From d3a8f13b11e34b377e5fbc544c6780ba83e0346a Mon Sep 17 00:00:00 2001 From: Yaniv Rosner Date: Thu, 13 Sep 2012 02:56:20 +0000 Subject: [PATCH] bnx2x: Link Flap Avoidance Various flows in the bnx2x driver cause a link-flap - if the link is up, it would be toggled down (after a mac/phy reset) and then taken back up. In many of these cases, there is no need to do cause such a flap, as the associated flows should not actually affect the link. This patch adds the 'Link Flap Avoidance' mechanism, which allows the driver to better determine if a given flow requires a link change, and thus minimize the number of link flaps caused by the driver. Signed-off-by: Yaniv Rosner Signed-off-by: Yuval Mintz Signed-off-by: Eilon Greenstein Signed-off-by: David S. Miller --- .../net/ethernet/broadcom/bnx2x/bnx2x_hsi.h | 48 ++ .../net/ethernet/broadcom/bnx2x/bnx2x_link.c | 435 ++++++++++++++++-- .../net/ethernet/broadcom/bnx2x/bnx2x_link.h | 2 + 3 files changed, 437 insertions(+), 48 deletions(-) diff --git a/drivers/net/ethernet/broadcom/bnx2x/bnx2x_hsi.h b/drivers/net/ethernet/broadcom/bnx2x/bnx2x_hsi.h index 76b6e65790f8..df1400664ab3 100644 --- a/drivers/net/ethernet/broadcom/bnx2x/bnx2x_hsi.h +++ b/drivers/net/ethernet/broadcom/bnx2x/bnx2x_hsi.h @@ -1909,6 +1909,54 @@ struct lldp_local_mib { }; /***END OF DCBX STRUCTURES DECLARATIONS***/ +/***********************************************************/ +/* Elink section */ +/***********************************************************/ +#define SHMEM_LINK_CONFIG_SIZE 2 +struct shmem_lfa { + u32 req_duplex; + #define REQ_DUPLEX_PHY0_MASK 0x0000ffff + #define REQ_DUPLEX_PHY0_SHIFT 0 + #define REQ_DUPLEX_PHY1_MASK 0xffff0000 + #define REQ_DUPLEX_PHY1_SHIFT 16 + u32 req_flow_ctrl; + #define REQ_FLOW_CTRL_PHY0_MASK 0x0000ffff + #define REQ_FLOW_CTRL_PHY0_SHIFT 0 + #define REQ_FLOW_CTRL_PHY1_MASK 0xffff0000 + #define REQ_FLOW_CTRL_PHY1_SHIFT 16 + u32 req_line_speed; /* Also determine AutoNeg */ + #define REQ_LINE_SPD_PHY0_MASK 0x0000ffff + #define REQ_LINE_SPD_PHY0_SHIFT 0 + #define REQ_LINE_SPD_PHY1_MASK 0xffff0000 + #define REQ_LINE_SPD_PHY1_SHIFT 16 + u32 speed_cap_mask[SHMEM_LINK_CONFIG_SIZE]; + u32 additional_config; + #define REQ_FC_AUTO_ADV_MASK 0x0000ffff + #define REQ_FC_AUTO_ADV0_SHIFT 0 + #define NO_LFA_DUE_TO_DCC_MASK 0x00010000 + u32 lfa_sts; + #define LFA_LINK_FLAP_REASON_OFFSET 0 + #define LFA_LINK_FLAP_REASON_MASK 0x000000ff + #define LFA_LINK_DOWN 0x1 + #define LFA_LOOPBACK_ENABLED 0x2 + #define LFA_DUPLEX_MISMATCH 0x3 + #define LFA_MFW_IS_TOO_OLD 0x4 + #define LFA_LINK_SPEED_MISMATCH 0x5 + #define LFA_FLOW_CTRL_MISMATCH 0x6 + #define LFA_SPEED_CAP_MISMATCH 0x7 + #define LFA_DCC_LFA_DISABLED 0x8 + #define LFA_EEE_MISMATCH 0x9 + + #define LINK_FLAP_AVOIDANCE_COUNT_OFFSET 8 + #define LINK_FLAP_AVOIDANCE_COUNT_MASK 0x0000ff00 + + #define LINK_FLAP_COUNT_OFFSET 16 + #define LINK_FLAP_COUNT_MASK 0x00ff0000 + + #define LFA_FLAGS_MASK 0xff000000 + #define SHMEM_LFA_DONT_CLEAR_STAT (1<<24) +}; + struct ncsi_oem_fcoe_features { u32 fcoe_features1; #define FCOE_FEATURES1_IOS_PER_CONNECTION_MASK 0x0000FFFF diff --git a/drivers/net/ethernet/broadcom/bnx2x/bnx2x_link.c b/drivers/net/ethernet/broadcom/bnx2x/bnx2x_link.c index f7e236e68f17..4eca0f863073 100644 --- a/drivers/net/ethernet/broadcom/bnx2x/bnx2x_link.c +++ b/drivers/net/ethernet/broadcom/bnx2x/bnx2x_link.c @@ -321,6 +321,127 @@ static u32 bnx2x_bits_dis(struct bnx2x *bp, u32 reg, u32 bits) return val; } +/* + * bnx2x_check_lfa - This function checks if link reinitialization is required, + * or link flap can be avoided. + * + * @params: link parameters + * Returns 0 if Link Flap Avoidance conditions are met otherwise, the failed + * condition code. + */ +static int bnx2x_check_lfa(struct link_params *params) +{ + u32 link_status, cfg_idx, lfa_mask, cfg_size; + u32 cur_speed_cap_mask, cur_req_fc_auto_adv, additional_config; + u32 saved_val, req_val, eee_status; + struct bnx2x *bp = params->bp; + + additional_config = + REG_RD(bp, params->lfa_base + + offsetof(struct shmem_lfa, additional_config)); + + /* NOTE: must be first condition checked - + * to verify DCC bit is cleared in any case! + */ + if (additional_config & NO_LFA_DUE_TO_DCC_MASK) { + DP(NETIF_MSG_LINK, "No LFA due to DCC flap after clp exit\n"); + REG_WR(bp, params->lfa_base + + offsetof(struct shmem_lfa, additional_config), + additional_config & ~NO_LFA_DUE_TO_DCC_MASK); + return LFA_DCC_LFA_DISABLED; + } + + /* Verify that link is up */ + link_status = REG_RD(bp, params->shmem_base + + offsetof(struct shmem_region, + port_mb[params->port].link_status)); + if (!(link_status & LINK_STATUS_LINK_UP)) + return LFA_LINK_DOWN; + + /* Verify that loopback mode is not set */ + if (params->loopback_mode) + return LFA_LOOPBACK_ENABLED; + + /* Verify that MFW supports LFA */ + if (!params->lfa_base) + return LFA_MFW_IS_TOO_OLD; + + if (params->num_phys == 3) { + cfg_size = 2; + lfa_mask = 0xffffffff; + } else { + cfg_size = 1; + lfa_mask = 0xffff; + } + + /* Compare Duplex */ + saved_val = REG_RD(bp, params->lfa_base + + offsetof(struct shmem_lfa, req_duplex)); + req_val = params->req_duplex[0] | (params->req_duplex[1] << 16); + if ((saved_val & lfa_mask) != (req_val & lfa_mask)) { + DP(NETIF_MSG_LINK, "Duplex mismatch %x vs. %x\n", + (saved_val & lfa_mask), (req_val & lfa_mask)); + return LFA_DUPLEX_MISMATCH; + } + /* Compare Flow Control */ + saved_val = REG_RD(bp, params->lfa_base + + offsetof(struct shmem_lfa, req_flow_ctrl)); + req_val = params->req_flow_ctrl[0] | (params->req_flow_ctrl[1] << 16); + if ((saved_val & lfa_mask) != (req_val & lfa_mask)) { + DP(NETIF_MSG_LINK, "Flow control mismatch %x vs. %x\n", + (saved_val & lfa_mask), (req_val & lfa_mask)); + return LFA_FLOW_CTRL_MISMATCH; + } + /* Compare Link Speed */ + saved_val = REG_RD(bp, params->lfa_base + + offsetof(struct shmem_lfa, req_line_speed)); + req_val = params->req_line_speed[0] | (params->req_line_speed[1] << 16); + if ((saved_val & lfa_mask) != (req_val & lfa_mask)) { + DP(NETIF_MSG_LINK, "Link speed mismatch %x vs. %x\n", + (saved_val & lfa_mask), (req_val & lfa_mask)); + return LFA_LINK_SPEED_MISMATCH; + } + + for (cfg_idx = 0; cfg_idx < cfg_size; cfg_idx++) { + cur_speed_cap_mask = REG_RD(bp, params->lfa_base + + offsetof(struct shmem_lfa, + speed_cap_mask[cfg_idx])); + + if (cur_speed_cap_mask != params->speed_cap_mask[cfg_idx]) { + DP(NETIF_MSG_LINK, "Speed Cap mismatch %x vs. %x\n", + cur_speed_cap_mask, + params->speed_cap_mask[cfg_idx]); + return LFA_SPEED_CAP_MISMATCH; + } + } + + cur_req_fc_auto_adv = + REG_RD(bp, params->lfa_base + + offsetof(struct shmem_lfa, additional_config)) & + REQ_FC_AUTO_ADV_MASK; + + if ((u16)cur_req_fc_auto_adv != params->req_fc_auto_adv) { + DP(NETIF_MSG_LINK, "Flow Ctrl AN mismatch %x vs. %x\n", + cur_req_fc_auto_adv, params->req_fc_auto_adv); + return LFA_FLOW_CTRL_MISMATCH; + } + + eee_status = REG_RD(bp, params->shmem2_base + + offsetof(struct shmem2_region, + eee_status[params->port])); + + if (((eee_status & SHMEM_EEE_LPI_REQUESTED_BIT) ^ + (params->eee_mode & EEE_MODE_ENABLE_LPI)) || + ((eee_status & SHMEM_EEE_REQUESTED_BIT) ^ + (params->eee_mode & EEE_MODE_ADV_LPI))) { + DP(NETIF_MSG_LINK, "EEE mismatch %x vs. %x\n", params->eee_mode, + eee_status); + return LFA_EEE_MISMATCH; + } + + /* LFA conditions are met */ + return 0; +} /******************************************************************/ /* EPIO/GPIO section */ /******************************************************************/ @@ -1519,16 +1640,23 @@ static void bnx2x_set_xumac_nig(struct link_params *params, NIG_REG_P0_MAC_PAUSE_OUT_EN, tx_pause_en); } -static void bnx2x_umac_disable(struct link_params *params) +static void bnx2x_set_umac_rxtx(struct link_params *params, u8 en) { u32 umac_base = params->port ? GRCBASE_UMAC1 : GRCBASE_UMAC0; + u32 val; struct bnx2x *bp = params->bp; if (!(REG_RD(bp, MISC_REG_RESET_REG_2) & (MISC_REGISTERS_RESET_REG_2_UMAC0 << params->port))) return; - + val = REG_RD(bp, umac_base + UMAC_REG_COMMAND_CONFIG); + if (en) + val |= (UMAC_COMMAND_CONFIG_REG_TX_ENA | + UMAC_COMMAND_CONFIG_REG_RX_ENA); + else + val &= ~(UMAC_COMMAND_CONFIG_REG_TX_ENA | + UMAC_COMMAND_CONFIG_REG_RX_ENA); /* Disable RX and TX */ - REG_WR(bp, umac_base + UMAC_REG_COMMAND_CONFIG, 0); + REG_WR(bp, umac_base + UMAC_REG_COMMAND_CONFIG, val); } static void bnx2x_umac_enable(struct link_params *params, @@ -1689,11 +1817,12 @@ static void bnx2x_xmac_init(struct link_params *params, u32 max_speed) } -static void bnx2x_xmac_disable(struct link_params *params) +static void bnx2x_set_xmac_rxtx(struct link_params *params, u8 en) { u8 port = params->port; struct bnx2x *bp = params->bp; u32 pfc_ctrl, xmac_base = (port) ? GRCBASE_XMAC1 : GRCBASE_XMAC0; + u32 val; if (REG_RD(bp, MISC_REG_RESET_REG_2) & MISC_REGISTERS_RESET_REG_2_XMAC) { @@ -1707,7 +1836,12 @@ static void bnx2x_xmac_disable(struct link_params *params) REG_WR(bp, xmac_base + XMAC_REG_PFC_CTRL_HI, (pfc_ctrl | (1<<1))); DP(NETIF_MSG_LINK, "Disable XMAC on port %x\n", port); - REG_WR(bp, xmac_base + XMAC_REG_CTRL, 0); + val = REG_RD(bp, xmac_base + XMAC_REG_CTRL); + if (en) + val |= (XMAC_CTRL_REG_TX_EN | XMAC_CTRL_REG_RX_EN); + else + val &= ~(XMAC_CTRL_REG_TX_EN | XMAC_CTRL_REG_RX_EN); + REG_WR(bp, xmac_base + XMAC_REG_CTRL, val); } } @@ -2738,16 +2872,18 @@ static int bnx2x_bmac2_enable(struct link_params *params, static int bnx2x_bmac_enable(struct link_params *params, struct link_vars *vars, - u8 is_lb) + u8 is_lb, u8 reset_bmac) { int rc = 0; u8 port = params->port; struct bnx2x *bp = params->bp; u32 val; /* Reset and unreset the BigMac */ - REG_WR(bp, GRCBASE_MISC + MISC_REGISTERS_RESET_REG_2_CLEAR, - (MISC_REGISTERS_RESET_REG_2_RST_BMAC0 << port)); - usleep_range(1000, 2000); + if (reset_bmac) { + REG_WR(bp, GRCBASE_MISC + MISC_REGISTERS_RESET_REG_2_CLEAR, + (MISC_REGISTERS_RESET_REG_2_RST_BMAC0 << port)); + usleep_range(1000, 2000); + } REG_WR(bp, GRCBASE_MISC + MISC_REGISTERS_RESET_REG_2_SET, (MISC_REGISTERS_RESET_REG_2_RST_BMAC0 << port)); @@ -2779,37 +2915,28 @@ static int bnx2x_bmac_enable(struct link_params *params, return rc; } -static void bnx2x_bmac_rx_disable(struct bnx2x *bp, u8 port) +static void bnx2x_set_bmac_rx(struct bnx2x *bp, u32 chip_id, u8 port, u8 en) { u32 bmac_addr = port ? NIG_REG_INGRESS_BMAC1_MEM : NIG_REG_INGRESS_BMAC0_MEM; u32 wb_data[2]; u32 nig_bmac_enable = REG_RD(bp, NIG_REG_BMAC0_REGS_OUT_EN + port*4); + if (CHIP_IS_E2(bp)) + bmac_addr += BIGMAC2_REGISTER_BMAC_CONTROL; + else + bmac_addr += BIGMAC_REGISTER_BMAC_CONTROL; /* Only if the bmac is out of reset */ if (REG_RD(bp, MISC_REG_RESET_REG_2) & (MISC_REGISTERS_RESET_REG_2_RST_BMAC0 << port) && nig_bmac_enable) { - - if (CHIP_IS_E2(bp)) { - /* Clear Rx Enable bit in BMAC_CONTROL register */ - REG_RD_DMAE(bp, bmac_addr + - BIGMAC2_REGISTER_BMAC_CONTROL, - wb_data, 2); + /* Clear Rx Enable bit in BMAC_CONTROL register */ + REG_RD_DMAE(bp, bmac_addr, wb_data, 2); + if (en) + wb_data[0] |= BMAC_CONTROL_RX_ENABLE; + else wb_data[0] &= ~BMAC_CONTROL_RX_ENABLE; - REG_WR_DMAE(bp, bmac_addr + - BIGMAC2_REGISTER_BMAC_CONTROL, - wb_data, 2); - } else { - /* Clear Rx Enable bit in BMAC_CONTROL register */ - REG_RD_DMAE(bp, bmac_addr + - BIGMAC_REGISTER_BMAC_CONTROL, - wb_data, 2); - wb_data[0] &= ~BMAC_CONTROL_RX_ENABLE; - REG_WR_DMAE(bp, bmac_addr + - BIGMAC_REGISTER_BMAC_CONTROL, - wb_data, 2); - } + REG_WR_DMAE(bp, bmac_addr, wb_data, 2); usleep_range(1000, 2000); } } @@ -4568,7 +4695,7 @@ static void bnx2x_warpcore_config_init(struct bnx2x_phy *phy, "serdes_net_if = 0x%x\n", vars->line_speed, serdes_net_if); bnx2x_set_aer_mmd(params, phy); - + bnx2x_warpcore_reset_lane(bp, phy, 1); vars->phy_flags |= PHY_XGXS_FLAG; if ((serdes_net_if == PORT_HW_CFG_NET_SERDES_IF_SGMII) || (phy->req_line_speed && @@ -6691,12 +6818,9 @@ static int bnx2x_update_link_down(struct link_params *params, usleep_range(10000, 20000); /* Reset BigMac/Xmac */ if (CHIP_IS_E1x(bp) || - CHIP_IS_E2(bp)) { - bnx2x_bmac_rx_disable(bp, params->port); - REG_WR(bp, GRCBASE_MISC + - MISC_REGISTERS_RESET_REG_2_CLEAR, - (MISC_REGISTERS_RESET_REG_2_RST_BMAC0 << port)); - } + CHIP_IS_E2(bp)) + bnx2x_set_bmac_rx(bp, params->chip_id, params->port, 0); + if (CHIP_IS_E3(bp)) { /* Prevent LPI Generation by chip */ REG_WR(bp, MISC_REG_CPMU_LP_FW_ENABLE_P0 + (params->port << 2), @@ -6707,8 +6831,8 @@ static int bnx2x_update_link_down(struct link_params *params, SHMEM_EEE_ACTIVE_BIT); bnx2x_update_mng_eee(params, vars->eee_status); - bnx2x_xmac_disable(params); - bnx2x_umac_disable(params); + bnx2x_set_xmac_rxtx(params, 0); + bnx2x_set_umac_rxtx(params, 0); } return 0; @@ -6760,7 +6884,7 @@ static int bnx2x_update_link_up(struct link_params *params, if ((CHIP_IS_E1x(bp) || CHIP_IS_E2(bp))) { if (link_10g) { - if (bnx2x_bmac_enable(params, vars, 0) == + if (bnx2x_bmac_enable(params, vars, 0, 1) == -ESRCH) { DP(NETIF_MSG_LINK, "Found errors on BMAC\n"); vars->link_up = 0; @@ -12257,7 +12381,7 @@ void bnx2x_init_bmac_loopback(struct link_params *params, bnx2x_xgxs_deassert(params); /* set bmac loopback */ - bnx2x_bmac_enable(params, vars, 1); + bnx2x_bmac_enable(params, vars, 1, 1); REG_WR(bp, NIG_REG_EGRESS_DRAIN0_MODE + params->port*4, 0); } @@ -12349,7 +12473,7 @@ void bnx2x_init_xgxs_loopback(struct link_params *params, if (USES_WARPCORE(bp)) bnx2x_xmac_enable(params, vars, 0); else - bnx2x_bmac_enable(params, vars, 0); + bnx2x_bmac_enable(params, vars, 0, 1); } if (params->loopback_mode == LOOPBACK_XGXS) { @@ -12374,8 +12498,161 @@ void bnx2x_init_xgxs_loopback(struct link_params *params, bnx2x_set_led(params, vars, LED_MODE_OPER, vars->line_speed); } +static void bnx2x_set_rx_filter(struct link_params *params, u8 en) +{ + struct bnx2x *bp = params->bp; + u8 val = en * 0x1F; + + /* Open the gate between the NIG to the BRB */ + if (!CHIP_IS_E1x(bp)) + val |= en * 0x20; + REG_WR(bp, NIG_REG_LLH0_BRB1_DRV_MASK + params->port*4, val); + + if (!CHIP_IS_E1(bp)) { + REG_WR(bp, NIG_REG_LLH0_BRB1_DRV_MASK_MF + params->port*4, + en*0x3); + } + + REG_WR(bp, (params->port ? NIG_REG_LLH1_BRB1_NOT_MCP : + NIG_REG_LLH0_BRB1_NOT_MCP), en); +} +static int bnx2x_avoid_link_flap(struct link_params *params, + struct link_vars *vars) +{ + u32 phy_idx; + u32 dont_clear_stat, lfa_sts; + struct bnx2x *bp = params->bp; + + /* Sync the link parameters */ + bnx2x_link_status_update(params, vars); + + /* + * The module verification was already done by previous link owner, + * so this call is meant only to get warning message + */ + + for (phy_idx = INT_PHY; phy_idx < params->num_phys; phy_idx++) { + struct bnx2x_phy *phy = ¶ms->phy[phy_idx]; + if (phy->phy_specific_func) { + DP(NETIF_MSG_LINK, "Calling PHY specific func\n"); + phy->phy_specific_func(phy, params, PHY_INIT); + } + if ((phy->media_type == ETH_PHY_SFPP_10G_FIBER) || + (phy->media_type == ETH_PHY_SFP_1G_FIBER) || + (phy->media_type == ETH_PHY_DA_TWINAX)) + bnx2x_verify_sfp_module(phy, params); + } + lfa_sts = REG_RD(bp, params->lfa_base + + offsetof(struct shmem_lfa, + lfa_sts)); + + dont_clear_stat = lfa_sts & SHMEM_LFA_DONT_CLEAR_STAT; + + /* Re-enable the NIG/MAC */ + if (CHIP_IS_E3(bp)) { + if (!dont_clear_stat) { + REG_WR(bp, GRCBASE_MISC + + MISC_REGISTERS_RESET_REG_2_CLEAR, + (MISC_REGISTERS_RESET_REG_2_MSTAT0 << + params->port)); + REG_WR(bp, GRCBASE_MISC + + MISC_REGISTERS_RESET_REG_2_SET, + (MISC_REGISTERS_RESET_REG_2_MSTAT0 << + params->port)); + } + if (vars->line_speed < SPEED_10000) + bnx2x_umac_enable(params, vars, 0); + else + bnx2x_xmac_enable(params, vars, 0); + } else { + if (vars->line_speed < SPEED_10000) + bnx2x_emac_enable(params, vars, 0); + else + bnx2x_bmac_enable(params, vars, 0, !dont_clear_stat); + } + + /* Increment LFA count */ + lfa_sts = ((lfa_sts & ~LINK_FLAP_AVOIDANCE_COUNT_MASK) | + (((((lfa_sts & LINK_FLAP_AVOIDANCE_COUNT_MASK) >> + LINK_FLAP_AVOIDANCE_COUNT_OFFSET) + 1) & 0xff) + << LINK_FLAP_AVOIDANCE_COUNT_OFFSET)); + /* Clear link flap reason */ + lfa_sts &= ~LFA_LINK_FLAP_REASON_MASK; + + REG_WR(bp, params->lfa_base + + offsetof(struct shmem_lfa, lfa_sts), lfa_sts); + + /* Disable NIG DRAIN */ + REG_WR(bp, NIG_REG_EGRESS_DRAIN0_MODE + params->port*4, 0); + + /* Enable interrupts */ + bnx2x_link_int_enable(params); + return 0; +} + +static void bnx2x_cannot_avoid_link_flap(struct link_params *params, + struct link_vars *vars, + int lfa_status) +{ + u32 lfa_sts, cfg_idx, tmp_val; + struct bnx2x *bp = params->bp; + + bnx2x_link_reset(params, vars, 1); + + if (!params->lfa_base) + return; + /* Store the new link parameters */ + REG_WR(bp, params->lfa_base + + offsetof(struct shmem_lfa, req_duplex), + params->req_duplex[0] | (params->req_duplex[1] << 16)); + + REG_WR(bp, params->lfa_base + + offsetof(struct shmem_lfa, req_flow_ctrl), + params->req_flow_ctrl[0] | (params->req_flow_ctrl[1] << 16)); + + REG_WR(bp, params->lfa_base + + offsetof(struct shmem_lfa, req_line_speed), + params->req_line_speed[0] | (params->req_line_speed[1] << 16)); + + for (cfg_idx = 0; cfg_idx < SHMEM_LINK_CONFIG_SIZE; cfg_idx++) { + REG_WR(bp, params->lfa_base + + offsetof(struct shmem_lfa, + speed_cap_mask[cfg_idx]), + params->speed_cap_mask[cfg_idx]); + } + + tmp_val = REG_RD(bp, params->lfa_base + + offsetof(struct shmem_lfa, additional_config)); + tmp_val &= ~REQ_FC_AUTO_ADV_MASK; + tmp_val |= params->req_fc_auto_adv; + + REG_WR(bp, params->lfa_base + + offsetof(struct shmem_lfa, additional_config), tmp_val); + + lfa_sts = REG_RD(bp, params->lfa_base + + offsetof(struct shmem_lfa, lfa_sts)); + + /* Clear the "Don't Clear Statistics" bit, and set reason */ + lfa_sts &= ~SHMEM_LFA_DONT_CLEAR_STAT; + + /* Set link flap reason */ + lfa_sts &= ~LFA_LINK_FLAP_REASON_MASK; + lfa_sts |= ((lfa_status & LFA_LINK_FLAP_REASON_MASK) << + LFA_LINK_FLAP_REASON_OFFSET); + + /* Increment link flap counter */ + lfa_sts = ((lfa_sts & ~LINK_FLAP_COUNT_MASK) | + (((((lfa_sts & LINK_FLAP_COUNT_MASK) >> + LINK_FLAP_COUNT_OFFSET) + 1) & 0xff) + << LINK_FLAP_COUNT_OFFSET)); + REG_WR(bp, params->lfa_base + + offsetof(struct shmem_lfa, lfa_sts), lfa_sts); + /* Proceed with regular link initialization */ +} + int bnx2x_phy_init(struct link_params *params, struct link_vars *vars) { + int lfa_status; struct bnx2x *bp = params->bp; DP(NETIF_MSG_LINK, "Phy Initialization started\n"); DP(NETIF_MSG_LINK, "(1) req_speed %d, req_flowctrl %d\n", @@ -12390,6 +12667,19 @@ int bnx2x_phy_init(struct link_params *params, struct link_vars *vars) vars->flow_ctrl = BNX2X_FLOW_CTRL_NONE; vars->mac_type = MAC_TYPE_NONE; vars->phy_flags = 0; + /* Driver opens NIG-BRB filters */ + bnx2x_set_rx_filter(params, 1); + /* Check if link flap can be avoided */ + lfa_status = bnx2x_check_lfa(params); + + if (lfa_status == 0) { + DP(NETIF_MSG_LINK, "Link Flap Avoidance in progress\n"); + return bnx2x_avoid_link_flap(params, vars); + } + + DP(NETIF_MSG_LINK, "Cannot avoid link flap lfa_sta=0x%x\n", + lfa_status); + bnx2x_cannot_avoid_link_flap(params, vars, lfa_status); /* Disable attentions */ bnx2x_bits_dis(bp, NIG_REG_MASK_INTERRUPT_PORT0 + params->port*4, @@ -12472,13 +12762,12 @@ int bnx2x_link_reset(struct link_params *params, struct link_vars *vars, REG_WR(bp, NIG_REG_EGRESS_EMAC0_OUT_EN + port*4, 0); } - /* Stop BigMac rx */ - if (!CHIP_IS_E3(bp)) - bnx2x_bmac_rx_disable(bp, port); - else { - bnx2x_xmac_disable(params); - bnx2x_umac_disable(params); - } + if (!CHIP_IS_E3(bp)) { + bnx2x_set_bmac_rx(bp, params->chip_id, port, 0); + } else { + bnx2x_set_xmac_rxtx(params, 0); + bnx2x_set_umac_rxtx(params, 0); + } /* Disable emac */ if (!CHIP_IS_E3(bp)) REG_WR(bp, NIG_REG_NIG_EMAC0_EN + port*4, 0); @@ -12536,6 +12825,56 @@ int bnx2x_link_reset(struct link_params *params, struct link_vars *vars, vars->phy_flags = 0; return 0; } +int bnx2x_lfa_reset(struct link_params *params, + struct link_vars *vars) +{ + struct bnx2x *bp = params->bp; + vars->link_up = 0; + vars->phy_flags = 0; + if (!params->lfa_base) + return bnx2x_link_reset(params, vars, 1); + /* + * Activate NIG drain so that during this time the device won't send + * anything while it is unable to response. + */ + REG_WR(bp, NIG_REG_EGRESS_DRAIN0_MODE + params->port*4, 1); + + /* + * Close gracefully the gate from BMAC to NIG such that no half packets + * are passed. + */ + if (!CHIP_IS_E3(bp)) + bnx2x_set_bmac_rx(bp, params->chip_id, params->port, 0); + + if (CHIP_IS_E3(bp)) { + bnx2x_set_xmac_rxtx(params, 0); + bnx2x_set_umac_rxtx(params, 0); + } + /* Wait 10ms for the pipe to clean up*/ + usleep_range(10000, 20000); + + /* Clean the NIG-BRB using the network filters in a way that will + * not cut a packet in the middle. + */ + bnx2x_set_rx_filter(params, 0); + + /* + * Re-open the gate between the BMAC and the NIG, after verifying the + * gate to the BRB is closed, otherwise packets may arrive to the + * firmware before driver had initialized it. The target is to achieve + * minimum management protocol down time. + */ + if (!CHIP_IS_E3(bp)) + bnx2x_set_bmac_rx(bp, params->chip_id, params->port, 1); + + if (CHIP_IS_E3(bp)) { + bnx2x_set_xmac_rxtx(params, 1); + bnx2x_set_umac_rxtx(params, 1); + } + /* Disable NIG drain */ + REG_WR(bp, NIG_REG_EGRESS_DRAIN0_MODE + params->port*4, 0); + return 0; +} /****************************************************************************/ /* Common function */ diff --git a/drivers/net/ethernet/broadcom/bnx2x/bnx2x_link.h b/drivers/net/ethernet/broadcom/bnx2x/bnx2x_link.h index ffc83f3c9123..21c3e42ec6a8 100644 --- a/drivers/net/ethernet/broadcom/bnx2x/bnx2x_link.h +++ b/drivers/net/ethernet/broadcom/bnx2x/bnx2x_link.h @@ -305,6 +305,8 @@ struct link_params { struct bnx2x *bp; u16 req_fc_auto_adv; /* Should be set to TX / BOTH when req_flow_ctrl is set to AUTO */ + u16 rsrv1; + u32 lfa_base; }; /* Output parameters */