Commit Graph

5 Commits

Author SHA1 Message Date
Jianping Liu c62d6b571d ock: sync codes to ock 5.4.119-20.0009.21
Gitee limit the repo's size to 3GB, to reduce the size of the code,
sync codes to ock 5.4.119-20.0009.21 in one commit.

Signed-off-by: Jianping Liu <frankjpliu@tencent.com>
2024-06-11 20:27:38 +08:00
Jianping Liu be16237b31 tkernel: add base tlinux kernel interfaces
Sync kernel codes to the same with 590eaf1fec ("Init Repo base on
linux 5.4.32 long term, and add base tlinux kernel interfaces."), which
is from tk4, and it is the base of tk4.

Signed-off-by: Jianping Liu <frankjpliu@tencent.com>
2024-06-11 20:09:33 +08:00
Joakim Zhang c12c0288e3 perf/imx_ddr: Add support for AXI ID filtering
AXI filtering is used by events 0x41 and 0x42 to count reads or writes
with an ARID or AWID matching a specified filter. The filter is exposed
to userspace as an (ID, MASK) pair, where each set bit in the mask
causes the corresponding bit in the ID to be ignored when matching
against the ID of memory transactions for the purposes of incrementing
the counter.

For example:

  # perf stat -a -e imx8_ddr0/axid-read,axi_mask=0xff,axi_id=0x800/ cmd

will count all read transactions from AXI IDs 0x800 - 0x8ff. If the
'axi_mask' is omitted, then it is treated as 0x0 which means that the
'axi_id' will be matched exactly.

Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Signed-off-by: Will Deacon <will@kernel.org>
2019-08-28 14:16:55 +01:00
Leonard Crestez 4b9ace9c25 perf/imx_ddr: Add MODULE_DEVICE_TABLE
This is required for automatic probing when driver is built as a module.

Fixes: 9a66d36cc7 ("drivers/perf: imx_ddr: Add DDR performance counter support to perf")
Acked-by: Frank Li <frank.li@nxp.com>
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Will Deacon <will@kernel.org>
2019-07-31 17:15:16 +01:00
Frank Li 9a66d36cc7 drivers/perf: imx_ddr: Add DDR performance counter support to perf
Add DDR performance monitor support for iMX8QXP. The PMU consists of 3
programmable event counters and a single dedicated cycle counter.

Example usage:

 $ perf stat -a -e \
   imx8_ddr0/read-cycles/,imx8_ddr0/write-cycles/,imx8_ddr0/precharge/ ls

- or -

 $ perf stat -a -e \
   imx8_ddr0/cycles/,imx8_ddr0/read-access/,imx8_ddr0/write-access/ ls

Other events are supported, and advertised via perf list.

Reviewed-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
[will: rewrote commit message/kconfig and used #defines for dev/cpuhp names]
Signed-off-by: Will Deacon <will.deacon@arm.com>
2019-06-13 11:07:57 +01:00