diff --git a/drivers/block/Kconfig b/drivers/block/Kconfig index 824e09c4d0d7..e29a44e78e15 100644 --- a/drivers/block/Kconfig +++ b/drivers/block/Kconfig @@ -63,19 +63,6 @@ config AMIGA_Z2RAM To compile this driver as a module, choose M here: the module will be called z2ram. -config BLK_DEV_XD - tristate "XT hard disk support" - depends on ISA && ISA_DMA_API - select CHECK_SIGNATURE - help - Very old 8 bit hard disk controllers used in the IBM XT computer - will be supported if you say Y here. - - To compile this driver as a module, choose M here: the - module will be called xd. - - It's pretty unlikely that you have one of these: say N. - config GDROM tristate "SEGA Dreamcast GD-ROM drive" depends on SH_DREAMCAST diff --git a/drivers/block/Makefile b/drivers/block/Makefile index 17e82df3df74..5195c1f61b2a 100644 --- a/drivers/block/Makefile +++ b/drivers/block/Makefile @@ -15,7 +15,6 @@ obj-$(CONFIG_ATARI_FLOPPY) += ataflop.o obj-$(CONFIG_AMIGA_Z2RAM) += z2ram.o obj-$(CONFIG_BLK_DEV_RAM) += brd.o obj-$(CONFIG_BLK_DEV_LOOP) += loop.o -obj-$(CONFIG_BLK_DEV_XD) += xd.o obj-$(CONFIG_BLK_CPQ_DA) += cpqarray.o obj-$(CONFIG_BLK_CPQ_CISS_DA) += cciss.o obj-$(CONFIG_BLK_DEV_DAC960) += DAC960.o diff --git a/drivers/block/xd.c b/drivers/block/xd.c deleted file mode 100644 index ff540520bada..000000000000 --- a/drivers/block/xd.c +++ /dev/null @@ -1,1123 +0,0 @@ -/* - * This file contains the driver for an XT hard disk controller - * (at least the DTC 5150X) for Linux. - * - * Author: Pat Mackinlay, pat@it.com.au - * Date: 29/09/92 - * - * Revised: 01/01/93, ... - * - * Ref: DTC 5150X Controller Specification (thanks to Kevin Fowler, - * kevinf@agora.rain.com) - * Also thanks to: Salvador Abreu, Dave Thaler, Risto Kankkunen and - * Wim Van Dorst. - * - * Revised: 04/04/94 by Risto Kankkunen - * Moved the detection code from xd_init() to xd_geninit() as it needed - * interrupts enabled and Linus didn't want to enable them in that first - * phase. xd_geninit() is the place to do these kinds of things anyway, - * he says. - * - * Modularized: 04/10/96 by Todd Fries, tfries@umr.edu - * - * Revised: 13/12/97 by Andrzej Krzysztofowicz, ankry@mif.pg.gda.pl - * Fixed some problems with disk initialization and module initiation. - * Added support for manual geometry setting (except Seagate controllers) - * in form: - * xd_geo=,,[,,,] - * Recovered DMA access. Abridged messages. Added support for DTC5051CX, - * WD1002-27X & XEBEC controllers. Driver uses now some jumper settings. - * Extended ioctl() support. - * - * Bugfix: 15/02/01, Paul G. - inform queue layer of tiny xd_maxsect. - * - */ - -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include - -#include -#include - -#include "xd.h" - -static DEFINE_MUTEX(xd_mutex); -static void __init do_xd_setup (int *integers); -#ifdef MODULE -static int xd[5] = { -1,-1,-1,-1, }; -#endif - -#define XD_DONT_USE_DMA 0 /* Initial value. may be overriden using - "nodma" module option */ -#define XD_INIT_DISK_DELAY (30) /* 30 ms delay during disk initialization */ - -/* Above may need to be increased if a problem with the 2nd drive detection - (ST11M controller) or resetting a controller (WD) appears */ - -static XD_INFO xd_info[XD_MAXDRIVES]; - -/* If you try this driver and find that your card is not detected by the driver at bootup, you need to add your BIOS - signature and details to the following list of signatures. A BIOS signature is a string embedded into the first - few bytes of your controller's on-board ROM BIOS. To find out what yours is, use something like MS-DOS's DEBUG - command. Run DEBUG, and then you can examine your BIOS signature with: - - d xxxx:0000 - - where xxxx is the segment of your controller (like C800 or D000 or something). On the ASCII dump at the right, you should - be able to see a string mentioning the manufacturer's copyright etc. Add this string into the table below. The parameters - in the table are, in order: - - offset ; this is the offset (in bytes) from the start of your ROM where the signature starts - signature ; this is the actual text of the signature - xd_?_init_controller ; this is the controller init routine used by your controller - xd_?_init_drive ; this is the drive init routine used by your controller - - The controllers directly supported at the moment are: DTC 5150x, WD 1004A27X, ST11M/R and override. If your controller is - made by the same manufacturer as one of these, try using the same init routines as they do. If that doesn't work, your - best bet is to use the "override" routines. These routines use a "portable" method of getting the disk's geometry, and - may work with your card. If none of these seem to work, try sending me some email and I'll see what I can do . - - NOTE: You can now specify your XT controller's parameters from the command line in the form xd=TYPE,IRQ,IO,DMA. The driver - should be able to detect your drive's geometry from this info. (eg: xd=0,5,0x320,3 is the "standard"). */ - -#include -#define xd_dma_mem_alloc(size) __get_dma_pages(GFP_KERNEL,get_order(size)) -#define xd_dma_mem_free(addr, size) free_pages(addr, get_order(size)) -static char *xd_dma_buffer; - -static XD_SIGNATURE xd_sigs[] __initdata = { - { 0x0000,"Override geometry handler",NULL,xd_override_init_drive,"n unknown" }, /* Pat Mackinlay, pat@it.com.au */ - { 0x0008,"[BXD06 (C) DTC 17-MAY-1985]",xd_dtc_init_controller,xd_dtc5150cx_init_drive," DTC 5150CX" }, /* Andrzej Krzysztofowicz, ankry@mif.pg.gda.pl */ - { 0x000B,"CRD18A Not an IBM rom. (C) Copyright Data Technology Corp. 05/31/88",xd_dtc_init_controller,xd_dtc_init_drive," DTC 5150X" }, /* Todd Fries, tfries@umr.edu */ - { 0x000B,"CXD23A Not an IBM ROM (C)Copyright Data Technology Corp 12/03/88",xd_dtc_init_controller,xd_dtc_init_drive," DTC 5150X" }, /* Pat Mackinlay, pat@it.com.au */ - { 0x0008,"07/15/86(C) Copyright 1986 Western Digital Corp.",xd_wd_init_controller,xd_wd_init_drive," Western Dig. 1002-27X" }, /* Andrzej Krzysztofowicz, ankry@mif.pg.gda.pl */ - { 0x0008,"06/24/88(C) Copyright 1988 Western Digital Corp.",xd_wd_init_controller,xd_wd_init_drive," Western Dig. WDXT-GEN2" }, /* Dan Newcombe, newcombe@aa.csc.peachnet.edu */ - { 0x0015,"SEAGATE ST11 BIOS REVISION",xd_seagate_init_controller,xd_seagate_init_drive," Seagate ST11M/R" }, /* Salvador Abreu, spa@fct.unl.pt */ - { 0x0010,"ST11R BIOS",xd_seagate_init_controller,xd_seagate_init_drive," Seagate ST11M/R" }, /* Risto Kankkunen, risto.kankkunen@cs.helsinki.fi */ - { 0x0010,"ST11 BIOS v1.7",xd_seagate_init_controller,xd_seagate_init_drive," Seagate ST11R" }, /* Alan Hourihane, alanh@fairlite.demon.co.uk */ - { 0x1000,"(c)Copyright 1987 SMS",xd_omti_init_controller,xd_omti_init_drive,"n OMTI 5520" }, /* Dirk Melchers, dirk@merlin.nbg.sub.org */ - { 0x0006,"COPYRIGHT XEBEC (C) 1984",xd_xebec_init_controller,xd_xebec_init_drive," XEBEC" }, /* Andrzej Krzysztofowicz, ankry@mif.pg.gda.pl */ - { 0x0008,"(C) Copyright 1984 Western Digital Corp", xd_wd_init_controller, xd_wd_init_drive," Western Dig. 1002s-wx2" }, - { 0x0008,"(C) Copyright 1986 Western Digital Corporation", xd_wd_init_controller, xd_wd_init_drive," 1986 Western Digital" }, /* jfree@sovereign.org */ -}; - -static unsigned int xd_bases[] __initdata = -{ - 0xC8000, 0xCA000, 0xCC000, - 0xCE000, 0xD0000, 0xD2000, - 0xD4000, 0xD6000, 0xD8000, - 0xDA000, 0xDC000, 0xDE000, - 0xE0000 -}; - -static DEFINE_SPINLOCK(xd_lock); - -static struct gendisk *xd_gendisk[2]; - -static int xd_getgeo(struct block_device *bdev, struct hd_geometry *geo); - -static const struct block_device_operations xd_fops = { - .owner = THIS_MODULE, - .ioctl = xd_ioctl, - .getgeo = xd_getgeo, -}; -static DECLARE_WAIT_QUEUE_HEAD(xd_wait_int); -static u_char xd_drives, xd_irq = 5, xd_dma = 3, xd_maxsectors; -static u_char xd_override __initdata = 0, xd_type __initdata = 0; -static u_short xd_iobase = 0x320; -static int xd_geo[XD_MAXDRIVES*3] __initdata = { 0, }; - -static volatile int xdc_busy; -static struct timer_list xd_watchdog_int; - -static volatile u_char xd_error; -static bool nodma = XD_DONT_USE_DMA; - -static struct request_queue *xd_queue; - -/* xd_init: register the block device number and set up pointer tables */ -static int __init xd_init(void) -{ - u_char i,controller; - unsigned int address; - int err; - -#ifdef MODULE - { - u_char count = 0; - for (i = 4; i > 0; i--) - if (((xd[i] = xd[i-1]) >= 0) && !count) - count = i; - if ((xd[0] = count)) - do_xd_setup(xd); - } -#endif - - init_timer (&xd_watchdog_int); xd_watchdog_int.function = xd_watchdog; - - err = -EBUSY; - if (register_blkdev(XT_DISK_MAJOR, "xd")) - goto out1; - - err = -ENOMEM; - xd_queue = blk_init_queue(do_xd_request, &xd_lock); - if (!xd_queue) - goto out1a; - - if (xd_detect(&controller,&address)) { - - printk("Detected a%s controller (type %d) at address %06x\n", - xd_sigs[controller].name,controller,address); - if (!request_region(xd_iobase,4,"xd")) { - printk("xd: Ports at 0x%x are not available\n", - xd_iobase); - goto out2; - } - if (controller) - xd_sigs[controller].init_controller(address); - xd_drives = xd_initdrives(xd_sigs[controller].init_drive); - - printk("Detected %d hard drive%s (using IRQ%d & DMA%d)\n", - xd_drives,xd_drives == 1 ? "" : "s",xd_irq,xd_dma); - } - - /* - * With the drive detected, xd_maxsectors should now be known. - * If xd_maxsectors is 0, nothing was detected and we fall through - * to return -ENODEV - */ - if (!xd_dma_buffer && xd_maxsectors) { - xd_dma_buffer = (char *)xd_dma_mem_alloc(xd_maxsectors * 0x200); - if (!xd_dma_buffer) { - printk(KERN_ERR "xd: Out of memory.\n"); - goto out3; - } - } - - err = -ENODEV; - if (!xd_drives) - goto out3; - - for (i = 0; i < xd_drives; i++) { - XD_INFO *p = &xd_info[i]; - struct gendisk *disk = alloc_disk(64); - if (!disk) - goto Enomem; - p->unit = i; - disk->major = XT_DISK_MAJOR; - disk->first_minor = i<<6; - sprintf(disk->disk_name, "xd%c", i+'a'); - disk->fops = &xd_fops; - disk->private_data = p; - disk->queue = xd_queue; - set_capacity(disk, p->heads * p->cylinders * p->sectors); - printk(" %s: CHS=%d/%d/%d\n", disk->disk_name, - p->cylinders, p->heads, p->sectors); - xd_gendisk[i] = disk; - } - - err = -EBUSY; - if (request_irq(xd_irq,xd_interrupt_handler, 0, "XT hard disk", NULL)) { - printk("xd: unable to get IRQ%d\n",xd_irq); - goto out4; - } - - if (request_dma(xd_dma,"xd")) { - printk("xd: unable to get DMA%d\n",xd_dma); - goto out5; - } - - /* xd_maxsectors depends on controller - so set after detection */ - blk_queue_max_hw_sectors(xd_queue, xd_maxsectors); - - for (i = 0; i < xd_drives; i++) - add_disk(xd_gendisk[i]); - - return 0; - -out5: - free_irq(xd_irq, NULL); -out4: - for (i = 0; i < xd_drives; i++) - put_disk(xd_gendisk[i]); -out3: - if (xd_maxsectors) - release_region(xd_iobase,4); - - if (xd_dma_buffer) - xd_dma_mem_free((unsigned long)xd_dma_buffer, - xd_maxsectors * 0x200); -out2: - blk_cleanup_queue(xd_queue); -out1a: - unregister_blkdev(XT_DISK_MAJOR, "xd"); -out1: - return err; -Enomem: - err = -ENOMEM; - while (i--) - put_disk(xd_gendisk[i]); - goto out3; -} - -/* xd_detect: scan the possible BIOS ROM locations for the signature strings */ -static u_char __init xd_detect (u_char *controller, unsigned int *address) -{ - int i, j; - - if (xd_override) - { - *controller = xd_type; - *address = 0; - return(1); - } - - for (i = 0; i < ARRAY_SIZE(xd_bases); i++) { - void __iomem *p = ioremap(xd_bases[i], 0x2000); - if (!p) - continue; - for (j = 1; j < ARRAY_SIZE(xd_sigs); j++) { - const char *s = xd_sigs[j].string; - if (check_signature(p + xd_sigs[j].offset, s, strlen(s))) { - *controller = j; - xd_type = j; - *address = xd_bases[i]; - iounmap(p); - return 1; - } - } - iounmap(p); - } - return 0; -} - -/* do_xd_request: handle an incoming request */ -static void do_xd_request (struct request_queue * q) -{ - struct request *req; - - if (xdc_busy) - return; - - req = blk_fetch_request(q); - while (req) { - unsigned block = blk_rq_pos(req); - unsigned count = blk_rq_cur_sectors(req); - XD_INFO *disk = req->rq_disk->private_data; - int res = -EIO; - int retry; - - if (req->cmd_type != REQ_TYPE_FS) - goto done; - if (block + count > get_capacity(req->rq_disk)) - goto done; - for (retry = 0; (retry < XD_RETRIES) && !res; retry++) - res = xd_readwrite(rq_data_dir(req), disk, req->buffer, - block, count); - done: - /* wrap up, 0 = success, -errno = fail */ - if (!__blk_end_request_cur(req, res)) - req = blk_fetch_request(q); - } -} - -static int xd_getgeo(struct block_device *bdev, struct hd_geometry *geo) -{ - XD_INFO *p = bdev->bd_disk->private_data; - - geo->heads = p->heads; - geo->sectors = p->sectors; - geo->cylinders = p->cylinders; - return 0; -} - -/* xd_ioctl: handle device ioctl's */ -static int xd_locked_ioctl(struct block_device *bdev, fmode_t mode, u_int cmd, u_long arg) -{ - switch (cmd) { - case HDIO_SET_DMA: - if (!capable(CAP_SYS_ADMIN)) return -EACCES; - if (xdc_busy) return -EBUSY; - nodma = !arg; - if (nodma && xd_dma_buffer) { - xd_dma_mem_free((unsigned long)xd_dma_buffer, - xd_maxsectors * 0x200); - xd_dma_buffer = NULL; - } else if (!nodma && !xd_dma_buffer) { - xd_dma_buffer = (char *)xd_dma_mem_alloc(xd_maxsectors * 0x200); - if (!xd_dma_buffer) { - nodma = XD_DONT_USE_DMA; - return -ENOMEM; - } - } - return 0; - case HDIO_GET_DMA: - return put_user(!nodma, (long __user *) arg); - case HDIO_GET_MULTCOUNT: - return put_user(xd_maxsectors, (long __user *) arg); - default: - return -EINVAL; - } -} - -static int xd_ioctl(struct block_device *bdev, fmode_t mode, - unsigned int cmd, unsigned long param) -{ - int ret; - - mutex_lock(&xd_mutex); - ret = xd_locked_ioctl(bdev, mode, cmd, param); - mutex_unlock(&xd_mutex); - - return ret; -} - -/* xd_readwrite: handle a read/write request */ -static int xd_readwrite (u_char operation,XD_INFO *p,char *buffer,u_int block,u_int count) -{ - int drive = p->unit; - u_char cmdblk[6],sense[4]; - u_short track,cylinder; - u_char head,sector,control,mode = PIO_MODE,temp; - char **real_buffer; - register int i; - -#ifdef DEBUG_READWRITE - printk("xd_readwrite: operation = %s, drive = %d, buffer = 0x%X, block = %d, count = %d\n",operation == READ ? "read" : "write",drive,buffer,block,count); -#endif /* DEBUG_READWRITE */ - - spin_unlock_irq(&xd_lock); - - control = p->control; - if (!xd_dma_buffer) - xd_dma_buffer = (char *)xd_dma_mem_alloc(xd_maxsectors * 0x200); - while (count) { - temp = count < xd_maxsectors ? count : xd_maxsectors; - - track = block / p->sectors; - head = track % p->heads; - cylinder = track / p->heads; - sector = block % p->sectors; - -#ifdef DEBUG_READWRITE - printk("xd_readwrite: drive = %d, head = %d, cylinder = %d, sector = %d, count = %d\n",drive,head,cylinder,sector,temp); -#endif /* DEBUG_READWRITE */ - - if (xd_dma_buffer) { - mode = xd_setup_dma(operation == READ ? DMA_MODE_READ : DMA_MODE_WRITE,(u_char *)(xd_dma_buffer),temp * 0x200); - real_buffer = &xd_dma_buffer; - for (i=0; i < (temp * 0x200); i++) - xd_dma_buffer[i] = buffer[i]; - } - else - real_buffer = &buffer; - - xd_build(cmdblk,operation == READ ? CMD_READ : CMD_WRITE,drive,head,cylinder,sector,temp & 0xFF,control); - - switch (xd_command(cmdblk,mode,(u_char *)(*real_buffer),(u_char *)(*real_buffer),sense,XD_TIMEOUT)) { - case 1: - printk("xd%c: %s timeout, recalibrating drive\n",'a'+drive,(operation == READ ? "read" : "write")); - xd_recalibrate(drive); - spin_lock_irq(&xd_lock); - return -EIO; - case 2: - if (sense[0] & 0x30) { - printk("xd%c: %s - ",'a'+drive,(operation == READ ? "reading" : "writing")); - switch ((sense[0] & 0x30) >> 4) { - case 0: printk("drive error, code = 0x%X",sense[0] & 0x0F); - break; - case 1: printk("controller error, code = 0x%X",sense[0] & 0x0F); - break; - case 2: printk("command error, code = 0x%X",sense[0] & 0x0F); - break; - case 3: printk("miscellaneous error, code = 0x%X",sense[0] & 0x0F); - break; - } - } - if (sense[0] & 0x80) - printk(" - CHS = %d/%d/%d\n",((sense[2] & 0xC0) << 2) | sense[3],sense[1] & 0x1F,sense[2] & 0x3F); - /* reported drive number = (sense[1] & 0xE0) >> 5 */ - else - printk(" - no valid disk address\n"); - spin_lock_irq(&xd_lock); - return -EIO; - } - if (xd_dma_buffer) - for (i=0; i < (temp * 0x200); i++) - buffer[i] = xd_dma_buffer[i]; - - count -= temp, buffer += temp * 0x200, block += temp; - } - spin_lock_irq(&xd_lock); - return 0; -} - -/* xd_recalibrate: recalibrate a given drive and reset controller if necessary */ -static void xd_recalibrate (u_char drive) -{ - u_char cmdblk[6]; - - xd_build(cmdblk,CMD_RECALIBRATE,drive,0,0,0,0,0); - if (xd_command(cmdblk,PIO_MODE,NULL,NULL,NULL,XD_TIMEOUT * 8)) - printk("xd%c: warning! error recalibrating, controller may be unstable\n", 'a'+drive); -} - -/* xd_interrupt_handler: interrupt service routine */ -static irqreturn_t xd_interrupt_handler(int irq, void *dev_id) -{ - if (inb(XD_STATUS) & STAT_INTERRUPT) { /* check if it was our device */ -#ifdef DEBUG_OTHER - printk("xd_interrupt_handler: interrupt detected\n"); -#endif /* DEBUG_OTHER */ - outb(0,XD_CONTROL); /* acknowledge interrupt */ - wake_up(&xd_wait_int); /* and wake up sleeping processes */ - return IRQ_HANDLED; - } - else - printk("xd: unexpected interrupt\n"); - return IRQ_NONE; -} - -/* xd_setup_dma: set up the DMA controller for a data transfer */ -static u_char xd_setup_dma (u_char mode,u_char *buffer,u_int count) -{ - unsigned long f; - - if (nodma) - return (PIO_MODE); - if (((unsigned long) buffer & 0xFFFF0000) != (((unsigned long) buffer + count) & 0xFFFF0000)) { -#ifdef DEBUG_OTHER - printk("xd_setup_dma: using PIO, transfer overlaps 64k boundary\n"); -#endif /* DEBUG_OTHER */ - return (PIO_MODE); - } - - f=claim_dma_lock(); - disable_dma(xd_dma); - clear_dma_ff(xd_dma); - set_dma_mode(xd_dma,mode); - set_dma_addr(xd_dma, (unsigned long) buffer); - set_dma_count(xd_dma,count); - - release_dma_lock(f); - - return (DMA_MODE); /* use DMA and INT */ -} - -/* xd_build: put stuff into an array in a format suitable for the controller */ -static u_char *xd_build (u_char *cmdblk,u_char command,u_char drive,u_char head,u_short cylinder,u_char sector,u_char count,u_char control) -{ - cmdblk[0] = command; - cmdblk[1] = ((drive & 0x07) << 5) | (head & 0x1F); - cmdblk[2] = ((cylinder & 0x300) >> 2) | (sector & 0x3F); - cmdblk[3] = cylinder & 0xFF; - cmdblk[4] = count; - cmdblk[5] = control; - - return (cmdblk); -} - -static void xd_watchdog (unsigned long unused) -{ - xd_error = 1; - wake_up(&xd_wait_int); -} - -/* xd_waitport: waits until port & mask == flags or a timeout occurs. return 1 for a timeout */ -static inline u_char xd_waitport (u_short port,u_char flags,u_char mask,u_long timeout) -{ - u_long expiry = jiffies + timeout; - int success; - - xdc_busy = 1; - while ((success = ((inb(port) & mask) != flags)) && time_before(jiffies, expiry)) - schedule_timeout_uninterruptible(1); - xdc_busy = 0; - return (success); -} - -static inline u_int xd_wait_for_IRQ (void) -{ - unsigned long flags; - xd_watchdog_int.expires = jiffies + 8 * HZ; - add_timer(&xd_watchdog_int); - - flags=claim_dma_lock(); - enable_dma(xd_dma); - release_dma_lock(flags); - - sleep_on(&xd_wait_int); - del_timer(&xd_watchdog_int); - xdc_busy = 0; - - flags=claim_dma_lock(); - disable_dma(xd_dma); - release_dma_lock(flags); - - if (xd_error) { - printk("xd: missed IRQ - command aborted\n"); - xd_error = 0; - return (1); - } - return (0); -} - -/* xd_command: handle all data transfers necessary for a single command */ -static u_int xd_command (u_char *command,u_char mode,u_char *indata,u_char *outdata,u_char *sense,u_long timeout) -{ - u_char cmdblk[6],csb,complete = 0; - -#ifdef DEBUG_COMMAND - printk("xd_command: command = 0x%X, mode = 0x%X, indata = 0x%X, outdata = 0x%X, sense = 0x%X\n",command,mode,indata,outdata,sense); -#endif /* DEBUG_COMMAND */ - - outb(0,XD_SELECT); - outb(mode,XD_CONTROL); - - if (xd_waitport(XD_STATUS,STAT_SELECT,STAT_SELECT,timeout)) - return (1); - - while (!complete) { - if (xd_waitport(XD_STATUS,STAT_READY,STAT_READY,timeout)) - return (1); - - switch (inb(XD_STATUS) & (STAT_COMMAND | STAT_INPUT)) { - case 0: - if (mode == DMA_MODE) { - if (xd_wait_for_IRQ()) - return (1); - } else - outb(outdata ? *outdata++ : 0,XD_DATA); - break; - case STAT_INPUT: - if (mode == DMA_MODE) { - if (xd_wait_for_IRQ()) - return (1); - } else - if (indata) - *indata++ = inb(XD_DATA); - else - inb(XD_DATA); - break; - case STAT_COMMAND: - outb(command ? *command++ : 0,XD_DATA); - break; - case STAT_COMMAND | STAT_INPUT: - complete = 1; - break; - } - } - csb = inb(XD_DATA); - - if (xd_waitport(XD_STATUS,0,STAT_SELECT,timeout)) /* wait until deselected */ - return (1); - - if (csb & CSB_ERROR) { /* read sense data if error */ - xd_build(cmdblk,CMD_SENSE,(csb & CSB_LUN) >> 5,0,0,0,0,0); - if (xd_command(cmdblk,0,sense,NULL,NULL,XD_TIMEOUT)) - printk("xd: warning! sense command failed!\n"); - } - -#ifdef DEBUG_COMMAND - printk("xd_command: completed with csb = 0x%X\n",csb); -#endif /* DEBUG_COMMAND */ - - return (csb & CSB_ERROR); -} - -static u_char __init xd_initdrives (void (*init_drive)(u_char drive)) -{ - u_char cmdblk[6],i,count = 0; - - for (i = 0; i < XD_MAXDRIVES; i++) { - xd_build(cmdblk,CMD_TESTREADY,i,0,0,0,0,0); - if (!xd_command(cmdblk,PIO_MODE,NULL,NULL,NULL,XD_TIMEOUT*8)) { - msleep_interruptible(XD_INIT_DISK_DELAY); - - init_drive(count); - count++; - - msleep_interruptible(XD_INIT_DISK_DELAY); - } - } - return (count); -} - -static void __init xd_manual_geo_set (u_char drive) -{ - xd_info[drive].heads = (u_char)(xd_geo[3 * drive + 1]); - xd_info[drive].cylinders = (u_short)(xd_geo[3 * drive]); - xd_info[drive].sectors = (u_char)(xd_geo[3 * drive + 2]); -} - -static void __init xd_dtc_init_controller (unsigned int address) -{ - switch (address) { - case 0x00000: - case 0xC8000: break; /*initial: 0x320 */ - case 0xCA000: xd_iobase = 0x324; - case 0xD0000: /*5150CX*/ - case 0xD8000: break; /*5150CX & 5150XL*/ - default: printk("xd_dtc_init_controller: unsupported BIOS address %06x\n",address); - break; - } - xd_maxsectors = 0x01; /* my card seems to have trouble doing multi-block transfers? */ - - outb(0,XD_RESET); /* reset the controller */ -} - - -static void __init xd_dtc5150cx_init_drive (u_char drive) -{ - /* values from controller's BIOS - BIOS chip may be removed */ - static u_short geometry_table[][4] = { - {0x200,8,0x200,0x100}, - {0x267,2,0x267,0x267}, - {0x264,4,0x264,0x80}, - {0x132,4,0x132,0x0}, - {0x132,2,0x80, 0x132}, - {0x177,8,0x177,0x0}, - {0x132,8,0x84, 0x0}, - {}, /* not used */ - {0x132,6,0x80, 0x100}, - {0x200,6,0x100,0x100}, - {0x264,2,0x264,0x80}, - {0x280,4,0x280,0x100}, - {0x2B9,3,0x2B9,0x2B9}, - {0x2B9,5,0x2B9,0x2B9}, - {0x280,6,0x280,0x100}, - {0x132,4,0x132,0x0}}; - u_char n; - - n = inb(XD_JUMPER); - n = (drive ? n : (n >> 2)) & 0x33; - n = (n | (n >> 2)) & 0x0F; - if (xd_geo[3*drive]) - xd_manual_geo_set(drive); - else - if (n != 7) { - xd_info[drive].heads = (u_char)(geometry_table[n][1]); /* heads */ - xd_info[drive].cylinders = geometry_table[n][0]; /* cylinders */ - xd_info[drive].sectors = 17; /* sectors */ -#if 0 - xd_info[drive].rwrite = geometry_table[n][2]; /* reduced write */ - xd_info[drive].precomp = geometry_table[n][3] /* write precomp */ - xd_info[drive].ecc = 0x0B; /* ecc length */ -#endif /* 0 */ - } - else { - printk("xd%c: undetermined drive geometry\n",'a'+drive); - return; - } - xd_info[drive].control = 5; /* control byte */ - xd_setparam(CMD_DTCSETPARAM,drive,xd_info[drive].heads,xd_info[drive].cylinders,geometry_table[n][2],geometry_table[n][3],0x0B); - xd_recalibrate(drive); -} - -static void __init xd_dtc_init_drive (u_char drive) -{ - u_char cmdblk[6],buf[64]; - - xd_build(cmdblk,CMD_DTCGETGEOM,drive,0,0,0,0,0); - if (!xd_command(cmdblk,PIO_MODE,buf,NULL,NULL,XD_TIMEOUT * 2)) { - xd_info[drive].heads = buf[0x0A]; /* heads */ - xd_info[drive].cylinders = ((u_short *) (buf))[0x04]; /* cylinders */ - xd_info[drive].sectors = 17; /* sectors */ - if (xd_geo[3*drive]) - xd_manual_geo_set(drive); -#if 0 - xd_info[drive].rwrite = ((u_short *) (buf + 1))[0x05]; /* reduced write */ - xd_info[drive].precomp = ((u_short *) (buf + 1))[0x06]; /* write precomp */ - xd_info[drive].ecc = buf[0x0F]; /* ecc length */ -#endif /* 0 */ - xd_info[drive].control = 0; /* control byte */ - - xd_setparam(CMD_DTCSETPARAM,drive,xd_info[drive].heads,xd_info[drive].cylinders,((u_short *) (buf + 1))[0x05],((u_short *) (buf + 1))[0x06],buf[0x0F]); - xd_build(cmdblk,CMD_DTCSETSTEP,drive,0,0,0,0,7); - if (xd_command(cmdblk,PIO_MODE,NULL,NULL,NULL,XD_TIMEOUT * 2)) - printk("xd_dtc_init_drive: error setting step rate for xd%c\n", 'a'+drive); - } - else - printk("xd_dtc_init_drive: error reading geometry for xd%c\n", 'a'+drive); -} - -static void __init xd_wd_init_controller (unsigned int address) -{ - switch (address) { - case 0x00000: - case 0xC8000: break; /*initial: 0x320 */ - case 0xCA000: xd_iobase = 0x324; break; - case 0xCC000: xd_iobase = 0x328; break; - case 0xCE000: xd_iobase = 0x32C; break; - case 0xD0000: xd_iobase = 0x328; break; /* ? */ - case 0xD8000: xd_iobase = 0x32C; break; /* ? */ - default: printk("xd_wd_init_controller: unsupported BIOS address %06x\n",address); - break; - } - xd_maxsectors = 0x01; /* this one doesn't wrap properly either... */ - - outb(0,XD_RESET); /* reset the controller */ - - msleep(XD_INIT_DISK_DELAY); -} - -static void __init xd_wd_init_drive (u_char drive) -{ - /* values from controller's BIOS - BIOS may be disabled */ - static u_short geometry_table[][4] = { - {0x264,4,0x1C2,0x1C2}, /* common part */ - {0x132,4,0x099,0x0}, - {0x267,2,0x1C2,0x1C2}, - {0x267,4,0x1C2,0x1C2}, - - {0x334,6,0x335,0x335}, /* 1004 series RLL */ - {0x30E,4,0x30F,0x3DC}, - {0x30E,2,0x30F,0x30F}, - {0x267,4,0x268,0x268}, - - {0x3D5,5,0x3D6,0x3D6}, /* 1002 series RLL */ - {0x3DB,7,0x3DC,0x3DC}, - {0x264,4,0x265,0x265}, - {0x267,4,0x268,0x268}}; - - u_char cmdblk[6],buf[0x200]; - u_char n = 0,rll,jumper_state,use_jumper_geo; - u_char wd_1002 = (xd_sigs[xd_type].string[7] == '6'); - - jumper_state = ~(inb(0x322)); - if (jumper_state & 0x40) - xd_irq = 9; - rll = (jumper_state & 0x30) ? (0x04 << wd_1002) : 0; - xd_build(cmdblk,CMD_READ,drive,0,0,0,1,0); - if (!xd_command(cmdblk,PIO_MODE,buf,NULL,NULL,XD_TIMEOUT * 2)) { - xd_info[drive].heads = buf[0x1AF]; /* heads */ - xd_info[drive].cylinders = ((u_short *) (buf + 1))[0xD6]; /* cylinders */ - xd_info[drive].sectors = 17; /* sectors */ - if (xd_geo[3*drive]) - xd_manual_geo_set(drive); -#if 0 - xd_info[drive].rwrite = ((u_short *) (buf))[0xD8]; /* reduced write */ - xd_info[drive].wprecomp = ((u_short *) (buf))[0xDA]; /* write precomp */ - xd_info[drive].ecc = buf[0x1B4]; /* ecc length */ -#endif /* 0 */ - xd_info[drive].control = buf[0x1B5]; /* control byte */ - use_jumper_geo = !(xd_info[drive].heads) || !(xd_info[drive].cylinders); - if (xd_geo[3*drive]) { - xd_manual_geo_set(drive); - xd_info[drive].control = rll ? 7 : 5; - } - else if (use_jumper_geo) { - n = (((jumper_state & 0x0F) >> (drive << 1)) & 0x03) | rll; - xd_info[drive].cylinders = geometry_table[n][0]; - xd_info[drive].heads = (u_char)(geometry_table[n][1]); - xd_info[drive].control = rll ? 7 : 5; -#if 0 - xd_info[drive].rwrite = geometry_table[n][2]; - xd_info[drive].wprecomp = geometry_table[n][3]; - xd_info[drive].ecc = 0x0B; -#endif /* 0 */ - } - if (!wd_1002) { - if (use_jumper_geo) - xd_setparam(CMD_WDSETPARAM,drive,xd_info[drive].heads,xd_info[drive].cylinders, - geometry_table[n][2],geometry_table[n][3],0x0B); - else - xd_setparam(CMD_WDSETPARAM,drive,xd_info[drive].heads,xd_info[drive].cylinders, - ((u_short *) (buf))[0xD8],((u_short *) (buf))[0xDA],buf[0x1B4]); - } - /* 1002 based RLL controller requests converted addressing, but reports physical - (physical 26 sec., logical 17 sec.) - 1004 based ???? */ - if (rll & wd_1002) { - if ((xd_info[drive].cylinders *= 26, - xd_info[drive].cylinders /= 17) > 1023) - xd_info[drive].cylinders = 1023; /* 1024 ? */ -#if 0 - xd_info[drive].rwrite *= 26; - xd_info[drive].rwrite /= 17; - xd_info[drive].wprecomp *= 26 - xd_info[drive].wprecomp /= 17; -#endif /* 0 */ - } - } - else - printk("xd_wd_init_drive: error reading geometry for xd%c\n",'a'+drive); - -} - -static void __init xd_seagate_init_controller (unsigned int address) -{ - switch (address) { - case 0x00000: - case 0xC8000: break; /*initial: 0x320 */ - case 0xD0000: xd_iobase = 0x324; break; - case 0xD8000: xd_iobase = 0x328; break; - case 0xE0000: xd_iobase = 0x32C; break; - default: printk("xd_seagate_init_controller: unsupported BIOS address %06x\n",address); - break; - } - xd_maxsectors = 0x40; - - outb(0,XD_RESET); /* reset the controller */ -} - -static void __init xd_seagate_init_drive (u_char drive) -{ - u_char cmdblk[6],buf[0x200]; - - xd_build(cmdblk,CMD_ST11GETGEOM,drive,0,0,0,1,0); - if (!xd_command(cmdblk,PIO_MODE,buf,NULL,NULL,XD_TIMEOUT * 2)) { - xd_info[drive].heads = buf[0x04]; /* heads */ - xd_info[drive].cylinders = (buf[0x02] << 8) | buf[0x03]; /* cylinders */ - xd_info[drive].sectors = buf[0x05]; /* sectors */ - xd_info[drive].control = 0; /* control byte */ - } - else - printk("xd_seagate_init_drive: error reading geometry from xd%c\n", 'a'+drive); -} - -/* Omti support courtesy Dirk Melchers */ -static void __init xd_omti_init_controller (unsigned int address) -{ - switch (address) { - case 0x00000: - case 0xC8000: break; /*initial: 0x320 */ - case 0xD0000: xd_iobase = 0x324; break; - case 0xD8000: xd_iobase = 0x328; break; - case 0xE0000: xd_iobase = 0x32C; break; - default: printk("xd_omti_init_controller: unsupported BIOS address %06x\n",address); - break; - } - - xd_maxsectors = 0x40; - - outb(0,XD_RESET); /* reset the controller */ -} - -static void __init xd_omti_init_drive (u_char drive) -{ - /* gets infos from drive */ - xd_override_init_drive(drive); - - /* set other parameters, Hardcoded, not that nice :-) */ - xd_info[drive].control = 2; -} - -/* Xebec support (AK) */ -static void __init xd_xebec_init_controller (unsigned int address) -{ -/* iobase may be set manually in range 0x300 - 0x33C - irq may be set manually to 2(9),3,4,5,6,7 - dma may be set manually to 1,2,3 - (How to detect them ???) -BIOS address may be set manually in range 0x0 - 0xF8000 -If you need non-standard settings use the xd=... command */ - - switch (address) { - case 0x00000: - case 0xC8000: /* initially: xd_iobase==0x320 */ - case 0xD0000: - case 0xD2000: - case 0xD4000: - case 0xD6000: - case 0xD8000: - case 0xDA000: - case 0xDC000: - case 0xDE000: - case 0xE0000: break; - default: printk("xd_xebec_init_controller: unsupported BIOS address %06x\n",address); - break; - } - - xd_maxsectors = 0x01; - outb(0,XD_RESET); /* reset the controller */ - - msleep(XD_INIT_DISK_DELAY); -} - -static void __init xd_xebec_init_drive (u_char drive) -{ - /* values from controller's BIOS - BIOS chip may be removed */ - static u_short geometry_table[][5] = { - {0x132,4,0x080,0x080,0x7}, - {0x132,4,0x080,0x080,0x17}, - {0x264,2,0x100,0x100,0x7}, - {0x264,2,0x100,0x100,0x17}, - {0x132,8,0x080,0x080,0x7}, - {0x132,8,0x080,0x080,0x17}, - {0x264,4,0x100,0x100,0x6}, - {0x264,4,0x100,0x100,0x17}, - {0x2BC,5,0x2BC,0x12C,0x6}, - {0x3A5,4,0x3A5,0x3A5,0x7}, - {0x26C,6,0x26C,0x26C,0x7}, - {0x200,8,0x200,0x100,0x17}, - {0x400,5,0x400,0x400,0x7}, - {0x400,6,0x400,0x400,0x7}, - {0x264,8,0x264,0x200,0x17}, - {0x33E,7,0x33E,0x200,0x7}}; - u_char n; - - n = inb(XD_JUMPER) & 0x0F; /* BIOS's drive number: same geometry - is assumed for BOTH drives */ - if (xd_geo[3*drive]) - xd_manual_geo_set(drive); - else { - xd_info[drive].heads = (u_char)(geometry_table[n][1]); /* heads */ - xd_info[drive].cylinders = geometry_table[n][0]; /* cylinders */ - xd_info[drive].sectors = 17; /* sectors */ -#if 0 - xd_info[drive].rwrite = geometry_table[n][2]; /* reduced write */ - xd_info[drive].precomp = geometry_table[n][3] /* write precomp */ - xd_info[drive].ecc = 0x0B; /* ecc length */ -#endif /* 0 */ - } - xd_info[drive].control = geometry_table[n][4]; /* control byte */ - xd_setparam(CMD_XBSETPARAM,drive,xd_info[drive].heads,xd_info[drive].cylinders,geometry_table[n][2],geometry_table[n][3],0x0B); - xd_recalibrate(drive); -} - -/* xd_override_init_drive: this finds disk geometry in a "binary search" style, narrowing in on the "correct" number of heads - etc. by trying values until it gets the highest successful value. Idea courtesy Salvador Abreu (spa@fct.unl.pt). */ -static void __init xd_override_init_drive (u_char drive) -{ - u_short min[] = { 0,0,0 },max[] = { 16,1024,64 },test[] = { 0,0,0 }; - u_char cmdblk[6],i; - - if (xd_geo[3*drive]) - xd_manual_geo_set(drive); - else { - for (i = 0; i < 3; i++) { - while (min[i] != max[i] - 1) { - test[i] = (min[i] + max[i]) / 2; - xd_build(cmdblk,CMD_SEEK,drive,(u_char) test[0],(u_short) test[1],(u_char) test[2],0,0); - if (!xd_command(cmdblk,PIO_MODE,NULL,NULL,NULL,XD_TIMEOUT * 2)) - min[i] = test[i]; - else - max[i] = test[i]; - } - test[i] = min[i]; - } - xd_info[drive].heads = (u_char) min[0] + 1; - xd_info[drive].cylinders = (u_short) min[1] + 1; - xd_info[drive].sectors = (u_char) min[2] + 1; - } - xd_info[drive].control = 0; -} - -/* xd_setup: initialise controller from command line parameters */ -static void __init do_xd_setup (int *integers) -{ - switch (integers[0]) { - case 4: if (integers[4] < 0) - nodma = 1; - else if (integers[4] < 8) - xd_dma = integers[4]; - case 3: if ((integers[3] > 0) && (integers[3] <= 0x3FC)) - xd_iobase = integers[3]; - case 2: if ((integers[2] > 0) && (integers[2] < 16)) - xd_irq = integers[2]; - case 1: xd_override = 1; - if ((integers[1] >= 0) && (integers[1] < ARRAY_SIZE(xd_sigs))) - xd_type = integers[1]; - case 0: break; - default:printk("xd: too many parameters for xd\n"); - } - xd_maxsectors = 0x01; -} - -/* xd_setparam: set the drive characteristics */ -static void __init xd_setparam (u_char command,u_char drive,u_char heads,u_short cylinders,u_short rwrite,u_short wprecomp,u_char ecc) -{ - u_char cmdblk[14]; - - xd_build(cmdblk,command,drive,0,0,0,0,0); - cmdblk[6] = (u_char) (cylinders >> 8) & 0x03; - cmdblk[7] = (u_char) (cylinders & 0xFF); - cmdblk[8] = heads & 0x1F; - cmdblk[9] = (u_char) (rwrite >> 8) & 0x03; - cmdblk[10] = (u_char) (rwrite & 0xFF); - cmdblk[11] = (u_char) (wprecomp >> 8) & 0x03; - cmdblk[12] = (u_char) (wprecomp & 0xFF); - cmdblk[13] = ecc; - - /* Some controllers require geometry info as data, not command */ - - if (xd_command(cmdblk,PIO_MODE,NULL,&cmdblk[6],NULL,XD_TIMEOUT * 2)) - printk("xd: error setting characteristics for xd%c\n", 'a'+drive); -} - - -#ifdef MODULE - -module_param_array(xd, int, NULL, 0); -module_param_array(xd_geo, int, NULL, 0); -module_param(nodma, bool, 0); - -MODULE_LICENSE("GPL"); - -void cleanup_module(void) -{ - int i; - unregister_blkdev(XT_DISK_MAJOR, "xd"); - for (i = 0; i < xd_drives; i++) { - del_gendisk(xd_gendisk[i]); - put_disk(xd_gendisk[i]); - } - blk_cleanup_queue(xd_queue); - release_region(xd_iobase,4); - if (xd_drives) { - free_irq(xd_irq, NULL); - free_dma(xd_dma); - if (xd_dma_buffer) - xd_dma_mem_free((unsigned long)xd_dma_buffer, xd_maxsectors * 0x200); - } -} -#else - -static int __init xd_setup (char *str) -{ - int ints[5]; - get_options (str, ARRAY_SIZE (ints), ints); - do_xd_setup (ints); - return 1; -} - -/* xd_manual_geo_init: initialise drive geometry from command line parameters - (used only for WD drives) */ -static int __init xd_manual_geo_init (char *str) -{ - int i, integers[1 + 3*XD_MAXDRIVES]; - - get_options (str, ARRAY_SIZE (integers), integers); - if (integers[0]%3 != 0) { - printk("xd: incorrect number of parameters for xd_geo\n"); - return 1; - } - for (i = 0; (i < integers[0]) && (i < 3*XD_MAXDRIVES); i++) - xd_geo[i] = integers[i+1]; - return 1; -} - -__setup ("xd=", xd_setup); -__setup ("xd_geo=", xd_manual_geo_init); - -#endif /* MODULE */ - -module_init(xd_init); -MODULE_ALIAS_BLOCKDEV_MAJOR(XT_DISK_MAJOR); diff --git a/drivers/block/xd.h b/drivers/block/xd.h deleted file mode 100644 index 37cacef16e93..000000000000 --- a/drivers/block/xd.h +++ /dev/null @@ -1,134 +0,0 @@ -#ifndef _LINUX_XD_H -#define _LINUX_XD_H - -/* - * This file contains the definitions for the IO ports and errors etc. for XT hard disk controllers (at least the DTC 5150X). - * - * Author: Pat Mackinlay, pat@it.com.au - * Date: 29/09/92 - * - * Revised: 01/01/93, ... - * - * Ref: DTC 5150X Controller Specification (thanks to Kevin Fowler, kevinf@agora.rain.com) - * Also thanks to: Salvador Abreu, Dave Thaler, Risto Kankkunen and Wim Van Dorst. - */ - -#include - -/* XT hard disk controller registers */ -#define XD_DATA (xd_iobase + 0x00) /* data RW register */ -#define XD_RESET (xd_iobase + 0x01) /* reset WO register */ -#define XD_STATUS (xd_iobase + 0x01) /* status RO register */ -#define XD_SELECT (xd_iobase + 0x02) /* select WO register */ -#define XD_JUMPER (xd_iobase + 0x02) /* jumper RO register */ -#define XD_CONTROL (xd_iobase + 0x03) /* DMAE/INTE WO register */ -#define XD_RESERVED (xd_iobase + 0x03) /* reserved */ - -/* XT hard disk controller commands (incomplete list) */ -#define CMD_TESTREADY 0x00 /* test drive ready */ -#define CMD_RECALIBRATE 0x01 /* recalibrate drive */ -#define CMD_SENSE 0x03 /* request sense */ -#define CMD_FORMATDRV 0x04 /* format drive */ -#define CMD_VERIFY 0x05 /* read verify */ -#define CMD_FORMATTRK 0x06 /* format track */ -#define CMD_FORMATBAD 0x07 /* format bad track */ -#define CMD_READ 0x08 /* read */ -#define CMD_WRITE 0x0A /* write */ -#define CMD_SEEK 0x0B /* seek */ - -/* Controller specific commands */ -#define CMD_DTCSETPARAM 0x0C /* set drive parameters (DTC 5150X & CX only?) */ -#define CMD_DTCGETECC 0x0D /* get ecc error length (DTC 5150X only?) */ -#define CMD_DTCREADBUF 0x0E /* read sector buffer (DTC 5150X only?) */ -#define CMD_DTCWRITEBUF 0x0F /* write sector buffer (DTC 5150X only?) */ -#define CMD_DTCREMAPTRK 0x11 /* assign alternate track (DTC 5150X only?) */ -#define CMD_DTCGETPARAM 0xFB /* get drive parameters (DTC 5150X only?) */ -#define CMD_DTCSETSTEP 0xFC /* set step rate (DTC 5150X only?) */ -#define CMD_DTCSETGEOM 0xFE /* set geometry data (DTC 5150X only?) */ -#define CMD_DTCGETGEOM 0xFF /* get geometry data (DTC 5150X only?) */ -#define CMD_ST11GETGEOM 0xF8 /* get geometry data (Seagate ST11R/M only?) */ -#define CMD_WDSETPARAM 0x0C /* set drive parameters (WD 1004A27X only?) */ -#define CMD_XBSETPARAM 0x0C /* set drive parameters (XEBEC only?) */ - -/* Bits for command status byte */ -#define CSB_ERROR 0x02 /* error */ -#define CSB_LUN 0x20 /* logical Unit Number */ - -/* XT hard disk controller status bits */ -#define STAT_READY 0x01 /* controller is ready */ -#define STAT_INPUT 0x02 /* data flowing from controller to host */ -#define STAT_COMMAND 0x04 /* controller in command phase */ -#define STAT_SELECT 0x08 /* controller is selected */ -#define STAT_REQUEST 0x10 /* controller requesting data */ -#define STAT_INTERRUPT 0x20 /* controller requesting interrupt */ - -/* XT hard disk controller control bits */ -#define PIO_MODE 0x00 /* control bits to set for PIO */ -#define DMA_MODE 0x03 /* control bits to set for DMA & interrupt */ - -#define XD_MAXDRIVES 2 /* maximum 2 drives */ -#define XD_TIMEOUT HZ /* 1 second timeout */ -#define XD_RETRIES 4 /* maximum 4 retries */ - -#undef DEBUG /* define for debugging output */ - -#ifdef DEBUG - #define DEBUG_STARTUP /* debug driver initialisation */ - #define DEBUG_OVERRIDE /* debug override geometry detection */ - #define DEBUG_READWRITE /* debug each read/write command */ - #define DEBUG_OTHER /* debug misc. interrupt/DMA stuff */ - #define DEBUG_COMMAND /* debug each controller command */ -#endif /* DEBUG */ - -/* this structure defines the XT drives and their types */ -typedef struct { - u_char heads; - u_short cylinders; - u_char sectors; - u_char control; - int unit; -} XD_INFO; - -/* this structure defines a ROM BIOS signature */ -typedef struct { - unsigned int offset; - const char *string; - void (*init_controller)(unsigned int address); - void (*init_drive)(u_char drive); - const char *name; -} XD_SIGNATURE; - -#ifndef MODULE -static int xd_manual_geo_init (char *command); -#endif /* MODULE */ -static u_char xd_detect (u_char *controller, unsigned int *address); -static u_char xd_initdrives (void (*init_drive)(u_char drive)); - -static void do_xd_request (struct request_queue * q); -static int xd_ioctl (struct block_device *bdev,fmode_t mode,unsigned int cmd,unsigned long arg); -static int xd_readwrite (u_char operation,XD_INFO *disk,char *buffer,u_int block,u_int count); -static void xd_recalibrate (u_char drive); - -static irqreturn_t xd_interrupt_handler(int irq, void *dev_id); -static u_char xd_setup_dma (u_char opcode,u_char *buffer,u_int count); -static u_char *xd_build (u_char *cmdblk,u_char command,u_char drive,u_char head,u_short cylinder,u_char sector,u_char count,u_char control); -static void xd_watchdog (unsigned long unused); -static inline u_char xd_waitport (u_short port,u_char flags,u_char mask,u_long timeout); -static u_int xd_command (u_char *command,u_char mode,u_char *indata,u_char *outdata,u_char *sense,u_long timeout); - -/* card specific setup and geometry gathering code */ -static void xd_dtc_init_controller (unsigned int address); -static void xd_dtc5150cx_init_drive (u_char drive); -static void xd_dtc_init_drive (u_char drive); -static void xd_wd_init_controller (unsigned int address); -static void xd_wd_init_drive (u_char drive); -static void xd_seagate_init_controller (unsigned int address); -static void xd_seagate_init_drive (u_char drive); -static void xd_omti_init_controller (unsigned int address); -static void xd_omti_init_drive (u_char drive); -static void xd_xebec_init_controller (unsigned int address); -static void xd_xebec_init_drive (u_char drive); -static void xd_setparam (u_char command,u_char drive,u_char heads,u_short cylinders,u_short rwrite,u_short wprecomp,u_char ecc); -static void xd_override_init_drive (u_char drive); - -#endif /* _LINUX_XD_H */