On older arc700 cores, some of the features configured were not present
in Build config registers. To print about them at boot, we just use the
Kconfig option i.e. whether linux is built to use them or not.
So yes this seems bogus, but what else can be done. Moreover if linux is
booting with these enabled, then the Kconfig info is a good indicator
anyways.
Over time these "hacks" accumulated in read_arc_build_cfg_regs() as well
as arc_cpu_mumbojumbo(). so refactor and move all of those in a single
place: read_arc_build_cfg_regs(). This causes some code redcution too:
| bloat-o-meter2 arch/arc/kernel/setup.o.0 arch/arc/kernel/setup.o.1
| add/remove: 0/0 grow/shrink: 2/1 up/down: 64/-132 (-68)
| function old new delta
| setup_processor 610 670 +60
| cpuinfo_arc700 76 80 +4
| arc_cpu_mumbojumbo 752 620 -132
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Previously we would not print the case when IOC existed but was not
enabled.
And while at it, reduce one line off boot printing by consolidating
the Peripheral address space and IO-Coherency which in a way
applies to them
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Its all generic atomic_long_t stuff now.
Tested-by: Jason Low <jason.low2@hpe.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-arch@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
if user disables IOC from debugger at startup (by clearing @ioc_enable),
@ioc_exists is cleared too. This means boot prints don't capture the
fact that IOC was present but disabled which could be misleading.
So invert how we use @ioc_enable and @ioc_exists and make it more
canonical. @ioc_exists represent whether hardware is present or not and
stays same whether enabled or not. @ioc_enable is still user driven,
but will be auto-disabled if IOC hardware is not present, i.e. if
@ioc_exist=0. This is opposite to what we were doing before, but much
clearer.
This means @ioc_enable is now the "exported" toggle in rest of code such
as dma mapping API.
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Older ARC700 cores (ARC750 specifically) lack instructions to implement
atomic r-w-w. This is problematic for userspace libraries such as NPTL
which need atomic primitives. So enable them by providing kernel assist.
This is costly but really the only sane soluton (othern than tight
spinning using the otherwise availiable atomic exchange EX instruciton).
Good thing is there are only a few of these cores running Linux out in
the wild.
This only works on UP systems.
Reviewed-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
The cast valid since TASK_SIZE * 2 will never actually cause overflow.
| CC fs/binfmt_elf.o
| In file included from ../include/linux/elf.h:4:0,
| from ../include/linux/module.h:15,
| from ../fs/binfmt_elf.c:12:
| ../fs/binfmt_elf.c: In function load_elf_binar:
| ../arch/arc/include/asm/elf.h:57:29: warning: integer overflow in expression [-Woverflow]
| #define ELF_ET_DYN_BASE (2 * TASK_SIZE / 3)
| ^
| ../fs/binfmt_elf.c:921:16: note: in expansion of macro ELF_ET_DYN_BASE
| load_bias = ELF_ET_DYN_BASE - vaddr;
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
The IDU intc is technically part of MCIP (Multi-core IP) hence
historically was only available in a SMP hardware build (and thus only
in a SMP kernel build). Now that hardware restriction has been lifted,
so a UP kernel needs to support it.
This requires breaking mcip.c into parts which are strictly SMP
(inter-core interrupts) and IDU which in reality is just another
intc and thus has no bearing on SMP.
This change allows IDU in UP builds and with a suitable device tree, we
can have the cascaded intc system
ARCv2 core intc <---> ARCv2 IDU intc <---> periperals
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Commit d9676fa152 ("ARCv2: Enable LOCKDEP"), changed
local_save_flags() to not return raw STATUS32 but encoded in the form
such that it could be fed directly to CLRI/SETI instructions.
However the STATUS32.E[] was not captured correctly as it corresponds to
bits [4:1] in the register and not [3:0]
Fixes: d9676fa152 ("ARCv2: Enable LOCKDEP")
Cc: Evgeny Voevodin <evgeny.voevodin@intel.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
1. detect whether binutils supports the cfi pseudo ops
2. define conditional macros to generate the ops
3. define new ENTRY_CFI/END_CFI to annotate hand asm code.
- Needed because we don't want to emit dwarf info in general ENTRY/END
used by lowest level trap/exception/interrutp handlers as unwinder
gets confused trying to unwind out of them. We want unwinder to
instead stop when it hits onfo those routines
- These provide minimal start/end cfi ops assuming routine doesn't
touch stack memory/regs
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
We used to live with PERF_COUNT_HW_CACHE_REFERENCES and
PERF_COUNT_HW_CACHE_REFERENCES not specified on ARC.
Those events are actually aliases to 2 cache events that we do support
and so this change sets "cache-reference" and "cache-misses" events
in the same way as "L1-dcache-loads" and L1-dcache-load-misses.
And while at it adding debug info for cache events as well as doing a
subtle fix in HW events debug info - config value is much better
represented by hex so we may see not only event index but as well other
control bits set (if they exist).
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-snps-arc@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Build brekeage since last changes to generic atomic operations.
Added couple of missing macros which are now mandatory
Signed-off-by: Noam Camus <noamca@mellanox.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
ARCv2 ISA provides 64-bit exclusive load/stores so use them to implement
the 64-bit atomics and elide the spinlock based generic 64-bit atomics
boot tested with atomic64 self-test (and GOD bless the person who wrote
them, I realized my inline assmebly is sloppy as hell)
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Will Deacon <will.deacon@arm.com>
Cc: linux-snps-arc@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
HS release 3.0 provides for even more flexibility in specifying the
volatile address space for mapping peripherals.
With HS 2.1 @start was made flexible / programmable - with HS 3.0 even
@end can be setup (vs. fixed to 0xFFFF_FFFF before).
So add code to reflect that and while at it remove an unused struct
defintion
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Pull uaccess fixes from Al Viro:
"Fixes for broken uaccess primitives - mostly lack of proper zeroing
in copy_from_user()/get_user()/__get_user(), but for several
architectures there's more (broken clear_user() on frv and
strncpy_from_user() on hexagon)"
* 'uaccess-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (28 commits)
avr32: fix copy_from_user()
microblaze: fix __get_user()
microblaze: fix copy_from_user()
m32r: fix __get_user()
blackfin: fix copy_from_user()
sparc32: fix copy_from_user()
sh: fix copy_from_user()
sh64: failing __get_user() should zero
score: fix copy_from_user() and friends
score: fix __get_user/get_user
s390: get_user() should zero on failure
ppc32: fix copy_from_user()
parisc: fix copy_from_user()
openrisc: fix copy_from_user()
nios2: fix __get_user()
nios2: copy_from_user() should zero the tail of destination
mn10300: copy_from_user() should zero on access_ok() failure...
mn10300: failing __get_user() and get_user() should zero
mips: copy_from_user() must zero the destination on access_ok() failure
ARC: uaccess: get_user to zero out dest in cause of fault
...
Add ARC as an arch that supports PCI_MSI_IRQ_DOMAIN and add generation of
msi.h in the ARC arch.
Signed-off-by: Joao Pinto <jpinto@synopsys.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Vineet Gupta <vgupta@synopsys.com>
| CC mm/memory.o
| In file included from ../mm/memory.c:53:0:
| ../include/linux/pfn_t.h: In function ‘pfn_t_pte’:
| ../include/linux/pfn_t.h:78:2: error: conversion to non-scalar type requested
| return pfn_pte(pfn_t_to_pfn(pfn), pgprot);
With STRICT_MM_TYPECHECKS pte_t is a struct and the offending code
forces a cast which ends up shifting a struct and hence the gcc warning.
Note that in recent past some of the arches (aarch64, s390) made
STRICT_MM_TYPECHECKS default, but we don't for ARC as this leads to slightly
worse generated code, given ARC ABI definition of returning structs
(which pte_t would become)
Quoting from ARC ABI...
"Results of type struct are returned in a caller-supplied temporary
variable whose address is passed in r0.
For such functions, the arguments are shifted so that they are
passed in r1 and up."
So
- struct to be returned would be allocated on stack requiring extra
code at call sites
- callee updates stack memory to facilitate the return (vs. simple
MOV into return reg r0)
Hence STRICT_MM_TYPECHECKS is not enabled by default for ARC
Cc: <stable@vger.kernel.org> #4.4+
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
The syscall ABI includes the gcc functional calling ABI since a syscall
implies userland caller and kernel callee.
The current gcc ABI (v3) for ARCv2 ISA required 64-bit data be passed in
even-odd register pairs, (potentially punching reg holes when passing such
values as args). This was partly driven by the fact that the double-word
LDD/STD instructions in ARCv2 expect the register alignment and thus gcc
forcing this avoids extra MOV at the cost of a few unused register (which we
have plenty anyways).
This however was rejected as part of upstreaming gcc port to HS. So the new
ABI v4 doesn't enforce the even-odd reg restriction.
Do note that for ARCompact ISA builds v3 and v4 are practically the same in
terms of gcc code generation.
In terms of change management, we infer the new ABI if gcc 6.x onwards
is used for building the kernel.
This also needs a stable backport to enable older kernels to work with
new tools/user-space
Cc: <stable@vger.kernel.org>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
User mode callee regs are explicitly collected before signal delivery or
breakpoint trap. r25 is special for kernel as it serves as task pointer,
so user mode value is clobbered very early. It is saved in pt_regs where
generally only scratch (aka caller saved) regs are saved.
The code to access the corresponding pt_regs location had a subtle bug as
it was using load/store with scaling of offset, whereas the offset was already
byte wise correct. So fix this by replacing LD.AS with a standard LD
Cc: <stable@vger.kernel.org>
Signed-off-by: Liav Rehana <liavr@mellanox.com>
Reviewed-by: Alexey Brodkin <abrodkin@synopsys.com>
[vgupta: rewrote title and commit log]
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
trace_hardirqs_on_caller() in lockdep.c expects to be called before, not
after interrupts are actually enabled.
The following comment in kernel/locking/lockdep.c substantiates this
claim:
"
/*
* We're enabling irqs and according to our state above irqs weren't
* already enabled, yet we find the hardware thinks they are in fact
* enabled.. someone messed up their IRQ state tracing.
*/
"
An example can be found in include/linux/irqflags.h:
do { trace_hardirqs_on(); raw_local_irq_enable(); } while (0)
Without this change, we hit the following DEBUG_LOCKS_WARN_ON.
[ 7.760000] ------------[ cut here ]------------
[ 7.760000] WARNING: CPU: 0 PID: 1 at kernel/locking/lockdep.c:2711 resume_user_mode_begin+0x48/0xf0
[ 7.770000] DEBUG_LOCKS_WARN_ON(!irqs_disabled())
[ 7.780000] Modules linked in:
[ 7.780000] CPU: 0 PID: 1 Comm: init Not tainted 4.7.0-00003-gc668bb9-dirty #366
[ 7.790000]
[ 7.790000] Stack Trace:
[ 7.790000] arc_unwind_core.constprop.1+0xa4/0x118
[ 7.800000] warn_slowpath_fmt+0x72/0x158
[ 7.800000] resume_user_mode_begin+0x48/0xf0
[ 7.810000] ---[ end trace 6f6a7a8fae20d2f0 ]---
Signed-off-by: Daniel Mentz <danielmentz@google.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Things have been calm here - nothing much except for a few fixes
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=/rhI
-----END PGP SIGNATURE-----
Merge tag 'arc-4.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc
Pull ARC updates from Vineet Gupta:
"Things have been calm here - nothing much except for a few fixes"
* tag 'arc-4.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc:
ARC: mm: don't loose PTE_SPECIAL in pte_modify()
ARC: dma: fix address translation in arc_dma_free
ARC: typo fix in mm/ioremap.c
ARC: fix linux-next build breakage
LTP madvise05 was generating mm splat
| [ARCLinux]# /sd/ltp/testcases/bin/madvise05
| BUG: Bad page map in process madvise05 pte:80e08211 pmd:9f7d4000
| page:9fdcfc90 count:1 mapcount:-1 mapping: (null) index:0x0 flags: 0x404(referenced|reserved)
| page dumped because: bad pte
| addr:200b8000 vm_flags:00000070 anon_vma: (null) mapping: (null) index:1005c
| file: (null) fault: (null) mmap: (null) readpage: (null)
| CPU: 2 PID: 6707 Comm: madvise05
And for newer kernels, the system was rendered unusable afterwards.
The problem was mprotect->pte_modify() clearing PTE_SPECIAL (which is
set to identify the special zero page wired to the pte).
When pte was finally unmapped, special casing for zero page was not
done, and instead it was treated as a "normal" page, tripping on the
map counts etc.
This fixes ARC STAR 9001053308
Cc: <stable@vger.kernel.org>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Pull locking updates from Ingo Molnar:
"The locking tree was busier in this cycle than the usual pattern - a
couple of major projects happened to coincide.
The main changes are:
- implement the atomic_fetch_{add,sub,and,or,xor}() API natively
across all SMP architectures (Peter Zijlstra)
- add atomic_fetch_{inc/dec}() as well, using the generic primitives
(Davidlohr Bueso)
- optimize various aspects of rwsems (Jason Low, Davidlohr Bueso,
Waiman Long)
- optimize smp_cond_load_acquire() on arm64 and implement LSE based
atomic{,64}_fetch_{add,sub,and,andnot,or,xor}{,_relaxed,_acquire,_release}()
on arm64 (Will Deacon)
- introduce smp_acquire__after_ctrl_dep() and fix various barrier
mis-uses and bugs (Peter Zijlstra)
- after discovering ancient spin_unlock_wait() barrier bugs in its
implementation and usage, strengthen its semantics and update/fix
usage sites (Peter Zijlstra)
- optimize mutex_trylock() fastpath (Peter Zijlstra)
- ... misc fixes and cleanups"
* 'locking-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (67 commits)
locking/atomic: Introduce inc/dec variants for the atomic_fetch_$op() API
locking/barriers, arch/arm64: Implement LDXR+WFE based smp_cond_load_acquire()
locking/static_keys: Fix non static symbol Sparse warning
locking/qspinlock: Use __this_cpu_dec() instead of full-blown this_cpu_dec()
locking/atomic, arch/tile: Fix tilepro build
locking/atomic, arch/m68k: Remove comment
locking/atomic, arch/arc: Fix build
locking/Documentation: Clarify limited control-dependency scope
locking/atomic, arch/rwsem: Employ atomic_long_fetch_add()
locking/atomic, arch/qrwlock: Employ atomic_fetch_add_acquire()
locking/atomic, arch/mips: Convert to _relaxed atomics
locking/atomic, arch/alpha: Convert to _relaxed atomics
locking/atomic: Remove the deprecated atomic_{set,clear}_mask() functions
locking/atomic: Remove linux/atomic.h:atomic_fetch_or()
locking/atomic: Implement atomic{,64,_long}_fetch_{add,sub,and,andnot,or,xor}{,_relaxed,_acquire,_release}()
locking/atomic: Fix atomic64_relaxed() bits
locking/atomic, arch/xtensa: Implement atomic_fetch_{add,sub,and,or,xor}()
locking/atomic, arch/x86: Implement atomic{,64}_fetch_{add,sub,and,or,xor}()
locking/atomic, arch/tile: Implement atomic{,64}_fetch_{add,sub,and,or,xor}()
locking/atomic, arch/sparc: Implement atomic{,64}_fetch_{add,sub,and,or,xor}()
...
__GFP_REPEAT has a rather weak semantic but since it has been introduced
around 2.6.12 it has been ignored for low order allocations.
pte_alloc_one_kernel uses __get_order_pte but this is obviously always
zero because BITS_FOR_PTE is not larger than 9 yet the page size is
always larger than 4K. This means that this flag has never been
actually useful here because it has always been used only for
PAGE_ALLOC_COSTLY requests.
Link: http://lkml.kernel.org/r/1464599699-30131-7-git-send-email-mhocko@kernel.org
Signed-off-by: Michal Hocko <mhocko@suse.com>
Acked-by: Vineet Gupta <vgupta@synopsys.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Since all architectures have this implemented now natively, remove this
dead code.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-arch@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Implement FETCH-OP atomic primitives, these are very similar to the
existing OP-RETURN primitives we already have, except they return the
value of the atomic variable _before_ modification.
This is especially useful for irreversible operations -- such as
bitops (because it becomes impossible to reconstruct the state prior
to modification).
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Vineet Gupta <vgupta@synopsys.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Noam Camus <noamc@ezchip.com>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-arch@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: linux-snps-arc@lists.infradead.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
This patch updates/fixes all spin_unlock_wait() implementations.
The update is in semantics; where it previously was only a control
dependency, we now upgrade to a full load-acquire to match the
store-release from the spin_unlock() we waited on. This ensures that
when spin_unlock_wait() returns, we're guaranteed to observe the full
critical section we waited on.
This fixes a number of spin_unlock_wait() users that (not
unreasonably) rely on this.
I also fixed a number of ticket lock versions to only wait on the
current lock holder, instead of for a full unlock, as this is
sufficient.
Furthermore; again for ticket locks; I added an smp_rmb() in between
the initial ticket load and the spin loop testing the current value
because I could not convince myself the address dependency is
sufficient, esp. if the loads are of different sizes.
I'm more than happy to remove this smp_rmb() again if people are
certain the address dependency does indeed work as expected.
Note: PPC32 will be fixed independently
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: chris@zankel.net
Cc: cmetcalf@mellanox.com
Cc: davem@davemloft.net
Cc: dhowells@redhat.com
Cc: james.hogan@imgtec.com
Cc: jejb@parisc-linux.org
Cc: linux@armlinux.org.uk
Cc: mpe@ellerman.id.au
Cc: ralf@linux-mips.org
Cc: realmz6@gmail.com
Cc: rkuo@codeaurora.org
Cc: rth@twiddle.net
Cc: schwidefsky@de.ibm.com
Cc: tony.luck@intel.com
Cc: vgupta@synopsys.com
Cc: ysato@users.sourceforge.jp
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
This reverts commit e78fdfef84.
The issue was fixed in hardware in HS2.1C release and there are no known
external users of affected RTL so revert the whole delayed retry series !
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
This reverts commit b89aa12c17.
The issue was fixed in hardware in HS2.1C release and there are no known
external users of affected RTL so revert the whole delayed retry series !
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
This reverts commit 1097163870.
The issue was fixed in hardware in HS2.1C release and there are no known
external users of affected RTL - so revert thw whole delayed retry
series !
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
I have only one patch for asm-generic in this release, this one is from
James Hogan and updates the generic system call table for renameat2
so we don't need to provide both renameat and renameat2 in newly
added architectures.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=ae81
-----END PGP SIGNATURE-----
Merge tag 'asm-generic-4.7' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic
Pull asm-generic cleanup from Arnd Bergmann:
"I have only one patch for asm-generic in this release, this one is
from James Hogan and updates the generic system call table for
renameat2 so we don't need to provide both renameat and renameat2 in
newly added architectures"
* tag 'asm-generic-4.7' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic:
asm-generic: Drop renameat syscall from default list
Merge updates from Andrew Morton:
- fsnotify fix
- poll() timeout fix
- a few scripts/ tweaks
- debugobjects updates
- the (small) ocfs2 queue
- Minor fixes to kernel/padata.c
- Maybe half of the MM queue
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (117 commits)
mm, page_alloc: restore the original nodemask if the fast path allocation failed
mm, page_alloc: uninline the bad page part of check_new_page()
mm, page_alloc: don't duplicate code in free_pcp_prepare
mm, page_alloc: defer debugging checks of pages allocated from the PCP
mm, page_alloc: defer debugging checks of freed pages until a PCP drain
cpuset: use static key better and convert to new API
mm, page_alloc: inline pageblock lookup in page free fast paths
mm, page_alloc: remove unnecessary variable from free_pcppages_bulk
mm, page_alloc: pull out side effects from free_pages_check
mm, page_alloc: un-inline the bad part of free_pages_check
mm, page_alloc: check multiple page fields with a single branch
mm, page_alloc: remove field from alloc_context
mm, page_alloc: avoid looking up the first zone in a zonelist twice
mm, page_alloc: shortcut watermark checks for order-0 pages
mm, page_alloc: reduce cost of fair zone allocation policy retry
mm, page_alloc: shorten the page allocator fast path
mm, page_alloc: check once if a zone has isolated pageblocks
mm, page_alloc: move __GFP_HARDWALL modifications out of the fastpath
mm, page_alloc: simplify last cpupid reset
mm, page_alloc: remove unnecessary initialisation from __alloc_pages_nodemask()
...
I've just discovered that the useful-sounding has_transparent_hugepage()
is actually an architecture-dependent minefield: on some arches it only
builds if CONFIG_TRANSPARENT_HUGEPAGE=y, on others it's also there when
not, but on some of those (arm and arm64) it then gives the wrong
answer; and on mips alone it's marked __init, which would crash if
called later (but so far it has not been called later).
Straighten this out: make it available to all configs, with a sensible
default in asm-generic/pgtable.h, removing its definitions from those
arches (arc, arm, arm64, sparc, tile) which are served by the default,
adding #define has_transparent_hugepage has_transparent_hugepage to
those (mips, powerpc, s390, x86) which need to override the default at
runtime, and removing the __init from mips (but maybe that kind of code
should be avoided after init: set a static variable the first time it's
called).
Signed-off-by: Hugh Dickins <hughd@google.com>
Cc: "Kirill A. Shutemov" <kirill.shutemov@linux.intel.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Andres Lagar-Cavilla <andreslc@google.com>
Cc: Yang Shi <yang.shi@linaro.org>
Cc: Ning Qu <quning@gmail.com>
Cc: Mel Gorman <mgorman@techsingularity.net>
Cc: Konstantin Khlebnikov <koct9i@gmail.com>
Acked-by: David S. Miller <davem@davemloft.net>
Acked-by: Vineet Gupta <vgupta@synopsys.com> [arch/arc]
Acked-by: Gerald Schaefer <gerald.schaefer@de.ibm.com> [arch/s390]
Acked-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The default 256 bytes sometimes is just not enough.
We usually provide earlycon=... and console=... and ip=...
All this and more may need more room.
Signed-off-by: Noam Camus <noamc@ezchip.com>
Acked-by: Vineet Gupta <vgupta@synopsys.com>
Since the CTOP is SMT hardware multi-threaded, we need to hint
the HW that now will be a very good time to do a hardware
thread context switching. This is done by issuing the schd.rw
instruction (binary coded here so as to not require specific
revision of GCC to build the kernel).
sched.rw means that Thread becomes eligible for execution by
the threads scheduler after all pending read/write
transactions were completed.
Implementing cpu_relax_lowlatency() with barrier()
Since with current semantics of cpu_relax() it may take a
while till yielded CPU will get back.
Signed-off-by: Noam Camus <noamc@ezchip.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Acked-by: Vineet Gupta <vgupta@synopsys.com>
With generic "identity" num of CPUs is limited to 256 (8 bit).
We use our alternative AUX register GLOBAL_ID (12 bit).
Now we can support up to 4096 CPUs.
Signed-off-by: Noam Camus <noamc@ezchip.com>
NPS device got 256 cores and each got 16 HW threads (SMT).
We use EZchip dedicated ISA to trigger HW scheduler of the
core that current HW thread belongs to.
This scheduling makes sure that data beyond barrier is available
to all HW threads in core and by that to all in device (4K).
Signed-off-by: Noam Camus <noamc@ezchip.com>
Cc: Peter Zijlstra <peterz@infradead.org>
We need our own implementaions since we lack LLSC support.
Our extended ISA provided with optimized solution for all 32bit
operations we see in these three headers.
Signed-off-by: Noam Camus <noamc@ezchip.com>
NPS use special mapping right below TASK_SIZE.
Hence we need to lower STACK_TOP so that user stack won't
overlap NPS special mapping.
Signed-off-by: Noam Camus <noamc@ezchip.com>
Acked-by: Vineet Gupta <vgupta@synopsys.com>
If we hold rwlock and interrupt occures we may
end up spinning on it for ever during softirq.
Note that this lock is an internal lock
and since the lock is free to be used from any context,
the lock needs to be IRQ-safe.
Below you may see an example for interrupt we get while
nl_table_lock is holding its rw->lock_mutex and we spinned
on it for ever.
The concept for the fix was taken from SPARC.
[2015-05-12 19:16:12] Stack Trace:
[2015-05-12 19:16:12] arc_unwind_core+0xb8/0x11c
[2015-05-12 19:16:12] dump_stack+0x68/0xac
[2015-05-12 19:16:12] _raw_read_lock+0xa8/0xac
[2015-05-12 19:16:12] netlink_broadcast_filtered+0x56/0x35c
[2015-05-12 19:16:12] nlmsg_notify+0x42/0xa4
[2015-05-12 19:16:13] neigh_update+0x1fe/0x44c
[2015-05-12 19:16:13] neigh_event_ns+0x40/0xa4
[2015-05-12 19:16:13] arp_process+0x46e/0x5a8
[2015-05-12 19:16:13] __netif_receive_skb_core+0x358/0x500
[2015-05-12 19:16:13] process_backlog+0x92/0x154
[2015-05-12 19:16:13] net_rx_action+0xb8/0x188
[2015-05-12 19:16:13] __do_softirq+0xda/0x1d8
[2015-05-12 19:16:14] irq_exit+0x8a/0x8c
[2015-05-12 19:16:14] arch_do_IRQ+0x6c/0xa8
[2015-05-12 19:16:14] handle_interrupt_level1+0xe4/0xf0
Signed-off-by: Noam Camus <noamc@ezchip.com>
Acked-by: Peter Zijlstra <peterz@infradead.org>
On ARC, lower 2G of address space is translated and used for
- user vaddr space (region 0 to 5)
- unused kernel-user gutter (region 6)
- kernel vaddr space (region 7)
where each region simply represents 256MB of address space.
The kernel vaddr space of 256MB is used to implement vmalloc, modules
So far this was enough, but not on EZChip system with 4K CPUs (given
that per cpu mechanism uses vmalloc for allocating chunks)
So allow VMALLOC_SIZE to be configurable by expanding down into the unused
kernel-user gutter region which at default 256M was excessive anyways.
Also use _BITUL() to fix a build error since PGDIR_SIZE cannot use "1UL"
as called from assembly code in mm/tlbex.S
Signed-off-by: Noam Camus <noamc@ezchip.com>
[vgupta: rewrote changelog, debugged bootup crash due to int vs. hex]
Acked-by: Vineet Gupta <vgupta@synopsys.com>
UAPI header should not use Kconfig items
Use __BIG_ENDIAN__ defined as a compiler intrinsic
Signed-off-by: Noam Camus <noamc@ezchip.com>
[vgupta: fix changelog]
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
There are no more users of this - so RIP!
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
[vgupta: update changelog]
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
This will be needed for switching to linear irq domain as
irq_create_mapping() called by intr code needs the IRQ numbers
in addition to existing usage in mcip.c for requesting the irq
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
- timer frequency is derived from DT (no longer rely on top level
DT "clock-frequency" probed early and exported by asm/clk.h)
- TIMER0_IRQ need not be exported across arch code, confined to intc as
it is property of same
- Any failures in clockevent setup are considered pedantic and system
panic()'s as there is no generic fallback (unlike clocksource where
a jiffies based soft clocksource always exists)
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
ARC Timers so far have been handled as "legacy" w/o explicit description
in DT. This poses challenge for newer platforms wanting to use them.
This series will eventually help move timers over to DT.
This patch does a small change of using a CPU notifier to set clockevent
on non-boot CPUs. So explicit setup is done only on boot CPU (which will
later be done by DT)
Signed-off-by: Noam Camus <noamc@ezchip.com>
[vgupta: broken off from a bigger patch]
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
- The idea is to remove the API usage since it has a subltle
design flaw - relies on being called on cpu0 first. This is true for
some early per cpu irqs such as TIMER/IPI, but not for late probed
per cpu peripherals such a perf. And it's usage in perf has already
bitten us once: see c6317bc7c5
("ARCv2: perf: Ensure perf intr gets enabled on all cores") where we
ended up open coding it anyways
- The seeming duplication will go away once we start using cpu notifier
for timer setup
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Initial HIGHMEM support on ARC was introduced for PAE40 where the low
memory (0x8000_0000 based) and high memory (0x1_0000_0000) were
physically contiguous. So CONFIG_FLATMEM sufficed (despite a peipheral
hole in the middle, which wasted a bit of struct page memory, but things
worked).
However w/o PAE, highmem was not possible and we could only reach
~1.75GB of DDR. Now there is a use case to access ~4GB of DDR w/o PAE40
The idea is to have low memory at canonical 0x8000_0000 and highmem
at 0 so enire 4GB address space is available for physical addressing
This needs additional platform/interconnect mapping to convert
the non contiguous physical addresses into linear bus adresses.
From Linux point of view, non contiguous divide means FLATMEM no
longer works and DISCONTIGMEM is needed to track the pfns in the 2
regions.
This scheme would also work for PAE40, only better in that we don't
waste struct page memory for the peripheral hole.
The DT description will be something like
memory {
...
reg = <0x80000000 0x200000000 /* 512MB: lowmem */
0x00000000 0x10000000>; /* 256MB: highmem */
}
Signed-off-by: Noam Camus <noamc@ezchip.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
So a benign looking cleanup which macro'ized PAGE_SHIFT shifts turned
out to be bad (since it was done non-sensically across the board).
It caused boot failures with PAE40 as forced cast to (unsigned long)
from newly introduced virt_to_pfn() was causing truncatiion of the
(long long) pte/paddr values.
It is OK to use this in accessors dealing with kernel virtual address,
pointers etc, but not for PTE values themelves.
Fixes: cJ2ff5cf2735c ("ARC: mm: Use virt_to_pfn() for addr >> PAGE_SHIFT pattern)
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
While reviewing a different change to asm-generic/io.h Arnd spotted that
ARC ioread32 and ioread32be both of which come from asm-generic versions
are not symmetrical in terms of calling the io barriers.
generic ioread32 -> ARC readl() [ has barriers]
generic ioread32be -> __be32_to_cpu(__raw_readl()) [ lacks barriers]
While generic ioread32be is being remediated to call readl(), that involves
a swab32(), causing double swaps on ioread32be() on Big Endian systems.
So provide our versions of big endian IO accessors to ensure io barrier
calls while also keeping them optimal
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Cc: stable@vger.kernel.org [4.2+]
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
The newer renameat2 syscall provides all the functionality provided by
the renameat syscall and adds flags, so future architectures won't need
to include renameat.
Therefore drop the renameat syscall from the generic syscall list unless
__ARCH_WANT_RENAMEAT is defined by the architecture's unistd.h prior to
including asm-generic/unistd.h, and adjust all architectures using the
generic syscall list to define it so that no in-tree architectures are
affected.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Acked-by: Vineet Gupta <vgupta@synopsys.com>
Cc: linux-arch@vger.kernel.org
Cc: linux-snps-arc@lists.infradead.org
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: Mark Salter <msalter@redhat.com>
Cc: Aurelien Jacquiot <a-jacquiot@ti.com>
Cc: linux-c6x-dev@linux-c6x.org
Cc: Richard Kuo <rkuo@codeaurora.org>
Cc: linux-hexagon@vger.kernel.org
Cc: linux-metag@vger.kernel.org
Cc: Jonas Bonn <jonas@southpole.se>
Cc: linux@lists.openrisc.net
Cc: Chen Liqin <liqin.linux@gmail.com>
Cc: Lennox Wu <lennox.wu@gmail.com>
Cc: Chris Metcalf <cmetcalf@mellanox.com>
Cc: Guan Xuetao <gxt@mprc.pku.edu.cn>
Cc: Ley Foon Tan <lftan@altera.com>
Cc: nios2-dev@lists.rocketboards.org
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: uclinux-h8-devel@lists.sourceforge.jp
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- The asm helpers for calling into irq tracer were missing
- Add calls to above helpers in low level assembly entry code for ARCv2
- irq_save() uses CLRI to disable interrupts and returns the prev interrupt
state (in STATUS32) in a specific encoding (and not the raw value of
STATUS32). This is usable with SETI in irq_restore(). However
save_flags() reads the raw value of STATUS32 which doesn't pair with
irq_save/restore() and thus needs fixing.
Signed-off-by: Evgeny Voevodin <evgeny.voevodin@intel.com>
[vgupta: updated changelog and also added some comments]
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
During mmaping of frame-buffer pages to user-space
fb_protect() is called to set proper page settings.
In case of ARC we need to mark pages that are mmaped to
user as uncached because of 2 reasons:
* Huge amount of data if passing through data cache will
thrash cache a lot making cache almost useless for other
less traffic hungry processes.
* Data written by user in FB will be immediately available for
hardware (such as PGU etc) without requirements to flush data
cache regularly.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: linux-snps-arc@lists.infradead.org
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
There are only three patches this time, most other changes to
files in include/asm-generic tend to go through the tree of whoever
depends on the change.
Two patches are cleanups for stuff that is no longer needed,
the main change is to adapt the generic version of BUG_ON()
for CONFIG_BUG=n to make it behave consistently with BUG().
This avoids undefined behavior along with a number of warnings
about that undefined behavior in randconfig builds when
we keep going on after hitting a BUG_ON().
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=8tPL
-----END PGP SIGNATURE-----
Merge tag 'asm-generic-4.6' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic
Pull asm-generic updates from Arnd Bergmann:
"There are only three patches this time, most other changes to files in
include/asm-generic tend to go through the tree of whoever depends on
the change.
Two patches are cleanups for stuff that is no longer needed, the main
change is to adapt the generic version of BUG_ON() for CONFIG_BUG=n to
make it behave consistently with BUG().
This avoids undefined behavior along with a number of warnings about
that undefined behavior in randconfig builds when we keep going on
after hitting a BUG_ON()"
* tag 'asm-generic-4.6' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic:
asm-generic: remove old nonatomic-io wrapper files
asm-generic: default BUG_ON(x) to if(x)BUG()
asm-generic: page.h: Remove useless get_user_page and free_user_page
- Big Endian io accessors fix [Lada]
- Spellos fixes [Adam]
- Fix for DW GMAC breakage [Alexey]
- Making DMA API 64-bit ready
- Shutting up -Wmaybe-uninitialized noise for ARC
- Other minor fixes here and there, comments update
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=n0fk
-----END PGP SIGNATURE-----
Merge tag 'arc-4.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc
Pull ARC architecture updates from Vineet Gupta:
- Big Endian io accessors fix [Lada]
- Spellos fixes [Adam]
- Fix for DW GMAC breakage [Alexey]
- Making DMA API 64-bit ready
- Shutting up -Wmaybe-uninitialized noise for ARC
- Other minor fixes here and there, comments update
* tag 'arc-4.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc: (21 commits)
ARCv2: ioremap: Support dynamic peripheral address space
ARC: dma: reintroduce platform specific dma<->phys
ARC: dma: ioremap: use phys_addr_t consistenctly in code paths
ARC: dma: pass_phys() not sg_virt() to cache ops
ARC: dma: non-coherent pages need V-P mapping if in HIGHMEM
ARC: dma: Use struct page based page allocator helpers
ARC: build: Turn off -Wmaybe-uninitialized for ARC gcc 4.8
ARC: [plat-axs10x] add Ethernet PHY description in .dts
arc: use of_platform_default_populate() to populate default bus
ARC: thp: unbork !CONFIG_TRANSPARENT_HUGEPAGE build
arc: [plat-nsimosci*] use ezchip network driver
ARCv2: LLSC: software backoff is NOT needed starting HS2.1c
ARC: mm: Use virt_to_pfn() for addr >> PAGE_SHIFT pattern
ARC: [plat-nsim] document ranges
ARC: build: Better way to detect ISA compatible toolchain
ARCv2: Allow enabling PAE40 w/o HIGHMEM
ARC: [BE] readl()/writel() to work in Big Endian CPU configuration
ARC: [*defconfig] No need to specify CONFIG_CROSS_COMPILE
ARC: [BE] Select correct CROSS_COMPILE prefix
ARC: bitops: Remove non relevant comments
...
Pull networking updates from David Miller:
"Highlights:
1) Support more Realtek wireless chips, from Jes Sorenson.
2) New BPF types for per-cpu hash and arrap maps, from Alexei
Starovoitov.
3) Make several TCP sysctls per-namespace, from Nikolay Borisov.
4) Allow the use of SO_REUSEPORT in order to do per-thread processing
of incoming TCP/UDP connections. The muxing can be done using a
BPF program which hashes the incoming packet. From Craig Gallek.
5) Add a multiplexer for TCP streams, to provide a messaged based
interface. BPF programs can be used to determine the message
boundaries. From Tom Herbert.
6) Add 802.1AE MACSEC support, from Sabrina Dubroca.
7) Avoid factorial complexity when taking down an inetdev interface
with lots of configured addresses. We were doing things like
traversing the entire address less for each address removed, and
flushing the entire netfilter conntrack table for every address as
well.
8) Add and use SKB bulk free infrastructure, from Jesper Brouer.
9) Allow offloading u32 classifiers to hardware, and implement for
ixgbe, from John Fastabend.
10) Allow configuring IRQ coalescing parameters on a per-queue basis,
from Kan Liang.
11) Extend ethtool so that larger link mode masks can be supported.
From David Decotigny.
12) Introduce devlink, which can be used to configure port link types
(ethernet vs Infiniband, etc.), port splitting, and switch device
level attributes as a whole. From Jiri Pirko.
13) Hardware offload support for flower classifiers, from Amir Vadai.
14) Add "Local Checksum Offload". Basically, for a tunneled packet
the checksum of the outer header is 'constant' (because with the
checksum field filled into the inner protocol header, the payload
of the outer frame checksums to 'zero'), and we can take advantage
of that in various ways. From Edward Cree"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1548 commits)
bonding: fix bond_get_stats()
net: bcmgenet: fix dma api length mismatch
net/mlx4_core: Fix backward compatibility on VFs
phy: mdio-thunder: Fix some Kconfig typos
lan78xx: add ndo_get_stats64
lan78xx: handle statistics counter rollover
RDS: TCP: Remove unused constant
RDS: TCP: Add sysctl tunables for sndbuf/rcvbuf on rds-tcp socket
net: smc911x: convert pxa dma to dmaengine
team: remove duplicate set of flag IFF_MULTICAST
bonding: remove duplicate set of flag IFF_MULTICAST
net: fix a comment typo
ethernet: micrel: fix some error codes
ip_tunnels, bpf: define IP_TUNNEL_OPTS_MAX and use it
bpf, dst: add and use dst_tclassid helper
bpf: make skb->tc_classid also readable
net: mvneta: bm: clarify dependencies
cls_bpf: reset class and reuse major in da
ldmvsw: Checkpatch sunvnet.c and sunvnet_common.c
ldmvsw: Add ldmvsw.c driver code
...
The peripheral address space is architectural address window which is
uncached and typically used to wire up peripherals.
For ARC700 cores (ARCompact ISA based) this was fixed to 1GB region
0xC000_0000 - 0xFFFF_FFFF.
For ARCv2 based HS38 cores the start address is flexible and can be
0xC, 0xD, 0xE, 0xF 000_000 by programming AUX_NON_VOLATILE_LIMIT reg
(typically done in bootloader)
Further in cas of PAE, the physical address can extend beyond 4GB so
need to confine this check, otherwise all pages beyond 4GB will be
treated as uncached
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
With THP refcounting work, no need to mark PMDs splitting.
(ARC got missed under the sweeping arch change as THP support was likely
not present in orig baseline)
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
linux-next for 4.6-rc1 timeline reported ARC build failures !THP
| arch/arc/include/asm/tlbflush.h:29:0: warning: "flush_pmd_tlb_range" redefined [enabled by default]
| arch/arc/include/asm/tlbflush.h:29:0: warning: "flush_pmd_tlb_range" redefined [enabled by default]
| arch/arc/include/asm/tlbflush.h:29:0: warning: "flush_pmd_tlb_range" redefined [enabled by default]
Turns out that commit ("mm/thp/migration: switch from flush_tlb_range
to flush_pmd_tlb_range") triggered the issue while the problem was in
ARC code where THP specific helpers were not guarded with #ifdef.
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
This patch updates all instances of csum_tcpudp_magic and
csum_tcpudp_nofold to reflect the types that are usually used as the source
inputs. For example the protocol field is populated based on nexthdr which
is actually an unsigned 8 bit value. The length is usually populated based
on skb->len which is an unsigned integer.
This addresses an issue in which the IPv6 function csum_ipv6_magic was
generating a checksum using the full 32b of skb->len while
csum_tcpudp_magic was only using the lower 16 bits. As a result we could
run into issues when attempting to adjust the checksum as there was no
protocol agnostic way to update it.
With this change the value is still truncated as many architectures use
"(len + proto) << 8", however this truncation only occurs for values
greater than 16776960 in length and as such is unlikely to occur as we stop
the inner headers at ~64K in size.
I did have to make a few minor changes in the arm, mn10300, nios2, and
score versions of the function in order to support these changes as they
were either using things such as an OR to combine the protocol and length,
or were using ntohs to convert the length which would have truncated the
value.
I also updated a few spots in terms of whitespace and type differences for
the addresses. Most of this was just to make sure all of the definitions
were in sync going forward.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ARC architecture has 2 instruction sets: ARCompact/ARCv2.
While same gcc supports compiling for either (using appropriate toggles),
we can't use the same toolchain to build kernel because libgcc needs
to be unique and the toolchian (uClibc based) is not multilibed.
uClibc toolchain is convenient since it allows all userspace and
kernel to be built with a single install for an ISA.
This however means 2 gnu installs (with same triplet prefix) are needed
for building for 2 ISA and need to be in PATH.
As developers we keep switching the builds, but would occassionally fail
to update the PATH leading to usage of wrong tools. And this would only
show up at the end of kernel build when linking incompatible libgcc.
So the initial solution was to have gcc define a special preprocessor macro
DEFAULT_CPU_xxx which is unique for default toolchain configuration.
Claudiu proposed using grep for an existing preprocessor macro which is
again uniquely defined per ISA.
Cc: Michal Marek <mmarek@suse.cz>
Suggested-by: Claudiu Zissulescu <claziss@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
read{l,w}() write{l,w}() primitives should use le{16,32}_to_cpu() and
cpu_to_le{16,32}() respectively to ensure device registers are read
correctly in Big Endian CPU configuration.
Per Arnd Bergmann
| Most drivers using readl() or readl_relaxed() expect those to perform byte
| swaps on big-endian architectures, as the registers tend to be fixed endian
This was needed for getting UART to work correctly on a Big Endian ARC.
The ARC accessors originally were fine, and the bug got introduced
inadventently by commit b8a0330239 ("ARCv2: barriers")
Fixes: b8a0330239 ("ARCv2: barriers")
Link: http://lkml.kernel.org/r/201603100845.30602.arnd@arndb.de
Cc: Alexey Brodkin <abrodkin@synopsys.com>
Cc: stable@vger.kernel.org [4.2+]
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Lada Trimasova <ltrimas@synopsys.com>
[vgupta: beefed up changelog, added Fixes/stable tags]
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
commit 80f420842f removed the ARC bitops microoptimization but failed
to prune the comments to same effect
Fixes: 80f420842f ("ARC: Make ARC bitops "safer" (add anti-optimization)")
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Add PCI support to ARC and update drivers/pci Makefile enabling the ARC
arch to use the generic PCI setup functions.
[bhelgaas: fold in Joao's pci-dma-compat.h & pci-bridge.h build fix (I
should have caught this myself, sorry]
Signed-off-by: Joao Pinto <jpinto@synopsys.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Vineet Gupta <vgupta@synopsys.com>
They are not symmetric with each other, neither are used in real world
(can not be found by grep command in source code root directory), so
remove them.
Signed-off-by: Chen Gang <gang.chen.5i5j@gmail.com>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
There is no real ARC700 based SMP SoC so remove IPI definition.
EZChip's SMP ARC700 is going to use a different intc and IPI provider
anyways.
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
ARConnect/MCIP Inter-Core-Interrupt module can't send interrupt to
local core. So use core intc capability to trigger software
interrupt to self, using an unsued IRQ #21.
This showed up as csd deadlock with LTP trace_sched on a dual core
system. This test acts as scheduler fuzzer, triggering all sorts of
schedulting activity. Trouble starts with IPI to self, which doesn't get
delivered (effectively lost due to H/w capability), but the msg intended
to be sent remain enqueued in per-cpu @ipi_data.
All subsequent IPIs to this core from other cores get elided due to the
IPI coalescing optimization in ipi_send_msg_one() where a pending msg
implies an IPI already sent and assumes other core is yet to ack it.
After the elided IPI, other core simply goes into csd_lock_wait()
but never comes out as this core never sees the interrupt.
Fixes STAR 9001008624
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: <stable@vger.kernel.org> [4.2]
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
- ARCv2 uses a seperate BCR for {I,D}CCM base address:
ARCompact encoded both base/size in same BCR
- Size encoding in common BCR is different for ARCompact/ARCv2
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
- Corner case of returning to delay slot from interrupt
- Changing default interrupt prioiry level
- Kconfig'ize support for super pages
- Other minor fixes
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=FNDd
-----END PGP SIGNATURE-----
Merge tag 'arc-4.5-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc
Pull ARC fixes from Vineet Gupta:
"I've been sitting on some of these fixes for a while.
- Corner case of returning to delay slot from interrupt
- Changing default interrupt prioiry level
- Kconfig'ize support for super pages
- Other minor fixes"
* tag 'arc-4.5-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc:
ARC: mm: Introduce explicit super page size support
ARCv2: intc: Allow interruption by lowest priority interrupt
ARCv2: Check for LL-SC livelock only if LLSC is enabled
ARC: shrink cpuinfo by not saving full timer BCR
ARCv2: clocksource: Rename GRTC -> GFRC ...
ARCv2: STAR 9000950267: Handle return from intr to Delay Slot #2
MMUv4 supports 2 concurrent page sizes: Normal and Super [4K to 16M]
So far Linux supported a single super page size for a given Normal page,
depending on the software page walking address split.
e.g. we had 11:8:13 address split for 8K page, which meant super page
was 2 ^(8+13) = 2M (given that THP size has to be PMD_SHIFT)
Now we turn this around, by allowing multiple Super Pages in Kconfig
(currently 2M and 16M only) and forcing page walker address split to
PGDIR_SHIFT and PAGE_SHIFT
For configs without Super page, things are same as before and
PGDIR_SHIFT can be hacked to get non default address split
The motivation for this change is a customer who needs 16M super page
and a 8K Normal page combo.
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
ARC HS Cores support configurable multiple interrupt priorities of upto
16 levels.
There is processor "interrupt preemption threshhold" in STATUS32.E[4:1]
And several places need to set this up:
1. seed value as kernel is booting
2. seed value for user space programs
3. Arg to SLEEP instruction in idle task (what interrupt prio can wake)
4. Per-IRQ line prioirty (i.e. what is the priority of interrupt
raised by a peripheral or timer or perf counter...
Currently above sites use the highest priority 0. This can be potential
problem when multiple priorities are supported. e.g. user space could
only be interrupted by P0 interrupt, not others...
So turn this over and instead make default interruption level to be
the lowest priority possible 15. This should be fine even if there are
fewer priority levels configured (say two: P0 HIGH, P1 LOW)
This feature also effectively disables FIRQ feature if present in
hardware config. With old code, a P0 interrupt would be FIRQ, needing
special handling (ISR or Register Banks) which is NOT supported yet.
Now it not be P0 (P15 or whatever is lowest prio) so FIRQ is not
triggered.
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Move the generic implementation to <linux/dma-mapping.h> now that all
architectures support it and remove the HAVE_DMA_ATTR Kconfig symbol now
that everyone supports them.
[valentinrothberg@gmail.com: remove leftovers in Kconfig]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Aurelien Jacquiot <a-jacquiot@ti.com>
Cc: Chris Metcalf <cmetcalf@ezchip.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Haavard Skinnemoen <hskinnemoen@gmail.com>
Cc: Hans-Christian Egtvedt <egtvedt@samfundet.no>
Cc: Helge Deller <deller@gmx.de>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Jesper Nilsson <jesper.nilsson@axis.com>
Cc: Koichi Yasutake <yasutake.koichi@jp.panasonic.com>
Cc: Ley Foon Tan <lftan@altera.com>
Cc: Mark Salter <msalter@redhat.com>
Cc: Mikael Starvik <starvik@axis.com>
Cc: Steven Miao <realmz6@gmail.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: Joerg Roedel <jroedel@suse.de>
Cc: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Valentin Rothberg <valentinrothberg@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
ARC700 cores with MMU v2 don't have IC_PTAG AUX register and so we only
define ARC_REG_IC_PTAG for MMU versions >= 3.
But current implementation of cache_line_loop_vX() routines assumes
availability of all of them (v2, v3 and v4) simultaneously.
And given undefined ARC_REG_IC_PTAG if CONFIG_MMU_VER=2 we're seeing
compilation problem:
---------------------------------->8-------------------------------
CC arch/arc/mm/cache.o
arch/arc/mm/cache.c: In function '__cache_line_loop_v3':
arch/arc/mm/cache.c:270:13: error: 'ARC_REG_IC_PTAG' undeclared (first use in this function)
aux_tag = ARC_REG_IC_PTAG;
^
arch/arc/mm/cache.c:270:13: note: each undeclared identifier is reported only once for each function it appears in
scripts/Makefile.build:258: recipe for target 'arch/arc/mm/cache.o' failed
---------------------------------->8-------------------------------
The simples fix is to have ARC_REG_IC_PTAG defined regardless MMU
version being used.
We don't use it in cache_line_loop_v2() anyways so who cares.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
This will better reflect its description i.e. "any needed setup..."
and not just do an "IPI request".
Signed-off-by: Noam Camus <noamc@ezchip.com>
Acked-by: Vineet Gupta <vgupta@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
The fix which removed linear searching of dwarf (because binary lookup
data always exists) missed out on the fact that modules don't get the
binary lookup tables info. This caused unwinding out of modules to stop
working.
So add binary lookup header setup (equivalent of eh_frame_hdr setup) to
modules as well.
While at it, confine the header setup to within unwinder code,
reducing one API exposed out of unwinder code.
Fixes: 2e22502c08 ARC: dw2 unwind: Remove falllback linear search thru FDE entries
Cc: <stable@vger.kernel.org>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Although kernel doesn't support the multiple IRQ priority levels provided
by HS38x core intc yet, ensure that the default prio value is used
anyways by relevant code.
SLEEP insn needs to be provided the IRQ priority level which can
interrupt it. This needs to be the default level which maynot
necessarily be 0 as assumed by current code.
This change allows a kernel with ARCV2_IRQ_DEF_PRIO = 1 to boot fine.
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
- A bunch of brown paper bag bugs (MAINTAINERS list email, SMP build failure)
- cpu_relax() now compiler barrier for UP as well
- Handling of userspace Bus Errors for ARCompact builds
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=isVd
-----END PGP SIGNATURE-----
Merge tag 'arc-4.4-rc1-part2' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc
Pull ARC fixes from Vineet Gupta:
"Found a couple of brown paper bag bugs with the prev pull request
(including a SMP build breakage report from Guenter). Since these are
urgent I also decided to send over a bunch of other pending fixes
which could have otherwise waited an rc or two.
Summary:
- A bunch of brown paper bag bugs (MAINTAINERS list email, SMP build
failure)
- cpu_relax() now compiler barrier for UP as well
- handling of userspace Bus Errors for ARCompact builds"
* tag 'arc-4.4-rc1-part2' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc:
ARC: Fix silly typo in MAINTAINERS file
ARC: cpu_relax() to be compiler barrier even for UP
ARC: use ASL assembler mnemonic
ARC: [arcompact] Handle bus error from userspace as Interrupt not exception
ARC: remove extraneous header include
ARCv2: lib: memcpy: use local symbols
cpu_relax() on ARC has been barrier only for SMP (and no-op for UP). Per
recent discussions, it is safer to make it a compiler barrier
unconditionally.
Link: http://lkml.kernel.org/r/53A7D3AA.9020100@synopsys.com
Acked-by: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Pull locking changes from Ingo Molnar:
"The main changes in this cycle were:
- More gradual enhancements to atomic ops: new atomic*_read_ctrl()
ops, synchronize atomic_{read,set}() ordering requirements between
architectures, add atomic_long_t bitops. (Peter Zijlstra)
- Add _{relaxed|acquire|release}() variants for inc/dec atomics and
use them in various locking primitives: mutex, rtmutex, mcs, rwsem.
This enables weakly ordered architectures (such as arm64) to make
use of more locking related optimizations. (Davidlohr Bueso)
- Implement atomic[64]_{inc,dec}_relaxed() on ARM. (Will Deacon)
- Futex kernel data cache footprint micro-optimization. (Rasmus
Villemoes)
- pvqspinlock runtime overhead micro-optimization. (Waiman Long)
- misc smaller fixlets"
* 'locking-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
ARM, locking/atomics: Implement _relaxed variants of atomic[64]_{inc,dec}
locking/rwsem: Use acquire/release semantics
locking/mcs: Use acquire/release semantics
locking/rtmutex: Use acquire/release semantics
locking/mutex: Use acquire/release semantics
locking/asm-generic: Add _{relaxed|acquire|release}() variants for inc/dec atomics
atomic: Implement atomic_read_ctrl()
atomic, arch: Audit atomic_{read,set}()
atomic: Add atomic_long_t bitops
futex: Force hot variables into a single cache line
locking/pvqspinlock: Kick the PV CPU unconditionally when _Q_SLOW_VAL
locking/osq: Relax atomic semantics
locking/qrwlock: Rename ->lock to ->wait_lock
locking/Documentation/lockstat: Fix typo - lokcing -> locking
locking/atomics, cmpxchg: Privatize the inclusion of asm/cmpxchg.h
This is the first working implementation of 40-bit physical address
extension on ARCv2.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
That way a single flip of phys_addr_t to 64 bit ensures all places
dealing with physical addresses get correct data
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Implement kmap* API for ARC.
This enables
- permanent kernel maps (pkmaps): :kmap() API
- fixmap : kmap_atomic()
We use a very simple/uniform approach for both (unlike some of the other
arches). So fixmap doesn't use the customary compile time address stuff.
The important semantic is sleep'ability (pkmap) vs. not (fixmap) which
the API guarantees.
Note that this patch only enables highmem for subsequent PAE40 support
as there is no real highmem for ARC in pure 32-bit paradigm as explained
below.
ARC has 2:2 address split of the 32-bit address space with lower half
being translated (virtual) while upper half unstranslated
(0x8000_0000 to 0xFFFF_FFFF). kernel itself is linked at base of
unstranslated space (i.e. 0x8000_0000 onwards), which is mapped to say
DDR 0x0 by external Bus Glue logic (outside the core). So kernel can
potentially access 1.75G worth of memory directly w/o need for highmem.
(the top 256M is taken by uncached peripheral space from 0xF000_0000 to
0xFFFF_FFFF)
In PAE40, hardware can address memory beyond 4G (0x1_0000_0000) while
the logical/virtual addresses remain 32-bits. Thus highmem is required
for kernel proper to be able to access these pages for it's own purposes
(user space is agnostic to this anyways).
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Before we plug in highmem support, some of code needs to be ready for it
- copy_user_highpage() needs to be using the kmap_atomic API
- mk_pte() can't assume page_address()
- do_page_fault() can't assume VMALLOC_END is end of kernel vaddr space
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
MCIP now registers it's own per cpu setup routine (for IPI IRQ request)
using smp_ops.init_irq_cpu().
So no need for platforms to do that. This now completely decouples
platforms from MCIP.
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Note this is not part of platform owned static machine_desc,
but more of device owned plat_smp_ops (rather misnamed) which a IPI
provider or some such typically defines.
This will help us seperate out the IPI registration from platform
specific init_cpu_smp() into device specific init_irq_cpu()
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
MCIP now registers it's own probe callback with smp_ops.init_early_smp()
which is called by ARC common code, so no need for platforms to do that.
This decouples the platforms and MCIP and helps confine MCIP details
to it's own file.
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
This adds a platform agnostic early SMP init hook which is called on
Master core before calling setup_processor()
setup_arch()
smp_init_cpus()
smp_ops.init_early_smp()
...
setup_processor()
How this helps:
- Used for one time init of certain SMP centric IP blocks, before
calling setup_processor() which probes various bits of core,
possibly including this block
- Currently platforms need to call this IP block init from their
init routines, which doesn't make sense as this is specific to ARC
core and not platform and otherwise requires copy/paste in all
(and hence a possible point of failure)
e.g. MCIP init is called from 2 platforms currently (axs10x and sim)
which will go away once we have this.
This change only adds the hooks but they are empty for now. Next commit
will populate them and remove the explicit init calls from platforms.
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
These are not in use for ARC platforms. Moreover DT mechanims exist to
probe them w/o explicit platform calls.
- clocksource drivers can use CLOCKSOURCE_OF_DECLARE()
- intc IRQCHIP_DECLARE() calls + cascading inside DT allows external
intc to be probed automatically
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
The reason this was not done so far was lack of genuine IPI_IRQ for
ARC700, as we don't have a SMP version of core yet (which might change
soon thx to EZChip). Nevertheles to increase the build coverage, we
need to allow CONFIG_SMP for ARC700 and still be able to run it on a
UP platform (nsim or AXS101) with a UP Device Tree (SMP-on-UP)
The build itself requires some define for IPI_IRQ and even a dummy
value is fine since that code won't run anyways.
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
This frees up some bits to hold more high level info such as PAE being
present, w/o increasing the size of already bloated cpuinfo struct
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
The requirement is to
- Reenable Exceptions (AE cleared)
- Reenable Interrupts (E1/E2 set)
We need to do wiggle these bits into ERSTATUS and call RTIE.
Prev version used the pre-exception STATUS32 as starting point for what
goes into ERSTATUS. This required explicit fixups of U/DE/L bits.
Instead, use the current (in-exception) STATUS32 as starting point.
Being in exception handler U/DE/L can be safely assumed to be correct.
Only AE/E1/E2 need to be fixed.
So the new implementation is slightly better
-Avoids read form memory
-Is 4 bytes smaller for the typical 1 level of intr configuration
-Depicts the semantics more clearly
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Historically this was done by ARC IDE driver, which is long gone.
IRQ core is pretty robust now and already checks if IRQs are enabled
in hard ISRs. Thus no point in checking this in arch code, for every
call of irq enabled.
Further if some driver does do that - let it bring down the system so we
notice/fix this sooner than covering up for sucker
This makes local_irq_enable() - for L1 only case atleast simple enough
so we can inline it.
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Implement the TLB flush routine to evict a sepcific Super TLB entry,
vs. moving to a new ASID on every such flush.
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
MMUv4 in HS38x cores supports Super Pages which are basis for Linux THP
support.
Normal and Super pages can co-exist (ofcourse not overlap) in TLB with a
new bit "SZ" in TLB page desciptor to distinguish between them.
Super Page size is configurable in hardware (4K to 16M), but fixed once
RTL builds.
The exact THP size a Linx configuration will support is a function of:
- MMU page size (typical 8K, RTL fixed)
- software page walker address split between PGD:PTE:PFN (typical
11:8:13, but can be changed with 1 line)
So for above default, THP size supported is 8K * 256 = 2M
Default Page Walker is 2 levels, PGD:PTE:PFN, which in THP regime
reduces to 1 level (as PTE is folded into PGD and canonically referred
to as PMD).
Thus thp PMD accessors are implemented in terms of PTE (just like sparc)
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
ARC is the only arch with unsigned long type (vs. struct page *).
Historically this was done to avoid the page_address() calls in various
arch hooks which need to get the virtual/logical address of the table.
Some arches alternately define it as pte_t *, and is as efficient as
unsigned long (generated code doesn't change)
Suggested-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Pull strscpy string copy function implementation from Chris Metcalf.
Chris sent this during the merge window, but I waffled back and forth on
the pull request, which is why it's going in only now.
The new "strscpy()" function is definitely easier to use and more secure
than either strncpy() or strlcpy(), both of which are horrible nasty
interfaces that have serious and irredeemable problems.
strncpy() has a useless return value, and doesn't NUL-terminate an
overlong result. To make matters worse, it pads a short result with
zeroes, which is a performance disaster if you have big buffers.
strlcpy(), by contrast, is a mis-designed "fix" for strlcpy(), lacking
the insane NUL padding, but having a differently broken return value
which returns the original length of the source string. Which means
that it will read characters past the count from the source buffer, and
you have to trust the source to be properly terminated. It also makes
error handling fragile, since the test for overflow is unnecessarily
subtle.
strscpy() avoids both these problems, guaranteeing the NUL termination
(but not excessive padding) if the destination size wasn't zero, and
making the overflow condition very obvious by returning -E2BIG. It also
doesn't read past the size of the source, and can thus be used for
untrusted source data too.
So why did I waffle about this for so long?
Every time we introduce a new-and-improved interface, people start doing
these interminable series of trivial conversion patches.
And every time that happens, somebody does some silly mistake, and the
conversion patch to the improved interface actually makes things worse.
Because the patch is mindnumbing and trivial, nobody has the attention
span to look at it carefully, and it's usually done over large swatches
of source code which means that not every conversion gets tested.
So I'm pulling the strscpy() support because it *is* a better interface.
But I will refuse to pull mindless conversion patches. Use this in
places where it makes sense, but don't do trivial patches to fix things
that aren't actually known to be broken.
* 'strscpy' of git://git.kernel.org/pub/scm/linux/kernel/git/cmetcalf/linux-tile:
tile: use global strscpy() rather than private copy
string: provide strscpy()
Make asm/word-at-a-time.h available on all architectures
This patch makes sure that atomic_{read,set}() are at least
{READ,WRITE}_ONCE().
We already had the 'requirement' that atomic_read() should use
ACCESS_ONCE(), and most archs had this, but a few were lacking.
All are now converted to use READ_ONCE().
And, by a symmetry and general paranoia argument, upgrade atomic_set()
to use WRITE_ONCE().
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Dmitry Vyukov <dvyukov@google.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: james.hogan@imgtec.com
Cc: linux-kernel@vger.kernel.org
Cc: oleg@redhat.com
Cc: will.deacon@arm.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Pull locking and atomic updates from Ingo Molnar:
"Main changes in this cycle are:
- Extend atomic primitives with coherent logic op primitives
(atomic_{or,and,xor}()) and deprecate the old partial APIs
(atomic_{set,clear}_mask())
The old ops were incoherent with incompatible signatures across
architectures and with incomplete support. Now every architecture
supports the primitives consistently (by Peter Zijlstra)
- Generic support for 'relaxed atomics':
- _acquire/release/relaxed() flavours of xchg(), cmpxchg() and {add,sub}_return()
- atomic_read_acquire()
- atomic_set_release()
This came out of porting qwrlock code to arm64 (by Will Deacon)
- Clean up the fragile static_key APIs that were causing repeat bugs,
by introducing a new one:
DEFINE_STATIC_KEY_TRUE(name);
DEFINE_STATIC_KEY_FALSE(name);
which define a key of different types with an initial true/false
value.
Then allow:
static_branch_likely()
static_branch_unlikely()
to take a key of either type and emit the right instruction for the
case. To be able to know the 'type' of the static key we encode it
in the jump entry (by Peter Zijlstra)
- Static key self-tests (by Jason Baron)
- qrwlock optimizations (by Waiman Long)
- small futex enhancements (by Davidlohr Bueso)
- ... and misc other changes"
* 'locking-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (63 commits)
jump_label/x86: Work around asm build bug on older/backported GCCs
locking, ARM, atomics: Define our SMP atomics in terms of _relaxed() operations
locking, include/llist: Use linux/atomic.h instead of asm/cmpxchg.h
locking/qrwlock: Make use of _{acquire|release|relaxed}() atomics
locking/qrwlock: Implement queue_write_unlock() using smp_store_release()
locking/lockref: Remove homebrew cmpxchg64_relaxed() macro definition
locking, asm-generic: Add _{relaxed|acquire|release}() variants for 'atomic_long_t'
locking, asm-generic: Rework atomic-long.h to avoid bulk code duplication
locking/atomics: Add _{acquire|release|relaxed}() variants of some atomic operations
locking, compiler.h: Cast away attributes in the WRITE_ONCE() magic
locking/static_keys: Make verify_keys() static
jump label, locking/static_keys: Update docs
locking/static_keys: Provide a selftest
jump_label: Provide a self-test
s390/uaccess, locking/static_keys: employ static_branch_likely()
x86, tsc, locking/static_keys: Employ static_branch_likely()
locking/static_keys: Add selftest
locking/static_keys: Add a new static_key interface
locking/static_keys: Rework update logic
locking/static_keys: Add static_key_{en,dis}able() helpers
...
With all features in place, the ARC HS pct block can now be effectively
allowed to be probed/used
Acked-by: Peter Zijlstra <peterz@infradead.org>
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
In times of ARC 700 performance counters didn't have support of
interrupt an so for ARC we only had support of non-sampling events.
Put simply only "perf stat" was functional.
Now with ARC HS we have support of interrupts in performance counters
which this change introduces support of.
ARC performance counters act in the following way in regard of
interrupts generation.
[1] A counter counts starting from value set in PCT_COUNT register pair
[2] Once counter reaches value set in PCT_INT_CNT interrupt is raised
Basic setup look like this:
[1] PCT_COUNT = 0;
[2] PCT_INT_CNT = __limit_value__;
[3] Enable interrupts for that counter and let it run
[4] Let counter reach its limit
[5] Handle interrupt when it happens
Note that PCT HW block is build in CPU core and so ints interrupt
line (which is basically OR of all counters IRQs) is wired directly to
top-level IRQC. That means do de-assert PCT interrupt it's required to
reset IRQs from all counters that have reached their limit values.
Acked-by: Peter Zijlstra <peterz@infradead.org>
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
The number of counters in PCT can never be more than 32 (while
countable conditions could be 100+) for both ARCompact and ARCv2
And while at it update copyright dates.
Acked-by: Peter Zijlstra <peterz@infradead.org>
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
When kernel's binary becomes large enough (32M and more) errors
may occur during the final linkage stage. It happens because
the build system uses short relocations for ARC by default.
This problem may be easily resolved by passing -mlong-calls
option to GCC to use long absolute jumps (j) instead of short
relative branchs (b).
But there are fragments of pure assembler code exist which use
branchs in inappropriate places and cause a linkage error because
of relocations overflow.
First of these fragments is .fixup insertion in futex.h and
unaligned.c. It inserts a code in the separate section (.fixup)
with branch instruction. It leads to the linkage error when
kernel becomes large.
Second of these fragments is calling scheduler's functions
(common kernel code) from entry.S of ARC's code. When kernel's
binary becomes large it may lead to the linkage error because
scheduler may occur far enough from ARC's code in the final
binary.
Signed-off-by: Yuriy Kolerov <yuriy.kolerov@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
W/o hardware assisted atomic r-m-w the best we can do is to disable
preemption.
Cc: David Hildenbrand <dahi@linux.vnet.ibm.com>
Cc: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Michel Lespinasse <walken@google.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Callers of cmpxchg_futex_value_locked() in futex code expect bimodal
return value:
!0 (essentially -EFAULT as failure)
0 (success)
Before this patch, the success return value was old value of futex,
which could very well be non zero, causing caller to possibly take the
failure path erroneously.
Fix that by returning 0 for success
(This fix was done back in 2011 for all upstream arches, which ARC
obviously missed)
Cc: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Michel Lespinasse <walken@google.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
The atomic ops on futex need to provide the full barrier just like
regular atomics in kernel.
Also remove pagefault_enable/disable in futex_atomic_cmpxchg_inatomic()
as core code already does that
Cc: David Hildenbrand <dahi@linux.vnet.ibm.com>
Cc: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Michel Lespinasse <walken@google.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
In case of ARCv2 CPU there're could be following configurations
that affect cache handling for data exchanged with peripherals
via DMA:
[1] Only L1 cache exists
[2] Both L1 and L2 exist, but no IO coherency unit
[3] L1, L2 caches and IO coherency unit exist
Current implementation takes care of [1] and [2].
Moreover support of [2] is implemented with run-time check
for SLC existence which is not super optimal.
This patch introduces support of [3] and rework of DMA ops
usage. Instead of doing run-time check every time a particular
DMA op is executed we'll have 3 different implementations of
DMA ops and select appropriate one during init.
As for IOC support for it we need:
[a] Implement empty DMA ops because IOC takes care of cache
coherency with DMAed data
[b] Route dma_alloc_coherent() via dma_alloc_noncoherent()
This is required to make IOC work in first place and also
serves as optimization as LD/ST to coherent buffers can be
srviced from caches w/o going all the way to memory
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
[vgupta:
-Added some comments about IOC gains
-Marked dma ops as static,
-Massaged changelog a bit]
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
The increment of delay counter was 2 instructions:
Arithmatic Shfit Left (ASL) + set to 1 on overflow
This can be done in 1 using ROtate Left (ROL)
Suggested-by: Nigel Topham <ntopham@synopsys.com>
Cc: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
KGDB fails to build after f51e2f1911 ("ARC: make sure instruction_pointer()
returns unsigned value")
The hack to force one specific reg to unsigned backfired. There's no
reason to keep the regs signed after all.
| CC arch/arc/kernel/kgdb.o
|../arch/arc/kernel/kgdb.c: In function 'kgdb_trap':
| ../arch/arc/kernel/kgdb.c:180:29: error: lvalue required as left operand of assignment
| instruction_pointer(regs) -= BREAK_INSTR_SIZE;
Reported-by: Yuriy Kolerov <yuriy.kolerov@synopsys.com>
Fixes: f51e2f1911 ("ARC: make sure instruction_pointer() returns unsigned value")
Cc: Alexey Brodkin <abrodkin@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
The previous commit for delayed retry of SCOND needs some fine tuning
for spin locks.
The backoff from delayed retry in conjunction with spin looping of lock
itself can potentially cause the delay counter to reach high values.
So to provide fairness to any lock operation, after a lock "seems"
available (i.e. just before first SCOND try0, reset the delay counter
back to starting value of 1
Essentially reset delay to 1 for a new spin-wait-loop-acquire cycle.
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
This is to workaround the llock/scond livelock
HS38x4 could get into a LLOCK/SCOND livelock in case of multiple overlapping
coherency transactions in the SCU. The exclusive line state keeps rotating
among contenting cores leading to a never ending cycle. So break the cycle
by deferring the retry of failed exclusive access (SCOND). The actual delay
needed is function of number of contending cores as well as the unrelated
coherency traffic from other cores. To keep the code simple, start off with
small delay of 1 which would suffice most cases and in case of contention
double the delay. Eventually the delay is sufficient such that the coherency
pipeline is drained, thus a subsequent exclusive access would succeed.
Link: http://lkml.kernel.org/r/1438612568-28265-1-git-send-email-vgupta@synopsys.com
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
With LLOCK/SCOND, the rwlock counter can be atomically updated w/o need
for a guarding spin lock.
This in turn elides the EXchange instruction based spinning which causes
the cacheline transition to exclusive state and concurrent spinning
across cores would cause the line to keep bouncing around.
LLOCK/SCOND based implementation is superior as spinning on LLOCK keeps
the cacheline in shared state.
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Current spin_lock uses EXchange instruction to implement the atomic test
and set of lock location (reads orig value and ST 1). This however forces
the cacheline into exclusive state (because of the ST) and concurrent
loops in multiple cores will bounce the line around between cores.
Instead, use LLOCK/SCOND to implement the atomic test and set which is
better as line is in shared state while lock is spinning on LLOCK
The real motivation of this change however is to make way for future
changes in atomics to implement delayed retry (with backoff).
Initial experiment with delayed retry in atomics combined with orig
EX based spinlock was a total disaster (broke even LMBench) as
struct sock has a cache line sharing an atomic_t and spinlock. The
tight spinning on lock, caused the atomic retry to keep backing off
such that it would never finish.
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
This reduces the diff in forth-coming patches and also helps understand
better the incremental changes to inline asm.
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Extended testing of quad core configuration revealed that this fix was
insufficient. Specifically LTP open posix shm_op/23-1 would cause the
hardware livelock in llock/scond loop in update_cpu_load_active()
So remove this and make way for a proper workaround
This reverts commit a5c8b52abe.
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
With HS 2.1 release, the peripheral space register no longer contains
the uncached space specifics, causing the kernel to panic early on.
So read the newer NON VOLATILE AUX register to get that info.
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Move the now generic definitions of atomic_{set,clear}_mask() into
linux/atomic.h to avoid endless and pointless repetition.
Also, provide an atomic_andnot() wrapper for those few archs that can
implement that.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Implement atomic logic ops -- atomic_{or,xor,and}.
These will replace the atomic_{set,clear}_mask functions that are
available on some archs.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Implement atomic logic ops -- atomic_{or,xor,and}.
These will replace the atomic_{set,clear}_mask functions that are
available on some archs.
Acked-by: Vineet Gupta <vgupta@synopsys.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Commit 2ae416b142 ("mm: new mm hook framework") introduced an empty
header file (mm-arch-hooks.h) for every architecture, even those which
doesn't need to define mm hooks.
As suggested by Geert Uytterhoeven, this could be cleaned through the use
of a generic header file included via each per architecture
asm/include/Kbuild file.
The PowerPC architecture is not impacted here since this architecture has
to defined the arch_remap MM hook.
Signed-off-by: Laurent Dufour <ldufour@linux.vnet.ibm.com>
Suggested-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Vineet Gupta <vgupta@synopsys.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Currently instruction_pointer() returns pt_regs->ret and so return value
is of type "long", which implicitly stands for "signed long".
While that's perfectly fine when dealing with 32-bit values if return
value of instruction_pointer() gets assigned to 64-bit variable sign
extension may happen.
And at least in one real use-case it happens already.
In perf_prepare_sample() return value of perf_instruction_pointer()
(which is an alias to instruction_pointer() in case of ARC) is assigned
to (struct perf_sample_data)->ip (which type is "u64").
And what we see if instuction pointer points to user-space application
that in case of ARC lays below 0x8000_0000 "ip" gets set properly with
leading 32 zeros. But if instruction pointer points to kernel address
space that starts from 0x8000_0000 then "ip" is set with 32 leadig
"f"-s. I.e. id instruction_pointer() returns 0x8100_0000, "ip" will be
assigned with 0xffff_ffff__8100_0000. Which is obviously wrong.
In particular that issuse broke output of perf, because perf was unable
to associate addresses like 0xffff_ffff__8100_0000 with anything from
/proc/kallsyms.
That's what we used to see:
----------->8----------
6.27% ls [unknown] [k] 0xffffffff8046c5cc
2.96% ls libuClibc-0.9.34-git.so [.] memcpy
2.25% ls libuClibc-0.9.34-git.so [.] memset
1.66% ls [unknown] [k] 0xffffffff80666536
1.54% ls libuClibc-0.9.34-git.so [.] 0x000224d6
1.18% ls libuClibc-0.9.34-git.so [.] 0x00022472
----------->8----------
With that change perf output looks much better now:
----------->8----------
8.21% ls [kernel.kallsyms] [k] memset
3.52% ls libuClibc-0.9.34-git.so [.] memcpy
2.11% ls libuClibc-0.9.34-git.so [.] malloc
1.88% ls libuClibc-0.9.34-git.so [.] memset
1.64% ls [kernel.kallsyms] [k] _raw_spin_unlock_irqrestore
1.41% ls [kernel.kallsyms] [k] __d_lookup_rcu
----------->8----------
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: arc-linux-dev@synopsys.com
Cc: stable@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
ARCompact/ARCv2 ISA provide that any instructions which deals with
bitpos/count operand ASL, LSL, BSET, BCLR, BMSK .... will only consider
lower 5 bits. i.e. auto-clamp the pos to 0-31.
ARC Linux bitops exploited this fact by NOT explicitly masking out upper
bits for @nr operand in general, saving a bunch of AND/BMSK instructions
in generated code around bitops.
While this micro-optimization has worked well over years it is NOT safe
as shifting a number with a value, greater than native size is
"undefined" per "C" spec.
So as it turns outm EZChip ran into this eventually, in their massive
muti-core SMP build with 64 cpus. There was a test_bit() inside a loop
from 63 to 0 and gcc was weirdly optimizing away the first iteration
(so it was really adhering to standard by implementing undefined behaviour
vs. removing all the iterations which were phony i.e. (1 << [63..32])
| for i = 63 to 0
| X = ( 1 << i )
| if X == 0
| continue
So fix the code to do the explicit masking at the expense of generating
additional instructions. Fortunately, this can be mitigated to a large
extent as gcc has SHIFT_COUNT_TRUNCATED which allows combiner to fold
masking into shift operation itself. It is currently not enabled in ARC
gcc backend, but could be done after a bit of testing.
Fixes STAR 9000866918 ("unsafe "undefined behavior" code in kernel")
Reported-by: Noam Camus <noamc@ezchip.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Added the x86 implementation of word-at-a-time to the
generic version, which previously only supported big-endian.
Omitted the x86-specific load_unaligned_zeropad(), which in
any case is also not present for the existing BE-only
implementation of a word-at-a-time, and is only used under
CONFIG_DCACHE_WORD_ACCESS.
Added as a "generic-y" to the Kbuilds of all architectures
that didn't previously have it.
Signed-off-by: Chris Metcalf <cmetcalf@ezchip.com>
Merge third patchbomb from Andrew Morton:
- the rest of MM
- scripts/gdb updates
- ipc/ updates
- lib/ updates
- MAINTAINERS updates
- various other misc things
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (67 commits)
genalloc: rename of_get_named_gen_pool() to of_gen_pool_get()
genalloc: rename dev_get_gen_pool() to gen_pool_get()
x86: opt into HAVE_COPY_THREAD_TLS, for both 32-bit and 64-bit
MAINTAINERS: add zpool
MAINTAINERS: BCACHE: Kent Overstreet has changed email address
MAINTAINERS: move Jens Osterkamp to CREDITS
MAINTAINERS: remove unused nbd.h pattern
MAINTAINERS: update brcm gpio filename pattern
MAINTAINERS: update brcm dts pattern
MAINTAINERS: update sound soc intel patterns
MAINTAINERS: remove website for paride
MAINTAINERS: update Emulex ocrdma email addresses
bcache: use kvfree() in various places
libcxgbi: use kvfree() in cxgbi_free_big_mem()
target: use kvfree() in session alloc and free
IB/ehca: use kvfree() in ipz_queue_{cd}tor()
drm/nouveau/gem: use kvfree() in u_free()
drm: use kvfree() in drm_free_large()
cxgb4: use kvfree() in t4_free_mem()
cxgb3: use kvfree() in cxgb_free_mem()
...
ARCv2 is the next generation ISA from Synopsys and basis for the
HS3{4,6,8} families of processors which retain the traditional ARC mantra of
low power and configurability and are now more performant and feature rich.
HS38x is a 10 stage pipeline core which supports MMU (with huge pages) and
SMP (upto 4 cores) among other features.
+ www.synopsys.com/dw/ipdir.php?ds=arc-hs38-processor
+ http://news.synopsys.com/2014-10-14-New-DesignWare-ARC-HS38-Processor-Doubles-Performance-for-Embedded-Linux-Applications
+ http://www.embedded.com/electronics-news/4435975/Synopsys-ARC-HS38-core-gives-2X-boost-to-Linux-based-apps
- Support for ARC SDP (Software Development platform): Main Board + CPU Cards
= AXS101: CPU Card with ARC700 in silicon @ 700 MHz
= AXS103: CPU Card with HS38x in FPGA
- Refactoring of ARCompact port to accomodate new ARCv2 ISA
- Miscll updates/cleanups
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJVk0g8AAoJEGnX8d3iisJecqsQAI6gvBC4GSNYDrmgGJJK1uLQ
uf6ZXQRLBtyxwa6VMvaNFe91i5XV5WvEXDuNBQX4FdYbp7Fs+Jz5VK79xFtbVEdU
H6mgKcs9HBwQvrHBxl54XxxXfX7kD1kxrlV7cL4b7bXTEX0XyH5ROUj600/YP+B4
8t+XdYcfgFK0HpeFGXVP+Xmv/e+hBbzCpOjOd2ZFqEwymvSpZDc4KZ2yDvV2+Ybn
JNZ421urQOrxR27njvvPvtpeN7uuJKfRYq7IuIR8+Ad72S19EDdw+DZHp2XoUMXA
wgydWrrOaX2Dr2CmXHGA1C4nWEG7+Yo9I1WitjJct0tkOQyDR2OIDGmvKGBd1uoS
QsihtoKBRvns+2gpXBEOmOHmF6ggpHNN0ppIwCp+AK5kX3fmxBtyUekyYmVpg8oQ
xgFIuJgmiAvW7QB7xIO6SFFt18De2ifDRrKWJwVauvfW/PvUIwuUBEcbh0OHAn54
ebUUWu2ZdVNe0XCsZOAQGwYHZRWBk8Bn3bhFpNnOliRiF77e9GsKeGYeIswYFy7I
42Gp35ftEj1pLLFZ1vIsAo72N6ErmHwPOcJkaBYaTbPGPcTEO2aR6b8WOcCjsPxK
DUeUV3H2HV+6V4jw/96lnsaRqsaj4TsJxEAFRR3wT1DLoRudCIDubaXTdvvDie77
RgKn4ZdxgmXD97+deBqc
=KwNo
-----END PGP SIGNATURE-----
Merge tag 'arc-4.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc
Pull ARC architecture updates from Vineet Gupta:
- support for HS38 cores based on ARCv2 ISA
ARCv2 is the next generation ISA from Synopsys and basis for the
HS3{4,6,8} families of processors which retain the traditional ARC mantra of
low power and configurability and are now more performant and feature rich.
HS38x is a 10 stage pipeline core which supports MMU (with huge pages) and
SMP (upto 4 cores) among other features.
+ www.synopsys.com/dw/ipdir.php?ds=arc-hs38-processor
+ http://news.synopsys.com/2014-10-14-New-DesignWare-ARC-HS38-Processor-Doubles-Performance-for-Embedded-Linux-Applications
+ http://www.embedded.com/electronics-news/4435975/Synopsys-ARC-HS38-core-gives-2X-boost-to-Linux-based-apps
- support for ARC SDP (Software Development platform): Main Board + CPU Cards
= AXS101: CPU Card with ARC700 in silicon @ 700 MHz
= AXS103: CPU Card with HS38x in FPGA
- refactoring of ARCompact port to accomodate new ARCv2 ISA
- misc updates/cleanups
* tag 'arc-4.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc: (72 commits)
ARC: Fix build failures for ARCompact in linux-next after ARCv2 support
ARCv2: Allow older gcc to cope with new regime of ARCv2/ARCompact support
ARCv2: [vdk] dts files and defconfig for HS38 VDK
ARCv2: [axs103] Support ARC SDP FPGA platform for HS38x cores
ARC: [axs101] Prepare for AXS103
ARCv2: [nsim*hs*] Support simulation platforms for HS38x cores
ARCv2: All bits in place, allow ARCv2 builds
ARCv2: SLC: Handle explcit flush for DMA ops (w/o IO-coherency)
ARCv2: STAR 9000837815 workaround hardware exclusive transactions livelock
ARC: Reduce bitops lines of code using macros
ARCv2: barriers
arch: conditionally define smp_{mb,rmb,wmb}
ARC: add smp barriers around atomics per Documentation/atomic_ops.txt
ARC: add compiler barrier to LLSC based cmpxchg
ARCv2: SMP: intc: IDU 2nd level intc for dynamic IRQ distribution
ARCv2: SMP: clocksource: Enable Global Real Time counter
ARCv2: SMP: ARConnect debug/robustness
ARCv2: SMP: Support ARConnect (MCIP) for Inter-Core-Interrupts et al
ARC: make plat_smp_ops weak to allow over-rides
ARCv2: clocksource: Introduce 64bit local RTC counter
...
This replaces the plain loop over the sglist array with for_each_sg()
macro which consists of sg_next() function calls. Since arc doesn't
select ARCH_HAS_SG_CHAIN, it is not necessary to use for_each_sg() in
order to loop over each sg element. But this can help find problems with
drivers that do not properly initialize their sg tables when
CONFIG_DEBUG_SG is enabled.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Acked-by: Vineet Gupta <vgupta@synopsys.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull asm/scatterlist.h removal from Jens Axboe:
"We don't have any specific arch scatterlist anymore, since parisc
finally switched over. Kill the include"
* 'for-4.2/sg' of git://git.kernel.dk/linux-block:
remove scatterlist.h generation from arch Kbuild files
remove <asm/scatterlist.h>
CRIU is recreating the process memory layout by remapping the checkpointee
memory area on top of the current process (criu). This includes remapping
the vDSO to the place it has at checkpoint time.
However some architectures like powerpc are keeping a reference to the
vDSO base address to build the signal return stack frame by calling the
vDSO sigreturn service. So once the vDSO has been moved, this reference
is no more valid and the signal frame built later are not usable.
This patch serie is introducing a new mm hook framework, and a new
arch_remap hook which is called when mremap is done and the mm lock still
hold. The next patch is adding the vDSO remap and unmap tracking to the
powerpc architecture.
This patch (of 3):
This patch introduces a new set of header file to manage mm hooks:
- per architecture empty header file (arch/x/include/asm/mm-arch-hooks.h)
- a generic header (include/linux/mm-arch-hooks.h)
The architecture which need to overwrite a hook as to redefine it in its
header file, while architecture which doesn't need have nothing to do.
The default hooks are defined in the generic header and are used in the
case the architecture is not defining it.
In a next step, mm hooks defined in include/asm-generic/mm_hooks.h should
be moved here.
Signed-off-by: Laurent Dufour <ldufour@linux.vnet.ibm.com>
Suggested-by: Andrew Morton <akpm@linux-foundation.org>
Cc: "Kirill A. Shutemov" <kirill.shutemov@linux.intel.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Pavel Emelyanov <xemul@parallels.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
L2 cache on ARCHS processors is called SLC (System Level Cache)
For working DMA (in absence of hardware assisted IO Coherency) we need
to manage SLC explicitly when buffers transition between cpu and
controllers.
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
A quad core SMP build could get into hardware livelock with concurrent
LLOCK/SCOND. Workaround that by adding a PREFETCHW which is serialized by
SCU (System Coherency Unit). It brings the cache line in Exclusive state
and makes others invalidate their lines. This gives enough time for
winner to complete the LLOCK/SCOND, before others can get the line back.
The prefetchw in the ll/sc loop is not nice but this is the only
software workaround for current version of RTL.
Cc: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
ARCv2 based HS38 cores are weakly ordered and thus explicit barriers for
kernel proper.
SMP barrier is provided by DMB instruction which also guarantees local
barrier hence used as backend of smp_*mb() as well as *mb() APIs
Also hookup barriers into MMIO accessors to avoid ordering issues in IO
Cc: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
- arch_spin_lock/unlock were lacking the ACQUIRE/RELEASE barriers
Since ARCv2 only provides load/load, store/store and all/all, we need
the full barrier
- LLOCK/SCOND based atomics, bitops, cmpxchg, which return modified
values were lacking the explicit smp barriers.
- Non LLOCK/SCOND varaints don't need the explicit barriers since that
is implicity provided by the spin locks used to implement the
critical section (the spin lock barriers in turn are also fixed in
this commit as explained above
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: stable@vger.kernel.org
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
When auditing cmpxchg call sites, Chuck noted that gcc was optimizing
away some of the desired LDs.
| do {
| new = old = *ipi_data_ptr;
| new |= 1U << msg;
| } while (cmpxchg(ipi_data_ptr, old, new) != old);
was generating to below
| 8015cef8: ld r2,[r4,0] <-- First LD
| 8015cefc: bset r1,r2,r1
|
| 8015cf00: llock r3,[r4] <-- atomic op
| 8015cf04: brne r3,r2,8015cf10
| 8015cf08: scond r1,[r4]
| 8015cf0c: bnz 8015cf00
|
| 8015cf10: brne r3,r2,8015cf00 <-- Branch doesn't go to orig LD
Although this was fixed by adding a ACCESS_ONCE in this call site, it
seems safer (for now at least) to add compiler barrier to LLSC based
cmpxchg
Reported-by: Chuck Jordan <cjordan@synopsys,com>
Cc: <stable@vger.kernel.org>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Pull x86 core updates from Ingo Molnar:
"There were so many changes in the x86/asm, x86/apic and x86/mm topics
in this cycle that the topical separation of -tip broke down somewhat -
so the result is a more traditional architecture pull request,
collected into the 'x86/core' topic.
The topics were still maintained separately as far as possible, so
bisectability and conceptual separation should still be pretty good -
but there were a handful of merge points to avoid excessive
dependencies (and conflicts) that would have been poorly tested in the
end.
The next cycle will hopefully be much more quiet (or at least will
have fewer dependencies).
The main changes in this cycle were:
* x86/apic changes, with related IRQ core changes: (Jiang Liu, Thomas
Gleixner)
- This is the second and most intrusive part of changes to the x86
interrupt handling - full conversion to hierarchical interrupt
domains:
[IOAPIC domain] -----
|
[MSI domain] --------[Remapping domain] ----- [ Vector domain ]
| (optional) |
[HPET MSI domain] ----- |
|
[DMAR domain] -----------------------------
|
[Legacy domain] -----------------------------
This now reflects the actual hardware and allowed us to distangle
the domain specific code from the underlying parent domain, which
can be optional in the case of interrupt remapping. It's a clear
separation of functionality and removes quite some duct tape
constructs which plugged the remap code between ioapic/msi/hpet
and the vector management.
- Intel IOMMU IRQ remapping enhancements, to allow direct interrupt
injection into guests (Feng Wu)
* x86/asm changes:
- Tons of cleanups and small speedups, micro-optimizations. This
is in preparation to move a good chunk of the low level entry
code from assembly to C code (Denys Vlasenko, Andy Lutomirski,
Brian Gerst)
- Moved all system entry related code to a new home under
arch/x86/entry/ (Ingo Molnar)
- Removal of the fragile and ugly CFI dwarf debuginfo annotations.
Conversion to C will reintroduce many of them - but meanwhile
they are only getting in the way, and the upstream kernel does
not rely on them (Ingo Molnar)
- NOP handling refinements. (Borislav Petkov)
* x86/mm changes:
- Big PAT and MTRR rework: making the code more robust and
preparing to phase out exposing direct MTRR interfaces to drivers -
in favor of using PAT driven interfaces (Toshi Kani, Luis R
Rodriguez, Borislav Petkov)
- New ioremap_wt()/set_memory_wt() interfaces to support
Write-Through cached memory mappings. This is especially
important for good performance on NVDIMM hardware (Toshi Kani)
* x86/ras changes:
- Add support for deferred errors on AMD (Aravind Gopalakrishnan)
This is an important RAS feature which adds hardware support for
poisoned data. That means roughly that the hardware marks data
which it has detected as corrupted but wasn't able to correct, as
poisoned data and raises an APIC interrupt to signal that in the
form of a deferred error. It is the OS's responsibility then to
take proper recovery action and thus prolonge system lifetime as
far as possible.
- Add support for Intel "Local MCE"s: upcoming CPUs will support
CPU-local MCE interrupts, as opposed to the traditional system-
wide broadcasted MCE interrupts (Ashok Raj)
- Misc cleanups (Borislav Petkov)
* x86/platform changes:
- Intel Atom SoC updates
... and lots of other cleanups, fixlets and other changes - see the
shortlog and the Git log for details"
* 'x86-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (222 commits)
x86/hpet: Use proper hpet device number for MSI allocation
x86/hpet: Check for irq==0 when allocating hpet MSI interrupts
x86/mm/pat, drivers/infiniband/ipath: Use arch_phys_wc_add() and require PAT disabled
x86/mm/pat, drivers/media/ivtv: Use arch_phys_wc_add() and require PAT disabled
x86/platform/intel/baytrail: Add comments about why we disabled HPET on Baytrail
genirq: Prevent crash in irq_move_irq()
genirq: Enhance irq_data_to_desc() to support hierarchy irqdomain
iommu, x86: Properly handle posted interrupts for IOMMU hotplug
iommu, x86: Provide irq_remapping_cap() interface
iommu, x86: Setup Posted-Interrupts capability for Intel iommu
iommu, x86: Add cap_pi_support() to detect VT-d PI capability
iommu, x86: Avoid migrating VT-d posted interrupts
iommu, x86: Save the mode (posted or remapped) of an IRTE
iommu, x86: Implement irq_set_vcpu_affinity for intel_ir_chip
iommu: dmar: Provide helper to copy shared irte fields
iommu: dmar: Extend struct irte for VT-d Posted-Interrupts
iommu: Add new member capability to struct irq_remap_ops
x86/asm/entry/64: Disentangle error_entry/exit gsbase/ebx/usermode code
x86/asm/entry/32: Shorten __audit_syscall_entry() args preparation
x86/asm/entry/32: Explain reloading of registers after __audit_syscall_entry()
...
Caveats about cache flush on ARCv2 based cores
- dcache is PIPT so paddr is sufficient for cache maintenance ops (no
need to setup PTAG reg
- icache is still VIPT but only aliasing configs need PTAG setup
So basically this is departure from MMU-v3 which always need vaddr in
line ops registers (DC_IVDL, DC_FLDL, IC_IVIL) but paddr in DC_PTAG,
IC_PTAG respectively.
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
The issue was, on HS when interrupt is taken, IRQ_ACT is set and that is
NOT cleared unless we do RTIE (or manually clear it). Linux interrupt
handling has top and bottom halves. Latter lead to softirqs (which can
reschedule) AND expect interrupts to be REALLY re-enabled which was NOT
happening for us since we only SETI, dont clear IRQ_ACT
So we can have a state when both cores have taken interrupt (IRQ_ACT set),
get rescheduled, both send IPI and wait in CSD lock which will never be
cleared as cores can't take the pending IPI IRQ due to existing IRQ_ACT
set.
So local_irq_enable() now drops the IRQ_ACT.act bit to re-enable IRQs.
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Reported by Anton as LTP:munmap01 failing with Illegal Instruction
Exception.
--------------------->8--------------------------------------
mmap2(NULL, 24576, PROT_READ|PROT_WRITE, MAP_SHARED, 3, 0) = 0x200d2000
munmap(0x200d2000, 24576) = 0
--- SIGSEGV {si_signo=SIGSEGV, si_code=SEGV_MAPERR, si_addr=0x200d2000}
---
potentially unexpected fatal signal 4.
Path: /munmap01
CPU: 0 PID: 61 Comm: munmap01 Not tainted 3.13.0-g5d5c46d9a556 #8
task: 9f1a8000 ti: 9f154000 task.ti: 9f154000
[ECR ]: 0x00020100 => Illegal Insn
[EFA ]: 0x0001354c
[BLINK ]: 0x200515d4
[ERET ]: 0x1354c
@off 0x1354c in [/munmap01]
VMA: 0x00010000 to 0x00018000
[STAT32]: 0x800802c0
...
--------------------->8--------------------------------------
The issue was
1. munmap01 accessed unmapped memory (on purpose) with signal handler
installed for SIGSEGV
2. The faulting instruction happened to be in Delay Slot
00011864 <main>:
11908: bl.d 13284 <tst_resm>
1190c: stb r16,[r2]
3. kernel sets up the reg file for signal handler and correctly clears
the DE bit in pt_regs->status32 placeholder
4. However RESTORE_CALLEE_SAVED_USER macro is not adjusted for ARCv2,
and it over-writes the above with orig/stale value of status32
5. After RTIE, userspace signal handler executes a non branch
instruction with DE bit set, triggering Illegal Instruction Exception.
Reported-by: Anton Kolesov <akolesov@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Previously this macro was overloaded with stack switching, saving SP at right
slot in pt_regs, saving/setup of r25 and setting SP baseline to where
pt_regs->sp is saved (vs. bottom of pt_regs)
Now it only does SP switch, and leaves SP pointing to bottom of pt_regs.
r25 saving is no longer done here to allow for future reordering of
regfile in pt_regs w/o touching this macro
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Elide the need to re-read ECR in Trap handler by ensuring that
EXCEPTION_PROLOGUE does that at the very end just before returning
to Trap handler
ARCv2 EXCEPTION_PROLOGUE already did that, so same for ARcompact and the
common trap handler adjusted to use cached ECR
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Add ioremap_wt() to all arch-specific asm/io.h headers which
define ioremap_wc() locally. These headers do not include
<asm-generic/iomap.h>. Some of them include <asm-generic/io.h>,
but ioremap_wt() is defined for consistency since they define
all ioremap_xxx locally.
In all architectures without Write-Through support, ioremap_wt()
is defined indentical to ioremap_nocache().
frv and m68k already have ioremap_writethrough(). On those we
add ioremap_wt() indetical to ioremap_writethrough() and defines
ARCH_HAS_IOREMAP_WT in both architectures.
The ioremap_wt() interface is exported to drivers.
Signed-off-by: Toshi Kani <toshi.kani@hp.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Elliott@hp.com
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Luis R. Rodriguez <mcgrof@suse.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: arnd@arndb.de
Cc: hch@lst.de
Cc: hmh@hmh.eng.br
Cc: jgross@suse.com
Cc: konrad.wilk@oracle.com
Cc: linux-mm <linux-mm@kvack.org>
Cc: linux-nvdimm@lists.01.org
Cc: stefan.bader@canonical.com
Cc: yigal@plexistor.com
Link: http://lkml.kernel.org/r/1433436928-31903-9-git-send-email-bp@alien8.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
This makes test_bit() more like its siblings *_bit() routines.
Also add some comments about the constant @nr micro-optimization
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
As execution domain support is gone we can remove
signal translation from the signal code and remove
exec_domain from thread_info.
Signed-off-by: Richard Weinberger <richard@nod.at>
The old implementation assumed that SP at the time of __switch_to() is
right above pt_regs which is almost certainly not the case as there will
be some stack build up between entry into kernel and leading up to
__switch_to
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
/proc/<pid>/maps currently don't annotate stack vma with "[stack]"
This is because KSTK_ESP ie expected to return usermode SP of tsk while
currently it returns the kernel mode SP of a sleeping tsk.
While the fix is trivial, we also need to adjust the ARC kernel stack
unwinder to not use KSTK_SP and friends any more.
Cc: <stable@vger.kernel.org>
Reported-and-suggested-by: Alexey Brodkin <abrodkin@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
The arc unwinder can also be used for perf callchains.
Signed-off-by: Mischa Jonker <mjonker@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Some fixes, nothing too exciting this time as well...
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=8o17
-----END PGP SIGNATURE-----
Merge tag 'arc-3.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc
Pull ARC updates from Vineet Gupta:
"Some fixes, nothing too exciting this time as well..."
* tag 'arc-3.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc:
ARC: fix page address calculation if PAGE_OFFSET != LINUX_LINK_BASE
ARC: Fix earlycon build breakage
ARC: Dynamically determine BASE_BAUD from DeviceTree
arc: Remove unused prepare_to_copy()
ARC: use ACCESS_ONCE in cmpxchg loop
ARC: add some more comments to ret_from_fork
ARC: fix /proc/cpuinfo for offline cpus
We used to calculate page address differently in 2 cases:
1. In virt_to_page(x) we do
--->8---
mem_map + (x - CONFIG_LINUX_LINK_BASE) >> PAGE_SHIFT
--->8---
2. In in pte_page(x) we do
--->8---
mem_map + (pte_val(x) - PAGE_OFFSET) >> PAGE_SHIFT
--->8---
That leads to problems in case PAGE_OFFSET != CONFIG_LINUX_LINK_BASE -
different pages will be selected depending on where and how we calculate
page address.
In particular in the STAR 9000853582 when gdb attempted to read memory
of another process it got improper page in get_user_pages() because this
is exactly one of the places where we search for a page by pte_page().
The fix is trivial - we need to calculate page address similarly in both
cases.
Cc: <stable@vger.kernel.org>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
If an attacker can cause a controlled kernel stack overflow, overwriting
the restart block is a very juicy exploit target. This is because the
restart_block is held in the same memory allocation as the kernel stack.
Moving the restart block to struct task_struct prevents this exploit by
making the restart_block harder to locate.
Note that there are other fields in thread_info that are also easy
targets, at least on some architectures.
It's also a decent simplification, since the restart code is more or less
identical on all architectures.
[james.hogan@imgtec.com: metag: align thread_info::supervisor_stack]
Signed-off-by: Andy Lutomirski <luto@amacapital.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Kees Cook <keescook@chromium.org>
Cc: David Miller <davem@davemloft.net>
Acked-by: Richard Weinberger <richard@nod.at>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Haavard Skinnemoen <hskinnemoen@gmail.com>
Cc: Hans-Christian Egtvedt <egtvedt@samfundet.no>
Cc: Steven Miao <realmz6@gmail.com>
Cc: Mark Salter <msalter@redhat.com>
Cc: Aurelien Jacquiot <a-jacquiot@ti.com>
Cc: Mikael Starvik <starvik@axis.com>
Cc: Jesper Nilsson <jesper.nilsson@axis.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Richard Kuo <rkuo@codeaurora.org>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Jonas Bonn <jonas@southpole.se>
Cc: "James E.J. Bottomley" <jejb@parisc-linux.org>
Cc: Helge Deller <deller@gmx.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Acked-by: Michael Ellerman <mpe@ellerman.id.au> (powerpc)
Tested-by: Michael Ellerman <mpe@ellerman.id.au> (powerpc)
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Chen Liqin <liqin.linux@gmail.com>
Cc: Lennox Wu <lennox.wu@gmail.com>
Cc: Chris Metcalf <cmetcalf@ezchip.com>
Cc: Guan Xuetao <gxt@mprc.pku.edu.cn>
Cc: Chris Zankel <chris@zankel.net>
Cc: Max Filippov <jcmvbkbc@gmail.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
LKP has triggered a compiler warning after my recent patch "mm: account
pmd page tables to the process":
mm/mmap.c: In function 'exit_mmap':
>> mm/mmap.c:2857:2: warning: right shift count >= width of type [enabled by default]
The code:
> 2857 WARN_ON(mm_nr_pmds(mm) >
2858 round_up(FIRST_USER_ADDRESS, PUD_SIZE) >> PUD_SHIFT);
In this, on tile, we have FIRST_USER_ADDRESS defined as 0. round_up() has
the same type -- int. PUD_SHIFT.
I think the best way to fix it is to define FIRST_USER_ADDRESS as unsigned
long. On every arch for consistency.
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Reported-by: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
8250 earlycon is broken on multi-platform ARC because the UART clk
value (BASE_BAUD) is fixed at build time.
Instead, determine the appropriate UART clk at runtime; parse the
devicetree early for platforms requiring alternate UART clk values
(currently only the TB10X platform).
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: linux-serial@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: Rob Herring <robh@kernel.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
prepare_to_copy() was removed from all architectures supported at that
time in commit 55ccf3fe3f ("fork: move the real prepare_to_copy()
users to arch_dup_task_struct()"). Remove it from arc as well.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)
iQIcBAABAgAGBQJUkrnWAAoJEGnX8d3iisJenj4P/30RohNJG6Apu2bPFcFOrDz5
yc8TbKEh8VLgxm28e5MDEOUKvNV84noXrD+835Y1Ch5K9G9yDOiw7z3auargVCB1
NXEy8zVQboOQJahL0WnlKoUQxz6zTV7BjC6b5TICQtzxCniQ86inh0w7n6GtUfI4
cGuE+gthf+gWLENsoFE6OpMqidA2NTvs//qFZA/26xNvZHuL4/kBcMh1Jyp1Oa37
xZewIA9wdD2n9P2escFgzyzORf5GBEfG4r2StIol0XFKPzDZugkCwS9+dsLFTJdf
e/5y/JFOhZ2vlIppvHTqEpCXzWF6Llnyg6s2uWkwlajxGgqciZzkVOVq6dFJf99t
PBSMs4DNDQDCUBgO4PT8X9YC9U3N2B3wGSTNSsEykh/0aJpxHEWpQp2MXrW8lin7
SzwmVS5bapjlE3NI2tHw5lyfGgxYXiEqTs77rqXJfVmdsBehCBE6hvJELHPlHTd5
Ng/12NsJJqUh5sNX+wSEgwkTEX31WtZbQq9BpdYixP5kmgu0ptahRBMfJuHzjtL/
wWwVu9mOOWiVGIGPYL2uq+lLts4Ytb+p7WOEbS+jL+En8vheUKxi8cE3vYI7tjwn
d8N/Q7fp9wHQCB1EzE9pKR02g/++IxEmTCAfWsMIv9BnECp/kgugx7yul9NAdU5D
dq63tGI0Uoz9nt6n/khi
=Q9WJ
-----END PGP SIGNATURE-----
Merge tag 'arc-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc
Pull arch/arc updates from Vineet Gupta:
"Minor updates for ARC for 3.19"
* tag 'arc-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc:
ARC: rename default defconfig
ARC: [nsimosci] move peripherals to match model to FPGA
ARC: document memory clobber in irq control macros
ARC: R-M-W assist locks only needed for !LLSC
ARC: add power management options
Pull networking updates from David Miller:
1) New offloading infrastructure and example 'rocker' driver for
offloading of switching and routing to hardware.
This work was done by a large group of dedicated individuals, not
limited to: Scott Feldman, Jiri Pirko, Thomas Graf, John Fastabend,
Jamal Hadi Salim, Andy Gospodarek, Florian Fainelli, Roopa Prabhu
2) Start making the networking operate on IOV iterators instead of
modifying iov objects in-situ during transfers. Thanks to Al Viro
and Herbert Xu.
3) A set of new netlink interfaces for the TIPC stack, from Richard
Alpe.
4) Remove unnecessary looping during ipv6 routing lookups, from Martin
KaFai Lau.
5) Add PAUSE frame generation support to gianfar driver, from Matei
Pavaluca.
6) Allow for larger reordering levels in TCP, which are easily
achievable in the real world right now, from Eric Dumazet.
7) Add a variable of napi_schedule that doesn't need to disable cpu
interrupts, from Eric Dumazet.
8) Use a doubly linked list to optimize neigh_parms_release(), from
Nicolas Dichtel.
9) Various enhancements to the kernel BPF verifier, and allow eBPF
programs to actually be attached to sockets. From Alexei
Starovoitov.
10) Support TSO/LSO in sunvnet driver, from David L Stevens.
11) Allow controlling ECN usage via routing metrics, from Florian
Westphal.
12) Remote checksum offload, from Tom Herbert.
13) Add split-header receive, BQL, and xmit_more support to amd-xgbe
driver, from Thomas Lendacky.
14) Add MPLS support to openvswitch, from Simon Horman.
15) Support wildcard tunnel endpoints in ipv6 tunnels, from Steffen
Klassert.
16) Do gro flushes on a per-device basis using a timer, from Eric
Dumazet. This tries to resolve the conflicting goals between the
desired handling of bulk vs. RPC-like traffic.
17) Allow userspace to ask for the CPU upon what a packet was
received/steered, via SO_INCOMING_CPU. From Eric Dumazet.
18) Limit GSO packets to half the current congestion window, from Eric
Dumazet.
19) Add a generic helper so that all drivers set their RSS keys in a
consistent way, from Eric Dumazet.
20) Add xmit_more support to enic driver, from Govindarajulu
Varadarajan.
21) Add VLAN packet scheduler action, from Jiri Pirko.
22) Support configurable RSS hash functions via ethtool, from Eyal
Perry.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1820 commits)
Fix race condition between vxlan_sock_add and vxlan_sock_release
net/macb: fix compilation warning for print_hex_dump() called with skb->mac_header
net/mlx4: Add support for A0 steering
net/mlx4: Refactor QUERY_PORT
net/mlx4_core: Add explicit error message when rule doesn't meet configuration
net/mlx4: Add A0 hybrid steering
net/mlx4: Add mlx4_bitmap zone allocator
net/mlx4: Add a check if there are too many reserved QPs
net/mlx4: Change QP allocation scheme
net/mlx4_core: Use tasklet for user-space CQ completion events
net/mlx4_core: Mask out host side virtualization features for guests
net/mlx4_en: Set csum level for encapsulated packets
be2net: Export tunnel offloads only when a VxLAN tunnel is created
gianfar: Fix dma check map error when DMA_API_DEBUG is enabled
cxgb4/csiostor: Don't use MASTER_MUST for fw_hello call
net: fec: only enable mdio interrupt before phy device link up
net: fec: clear all interrupt events to support i.MX6SX
net: fec: reset fep link status in suspend function
net: sock: fix access via invalid file descriptor
net: introduce helper macro for_each_cmsghdr
...
As there are now no remaining users of arch_fast_hash(), lets kill
it entirely.
This basically reverts commit 71ae8aac3e ("lib: introduce arch
optimized hash library") and follow-up work, that is f.e., commit
237217546d ("lib: hash: follow-up fixups for arch hash"),
commit e3fec2f74f ("lib: Add missing arch generic-y entries for
asm-generic/hash.h") and last but not least commit 6a02652df5
("perf tools: Fix include for non x86 architectures").
Cc: Francesco Fusco <fusco@ntop.org>
Cc: Thomas Graf <tgraf@suug.ch>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While there normally is no reason to have a pull request for asm-generic
but have all changes get merged through whichever tree needs them, I do
have a series for 3.19. There are two sets of patches that change
significant portions of asm/io.h, and this branch contains both in order
to resolve the conflicts:
- Will Deacon has done a set of patches to ensure that all architectures
define {read,write}{b,w,l,q}_relaxed() functions or get them by
including asm-generic/io.h. These functions are commonly used on ARM
specific drivers to avoid expensive L2 cache synchronization implied by
the normal {read,write}{b,w,l,q}, but we need to define them on all
architectures in order to share the drivers across architectures and
to enable CONFIG_COMPILE_TEST configurations for them
- Thierry Reding has done an unrelated set of patches that extends
the asm-generic/io.h file to the degree necessary to make it useful
on ARM64 and potentially other architectures.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=xUv6
-----END PGP SIGNATURE-----
Merge tag 'asm-generic-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic
Pull asm-generic asm/io.h rewrite from Arnd Bergmann:
"While there normally is no reason to have a pull request for
asm-generic but have all changes get merged through whichever tree
needs them, I do have a series for 3.19.
There are two sets of patches that change significant portions of
asm/io.h, and this branch contains both in order to resolve the
conflicts:
- Will Deacon has done a set of patches to ensure that all
architectures define {read,write}{b,w,l,q}_relaxed() functions or
get them by including asm-generic/io.h.
These functions are commonly used on ARM specific drivers to avoid
expensive L2 cache synchronization implied by the normal
{read,write}{b,w,l,q}, but we need to define them on all
architectures in order to share the drivers across architectures
and to enable CONFIG_COMPILE_TEST configurations for them
- Thierry Reding has done an unrelated set of patches that extends
the asm-generic/io.h file to the degree necessary to make it useful
on ARM64 and potentially other architectures"
* tag 'asm-generic-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic: (29 commits)
ARM64: use GENERIC_PCI_IOMAP
sparc: io: remove duplicate relaxed accessors on sparc32
ARM: sa11x0: Use void __iomem * in MMIO accessors
arm64: Use include/asm-generic/io.h
ARM: Use include/asm-generic/io.h
asm-generic/io.h: Implement generic {read,write}s*()
asm-generic/io.h: Reconcile I/O accessor overrides
/dev/mem: Use more consistent data types
Change xlate_dev_{kmem,mem}_ptr() prototypes
ARM: ixp4xx: Properly override I/O accessors
ARM: ixp4xx: Fix build with IXP4XX_INDIRECT_PCI
ARM: ebsa110: Properly override I/O accessors
ARC: Remove redundant PCI_IOBASE declaration
documentation: memory-barriers: clarify relaxed io accessor semantics
x86: io: implement dummy relaxed accessor macros for writes
tile: io: implement dummy relaxed accessor macros for writes
sparc: io: implement dummy relaxed accessor macros for writes
powerpc: io: implement dummy relaxed accessor macros for writes
parisc: io: implement dummy relaxed accessor macros for writes
mn10300: io: implement dummy relaxed accessor macros for writes
...
ARC's asm/io.h includes the asm-generic/io.h which already defines the
PCI_IOBASE variable in exactly the same way, so it can be dropped from
the architecture specific header.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Updated Boot printing
kgdb update for arc gdb 7.5
Bug fixes (some marked for stable)
More code refactoring/consolidation
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=236F
-----END PGP SIGNATURE-----
Merge tag 'arc-3.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc
Pull ARC updates from Vineet Gupta:
"Sorry for the late pull request. Current stuff was ready for a while
but I was hoping to squeeze in support for almost ready ARC SDP
platform (and avoid a 2nd pull request), however it seems there are
still some loose ends which warrant more time.
- Platform code reduction/moving-up (TB10X no longer needs any
callbacks)
- updated boot printing
- kgdb update for arc gdb 7.5
- bug fixes (some marked for stable)
- more code refactoring/consolidation"
* tag 'arc-3.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc:
ARC: boot: cpu feature print enhancements
ARC: boot: consolidate cross-checking of h/w and s/w
ARC: unbork FPU save/restore
ARC: remove extraneous __KERNEL__ guards
ARC: Update order of registers in KGDB to match GDB 7.5
ARC: Remove unneeded Kconfig entry NO_DMA
ARC: BUG() dumps stack after @msg (@msg now same as in generic BUG))
ARC: refactoring: reduce the scope of some local vars
ARC: remove gcc mpy heuristics
ARC: RIP @running_on_hw
ARC: Update comments about uncached address space
ARC: rename kconfig option for unaligned emulation
ARC: [nsimosci] Allow "headless" models to boot
ARC: [arcfpga] Get rid of ARC_BOARD_ANGEL4 and ARC_BOARD_ML509
ARC: [arcfpga] Remove more dead code
ARC: [plat*] move code out of .init_machine into common
ARC: [arcfpga] consolidate machine description, DT
ARC: Allow SMP kernel to build/boot on UP-only infrastructure
Pull arch atomic cleanups from Ingo Molnar:
"This is a series kept separate from the main locking tree, which
cleans up and improves various details in the atomics type handling:
- Remove the unused atomic_or_long() method
- Consolidate and compress atomic ops implementations between
architectures, to reduce linecount and to make it easier to add new
ops.
- Rewrite generic atomic support to only require cmpxchg() from an
architecture - generate all other methods from that"
* 'locking-arch-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (23 commits)
locking,arch: Use ACCESS_ONCE() instead of cast to volatile in atomic_read()
locking, mips: Fix atomics
locking, sparc64: Fix atomics
locking,arch: Rewrite generic atomic support
locking,arch,xtensa: Fold atomic_ops
locking,arch,sparc: Fold atomic_ops
locking,arch,sh: Fold atomic_ops
locking,arch,powerpc: Fold atomic_ops
locking,arch,parisc: Fold atomic_ops
locking,arch,mn10300: Fold atomic_ops
locking,arch,mips: Fold atomic_ops
locking,arch,metag: Fold atomic_ops
locking,arch,m68k: Fold atomic_ops
locking,arch,m32r: Fold atomic_ops
locking,arch,ia64: Fold atomic_ops
locking,arch,hexagon: Fold atomic_ops
locking,arch,cris: Fold atomic_ops
locking,arch,avr32: Fold atomic_ops
locking,arch,arm64: Fold atomic_ops
locking,arch,arm: Fold atomic_ops
...
Order of registers has changed in GDB moving from 6.8 to 7.5. This patch
updates KGDB to work properly with GDB 7.5, though makes it incompatible
with 6.8.
Signed-off-by: Anton Kolesov <Anton.Kolesov@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Cc: <stable@vger.kernel.org> #3.10, 3.12, 3.14, 3.16
ARC specific version (doesn't panic) still makes sense so that generic
code calling BUG doesn't panic and helps debugging more
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
* No active users of this flag anymore
* flag itself was no longer usable with new simualtor which acts just like
hardware, not providing the special chip-id = 0xffff which good old
ISS used to do.
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
In light of recent SNAFU with SMP build, allow simple platform to build
as SMP but run UP.
* Remove the dependence on simulation SMP extension to enable quick
build/test iterations of SMP kernel.
* In absence of platform SMP registration, prevent the NULL smp feature
name from borkign the system
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
The nohz full code needs irq work to trigger its own interrupt so that
the subsystem can work even when the tick is stopped.
Lets introduce arch_irq_work_has_interrupt() that archs can override to
tell about their support for this ability.
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Many of the atomic op implementations are the same except for one
instruction; fold the lot into a few CPP macros and reduce LoC.
This also prepares for easy addition of new ops.
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Link: http://lkml.kernel.org/r/20140508135851.886055622@infradead.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Mostly cleanup/refactoring in core intc, cache flush, IPI send...
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=Mx5r
-----END PGP SIGNATURE-----
Merge tag 'arc-v3.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc
Pull ARC changes from Vineet Gupta:
"Mostly cleanup/refactoring in core intc, cache flush, IPI send..."
* tag 'arc-v3.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc:
mm, arc: remove obsolete pagefault oom killer comment
ARC: help gcc elide icache helper for !SMP
ARC: move common ops for line/full cache into helpers
ARC: cache boot reporting updates
ARC: [intc] mask/unmask can be hidden again
ARC: [plat-arcfpga] No need for init_irq hack
ARC: [intc] don't mask all IRQ by default
ARC: prune extra header includes from smp.c
ARC: update some comments
ARC: [SMP] unify cpu private IRQ requests (TIMER/IPI)
* print aliasing or not, VIPT/PIPT etc
* compress param storage using bitfields
* more use of IS_ENABLED to de-uglify code
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
The current cpu-private IRQ registration is ugly as it requires need to
expose arch_unmask_irq() outside of intc code.
So switch to percpu IRQ APIs:
-request_percpu_irq [boot core]
-enable_percpu_irq [all cores]
Encapsulated in helper arc_request_percpu_irq()
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
The arch_mutex_cpu_relax() function, introduced by 34b133f, is
hacky and ugly. It was added a few years ago to address the fact
that common cpu_relax() calls include yielding on s390, and thus
impact the optimistic spinning functionality of mutexes. Nowadays
we use this function well beyond mutexes: rwsem, qrwlock, mcs and
lockref. Since the macro that defines the call is in the mutex header,
any users must include mutex.h and the naming is misleading as well.
This patch (i) renames the call to cpu_relax_lowlatency ("relax, but
only if you can do it with very low latency") and (ii) defines it in
each arch's asm/processor.h local header, just like for regular cpu_relax
functions. On all archs, except s390, cpu_relax_lowlatency is simply cpu_relax,
and thus we can take it out of mutex.h. While this can seem redundant,
I believe it is a good choice as it allows us to move out arch specific
logic from generic locking primitives and enables future(?) archs to
transparently define it, similarly to System Z.
Signed-off-by: Davidlohr Bueso <davidlohr@hp.com>
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Anton Blanchard <anton@samba.org>
Cc: Aurelien Jacquiot <a-jacquiot@ti.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Bharat Bhushan <r65777@freescale.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Chen Liqin <liqin.linux@gmail.com>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: Chris Zankel <chris@zankel.net>
Cc: David Howells <dhowells@redhat.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Deepthi Dharwar <deepthi@linux.vnet.ibm.com>
Cc: Dominik Dingel <dingel@linux.vnet.ibm.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Guan Xuetao <gxt@mprc.pku.edu.cn>
Cc: Haavard Skinnemoen <hskinnemoen@gmail.com>
Cc: Hans-Christian Egtvedt <egtvedt@samfundet.no>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Helge Deller <deller@gmx.de>
Cc: Hirokazu Takata <takata@linux-m32r.org>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: James E.J. Bottomley <jejb@parisc-linux.org>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Jason Wang <jasowang@redhat.com>
Cc: Jesper Nilsson <jesper.nilsson@axis.com>
Cc: Joe Perches <joe@perches.com>
Cc: Jonas Bonn <jonas@southpole.se>
Cc: Joseph Myers <joseph@codesourcery.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: Koichi Yasutake <yasutake.koichi@jp.panasonic.com>
Cc: Lennox Wu <lennox.wu@gmail.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mark Salter <msalter@redhat.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Max Filippov <jcmvbkbc@gmail.com>
Cc: Michael Neuling <mikey@neuling.org>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Mikael Starvik <starvik@axis.com>
Cc: Nicolas Pitre <nico@linaro.org>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Qais Yousef <qais.yousef@imgtec.com>
Cc: Qiaowei Ren <qiaowei.ren@intel.com>
Cc: Rafael Wysocki <rafael.j.wysocki@intel.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Richard Kuo <rkuo@codeaurora.org>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Steven Miao <realmz6@gmail.com>
Cc: Steven Rostedt <srostedt@redhat.com>
Cc: Stratos Karafotis <stratosk@semaphore.gr>
Cc: Tim Chen <tim.c.chen@linux.intel.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Vasily Kulikov <segoon@openwall.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Vineet Gupta <Vineet.Gupta1@synopsys.com>
Cc: Waiman Long <Waiman.Long@hp.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Wolfram Sang <wsa@the-dreams.de>
Cc: adi-buildroot-devel@lists.sourceforge.net
Cc: linux390@de.ibm.com
Cc: linux-alpha@vger.kernel.org
Cc: linux-am33-list@redhat.com
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-c6x-dev@linux-c6x.org
Cc: linux-cris-kernel@axis.com
Cc: linux-hexagon@vger.kernel.org
Cc: linux-ia64@vger.kernel.org
Cc: linux@lists.openrisc.net
Cc: linux-m32r-ja@ml.linux-m32r.org
Cc: linux-m32r@ml.linux-m32r.org
Cc: linux-m68k@lists.linux-m68k.org
Cc: linux-metag@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: linux-parisc@vger.kernel.org
Cc: linuxppc-dev@lists.ozlabs.org
Cc: linux-s390@vger.kernel.org
Cc: linux-sh@vger.kernel.org
Cc: linux-xtensa@linux-xtensa.org
Cc: sparclinux@vger.kernel.org
Link: http://lkml.kernel.org/r/1404079773.2619.4.camel@buesod1.americas.hpqcorp.net
Signed-off-by: Ingo Molnar <mingo@kernel.org>
This patch adds implementation of GET_THREAD_AREA ptrace request type. This
is required by GDB to debug NPTL applications.
Signed-off-by: Anton Kolesov <Anton.Kolesov@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
There's no Kconfig symbol ARC_MMU_V4 so the checks for CONFIG_ARC_MMU_V4
will always evaluate to false. Remove them.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
* Moving cache disabling to early boot
* ARC UART enabled only if earlyprintk setup in cmdline
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=neQc
-----END PGP SIGNATURE-----
Merge tag 'arc-v3.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc
Pull ARC updates from Vineet Gupta:
"Nothing too exciting here, just minor fixes/cleanup. Only noteworthy
ones are:
- Moving cache disabling to early boot
- ARC UART enabled only if earlyprintk setup in cmdline"
* tag 'arc-v3.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc:
ARC: Disable caches in early boot if so configured
ARC: [arcfpga] Early ARC UART to be only activated by cmdline
ARC: [arcfpga] Get rid of legacy BVCI latency unit support
ARC: remove duplicate header exports
ARC: arc_local_timer_setup() need not pass own cpu id
ARC: Fixed spelling errors within comments
ARC: make start_thread() out-of-line
ARC: fix mmuv2 warning
ARC: [SMP] ISS SMP extension bitrot
- Another round of clean-up of FDT related code in architecture code.
This removes knowledge of internal FDT details from most architectures
except powerpc.
- Conversion of kernel's custom FDT parsing code to use libfdt.
- DT based initialization for generic serial earlycon. The introduction
of generic serial earlycon support went in thru tty tree.
- Improve the platform device naming for DT probed devices to ensure
unique naming and use parent names instead of a global index.
- Fix a race condition in of_update_property.
- Unify the various linker section OF match tables and fix several
function prototype errors.
- Update platform_get_irq_byname to work in deferred probe cases.
- 2 binding doc updates
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJTjzgyAAoJEMhvYp4jgsXiFsUH/1PMTGo8CyD62VQD5ZKdAoW+
Fq6vCiRQ8assF5i5ZLcW1DqhjtoRaCKYhVbRKa5lj7cZdjlSpacI/qQPrF5Br2Ii
bTE3Ff/AQwipQaz/Bj7HqJCgGwfWK8xdfgW0abKsyXMWDN86Bov/zzeu8apmws0x
H1XjJRgnc/rzM4m9ny6+lss0iq6YL54SuTYNzHR33+Ywxls69SfHXIhCW0KpZcBl
5U3YUOomt40GfO46sxFA4xApAhypEK4oVq7asyiA2ArTZ/c2Pkc9p5CBqzhDLmlq
yioWTwHIISv0q+yMLCuQrVGIsbUDkQyy7RQ15z6U+/e/iGO/M+j3A5yxMc3qOi4=
=Onff
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-3.16' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux into next
Pull DeviceTree updates from Rob Herring:
- Another round of clean-up of FDT related code in architecture code.
This removes knowledge of internal FDT details from most
architectures except powerpc.
- Conversion of kernel's custom FDT parsing code to use libfdt.
- DT based initialization for generic serial earlycon. The
introduction of generic serial earlycon support went in through the
tty tree.
- Improve the platform device naming for DT probed devices to ensure
unique naming and use parent names instead of a global index.
- Fix a race condition in of_update_property.
- Unify the various linker section OF match tables and fix several
function prototype errors.
- Update platform_get_irq_byname to work in deferred probe cases.
- 2 binding doc updates
* tag 'devicetree-for-3.16' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (58 commits)
of: handle NULL node in next_child iterators
of/irq: provide more wrappers for !CONFIG_OF
devicetree: bindings: Document micrel vendor prefix
dt: bindings: dwc2: fix required value for the phy-names property
of_pci_irq: kill useless variable in of_irq_parse_pci()
of/irq: do irq resolution in platform_get_irq_byname()
of: Add a testcase for of_find_node_by_path()
of: Make of_find_node_by_path() handle /aliases
of: Create unlocked version of for_each_child_of_node()
lib: add glibc style strchrnul() variant
of: Handle memory@0 node on PPC32 only
pci/of: Remove dead code
of: fix race between search and remove in of_update_property()
of: Use NULL for pointers
of: Stop naming platform_device using dcr address
of: Ensure unique names without sacrificing determinism
tty/serial: pl011: add DT based earlycon support
of/fdt: add FDT serial scanning for earlycon
of/fdt: add FDT address translation support
serial: earlycon: add DT support
...
Unify the various architectures __dtb_start and __dtb_end definitions
moving them into of_fdt.h.
Signed-off-by: Rob Herring <robh@kernel.org>
Acked-by: Vineet Gupta <vgupta@synopsys.com>
Acked-by: James Hogan <james.hogan@imgtec.com>
Tested-by: Michal Simek <michal.simek@xilinx.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Jonas Bonn <jonas@southpole.se>
Cc: Chris Zankel <chris@zankel.net>
Cc: Max Filippov <jcmvbkbc@gmail.com>
Cc: linux-metag@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: linux@lists.openrisc.net
Cc: linux-xtensa@linux-xtensa.org
Tested-by: Grant Likely <grant.likely@linaro.org>
Tested-by: Stephen Chivers <schivers@csc.com>
Commit 93ea02bb84 ("arch: Clean up asm/barrier.h implementations")
wired generic barrier.h for ARC, but failed to delete the existing file.
In 3.15, due to rcupdate.h updates, this causes a build breakage on ARC:
CC arch/arc/kernel/asm-offsets.s
In file included from include/linux/sched.h:45:0,
from arch/arc/kernel/asm-offsets.c:9:
include/linux/rculist.h: In function __list_add_rcu:
include/linux/rculist.h:54:2: error: implicit declaration of function smp_store_release [-Werror=implicit-function-declaration]
rcu_assign_pointer(list_next_rcu(prev), new);
^
Cc: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The arc mb() implementation is a compiler barrier(), therefore it all
doesn't matter one way or the other. Simply remove the existing
definitions and use whatever is generated by the defaults.
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Link: http://lkml.kernel.org/n/tip-ua48a59wri3ybz1rz8i7uvbr@git.kernel.org
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Both already use asm-generic/barrier.h as per their
include/asm/Kbuild. Remove the stale files.
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Link: http://lkml.kernel.org/n/tip-c7vlkshl3tblim0o8z2p70kt@git.kernel.org
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Richard Kuo <rkuo@codeaurora.org>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: linux-hexagon@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
* Support for external initrd from Noam
* Fix broken serial console in nsimosci Virtual Platform
* Reuse of ENTRY/END assembler macros across hand asm code
* Other minor fixes here and there
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)
iQIcBAABAgAGBQJTQo6NAAoJEGnX8d3iisJeNTkP/jwPKxaDx88xbyUK0+OtmB9o
v6BLhRI/mzdXf4KX7aq+0B3II1niYvD9e65LnQlx/f+fExyiaeIucxI4rKcFsbYH
X1MBOKe1FNcFUhu6xSeRs1IVXR9z9bU4+H9K2U38RhZHBQtb9apDFUqTJoNy6PEP
PO0nkwB8vaeoocVdCRWD574d8eQpUYejo5pNesQG4zLClO0IafYiP0vQWXB4dGjh
ppfq+UR0GfXYwFgO+JbSoJFg0SmQuw02LoQ6vFZbtvZ3l7nfmv+F4SJKzDQR++vq
nV9Z++cSdBsgDD+7nFeo1VlDkFsJY3148yFSfqf79E4JIn3VQyFFmzHasDR6GjYn
HCW7WS9OFYmcnG6WUsH5EyJK/QbuNFHRE0kxbJap2AnYsXyQkdDkAZqQWNeG4TmO
SI8YKMAWh2CcH0FOKntcGPmlOvyi//C28mAPKKsqO/D7YShGkhhWZG1BpbX4Vb1u
0YFuignfAk/R6RckBXKymguRA7kloj+cI7KkvzkWmfkzJzh8qSrp6UwR8A/UwiDb
U+ZSL3WOBaA5Hc4sU+58uUDIxPcob034vgQpxNXWAmGg3QJ62j+EGinGsj9fw3XV
EyXTIYIDByriMu5winn9Xj7KLyaI7YZb+3HAFO76whlHD+sMAiLzKMKLUKfD8z42
5e4R9+CsDpwnK3iCi1P5
=dmgU
-----END PGP SIGNATURE-----
Merge tag 'arc-v3.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc
Pull ARC changes from Vineet Gupta:
- Support for external initrd from Noam
- Fix broken serial console in nsimosci Virtual Platform
- Reuse of ENTRY/END assembler macros across hand asm code
- Other minor fixes here and there
* tag 'arc-v3.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc:
ARC: [nsimosci] Unbork console
ARC: [nsimosci] Change .dts to use generic 8250 UART
ARC: [SMP] General Fixes
ARC: Remove unused DT template file
ARC: [clockevent] simplify timer ISR
ARC: [clockevent] can't be SoC specific
ARC: Remove ARC_HAS_COH_RTSC
ARC: switch to generic ENTRY/END assembler annotations
ARC: support external initrd
ARC: add uImage to .gitignore
ARC: [arcfpga] Fix __initconst data const-correctness
With commit 9df62f0544 "arch: use ASM_NL instead of ';'" the generic
macros can handle the arch specific newline quirk. Hence we can get rid
of ARC asm macros and use the "C" style macros.
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
This patch allows each architecture to add its specific assembly optimized
arch_mcs_spin_lock_contended and arch_mcs_spinlock_uncontended for
MCS lock and unlock functions.
Signed-off-by: Tim Chen <tim.c.chen@linux.intel.com>
Cc: Scott J Norton <scott.norton@hp.com>
Cc: Raghavendra K T <raghavendra.kt@linux.vnet.ibm.com>
Cc: AswinChandramouleeswaran <aswin@hp.com>
Cc: George Spelvin <linux@horizon.com>
Cc: Rik vanRiel <riel@redhat.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: MichelLespinasse <walken@google.com>
Cc: Peter Hurley <peter@hurleysoftware.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Alex Shi <alex.shi@linaro.org>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Tim Chen <tim.c.chen@linux.intel.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: "Figo.zhang" <figo1802@gmail.com>
Cc: "Paul E.McKenney" <paulmck@linux.vnet.ibm.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Davidlohr Bueso <davidlohr.bueso@hp.com>
Cc: Waiman Long <waiman.long@hp.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Matthew R Wilcox <matthew.r.wilcox@intel.com>
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/1390347382.3138.67.camel@schen9-DESK
Signed-off-by: Ingo Molnar <mingo@kernel.org>
We perform a clean up of the Kbuid files in each architecture.
We order the files in each Kbuild in alphabetical order
by running the below script.
for i in arch/*/include/asm/Kbuild
do
cat $i | gawk '/^generic-y/ {
i = 3;
do {
for (; i <= NF; i++) {
if ($i == "\\") {
getline;
i = 1;
continue;
}
if ($i != "")
hdr[$i] = $i;
}
break;
} while (1);
next;
}
// {
print $0;
}
END {
n = asort(hdr);
for (i = 1; i <= n; i++)
print "generic-y += " hdr[i];
}' > ${i}.sorted;
mv ${i}.sorted $i;
done
Signed-off-by: Tim Chen <tim.c.chen@linux.intel.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Matthew R Wilcox <matthew.r.wilcox@intel.com>
Cc: AswinChandramouleeswaran <aswin@hp.com>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: "Paul E.McKenney" <paulmck@linux.vnet.ibm.com>
Cc: Scott J Norton <scott.norton@hp.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: "Figo.zhang" <figo1802@gmail.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Rik van Riel <riel@redhat.com>
Cc: Waiman Long <waiman.long@hp.com>
Cc: Peter Hurley <peter@hurleysoftware.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Tim Chen <tim.c.chen@linux.intel.com>
Cc: Alex Shi <alex.shi@linaro.org>
Cc: Raghavendra K T <raghavendra.kt@linux.vnet.ibm.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: George Spelvin <linux@horizon.com>
Cc: MichelLespinasse <walken@google.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Davidlohr Bueso <davidlohr.bueso@hp.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
[ Fixed build bug. ]
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Vineet Gupta