powerpc/of-device-tree: Factor MTD physmap bindings out of booting-without-of
It's easier to find bindings descriptions in separate files. So factor out the MTD physmap bindings into a separate file to not clutter booting-without-of.txt more. Signed-off-by: Stefan Roese <sr@denx.de> Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This commit is contained in:
Stefan Roese
Grant Likely
parent
4124010292
commit
efcc2da3fd
|
|
@ -43,12 +43,11 @@ Table of Contents
|
|||
2) Representing devices without a current OF specification
|
||||
a) PHY nodes
|
||||
b) Interrupt controllers
|
||||
c) CFI or JEDEC memory-mapped NOR flash
|
||||
d) 4xx/Axon EMAC ethernet nodes
|
||||
e) Xilinx IP cores
|
||||
f) USB EHCI controllers
|
||||
g) MDIO on GPIOs
|
||||
h) SPI busses
|
||||
c) 4xx/Axon EMAC ethernet nodes
|
||||
d) Xilinx IP cores
|
||||
e) USB EHCI controllers
|
||||
f) MDIO on GPIOs
|
||||
g) SPI busses
|
||||
|
||||
VII - Marvell Discovery mv64[345]6x System Controller chips
|
||||
1) The /system-controller node
|
||||
|
|
@ -999,7 +998,7 @@ compatibility.
|
|||
translation of SOC addresses for memory mapped SOC registers.
|
||||
- bus-frequency: Contains the bus frequency for the SOC node.
|
||||
Typically, the value of this field is filled in by the boot
|
||||
loader.
|
||||
loader.
|
||||
|
||||
|
||||
Recommended properties:
|
||||
|
|
@ -1287,71 +1286,7 @@ platforms are moved over to use the flattened-device-tree model.
|
|||
device_type = "open-pic";
|
||||
};
|
||||
|
||||
c) CFI or JEDEC memory-mapped NOR flash
|
||||
|
||||
Flash chips (Memory Technology Devices) are often used for solid state
|
||||
file systems on embedded devices.
|
||||
|
||||
- compatible : should contain the specific model of flash chip(s)
|
||||
used, if known, followed by either "cfi-flash" or "jedec-flash"
|
||||
- reg : Address range of the flash chip
|
||||
- bank-width : Width (in bytes) of the flash bank. Equal to the
|
||||
device width times the number of interleaved chips.
|
||||
- device-width : (optional) Width of a single flash chip. If
|
||||
omitted, assumed to be equal to 'bank-width'.
|
||||
- #address-cells, #size-cells : Must be present if the flash has
|
||||
sub-nodes representing partitions (see below). In this case
|
||||
both #address-cells and #size-cells must be equal to 1.
|
||||
|
||||
For JEDEC compatible devices, the following additional properties
|
||||
are defined:
|
||||
|
||||
- vendor-id : Contains the flash chip's vendor id (1 byte).
|
||||
- device-id : Contains the flash chip's device id (1 byte).
|
||||
|
||||
In addition to the information on the flash bank itself, the
|
||||
device tree may optionally contain additional information
|
||||
describing partitions of the flash address space. This can be
|
||||
used on platforms which have strong conventions about which
|
||||
portions of the flash are used for what purposes, but which don't
|
||||
use an on-flash partition table such as RedBoot.
|
||||
|
||||
Each partition is represented as a sub-node of the flash device.
|
||||
Each node's name represents the name of the corresponding
|
||||
partition of the flash device.
|
||||
|
||||
Flash partitions
|
||||
- reg : The partition's offset and size within the flash bank.
|
||||
- label : (optional) The label / name for this flash partition.
|
||||
If omitted, the label is taken from the node name (excluding
|
||||
the unit address).
|
||||
- read-only : (optional) This parameter, if present, is a hint to
|
||||
Linux that this flash partition should only be mounted
|
||||
read-only. This is usually used for flash partitions
|
||||
containing early-boot firmware images or data which should not
|
||||
be clobbered.
|
||||
|
||||
Example:
|
||||
|
||||
flash@ff000000 {
|
||||
compatible = "amd,am29lv128ml", "cfi-flash";
|
||||
reg = <ff000000 01000000>;
|
||||
bank-width = <4>;
|
||||
device-width = <1>;
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
fs@0 {
|
||||
label = "fs";
|
||||
reg = <0 f80000>;
|
||||
};
|
||||
firmware@f80000 {
|
||||
label ="firmware";
|
||||
reg = <f80000 80000>;
|
||||
read-only;
|
||||
};
|
||||
};
|
||||
|
||||
d) 4xx/Axon EMAC ethernet nodes
|
||||
c) 4xx/Axon EMAC ethernet nodes
|
||||
|
||||
The EMAC ethernet controller in IBM and AMCC 4xx chips, and also
|
||||
the Axon bridge. To operate this needs to interact with a ths
|
||||
|
|
@ -1499,7 +1434,7 @@ platforms are moved over to use the flattened-device-tree model.
|
|||
available.
|
||||
For Axon: 0x0000012a
|
||||
|
||||
e) Xilinx IP cores
|
||||
d) Xilinx IP cores
|
||||
|
||||
The Xilinx EDK toolchain ships with a set of IP cores (devices) for use
|
||||
in Xilinx Spartan and Virtex FPGAs. The devices cover the whole range
|
||||
|
|
@ -1761,7 +1696,7 @@ platforms are moved over to use the flattened-device-tree model.
|
|||
listed above, nodes for these devices should include a phy-handle
|
||||
property, and may include other common network device properties
|
||||
like local-mac-address.
|
||||
|
||||
|
||||
iv) Xilinx Uartlite
|
||||
|
||||
Xilinx uartlite devices are simple fixed speed serial ports.
|
||||
|
|
@ -1793,7 +1728,7 @@ platforms are moved over to use the flattened-device-tree model.
|
|||
- reg-offset : A value of 3 is required
|
||||
- reg-shift : A value of 2 is required
|
||||
|
||||
f) USB EHCI controllers
|
||||
e) USB EHCI controllers
|
||||
|
||||
Required properties:
|
||||
- compatible : should be "usb-ehci".
|
||||
|
|
@ -1819,7 +1754,7 @@ platforms are moved over to use the flattened-device-tree model.
|
|||
big-endian;
|
||||
};
|
||||
|
||||
g) MDIO on GPIOs
|
||||
f) MDIO on GPIOs
|
||||
|
||||
Currently defined compatibles:
|
||||
- virtual,gpio-mdio
|
||||
|
|
@ -1839,7 +1774,7 @@ platforms are moved over to use the flattened-device-tree model.
|
|||
&qe_pio_c 6>;
|
||||
};
|
||||
|
||||
h) SPI (Serial Peripheral Interface) busses
|
||||
g) SPI (Serial Peripheral Interface) busses
|
||||
|
||||
SPI busses can be described with a node for the SPI master device
|
||||
and a set of child nodes for each SPI slave on the bus. For this
|
||||
|
|
|
|||
|
|
@ -0,0 +1,63 @@
|
|||
CFI or JEDEC memory-mapped NOR flash
|
||||
|
||||
Flash chips (Memory Technology Devices) are often used for solid state
|
||||
file systems on embedded devices.
|
||||
|
||||
- compatible : should contain the specific model of flash chip(s)
|
||||
used, if known, followed by either "cfi-flash" or "jedec-flash"
|
||||
- reg : Address range of the flash chip
|
||||
- bank-width : Width (in bytes) of the flash bank. Equal to the
|
||||
device width times the number of interleaved chips.
|
||||
- device-width : (optional) Width of a single flash chip. If
|
||||
omitted, assumed to be equal to 'bank-width'.
|
||||
- #address-cells, #size-cells : Must be present if the flash has
|
||||
sub-nodes representing partitions (see below). In this case
|
||||
both #address-cells and #size-cells must be equal to 1.
|
||||
|
||||
For JEDEC compatible devices, the following additional properties
|
||||
are defined:
|
||||
|
||||
- vendor-id : Contains the flash chip's vendor id (1 byte).
|
||||
- device-id : Contains the flash chip's device id (1 byte).
|
||||
|
||||
In addition to the information on the flash bank itself, the
|
||||
device tree may optionally contain additional information
|
||||
describing partitions of the flash address space. This can be
|
||||
used on platforms which have strong conventions about which
|
||||
portions of the flash are used for what purposes, but which don't
|
||||
use an on-flash partition table such as RedBoot.
|
||||
|
||||
Each partition is represented as a sub-node of the flash device.
|
||||
Each node's name represents the name of the corresponding
|
||||
partition of the flash device.
|
||||
|
||||
Flash partitions
|
||||
- reg : The partition's offset and size within the flash bank.
|
||||
- label : (optional) The label / name for this flash partition.
|
||||
If omitted, the label is taken from the node name (excluding
|
||||
the unit address).
|
||||
- read-only : (optional) This parameter, if present, is a hint to
|
||||
Linux that this flash partition should only be mounted
|
||||
read-only. This is usually used for flash partitions
|
||||
containing early-boot firmware images or data which should not
|
||||
be clobbered.
|
||||
|
||||
Example:
|
||||
|
||||
flash@ff000000 {
|
||||
compatible = "amd,am29lv128ml", "cfi-flash";
|
||||
reg = <ff000000 01000000>;
|
||||
bank-width = <4>;
|
||||
device-width = <1>;
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
fs@0 {
|
||||
label = "fs";
|
||||
reg = <0 f80000>;
|
||||
};
|
||||
firmware@f80000 {
|
||||
label ="firmware";
|
||||
reg = <f80000 80000>;
|
||||
read-only;
|
||||
};
|
||||
};
|
||||
Loading…
Reference in New Issue