ARM: imx: move mx25 support to mach-imx

Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>

arch/arm/Makefile

@@ -154,7 +154,7 @@ machine-$(CONFIG_ARCH_MSM)		:= msm
 machine-$(CONFIG_ARCH_MV78XX0)		:= mv78xx0
 machine-$(CONFIG_ARCH_MX1)		:= imx
 machine-$(CONFIG_ARCH_MX2)		:= imx
-machine-$(CONFIG_ARCH_MX25)		:= mx25
+machine-$(CONFIG_ARCH_MX25)		:= imx
 machine-$(CONFIG_ARCH_MX3)		:= mx3
 machine-$(CONFIG_ARCH_MX5)		:= mx5
 machine-$(CONFIG_ARCH_MXC91231)		:= mxc91231

arch/arm/mach-imx/Kconfig

@@ -1,13 +1,34 @@
 config IMX_HAVE_DMA_V1
 	bool
 
-if ARCH_MX1
-
 config SOC_IMX1
+	bool
 	select CPU_ARM920T
 	select IMX_HAVE_DMA_V1
 	select IMX_HAVE_IOMUX_V1
+
+config SOC_IMX21
 	bool
+	select CPU_ARM926T
+	select ARCH_MXC_AUDMUX_V1
+	select IMX_HAVE_DMA_V1
+	select IMX_HAVE_IOMUX_V1
+
+config SOC_IMX25
+	bool
+	select CPU_ARM926T
+	select ARCH_MXC_IOMUX_V3
+	select HAVE_FB_IMX
+	select ARCH_MXC_AUDMUX_V2
+
+config SOC_IMX27
+	bool
+	select CPU_ARM926T
+	select ARCH_MXC_AUDMUX_V1
+	select IMX_HAVE_DMA_V1
+	select IMX_HAVE_IOMUX_V1
+
+if ARCH_MX1
 
 comment "MX1 platforms:"
 config MACH_MXLADS
@@ -31,20 +52,6 @@ endif
 
 if ARCH_MX2
 
-config SOC_IMX21
-	select CPU_ARM926T
-	select ARCH_MXC_AUDMUX_V1
-	select IMX_HAVE_DMA_V1
-	select IMX_HAVE_IOMUX_V1
-	bool
-
-config SOC_IMX27
-	select CPU_ARM926T
-	select ARCH_MXC_AUDMUX_V1
-	select IMX_HAVE_DMA_V1
-	select IMX_HAVE_IOMUX_V1
-	bool
-
 choice
 	prompt "CPUs:"
 	default MACH_MX21
@@ -81,6 +88,52 @@ config MACH_MX21ADS
 
 endif
 
+if ARCH_MX25
+
+comment "MX25 platforms:"
+
+config MACH_MX25_3DS
+	bool "Support MX25PDK (3DS) Platform"
+	select SOC_IMX25
+	select IMX_HAVE_PLATFORM_ESDHC
+	select IMX_HAVE_PLATFORM_IMX2_WDT
+	select IMX_HAVE_PLATFORM_IMXDI_RTC
+	select IMX_HAVE_PLATFORM_IMX_FB
+	select IMX_HAVE_PLATFORM_IMX_KEYPAD
+	select IMX_HAVE_PLATFORM_IMX_UART
+	select IMX_HAVE_PLATFORM_MXC_EHCI
+	select IMX_HAVE_PLATFORM_MXC_NAND
+
+config MACH_EUKREA_CPUIMX25
+	bool "Support Eukrea CPUIMX25 Platform"
+	select SOC_IMX25
+	select IMX_HAVE_PLATFORM_ESDHC
+	select IMX_HAVE_PLATFORM_FLEXCAN
+	select IMX_HAVE_PLATFORM_FSL_USB2_UDC
+	select IMX_HAVE_PLATFORM_IMXDI_RTC
+	select IMX_HAVE_PLATFORM_IMX_FB
+	select IMX_HAVE_PLATFORM_IMX_I2C
+	select IMX_HAVE_PLATFORM_IMX_UART
+	select IMX_HAVE_PLATFORM_MXC_EHCI
+	select IMX_HAVE_PLATFORM_MXC_NAND
+	select MXC_ULPI if USB_ULPI
+
+choice
+	prompt "Baseboard"
+	depends on MACH_EUKREA_CPUIMX25
+	default MACH_EUKREA_MBIMXSD25_BASEBOARD
+
+config MACH_EUKREA_MBIMXSD25_BASEBOARD
+	bool "Eukrea MBIMXSD development board"
+	select IMX_HAVE_PLATFORM_IMX_SSI
+	help
+	  This adds board specific devices that can be found on Eukrea's
+	  MBIMXSD evaluation board.
+
+endchoice
+
+endif
+
 if MACH_MX27
 
 comment "MX27 platforms:"

arch/arm/mach-imx/Makefile

@@ -9,6 +9,8 @@ obj-$(CONFIG_IMX_HAVE_DMA_V1) += dma-v1.o
 obj-$(CONFIG_ARCH_MX1) += clock-imx1.o mm-imx1.o
 obj-$(CONFIG_MACH_MX21) += clock-imx21.o mm-imx21.o
 
+obj-$(CONFIG_ARCH_MX25) += clock-imx25.o mm-imx25.o
+
 obj-$(CONFIG_MACH_MX27) += cpu-imx27.o pm-imx27.o
 obj-$(CONFIG_MACH_MX27) += clock-imx27.o mm-imx27.o
 
@@ -20,6 +22,10 @@ obj-$(CONFIG_MACH_SCB9328) += mach-scb9328.o
 
 obj-$(CONFIG_MACH_MX21ADS) += mach-mx21ads.o
 
+obj-$(CONFIG_MACH_MX25_3DS) += mach-mx25_3ds.o
+obj-$(CONFIG_MACH_EUKREA_CPUIMX25) += mach-eukrea_cpuimx25.o
+obj-$(CONFIG_MACH_EUKREA_MBIMXSD25_BASEBOARD) += eukrea_mbimxsd25-baseboard.o
+
 obj-$(CONFIG_MACH_MX27ADS) += mach-mx27ads.o
 obj-$(CONFIG_MACH_PCM038) += mach-pcm038.o
 obj-$(CONFIG_MACH_PCM970_BASEBOARD) += pcm970-baseboard.o

arch/arm/mach-imx/Makefile.boot

@@ -6,6 +6,10 @@ zreladdr-$(CONFIG_MACH_MX21)	:= 0xC0008000
 params_phys-$(CONFIG_MACH_MX21)	:= 0xC0000100
 initrd_phys-$(CONFIG_MACH_MX21)	:= 0xC0800000
 
+zreladdr-$(CONFIG_ARCH_MX25)	:= 0x80008000
+params_phys-$(CONFIG_ARCH_MX25)	:= 0x80000100
+initrd_phys-$(CONFIG_ARCH_MX25)	:= 0x80800000
+
 zreladdr-$(CONFIG_MACH_MX27)	:= 0xA0008000
 params_phys-$(CONFIG_MACH_MX27)	:= 0xA0000100
 initrd_phys-$(CONFIG_MACH_MX27)	:= 0xA0800000

arch/arm/mach-imx/mach-mx25_3ds.c

@@ -105,7 +105,7 @@ static struct pad_desc mx25pdk_pads[] = {
 };
 
 static const struct fec_platform_data mx25_fec_pdata __initconst = {
-        .phy    = PHY_INTERFACE_MODE_RMII,
+	.phy    = PHY_INTERFACE_MODE_RMII,
 };
 
 #define FEC_ENABLE_GPIO		35

arch/arm/mach-mx25/Kconfig

@@ -1,43 +0,0 @@
-if ARCH_MX25
-
-comment "MX25 platforms:"
-
-config MACH_MX25_3DS
-	bool "Support MX25PDK (3DS) Platform"
-	select IMX_HAVE_PLATFORM_ESDHC
-	select IMX_HAVE_PLATFORM_IMX2_WDT
-	select IMX_HAVE_PLATFORM_IMXDI_RTC
-	select IMX_HAVE_PLATFORM_IMX_FB
-	select IMX_HAVE_PLATFORM_IMX_KEYPAD
-	select IMX_HAVE_PLATFORM_IMX_UART
-	select IMX_HAVE_PLATFORM_MXC_EHCI
-	select IMX_HAVE_PLATFORM_MXC_NAND
-
-config MACH_EUKREA_CPUIMX25
-	bool "Support Eukrea CPUIMX25 Platform"
-	select IMX_HAVE_PLATFORM_ESDHC
-	select IMX_HAVE_PLATFORM_FLEXCAN
-	select IMX_HAVE_PLATFORM_FSL_USB2_UDC
-	select IMX_HAVE_PLATFORM_IMXDI_RTC
-	select IMX_HAVE_PLATFORM_IMX_FB
-	select IMX_HAVE_PLATFORM_IMX_I2C
-	select IMX_HAVE_PLATFORM_IMX_UART
-	select IMX_HAVE_PLATFORM_MXC_EHCI
-	select IMX_HAVE_PLATFORM_MXC_NAND
-	select MXC_ULPI if USB_ULPI
-
-choice
-	prompt "Baseboard"
-	depends on MACH_EUKREA_CPUIMX25
-	default MACH_EUKREA_MBIMXSD25_BASEBOARD
-
-config MACH_EUKREA_MBIMXSD25_BASEBOARD
-	bool "Eukrea MBIMXSD development board"
-	select IMX_HAVE_PLATFORM_IMX_SSI
-	help
-	  This adds board specific devices that can be found on Eukrea's
-	  MBIMXSD evaluation board.
-
-endchoice
-
-endif

arch/arm/mach-mx25/Makefile

@@ -1,5 +0,0 @@
-obj-y				:= mm.o
-obj-$(CONFIG_ARCH_MX25)		+= clock.o
-obj-$(CONFIG_MACH_MX25_3DS)	+= mach-mx25_3ds.o
-obj-$(CONFIG_MACH_EUKREA_CPUIMX25)		+= mach-cpuimx25.o
-obj-$(CONFIG_MACH_EUKREA_MBIMXSD25_BASEBOARD)	+= eukrea_mbimxsd-baseboard.o

arch/arm/mach-mx25/Makefile.boot

@@ -1,3 +0,0 @@
-   zreladdr-y	:= 0x80008000
-params_phys-y	:= 0x80000100
-initrd_phys-y	:= 0x80800000

arch/arm/plat-mxc/Kconfig

@@ -21,10 +21,6 @@ config ARCH_MX2
 
 config ARCH_MX25
 	bool "MX25-based"
-	select CPU_ARM926T
-	select ARCH_MXC_IOMUX_V3
-	select HAVE_FB_IMX
-	select ARCH_MXC_AUDMUX_V2
 	help
 	  This enables support for systems based on the Freescale i.MX25 family
 
@@ -51,7 +47,6 @@ endchoice
 
 source "arch/arm/mach-imx/Kconfig"
 source "arch/arm/mach-mx3/Kconfig"
-source "arch/arm/mach-mx25/Kconfig"
 source "arch/arm/mach-mxc91231/Kconfig"
 source "arch/arm/mach-mx5/Kconfig"