need to
call it if they have special needs
- use pr_fmt on all the DT core print statements
- CoreSight binding doc improvements to block name descriptions
- add dt_to_config script which can parse dts files and list
corresponding kernel config options
- fix memory leak hit with a PowerMac DT
- correct a bunch of STMicro compatible strings to use the correct
vendor prefix
- fix DA9052 PMIC binding doc to match what is actually used in dts
files
* tag 'devicetree-for-4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (35 commits)
documentation: da9052: Update regulator bindings names to match DA9052/53 DTS expectations
xtensa: Partially Revert "xtensa: Remove unnecessary of_platform_populate with default match table"
xtensa: Fix build error due to missing include file
MIPS: ath79: Add missing include file
Fix spelling errors in Documentation/devicetree
ARM: dts: fix STMicroelectronics compatible strings
powerpc/dts: fix STMicroelectronics compatible strings
Documentation: dt: i2c: use correct STMicroelectronics vendor prefix
scripts/dtc: dt_to_config - kernel config options for a devicetree
of: fdt: mark unflattened tree as detached
of: overlay: add resolver error prints
coresight: document binding acronyms
Documentation/devicetree: document cavium-pip rx-delay/tx-delay properties
of: use pr_fmt prefix for all console printing
of/irq: Mark initialised interrupt controllers as populated
of: fix memory leak related to safe_name()
Revert "of/platform: export of_default_bus_match_table"
of: unittest: use of_platform_default_populate() to populate default bus
memory: omap-gpmc: use of_platform_default_populate() to populate default bus
bus: uniphier-system-bus: use of_platform_default_populate() to populate default bus
...
Pull smp hotplug updates from Thomas Gleixner:
"This is the next part of the hotplug rework.
- Convert all notifiers with a priority assigned
- Convert all CPU_STARTING/DYING notifiers
The final removal of the STARTING/DYING infrastructure will happen
when the merge window closes.
Another 700 hundred line of unpenetrable maze gone :)"
* 'smp-hotplug-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (70 commits)
timers/core: Correct callback order during CPU hot plug
leds/trigger/cpu: Move from CPU_STARTING to ONLINE level
powerpc/numa: Convert to hotplug state machine
arm/perf: Fix hotplug state machine conversion
irqchip/armada: Avoid unused function warnings
ARC/time: Convert to hotplug state machine
clocksource/atlas7: Convert to hotplug state machine
clocksource/armada-370-xp: Convert to hotplug state machine
clocksource/exynos_mct: Convert to hotplug state machine
clocksource/arm_global_timer: Convert to hotplug state machine
rcu: Convert rcutree to hotplug state machine
KVM/arm/arm64/vgic-new: Convert to hotplug state machine
smp/cfd: Convert core to hotplug state machine
x86/x2apic: Convert to CPU hotplug state machine
profile: Convert to hotplug state machine
timers/core: Convert to hotplug state machine
hrtimer: Convert to hotplug state machine
x86/tboot: Convert to hotplug state machine
arm64/armv8 deprecated: Convert to hotplug state machine
hwtracing/coresight-etm4x: Convert to hotplug state machine
...
Things have been calm here - nothing much except for a few fixes
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJXm7MUAAoJEGnX8d3iisJeTbkP/3z5vrczERECRsaHGU6KpaUP
F9+SpDG+BmCzcKhz60GzY64p6gl2KWtbE3es66lQf45yHD7s3UhAH1Zxc6pFgZjn
JTF8z3LFRDlKQ0H4gVxWsDp4+QXn3LOklckUpgqTocLxNpg9qXVXCVZhoUb12A3d
AxPtOUGsFTtC1e6wnYofGknJjApRls8f11CYmJdQ8aS9lLC/pA+fC0U0fM7LUzx5
DE+KLB3LithYxQ9TBfVrFSbCTbyxxDmYE59v9DEZQftn9pwVMtZLpGEs4BVO31fw
bQLvROfx5xn1yElN4yH2XT6q+N47XA6MtJ3qDvjPN59yWYwP9mOCWlfoIJ0q8UY0
sduU+9K1qZ5WQkXjh66+tPUKpm01YrZy2vghkCJ6YWXnOg9WzbYZQtkwia5TyU8h
lQ36ri72ncK9gPfOSxQGmxY19o7ujX9our9T+bQ4JyjtMicCVKlxSGJLruyTd2ma
LqOjqpLuZv2Ryf/2UbpoOmCsynfjqSLLc2CR+jlGJvH1vD9ycvfjMS1dcTcpcJ3Z
AcsEDBoviMRbM2mWCybtT5gs35vzWWCpgsi+hG4lg0kYtrclGWsc2/uG13BFNK3w
N9/aKgy6a8hYWWOEpKzqzuonR13oob91pDbkUD/m8uS9PSg/5W4WFlvgAjOIog9G
pfL3M6oF/gEZ4CByLS7J
=/rhI
-----END PGP SIGNATURE-----
Merge tag 'arc-4.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc
Pull ARC updates from Vineet Gupta:
"Things have been calm here - nothing much except for a few fixes"
* tag 'arc-4.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc:
ARC: mm: don't loose PTE_SPECIAL in pte_modify()
ARC: dma: fix address translation in arc_dma_free
ARC: typo fix in mm/ioremap.c
ARC: fix linux-next build breakage
Pull the clockevents/clocksource tree from Daniel Lezcano:
- Convert the clocksource-probe init functions to return a value in order to
prepare the consolidation of the drivers using the DT. It is a big patchset
but went through 01.org (kbuild bot), linux next and kernel-ci (continuous
integration) (Daniel Lezcano)
- Fix a bad error handling by returning the right value for cadence_ttc
(Christophe Jaillet)
- Fix typo in the Kconfig for the Samsung pwm (Alexandre Belloni)
- Change functions to static for armada-370-xp and digicolor (Ben Dooks)
- Add support for the rk3399 SoC timer by adding bindings and a slight
change in the base address. Take the opportunity to add the DYNIRQ flag
(Huang Tao)
- Fix endian accessors for the Samsung pwm timer (Matthew Leach)
- Add Oxford Semiconductor RPS Dual Timer driver (Neil Armstrong)
- Add a kernel parameter to swich on/off the event stream feature of the arch
arm timer (Will Deacon)
All the clocksource drivers's init function are now converted to return
an error code. CLOCKSOURCE_OF_DECLARE is no longer used as well as the
clksrc-of table.
Let's convert back the names:
- CLOCKSOURCE_OF_DECLARE_RET => CLOCKSOURCE_OF_DECLARE
- clksrc-of-ret => clksrc-of
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
For exynos_mct and samsung_pwm_timer:
Acked-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
For arch/arc:
Acked-by: Vineet Gupta <vgupta@synopsys.com>
For mediatek driver:
Acked-by: Matthias Brugger <matthias.bgg@gmail.com>
For the Rockchip-part
Acked-by: Heiko Stuebner <heiko@sntech.de>
For STi :
Acked-by: Patrice Chotard <patrice.chotard@st.com>
For the mps2-timer.c and versatile.c changes:
Acked-by: Liviu Dudau <Liviu.Dudau@arm.com>
For the OXNAS part :
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
For LPC32xx driver:
Acked-by: Sylvain Lemieux <slemieux.tyco@gmail.com>
For Broadcom Kona timer change:
Acked-by: Ray Jui <ray.jui@broadcom.com>
For Sun4i and Sun5i:
Acked-by: Chen-Yu Tsai <wens@csie.org>
For Meson6:
Acked-by: Carlo Caione <carlo@caione.org>
For Keystone:
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
For NPS:
Acked-by: Noam Camus <noamca@mellanox.com>
For bcm2835:
Acked-by: Eric Anholt <eric@anholt.net>
The init functions do not return any error. They behave as the following:
- panic, thus leading to a kernel crash while another timer may work and
make the system boot up correctly
or
- print an error and let the caller unaware if the state of the system
Change that by converting the init functions to return an error conforming
to the CLOCKSOURCE_OF_RET prototype.
Proper error handling (rollback, errno value) will be changed later case
by case, thus this change just return back an error or success in the init
function.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
If CONFIG_ARC_DW2_UNWIND is disabled every time arc_unwind_core()
gets called following message gets printed in debug console:
----------------->8---------------
CONFIG_ARC_DW2_UNWIND needs to be enabled
----------------->8---------------
That message makes sense if user indeed wants to see a backtrace or
get nice function call-graphs in perf but what if user disabled
unwinder for the purpose? Why pollute his debug console?
So instead we'll warn user about possibly missing feature once and
let him decide if that was what he or she really wanted.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: stable@vger.kernel.org
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
After patch "of/platform: Add common method to populate default bus",
it is possible for arch code to remove unnecessary callers of
of_platform_populate with default match table.
Acked-by: Vineet Gupta <vgupta@synopsys.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Signed-off-by: Rob Herring <robh@kernel.org>
ARC700 support for 2 interrupt priorities historically allowed even slow
perpherals such as emac and uart to setup high priority interrupts
which was wrong from the beginning as they could possibly delay the more
critical timer interrupt.
The hardware support for 2 level interrupts in ARCompact is less than
ideal anyways (judging from the "hacks" in low level entry code and thus
is not used in productions systems I know of.
So reduce the scope of this to timer only, thereby reducing a bunch of
complexity.
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Pull perf updates from Ingo Molnar:
"Mostly tooling and PMU driver fixes, but also a number of late updates
such as the reworking of the call-chain size limiting logic to make
call-graph recording more robust, plus tooling side changes for the
new 'backwards ring-buffer' extension to the perf ring-buffer"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (34 commits)
perf record: Read from backward ring buffer
perf record: Rename variable to make code clear
perf record: Prevent reading invalid data in record__mmap_read
perf evlist: Add API to pause/resume
perf trace: Use the ptr->name beautifier as default for "filename" args
perf trace: Use the fd->name beautifier as default for "fd" args
perf report: Add srcline_from/to branch sort keys
perf evsel: Record fd into perf_mmap
perf evsel: Add overwrite attribute and check write_backward
perf tools: Set buildid dir under symfs when --symfs is provided
perf trace: Only auto set call-graph to "dwarf" when syscalls are being traced
perf annotate: Sort list of recognised instructions
perf annotate: Fix identification of ARM blt and bls instructions
perf tools: Fix usage of max_stack sysctl
perf callchain: Stop validating callchains by the max_stack sysctl
perf trace: Fix exit_group() formatting
perf top: Use machine->kptr_restrict_warned
perf trace: Warn when trying to resolve kernel addresses with kptr_restrict=1
perf machine: Do not bail out if not managing to read ref reloc symbol
perf/x86/intel/p4: Trival indentation fix, remove space
...
Define HAVE_EXIT_THREAD for archs which want to do something in
exit_thread. For others, let's define exit_thread as an empty inline.
This is a cleanup before we change the prototype of exit_thread to
accept a task parameter.
[akpm@linux-foundation.org: fix mips]
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: "James E.J. Bottomley" <jejb@parisc-linux.org>
Cc: Aurelien Jacquiot <a-jacquiot@ti.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Chen Liqin <liqin.linux@gmail.com>
Cc: Chris Metcalf <cmetcalf@mellanox.com>
Cc: Chris Zankel <chris@zankel.net>
Cc: David Howells <dhowells@redhat.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Guan Xuetao <gxt@mprc.pku.edu.cn>
Cc: Haavard Skinnemoen <hskinnemoen@gmail.com>
Cc: Hans-Christian Egtvedt <egtvedt@samfundet.no>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Helge Deller <deller@gmx.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Jesper Nilsson <jesper.nilsson@axis.com>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: Jonas Bonn <jonas@southpole.se>
Cc: Koichi Yasutake <yasutake.koichi@jp.panasonic.com>
Cc: Lennox Wu <lennox.wu@gmail.com>
Cc: Ley Foon Tan <lftan@altera.com>
Cc: Mark Salter <msalter@redhat.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Max Filippov <jcmvbkbc@gmail.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Mikael Starvik <starvik@axis.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Rich Felker <dalias@libc.org>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Richard Kuo <rkuo@codeaurora.org>
Cc: Richard Weinberger <richard@nod.at>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Steven Miao <realmz6@gmail.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This makes perf_callchain_{user,kernel}() receive the max stack
as context for the perf_callchain_entry, instead of accessing
the global sysctl_perf_event_max_stack.
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Alexei Starovoitov <ast@kernel.org>
Cc: Brendan Gregg <brendan.d.gregg@gmail.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: He Kuang <hekuang@huawei.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Milian Wolff <milian.wolff@kdab.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Cc: Wang Nan <wangnan0@huawei.com>
Cc: Zefan Li <lizefan@huawei.com>
Link: http://lkml.kernel.org/n/tip-kolmn1yo40p7jhswxwrc7rrd@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
With generic "identity" num of CPUs is limited to 256 (8 bit).
We use our alternative AUX register GLOBAL_ID (12 bit).
Now we can support up to 4096 CPUs.
Signed-off-by: Noam Camus <noamc@ezchip.com>
In SMP setup, master loops for each_present_cpu calling cpu_up().
For ARC it returns as soon as new cpu's status becomes online,
However secondary may still do HW initializing,
machine or platform hook level.
So turn secondary online only after all HW setup is done.
Signed-off-by: Noam Camus <noamc@ezchip.com>
Acked-by: Vineet Gupta <vgupta@synopsys.com>
There are no more users of this - so RIP!
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
[vgupta: update changelog]
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
We no longer use it and instead a real clk device such as fixed-clk
instance is fed to timers etc.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
[vgupta: broken out of a bigger patch, rewrote changelog]
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
UARTs usually have fixed clock so we're switching to use of
constant values instead of something derived from core clock
frequency.
Among other things this will allow us to get rid of
arc_{get|set}_core_freq() and switch to generic clock
framework later on.
Acked-by: Christian Ruppert <christian.ruppert@alitech.com>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Now that we have Timers probed from DT, don't need legacy domain
This however requires mapping to be called explicitly for the IRQ which
still can't (and probably never) be probed from DT such as IPI and
SOFTIRQ
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
The primary interrupt handler arch_do_IRQ() was passing hwirq as linux
virq to core code. This was fragile and worked so far as we only had legacy/linear
domains.
This came out of a rant by Marc Zyngier.
http://lists.infradead.org/pipermail/linux-snps-arc/2015-December/000298.html
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Noam Camus <noamc@ezchip.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
This will be needed for switching to linear irq domain as
irq_create_mapping() called by intr code needs the IRQ numbers
in addition to existing usage in mcip.c for requesting the irq
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
- Remove explicit clocksource setup and let it be done by OF framework
by defining CLOCKSOURCE_OF_DECLARE() for various timers
- This allows multiple clocksources to be potentially registered
simultaneouly: previously we could only do one - as all of them had
same arc_counter_setup() routine for registration
- Setup routines also ensure that the underlying timer actually exists.
- Remove some of the panic() calls if underlying timer is NOT detected as
fallback clocksource might still be available
1. If GRFC doesn't exist, jiffies clocksource gets registered anyways
2. if RTC doesn't exist, TIMER1 can take over (as it is always
present)
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
- timer frequency is derived from DT (no longer rely on top level
DT "clock-frequency" probed early and exported by asm/clk.h)
- TIMER0_IRQ need not be exported across arch code, confined to intc as
it is property of same
- Any failures in clockevent setup are considered pedantic and system
panic()'s as there is no generic fallback (unlike clocksource where
a jiffies based soft clocksource always exists)
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
- call clocksource_probe()
- This in turns needs of_clk_init() to be called earlier
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Noam Camus <noamc@ezchip.com>
[vgupta: broken off from a bigger patch]
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
ARC Timers so far have been handled as "legacy" w/o explicit description
in DT. This poses challenge for newer platforms wanting to use them.
This series will eventually help move timers over to DT.
This patch does a small change of using a CPU notifier to set clockevent
on non-boot CPUs. So explicit setup is done only on boot CPU (which will
later be done by DT)
Signed-off-by: Noam Camus <noamc@ezchip.com>
[vgupta: broken off from a bigger patch]
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
- The idea is to remove the API usage since it has a subltle
design flaw - relies on being called on cpu0 first. This is true for
some early per cpu irqs such as TIMER/IPI, but not for late probed
per cpu peripherals such a perf. And it's usage in perf has already
bitten us once: see c6317bc7c5
("ARCv2: perf: Ensure perf intr gets enabled on all cores") where we
ended up open coding it anyways
- The seeming duplication will go away once we start using cpu notifier
for timer setup
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
- The asm helpers for calling into irq tracer were missing
- Add calls to above helpers in low level assembly entry code for ARCv2
- irq_save() uses CLRI to disable interrupts and returns the prev interrupt
state (in STATUS32) in a specific encoding (and not the raw value of
STATUS32). This is usable with SETI in irq_restore(). However
save_flags() reads the raw value of STATUS32 which doesn't pair with
irq_save/restore() and thus needs fixing.
Signed-off-by: Evgeny Voevodin <evgeny.voevodin@intel.com>
[vgupta: updated changelog and also added some comments]
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
- Big Endian io accessors fix [Lada]
- Spellos fixes [Adam]
- Fix for DW GMAC breakage [Alexey]
- Making DMA API 64-bit ready
- Shutting up -Wmaybe-uninitialized noise for ARC
- Other minor fixes here and there, comments update
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=n0fk
-----END PGP SIGNATURE-----
Merge tag 'arc-4.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc
Pull ARC architecture updates from Vineet Gupta:
- Big Endian io accessors fix [Lada]
- Spellos fixes [Adam]
- Fix for DW GMAC breakage [Alexey]
- Making DMA API 64-bit ready
- Shutting up -Wmaybe-uninitialized noise for ARC
- Other minor fixes here and there, comments update
* tag 'arc-4.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc: (21 commits)
ARCv2: ioremap: Support dynamic peripheral address space
ARC: dma: reintroduce platform specific dma<->phys
ARC: dma: ioremap: use phys_addr_t consistenctly in code paths
ARC: dma: pass_phys() not sg_virt() to cache ops
ARC: dma: non-coherent pages need V-P mapping if in HIGHMEM
ARC: dma: Use struct page based page allocator helpers
ARC: build: Turn off -Wmaybe-uninitialized for ARC gcc 4.8
ARC: [plat-axs10x] add Ethernet PHY description in .dts
arc: use of_platform_default_populate() to populate default bus
ARC: thp: unbork !CONFIG_TRANSPARENT_HUGEPAGE build
arc: [plat-nsimosci*] use ezchip network driver
ARCv2: LLSC: software backoff is NOT needed starting HS2.1c
ARC: mm: Use virt_to_pfn() for addr >> PAGE_SHIFT pattern
ARC: [plat-nsim] document ranges
ARC: build: Better way to detect ISA compatible toolchain
ARCv2: Allow enabling PAE40 w/o HIGHMEM
ARC: [BE] readl()/writel() to work in Big Endian CPU configuration
ARC: [*defconfig] No need to specify CONFIG_CROSS_COMPILE
ARC: [BE] Select correct CROSS_COMPILE prefix
ARC: bitops: Remove non relevant comments
...
The peripheral address space is architectural address window which is
uncached and typically used to wire up peripherals.
For ARC700 cores (ARCompact ISA based) this was fixed to 1GB region
0xC000_0000 - 0xFFFF_FFFF.
For ARCv2 based HS38 cores the start address is flexible and can be
0xC, 0xD, 0xE, 0xF 000_000 by programming AUX_NON_VOLATILE_LIMIT reg
(typically done in bootloader)
Further in cas of PAE, the physical address can extend beyond 4GB so
need to confine this check, otherwise all pages beyond 4GB will be
treated as uncached
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Use helper of_platform_default_populate() in linux/of_platform
when possible, instead of calling of_platform_populate() with
the default match table.
Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Add PCI support to ARC and update drivers/pci Makefile enabling the ARC
arch to use the generic PCI setup functions.
[bhelgaas: fold in Joao's pci-dma-compat.h & pci-bridge.h build fix (I
should have caught this myself, sorry]
Signed-off-by: Joao Pinto <jpinto@synopsys.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Vineet Gupta <vgupta@synopsys.com>
Let the non boot cpus call into idle with the corresponding hotplug state, so
the hotplug core can handle the further bringup. That's a first step to
convert the boot side of the hotplugged cpus to do all the synchronization
with the other side through the state machine. For now it'll only start the
hotplug thread and kick the full bringup of the cpu.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-arch@vger.kernel.org
Cc: Rik van Riel <riel@redhat.com>
Cc: Rafael Wysocki <rafael.j.wysocki@intel.com>
Cc: "Srivatsa S. Bhat" <srivatsa@mit.edu>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Sebastian Siewior <bigeasy@linutronix.de>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Paul McKenney <paulmck@linux.vnet.ibm.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Paul Turner <pjt@google.com>
Link: http://lkml.kernel.org/r/20160226182341.614102639@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Previous Commit ("ARC: SMP: No need for CONFIG_ARC_IPI_DBG") removed
the Kconfig option ARC_IPI_DBG. Remove the last reference on this
option.
Signed-off-by: Valentin Rothberg <valentinrothberg@gmail.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
ARConnect/MCIP IPI sending has a retry-wait loop in case caller had
not seen a previous such interrupt. Turns out that it is not needed at
all. Linux cross core calling allows coalescing multiple IPIs to same
receiver - it is fine as long as there is one.
This logic is built into upper layer already, at a higher level of
abstraction. ipi_send_msg_one() sets the actual msg payload, but it only
calls MCIP IPI sending if msg holder was empty (using
atomic-set-new-and-get-old construct). Thus it is unlikely that the
retry-wait looping was ever getting exercised at all.
Cc: Chuck Jordan <cjordan@synopsys.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
There is no real ARC700 based SMP SoC so remove IPI definition.
EZChip's SMP ARC700 is going to use a different intc and IPI provider
anyways.
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
ARConnect/MCIP Inter-Core-Interrupt module can't send interrupt to
local core. So use core intc capability to trigger software
interrupt to self, using an unsued IRQ #21.
This showed up as csd deadlock with LTP trace_sched on a dual core
system. This test acts as scheduler fuzzer, triggering all sorts of
schedulting activity. Trouble starts with IPI to self, which doesn't get
delivered (effectively lost due to H/w capability), but the msg intended
to be sent remain enqueued in per-cpu @ipi_data.
All subsequent IPIs to this core from other cores get elided due to the
IPI coalescing optimization in ipi_send_msg_one() where a pending msg
implies an IPI already sent and assumes other core is yet to ack it.
After the elided IPI, other core simply goes into csd_lock_wait()
but never comes out as this core never sees the interrupt.
Fixes STAR 9001008624
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: <stable@vger.kernel.org> [4.2]
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
- ARCv2 uses a seperate BCR for {I,D}CCM base address:
ARCompact encoded both base/size in same BCR
- Size encoding in common BCR is different for ARCompact/ARCv2
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
It is unlikely that designs running Linux will not have multiplier.
Further the current support is not complete as tool don't generate a
multilib w/o multiplier.
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
- Corner case of returning to delay slot from interrupt
- Changing default interrupt prioiry level
- Kconfig'ize support for super pages
- Other minor fixes
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=FNDd
-----END PGP SIGNATURE-----
Merge tag 'arc-4.5-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc
Pull ARC fixes from Vineet Gupta:
"I've been sitting on some of these fixes for a while.
- Corner case of returning to delay slot from interrupt
- Changing default interrupt prioiry level
- Kconfig'ize support for super pages
- Other minor fixes"
* tag 'arc-4.5-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc:
ARC: mm: Introduce explicit super page size support
ARCv2: intc: Allow interruption by lowest priority interrupt
ARCv2: Check for LL-SC livelock only if LLSC is enabled
ARC: shrink cpuinfo by not saving full timer BCR
ARCv2: clocksource: Rename GRTC -> GFRC ...
ARCv2: STAR 9000950267: Handle return from intr to Delay Slot #2
ARC HS Cores support configurable multiple interrupt priorities of upto
16 levels.
There is processor "interrupt preemption threshhold" in STATUS32.E[4:1]
And several places need to set this up:
1. seed value as kernel is booting
2. seed value for user space programs
3. Arg to SLEEP instruction in idle task (what interrupt prio can wake)
4. Per-IRQ line prioirty (i.e. what is the priority of interrupt
raised by a peripheral or timer or perf counter...
Currently above sites use the highest priority 0. This can be potential
problem when multiple priorities are supported. e.g. user space could
only be interrupted by P0 interrupt, not others...
So turn this over and instead make default interruption level to be
the lowest priority possible 15. This should be fine even if there are
fewer priority levels configured (say two: P0 HIGH, P1 LOW)
This feature also effectively disables FIRQ feature if present in
hardware config. With old code, a P0 interrupt would be FIRQ, needing
special handling (ISR or Register Banks) which is NOT supported yet.
Now it not be P0 (P15 or whatever is lowest prio) so FIRQ is not
triggered.
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Returning to delay slot, riding an interrupti, had one loose end.
AUX_USER_SP used for restoring user mode SP upon RTIE was not being
setup from orig task's saved value, causing task to use wrong SP,
leading to ProtV errors.
The reason being:
- INTERRUPT_EPILOGUE returns to a kernel trampoline, thus not expected to restore it
- EXCEPTION_EPILOGUE is not used at all
Fix that by restoring AUX_USER_SP explicitly in the trampoline.
This was broken in the original workaround, but the error scenarios got
reduced considerably since v3.14 due to following:
1. The Linuxthreads.old based userspace at the time caused many more
exceptions in delay slot than the current NPTL based one.
Infact with current userspace the error doesn't happen at all.
2. Return from interrupt (delay slot or otherwise) doesn't get exercised much
after commit 4de0e52867 ("Really Re-enable interrupts to avoid deadlocks")
since IRQ_ACTIVE.active being clear means most returns are as if from pure
kernel (even for active interrupts)
Infact the issue only happened in an experimental branch where I was tinkering with
reverted 4de0e52867
Cc: stable@kernel.org # v4.2+
Fixes: 4255b07f2c ("ARCv2: STAR 9000793984: Handle return from intr to Delay Slot")
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Pull livepatching updates from Jiri Kosina:
- RO/NX attribute fixes for patch module relocations from Josh
Poimboeuf. As part of this effort, module.c has been cleaned up as
well and livepatching is piggy-backing on this cleanup. Rusty is OK
with this whole lot going through livepatching tree.
- symbol disambiguation support from Chris J Arges. That series is
also
Reviewed-by: Miroslav Benes <mbenes@suse.cz>
but this came in only after I've alredy pushed out. Didn't want to
rebase because of that, hence I am mentioning it here.
- symbol lookup fix from Miroslav Benes
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/livepatching:
livepatch: Cleanup module page permission changes
module: keep percpu symbols in module's symtab
module: clean up RO/NX handling.
module: use a structure to encapsulate layout.
gcov: use within_module() helper.
module: Use the same logic for setting and unsetting RO/NX
livepatch: function,sympos scheme in livepatch sysfs directory
livepatch: add sympos as disambiguator field to klp_reloc
livepatch: add old_sympos as disambiguator field to klp_func
Blingly ignoring CIE.version != 1 was a bad idea.
It still leaves "desirability" when running perf with callgraphing where libgcc
symbols might show in hotspot.
More importantly, basic CIE.version == 3 support already exists in code:
|
| retAddrReg = state.version <= 1 ? *ptr++ : get_uleb128(&ptr, end);
|
Next commit with simply add continue-not-bail for CIE.version != 1
This reverts commit 323f41f9e7.
This will better reflect its description i.e. "any needed setup..."
and not just do an "IPI request".
Signed-off-by: Noam Camus <noamc@ezchip.com>
Acked-by: Vineet Gupta <vgupta@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
ARC dwarf unwinder only supports CIE version == 1
The boot time dwarf sanitizer (part of binary lookup table constructor)
would simply bail if it saw CIE version == 3, rendering unwinder with a
NULL lookup table.
It seems libgcc linked with kernel does have such entries.
With fallback linear search removed, and a NULL binary lookup table,
unwinder fails to generate any stack trace.
So allow graceful ignoring of unsupported CIE entries.
This problem was initially seen in Alexey's setup (and not mine) as he
was using buildroot built toolchain (libgcc) which doesn't get built with
CFLAGS_FOR_TARGET="-gdwarf-2 which is my default
Fixes STAR 9000985048: "kernel unwinder broken with stock tools"
Fixes: 2e22502c08 ARC: dw2 unwind: Remove falllback linear search thru FDE entries
Reported-by Alexey Brodkin <abrodkin@synopsys.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
The fix which removed linear searching of dwarf (because binary lookup
data always exists) missed out on the fact that modules don't get the
binary lookup tables info. This caused unwinding out of modules to stop
working.
So add binary lookup header setup (equivalent of eh_frame_hdr setup) to
modules as well.
While at it, confine the header setup to within unwinder code,
reducing one API exposed out of unwinder code.
Fixes: 2e22502c08 ARC: dw2 unwind: Remove falllback linear search thru FDE entries
Cc: <stable@vger.kernel.org>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
This was the second perf intr issue
perf sampling on multicore requires intr to be enabled on all cores.
ARC perf probe code used helper arc_request_percpu_irq() which calls
- request_percpu_irq() on core0
- enable_percpu_irq() on all all cores (including core0)
genirq requires that request be made ahead of enable call.
However if perf probe happened on non core0 (observed on a 3.18 kernel),
enable would get called ahead of request, failing obviously and
rendering perf intr disabled on all such cores
[ 11.120000] 1 ARC perf : 8 counters (48 bits), 113 conditions, [overflow IRQ support]
[ 11.130000] 1 -----> enable_percpu_irq() IRQ 20 failed
[ 11.140000] 3 -----> enable_percpu_irq() IRQ 20 failed
[ 11.140000] 2 -----> enable_percpu_irq() IRQ 20 failed
[ 11.140000] 0 =====> request_percpu_irq() IRQ 20
[ 11.140000] 0 -----> enable_percpu_irq() IRQ 20
Fix this fragility, by calling request_percpu_irq() on whatever core
calls probe (there is no requirement on which core calls this anyways)
and then calling enable on each cores.
Interestingly this started as invesigation of STAR 9000838902:
"sporadically IRQs enabled on perf prob"
which was about occassional boot spew as request_percpu_irq got called
non-locally (from an IPI), and re-enabled interrupts in following path
proc_mkdir -> spin_unlock_irq()
which the irq work code didn't like.
| ARC perf : 8 counters (48 bits), 113 conditions, [overflow IRQ support]
|
| BUG: failure at ../kernel/irq_work.c:135/irq_work_run_list()!
| CPU: 0 PID: 0 Comm: swapper/0 Not tainted 3.18.10-01127-g285efb8e66d1 #2
|
| Stack Trace:
| arc_unwind_core.constprop.1+0x94/0x104
| dump_stack+0x62/0x98
| irq_work_run_list+0xb0/0xb4
| irq_work_run+0x22/0x3c
| do_IPI+0x74/0x9c
| handle_irq_event_percpu+0x34/0x164
| handle_percpu_irq+0x58/0x78
| generic_handle_irq+0x1e/0x2c
| arch_do_IRQ+0x3c/0x60
| ret_from_exception+0x0/0x8
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-snps-arc@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Cc: Alexey Brodkin <abrodkin@synopsys.com>
Cc: <stable@vger.kernel.org> #4.2+
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
arc_request_percpu_irq() is called by all cores to request/enable percpu
irq. It has some "prep" calls needed by genirq:
- setup percpu devid
- disable IRQ_NOAUTOEN
However given that enable_percpu_irq() is called enayways, latter can be
avoided.
We are now left with irq_set_percpu_devid() quirk and that too for
ARCompact builds only, since previous patch updated ARCv2 intc to do this
in the "right" place, i.e. irq map function.
By next release, this will ultimately be fixed for ARCompact as well.
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Alexey Brodkin <abrodkin@synopsys.com>
Cc: linux-snps-arc@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Makes it easier to handle init vs core cleanly, though the change is
fairly invasive across random architectures.
It simplifies the rbtree code immediately, however, while keeping the
core data together in the same cachline (now iff the rbtree code is
enabled).
Acked-by: Peter Zijlstra <peterz@infradead.org>
Reviewed-by: Josh Poimboeuf <jpoimboe@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Fixes STAR 9000953410: "perf callgraph profiling causing RCU stalls"
| perf record -g -c 15000 -e cycles /sbin/hackbench
|
| INFO: rcu_preempt self-detected stall on CPU
| 1: (1 GPs behind) idle=609/140000000000002/0 softirq=2914/2915 fqs=603
| Task dump for CPU 1:
in-kernel dwarf unwinder has a fast binary lookup and a fallback linear
search (which iterates thru each of ~11K entries) thus takes 2 orders of
magnitude longer (~3 million cycles vs. 2000). Routines written in hand
assembler lack dwarf info (as we don't support assembler CFI pseudo-ops
yet) fail the unwinder binary lookup, hit linear search, failing
nevertheless in the end.
However the linear search is pointless as binary lookup tables are created
from it in first place. It is impossible to have binary lookup fail while
succeed the linear search. It is pure waste of cycles thus removed by
this patch.
This manifested as RCU stalls / NMI watchdog splat when running
hackbench under perf with callgraph profiling. The triggering condition
was perf counter overflowing in routine lacking dwarf info (like memset)
leading to patheic 3 million cycle unwinder slow path and by the time it
returned new interrupts were already pending (Timer, IPI) and taken
rightaway. The original memset didn't make forward progress, system kept
accruing more interrupts and more unwinder delayes in a vicious feedback
loop, ultimately triggering the NMI diagnostic.
Cc: stable@vger.kernel.org
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
SYNC in __switch_to() is a historic relic and not needed at all.
- In UP context it is obviously useless, why would we want to stall
the core for all updates to stack memory of t0 to complete before
loading kernel mode callee registers from t1 stack's memory.
- In SMP, there could be potential race in which outgoing task could
be concurrently picked for running on a different core, thus writes
to stack here need to be visible before the reads from stack on
other core. Peter confirmed that generic schedular already has needed
barriers (by way of rq lock) so there is no need for additional arch
barrier.
This came up when Noam was trying to replace this SYNC with EZChip
specific hardware thread scheduling instruction for their platform
support.
Link: http://lkml.kernel.org/r/20151102092654.GM17308@twins.programming.kicks-ass.net
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: linux-kernel@vger.kernel.org
Cc: Noam Camus <noamc@ezchip.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Bus errors from userspace on ARCompact based cores are handled by core
as a high priority L2 interrupt but current code treated it as interrupt
Handling an interrupt like exception is certainly not going to go unnoticed.
(and it worked so far as we never saw a Bus error from userspace until
IPPK guys tested a DDR controller with ECC error detection etc hence
needed to explicitly trigger/handle such errors)
- So move mem_service exception handler from common code into ARCv2 code.
- In ARCompact code, define mem_service as L2 interrupt handler which
just drops down to pure kernel mode and goes of to enqueue SIGBUS
Reported-by: Nelson Pereira <npereira@synopsys.com>
Tested-by: Ana Martins <amartins@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
With prev fixes, all cores now start via common entry point @stext which
already calls EARLY_CPU_SETUP for all cores - so no need to invoke it
again
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
MCIP now registers it's own per cpu setup routine (for IPI IRQ request)
using smp_ops.init_irq_cpu().
So no need for platforms to do that. This now completely decouples
platforms from MCIP.
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Note this is not part of platform owned static machine_desc,
but more of device owned plat_smp_ops (rather misnamed) which a IPI
provider or some such typically defines.
This will help us seperate out the IPI registration from platform
specific init_cpu_smp() into device specific init_irq_cpu()
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
MCIP now registers it's own probe callback with smp_ops.init_early_smp()
which is called by ARC common code, so no need for platforms to do that.
This decouples the platforms and MCIP and helps confine MCIP details
to it's own file.
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
This adds a platform agnostic early SMP init hook which is called on
Master core before calling setup_processor()
setup_arch()
smp_init_cpus()
smp_ops.init_early_smp()
...
setup_processor()
How this helps:
- Used for one time init of certain SMP centric IP blocks, before
calling setup_processor() which probes various bits of core,
possibly including this block
- Currently platforms need to call this IP block init from their
init routines, which doesn't make sense as this is specific to ARC
core and not platform and otherwise requires copy/paste in all
(and hence a possible point of failure)
e.g. MCIP init is called from 2 platforms currently (axs10x and sim)
which will go away once we have this.
This change only adds the hooks but they are empty for now. Next commit
will populate them and remove the explicit init calls from platforms.
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
These are not in use for ARC platforms. Moreover DT mechanims exist to
probe them w/o explicit platform calls.
- clocksource drivers can use CLOCKSOURCE_OF_DECLARE()
- intc IRQCHIP_DECLARE() calls + cascading inside DT allows external
intc to be probed automatically
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
The reason this was not done so far was lack of genuine IPI_IRQ for
ARC700, as we don't have a SMP version of core yet (which might change
soon thx to EZChip). Nevertheles to increase the build coverage, we
need to allow CONFIG_SMP for ARC700 and still be able to run it on a
UP platform (nsim or AXS101) with a UP Device Tree (SMP-on-UP)
The build itself requires some define for IPI_IRQ and even a dummy
value is fine since that code won't run anyways.
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
For Run-on-reset, non masters need to spin wait. For Halt-on-reset they
can jump to entry point directly.
Also while at it, made reset vector handler as "the" entry point for
kernel including host debugger based boot (which uses the ELF header
entry point)
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
For non halt-on-reset case, all cores start of simultaneously in @stext.
Master core0 proceeds with kernel boot, while other spin-wait on
@wake_flag being set by master once it is ready. So NO hardware assist
is needed for master to "kick" the others.
This patch moves this soft implementation out of mcip.c (as there is no
hardware assist) into common smp.c
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
This is done by improving the laddering logic !
Before:
if Exception
goto excep_or_pure_k_ret
if !Interrupt(L2)
goto l1_chk
else
INTERRUPT_EPILOGUE 2
l1_chk:
if !Interrupt(L1) (i.e. pure kernel mode)
goto excep_or_pure_k_ret
else
INTERRUPT_EPILOGUE 1
excep_or_pure_k_ret:
EXCEPTION_EPILOGUE
Now:
if !Interrupt(L1 or L2) (i.e. exception or pure kernel mode)
goto excep_or_pure_k_ret
; guaranteed to be an interrupt
if !Interrupt(L2)
goto l1_ret
else
INTERRUPT_EPILOGUE 2
; by virtue of above, no need to chk for L1 active
l1_ret:
INTERRUPT_EPILOGUE 1
excep_or_pure_k_ret:
EXCEPTION_EPILOGUE
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Historically this was done by ARC IDE driver, which is long gone.
IRQ core is pretty robust now and already checks if IRQs are enabled
in hard ISRs. Thus no point in checking this in arch code, for every
call of irq enabled.
Further if some driver does do that - let it bring down the system so we
notice/fix this sooner than covering up for sucker
This makes local_irq_enable() - for L1 only case atleast simple enough
so we can inline it.
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Most interrupt flow handlers do not use the irq argument. Those few
which use it can retrieve the irq number from the irq descriptor.
Remove the argument.
Search and replace was done with coccinelle and some extra helper
scripts around it. Thanks to Julia for her help!
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Julia Lawall <Julia.Lawall@lip6.fr>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Pull irq updates from Thomas Gleixner:
"This updated pull request does not contain the last few GIC related
patches which were reported to cause a regression. There is a fix
available, but I let it breed for a couple of days first.
The irq departement provides:
- new infrastructure to support non PCI based MSI interrupts
- a couple of new irq chip drivers
- the usual pile of fixlets and updates to irq chip drivers
- preparatory changes for removal of the irq argument from interrupt
flow handlers
- preparatory changes to remove IRQF_VALID"
* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (129 commits)
irqchip/imx-gpcv2: IMX GPCv2 driver for wakeup sources
irqchip: Add bcm2836 interrupt controller for Raspberry Pi 2
irqchip: Add documentation for the bcm2836 interrupt controller
irqchip/bcm2835: Add support for being used as a second level controller
irqchip/bcm2835: Refactor handle_IRQ() calls out of MAKE_HWIRQ
PCI: xilinx: Fix typo in function name
irqchip/gic: Ensure gic_cpu_if_up/down() programs correct GIC instance
irqchip/gic: Only allow the primary GIC to set the CPU map
PCI/MSI: pci-xgene-msi: Consolidate chained IRQ handler install/remove
unicore32/irq: Prepare puv3_gpio_handler for irq argument removal
tile/pci_gx: Prepare trio_handle_level_irq for irq argument removal
m68k/irq: Prepare irq handlers for irq argument removal
C6X/megamode-pic: Prepare megamod_irq_cascade for irq argument removal
blackfin: Prepare irq handlers for irq argument removal
arc/irq: Prepare idu_cascade_isr for irq argument removal
sparc/irq: Use access helper irq_data_get_affinity_mask()
sparc/irq: Use helper irq_data_get_irq_handler_data()
parisc/irq: Use access helper irq_data_get_affinity_mask()
mn10300/irq: Use access helper irq_data_get_affinity_mask()
irqchip/i8259: Prepare i8259_irq_dispatch for irq argument removal
...
With all features in place, the ARC HS pct block can now be effectively
allowed to be probed/used
Acked-by: Peter Zijlstra <peterz@infradead.org>
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
* split off pmu info into singleton and per-cpu bits
* setup PMU on all cores
Acked-by: Peter Zijlstra <peterz@infradead.org>
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
In times of ARC 700 performance counters didn't have support of
interrupt an so for ARC we only had support of non-sampling events.
Put simply only "perf stat" was functional.
Now with ARC HS we have support of interrupts in performance counters
which this change introduces support of.
ARC performance counters act in the following way in regard of
interrupts generation.
[1] A counter counts starting from value set in PCT_COUNT register pair
[2] Once counter reaches value set in PCT_INT_CNT interrupt is raised
Basic setup look like this:
[1] PCT_COUNT = 0;
[2] PCT_INT_CNT = __limit_value__;
[3] Enable interrupts for that counter and let it run
[4] Let counter reach its limit
[5] Handle interrupt when it happens
Note that PCT HW block is build in CPU core and so ints interrupt
line (which is basically OR of all counters IRQs) is wired directly to
top-level IRQC. That means do de-assert PCT interrupt it's required to
reset IRQs from all counters that have reached their limit values.
Acked-by: Peter Zijlstra <peterz@infradead.org>
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
This generalization prepares for support of overflow interrupts.
Hardware event counters on ARC work that way:
Each counter counts from programmed start value (set in
ARC_REG_PCT_COUNT) to a limit value (set in ARC_REG_PCT_INT_CNT) and
once limit value is reached this timer generates an interrupt.
Even though this hardware implementation allows for more flexibility,
in Linux kernel we decided to mimic behavior of other architectures
this way:
[1] Set limit value as half of counter's max value (to allow counter to
run after reaching it limit, see below for more explanation):
---------->8-----------
arc_pmu->max_period = (1ULL << counter_size) / 2 - 1ULL;
---------->8-----------
[2] Set start value as "arc_pmu->max_period - sample_period" and then
count up to the limit
Our event counters don't stop on reaching max value (the one we set in
ARC_REG_PCT_INT_CNT) but continue to count until kernel explicitly
stops each of them.
And setting a limit as half of counter capacity is done to allow
capturing of additional events in between moment when interrupt was
triggered until we're actually processing PMU interrupts. That way
we're trying to be more precise.
For example if we count CPU cycles we keep track of cycles while
running through generic IRQ handling code:
[1] We set counter period as say 100_000 events of type "crun"
[2] Counter reaches that limit and raises its interrupt
[3] Once we get in PMU IRQ handler we read current counter value from
ARC_REG_PCT_SNAP ans see there something like 105_000.
If counters stop on reaching a limit value then we would miss
additional 5000 cycles.
Acked-by: Peter Zijlstra <peterz@infradead.org>
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
The number of counters in PCT can never be more than 32 (while
countable conditions could be 100+) for both ARCompact and ARCv2
And while at it update copyright dates.
Acked-by: Peter Zijlstra <peterz@infradead.org>
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
When kernel's binary becomes large enough (32M and more) errors
may occur during the final linkage stage. It happens because
the build system uses short relocations for ARC by default.
This problem may be easily resolved by passing -mlong-calls
option to GCC to use long absolute jumps (j) instead of short
relative branchs (b).
But there are fragments of pure assembler code exist which use
branchs in inappropriate places and cause a linkage error because
of relocations overflow.
First of these fragments is .fixup insertion in futex.h and
unaligned.c. It inserts a code in the separate section (.fixup)
with branch instruction. It leads to the linkage error when
kernel becomes large.
Second of these fragments is calling scheduler's functions
(common kernel code) from entry.S of ARC's code. When kernel's
binary becomes large it may lead to the linkage error because
scheduler may occur far enough from ARC's code in the final
binary.
Signed-off-by: Yuriy Kolerov <yuriy.kolerov@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
This is to workaround the llock/scond livelock
HS38x4 could get into a LLOCK/SCOND livelock in case of multiple overlapping
coherency transactions in the SCU. The exclusive line state keeps rotating
among contenting cores leading to a never ending cycle. So break the cycle
by deferring the retry of failed exclusive access (SCOND). The actual delay
needed is function of number of contending cores as well as the unrelated
coherency traffic from other cores. To keep the code simple, start off with
small delay of 1 which would suffice most cases and in case of contention
double the delay. Eventually the delay is sufficient such that the coherency
pipeline is drained, thus a subsequent exclusive access would succeed.
Link: http://lkml.kernel.org/r/1438612568-28265-1-git-send-email-vgupta@synopsys.com
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
With HS 2.1 release, the peripheral space register no longer contains
the uncached space specifics, causing the kernel to panic early on.
So read the newer NON VOLATILE AUX register to get that info.
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
The irq argument of most interrupt flow handlers is unused or merily
used instead of a local variable. The handlers which need the irq
argument can retrieve the irq number from the irq descriptor.
Search and update was done with coccinelle and the invaluable help of
Julia Lawall.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Julia Lawall <Julia.Lawall@lip6.fr>
Cc: Vineet Gupta <vgupta@synopsys.com>
Migrate arc driver to the new 'set-state' interface provided by
clockevents core, the earlier 'set-mode' interface is marked obsolete
now.
This also enables us to implement callbacks for new states of clockevent
devices, for example: ONESHOT_STOPPED.
Cc: Vineet Gupta <vgupta@synopsys.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
The IRQCHIP_DECLARE macro migrated to 'include/linux/irqchip.h'.
See commit 91e20b5040
("irqchip: Move IRQCHIP_DECLARE macro to include/linux/irqchip.h").
This patch removes the inclusions of private header 'drivers/irqchip/irqchip.h'
and if necessary replaces them with inclusions of 'include/linux/irqchip.h'.
Signed-off-by: Joel Porquet <joel@porquet.org>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
With this nsim standlone / OSCI have working irq affinity - AXS103 still
needs some work as IDU is not visible in intc hierarchy yet !
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Pull more vfs updates from Al Viro:
"Assorted VFS fixes and related cleanups (IMO the most interesting in
that part are f_path-related things and Eric's descriptor-related
stuff). UFS regression fixes (it got broken last cycle). 9P fixes.
fs-cache series, DAX patches, Jan's file_remove_suid() work"
[ I'd say this is much more than "fixes and related cleanups". The
file_table locking rule change by Eric Dumazet is a rather big and
fundamental update even if the patch isn't huge. - Linus ]
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (49 commits)
9p: cope with bogus responses from server in p9_client_{read,write}
p9_client_write(): avoid double p9_free_req()
9p: forgetting to cancel request on interrupted zero-copy RPC
dax: bdev_direct_access() may sleep
block: Add support for DAX reads/writes to block devices
dax: Use copy_from_iter_nocache
dax: Add block size note to documentation
fs/file.c: __fget() and dup2() atomicity rules
fs/file.c: don't acquire files->file_lock in fd_install()
fs:super:get_anon_bdev: fix race condition could cause dev exceed its upper limitation
vfs: avoid creation of inode number 0 in get_next_ino
namei: make set_root_rcu() return void
make simple_positive() public
ufs: use dir_pages instead of ufs_dir_pages()
pagemap.h: move dir_pages() over there
remove the pointless include of lglock.h
fs: cleanup slight list_entry abuse
xfs: Correctly lock inode when removing suid and file capabilities
fs: Call security_ops->inode_killpriv on truncate
fs: Provide function telling whether file_remove_privs() will do anything
...
- CONFIG_ARC_UBOOT_SUPPORT to handle arguments passed in r0, r1, r2
- CONFIG_DEVTMPFS_MOUNT for mouting rootfs since it uses external cpio
for rootfs
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: devicetree@vger.kernel.org
Signed-off-by: Ruud Derwig <rderwig@synopsys.com>
[vgupta: folded the Main baord DT files for smp/up into one]
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
This allows platforms to provide their own cpu wakeup routines
as well as IPI send / clear backends, while allowing a SMP kernel w/o
any such backend to build/boot
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Reported by Anton as LTP:munmap01 failing with Illegal Instruction
Exception.
--------------------->8--------------------------------------
mmap2(NULL, 24576, PROT_READ|PROT_WRITE, MAP_SHARED, 3, 0) = 0x200d2000
munmap(0x200d2000, 24576) = 0
--- SIGSEGV {si_signo=SIGSEGV, si_code=SEGV_MAPERR, si_addr=0x200d2000}
---
potentially unexpected fatal signal 4.
Path: /munmap01
CPU: 0 PID: 61 Comm: munmap01 Not tainted 3.13.0-g5d5c46d9a556 #8
task: 9f1a8000 ti: 9f154000 task.ti: 9f154000
[ECR ]: 0x00020100 => Illegal Insn
[EFA ]: 0x0001354c
[BLINK ]: 0x200515d4
[ERET ]: 0x1354c
@off 0x1354c in [/munmap01]
VMA: 0x00010000 to 0x00018000
[STAT32]: 0x800802c0
...
--------------------->8--------------------------------------
The issue was
1. munmap01 accessed unmapped memory (on purpose) with signal handler
installed for SIGSEGV
2. The faulting instruction happened to be in Delay Slot
00011864 <main>:
11908: bl.d 13284 <tst_resm>
1190c: stb r16,[r2]
3. kernel sets up the reg file for signal handler and correctly clears
the DE bit in pt_regs->status32 placeholder
4. However RESTORE_CALLEE_SAVED_USER macro is not adjusted for ARCv2,
and it over-writes the above with orig/stale value of status32
5. After RTIE, userspace signal handler executes a non branch
instruction with DE bit set, triggering Illegal Instruction Exception.
Reported-by: Anton Kolesov <akolesov@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
These have been register compatible so far. However ARCv2 mandates
different pt_regs layout (due to h/w auto save). To keep pt_regs same
for both, we start by removing the assumption - used mainly for block
copies between the 2 structs in signal handling and ptrace
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Returning from pure kernel mode and exception mode use the same code
anyways. Remove one the duplicate blocks
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Elide the need to re-read ECR in Trap handler by ensuring that
EXCEPTION_PROLOGUE does that at the very end just before returning
to Trap handler
ARCv2 EXCEPTION_PROLOGUE already did that, so same for ARcompact and the
common trap handler adjusted to use cached ECR
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
This fixes the possible link/relo errors, since restore_regs will be
provided by ISA code, but called from ARC common code.
The .L prefix reassures binutils that it will be in same compilation
unit.
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Earlycon calculates UART clock as "BASE_BAUD * 16". In case of ARC
"BASE_BAUD" is calculated dynamically in runtime, basically it is an
alias to arc_early_base_baud(), which in turn just does
"arc_base_baud/16".
8250 UART on AXS/SDP board uses 33.3MHz clock source which is set in
"arc_base_baud" with this change.
Additional compatibility string "snps,arc-sdp" is introduced as well
because there're different flavours of AXS boards but they all share the
same motherboard and so it's possible to re-use the same code for
motherbord even if CPU daughterboard changes.
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Currently, it doesn't invoke the callback but continues to unwind
Also while at it - simplify the code a bit
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Directly return the result of perf_pmu_register() in
arc_pmu_device_probe() instead of assigning and returning variable ret.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
static arc_pmu in the arch/arc/kernel/perf_event.c is not initialized as
it's shadowed by a local variable of the same name in the
arc_pmu_device_probe.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Fixes: 03c94fcf95 "ARC: perf: make @arc_pmu static global"
CC: <stable@vger.kernel.org> # 4.1
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
print_task_path_n_nm() is local to this file, its only user being
show_regs(). Mark the function static and avoid the EXPORT_SYMBOL.
Signed-off-by: Davidlohr Bueso <dbueso@suse.de>
Acked-by: Vineet Gupta <vgupta@synoipsys.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull exec domain removal from Richard Weinberger:
"This series removes execution domain support from Linux.
The idea behind exec domains was to support different ABIs. The
feature was never complete nor stable. Let's rip it out and make the
kernel signal handling code less complicated"
* 'exec_domain_rip_v2' of git://git.kernel.org/pub/scm/linux/kernel/git/rw/misc: (27 commits)
arm64: Removed unused variable
sparc: Fix execution domain removal
Remove rest of exec domains.
arch: Remove exec_domain from remaining archs
arc: Remove signal translation and exec_domain
xtensa: Remove signal translation and exec_domain
xtensa: Autogenerate offsets in struct thread_info
x86: Remove signal translation and exec_domain
unicore32: Remove signal translation and exec_domain
um: Remove signal translation and exec_domain
tile: Remove signal translation and exec_domain
sparc: Remove signal translation and exec_domain
sh: Remove signal translation and exec_domain
s390: Remove signal translation and exec_domain
mn10300: Remove signal translation and exec_domain
microblaze: Remove signal translation and exec_domain
m68k: Remove signal translation and exec_domain
m32r: Remove signal translation and exec_domain
m32r: Autogenerate offsets in struct thread_info
frv: Remove signal translation and exec_domain
...
Pull vfs update from Al Viro:
"Part one:
- struct filename-related cleanups
- saner iov_iter_init() replacements (and switching the syscalls to
use of those)
- ntfs switch to ->write_iter() (Anton)
- aio cleanups and splitting iocb into common and async parts
(Christoph)
- assorted fixes (me, bfields, Andrew Elble)
There's a lot more, including the completion of switchover to
->{read,write}_iter(), d_inode/d_backing_inode annotations, f_flags
race fixes, etc, but that goes after #for-davem merge. David has
pulled it, and once it's in I'll send the next vfs pull request"
* 'for-linus-1' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (35 commits)
sg_start_req(): use import_iovec()
sg_start_req(): make sure that there's not too many elements in iovec
blk_rq_map_user(): use import_single_range()
sg_io(): use import_iovec()
process_vm_access: switch to {compat_,}import_iovec()
switch keyctl_instantiate_key_common() to iov_iter
switch {compat_,}do_readv_writev() to {compat_,}import_iovec()
aio_setup_vectored_rw(): switch to {compat_,}import_iovec()
vmsplice_to_user(): switch to import_iovec()
kill aio_setup_single_vector()
aio: simplify arguments of aio_setup_..._rw()
aio: lift iov_iter_init() into aio_setup_..._rw()
lift iov_iter into {compat_,}do_readv_writev()
NFS: fix BUG() crash in notify_change() with patch to chown_common()
dcache: return -ESTALE not -EBUSY on distributed fs race
NTFS: Version 2.1.32 - Update file write from aio_write to write_iter.
VFS: Add iov_iter_fault_in_multipages_readable()
drop bogus check in file_open_root()
switch security_inode_getattr() to struct path *
constify tomoyo_realpath_from_path()
...
Pull trivial tree from Jiri Kosina:
"Usual trivial tree updates. Nothing outstanding -- mostly printk()
and comment fixes and unused identifier removals"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial:
goldfish: goldfish_tty_probe() is not using 'i' any more
powerpc: Fix comment in smu.h
qla2xxx: Fix printks in ql_log message
lib: correct link to the original source for div64_u64
si2168, tda10071, m88ds3103: Fix firmware wording
usb: storage: Fix printk in isd200_log_config()
qla2xxx: Fix printk in qla25xx_setup_mode
init/main: fix reset_device comment
ipwireless: missing assignment
goldfish: remove unreachable line of code
coredump: Fix do_coredump() comment
stacktrace.h: remove duplicate declaration task_struct
smpboot.h: Remove unused function prototype
treewide: Fix typo in printk messages
treewide: Fix typo in printk messages
mod_devicetable: fix comment for match_flags
As execution domain support is gone we can remove
signal translation from the signal code and remove
exec_domain from thread_info.
Signed-off-by: Richard Weinberger <richard@nod.at>
flush_old_exec() has already done that. Back on 2011 a bunch of
instances like that had been kicked out, but that hadn't taken
care of then-out-of-tree architectures, obviously, and they served
as reinfection vector...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
The 'arg' argument to copy_thread() is only ever used when forking a new
kernel thread. Hence, rename it to 'kthread_arg' for clarity.
Signed-off-by: Alex Dowad <alexinbeijing@gmail.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
A malicious signal handler / restorer can DOS the system by fudging the
user regs saved on stack, causing weird things such as sigreturn returning
to user mode PC but cpu state still being kernel mode....
Ensure that in sigreturn path status32 always has U bit; any other bogosity
(gargbage PC etc) will be taken care of by normal user mode exceptions mechanisms.
Reproducer signal handler:
void handle_sig(int signo, siginfo_t *info, void *context)
{
ucontext_t *uc = context;
struct user_regs_struct *regs = &(uc->uc_mcontext.regs);
regs->scratch.status32 = 0;
}
Before the fix, kernel would go off to weeds like below:
--------->8-----------
[ARCLinux]$ ./signal-test
Path: /signal-test
CPU: 0 PID: 61 Comm: signal-test Not tainted 4.0.0-rc5+ #65
task: 8f177880 ti: 5ffe6000 task.ti: 8f15c000
[ECR ]: 0x00220200 => Invalid Write @ 0x00000010 by insn @ 0x00010698
[EFA ]: 0x00000010
[BLINK ]: 0x2007c1ee
[ERET ]: 0x10698
[STAT32]: 0x00000000 : <--------
BTA: 0x00010680 SP: 0x5ffe7e48 FP: 0x00000000
LPS: 0x20003c6c LPE: 0x20003c70 LPC: 0x00000000
...
--------->8-----------
Reported-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
The regfile provided to SA_SIGINFO signal handler as ucontext was off by
one due to pt_regs gutter cleanups in 2013.
Before handling signal, user pt_regs are copied onto user_regs_struct and copied
back later. Both structs are binary compatible. This was all fine until
commit 2fa919045b (ARC: pt_regs update #2) which removed the empty stack slot
at top of pt_regs (corresponding to first pad) and made the corresponding
fixup in struct user_regs_struct (the pad in there was moved out of
@scratch - not removed altogether as it is part of ptrace ABI)
struct user_regs_struct {
+ long pad;
struct {
- long pad;
long bta, lp_start, lp_end,....
} scratch;
...
}
This meant that now user_regs_struct was off by 1 reg w.r.t pt_regs and
signal code needs to user_regs_struct.scratch to reflect it as pt_regs,
which is what this commit does.
This problem was hidden for 2 years, because both save/restore, despite
using wrong location, were using the same location. Only an interim
inspection (reproducer below) exposed the issue.
void handle_segv(int signo, siginfo_t *info, void *context)
{
ucontext_t *uc = context;
struct user_regs_struct *regs = &(uc->uc_mcontext.regs);
printf("regs %x %x\n", <=== prints 7 8 (vs. 8 9)
regs->scratch.r8, regs->scratch.r9);
}
int main()
{
struct sigaction sa;
sa.sa_sigaction = handle_segv;
sa.sa_flags = SA_SIGINFO;
sigemptyset(&sa.sa_mask);
sigaction(SIGSEGV, &sa, NULL);
asm volatile(
"mov r7, 7 \n"
"mov r8, 8 \n"
"mov r9, 9 \n"
"mov r10, 10 \n"
:::"r7","r8","r9","r10");
*((unsigned int*)0x10) = 0;
}
Fixes: 2fa919045b "ARC: pt_regs update #2: Remove unused gutter at start of pt_regs"
CC: <stable@vger.kernel.org>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
The old implementation assumed that SP at the time of __switch_to() is
right above pt_regs which is almost certainly not the case as there will
be some stack build up between entry into kernel and leading up to
__switch_to
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
/proc/<pid>/maps currently don't annotate stack vma with "[stack]"
This is because KSTK_ESP ie expected to return usermode SP of tsk while
currently it returns the kernel mode SP of a sleeping tsk.
While the fix is trivial, we also need to adjust the ARC kernel stack
unwinder to not use KSTK_SP and friends any more.
Cc: <stable@vger.kernel.org>
Reported-and-suggested-by: Alexey Brodkin <abrodkin@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
The arc unwinder can also be used for perf callchains.
Signed-off-by: Mischa Jonker <mjonker@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Some fixes, nothing too exciting this time as well...
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=8o17
-----END PGP SIGNATURE-----
Merge tag 'arc-3.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc
Pull ARC updates from Vineet Gupta:
"Some fixes, nothing too exciting this time as well..."
* tag 'arc-3.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc:
ARC: fix page address calculation if PAGE_OFFSET != LINUX_LINK_BASE
ARC: Fix earlycon build breakage
ARC: Dynamically determine BASE_BAUD from DeviceTree
arc: Remove unused prepare_to_copy()
ARC: use ACCESS_ONCE in cmpxchg loop
ARC: add some more comments to ret_from_fork
ARC: fix /proc/cpuinfo for offline cpus
If an attacker can cause a controlled kernel stack overflow, overwriting
the restart block is a very juicy exploit target. This is because the
restart_block is held in the same memory allocation as the kernel stack.
Moving the restart block to struct task_struct prevents this exploit by
making the restart_block harder to locate.
Note that there are other fields in thread_info that are also easy
targets, at least on some architectures.
It's also a decent simplification, since the restart code is more or less
identical on all architectures.
[james.hogan@imgtec.com: metag: align thread_info::supervisor_stack]
Signed-off-by: Andy Lutomirski <luto@amacapital.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Kees Cook <keescook@chromium.org>
Cc: David Miller <davem@davemloft.net>
Acked-by: Richard Weinberger <richard@nod.at>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Haavard Skinnemoen <hskinnemoen@gmail.com>
Cc: Hans-Christian Egtvedt <egtvedt@samfundet.no>
Cc: Steven Miao <realmz6@gmail.com>
Cc: Mark Salter <msalter@redhat.com>
Cc: Aurelien Jacquiot <a-jacquiot@ti.com>
Cc: Mikael Starvik <starvik@axis.com>
Cc: Jesper Nilsson <jesper.nilsson@axis.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Richard Kuo <rkuo@codeaurora.org>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Jonas Bonn <jonas@southpole.se>
Cc: "James E.J. Bottomley" <jejb@parisc-linux.org>
Cc: Helge Deller <deller@gmx.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Acked-by: Michael Ellerman <mpe@ellerman.id.au> (powerpc)
Tested-by: Michael Ellerman <mpe@ellerman.id.au> (powerpc)
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Chen Liqin <liqin.linux@gmail.com>
Cc: Lennox Wu <lennox.wu@gmail.com>
Cc: Chris Metcalf <cmetcalf@ezchip.com>
Cc: Guan Xuetao <gxt@mprc.pku.edu.cn>
Cc: Chris Zankel <chris@zankel.net>
Cc: Max Filippov <jcmvbkbc@gmail.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit ffb7fcd66f ("ARC: Dynamically determine BASE_BAUD from DeviceTree")
breaks arc:defconfig build:
drivers/built-in.o: In function `of_setup_earlycon':
(.init.text+0xb3e): undefined reference to `arc_early_base_baud'
drivers/built-in.o: In function `setup_earlycon':
(.init.text+0xcd0): undefined reference to `arc_early_base_baud'
make: *** [vmlinux] Error 1
BASE_BAUD is only required for earlycon, which should depend on
CONFIG_SERIAL_EARLYCON.
Reported-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Yuriy Kolerov