Gitee limit the repo's size to 3GB, to reduce the size of the code,
sync codes to ock 5.4.119-20.0009.21 in one commit.
Signed-off-by: Jianping Liu <frankjpliu@tencent.com>
- Fix Tegra OF node reference leak (Nishka Dasgupta)
- Add #defines for PCIe Data Link Feature and Physical Layer 16.0 GT/s
features (Vidya Sagar)
- Disable MSI for Tegra Root Ports since they don't support using MSI for
all Root Port events (Vidya Sagar)
- Group DesignWare write-protected register writes together (Vidya Sagar)
- Move DesignWare capability search interfaces so they can be used by
both host and endpoint drivers (Vidya Sagar)
- Add DesignWare extended capability search interfaces (Vidya Sagar)
- Export dw_pcie_wait_for_link() so drivers can be modules (Vidya Sagar)
- Add "snps,enable-cdm-check" DT binding for Configuration Dependent
Module (CDM) register checking (Vidya Sagar)
- Add DesignWare support for "snps,enable-cdm-check" CDM checking (Vidya
Sagar)
- Add "supports-clkreq" DT binding for host drivers to decide whether to
advertise low power features (Vidya Sagar)
- Add DT binding for Tegra194 (Vidya Sagar)
- Add DT binding for Tegra194 P2U (PIPE to UPHY) block (Vidya Sagar)
- Add support for Tegra194 P2U (PIPE to UPHY) (Vidya Sagar)
- Add support for Tegra194 host controller (Vidya Sagar)
- Add Tegra support for sideband PERST# and CLKREQ# for C5 (Vidya Sagar)
- Add Tegra support for slot regulators for p2972-0000 platform (Vidya
Sagar)
* lorenzo/pci/tegra:
arm64: tegra: Add PCIe slot supply information in p2972-0000 platform
arm64: tegra: Add configuration for PCIe C5 sideband signals
PCI: tegra: Add support to enable slot regulators
PCI: tegra: Add support to configure sideband pins
dt-bindings: PCI: tegra: Add PCIe slot supplies regulator entries
dt-bindings: PCI: tegra: Add sideband pins configuration entries
PCI: tegra: Add Tegra194 PCIe support
phy: tegra: Add PCIe PIPE2UPHY support
dt-bindings: PHY: P2U: Add Tegra194 P2U block
dt-bindings: PCI: tegra: Add device tree support for Tegra194
dt-bindings: Add PCIe supports-clkreq property
PCI: dwc: Add support to enable CDM register check
dt-bindings: PCI: designware: Add binding for CDM register check
PCI: dwc: Export dw_pcie_wait_for_link() API
PCI: dwc: Add extended configuration space capability search API
PCI: dwc: Move config space capability search API
PCI: dwc: Group DBI registers writes requiring unlocking
PCI: Disable MSI for Tegra root ports
PCI: Add #defines for some of PCIe spec r4.0 features
PCI: tegra: Fix OF node reference leak
- Add mediatek support for MT7629 (Jianjun Wang)
* remotes/lorenzo/pci/mediatek:
PCI: mediatek: Add controller support for MT7629
dt-bindings: PCI: Add support for MT7629
- Make kirin_dw_pcie_ops constant (Nishka Dasgupta)
- Make DesignWare "num-lanes" property optional and remove from relevant
DTs (Hou Zhiqiang)
* remotes/lorenzo/pci/dwc:
arm64: dts: fsl: Remove num-lanes property from PCIe nodes
ARM: dts: ls1021a: Remove num-lanes property from PCIe nodes
PCI: dwc: Return directly when num-lanes is not found
dt-bindings: PCI: designware: Remove the num-lanes from Required properties
PCI: kirin: Make structure kirin_dw_pcie_ops constant
- A bunch of DT binding conversions to DT schema format
- Clean-ups of the Arm idle-states binding
- Support a default number of cells in of_for_each_phandle() when the
cells name is missing
- Expose dtbs_check and dt_binding_check in the make help
- Convert writting-schema.md to ReST
- HiSilicon reset controller binding updates
- Add documentation for MT8516 RNG
-----BEGIN PGP SIGNATURE-----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=ZO6c
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull Devicetree updates from Rob Herring:
- a bunch of DT binding conversions to DT schema format
- clean-ups of the Arm idle-states binding
- support a default number of cells in of_for_each_phandle() when the
cells name is missing
- expose dtbs_check and dt_binding_check in the make help
- convert writting-schema.md to ReST
- HiSilicon reset controller binding updates
- add documentation for MT8516 RNG
* tag 'devicetree-for-5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (46 commits)
of: restore old handling of cells_name=NULL in of_*_phandle_with_args()
bus: qcom: fix spelling mistake "ambigous" -> "ambiguous"
of: Let of_for_each_phandle fallback to non-negative cell_count
iommu: pass cell_count = -1 to of_for_each_phandle with cells_name
dt-bindings: arm: Convert Realtek board/soc bindings to json-schema
dt-bindings: arm: Convert Actions Semi bindings to jsonschema
dt-bindings: Correct spelling in example schema
dt-bindings: cpu: Add a support cpu type for cortex-a55
dt-bindings: gpu: mali-midgard: Add samsung exynos5250 compatible
dt-bindings: arm: idle-states: Move exit-latency-us explanation
dt-bindings: arm: idle-states: Add punctuation to improve readability
dt-bindings: arm: idle-states: Correct "constraint guarantees"
dt-bindings: arm: idle-states: Correct references to wake-up delay
dt-bindings: arm: idle-states: Use "e.g." and "i.e." consistently
pinctrl-mcp23s08: Fix property-name in dt-example
dt-bindings: Clarify interrupts-extended usage
dt-bindings: Convert Arm Mali Utgard GPU to DT schema
dt-bindings: Convert Arm Mali Bifrost GPU to DT schema
dt-bindings: Convert Arm Mali Midgard GPU to DT schema
dt-bindings: irq: Convert Allwinner NMI Controller to a schema
...
Add optional bindings "vpcie3v3-supply" and "vpcie12v-supply" to describe
regulators of a PCIe slot's supplies 3.3V and 12V provided the platform
is designed to have regulator controlled slot supplies.
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Thierry Reding <treding@nvidia.com>
Add optional bindings "pinctrl-names" and "pinctrl-0" to describe pin
configuration information of a particular PCIe controller.
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Thierry Reding <treding@nvidia.com>
Armada CP110 PCIe controller can have from one to four PHYs for
configuring SERDES lanes (PCIe x1, PCIe x2 or PCIe x4). Describe the
phys and phy-names properties in the bindings.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The num-lanes is not a mandatory property, e.g. on FSL
Layerscape SoCs, the PCIe link training is completed
automatically based on the selected SerDes protocol, it
does not need the num-lanes to set-up the link width.
Currently it is both a Required and Optional property,
let's remove it from the Required properties.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
The unit-address must match the first address specified in the
reg property of the node.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Add support for Tegra194 PCIe controllers. These controllers are based
on Synopsys DesignWare core IP.
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Thierry Reding <treding@nvidia.com>
Some host controllers need to know the existence of clkreq signal routing
to downstream devices to be able to advertise low power features like
ASPM L1 substates. Without clkreq signal routing being present, enabling
ASPM L1 substates might lead to downstream devices being disconnected
from the bus. Hence a new device tree property 'supports-clkreq' is added
to make such host controllers aware of clkreq signal routing to
downstream devices.
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Add support to enable CDM (Configuration Dependent Module) registers check
for any data corruption. CDM registers include standard PCIe configuration
space registers, Port Logic registers and iATU and DMA registers.
Refer Section S.4 of Synopsys DesignWare Cores PCI Express Controller Databook
Version 4.90a.
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Rob Herring <robh@kernel.org>
MT7629 is an ARM based platform SoC integrating the same PCIe IP as
MT7622, add a binding for it.
Signed-off-by: Jianjun Wang <jianjun.wang@mediatek.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Ryder Lee <ryder.lee@mediatek.com>
- Reorganize Tegra AFI/PHY/REFCLK/etc functions (Manikanta Maddireddy)
- Mask Tegra AFI_INTR in runtime suspend (Manikanta Maddireddy)
- Fix Tegra AFI/PCIe powerup sequence (Manikanta Maddireddy)
- Add Tegra124, Tegra132, Tegra210, and Tegra186 support for Gen2 link
speed (Manikanta Maddireddy)
- Advertise Tegra AER support (Manikanta Maddireddy)
- Program Tegra210 UPHY settings (Manikanta Maddireddy)
- Enable Tegra opportunistic UpdateFC and ACK (Manikanta Maddireddy)
- Disable Tegra AFI dynamic clock gating (Manikanta Maddireddy)
- Process Tegra pending DLL transactions before entering L1 or L2 to
prevent receiver errors (Manikanta Maddireddy)
- Enable Tegra xclk clock clamping in L1 (Manikanta Maddireddy)
- Increase Tegra deskew retry time (Manikanta Maddireddy)
- Work around Tegra hardware RAW erratum (Manikanta Maddireddy)
- Update Tegra210 flow control timer frequency (Manikanta Maddireddy)
- Work around Tegra Gen1/Gen2 link number negotiation issue (Manikanta
Maddireddy)
- Work around Tegra PLLE power down issue (Manikanta Maddireddy)
- Program Tegra20 to support cacheable upstream transactions (Manikanta
Maddireddy)
- Log Tegra PRSNT_SENSE_IRQ as debug, not err (Manikanta Maddireddy)
- Add register offset for third Root Port on Tegra186 and Tegra30
(Manikanta Maddireddy)
- Document Tegra PCIe DPD pinctrl property (Manikanta Maddireddy)
- Put Tegra PEX CLK & BIAS pads in DPD mode to reduce power usage when
powergated (Manikanta Maddireddy)
- Add generic DT binding for "reset-gpios" property (Manikanta
Maddireddy)
- Add Tegra support for GPIO-based PERST# (Manikanta Maddireddy)
- Enable Relaxed Ordering only for Tegra20 & Tegra30 (Vidya Sagar)
* remotes/lorenzo/pci/tegra:
PCI: tegra: Enable Relaxed Ordering only for Tegra20 & Tegra30
PCI: tegra: Change link retry log level to debug
PCI: tegra: Add support for GPIO based PERST#
PCI: Add DT binding for "reset-gpios" property
PCI: tegra: Put PEX CLK & BIAS pads in DPD mode
dt-bindings: pci: tegra: Document PCIe DPD pinctrl optional prop
PCI: tegra: Add AFI_PEX2_CTRL reg offset as part of SoC struct
PCI: tegra: Change PRSNT_SENSE IRQ log to debug
PCI: tegra: Program AFI_CACHE_BAR_{0,1}_{ST,SZ} registers only for Tegra20
PCI: tegra: Fix PLLE power down issue due to CLKREQ# signal
PCI: tegra: Set target speed as Gen1 before starting LTSSM
PCI: tegra: Update flow control timer frequency in Tegra210
PCI: tegra: Add SW fixup for RAW violations
PCI: tegra: Increase the deskew retry time
PCI: tegra: Enable PCIe xclk clock clamping
PCI: tegra: Process pending DLL transactions before entering L1 or L2
PCI: tegra: Disable AFI dynamic clock gating
PCI: tegra: Enable opportunistic UpdateFC and ACK
PCI: tegra: Program UPHY electrical settings for Tegra210
PCI: tegra: Advertise PCIe Advanced Error Reporting (AER) capability
PCI: tegra: Add PCIe Gen2 link speed support
PCI: tegra: Fix PCIe host power up sequence
PCI: tegra: Mask AFI_INTR in runtime suspend
PCI: tegra: Rearrange Tegra PCIe driver functions
PCI: tegra: Handle failure cases in tegra_pcie_power_on()
soc/tegra: pmc: Export tegra_powergate_power_on()
- Move qcom driver to bulk clock API (Bjorn Andersson)
- Add Qualcomm QCS404 PCIe controller support (Bjorn Andersson)
- Ensure Qualcomm PERST is asserted for at least 100ms (Niklas Cassel)
* remotes/lorenzo/pci/qcom:
PCI: qcom: Ensure that PERST is asserted for at least 100 ms
PCI: qcom: Add QCS404 PCIe controller support
dt-bindings: PCI: qcom: Add QCS404 to the binding
PCI: qcom: Use clk bulk API for 2.4.0 controllers
- DT binding schema examples are now validated against the schemas.
Various examples are fixed due to that.
- Sync dtc with upstream version v1.5.0-30-g702c1b6c0e73
- Initial schemas for networking bindings. This includes ethernet, phy
and mdio common bindings with several Allwinner and stmmac converted
to the schema.
- Conversion of more Arm top-level SoC/board bindings to DT schema
- Conversion of PSCI binding to DT schema
- Rework Arm CPU schema to coexist with other CPU schemas
- Add a bunch of missing vendor prefixes and new ones for SoChip,
Sipeed, Kontron, B&R Industrial Automation GmbH, and Espressif
- Add Mediatek UART RX wakeup support to binding
- Add reset to ST UART binding
- Remove some Linuxisms from the endianness common-properties.txt
binding
- Make the flattened DT read-only after init
- Ignore disabled reserved memory nodes
- Clean-up some dead code in FDT functions
-----BEGIN PGP SIGNATURE-----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=Qpuw
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull Devicetree updates from Rob Herring:
- DT binding schema examples are now validated against the schemas.
Various examples are fixed due to that.
- Sync dtc with upstream version v1.5.0-30-g702c1b6c0e73
- Initial schemas for networking bindings. This includes ethernet, phy
and mdio common bindings with several Allwinner and stmmac converted
to the schema.
- Conversion of more Arm top-level SoC/board bindings to DT schema
- Conversion of PSCI binding to DT schema
- Rework Arm CPU schema to coexist with other CPU schemas
- Add a bunch of missing vendor prefixes and new ones for SoChip,
Sipeed, Kontron, B&R Industrial Automation GmbH, and Espressif
- Add Mediatek UART RX wakeup support to binding
- Add reset to ST UART binding
- Remove some Linuxisms from the endianness common-properties.txt
binding
- Make the flattened DT read-only after init
- Ignore disabled reserved memory nodes
- Clean-up some dead code in FDT functions
* tag 'devicetree-for-5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (56 commits)
dt-bindings: vendor-prefixes: add Sipeed
dt-bindings: vendor-prefixes: add SoChip
dt-bindings: 83xx-512x-pci: Drop cell-index property
dt-bindings: serial: add documentation for Rx in-band wakeup support
dt-bindings: arm: Convert RDA Micro board/soc bindings to json-schema
of: unittest: simplify getting the adapter of a client
of/fdt: pass early_init_dt_reserve_memory_arch() with bool type nomap
of/platform: Drop superfluous cast in of_device_make_bus_id()
dt-bindings: usb: ehci: Fix example warnings
dt-bindings: net: Use phy-mode instead of phy-connection-type
dt-bindings: simple-framebuffer: Add requirement for pipelines
dt-bindings: display: Fix simple-framebuffer example
dt-bindings: net: mdio: Add child nodes
dt-bindings: net: mdio: Add address and size cells
dt-bindings: net: mdio: Add a nodename pattern
dt-bindings: mtd: sunxi-nand: Drop 'maxItems' from child 'reg' property
dt-bindings: arm: Limit cpus schema to only check Arm 'cpu' nodes
dt-bindings: backlight: lm3630a: correct schema validation
dt-bindings: net: dwmac: Deprecate the PHY reset properties
dt-bindings: net: sun8i-emac: Convert the binding to a schemas
...
28eac2b74c ("powerpc/fsl: Remove cell-index from PCI nodes"),
and for now it is still not used, drop it from doc.
Cc: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Change the "gpio_slave" and "apb_csr" to optional, the "gpio_slave"
is not used in current code, and "apb_csr" is not used by some platforms.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Subrahmanya Lingappa <l.subrahmanya@mobiveil.co.in>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Minghuan Lian <Minghuan.Lian@nxp.com>
Reviewed-by: Subrahmanya Lingappa <l.subrahmanya@mobiveil.co.in>
Add PCIe support for the RZ/G2M (a.k.a. R8A774A1).
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Mostly due to x86 and acpi conversion, several documentation
links are still pointing to the old file. Fix them.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Reviewed-by: Wolfram Sang <wsa@the-dreams.de>
Reviewed-by: Sven Van Asbroeck <TheSven73@gmail.com>
Reviewed-by: Bhupesh Sharma <bhsharma@redhat.com>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
The Qualcomm QCS404 platform contains a PCIe controller, add this to the
Qualcomm PCI binding document. The controller is the same version as the
one used in IPQ4019, but the PHY part is described separately, hence the
difference in clocks and resets.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
- Move IRQ register address computation inside macros (Kishon Vijay
Abraham I)
- Separate legacy IRQ and MSI configuration (Kishon Vijay Abraham I)
- Use hwirq, not virq, to get MSI IRQ number offset (Kishon Vijay Abraham
I)
- Squash ks_pcie_handle_msi_irq() into ks_pcie_msi_irq_handler() (Kishon
Vijay Abraham I)
- Add dwc support for platforms with custom MSI controllers (Kishon Vijay
Abraham I)
- Add keystone-specific MSI controller (Kishon Vijay Abraham I)
- Remove dwc host_ops previously used for keystone-specific MSI (Kishon
Vijay Abraham I)
- Skip dwc default MSI init if platform has custom MSI controller (Kishon
Vijay Abraham I)
- Implement .start_link() and .stop_link() for keystone endpoint support
(Kishon Vijay Abraham I)
- Add keystone "reg-names" DT binding (Kishon Vijay Abraham I)
- Squash ks_pcie_dw_host_init() into ks_pcie_add_pcie_port() (Kishon
Vijay Abraham I)
- Get keystone register resources from DT by name, not index (Kishon
Vijay Abraham I)
- Get DT resources in .probe() to prepare for endpoint support (Kishon
Vijay Abraham I)
- Add "ti,syscon-pcie-mode" DT property for PCIe mode configuration
(Kishon Vijay Abraham I)
- Explicitly set keystone to host mode (Kishon Vijay Abraham I)
- Document DT "atu" reg-names requirement for DesignWare core >= 4.80
(Kishon Vijay Abraham I)
- Enable dwc iATU unroll for endpoint mode as well as host mode (Kishon
Vijay Abraham I)
- Add dwc "version" to identify core >= 4.80 for ATU programming (Kishon
Vijay Abraham I)
- Don't build ARM32-specific keystone code on ARM64 (Kishon Vijay Abraham
I)
- Add DT binding for keystone PCIe RC in AM654 SoC (Kishon Vijay Abraham
I)
- Add keystone support for AM654 SoC PCIe RC (Kishon Vijay Abraham I)
- Reset keystone PHYs before enabling them (Kishon Vijay Abraham I)
- Make of_pci_get_max_link_speed() available to endpoint drivers as well
as host drivers (Kishon Vijay Abraham I)
- Add keystone support for DT "max-link-speed" property (Kishon Vijay
Abraham I)
- Add endpoint library support for BAR buffer alignment (Kishon Vijay
Abraham I)
- Make all dw_pcie_ep_ops structs const (Kishon Vijay Abraham I)
- Fix fencepost error in dw_pcie_ep_find_capability() (Kishon Vijay
Abraham I)
- Add dwc hooks for dbi/dbi2 that share the same address space (Kishon
Vijay Abraham I)
- Add keystone support for TI AM654x in endpoint mode (Kishon Vijay
Abraham I)
- Configure designware endpoints to advertise smallest resizable BAR
(1MB) (Kishon Vijay Abraham I)
- Align designware endpoint ATU windows for raising MSIs (Kishon Vijay
Abraham I)
- Add endpoint test support for TI AM654x (Kishon Vijay Abraham I)
- Fix endpoint test test_reg_bar issue (Kishon Vijay Abraham I)
* remotes/lorenzo/pci/keystone:
misc: pci_endpoint_test: Fix test_reg_bar to be updated in pci_endpoint_test
misc: pci_endpoint_test: Add support to test PCI EP in AM654x
PCI: designware-ep: Use aligned ATU window for raising MSI interrupts
PCI: designware-ep: Configure Resizable BAR cap to advertise the smallest size
PCI: keystone: Add support for PCIe EP in AM654x Platforms
dt-bindings: PCI: Add PCI EP DT binding documentation for AM654
PCI: dwc: Add callbacks for accessing dbi2 address space
PCI: dwc: Fix dw_pcie_ep_find_capability() to return correct capability offset
PCI: dwc: Add const qualifier to struct dw_pcie_ep_ops
PCI: endpoint: Add support to specify alignment for buffers allocated to BARs
PCI: keystone: Add support to set the max link speed from DT
PCI: OF: Allow of_pci_get_max_link_speed() to be used by PCI Endpoint drivers
PCI: keystone: Invoke phy_reset() API before enabling PHY
PCI: keystone: Add support for PCIe RC in AM654x Platforms
dt-bindings: PCI: Add PCI RC DT binding documentation for AM654
PCI: keystone: Prevent ARM32 specific code to be compiled for ARM64
PCI: dwc: Fix ATU identification for designware version >= 4.80
PCI: dwc: Enable iATU unroll for endpoint too
dt-bindings: PCI: Document "atu" reg-names
PCI: keystone: Explicitly set the PCIe mode
dt-bindings: PCI: Add dt-binding to configure PCIe mode
PCI: keystone: Move resources initialization to prepare for EP support
PCI: keystone: Use platform_get_resource_byname() to get memory resources
PCI: keystone: Perform host initialization in a single function
dt-bindings: PCI: keystone: Add "reg-names" binding information
PCI: keystone: Cleanup error_irq configuration
PCI: keystone: Add start_link()/stop_link() dw_pcie_ops
PCI: dwc: Remove default MSI initialization for platform specific MSI chips
PCI: dwc: Remove Keystone specific dw_pcie_host_ops
PCI: keystone: Use Keystone specific msi_irq_chip
PCI: dwc: Add support to use non default msi_irq_chip
PCI: keystone: Cleanup ks_pcie_msi_irq_handler()
PCI: keystone: Use hwirq to get the MSI IRQ number offset
PCI: keystone: Add separate functions for configuring MSI and legacy interrupt
PCI: keystone: Cleanup interrupt related macros
# Conflicts:
# drivers/pci/controller/dwc/pcie-designware.h
Add devicetree binding documentation for PCIe in EP mode present in
AM654 SoC.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Add devicetree binding documentation for PCIe in RC mode present in
AM654 SoC.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Document "atu" reg-names required to get the register space for ATU in
Synopsys designware core version >= 4.80.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Add "ti,syscon-pcie-mode" dt-binding to hold phandle to the syscon
register that should be used to configure PCIe in RC mode or EP mode.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Provide a way for the firmware to tell the OS which devices are external to
the machine and therefore untrusted. The property can describe for example
Thunderbolt and other user-accessible ports, which should always have the
strongest IOMMU protection.
Signed-off-by: Jean-Philippe Brucker <jean-philippe.brucker@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Grant Likely <grant.likely@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Add "reg-names" binding information in order for device tree node
to be populated with the correct register strings.
This will break old DT compatibility. However Keystone PCI has never
worked in upstream kernel due to lack of SERDES support, so, before
SERDES support is added, cleanup the Keystone PCI dt-bindings.
This new binding will also be used by PCI in AM654 platform.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
- Use memcpy_fromio()/memcpy_toio() instead of plain memcpy() in PCI
endpoint framework (Wen Yang)
- Add interface to discover supported endpoint features to replace a
bitfield that wasn't flexible enough (Kishon Vijay Abraham I)
- Implement the new supported-feature interface for designware-plat,
dra7xx, rockchip, cadence (Kishon Vijay Abraham I)
- Fix issues with 64-bit BAR in endpoints (Kishon Vijay Abraham I)
- Add layerscape endpoint mode support (Xiaowei Bao)
* remotes/lorenzo/pci/endpoint:
misc: pci_endpoint_test: Add the layerscape EP device support
PCI: layerscape: Add EP mode support
arm64: dts: Add the PCIE EP node in dts
dt-bindings: add DT binding for the layerscape PCIe controller with EP mode
PCI: endpoint: Remove features member in struct pci_epc
PCI: designware-plat: Remove setting epc->features in Designware plat EP driver
PCI: rockchip: Remove pci_epf_linkup() from Rockchip EP driver
PCI: cadence: Remove pci_epf_linkup() from Cadence EP driver
PCI: pci-epf-test: Use pci_epc_get_features() to get EPC features
PCI: pci-epf-test: Do not allocate next BARs memory if current BAR is 64Bit
PCI: pci-epf-test: Remove setting epf_bar flags in function driver
PCI: endpoint: Fix pci_epf_alloc_space() to set correct MEM TYPE flags
PCI: endpoint: Add helper to get first unreserved BAR
PCI: cadence: Populate ->get_features() cdns_pcie_epc_ops
PCI: rockchip: Populate ->get_features() dw_pcie_ep_ops
PCI: pci-dra7xx: Populate ->get_features() dw_pcie_ep_ops
PCI: designware-plat: Populate ->get_features() dw_pcie_ep_ops
PCI: dwc: Add ->get_features() callback function to dw_pcie_ep_ops
PCI: endpoint: Add new pci_epc_ops to get EPC features
PCI: endpoint: functions: Use memcpy_fromio()/memcpy_toio()
- Add dra72x/dra74x/dra76x SoC compatible strings (Kishon Vijay
Abraham I)
- Enable x2 mode support for dra72x/dra74x/dra76x SoC (Kishon Vijay
Abraham I)
- Configure dra7xx PHY to PCIe mode (Kishon Vijay Abraham I)
- Simplify dwc (remove unnecessary header includes, name variables
consistently, reduce inverted logic, etc) (Gustavo Pimentel)
- Add i.MX8MQ support (Andrey Smirnov)
- Add message to help debug dwc MSI-X mask bit errors (Gustavo Pimentel)
- Work around imx7d PCIe PLL erratum (Trent Piepho)
- Don't assert qcom reset GPIO during probe (Bjorn Andersson)
- Skip dwc MSI init if MSIs have been disabled (Lucas Stach)
* remotes/lorenzo/pci/dwc:
PCI: dwc: skip MSI init if MSIs have been explicitly disabled
PCI: dwc: Remove superfluous shifting in definitions
PCI: dwc: Make use of GENMASK/FIELD_PREP
PCI: dwc: Make use of BIT() in constant definitions
PCI: dwc: Share code for dw_pcie_rd/wr_other_conf()
PCI: dwc: Make use of IS_ALIGNED()
PCI: imx6: Add code to request/control "pcie_aux" clock for i.MX8MQ
dt-bindings: imx6q-pcie: Add "pcie_aux" clock for imx8mq
PCI: qcom: Don't deassert reset GPIO during probe
PCI: imx: Add workaround for e10728, IMX7d PCIe PLL failure
ARM: dts: imx7d: Add node for PCIe PHY
dt-bindings: imx6q-pcie: Add description of imx7d pcie phy
PCI: dwc: Print debug error message when MSI-X entry control mask bit is set
PCI: imx6: Add support for i.MX8MQ
PCI: imx6: Convert DIRECT_SPEED_CHANGE quirk code to use a flag
PCI: imx6: Mark PHY functions as i.MX6 specific
PCI: imx6: Introduce drvdata
PCI: dwc: Replace bit rotation operation (1 << bit) with BIT(bit)
PCI: dwc: Improve code readability and simplify mask/unmask operations
PCI: dwc: Rename variable name from data to d on dw_pcie_irq_domain_free()
PCI: dwc: Rename variable name from data to d on dw_pci_msi_set_affinity()
PCI: dwc: Rename variable name from data to d on dw_pci_setup_msi_msg()
PCI: dwc: Rename variable name from data to d on dw_pci_bottom_mask/unmask()
PCI: dwc: Remove unnecessary header include (signal.h)
PCI: dwc: Remove unnecessary header include (of_gpio.h)
PCI: dwc: dra7xx: Invoke phy_set_mode() API to set PHY mode to PHY_MODE_PCIE
PCI: dwc: dra7xx: Enable x2 mode support for dra74x, dra76x and dra72x
dt-bindings: PCI: dra7xx: Add properties to enable x2 lane in dra7
dt-bindings: PCI: dra7xx: Add SoC specific compatible strings
Add support for altr,pcie-root-port-2.0.
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Add the documentation for the Device Tree binding for the layerscape PCIe
controller with EP mode.
Signed-off-by: Xiaowei Bao <xiaowei.bao@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Minghuan Lian <minghuan.lian@nxp.com>
Reviewed-by: Zhiqiang Hou <zhiqiang.hou@nxp.com>
Reviewed-by: Rob Herring <robh+dt@kernel.org>
There is a separate PHY device with its own registers on imx7d. It's
currently unused, but a PCIe erratum on imx7d will require it for the
workaround.
Signed-off-by: Trent Piepho <tpiepho@impinj.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Lucas Stach <l.stach@pengutronix.de>
Add PCIe support for the RZ/G2E (a.k.a. R8A774C0).
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Add syscon properties required for configuring PCIe in x2 lane mode.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Add new compatible strings for dra74x SoC (also used by dra76x) and
dra72x. This can be used to perform SoC specific configuration
(like configuring PCIe in x2 lane mode).
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Rob Herring <robh@kernel.org>
Jianping Liu