Merge branch 'omap-for-v4.12/dt-droid4-v2' into omap-for-v4.12/dt-v2
This commit is contained in:
Tony Lindgren
commit
da72e49364
|
|
@ -0,0 +1,194 @@
|
|||
/*
|
||||
* Common CPCAP configuration used on Motorola phones
|
||||
*
|
||||
* This program is free software; you can redistribute it and/or modify
|
||||
* it under the terms of the GNU General Public License version 2 as
|
||||
* published by the Free Software Foundation.
|
||||
*/
|
||||
|
||||
&mcspi1 {
|
||||
cpcap: pmic@0 {
|
||||
compatible = "motorola,cpcap", "st,6556002";
|
||||
reg = <0>; /* cs0 */
|
||||
interrupt-parent = <&gpio1>;
|
||||
interrupts = <7 IRQ_TYPE_EDGE_RISING>;
|
||||
interrupt-controller;
|
||||
#interrupt-cells = <2>;
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
spi-max-frequency = <3000000>;
|
||||
spi-cs-high;
|
||||
|
||||
cpcap_regulator: regulator {
|
||||
compatible = "motorola,mapphone-cpcap-regulator";
|
||||
|
||||
cpcap_regulators: regulators {
|
||||
};
|
||||
};
|
||||
|
||||
cpcap_rtc: rtc {
|
||||
compatible = "motorola,cpcap-rtc";
|
||||
|
||||
interrupt-parent = <&cpcap>;
|
||||
interrupts = <39 IRQ_TYPE_NONE>, <26 IRQ_TYPE_NONE>;
|
||||
};
|
||||
|
||||
power_button: button {
|
||||
compatible = "motorola,cpcap-pwrbutton";
|
||||
|
||||
interrupts = <23 IRQ_TYPE_NONE>;
|
||||
};
|
||||
|
||||
led_red: led-red {
|
||||
compatible = "motorola,cpcap-led-red";
|
||||
vdd-supply = <&sw5>;
|
||||
label = "status-led:red";
|
||||
};
|
||||
|
||||
led_green: led-green {
|
||||
compatible = "motorola,cpcap-led-green";
|
||||
vdd-supply = <&sw5>;
|
||||
label = "status-led:green";
|
||||
};
|
||||
|
||||
led_blue: led-blue {
|
||||
compatible = "motorola,cpcap-led-blue";
|
||||
vdd-supply = <&sw5>;
|
||||
label = "status-led:blue";
|
||||
};
|
||||
|
||||
led_adl: led-adl {
|
||||
compatible = "motorola,cpcap-led-adl";
|
||||
vdd-supply = <&sw5>;
|
||||
label = "button-backlight";
|
||||
};
|
||||
|
||||
led_cp: led-cp {
|
||||
compatible = "motorola,cpcap-led-cp";
|
||||
vdd-supply = <&sw5>;
|
||||
label = "shift-key-light";
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&cpcap_regulators {
|
||||
sw5: SW5 {
|
||||
regulator-min-microvolt = <5050000>;
|
||||
regulator-max-microvolt = <5050000>;
|
||||
regulator-enable-ramp-delay = <50000>;
|
||||
regulator-boot-on;
|
||||
};
|
||||
|
||||
vcam: VCAM {
|
||||
regulator-min-microvolt = <2900000>;
|
||||
regulator-max-microvolt = <2900000>;
|
||||
regulator-enable-ramp-delay = <1000>;
|
||||
};
|
||||
|
||||
/* Used by DSS */
|
||||
vcsi: VCSI {
|
||||
regulator-min-microvolt = <1800000>;
|
||||
regulator-max-microvolt = <1800000>;
|
||||
regulator-enable-ramp-delay = <1000>;
|
||||
regulator-boot-on;
|
||||
};
|
||||
|
||||
vdac: VDAC {
|
||||
regulator-min-microvolt = <1800000>;
|
||||
regulator-max-microvolt = <1800000>;
|
||||
regulator-enable-ramp-delay = <1000>;
|
||||
};
|
||||
|
||||
vdig: VDIG {
|
||||
regulator-min-microvolt = <1875000>;
|
||||
regulator-max-microvolt = <1875000>;
|
||||
regulator-enable-ramp-delay = <1000>;
|
||||
};
|
||||
|
||||
vfuse: VFUSE {
|
||||
regulator-min-microvolt = <1500000>;
|
||||
regulator-max-microvolt = <3150000>;
|
||||
regulator-enable-ramp-delay = <1000>;
|
||||
};
|
||||
|
||||
vhvio: VHVIO {
|
||||
regulator-min-microvolt = <2775000>;
|
||||
regulator-max-microvolt = <2775000>;
|
||||
regulator-enable-ramp-delay = <1000>;
|
||||
regulator-always-on;
|
||||
};
|
||||
|
||||
/* Used by eMMC at mmc2 */
|
||||
vsdio: VSDIO {
|
||||
regulator-min-microvolt = <2900000>;
|
||||
regulator-max-microvolt = <2900000>;
|
||||
regulator-enable-ramp-delay = <1000>;
|
||||
};
|
||||
|
||||
vpll: VPLL {
|
||||
regulator-min-microvolt = <1200000>;
|
||||
regulator-max-microvolt = <1800000>;
|
||||
regulator-enable-ramp-delay = <100>;
|
||||
};
|
||||
|
||||
vrf1: VRF1 {
|
||||
regulator-min-microvolt = <2775000>;
|
||||
regulator-max-microvolt = <2775000>;
|
||||
regulator-enable-ramp-delay = <1000>;
|
||||
};
|
||||
|
||||
vrf2: VRF2 {
|
||||
regulator-min-microvolt = <2775000>;
|
||||
regulator-max-microvolt = <2775000>;
|
||||
regulator-enable-ramp-delay = <1000>;
|
||||
};
|
||||
|
||||
vrfref: VRFREF {
|
||||
regulator-min-microvolt = <2500000>;
|
||||
regulator-max-microvolt = <2775000>;
|
||||
regulator-enable-ramp-delay = <100>;
|
||||
};
|
||||
|
||||
vwlan1: VWLAN1 {
|
||||
regulator-min-microvolt = <1800000>;
|
||||
regulator-max-microvolt = <1900000>;
|
||||
regulator-enable-ramp-delay = <1000>;
|
||||
};
|
||||
|
||||
/* Used by micro-SDIO at mmc1 */
|
||||
vwlan2: VWLAN2 {
|
||||
regulator-min-microvolt = <3000000>;
|
||||
regulator-max-microvolt = <3000000>;
|
||||
regulator-enable-ramp-delay = <1000>;
|
||||
};
|
||||
|
||||
vsim: VSIM {
|
||||
regulator-min-microvolt = <1800000>;
|
||||
regulator-max-microvolt = <2900000>;
|
||||
regulator-enable-ramp-delay = <1000>;
|
||||
};
|
||||
|
||||
vsimcard: VSIMCARD {
|
||||
regulator-min-microvolt = <1800000>;
|
||||
regulator-max-microvolt = <2900000>;
|
||||
regulator-enable-ramp-delay = <1000>;
|
||||
};
|
||||
|
||||
vvib: VVIB {
|
||||
regulator-min-microvolt = <1300000>;
|
||||
regulator-max-microvolt = <3000000>;
|
||||
regulator-enable-ramp-delay = <500>;
|
||||
};
|
||||
|
||||
vusb: VUSB {
|
||||
regulator-min-microvolt = <3300000>;
|
||||
regulator-max-microvolt = <3300000>;
|
||||
regulator-enable-ramp-delay = <1000>;
|
||||
};
|
||||
|
||||
vaudio: VAUDIO {
|
||||
regulator-min-microvolt = <2775000>;
|
||||
regulator-max-microvolt = <2775000>;
|
||||
regulator-enable-ramp-delay = <1000>;
|
||||
};
|
||||
};
|
||||
|
|
@ -5,7 +5,9 @@
|
|||
*/
|
||||
/dts-v1/;
|
||||
|
||||
#include <dt-bindings/input/input.h>
|
||||
#include "omap443x.dtsi"
|
||||
#include "motorola-cpcap-mapphone.dtsi"
|
||||
|
||||
/ {
|
||||
model = "Motorola Droid 4 XT894";
|
||||
|
|
@ -15,6 +17,11 @@
|
|||
stdout-path = &uart3;
|
||||
};
|
||||
|
||||
aliases {
|
||||
display0 = &lcd0;
|
||||
display1 = &hdmi0;
|
||||
};
|
||||
|
||||
/*
|
||||
* We seem to have only 1021 MB accessible, 1021 - 1022 is locked,
|
||||
* then 1023 - 1024 seems to contain mbm. For SRAM, see the notes
|
||||
|
|
@ -25,25 +32,62 @@
|
|||
reg = <0x80000000 0x3fd00000>; /* 1021 MB */
|
||||
};
|
||||
|
||||
/* CPCAP really supports 1650000 to 3400000 range */
|
||||
vmmc: regulator-mmc {
|
||||
/* Poweroff GPIO probably connected to CPCAP */
|
||||
gpio-poweroff {
|
||||
compatible = "gpio-poweroff";
|
||||
pinctrl-0 = <&poweroff_gpio>;
|
||||
pinctrl-names = "default";
|
||||
gpios = <&gpio2 18 GPIO_ACTIVE_LOW>; /* gpio50 */
|
||||
};
|
||||
|
||||
hdmi0: connector {
|
||||
compatible = "hdmi-connector";
|
||||
pinctrl-0 = <&hdmi_hpd_gpio>;
|
||||
pinctrl-names = "default";
|
||||
label = "hdmi";
|
||||
type = "d";
|
||||
|
||||
hpd-gpios = <&gpio2 31 GPIO_ACTIVE_HIGH>; /* gpio63 */
|
||||
|
||||
port {
|
||||
hdmi_connector_in: endpoint {
|
||||
remote-endpoint = <&hdmi_out>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
/*
|
||||
* HDMI 5V regulator probably sourced from battery. Let's keep
|
||||
* keep this as always enabled for HDMI to work until we've
|
||||
* figured what the encoder chip is.
|
||||
*/
|
||||
hdmi_regulator: regulator-hdmi {
|
||||
compatible = "regulator-fixed";
|
||||
regulator-name = "vmmc";
|
||||
regulator-min-microvolt = <3000000>;
|
||||
regulator-max-microvolt = <3000000>;
|
||||
regulator-name = "hdmi";
|
||||
regulator-min-microvolt = <5000000>;
|
||||
regulator-max-microvolt = <5000000>;
|
||||
gpio = <&gpio2 27 GPIO_ACTIVE_HIGH>; /* gpio59 */
|
||||
enable-active-high;
|
||||
regulator-always-on;
|
||||
};
|
||||
|
||||
/* CPCAP really supports 3000000 to 3100000 range */
|
||||
vemmc: regulator-emmc {
|
||||
compatible = "regulator-fixed";
|
||||
regulator-name = "vemmc";
|
||||
regulator-min-microvolt = <3000000>;
|
||||
regulator-max-microvolt = <3000000>;
|
||||
regulator-always-on;
|
||||
/* HS USB Host PHY on PORT 1 */
|
||||
hsusb1_phy: hsusb1_phy {
|
||||
compatible = "usb-nop-xceiv";
|
||||
};
|
||||
|
||||
/* CPCAP really supports 1650000 to 1950000 range */
|
||||
/* LCD regulator from sw5 source */
|
||||
lcd_regulator: regulator-lcd {
|
||||
compatible = "regulator-fixed";
|
||||
regulator-name = "lcd";
|
||||
regulator-min-microvolt = <5050000>;
|
||||
regulator-max-microvolt = <5050000>;
|
||||
gpio = <&gpio4 0 GPIO_ACTIVE_HIGH>; /* gpio96 */
|
||||
enable-active-high;
|
||||
vin-supply = <&sw5>;
|
||||
};
|
||||
|
||||
/* This is probably coming straight from the battery.. */
|
||||
wl12xx_vmmc: regulator-wl12xx {
|
||||
compatible = "regulator-fixed";
|
||||
regulator-name = "vwl1271";
|
||||
|
|
@ -53,6 +97,83 @@
|
|||
startup-delay-us = <70000>;
|
||||
enable-active-high;
|
||||
};
|
||||
|
||||
gpio_keys {
|
||||
compatible = "gpio-keys";
|
||||
|
||||
volume_down {
|
||||
label = "Volume Down";
|
||||
gpios = <&gpio5 26 GPIO_ACTIVE_LOW>; /* gpio154 */
|
||||
linux,code = <KEY_VOLUMEDOWN>;
|
||||
linux,can-disable;
|
||||
};
|
||||
|
||||
slider {
|
||||
label = "Keypad Slide";
|
||||
gpios = <&gpio4 26 GPIO_ACTIVE_HIGH>; /* gpio122 */
|
||||
linux,input-type = <EV_SW>;
|
||||
linux,code = <SW_KEYPAD_SLIDE>;
|
||||
linux,can-disable;
|
||||
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&dss {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&gpio6 {
|
||||
touchscreen_reset {
|
||||
gpio-hog;
|
||||
gpios = <13 0>;
|
||||
output-high;
|
||||
line-name = "touchscreen-reset";
|
||||
};
|
||||
};
|
||||
|
||||
&dsi1 {
|
||||
status = "okay";
|
||||
vdd-supply = <&vcsi>;
|
||||
|
||||
port {
|
||||
dsi1_out_ep: endpoint {
|
||||
remote-endpoint = <&lcd0_in>;
|
||||
lanes = <0 1 2 3 4 5>;
|
||||
};
|
||||
};
|
||||
|
||||
lcd0: display {
|
||||
compatible = "panel-dsi-cm";
|
||||
label = "lcd0";
|
||||
vddi-supply = <&lcd_regulator>;
|
||||
reset-gpios = <&gpio4 5 GPIO_ACTIVE_HIGH>; /* gpio101 */
|
||||
|
||||
panel-timing {
|
||||
clock-frequency = <0>; /* Calculated by dsi */
|
||||
|
||||
hback-porch = <2>;
|
||||
hactive = <540>;
|
||||
hfront-porch = <0>;
|
||||
hsync-len = <2>;
|
||||
|
||||
vback-porch = <1>;
|
||||
vactive = <960>;
|
||||
vfront-porch = <0>;
|
||||
vsync-len = <1>;
|
||||
|
||||
hsync-active = <0>;
|
||||
vsync-active = <0>;
|
||||
de-active = <1>;
|
||||
pixelclk-active = <1>;
|
||||
};
|
||||
|
||||
port {
|
||||
lcd0_in: endpoint {
|
||||
remote-endpoint = <&dsi1_out_ep>;
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
/* L3_2 interconnect is unused, SRAM, GPMC and L3_ICLK2 disabled */
|
||||
|
|
@ -60,14 +181,116 @@
|
|||
status = "disabled";
|
||||
};
|
||||
|
||||
&hdmi {
|
||||
status = "okay";
|
||||
pinctrl-0 = <&dss_hdmi_pins>;
|
||||
pinctrl-names = "default";
|
||||
vdda-supply = <&vdac>;
|
||||
|
||||
port {
|
||||
hdmi_out: endpoint {
|
||||
remote-endpoint = <&hdmi_connector_in>;
|
||||
lanes = <1 0 3 2 5 4 7 6>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&i2c1 {
|
||||
tmp105@48 {
|
||||
compatible = "ti,tmp105";
|
||||
reg = <0x48>;
|
||||
pinctrl-0 = <&tmp105_irq>;
|
||||
pinctrl-names = "default";
|
||||
/* kpd_row0.gpio_178 */
|
||||
interrupts-extended = <&gpio6 18 IRQ_TYPE_EDGE_FALLING
|
||||
&omap4_pmx_core 0x14e>;
|
||||
interrupt-names = "irq", "wakeup";
|
||||
wakeup-source;
|
||||
};
|
||||
};
|
||||
|
||||
&keypad {
|
||||
keypad,num-rows = <8>;
|
||||
keypad,num-columns = <8>;
|
||||
linux,keymap = <
|
||||
|
||||
/* Row 1 */
|
||||
MATRIX_KEY(0, 2, KEY_1)
|
||||
MATRIX_KEY(0, 6, KEY_2)
|
||||
MATRIX_KEY(2, 3, KEY_3)
|
||||
MATRIX_KEY(0, 7, KEY_4)
|
||||
MATRIX_KEY(0, 4, KEY_5)
|
||||
MATRIX_KEY(5, 5, KEY_6)
|
||||
MATRIX_KEY(0, 1, KEY_7)
|
||||
MATRIX_KEY(0, 5, KEY_8)
|
||||
MATRIX_KEY(0, 0, KEY_9)
|
||||
MATRIX_KEY(1, 6, KEY_0)
|
||||
|
||||
/* Row 2 */
|
||||
MATRIX_KEY(3, 4, KEY_APOSTROPHE)
|
||||
MATRIX_KEY(7, 6, KEY_Q)
|
||||
MATRIX_KEY(7, 7, KEY_W)
|
||||
MATRIX_KEY(7, 2, KEY_E)
|
||||
MATRIX_KEY(1, 0, KEY_R)
|
||||
MATRIX_KEY(4, 4, KEY_T)
|
||||
MATRIX_KEY(1, 2, KEY_Y)
|
||||
MATRIX_KEY(6, 7, KEY_U)
|
||||
MATRIX_KEY(2, 2, KEY_I)
|
||||
MATRIX_KEY(5, 6, KEY_O)
|
||||
MATRIX_KEY(3, 7, KEY_P)
|
||||
MATRIX_KEY(6, 5, KEY_BACKSPACE)
|
||||
|
||||
/* Row 3 */
|
||||
MATRIX_KEY(5, 4, KEY_TAB)
|
||||
MATRIX_KEY(5, 7, KEY_A)
|
||||
MATRIX_KEY(2, 7, KEY_S)
|
||||
MATRIX_KEY(7, 0, KEY_D)
|
||||
MATRIX_KEY(2, 6, KEY_F)
|
||||
MATRIX_KEY(6, 2, KEY_G)
|
||||
MATRIX_KEY(6, 6, KEY_H)
|
||||
MATRIX_KEY(1, 4, KEY_J)
|
||||
MATRIX_KEY(3, 1, KEY_K)
|
||||
MATRIX_KEY(2, 1, KEY_L)
|
||||
MATRIX_KEY(4, 6, KEY_ENTER)
|
||||
|
||||
/* Row 4 */
|
||||
MATRIX_KEY(3, 6, KEY_LEFTSHIFT) /* KEY_CAPSLOCK */
|
||||
MATRIX_KEY(6, 1, KEY_Z)
|
||||
MATRIX_KEY(7, 4, KEY_X)
|
||||
MATRIX_KEY(5, 1, KEY_C)
|
||||
MATRIX_KEY(1, 7, KEY_V)
|
||||
MATRIX_KEY(2, 4, KEY_B)
|
||||
MATRIX_KEY(4, 1, KEY_N)
|
||||
MATRIX_KEY(1, 1, KEY_M)
|
||||
MATRIX_KEY(3, 5, KEY_COMMA)
|
||||
MATRIX_KEY(5, 2, KEY_DOT)
|
||||
MATRIX_KEY(6, 3, KEY_UP)
|
||||
MATRIX_KEY(7, 3, KEY_OK)
|
||||
|
||||
/* Row 5 */
|
||||
MATRIX_KEY(2, 5, KEY_LEFTCTRL) /* KEY_LEFTSHIFT */
|
||||
MATRIX_KEY(4, 5, KEY_LEFTALT) /* SYM */
|
||||
MATRIX_KEY(6, 0, KEY_MINUS)
|
||||
MATRIX_KEY(4, 7, KEY_EQUAL)
|
||||
MATRIX_KEY(1, 5, KEY_SPACE)
|
||||
MATRIX_KEY(3, 2, KEY_SLASH)
|
||||
MATRIX_KEY(4, 3, KEY_LEFT)
|
||||
MATRIX_KEY(5, 3, KEY_DOWN)
|
||||
MATRIX_KEY(3, 3, KEY_RIGHT)
|
||||
|
||||
/* Side buttons, KEY_VOLUMEDOWN and KEY_PWER are on CPCAP? */
|
||||
MATRIX_KEY(5, 0, KEY_VOLUMEUP)
|
||||
>;
|
||||
};
|
||||
|
||||
&mmc1 {
|
||||
vmmc-supply = <&vmmc>;
|
||||
vmmc-supply = <&vwlan2>;
|
||||
bus-width = <4>;
|
||||
cd-gpios = <&gpio4 10 GPIO_ACTIVE_LOW>; /* gpio106 */
|
||||
cd-gpios = <&gpio6 16 GPIO_ACTIVE_LOW>; /* gpio176 */
|
||||
};
|
||||
|
||||
&mmc2 {
|
||||
vmmc-supply = <&vemmc>;
|
||||
vmmc-supply = <&vsdio>;
|
||||
bus-width = <8>;
|
||||
non-removable;
|
||||
};
|
||||
|
|
@ -93,12 +316,83 @@
|
|||
};
|
||||
};
|
||||
|
||||
&i2c1 {
|
||||
lm3532@38 {
|
||||
compatible = "ti,lm3532";
|
||||
reg = <0x38>;
|
||||
|
||||
enable-gpios = <&gpio6 12 GPIO_ACTIVE_HIGH>;
|
||||
|
||||
backlight {
|
||||
compatible = "ti,lm3532-backlight";
|
||||
|
||||
lcd {
|
||||
led-sources = <0 1 2>;
|
||||
ramp-up-msec = <1>;
|
||||
ramp-down-msec = <0>;
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
/*
|
||||
* REVISIT: Add gpio173 reset pin handling to the driver, see gpio-hog above.
|
||||
* If the GPIO reset is used, we probably need to have /lib/firmware/maxtouch.fw
|
||||
* available. See "mxt-app" and "droid4-touchscreen-firmware" tools for more
|
||||
* information.
|
||||
*/
|
||||
&i2c2 {
|
||||
tsp@4a {
|
||||
compatible = "atmel,maxtouch";
|
||||
reg = <0x4a>;
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&touchscreen_pins>;
|
||||
|
||||
/* gpio_183 with sys_nirq2 pad as wakeup */
|
||||
interrupts-extended = <&gpio6 23 IRQ_TYPE_EDGE_FALLING
|
||||
&omap4_pmx_core 0x160>;
|
||||
interrupt-names = "irq", "wakeup";
|
||||
wakeup-source;
|
||||
};
|
||||
};
|
||||
|
||||
/* L3_2 interconnect is unused, SRAM, GPMC and L3_ICLK2 disabled */
|
||||
&ocmcram {
|
||||
status = "disabled";
|
||||
};
|
||||
|
||||
&omap4_pmx_core {
|
||||
|
||||
/* hdmi_hpd.gpio_63 */
|
||||
hdmi_hpd_gpio: pinmux_hdmi_hpd_pins {
|
||||
pinctrl-single,pins = <
|
||||
OMAP4_IOPAD(0x098, PIN_INPUT | MUX_MODE3)
|
||||
>;
|
||||
};
|
||||
|
||||
/* hdmi_cec.hdmi_cec, hdmi_scl.hdmi_scl, hdmi_sda.hdmi_sda */
|
||||
dss_hdmi_pins: pinmux_dss_hdmi_pins {
|
||||
pinctrl-single,pins = <
|
||||
OMAP4_IOPAD(0x09a, PIN_INPUT_PULLUP | MUX_MODE0)
|
||||
OMAP4_IOPAD(0x09c, PIN_INPUT | MUX_MODE0)
|
||||
OMAP4_IOPAD(0x09e, PIN_INPUT | MUX_MODE0)
|
||||
>;
|
||||
};
|
||||
|
||||
/* gpmc_ncs0.gpio_50 */
|
||||
poweroff_gpio: pinmux_poweroff_pins {
|
||||
pinctrl-single,pins = <
|
||||
OMAP4_IOPAD(0x074, PIN_OUTPUT_PULLUP | MUX_MODE3)
|
||||
>;
|
||||
};
|
||||
|
||||
/* kpd_row0.gpio_178 */
|
||||
tmp105_irq: pinmux_tmp105_irq {
|
||||
pinctrl-single,pins = <
|
||||
OMAP4_IOPAD(0x18e, PIN_INPUT_PULLUP | MUX_MODE3)
|
||||
>;
|
||||
};
|
||||
|
||||
usb_gpio_mux_sel1: pinmux_usb_gpio_mux_sel1_pins {
|
||||
/* gpio_60 */
|
||||
pinctrl-single,pins = <
|
||||
|
|
@ -106,6 +400,12 @@
|
|||
>;
|
||||
};
|
||||
|
||||
touchscreen_pins: pinmux_touchscreen_pins {
|
||||
pinctrl-single,pins = <
|
||||
OMAP4_IOPAD(0x1a0, PIN_INPUT_PULLUP | MUX_MODE3)
|
||||
>;
|
||||
};
|
||||
|
||||
usb_ulpi_pins: pinmux_usb_ulpi_pins {
|
||||
pinctrl-single,pins = <
|
||||
OMAP4_IOPAD(0x196, MUX_MODE7)
|
||||
|
|
@ -180,9 +480,49 @@
|
|||
&omap4_pmx_core 0x17c>;
|
||||
};
|
||||
|
||||
&usbhsehci {
|
||||
phys = <&hsusb1_phy>;
|
||||
};
|
||||
|
||||
&usbhshost {
|
||||
port1-mode = "ohci-phy-4pin-dpdm";
|
||||
port2-mode = "ehci-tll";
|
||||
};
|
||||
|
||||
/* Internal UTMI+ PHY used for OTG, CPCAP ULPI PHY for detection and charger */
|
||||
&usb_otg_hs {
|
||||
interface-type = <1>;
|
||||
mode = <3>;
|
||||
power = <50>;
|
||||
};
|
||||
|
||||
&i2c4 {
|
||||
ak8975: magnetometer@c {
|
||||
compatible = "asahi-kasei,ak8975";
|
||||
reg = <0x0c>;
|
||||
|
||||
vdd-supply = <&vhvio>;
|
||||
|
||||
interrupt-parent = <&gpio6>;
|
||||
interrupts = <15 IRQ_TYPE_EDGE_RISING>; /* gpio175 */
|
||||
|
||||
rotation-matrix = "-1", "0", "0",
|
||||
"0", "1", "0",
|
||||
"0", "0", "-1";
|
||||
|
||||
};
|
||||
|
||||
lis3dh: accelerometer@18 {
|
||||
compatible = "st,lis3dh-accel";
|
||||
reg = <0x18>;
|
||||
|
||||
vdd-supply = <&vhvio>;
|
||||
|
||||
interrupt-parent = <&gpio2>;
|
||||
interrupts = <2 IRQ_TYPE_EDGE_BOTH>; /* gpio34 */
|
||||
|
||||
rotation-matrix = "0", "-1", "0",
|
||||
"1", "0", "0",
|
||||
"0", "0", "1";
|
||||
};
|
||||
};
|
||||
|
|
|
|||
Loading…
Reference in New Issue