Merge 3.7-rc3 into tty-next

This merges the tty changes in 3.7-rc3 into tty-next

Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Documentation/00-INDEX

@@ -210,6 +210,8 @@ local_ops.txt
 	- semantics and behavior of local atomic operations.
 lockdep-design.txt
 	- documentation on the runtime locking correctness validator.
+lockup-watchdogs.txt
+	- info on soft and hard lockup detectors (aka nmi_watchdog).
 logo.gif
 	- full colour GIF image of Linux logo (penguin - Tux).
 logo.txt
@@ -240,8 +242,6 @@ netlabel/
 	- directory with information on the NetLabel subsystem.
 networking/
 	- directory with info on various aspects of networking with Linux.
-nmi_watchdog.txt
-	- info on NMI watchdog for SMP systems.
 nommu-mmap.txt
 	- documentation about no-mmu memory mapping support.
 numastat.txt

Documentation/devicetree/bindings/arm/atmel-at91.txt

@@ -8,7 +8,7 @@ PIT Timer required properties:
   shared across all System Controller members.
 
 TC/TCLIB Timer required properties:
-- compatible: Should be "atmel,<chip>-pit".
+- compatible: Should be "atmel,<chip>-tcb".
   <chip> can be "at91rm9200" or "at91sam9x5"
 - reg: Should contain registers location and length
 - interrupts: Should contain all interrupts for the TC block

Documentation/devicetree/bindings/pinctrl/nvidia,tegra20-pinmux.txt

@@ -93,7 +93,7 @@ Valid values for pin and group names are:
 
     With some exceptions, these support nvidia,high-speed-mode,
     nvidia,schmitt, nvidia,low-power-mode, nvidia,pull-down-strength,
-    nvidia,pull-up-strength, nvidia,slew_rate-rising, nvidia,slew_rate-falling.
+    nvidia,pull-up-strength, nvidia,slew-rate-rising, nvidia,slew-rate-falling.
 
     drive_ao1, drive_ao2, drive_at1, drive_at2, drive_cdev1, drive_cdev2,
     drive_csus, drive_dap1, drive_dap2, drive_dap3, drive_dap4, drive_dbg,

Documentation/devicetree/bindings/pinctrl/nvidia,tegra30-pinmux.txt

@@ -83,7 +83,7 @@ Valid values for pin and group names are:
   drive groups:
 
     These all support nvidia,pull-down-strength, nvidia,pull-up-strength,
-    nvidia,slew_rate-rising, nvidia,slew_rate-falling. Most but not all
+    nvidia,slew-rate-rising, nvidia,slew-rate-falling. Most but not all
     support nvidia,high-speed-mode, nvidia,schmitt, nvidia,low-power-mode.
 
     ao1, ao2, at1, at2, at3, at4, at5, cdev1, cdev2, cec, crt, csus, dap1,

Documentation/firmware_class/README

@@ -18,32 +18,40 @@
  High level behavior (mixed):
  ============================
 
- kernel(driver): calls request_firmware(&fw_entry, $FIRMWARE, device)
+ 1), kernel(driver):
+	- calls request_firmware(&fw_entry, $FIRMWARE, device)
+	- kernel searchs the fimware image with name $FIRMWARE directly
+	in the below search path of root filesystem:
+		"/lib/firmware/updates/" UTS_RELEASE,
+		"/lib/firmware/updates",
+		"/lib/firmware/" UTS_RELEASE,
+		"/lib/firmware"
+	- If found, goto 7), else goto 2)
 
- userspace:
+ 2), userspace:
  	- /sys/class/firmware/xxx/{loading,data} appear.
 	- hotplug gets called with a firmware identifier in $FIRMWARE
 	  and the usual hotplug environment.
 		- hotplug: echo 1 > /sys/class/firmware/xxx/loading
 
- kernel: Discard any previous partial load.
+ 3), kernel: Discard any previous partial load.
 
- userspace:
+ 4), userspace:
 		- hotplug: cat appropriate_firmware_image > \
 					/sys/class/firmware/xxx/data
 
- kernel: grows a buffer in PAGE_SIZE increments to hold the image as it
+ 5), kernel: grows a buffer in PAGE_SIZE increments to hold the image as it
 	 comes in.
 
- userspace:
+ 6), userspace:
 		- hotplug: echo 0 > /sys/class/firmware/xxx/loading
 
- kernel: request_firmware() returns and the driver has the firmware
+ 7), kernel: request_firmware() returns and the driver has the firmware
 	 image in fw_entry->{data,size}. If something went wrong
 	 request_firmware() returns non-zero and fw_entry is set to
 	 NULL.
 
- kernel(driver): Driver code calls release_firmware(fw_entry) releasing
+ 8), kernel(driver): Driver code calls release_firmware(fw_entry) releasing
 		 the firmware image and any related resource.
 
  High level behavior (driver code):

Documentation/zh_CN/IRQ.txt

@@ -0,0 +1,39 @@
+Chinese translated version of Documentation/IRQ.txt
+
+If you have any comment or update to the content, please contact the
+original document maintainer directly.  However, if you have a problem
+communicating in English you can also ask the Chinese maintainer for
+help.  Contact the Chinese maintainer if this translation is outdated
+or if there is a problem with the translation.
+
+Maintainer: Eric W. Biederman <ebiederman@xmission.com>
+Chinese maintainer: Fu Wei <tekkamanninja@gmail.com>
+---------------------------------------------------------------------
+Documentation/IRQ.txt 的中文翻译
+
+如果想评论或更新本文的内容，请直接联系原文档的维护者。如果你使用英文
+交流有困难的话，也可以向中文版维护者求助。如果本翻译更新不及时或者翻
+译存在问题，请联系中文版维护者。
+英文版维护者： Eric W. Biederman <ebiederman@xmission.com>
+中文版维护者： 傅炜 Fu Wei <tekkamanninja@gmail.com>
+中文版翻译者： 傅炜 Fu Wei <tekkamanninja@gmail.com>
+中文版校译者： 傅炜 Fu Wei <tekkamanninja@gmail.com>
+
+
+以下为正文
+---------------------------------------------------------------------
+何为 IRQ?
+
+一个 IRQ 是来自某个设备的一个中断请求。目前，它们可以来自一个硬件引脚，
+或来自一个数据包。多个设备可能连接到同个硬件引脚，从而共享一个 IRQ。
+
+一个 IRQ 编号是用于告知硬件中断源的内核标识。通常情况下，这是一个
+全局 irq_desc 数组的索引，但是除了在 linux/interrupt.h 中的实现，
+具体的细节是体系结构特定的。
+
+一个 IRQ 编号是设备上某个可能的中断源的枚举。通常情况下，枚举的编号是
+该引脚在系统内中断控制器的所有输入引脚中的编号。对于 ISA 总线中的情况，
+枚举的是在两个 i8259 中断控制器中 16 个输入引脚。
+
+架构可以对 IRQ 编号指定额外的含义，在硬件涉及任何手工配置的情况下，
+是被提倡的。ISA 的 IRQ 是一个分配这类额外含义的典型例子。

Documentation/zh_CN/arm64/booting.txt

@@ -0,0 +1,156 @@
+Chinese translated version of Documentation/arm64/booting.txt
+
+If you have any comment or update to the content, please contact the
+original document maintainer directly.  However, if you have a problem
+communicating in English you can also ask the Chinese maintainer for
+help.  Contact the Chinese maintainer if this translation is outdated
+or if there is a problem with the translation.
+
+Maintainer: Will Deacon <will.deacon@arm.com>
+Chinese maintainer: Fu Wei <tekkamanninja@gmail.com>
+---------------------------------------------------------------------
+Documentation/arm64/booting.txt 的中文翻译
+
+如果想评论或更新本文的内容，请直接联系原文档的维护者。如果你使用英文
+交流有困难的话，也可以向中文版维护者求助。如果本翻译更新不及时或者翻
+译存在问题，请联系中文版维护者。
+
+英文版维护者： Will Deacon <will.deacon@arm.com>
+中文版维护者： 傅炜  Fu Wei <tekkamanninja@gmail.com>
+中文版翻译者： 傅炜  Fu Wei <tekkamanninja@gmail.com>
+中文版校译者： 傅炜  Fu Wei <tekkamanninja@gmail.com>
+
+以下为正文
+---------------------------------------------------------------------
+			启动 AArch64 Linux
+			==================
+
+作者: Will Deacon <will.deacon@arm.com>
+日期: 2012 年 09 月 07 日
+
+本文档基于 Russell King 的 ARM 启动文档，且适用于所有公开发布的
+AArch64 Linux 内核代码。
+
+AArch64 异常模型由多个异常级别（EL0 - EL3）组成，对于 EL0 和 EL1
+异常级有对应的安全和非安全模式。EL2 是系统管理级，且仅存在于
+非安全模式下。EL3 是最高特权级，且仅存在于安全模式下。
+
+基于本文档的目的，我们将简单地使用‘引导装载程序’（‘boot loader’）
+这个术语来定义在将控制权交给 Linux 内核前 CPU 上执行的所有软件。
+这可能包含安全监控和系统管理代码，或者它可能只是一些用于准备最小启动
+环境的指令。
+
+基本上，引导装载程序（至少）应实现以下操作：
+
+1、设置和初始化 RAM
+2、设置设备树数据
+3、解压内核映像
+4、调用内核映像
+
+
+1、设置和初始化 RAM
+-----------------
+
+必要性: 强制
+
+引导装载程序应该找到并初始化系统中所有内核用于保持系统变量数据的 RAM。
+这个操作的执行是设备依赖的。（它可能使用内部算法来自动定位和计算所有
+RAM，或可能使用对这个设备已知的 RAM 信息，还可能使用任何引导装载程序
+设计者想到的匹配方法。）
+
+
+2、设置设备树数据
+---------------
+
+必要性: 强制
+
+设备树数据块（dtb）大小必须不大于 2 MB，且位于从内核映像起始算起第一个
+512MB 内的 2MB 边界上。这使得内核可以通过初始页表中的单个节描述符来
+映射此数据块。
+
+
+3、解压内核映像
+-------------
+
+必要性: 可选
+
+AArch64 内核当前没有提供自解压代码，因此如果使用了压缩内核映像文件
+（比如 Image.gz），则需要通过引导装载程序（使用 gzip 等）来进行解压。
+若引导装载程序没有实现这个需求，就要使用非压缩内核映像文件。
+
+
+4、调用内核映像
+-------------
+
+必要性: 强制
+
+已解压的内核映像包含一个 32 字节的头，内容如下：
+
+  u32 magic	= 0x14000008;	/* 跳转到 stext, 小端 */
+  u32 res0	= 0;		/* 保留 */
+  u64 text_offset;		/* 映像装载偏移 */
+  u64 res1	= 0;		/* 保留 */
+  u64 res2	= 0;		/* 保留 */
+
+映像必须位于系统 RAM 起始处的特定偏移（当前是 0x80000）。系统 RAM
+的起始地址必须是以 2MB 对齐的。
+
+在跳转入内核前，必须符合以下状态：
+
+- 停止所有 DMA 设备，这样内存数据就不会因为虚假网络包或磁盘数据而
+  被破坏。这可能可以节省你许多的调试时间。
+
+- 主 CPU 通用寄存器设置
+  x0 = 系统 RAM 中设备树数据块（dtb）的物理地址。
+  x1 = 0 (保留，将来可能使用)
+  x2 = 0 (保留，将来可能使用)
+  x3 = 0 (保留，将来可能使用)
+
+- CPU 模式
+  所有形式的中断必须在 PSTATE.DAIF 中被屏蔽（Debug、SError、IRQ
+  和 FIQ）。
+  CPU 必须处于 EL2（推荐，可访问虚拟化扩展）或非安全 EL1 模式下。
+
+- 高速缓存、MMU
+  MMU 必须关闭。
+  指令缓存开启或关闭都可以。
+  数据缓存必须关闭且无效。
+  外部高速缓存（如果存在）必须配置并禁用。
+
+- 架构计时器
+  CNTFRQ 必须设定为计时器的频率。
+  如果在 EL1 模式下进入内核，则 CNTHCTL_EL2 中的 EL1PCTEN (bit 0)
+  必须置位。
+
+- 一致性
+  通过内核启动的所有 CPU 在内核入口地址上必须处于相同的一致性域中。
+  这可能要根据具体实现来定义初始化过程，以使能每个CPU上对维护操作的
+  接收。
+
+- 系统寄存器
+  在进入内核映像的异常级中，所有构架中可写的系统寄存器必须通过软件
+  在一个更高的异常级别下初始化，以防止在 未知 状态下运行。
+
+引导装载程序必须在每个 CPU 处于以下状态时跳入内核入口：
+
+- 主 CPU 必须直接跳入内核映像的第一条指令。通过此 CPU 传递的设备树
+  数据块必须在每个 CPU 节点中包含以下内容：
+
+    1、‘enable-method’属性。目前，此字段支持的值仅为字符串“spin-table”。
+
+    2、‘cpu-release-addr’标识一个 64-bit、初始化为零的内存位置。
+
+  引导装载程序必须生成这些设备树属性，并在跳入内核入口之前将其插入
+  数据块。
+
+- 任何辅助 CPU 必须在内存保留区（通过设备树中的 /memreserve/ 域传递
+  给内核）中自旋于内核之外，轮询它们的 cpu-release-addr 位置（必须
+  包含在保留区中）。可通过插入 wfe 指令来降低忙循环开销，而主 CPU 将
+  发出 sev 指令。当对 cpu-release-addr 所指位置的读取操作返回非零值
+  时，CPU 必须直接跳入此值所指向的地址。
+
+- 辅助 CPU 通用寄存器设置
+  x0 = 0 (保留，将来可能使用)
+  x1 = 0 (保留，将来可能使用)
+  x2 = 0 (保留，将来可能使用)
+  x3 = 0 (保留，将来可能使用)

Documentation/zh_CN/arm64/memory.txt

@@ -0,0 +1,93 @@
+Chinese translated version of Documentation/arm64/memory.txt
+
+If you have any comment or update to the content, please contact the
+original document maintainer directly.  However, if you have a problem
+communicating in English you can also ask the Chinese maintainer for
+help.  Contact the Chinese maintainer if this translation is outdated
+or if there is a problem with the translation.
+
+Maintainer: Catalin Marinas <catalin.marinas@arm.com>
+Chinese maintainer: Fu Wei <tekkamanninja@gmail.com>
+---------------------------------------------------------------------
+Documentation/arm64/memory.txt 的中文翻译
+
+如果想评论或更新本文的内容，请直接联系原文档的维护者。如果你使用英文
+交流有困难的话，也可以向中文版维护者求助。如果本翻译更新不及时或者翻
+译存在问题，请联系中文版维护者。
+
+英文版维护者： Catalin Marinas <catalin.marinas@arm.com>
+中文版维护者： 傅炜  Fu Wei <tekkamanninja@gmail.com>
+中文版翻译者： 傅炜  Fu Wei <tekkamanninja@gmail.com>
+中文版校译者： 傅炜  Fu Wei <tekkamanninja@gmail.com>
+
+以下为正文
+---------------------------------------------------------------------
+		     Linux 在 AArch64 中的内存布局
+		     ===========================
+
+作者: Catalin Marinas <catalin.marinas@arm.com>
+日期: 2012 年 02 月 20 日
+
+本文档描述 AArch64 Linux 内核所使用的虚拟内存布局。此构架可以实现
+页大小为 4KB 的 4 级转换表和页大小为 64KB 的 3 级转换表。
+
+AArch64 Linux 使用页大小为 4KB 的 3 级转换表配置，对于用户和内核
+都有 39-bit (512GB) 的虚拟地址空间。对于页大小为 64KB的配置，仅
+使用 2 级转换表，但内存布局相同。
+
+用户地址空间的 63:39 位为 0，而内核地址空间的相应位为 1。TTBRx 的
+选择由虚拟地址的 63 位给出。swapper_pg_dir 仅包含内核（全局）映射，
+而用户 pgd 仅包含用户（非全局）映射。swapper_pgd_dir 地址被写入
+TTBR1 中，且从不写入 TTBR0。
+
+
+AArch64 Linux 内存布局：
+
+起始地址			结束地址			大小		用途
+-----------------------------------------------------------------------
+0000000000000000	0000007fffffffff	 512GB		用户空间
+
+ffffff8000000000	ffffffbbfffcffff	~240GB		vmalloc
+
+ffffffbbfffd0000	ffffffbcfffdffff	  64KB		[防护页]
+
+ffffffbbfffe0000	ffffffbcfffeffff	  64KB		PCI I/O 空间
+
+ffffffbbffff0000	ffffffbcffffffff	  64KB		[防护页]
+
+ffffffbc00000000	ffffffbdffffffff	   8GB		vmemmap
+
+ffffffbe00000000	ffffffbffbffffff	  ~8GB		[防护页，未来用于 vmmemap]
+
+ffffffbffc000000	ffffffbfffffffff	  64MB		模块
+
+ffffffc000000000	ffffffffffffffff	 256GB		内存空间
+
+
+4KB 页大小的转换表查找：
+
++--------+--------+--------+--------+--------+--------+--------+--------+
+|63    56|55    48|47    40|39    32|31    24|23    16|15     8|7      0|
++--------+--------+--------+--------+--------+--------+--------+--------+
+ |                 |         |         |         |         |
+ |                 |         |         |         |         v
+ |                 |         |         |         |   [11:0]  页内偏移
+ |                 |         |         |         +-> [20:12] L3 索引
+ |                 |         |         +-----------> [29:21] L2 索引
+ |                 |         +---------------------> [38:30] L1 索引
+ |                 +-------------------------------> [47:39] L0 索引 (未使用)
+ +-------------------------------------------------> [63] TTBR0/1
+
+
+64KB 页大小的转换表查找：
+
++--------+--------+--------+--------+--------+--------+--------+--------+
+|63    56|55    48|47    40|39    32|31    24|23    16|15     8|7      0|
++--------+--------+--------+--------+--------+--------+--------+--------+
+ |                 |    |               |              |
+ |                 |    |               |              v
+ |                 |    |               |            [15:0]  页内偏移
+ |                 |    |               +----------> [28:16] L3 索引
+ |                 |    +--------------------------> [41:29] L2 索引 (仅使用 38:29 )
+ |                 +-------------------------------> [47:42] L1 索引 (未使用)
+ +-------------------------------------------------> [63] TTBR0/1

MAINTAINERS

@@ -637,6 +637,13 @@ W:	http://www.arm.linux.org.uk/
 S:	Maintained
 F:	arch/arm/
 
+ARM SUB-ARCHITECTURES
+L:	linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
+S:	MAINTAINED
+F:	arch/arm/mach-*/
+F:	arch/arm/plat-*/
+T:	git git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc.git
+
 ARM PRIMECELL AACI PL041 DRIVER
 M:	Russell King <linux@arm.linux.org.uk>
 S:	Maintained
@@ -2802,6 +2809,7 @@ F:	sound/usb/misc/ua101.c
 EXTENSIBLE FIRMWARE INTERFACE (EFI)
 M:	Matt Fleming <matt.fleming@intel.com>
 L:	linux-efi@vger.kernel.org
+T:	git git://git.kernel.org/pub/scm/linux/kernel/git/mfleming/efi.git
 S:	Maintained
 F:	Documentation/x86/efi-stub.txt
 F:	arch/ia64/kernel/efi.c
@@ -5061,7 +5069,13 @@ T:	git git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next.git
 S:	Odd Fixes
 F:	drivers/net/
 F:	include/linux/if_*
-F:	include/linux/*device.h
+F:	include/linux/netdevice.h
+F:	include/linux/arcdevice.h
+F:	include/linux/etherdevice.h
+F:	include/linux/fcdevice.h
+F:	include/linux/fddidevice.h
+F:	include/linux/hippidevice.h
+F:	include/linux/inetdevice.h
 
 NETXEN (1/10) GbE SUPPORT
 M:	Sony Chacko <sony.chacko@qlogic.com>

Makefile

@@ -1,7 +1,7 @@
 VERSION = 3
 PATCHLEVEL = 7
 SUBLEVEL = 0
-EXTRAVERSION = -rc2
+EXTRAVERSION = -rc3
 NAME = Terrified Chipmunk
 
 # *DOCUMENTATION*

arch/alpha/include/asm/thread_info.h

@@ -7,6 +7,7 @@
 #include <asm/processor.h>
 #include <asm/types.h>
 #include <asm/hwrpb.h>
+#include <asm/sysinfo.h>
 #endif
 
 #ifndef __ASSEMBLY__
@@ -21,6 +22,7 @@ struct thread_info {
 	mm_segment_t		addr_limit;	/* thread address space */
 	unsigned		cpu;		/* current CPU */
 	int			preempt_count; /* 0 => preemptable, <0 => BUG */
+	unsigned int		status;		/* thread-synchronous flags */
 
 	int bpt_nsaved;
 	unsigned long bpt_addr[2];		/* breakpoint handling  */
@@ -63,8 +65,6 @@ register struct thread_info *__current_thread_info __asm__("$8");
  * - these are process state flags and used from assembly
  * - pending work-to-be-done flags come first and must be assigned to be
  *   within bits 0 to 7 to fit in and immediate operand.
- * - ALPHA_UAC_SHIFT below must be kept consistent with the unaligned
- *   control flags.
  *
  * TIF_SYSCALL_TRACE is known to be 0 via blbs.
  */
@@ -72,18 +72,12 @@ register struct thread_info *__current_thread_info __asm__("$8");
 #define TIF_NOTIFY_RESUME	1	/* callback before returning to user */
 #define TIF_SIGPENDING		2	/* signal pending */
 #define TIF_NEED_RESCHED	3	/* rescheduling necessary */
-#define TIF_POLLING_NRFLAG	8	/* poll_idle is polling NEED_RESCHED */
 #define TIF_DIE_IF_KERNEL	9	/* dik recursion lock */
-#define TIF_UAC_NOPRINT		10	/* ! Preserve sequence of following */
-#define TIF_UAC_NOFIX		11	/* ! flags as they match            */
-#define TIF_UAC_SIGBUS		12	/* ! userspace part of 'osf_sysinfo' */
 #define TIF_MEMDIE		13	/* is terminating due to OOM killer */
-#define TIF_RESTORE_SIGMASK	14	/* restore signal mask in do_signal */
 
 #define _TIF_SYSCALL_TRACE	(1<<TIF_SYSCALL_TRACE)
 #define _TIF_SIGPENDING		(1<<TIF_SIGPENDING)
 #define _TIF_NEED_RESCHED	(1<<TIF_NEED_RESCHED)
-#define _TIF_POLLING_NRFLAG	(1<<TIF_POLLING_NRFLAG)
 #define _TIF_NOTIFY_RESUME	(1<<TIF_NOTIFY_RESUME)
 
 /* Work to do on interrupt/exception return.  */
@@ -94,29 +88,63 @@ register struct thread_info *__current_thread_info __asm__("$8");
 #define _TIF_ALLWORK_MASK	(_TIF_WORK_MASK		\
 				 | _TIF_SYSCALL_TRACE)
 
-#define ALPHA_UAC_SHIFT		TIF_UAC_NOPRINT
+#define TS_UAC_NOPRINT		0x0001	/* ! Preserve the following three */
-#define ALPHA_UAC_MASK		(1 << TIF_UAC_NOPRINT | 1 << TIF_UAC_NOFIX | \
+#define TS_UAC_NOFIX		0x0002	/* ! flags as they match          */
-				 1 << TIF_UAC_SIGBUS)
+#define TS_UAC_SIGBUS		0x0004	/* ! userspace part of 'osf_sysinfo' */
+#define TS_RESTORE_SIGMASK	0x0008	/* restore signal mask in do_signal() */
+#define TS_POLLING		0x0010	/* idle task polling need_resched,
+					   skip sending interrupt */
 
-#define SET_UNALIGN_CTL(task,value)	({				     \
+#define tsk_is_polling(t) (task_thread_info(t)->status & TS_POLLING)
-	task_thread_info(task)->flags = ((task_thread_info(task)->flags &    \
+
-		~ALPHA_UAC_MASK)					     \
+#ifndef __ASSEMBLY__
-		| (((value) << ALPHA_UAC_SHIFT)       & (1<<TIF_UAC_NOPRINT))\
+#define HAVE_SET_RESTORE_SIGMASK	1
-		| (((value) << (ALPHA_UAC_SHIFT + 1)) & (1<<TIF_UAC_SIGBUS)) \
+static inline void set_restore_sigmask(void)
-		| (((value) << (ALPHA_UAC_SHIFT - 1)) & (1<<TIF_UAC_NOFIX)));\
+{
+	struct thread_info *ti = current_thread_info();
+	ti->status |= TS_RESTORE_SIGMASK;
+	WARN_ON(!test_bit(TIF_SIGPENDING, (unsigned long *)&ti->flags));
+}
+static inline void clear_restore_sigmask(void)
+{
+	current_thread_info()->status &= ~TS_RESTORE_SIGMASK;
+}
+static inline bool test_restore_sigmask(void)
+{
+	return current_thread_info()->status & TS_RESTORE_SIGMASK;
+}
+static inline bool test_and_clear_restore_sigmask(void)
+{
+	struct thread_info *ti = current_thread_info();
+	if (!(ti->status & TS_RESTORE_SIGMASK))
+		return false;
+	ti->status &= ~TS_RESTORE_SIGMASK;
+	return true;
+}
+#endif
+
+#define SET_UNALIGN_CTL(task,value)	({				\
+	__u32 status = task_thread_info(task)->status & ~UAC_BITMASK;	\
+	if (value & PR_UNALIGN_NOPRINT)					\
+		status |= TS_UAC_NOPRINT;				\
+	if (value & PR_UNALIGN_SIGBUS)					\
+		status |= TS_UAC_SIGBUS;				\
+	if (value & 4)	/* alpha-specific */				\
+		status |= TS_UAC_NOFIX;					\
+	task_thread_info(task)->status = status;			\
 	0; })
 
 #define GET_UNALIGN_CTL(task,value)	({				\
-	put_user((task_thread_info(task)->flags & (1 << TIF_UAC_NOPRINT))\
+	__u32 status = task_thread_info(task)->status & ~UAC_BITMASK;	\
-		  >> ALPHA_UAC_SHIFT					\
+	__u32 res = 0;							\
-		 | (task_thread_info(task)->flags & (1 << TIF_UAC_SIGBUS))\
+	if (status & TS_UAC_NOPRINT)					\
-		 >> (ALPHA_UAC_SHIFT + 1)				\
+		res |= PR_UNALIGN_NOPRINT;				\
-		 | (task_thread_info(task)->flags & (1 << TIF_UAC_NOFIX))\
+	if (status & TS_UAC_SIGBUS)					\
-		 >> (ALPHA_UAC_SHIFT - 1),				\
+		res |= PR_UNALIGN_SIGBUS;				\
-		 (int __user *)(value));				\
+	if (status & TS_UAC_NOFIX)					\
+		res |= 4;						\
+	put_user(res, (int __user *)(value));				\
 	})
 
-#define tsk_is_polling(t) test_tsk_thread_flag(t, TIF_POLLING_NRFLAG)
-
 #endif /* __KERNEL__ */
 #endif /* _ALPHA_THREAD_INFO_H */

arch/alpha/kernel/osf_sys.c

@@ -793,8 +793,7 @@ SYSCALL_DEFINE5(osf_getsysinfo, unsigned long, op, void __user *, buffer,
  	case GSI_UACPROC:
 		if (nbytes < sizeof(unsigned int))
 			return -EINVAL;
-		w = (current_thread_info()->flags >> ALPHA_UAC_SHIFT) &
+		w = current_thread_info()->status & UAC_BITMASK;
-			UAC_BITMASK;
 		if (put_user(w, (unsigned int __user *)buffer))
 			return -EFAULT;
  		return 1;
@@ -904,24 +903,20 @@ SYSCALL_DEFINE5(osf_setsysinfo, unsigned long, op, void __user *, buffer,
 		break;
 
  	case SSI_NVPAIRS: {
-		unsigned long v, w, i;
+		unsigned __user *p = buffer;
-		unsigned int old, new;
+		unsigned i;
 		
- 		for (i = 0; i < nbytes; ++i) {
+		for (i = 0, p = buffer; i < nbytes; ++i, p += 2) {
+			unsigned v, w, status;
 
- 			if (get_user(v, 2*i + (unsigned int __user *)buffer))
+			if (get_user(v, p) || get_user(w, p + 1))
- 				return -EFAULT;
- 			if (get_user(w, 2*i + 1 + (unsigned int __user *)buffer))
  				return -EFAULT;
  			switch (v) {
  			case SSIN_UACPROC:
-			again:
+				w &= UAC_BITMASK;
-				old = current_thread_info()->flags;
+				status = current_thread_info()->status;
-				new = old & ~(UAC_BITMASK << ALPHA_UAC_SHIFT);
+				status = (status & ~UAC_BITMASK) | w;
-				new = new | (w & UAC_BITMASK) << ALPHA_UAC_SHIFT;
+				current_thread_info()->status = status;
-				if (cmpxchg(&current_thread_info()->flags,
-					    old, new) != old)
-					goto again;
  				break;
  
  			default:

arch/alpha/kernel/process.c

@@ -49,7 +49,7 @@ EXPORT_SYMBOL(pm_power_off);
 void
 cpu_idle(void)
 {
-	set_thread_flag(TIF_POLLING_NRFLAG);
+	current_thread_info()->status |= TS_POLLING;
 
 	while (1) {
 		/* FIXME -- EV6 and LCA45 know how to power down

arch/alpha/kernel/traps.c

@@ -780,17 +780,17 @@ do_entUnaUser(void __user * va, unsigned long opcode,
 	/* Check the UAC bits to decide what the user wants us to do
 	   with the unaliged access.  */
 
-	if (!test_thread_flag (TIF_UAC_NOPRINT)) {
+	if (!(current_thread_info()->status & TS_UAC_NOPRINT)) {
 		if (__ratelimit(&ratelimit)) {
 			printk("%s(%d): unaligned trap at %016lx: %p %lx %ld\n",
 			       current->comm, task_pid_nr(current),
 			       regs->pc - 4, va, opcode, reg);
 		}
 	}
-	if (test_thread_flag (TIF_UAC_SIGBUS))
+	if ((current_thread_info()->status & TS_UAC_SIGBUS))
 		goto give_sigbus;
 	/* Not sure why you'd want to use this, but... */
-	if (test_thread_flag (TIF_UAC_NOFIX))
+	if ((current_thread_info()->status & TS_UAC_NOFIX))
 		return;
 
 	/* Don't bother reading ds in the access check since we already

arch/arm/Kconfig

@@ -1603,8 +1603,8 @@ config NR_CPUS
 	default "4"
 
 config HOTPLUG_CPU
-	bool "Support for hot-pluggable CPUs (EXPERIMENTAL)"
+	bool "Support for hot-pluggable CPUs"
-	depends on SMP && HOTPLUG && EXPERIMENTAL
+	depends on SMP && HOTPLUG
 	help
 	  Say Y here to experiment with turning CPUs off and on.  CPUs
 	  can be controlled through /sys/devices/system/cpu.
@@ -1645,8 +1645,8 @@ config HZ
 	default 100
 
 config THUMB2_KERNEL
-	bool "Compile the kernel in Thumb-2 mode (EXPERIMENTAL)"
+	bool "Compile the kernel in Thumb-2 mode"
-	depends on CPU_V7 && !CPU_V6 && !CPU_V6K && EXPERIMENTAL
+	depends on CPU_V7 && !CPU_V6 && !CPU_V6K
 	select AEABI
 	select ARM_ASM_UNIFIED
 	select ARM_UNWIND
@@ -1850,6 +1850,7 @@ config XEN_DOM0
 config XEN
 	bool "Xen guest support on ARM (EXPERIMENTAL)"
 	depends on EXPERIMENTAL && ARM && OF
+	depends on CPU_V7 && !CPU_V6
 	help
 	  Say Y if you want to run Linux in a Virtual Machine on Xen on ARM.
 

arch/arm/Makefile

@@ -21,8 +21,6 @@ endif
 OBJCOPYFLAGS	:=-O binary -R .comment -S
 GZFLAGS		:=-9
 #KBUILD_CFLAGS	+=-pipe
-# Explicitly specifiy 32-bit ARM ISA since toolchain default can be -mthumb:
-KBUILD_CFLAGS	+=$(call cc-option,-marm,)
 
 # Never generate .eh_frame
 KBUILD_CFLAGS	+= $(call cc-option,-fno-dwarf2-cfi-asm)
@@ -105,17 +103,20 @@ endif
 ifeq ($(CONFIG_THUMB2_KERNEL),y)
 AFLAGS_AUTOIT	:=$(call as-option,-Wa$(comma)-mimplicit-it=always,-Wa$(comma)-mauto-it)
 AFLAGS_NOWARN	:=$(call as-option,-Wa$(comma)-mno-warn-deprecated,-Wa$(comma)-W)
-CFLAGS_THUMB2	:=-mthumb $(AFLAGS_AUTOIT) $(AFLAGS_NOWARN)
+CFLAGS_ISA	:=-mthumb $(AFLAGS_AUTOIT) $(AFLAGS_NOWARN)
-AFLAGS_THUMB2	:=$(CFLAGS_THUMB2) -Wa$(comma)-mthumb
+AFLAGS_ISA	:=$(CFLAGS_ISA) -Wa$(comma)-mthumb
 # Work around buggy relocation from gas if requested:
 ifeq ($(CONFIG_THUMB2_AVOID_R_ARM_THM_JUMP11),y)
 CFLAGS_MODULE	+=-fno-optimize-sibling-calls
 endif
+else
+CFLAGS_ISA	:=$(call cc-option,-marm,)
+AFLAGS_ISA	:=$(CFLAGS_ISA)
 endif
 
 # Need -Uarm for gcc < 3.x
-KBUILD_CFLAGS	+=$(CFLAGS_ABI) $(CFLAGS_THUMB2) $(arch-y) $(tune-y) $(call cc-option,-mshort-load-bytes,$(call cc-option,-malignment-traps,)) -msoft-float -Uarm
+KBUILD_CFLAGS	+=$(CFLAGS_ABI) $(CFLAGS_ISA) $(arch-y) $(tune-y) $(call cc-option,-mshort-load-bytes,$(call cc-option,-malignment-traps,)) -msoft-float -Uarm
-KBUILD_AFLAGS	+=$(CFLAGS_ABI) $(AFLAGS_THUMB2) $(arch-y) $(tune-y) -include asm/unified.h -msoft-float
+KBUILD_AFLAGS	+=$(CFLAGS_ABI) $(AFLAGS_ISA) $(arch-y) $(tune-y) -include asm/unified.h -msoft-float
 
 CHECKFLAGS	+= -D__arm__
 

arch/arm/boot/Makefile

@@ -33,7 +33,7 @@ ifeq ($(CONFIG_XIP_KERNEL),y)
 
 $(obj)/xipImage: vmlinux FORCE
 	$(call if_changed,objcopy)
-	@echo '  Kernel: $@ is ready (physical address: $(CONFIG_XIP_PHYS_ADDR))'
+	$(kecho) '  Kernel: $@ is ready (physical address: $(CONFIG_XIP_PHYS_ADDR))'
 
 $(obj)/Image $(obj)/zImage: FORCE
 	@echo 'Kernel configured for XIP (CONFIG_XIP_KERNEL=y)'
@@ -48,14 +48,14 @@ $(obj)/xipImage: FORCE
 
 $(obj)/Image: vmlinux FORCE
 	$(call if_changed,objcopy)
-	@echo '  Kernel: $@ is ready'
+	$(kecho) '  Kernel: $@ is ready'
 
 $(obj)/compressed/vmlinux: $(obj)/Image FORCE
 	$(Q)$(MAKE) $(build)=$(obj)/compressed $@
 
 $(obj)/zImage:	$(obj)/compressed/vmlinux FORCE
 	$(call if_changed,objcopy)
-	@echo '  Kernel: $@ is ready'
+	$(kecho) '  Kernel: $@ is ready'
 
 endif
 
@@ -90,7 +90,7 @@ fi
 $(obj)/uImage:	$(obj)/zImage FORCE
 	@$(check_for_multiple_loadaddr)
 	$(call if_changed,uimage)
-	@echo '  Image $@ is ready'
+	$(kecho) '  Image $@ is ready'
 
 $(obj)/bootp/bootp: $(obj)/zImage initrd FORCE
 	$(Q)$(MAKE) $(build)=$(obj)/bootp $@
@@ -98,7 +98,7 @@ $(obj)/bootp/bootp: $(obj)/zImage initrd FORCE
 
 $(obj)/bootpImage: $(obj)/bootp/bootp FORCE
 	$(call if_changed,objcopy)
-	@echo '  Kernel: $@ is ready'
+	$(kecho) '  Kernel: $@ is ready'
 
 PHONY += initrd FORCE
 initrd:

arch/arm/boot/dts/at91sam9g20ek_common.dtsi

@@ -126,14 +126,14 @@
 		#size-cells = <0>;
 
 		btn3 {
-			label = "Buttin 3";
+			label = "Button 3";
 			gpios = <&pioA 30 1>;
 			linux,code = <0x103>;
 			gpio-key,wakeup;
 		};
 
 		btn4 {
-			label = "Buttin 4";
+			label = "Button 4";
 			gpios = <&pioA 31 1>;
 			linux,code = <0x104>;
 			gpio-key,wakeup;

arch/arm/boot/dts/dbx5x0.dtsi

@@ -483,6 +483,8 @@
 			compatible = "stericsson,db8500-i2c", "st,nomadik-i2c", "arm,primecell";
 			reg = <0x80004000 0x1000>;
 			interrupts = <0 21 0x4>;
+			arm,primecell-periphid = <0x180024>;
+
 			#address-cells = <1>;
 			#size-cells = <0>;
 			v-i2c-supply = <&db8500_vape_reg>;
@@ -494,6 +496,8 @@
 			compatible = "stericsson,db8500-i2c", "st,nomadik-i2c", "arm,primecell";
 			reg = <0x80122000 0x1000>;
 			interrupts = <0 22 0x4>;
+			arm,primecell-periphid = <0x180024>;
+
 			#address-cells = <1>;
 			#size-cells = <0>;
 			v-i2c-supply = <&db8500_vape_reg>;
@@ -505,6 +509,8 @@
 			compatible = "stericsson,db8500-i2c", "st,nomadik-i2c", "arm,primecell";
 			reg = <0x80128000 0x1000>;
 			interrupts = <0 55 0x4>;
+			arm,primecell-periphid = <0x180024>;
+
 			#address-cells = <1>;
 			#size-cells = <0>;
 			v-i2c-supply = <&db8500_vape_reg>;
@@ -516,6 +522,8 @@
 			compatible = "stericsson,db8500-i2c", "st,nomadik-i2c", "arm,primecell";
 			reg = <0x80110000 0x1000>;
 			interrupts = <0 12 0x4>;
+			arm,primecell-periphid = <0x180024>;
+
 			#address-cells = <1>;
 			#size-cells = <0>;
 			v-i2c-supply = <&db8500_vape_reg>;
@@ -527,6 +535,8 @@
 			compatible = "stericsson,db8500-i2c", "st,nomadik-i2c", "arm,primecell";
 			reg = <0x8012a000 0x1000>;
 			interrupts = <0 51 0x4>;
+			arm,primecell-periphid = <0x180024>;
+
 			#address-cells = <1>;
 			#size-cells = <0>;
 			v-i2c-supply = <&db8500_vape_reg>;
@@ -573,33 +583,38 @@
 			interrupts = <0 60 0x4>;
 			status = "disabled";
 		};
+
 		sdi@80118000 {
 			compatible = "arm,pl18x", "arm,primecell";
 			reg = <0x80118000 0x1000>;
 			interrupts = <0 50 0x4>;
 			status = "disabled";
 		};
+
 		sdi@80005000 {
 			compatible = "arm,pl18x", "arm,primecell";
 			reg = <0x80005000 0x1000>;
 			interrupts = <0 41 0x4>;
 			status = "disabled";
 		};
+
 		sdi@80119000 {
 			compatible = "arm,pl18x", "arm,primecell";
 			reg = <0x80119000 0x1000>;
 			interrupts = <0 59 0x4>;
 			status = "disabled";
 		};
+
 		sdi@80114000 {
 			compatible = "arm,pl18x", "arm,primecell";
 			reg = <0x80114000 0x1000>;
 			interrupts = <0 99 0x4>;
 			status = "disabled";
 		};
+
 		sdi@80008000 {
 			compatible = "arm,pl18x", "arm,primecell";
-			reg = <0x80114000 0x1000>;
+			reg = <0x80008000 0x1000>;
 			interrupts = <0 100 0x4>;
 			status = "disabled";
 		};

arch/arm/boot/dts/exynos4210-trats.dts

@@ -20,8 +20,10 @@
 	compatible = "samsung,trats", "samsung,exynos4210";
 
 	memory {
-		reg =  <0x40000000 0x20000000
+		reg =  <0x40000000 0x10000000
-			0x60000000 0x20000000>;
+			0x50000000 0x10000000
+			0x60000000 0x10000000
+			0x70000000 0x10000000>;
 	};
 
 	chosen {

arch/arm/boot/dts/imx23.dtsi

@@ -69,6 +69,7 @@
 				interrupts = <13>, <56>;
 				interrupt-names = "gpmi-dma", "bch";
 				clocks = <&clks 34>;
+				clock-names = "gpmi_io";
 				fsl,gpmi-dma-channel = <4>;
 				status = "disabled";
 			};

arch/arm/boot/dts/imx28.dtsi

@@ -85,6 +85,7 @@
 				interrupts = <88>, <41>;
 				interrupt-names = "gpmi-dma", "bch";
 				clocks = <&clks 50>;
+				clock-names = "gpmi_io";
 				fsl,gpmi-dma-channel = <4>;
 				status = "disabled";
 			};

arch/arm/boot/dts/omap3.dtsi

@@ -257,7 +257,7 @@
 			interrupt-names = "common", "tx", "rx", "sidetone";
 			interrupt-parent = <&intc>;
 			ti,buffer-size = <1280>;
-			ti,hwmods = "mcbsp2";
+			ti,hwmods = "mcbsp2", "mcbsp2_sidetone";
 		};
 
 		mcbsp3: mcbsp@49024000 {
@@ -272,7 +272,7 @@
 			interrupt-names = "common", "tx", "rx", "sidetone";
 			interrupt-parent = <&intc>;
 			ti,buffer-size = <128>;
-			ti,hwmods = "mcbsp3";
+			ti,hwmods = "mcbsp3", "mcbsp3_sidetone";
 		};
 
 		mcbsp4: mcbsp@49026000 {

arch/arm/configs/imx_v6_v7_defconfig

@@ -139,6 +139,7 @@ CONFIG_I2C_IMX=y
 CONFIG_SPI=y
 CONFIG_SPI_IMX=y
 CONFIG_GPIO_SYSFS=y
+CONFIG_GPIO_MC9S08DZ60=y
 # CONFIG_HWMON is not set
 CONFIG_WATCHDOG=y
 CONFIG_IMX2_WDT=y
@@ -155,6 +156,7 @@ CONFIG_SOC_CAMERA=y
 CONFIG_SOC_CAMERA_OV2640=y
 CONFIG_VIDEO_MX3=y
 CONFIG_FB=y
+CONFIG_LCD_PLATFORM=y
 CONFIG_BACKLIGHT_LCD_SUPPORT=y
 CONFIG_LCD_CLASS_DEVICE=y
 CONFIG_LCD_L4F00242T03=y

arch/arm/configs/mvebu_defconfig

@@ -1,6 +1,6 @@
 CONFIG_EXPERIMENTAL=y
 CONFIG_SYSVIPC=y
-CONFIG_NO_HZ=y
+CONFIG_IRQ_DOMAIN_DEBUG=y
 CONFIG_HIGH_RES_TIMERS=y
 CONFIG_LOG_BUF_SHIFT=14
 CONFIG_BLK_DEV_INITRD=y
@@ -9,10 +9,12 @@ CONFIG_SLAB=y
 CONFIG_MODULES=y
 CONFIG_MODULE_UNLOAD=y
 CONFIG_ARCH_MVEBU=y
-CONFIG_MACH_ARMADA_370_XP=y
+CONFIG_MACH_ARMADA_370=y
+CONFIG_MACH_ARMADA_XP=y
+# CONFIG_CACHE_L2X0 is not set
 CONFIG_AEABI=y
 CONFIG_HIGHMEM=y
-CONFIG_USE_OF=y
+# CONFIG_COMPACTION is not set
 CONFIG_ZBOOT_ROM_TEXT=0x0
 CONFIG_ZBOOT_ROM_BSS=0x0
 CONFIG_ARM_APPENDED_DTB=y
@@ -23,6 +25,8 @@ CONFIG_SERIAL_8250_CONSOLE=y
 CONFIG_SERIAL_OF_PLATFORM=y
 CONFIG_GPIOLIB=y
 CONFIG_GPIO_SYSFS=y
+# CONFIG_USB_SUPPORT is not set
+# CONFIG_IOMMU_SUPPORT is not set
 CONFIG_EXT2_FS=y
 CONFIG_EXT3_FS=y
 # CONFIG_EXT3_FS_XATTR is not set

arch/arm/configs/versatile_defconfig

@@ -1,3 +1,4 @@
+CONFIG_ARCH_VERSATILE=y
 CONFIG_EXPERIMENTAL=y
 # CONFIG_LOCALVERSION_AUTO is not set
 CONFIG_SYSVIPC=y

arch/arm/include/asm/flat.h

@@ -8,7 +8,7 @@
 #define	flat_argvp_envp_on_stack()		1
 #define	flat_old_ram_flag(flags)		(flags)
 #define	flat_reloc_valid(reloc, size)		((reloc) <= (size))
-#define	flat_get_addr_from_rp(rp, relval, flags, persistent) get_unaligned(rp)
+#define	flat_get_addr_from_rp(rp, relval, flags, persistent) ((void)persistent,get_unaligned(rp))
 #define	flat_put_addr_at_rp(rp, val, relval)	put_unaligned(val,rp)
 #define	flat_get_relocate_addr(rel)		(rel)
 #define	flat_set_persistent(relval, p)		0

arch/arm/include/asm/uaccess.h

@@ -200,8 +200,8 @@ extern int __put_user_8(void *, unsigned long long);
 #define USER_DS			KERNEL_DS
 
 #define segment_eq(a,b)		(1)
-#define __addr_ok(addr)		(1)
+#define __addr_ok(addr)		((void)(addr),1)
-#define __range_ok(addr,size)	(0)
+#define __range_ok(addr,size)	((void)(addr),0)
 #define get_fs()		(KERNEL_DS)
 
 static inline void set_fs(mm_segment_t fs)

arch/arm/include/asm/xen/interface.h

@@ -29,16 +29,22 @@
 
 #ifndef __ASSEMBLY__
 /* Explicitly size integers that represent pfns in the interface with
- * Xen so that we can have one ABI that works for 32 and 64 bit guests. */
+ * Xen so that we can have one ABI that works for 32 and 64 bit guests.
+ * Note that this means that the xen_pfn_t type may be capable of
+ * representing pfn's which the guest cannot represent in its own pfn
+ * type. However since pfn space is controlled by the guest this is
+ * fine since it simply wouldn't be able to create any sure pfns in
+ * the first place.
+ */
 typedef uint64_t xen_pfn_t;
+#define PRI_xen_pfn "llx"
 typedef uint64_t xen_ulong_t;
+#define PRI_xen_ulong "llx"
 /* Guest handles for primitive C types. */
 __DEFINE_GUEST_HANDLE(uchar, unsigned char);
 __DEFINE_GUEST_HANDLE(uint,  unsigned int);
-__DEFINE_GUEST_HANDLE(ulong, unsigned long);
 DEFINE_GUEST_HANDLE(char);
 DEFINE_GUEST_HANDLE(int);
-DEFINE_GUEST_HANDLE(long);
 DEFINE_GUEST_HANDLE(void);
 DEFINE_GUEST_HANDLE(uint64_t);
 DEFINE_GUEST_HANDLE(uint32_t);

arch/arm/include/asm/xen/page.h

@@ -10,7 +10,7 @@
 #include <xen/interface/grant_table.h>
 
 #define pfn_to_mfn(pfn)			(pfn)
-#define phys_to_machine_mapping_valid	(1)
+#define phys_to_machine_mapping_valid(pfn) (1)
 #define mfn_to_pfn(mfn)			(mfn)
 #define mfn_to_virt(m)			(__va(mfn_to_pfn(m) << PAGE_SHIFT))
 
@@ -30,6 +30,8 @@ typedef struct xpaddr {
 #define XMADDR(x)	((xmaddr_t) { .maddr = (x) })
 #define XPADDR(x)	((xpaddr_t) { .paddr = (x) })
 
+#define INVALID_P2M_ENTRY      (~0UL)
+
 static inline xmaddr_t phys_to_machine(xpaddr_t phys)
 {
 	unsigned offset = phys.paddr & ~PAGE_MASK;
@@ -74,9 +76,14 @@ static inline int m2p_remove_override(struct page *page, bool clear_pte)
 	return 0;
 }
 
+static inline bool __set_phys_to_machine(unsigned long pfn, unsigned long mfn)
+{
+	BUG_ON(pfn != mfn && mfn != INVALID_P2M_ENTRY);
+	return true;
+}
+
 static inline bool set_phys_to_machine(unsigned long pfn, unsigned long mfn)
 {
-	BUG();
+	return __set_phys_to_machine(pfn, mfn);
-	return false;
 }
 #endif /* _ASM_ARM_XEN_PAGE_H */

arch/arm/include/debug/8250_32.S

@@ -0,0 +1,27 @@
+/*
+ * Copyright (c) 2011 Picochip Ltd., Jamie Iles
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ * Derived from arch/arm/mach-davinci/include/mach/debug-macro.S to use 32-bit
+ * accesses to the 8250.
+ */
+
+#include <linux/serial_reg.h>
+
+		.macro	senduart,rd,rx
+		str	\rd, [\rx, #UART_TX << UART_SHIFT]
+		.endm
+
+		.macro	busyuart,rd,rx
+1002:		ldr	\rd, [\rx, #UART_LSR << UART_SHIFT]
+		and	\rd, \rd, #UART_LSR_TEMT | UART_LSR_THRE
+		teq	\rd, #UART_LSR_TEMT | UART_LSR_THRE
+		bne	1002b
+		.endm
+
+		/* The UART's don't have any flow control IO's wired up. */
+		.macro	waituart,rd,rx
+		.endm

arch/arm/include/debug/picoxcell.S

@@ -5,10 +5,7 @@
  * it under the terms of the GNU General Public License version 2 as
  * published by the Free Software Foundation.
  *
- * Derived from arch/arm/mach-davinci/include/mach/debug-macro.S to use 32-bit
- * accesses to the 8250.
  */
-#include <linux/serial_reg.h>
 
 #define UART_SHIFT 2
 #define PICOXCELL_UART1_BASE		0x80230000
@@ -19,17 +16,4 @@
 		ldr	\rp, =PICOXCELL_UART1_BASE
 		.endm
 
-		.macro	senduart,rd,rx
+#include "8250_32.S"
-		str	\rd, [\rx, #UART_TX << UART_SHIFT]
-		.endm
-
-		.macro	busyuart,rd,rx
-1002:		ldr	\rd, [\rx, #UART_LSR << UART_SHIFT]
-		and	\rd, \rd, #UART_LSR_TEMT | UART_LSR_THRE
-		teq	\rd, #UART_LSR_TEMT | UART_LSR_THRE
-		bne	1002b
-		.endm
-
-		/* The UART's don't have any flow control IO's wired up. */
-		.macro	waituart,rd,rx
-		.endm

arch/arm/include/debug/socfpga.S

@@ -7,6 +7,9 @@
  * published by the Free Software Foundation.
  */
 
+#define UART_SHIFT 2
+#define DEBUG_LL_UART_OFFSET	0x00002000
+
 		.macro	addruart, rp, rv, tmp
 		mov	\rp, #DEBUG_LL_UART_OFFSET
 		orr	\rp, \rp, #0x00c00000
@@ -14,3 +17,5 @@
 		orr	\rp, \rp, #0xff000000	@ physical base
 		.endm
 
+#include "8250_32.S"
+

arch/arm/kernel/irq.c

@@ -34,6 +34,7 @@
 #include <linux/list.h>
 #include <linux/kallsyms.h>
 #include <linux/proc_fs.h>
+#include <linux/export.h>
 
 #include <asm/exception.h>
 #include <asm/mach/arch.h>
@@ -109,6 +110,7 @@ void set_irq_flags(unsigned int irq, unsigned int iflags)
 	/* Order is clear bits in "clr" then set bits in "set" */
 	irq_modify_status(irq, clr, set & ~clr);
 }
+EXPORT_SYMBOL_GPL(set_irq_flags);
 
 void __init init_IRQ(void)
 {

arch/arm/kernel/kprobes-test-arm.c

@@ -366,7 +366,9 @@ void kprobe_arm_test_cases(void)
 	TEST_UNSUPPORTED(".word 0xe04f0392 @ umaal r0, pc, r2, r3")
 	TEST_UNSUPPORTED(".word 0xe0500090 @ undef")
 	TEST_UNSUPPORTED(".word 0xe05fff9f @ undef")
+#endif
 
+#if __LINUX_ARM_ARCH__ >= 7
 	TEST_RRR(  "mls		r0, r",1, VAL1,", r",2, VAL2,", r",3,  VAL3,"")
 	TEST_RRR(  "mlshi	r7, r",8, VAL3,", r",9, VAL1,", r",10, VAL2,"")
 	TEST_RR(   "mls		lr, r",1, VAL2,", r",2, VAL3,", r13")
@@ -456,6 +458,8 @@ void kprobe_arm_test_cases(void)
 	TEST_UNSUPPORTED(".word	0xe1700090") /* Unallocated space */
 #if __LINUX_ARM_ARCH__ >= 6
 	TEST_UNSUPPORTED("ldrex	r2, [sp]")
+#endif
+#if (__LINUX_ARM_ARCH__ >= 7) || defined(CONFIG_CPU_32v6K)
 	TEST_UNSUPPORTED("strexd	r0, r2, r3, [sp]")
 	TEST_UNSUPPORTED("ldrexd	r2, r3, [sp]")
 	TEST_UNSUPPORTED("strexb	r0, r2, [sp]")

arch/arm/kernel/machine_kexec.c

@@ -45,10 +45,9 @@ int machine_kexec_prepare(struct kimage *image)
 	for (i = 0; i < image->nr_segments; i++) {
 		current_segment = &image->segment[i];
 
-		err = memblock_is_region_memory(current_segment->mem,
+		if (!memblock_is_region_memory(current_segment->mem,
-						current_segment->memsz);
+					       current_segment->memsz))
-		if (err)
+			return -EINVAL;
-			return - EINVAL;
 
 		err = get_user(header, (__be32*)current_segment->buf);
 		if (err)

arch/arm/kernel/perf_event.c

@@ -96,6 +96,10 @@ armpmu_event_set_period(struct perf_event *event,
 	s64 period = hwc->sample_period;
 	int ret = 0;
 
+	/* The period may have been changed by PERF_EVENT_IOC_PERIOD */
+	if (unlikely(period != hwc->last_period))
+		left = period - (hwc->last_period - left);
+
 	if (unlikely(left <= -period)) {
 		left = period;
 		local64_set(&hwc->period_left, left);

arch/arm/kernel/smp.c

@@ -294,18 +294,24 @@ static void percpu_timer_setup(void);
 asmlinkage void __cpuinit secondary_start_kernel(void)
 {
 	struct mm_struct *mm = &init_mm;
-	unsigned int cpu = smp_processor_id();
+	unsigned int cpu;
+
+	/*
+	 * The identity mapping is uncached (strongly ordered), so
+	 * switch away from it before attempting any exclusive accesses.
+	 */
+	cpu_switch_mm(mm->pgd, mm);
+	enter_lazy_tlb(mm, current);
+	local_flush_tlb_all();
 
 	/*
 	 * All kernel threads share the same mm context; grab a
 	 * reference and switch to it.
 	 */
+	cpu = smp_processor_id();
 	atomic_inc(&mm->mm_count);
 	current->active_mm = mm;
 	cpumask_set_cpu(cpu, mm_cpumask(mm));
-	cpu_switch_mm(mm->pgd, mm);
-	enter_lazy_tlb(mm, current);
-	local_flush_tlb_all();
 
 	printk("CPU%u: Booted secondary processor\n", cpu);
 

arch/arm/kernel/smp_twd.c

@@ -42,10 +42,10 @@ static void twd_set_mode(enum clock_event_mode mode,
 
 	switch (mode) {
 	case CLOCK_EVT_MODE_PERIODIC:
-		/* timer load already set up */
 		ctrl = TWD_TIMER_CONTROL_ENABLE | TWD_TIMER_CONTROL_IT_ENABLE
 			| TWD_TIMER_CONTROL_PERIODIC;
-		__raw_writel(twd_timer_rate / HZ, twd_base + TWD_TIMER_LOAD);
+		__raw_writel(DIV_ROUND_CLOSEST(twd_timer_rate, HZ),
+			twd_base + TWD_TIMER_LOAD);
 		break;
 	case CLOCK_EVT_MODE_ONESHOT:
 		/* period set, and timer enabled in 'next_event' hook */

arch/arm/lib/delay.c

@@ -45,6 +45,7 @@ int read_current_timer(unsigned long *timer_val)
 	*timer_val = delay_timer->read_current_timer();
 	return 0;
 }
+EXPORT_SYMBOL_GPL(read_current_timer);
 
 static void __timer_delay(unsigned long cycles)
 {

arch/arm/mach-at91/Kconfig

@@ -21,19 +21,13 @@ config SOC_AT91SAM9
 	bool
 	select CPU_ARM926T
 	select GENERIC_CLOCKEVENTS
+	select MULTI_IRQ_HANDLER
+	select SPARSE_IRQ
 
 menu "Atmel AT91 System-on-Chip"
 
 comment "Atmel AT91 Processor"
 
-config SOC_AT91SAM9
-	bool
-	select AT91_SAM9_SMC
-	select AT91_SAM9_TIME
-	select CPU_ARM926T
-	select MULTI_IRQ_HANDLER
-	select SPARSE_IRQ
-
 config SOC_AT91RM9200
 	bool "AT91RM9200"
 	select CPU_ARM920T

arch/arm/mach-at91/at91rm9200.c

@@ -187,7 +187,7 @@ static struct clk_lookup periph_clocks_lookups[] = {
 	CLKDEV_CON_DEV_ID("pclk", "ssc.0", &ssc0_clk),
 	CLKDEV_CON_DEV_ID("pclk", "ssc.1", &ssc1_clk),
 	CLKDEV_CON_DEV_ID("pclk", "ssc.2", &ssc2_clk),
-	CLKDEV_CON_DEV_ID(NULL, "i2c-at91rm9200", &twi_clk),
+	CLKDEV_CON_DEV_ID(NULL, "i2c-at91rm9200.0", &twi_clk),
 	/* fake hclk clock */
 	CLKDEV_CON_DEV_ID("hclk", "at91_ohci", &ohci_clk),
 	CLKDEV_CON_ID("pioA", &pioA_clk),

arch/arm/mach-at91/at91rm9200_devices.c

@@ -479,7 +479,7 @@ static struct i2c_gpio_platform_data pdata = {
 
 static struct platform_device at91rm9200_twi_device = {
 	.name			= "i2c-gpio",
-	.id			= -1,
+	.id			= 0,
 	.dev.platform_data	= &pdata,
 };
 
@@ -512,7 +512,7 @@ static struct resource twi_resources[] = {
 
 static struct platform_device at91rm9200_twi_device = {
 	.name		= "i2c-at91rm9200",
-	.id		= -1,
+	.id		= 0,
 	.resource	= twi_resources,
 	.num_resources	= ARRAY_SIZE(twi_resources),
 };

arch/arm/mach-at91/at91sam9260.c

@@ -211,8 +211,8 @@ static struct clk_lookup periph_clocks_lookups[] = {
 	CLKDEV_CON_DEV_ID("t1_clk", "atmel_tcb.1", &tc4_clk),
 	CLKDEV_CON_DEV_ID("t2_clk", "atmel_tcb.1", &tc5_clk),
 	CLKDEV_CON_DEV_ID("pclk", "ssc.0", &ssc_clk),
-	CLKDEV_CON_DEV_ID(NULL, "i2c-at91sam9260", &twi_clk),
+	CLKDEV_CON_DEV_ID(NULL, "i2c-at91sam9260.0", &twi_clk),
-	CLKDEV_CON_DEV_ID(NULL, "i2c-at91sam9g20", &twi_clk),
+	CLKDEV_CON_DEV_ID(NULL, "i2c-at91sam9g20.0", &twi_clk),
 	/* more usart lookup table for DT entries */
 	CLKDEV_CON_DEV_ID("usart", "fffff200.serial", &mck),
 	CLKDEV_CON_DEV_ID("usart", "fffb0000.serial", &usart0_clk),

arch/arm/mach-at91/at91sam9260_devices.c

@@ -389,7 +389,7 @@ static struct i2c_gpio_platform_data pdata = {
 
 static struct platform_device at91sam9260_twi_device = {
 	.name			= "i2c-gpio",
-	.id			= -1,
+	.id			= 0,
 	.dev.platform_data	= &pdata,
 };
 
@@ -421,7 +421,7 @@ static struct resource twi_resources[] = {
 };
 
 static struct platform_device at91sam9260_twi_device = {
-	.id		= -1,
+	.id		= 0,
 	.resource	= twi_resources,
 	.num_resources	= ARRAY_SIZE(twi_resources),
 };

arch/arm/mach-at91/at91sam9261.c

@@ -178,8 +178,8 @@ static struct clk_lookup periph_clocks_lookups[] = {
 	CLKDEV_CON_DEV_ID("pclk", "ssc.1", &ssc1_clk),
 	CLKDEV_CON_DEV_ID("pclk", "ssc.2", &ssc2_clk),
 	CLKDEV_CON_DEV_ID("hclk", "at91_ohci", &hck0),
-	CLKDEV_CON_DEV_ID(NULL, "i2c-at91sam9261", &twi_clk),
+	CLKDEV_CON_DEV_ID(NULL, "i2c-at91sam9261.0", &twi_clk),
-	CLKDEV_CON_DEV_ID(NULL, "i2c-at91sam9g10", &twi_clk),
+	CLKDEV_CON_DEV_ID(NULL, "i2c-at91sam9g10.0", &twi_clk),
 	CLKDEV_CON_ID("pioA", &pioA_clk),
 	CLKDEV_CON_ID("pioB", &pioB_clk),
 	CLKDEV_CON_ID("pioC", &pioC_clk),

arch/arm/mach-at91/at91sam9261_devices.c

@@ -285,7 +285,7 @@ static struct i2c_gpio_platform_data pdata = {
 
 static struct platform_device at91sam9261_twi_device = {
 	.name			= "i2c-gpio",
-	.id			= -1,
+	.id			= 0,
 	.dev.platform_data	= &pdata,
 };
 
@@ -317,7 +317,7 @@ static struct resource twi_resources[] = {
 };
 
 static struct platform_device at91sam9261_twi_device = {
-	.id		= -1,
+	.id		= 0,
 	.resource	= twi_resources,
 	.num_resources	= ARRAY_SIZE(twi_resources),
 };

arch/arm/mach-at91/at91sam9263.c

@@ -193,7 +193,7 @@ static struct clk_lookup periph_clocks_lookups[] = {
 	CLKDEV_CON_DEV_ID("spi_clk", "atmel_spi.0", &spi0_clk),
 	CLKDEV_CON_DEV_ID("spi_clk", "atmel_spi.1", &spi1_clk),
 	CLKDEV_CON_DEV_ID("t0_clk", "atmel_tcb.0", &tcb_clk),
-	CLKDEV_CON_DEV_ID(NULL, "i2c-at91sam9260", &twi_clk),
+	CLKDEV_CON_DEV_ID(NULL, "i2c-at91sam9260.0", &twi_clk),
 	/* fake hclk clock */
 	CLKDEV_CON_DEV_ID("hclk", "at91_ohci", &ohci_clk),
 	CLKDEV_CON_ID("pioA", &pioA_clk),

arch/arm/mach-at91/at91sam9263_devices.c

@@ -567,7 +567,7 @@ static struct i2c_gpio_platform_data pdata = {
 
 static struct platform_device at91sam9263_twi_device = {
 	.name			= "i2c-gpio",
-	.id			= -1,
+	.id			= 0,
 	.dev.platform_data	= &pdata,
 };
 
@@ -600,7 +600,7 @@ static struct resource twi_resources[] = {
 
 static struct platform_device at91sam9263_twi_device = {
 	.name		= "i2c-at91sam9260",
-	.id		= -1,
+	.id		= 0,
 	.resource	= twi_resources,
 	.num_resources	= ARRAY_SIZE(twi_resources),
 };

arch/arm/mach-at91/at91sam9rl_devices.c

@@ -314,7 +314,7 @@ static struct i2c_gpio_platform_data pdata = {
 
 static struct platform_device at91sam9rl_twi_device = {
 	.name			= "i2c-gpio",
-	.id			= -1,
+	.id			= 0,
 	.dev.platform_data	= &pdata,
 };
 
@@ -347,7 +347,7 @@ static struct resource twi_resources[] = {
 
 static struct platform_device at91sam9rl_twi_device = {
 	.name		= "i2c-at91sam9g20",
-	.id		= -1,
+	.id		= 0,
 	.resource	= twi_resources,
 	.num_resources	= ARRAY_SIZE(twi_resources),
 };

arch/arm/mach-at91/at91x40.c

@@ -88,6 +88,6 @@ void __init at91x40_init_interrupts(unsigned int priority[NR_AIC_IRQS])
 	if (!priority)
 		priority = at91x40_default_irq_priority;
 
-	at91_aic_init(priority);
+	at91_aic_init(priority, at91_extern_irq);
 }
 

arch/arm/mach-at91/board-neocore926.c

@@ -129,7 +129,7 @@ static struct spi_board_info neocore926_spi_devices[] = {
 		.max_speed_hz	= 125000 * 16,
 		.bus_num	= 0,
 		.platform_data	= &ads_info,
-		.irq		= AT91SAM9263_ID_IRQ1,
+		.irq		= NR_IRQS_LEGACY + AT91SAM9263_ID_IRQ1,
 	},
 #endif
 };

arch/arm/mach-at91/board-sam9261ek.c

@@ -309,7 +309,7 @@ static struct spi_board_info ek_spi_devices[] = {
 		.max_speed_hz	= 125000 * 26,	/* (max sample rate @ 3V) * (cmd + data + overhead) */
 		.bus_num	= 0,
 		.platform_data	= &ads_info,
-		.irq		= AT91SAM9261_ID_IRQ0,
+		.irq		= NR_IRQS_LEGACY + AT91SAM9261_ID_IRQ0,
 		.controller_data = (void *) AT91_PIN_PA28,	/* CS pin */
 	},
 #endif

arch/arm/mach-at91/board-sam9263ek.c

@@ -132,7 +132,7 @@ static struct spi_board_info ek_spi_devices[] = {
 		.max_speed_hz	= 125000 * 26,	/* (max sample rate @ 3V) * (cmd + data + overhead) */
 		.bus_num	= 0,
 		.platform_data	= &ads_info,
-		.irq		= AT91SAM9263_ID_IRQ1,
+		.irq		= NR_IRQS_LEGACY + AT91SAM9263_ID_IRQ1,
 	},
 #endif
 };

arch/arm/mach-at91/generic.h

@@ -26,7 +26,8 @@ extern void __init at91_dt_initialize(void);
 extern void __init at91_init_irq_default(void);
 extern void __init at91_init_interrupts(unsigned int priority[]);
 extern void __init at91x40_init_interrupts(unsigned int priority[]);
-extern void __init at91_aic_init(unsigned int priority[]);
+extern void __init at91_aic_init(unsigned int priority[],
+				 unsigned int ext_irq_mask);
 extern int  __init at91_aic_of_init(struct device_node *node,
 				    struct device_node *parent);
 extern int  __init at91_aic5_of_init(struct device_node *node,

arch/arm/mach-at91/irq.c

@@ -502,14 +502,19 @@ int __init at91_aic5_of_init(struct device_node *node,
 /*
  * Initialize the AIC interrupt controller.
  */
-void __init at91_aic_init(unsigned int *priority)
+void __init at91_aic_init(unsigned int *priority, unsigned int ext_irq_mask)
 {
 	unsigned int i;
 	int irq_base;
 
-	if (at91_aic_pm_init())
+	at91_extern_irq = kzalloc(BITS_TO_LONGS(n_irqs)
+				  * sizeof(*at91_extern_irq), GFP_KERNEL);
+
+	if (at91_aic_pm_init() || at91_extern_irq == NULL)
 		panic("Unable to allocate bit maps\n");
 
+	*at91_extern_irq = ext_irq_mask;
+
 	at91_aic_base = ioremap(AT91_AIC, 512);
 	if (!at91_aic_base)
 		panic("Unable to ioremap AIC registers\n");

arch/arm/mach-at91/setup.c

@@ -47,7 +47,7 @@ void __init at91_init_irq_default(void)
 void __init at91_init_interrupts(unsigned int *priority)
 {
 	/* Initialize the AIC interrupt controller */
-	at91_aic_init(priority);
+	at91_aic_init(priority, at91_extern_irq);
 
 	/* Enable GPIO interrupts */
 	at91_gpio_irq_setup();
@@ -151,7 +151,7 @@ static void __init soc_detect(u32 dbgu_base)
 	}
 
 	/* at91sam9g10 */
-	if ((cidr & ~AT91_CIDR_EXT) == ARCH_ID_AT91SAM9G10) {
+	if ((socid & ~AT91_CIDR_EXT) == ARCH_ID_AT91SAM9G10) {
 		at91_soc_initdata.type = AT91_SOC_SAM9G10;
 		at91_boot_soc = at91sam9261_soc;
 	}

arch/arm/mach-exynos/common.c

@@ -47,6 +47,7 @@
 #include <plat/fimc-core.h>
 #include <plat/iic-core.h>
 #include <plat/tv-core.h>
+#include <plat/spi-core.h>
 #include <plat/regs-serial.h>
 
 #include "common.h"
@@ -346,6 +347,8 @@ static void __init exynos4_map_io(void)
 
 	s5p_fb_setname(0, "exynos4-fb");
 	s5p_hdmi_setname("exynos4-hdmi");
+
+	s3c64xx_spi_setname("exynos4210-spi");
 }
 
 static void __init exynos5_map_io(void)
@@ -366,6 +369,8 @@ static void __init exynos5_map_io(void)
 	s3c_i2c0_setname("s3c2440-i2c");
 	s3c_i2c1_setname("s3c2440-i2c");
 	s3c_i2c2_setname("s3c2440-i2c");
+
+	s3c64xx_spi_setname("exynos4210-spi");
 }
 
 static void __init exynos4_init_clocks(int xtal)

arch/arm/mach-exynos/mach-exynos4-dt.c

@@ -99,6 +99,7 @@ static char const *exynos4_dt_compat[] __initdata = {
 
 DT_MACHINE_START(EXYNOS4210_DT, "Samsung Exynos4 (Flattened Device Tree)")
 	/* Maintainer: Thomas Abraham <thomas.abraham@linaro.org> */
+	.smp		= smp_ops(exynos_smp_ops),
 	.init_irq	= exynos4_init_irq,
 	.map_io		= exynos4_dt_map_io,
 	.handle_irq	= gic_handle_irq,

arch/arm/mach-imx/clk-busy.c

@@ -108,7 +108,7 @@ struct clk *imx_clk_busy_divider(const char *name, const char *parent_name,
 	busy->div.hw.init = &init;
 
 	clk = clk_register(NULL, &busy->div.hw);
-	if (!clk)
+	if (IS_ERR(clk))
 		kfree(busy);
 
 	return clk;

arch/arm/mach-imx/clk-imx25.c

@@ -127,8 +127,8 @@ int __init mx25_clocks_init(void)
 	clk[esdhc2_ipg_per] = imx_clk_gate("esdhc2_ipg_per", "per4", ccm(CCM_CGCR0),  4);
 	clk[gpt_ipg_per] = imx_clk_gate("gpt_ipg_per", "per5", ccm(CCM_CGCR0),  5);
 	clk[i2c_ipg_per] = imx_clk_gate("i2c_ipg_per", "per6", ccm(CCM_CGCR0),  6);
-	clk[lcdc_ipg_per] = imx_clk_gate("lcdc_ipg_per", "per8", ccm(CCM_CGCR0),  7);
+	clk[lcdc_ipg_per] = imx_clk_gate("lcdc_ipg_per", "per7", ccm(CCM_CGCR0),  7);
-	clk[nfc_ipg_per] = imx_clk_gate("nfc_ipg_per", "ipg_per", ccm(CCM_CGCR0),  8);
+	clk[nfc_ipg_per] = imx_clk_gate("nfc_ipg_per", "per8", ccm(CCM_CGCR0),  8);
 	clk[ssi1_ipg_per] = imx_clk_gate("ssi1_ipg_per", "per13", ccm(CCM_CGCR0), 13);
 	clk[ssi2_ipg_per] = imx_clk_gate("ssi2_ipg_per", "per14", ccm(CCM_CGCR0), 14);
 	clk[uart_ipg_per] = imx_clk_gate("uart_ipg_per", "per15", ccm(CCM_CGCR0), 15);

arch/arm/mach-imx/clk-imx27.c

@@ -109,7 +109,7 @@ int __init mx27_clocks_init(unsigned long fref)
 	clk[per3_div] = imx_clk_divider("per3_div", "mpll_main2", CCM_PCDR1, 16, 6);
 	clk[per4_div] = imx_clk_divider("per4_div", "mpll_main2", CCM_PCDR1, 24, 6);
 	clk[vpu_sel] = imx_clk_mux("vpu_sel", CCM_CSCR, 21, 1, vpu_sel_clks, ARRAY_SIZE(vpu_sel_clks));
-	clk[vpu_div] = imx_clk_divider("vpu_div", "vpu_sel", CCM_PCDR0, 10, 3);
+	clk[vpu_div] = imx_clk_divider("vpu_div", "vpu_sel", CCM_PCDR0, 10, 6);
 	clk[usb_div] = imx_clk_divider("usb_div", "spll", CCM_CSCR, 28, 3);
 	clk[cpu_sel] = imx_clk_mux("cpu_sel", CCM_CSCR, 15, 1, cpu_sel_clks, ARRAY_SIZE(cpu_sel_clks));
 	clk[clko_sel] = imx_clk_mux("clko_sel", CCM_CCSR, 0, 5, clko_sel_clks, ARRAY_SIZE(clko_sel_clks));
@@ -121,7 +121,7 @@ int __init mx27_clocks_init(unsigned long fref)
 	clk[ssi1_sel] = imx_clk_mux("ssi1_sel", CCM_CSCR, 22, 1, ssi_sel_clks, ARRAY_SIZE(ssi_sel_clks));
 	clk[ssi2_sel] = imx_clk_mux("ssi2_sel", CCM_CSCR, 23, 1, ssi_sel_clks, ARRAY_SIZE(ssi_sel_clks));
 	clk[ssi1_div] = imx_clk_divider("ssi1_div", "ssi1_sel", CCM_PCDR0, 16, 6);
-	clk[ssi2_div] = imx_clk_divider("ssi2_div", "ssi2_sel", CCM_PCDR0, 26, 3);
+	clk[ssi2_div] = imx_clk_divider("ssi2_div", "ssi2_sel", CCM_PCDR0, 26, 6);
 	clk[clko_en] = imx_clk_gate("clko_en", "clko_div", CCM_PCCR0, 0);
 	clk[ssi2_ipg_gate] = imx_clk_gate("ssi2_ipg_gate", "ipg", CCM_PCCR0, 0);
 	clk[ssi1_ipg_gate] = imx_clk_gate("ssi1_ipg_gate", "ipg", CCM_PCCR0, 1);

arch/arm/mach-imx/mm-imx3.c

@@ -108,9 +108,8 @@ void __init imx3_init_l2x0(void)
 	}
 
 	l2x0_base = ioremap(MX3x_L2CC_BASE_ADDR, 4096);
-	if (IS_ERR(l2x0_base)) {
+	if (!l2x0_base) {
-		printk(KERN_ERR "remapping L2 cache area failed with %ld\n",
+		printk(KERN_ERR "remapping L2 cache area failed\n");
-				PTR_ERR(l2x0_base));
 		return;
 	}
 

arch/arm/mach-omap2/Kconfig

@@ -11,7 +11,6 @@ config ARCH_OMAP2PLUS_TYPICAL
 	select I2C_OMAP
 	select MENELAUS if ARCH_OMAP2
 	select NEON if ARCH_OMAP3 || ARCH_OMAP4 || SOC_OMAP5
-	select PINCTRL
 	select PM_RUNTIME
 	select REGULATOR
 	select SERIAL_OMAP

arch/arm/mach-omap2/board-omap3beagle.c

@@ -24,6 +24,7 @@
 #include <linux/input.h>
 #include <linux/gpio_keys.h>
 #include <linux/opp.h>
+#include <linux/cpu.h>
 
 #include <linux/mtd/mtd.h>
 #include <linux/mtd/partitions.h>
@@ -444,27 +445,31 @@ static struct omap_board_mux board_mux[] __initdata = {
 };
 #endif
 
-static void __init beagle_opp_init(void)
+static int __init beagle_opp_init(void)
 {
 	int r = 0;
 
-	/* Initialize the omap3 opp table */
+	if (!machine_is_omap3_beagle())
-	if (omap3_opp_init()) {
+		return 0;
+
+	/* Initialize the omap3 opp table if not already created. */
+	r = omap3_opp_init();
+	if (IS_ERR_VALUE(r) && (r != -EEXIST)) {
 		pr_err("%s: opp default init failed\n", __func__);
-		return;
+		return r;
 	}
 
 	/* Custom OPP enabled for all xM versions */
 	if (cpu_is_omap3630()) {
 		struct device *mpu_dev, *iva_dev;
 
-		mpu_dev = omap_device_get_by_hwmod_name("mpu");
+		mpu_dev = get_cpu_device(0);
 		iva_dev = omap_device_get_by_hwmod_name("iva");
 
 		if (IS_ERR(mpu_dev) || IS_ERR(iva_dev)) {
 			pr_err("%s: Aiee.. no mpu/dsp devices? %p %p\n",
 				__func__, mpu_dev, iva_dev);
-			return;
+			return -ENODEV;
 		}
 		/* Enable MPU 1GHz and lower opps */
 		r = opp_enable(mpu_dev, 800000000);
@@ -484,8 +489,9 @@ static void __init beagle_opp_init(void)
 			opp_disable(iva_dev, 660000000);
 		}
 	}
-	return;
+	return 0;
 }
+device_initcall(beagle_opp_init);
 
 static void __init omap3_beagle_init(void)
 {
@@ -522,8 +528,6 @@ static void __init omap3_beagle_init(void)
 	/* Ensure SDRC pins are mux'd for self-refresh */
 	omap_mux_init_signal("sdrc_cke0", OMAP_PIN_OUTPUT);
 	omap_mux_init_signal("sdrc_cke1", OMAP_PIN_OUTPUT);
-
-	beagle_opp_init();
 }
 
 MACHINE_START(OMAP3_BEAGLE, "OMAP3 Beagle Board")

arch/arm/mach-omap2/clock33xx_data.c

@@ -1073,6 +1073,8 @@ static struct omap_clk am33xx_clks[] = {
 	CLK(NULL,	"gfx_fck_div_ck",	&gfx_fck_div_ck,	CK_AM33XX),
 	CLK(NULL,	"sysclkout_pre_ck",	&sysclkout_pre_ck,	CK_AM33XX),
 	CLK(NULL,	"clkout2_ck",		&clkout2_ck,	CK_AM33XX),
+	CLK(NULL,	"timer_32k_ck",		&clkdiv32k_ick,	CK_AM33XX),
+	CLK(NULL,	"timer_sys_ck",		&sys_clkin_ck,	CK_AM33XX),
 };
 
 int __init am33xx_clk_init(void)

arch/arm/mach-omap2/mux34xx.c

@@ -614,16 +614,16 @@ static struct omap_mux __initdata omap3_muxmodes[] = {
 		"sys_off_mode", NULL, NULL, NULL,
 		"gpio_9", NULL, NULL, "safe_mode"),
 	_OMAP3_MUXENTRY(UART1_CTS, 150,
-		"uart1_cts", NULL, NULL, NULL,
+		"uart1_cts", "ssi1_rdy_tx", NULL, NULL,
 		"gpio_150", "hsusb3_tll_clk", NULL, "safe_mode"),
 	_OMAP3_MUXENTRY(UART1_RTS, 149,
-		"uart1_rts", NULL, NULL, NULL,
+		"uart1_rts", "ssi1_flag_tx", NULL, NULL,
 		"gpio_149", NULL, NULL, "safe_mode"),
 	_OMAP3_MUXENTRY(UART1_RX, 151,
-		"uart1_rx", NULL, "mcbsp1_clkr", "mcspi4_clk",
+		"uart1_rx", "ss1_wake_tx", "mcbsp1_clkr", "mcspi4_clk",
 		"gpio_151", NULL, NULL, "safe_mode"),
 	_OMAP3_MUXENTRY(UART1_TX, 148,
-		"uart1_tx", NULL, NULL, NULL,
+		"uart1_tx", "ssi1_dat_tx", NULL, NULL,
 		"gpio_148", NULL, NULL, "safe_mode"),
 	_OMAP3_MUXENTRY(UART2_CTS, 144,
 		"uart2_cts", "mcbsp3_dx", "gpt9_pwm_evt", NULL,

arch/arm/mach-omap2/pm.h

@@ -91,6 +91,7 @@ extern void omap3_save_scratchpad_contents(void);
 
 #define PM_RTA_ERRATUM_i608		(1 << 0)
 #define PM_SDRC_WAKEUP_ERRATUM_i583	(1 << 1)
+#define PM_PER_MEMORIES_ERRATUM_i582	(1 << 2)
 
 #if defined(CONFIG_PM) && defined(CONFIG_ARCH_OMAP3)
 extern u16 pm34xx_errata;

arch/arm/mach-omap2/pm34xx.c

@@ -652,14 +652,17 @@ static void __init pm_errata_configure(void)
 		/* Enable the l2 cache toggling in sleep logic */
 		enable_omap3630_toggle_l2_on_restore();
 		if (omap_rev() < OMAP3630_REV_ES1_2)
-			pm34xx_errata |= PM_SDRC_WAKEUP_ERRATUM_i583;
+			pm34xx_errata |= (PM_SDRC_WAKEUP_ERRATUM_i583 |
+					  PM_PER_MEMORIES_ERRATUM_i582);
+	} else if (cpu_is_omap34xx()) {
+		pm34xx_errata |= PM_PER_MEMORIES_ERRATUM_i582;
 	}
 }
 
 int __init omap3_pm_init(void)
 {
 	struct power_state *pwrst, *tmp;
-	struct clockdomain *neon_clkdm, *mpu_clkdm;
+	struct clockdomain *neon_clkdm, *mpu_clkdm, *per_clkdm, *wkup_clkdm;
 	int ret;
 
 	if (!omap3_has_io_chain_ctrl())
@@ -711,6 +714,8 @@ int __init omap3_pm_init(void)
 
 	neon_clkdm = clkdm_lookup("neon_clkdm");
 	mpu_clkdm = clkdm_lookup("mpu_clkdm");
+	per_clkdm = clkdm_lookup("per_clkdm");
+	wkup_clkdm = clkdm_lookup("wkup_clkdm");
 
 #ifdef CONFIG_SUSPEND
 	omap_pm_suspend = omap3_pm_suspend;
@@ -727,6 +732,27 @@ int __init omap3_pm_init(void)
 	if (IS_PM34XX_ERRATUM(PM_RTA_ERRATUM_i608))
 		omap3630_ctrl_disable_rta();
 
+	/*
+	 * The UART3/4 FIFO and the sidetone memory in McBSP2/3 are
+	 * not correctly reset when the PER powerdomain comes back
+	 * from OFF or OSWR when the CORE powerdomain is kept active.
+	 * See OMAP36xx Erratum i582 "PER Domain reset issue after
+	 * Domain-OFF/OSWR Wakeup".  This wakeup dependency is not a
+	 * complete workaround.  The kernel must also prevent the PER
+	 * powerdomain from going to OSWR/OFF while the CORE
+	 * powerdomain is not going to OSWR/OFF.  And if PER last
+	 * power state was off while CORE last power state was ON, the
+	 * UART3/4 and McBSP2/3 SIDETONE devices need to run a
+	 * self-test using their loopback tests; if that fails, those
+	 * devices are unusable until the PER/CORE can complete a transition
+	 * from ON to OSWR/OFF and then back to ON.
+	 *
+	 * XXX Technically this workaround is only needed if off-mode
+	 * or OSWR is enabled.
+	 */
+	if (IS_PM34XX_ERRATUM(PM_PER_MEMORIES_ERRATUM_i582))
+		clkdm_add_wkdep(per_clkdm, wkup_clkdm);
+
 	clkdm_add_wkdep(neon_clkdm, mpu_clkdm);
 	if (omap_type() != OMAP2_DEVICE_TYPE_GP) {
 		omap3_secure_ram_storage =

arch/arm/mach-omap2/serial.c

@@ -329,6 +329,11 @@ void __init omap_serial_init_port(struct omap_board_data *bdata,
 
 	oh->mux = omap_hwmod_mux_init(bdata->pads, bdata->pads_cnt);
 
+	if (console_uart_id == bdata->id) {
+		omap_device_enable(pdev);
+		pm_runtime_set_active(&pdev->dev);
+	}
+
 	oh->dev_attr = uart;
 
 	if (((cpu_is_omap34xx() || cpu_is_omap44xx()) && bdata->pads)

arch/arm/mach-s3c24xx/s3c2416.c

@@ -61,6 +61,7 @@
 #include <plat/nand-core.h>
 #include <plat/adc-core.h>
 #include <plat/rtc-core.h>
+#include <plat/spi-core.h>
 
 static struct map_desc s3c2416_iodesc[] __initdata = {
 	IODESC_ENT(WATCHDOG),
@@ -132,6 +133,7 @@ void __init s3c2416_map_io(void)
 	/* initialize device information early */
 	s3c2416_default_sdhci0();
 	s3c2416_default_sdhci1();
+	s3c64xx_spi_setname("s3c2443-spi");
 
 	iotable_init(s3c2416_iodesc, ARRAY_SIZE(s3c2416_iodesc));
 }

arch/arm/mach-s3c24xx/s3c2443.c

@@ -43,6 +43,7 @@
 #include <plat/nand-core.h>
 #include <plat/adc-core.h>
 #include <plat/rtc-core.h>
+#include <plat/spi-core.h>
 
 static struct map_desc s3c2443_iodesc[] __initdata = {
 	IODESC_ENT(WATCHDOG),
@@ -100,6 +101,9 @@ void __init s3c2443_map_io(void)
 	s3c24xx_gpiocfg_default.set_pull = s3c2443_gpio_setpull;
 	s3c24xx_gpiocfg_default.get_pull = s3c2443_gpio_getpull;
 
+	/* initialize device information early */
+	s3c64xx_spi_setname("s3c2443-spi");
+
 	iotable_init(s3c2443_iodesc, ARRAY_SIZE(s3c2443_iodesc));
 }
 

arch/arm/mach-s5p64x0/common.c

@@ -44,6 +44,7 @@
 #include <plat/sdhci.h>
 #include <plat/adc-core.h>
 #include <plat/fb-core.h>
+#include <plat/spi-core.h>
 #include <plat/gpio-cfg.h>
 #include <plat/regs-irqtype.h>
 #include <plat/regs-serial.h>
@@ -179,6 +180,7 @@ void __init s5p6440_map_io(void)
 	/* initialize any device information early */
 	s3c_adc_setname("s3c64xx-adc");
 	s3c_fb_setname("s5p64x0-fb");
+	s3c64xx_spi_setname("s5p64x0-spi");
 
 	s5p64x0_default_sdhci0();
 	s5p64x0_default_sdhci1();
@@ -193,6 +195,7 @@ void __init s5p6450_map_io(void)
 	/* initialize any device information early */
 	s3c_adc_setname("s3c64xx-adc");
 	s3c_fb_setname("s5p64x0-fb");
+	s3c64xx_spi_setname("s5p64x0-spi");
 
 	s5p64x0_default_sdhci0();
 	s5p64x0_default_sdhci1();

arch/arm/mach-s5pc100/common.c

@@ -45,6 +45,7 @@
 #include <plat/fb-core.h>
 #include <plat/iic-core.h>
 #include <plat/onenand-core.h>
+#include <plat/spi-core.h>
 #include <plat/regs-serial.h>
 #include <plat/watchdog-reset.h>
 
@@ -165,6 +166,8 @@ void __init s5pc100_map_io(void)
 	s3c_onenand_setname("s5pc100-onenand");
 	s3c_fb_setname("s5pc100-fb");
 	s3c_cfcon_setname("s5pc100-pata");
+
+	s3c64xx_spi_setname("s5pc100-spi");
 }
 
 void __init s5pc100_init_clocks(int xtal)

arch/arm/mach-s5pv210/common.c

@@ -43,6 +43,7 @@
 #include <plat/iic-core.h>
 #include <plat/keypad-core.h>
 #include <plat/tv-core.h>
+#include <plat/spi-core.h>
 #include <plat/regs-serial.h>
 
 #include "common.h"
@@ -196,6 +197,8 @@ void __init s5pv210_map_io(void)
 
 	/* setup TV devices */
 	s5p_hdmi_setname("s5pv210-hdmi");
+
+	s3c64xx_spi_setname("s5pv210-spi");
 }
 
 void __init s5pv210_init_clocks(int xtal)

arch/arm/mach-shmobile/setup-r8a7779.c

@@ -247,7 +247,7 @@ void __init r8a7779_add_standard_devices(void)
 {
 #ifdef CONFIG_CACHE_L2X0
 	/* Early BRESP enable, Shared attribute override enable, 64K*16way */
-	l2x0_init((void __iomem __force *)(0xf0100000), 0x40470000, 0x82000fff);
+	l2x0_init(IOMEM(0xf0100000), 0x40470000, 0x82000fff);
 #endif
 	r8a7779_pm_init();
 

arch/arm/mach-ux500/cpu.c

@@ -16,6 +16,7 @@
 #include <linux/stat.h>
 #include <linux/of.h>
 #include <linux/of_irq.h>
+#include <linux/irq.h>
 #include <linux/platform_data/clk-ux500.h>
 
 #include <asm/hardware/gic.h>

arch/arm/mm/alignment.c

@@ -856,8 +856,10 @@ do_alignment(unsigned long addr, unsigned int fsr, struct pt_regs *regs)
 		if (thumb2_32b) {
 			offset.un = 0;
 			handler = do_alignment_t32_to_handler(&instr, regs, &offset);
-		} else
+		} else {
+			offset.un = 0;
 			handler = do_alignment_ldmstm;
+		}
 		break;
 
 	default:

arch/arm/mm/dma-mapping.c

@@ -610,7 +610,7 @@ static void *__dma_alloc(struct device *dev, size_t size, dma_addr_t *handle,
 			 gfp_t gfp, pgprot_t prot, bool is_coherent, const void *caller)
 {
 	u64 mask = get_coherent_dma_mask(dev);
-	struct page *page;
+	struct page *page = NULL;
 	void *addr;
 
 #ifdef CONFIG_DMA_API_DEBUG

arch/arm/mm/vmregion.h

@@ -17,7 +17,6 @@ struct arm_vmregion {
 	struct list_head	vm_list;
 	unsigned long		vm_start;
 	unsigned long		vm_end;
-	void			*priv;
 	int			vm_active;
 	const void		*caller;
 };

arch/arm/plat-mxc/devices/platform-mxc-mmc.c

@@ -55,7 +55,7 @@ struct platform_device *__init imx_add_mxc_mmc(
 	struct resource res[] = {
 		{
 			.start = data->iobase,
-			.end = data->iobase + SZ_4K - 1,
+			.end = data->iobase + data->iosize - 1,
 			.flags = IORESOURCE_MEM,
 		}, {
 			.start = data->irq,

arch/arm/plat-omap/Kconfig

@@ -26,6 +26,7 @@ config ARCH_OMAP2PLUS
 	select CLKDEV_LOOKUP
 	select GENERIC_IRQ_CHIP
 	select OMAP_DM_TIMER
+	select PINCTRL
 	select PROC_DEVICETREE if PROC_FS
 	select SPARSE_IRQ
 	select USE_OF

arch/arm/plat-omap/include/plat/omap-serial.h

@@ -40,10 +40,10 @@
 #define OMAP_UART_WER_MOD_WKUP	0X7F
 
 /* Enable XON/XOFF flow control on output */
-#define OMAP_UART_SW_TX		0x8
+#define OMAP_UART_SW_TX		0x04
 
 /* Enable XON/XOFF flow control on input */
-#define OMAP_UART_SW_RX		0x2
+#define OMAP_UART_SW_RX		0x04
 
 #define OMAP_UART_SYSC_RESET	0X07
 #define OMAP_UART_TCR_TRIG	0X0F

arch/arm/plat-samsung/include/plat/spi-core.h

@@ -0,0 +1,30 @@
+/*
+ * Copyright (C) 2012 Heiko Stuebner <heiko@sntech.de>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#ifndef __PLAT_S3C_SPI_CORE_H
+#define __PLAT_S3C_SPI_CORE_H
+
+/* These functions are only for use with the core support code, such as
+ * the cpu specific initialisation code
+ */
+
+/* re-define device name depending on support. */
+static inline void s3c64xx_spi_setname(char *name)
+{
+#ifdef CONFIG_S3C64XX_DEV_SPI0
+	s3c64xx_device_spi0.name = name;
+#endif
+#ifdef CONFIG_S3C64XX_DEV_SPI1
+	s3c64xx_device_spi1.name = name;
+#endif
+#ifdef CONFIG_S3C64XX_DEV_SPI2
+	s3c64xx_device_spi2.name = name;
+#endif
+}
+
+#endif /* __PLAT_S3C_SPI_CORE_H */

arch/arm/tools/Makefile

@@ -5,6 +5,6 @@
 #
 
 include/generated/mach-types.h: $(src)/gen-mach-types $(src)/mach-types
-	@echo '  Generating $@'
+	$(kecho) '  Generating $@'
 	@mkdir -p $(dir $@)
 	$(Q)$(AWK) -f $^ > $@ || { rm -f $@; /bin/false; }

arch/arm/xen/grant-table.c

@@ -33,7 +33,7 @@
 #include <xen/page.h>
 #include <xen/grant_table.h>
 
-int arch_gnttab_map_shared(unsigned long *frames, unsigned long nr_gframes,
+int arch_gnttab_map_shared(xen_pfn_t *frames, unsigned long nr_gframes,
 			   unsigned long max_nr_gframes,
 			   void **__shared)
 {

arch/ia64/include/asm/Kbuild

@@ -1,3 +1,4 @@
 
 generic-y += clkdev.h
 generic-y += exec.h
+generic-y += kvm_para.h

arch/ia64/include/asm/kvm_para.h

@@ -1,34 +0,0 @@
-/*
- * Copyright (C) 2007 Xiantao Zhang <xiantao.zhang@intel.com>
- *
- * This program is free software; you can redistribute it and/or modify it
- * under the terms and conditions of the GNU General Public License,
- * version 2, as published by the Free Software Foundation.
- *
- * This program is distributed in the hope it will be useful, but WITHOUT
- * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
- * FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License for
- * more details.
- *
- * You should have received a copy of the GNU General Public License along with
- * this program; if not, write to the Free Software Foundation, Inc., 59 Temple
- * Place - Suite 330, Boston, MA 02111-1307 USA.
- *
- */
-#ifndef __IA64_KVM_PARA_H
-#define __IA64_KVM_PARA_H
-
-#include <uapi/asm/kvm_para.h>
-
-
-static inline unsigned int kvm_arch_para_features(void)
-{
-	return 0;
-}
-
-static inline bool kvm_check_and_clear_guest_paused(void)
-{
-	return false;
-}
-
-#endif

arch/m68k/include/asm/Kbuild

@@ -1,5 +1,3 @@
-include include/asm-generic/Kbuild.asm
-header-y += cachectl.h
 
 generic-y += bitsperlong.h
 generic-y += clkdev.h

arch/m68k/include/asm/ptrace.h

@@ -1,82 +1,10 @@
 #ifndef _M68K_PTRACE_H
 #define _M68K_PTRACE_H
 
-#define PT_D1	   0
+#include <uapi/asm/ptrace.h>
-#define PT_D2	   1
-#define PT_D3	   2
-#define PT_D4	   3
-#define PT_D5	   4
-#define PT_D6	   5
-#define PT_D7	   6
-#define PT_A0	   7
-#define PT_A1	   8
-#define PT_A2	   9
-#define PT_A3	   10
-#define PT_A4	   11
-#define PT_A5	   12
-#define PT_A6	   13
-#define PT_D0	   14
-#define PT_USP	   15
-#define PT_ORIG_D0 16
-#define PT_SR	   17
-#define PT_PC	   18
 
 #ifndef __ASSEMBLY__
 
-/* this struct defines the way the registers are stored on the
-   stack during a system call. */
-
-struct pt_regs {
-  long     d1;
-  long     d2;
-  long     d3;
-  long     d4;
-  long     d5;
-  long     a0;
-  long     a1;
-  long     a2;
-  long     d0;
-  long     orig_d0;
-  long     stkadj;
-#ifdef CONFIG_COLDFIRE
-  unsigned format :  4; /* frame format specifier */
-  unsigned vector : 12; /* vector offset */
-  unsigned short sr;
-  unsigned long  pc;
-#else
-  unsigned short sr;
-  unsigned long  pc;
-  unsigned format :  4; /* frame format specifier */
-  unsigned vector : 12; /* vector offset */
-#endif
-};
-
-/*
- * This is the extended stack used by signal handlers and the context
- * switcher: it's pushed after the normal "struct pt_regs".
- */
-struct switch_stack {
-	unsigned long  d6;
-	unsigned long  d7;
-	unsigned long  a3;
-	unsigned long  a4;
-	unsigned long  a5;
-	unsigned long  a6;
-	unsigned long  retpc;
-};
-
-/* Arbitrarily choose the same ptrace numbers as used by the Sparc code. */
-#define PTRACE_GETREGS            12
-#define PTRACE_SETREGS            13
-#define PTRACE_GETFPREGS          14
-#define PTRACE_SETFPREGS          15
-
-#define PTRACE_GET_THREAD_AREA    25
-
-#define PTRACE_SINGLEBLOCK	33	/* resume execution until next branch */
-
-#ifdef __KERNEL__
-
 #ifndef PS_S
 #define PS_S  (0x2000)
 #define PS_M  (0x1000)
@@ -94,6 +22,5 @@ struct switch_stack {
 #define arch_has_block_step()	(1)
 #endif
 
-#endif /* __KERNEL__ */
 #endif /* __ASSEMBLY__ */
 #endif /* _M68K_PTRACE_H */

arch/m68k/include/asm/setup.h

@@ -19,33 +19,12 @@
 **   Redesign of the boot information structure; moved boot information
 **   structure to bootinfo.h
 */
-
 #ifndef _M68K_SETUP_H
 #define _M68K_SETUP_H
 
+#include <uapi/asm/setup.h>
 
 
-    /*
-     *  Linux/m68k Architectures
-     */
-
-#define MACH_AMIGA    1
-#define MACH_ATARI    2
-#define MACH_MAC      3
-#define MACH_APOLLO   4
-#define MACH_SUN3     5
-#define MACH_MVME147  6
-#define MACH_MVME16x  7
-#define MACH_BVME6000 8
-#define MACH_HP300    9
-#define MACH_Q40     10
-#define MACH_SUN3X   11
-#define MACH_M54XX   12
-
-#define COMMAND_LINE_SIZE 256
-
-#ifdef __KERNEL__
-
 #define CL_SIZE COMMAND_LINE_SIZE
 
 #ifndef __ASSEMBLY__
@@ -194,63 +173,6 @@ extern unsigned long m68k_machtype;
 #  define MACH_TYPE (m68k_machtype)
 #endif
 
-#endif /* __KERNEL__ */
-
-
-    /*
-     *  CPU, FPU and MMU types
-     *
-     *  Note: we may rely on the following equalities:
-     *
-     *      CPU_68020 == MMU_68851
-     *      CPU_68030 == MMU_68030
-     *      CPU_68040 == FPU_68040 == MMU_68040
-     *      CPU_68060 == FPU_68060 == MMU_68060
-     */
-
-#define CPUB_68020     0
-#define CPUB_68030     1
-#define CPUB_68040     2
-#define CPUB_68060     3
-#define CPUB_COLDFIRE  4
-
-#define CPU_68020      (1<<CPUB_68020)
-#define CPU_68030      (1<<CPUB_68030)
-#define CPU_68040      (1<<CPUB_68040)
-#define CPU_68060      (1<<CPUB_68060)
-#define CPU_COLDFIRE   (1<<CPUB_COLDFIRE)
-
-#define FPUB_68881     0
-#define FPUB_68882     1
-#define FPUB_68040     2                       /* Internal FPU */
-#define FPUB_68060     3                       /* Internal FPU */
-#define FPUB_SUNFPA    4                       /* Sun-3 FPA */
-#define FPUB_COLDFIRE  5                       /* ColdFire FPU */
-
-#define FPU_68881      (1<<FPUB_68881)
-#define FPU_68882      (1<<FPUB_68882)
-#define FPU_68040      (1<<FPUB_68040)
-#define FPU_68060      (1<<FPUB_68060)
-#define FPU_SUNFPA     (1<<FPUB_SUNFPA)
-#define FPU_COLDFIRE   (1<<FPUB_COLDFIRE)
-
-#define MMUB_68851     0
-#define MMUB_68030     1                       /* Internal MMU */
-#define MMUB_68040     2                       /* Internal MMU */
-#define MMUB_68060     3                       /* Internal MMU */
-#define MMUB_APOLLO    4                       /* Custom Apollo */
-#define MMUB_SUN3      5                       /* Custom Sun-3 */
-#define MMUB_COLDFIRE  6                       /* Internal MMU */
-
-#define MMU_68851      (1<<MMUB_68851)
-#define MMU_68030      (1<<MMUB_68030)
-#define MMU_68040      (1<<MMUB_68040)
-#define MMU_68060      (1<<MMUB_68060)
-#define MMU_SUN3       (1<<MMUB_SUN3)
-#define MMU_APOLLO     (1<<MMUB_APOLLO)
-#define MMU_COLDFIRE   (1<<MMUB_COLDFIRE)
-
-#ifdef __KERNEL__
 
 #ifndef __ASSEMBLY__
 extern unsigned long m68k_cputype;
@@ -385,6 +307,4 @@ extern int m68k_realnum_memory;		/* real # of memory blocks found */
 extern struct mem_info m68k_memory[NUM_MEMINFO];/* memory description */
 #endif
 
-#endif /* __KERNEL__ */
-
 #endif /* _M68K_SETUP_H */

arch/m68k/include/asm/signal.h

@@ -1,12 +1,8 @@
 #ifndef _M68K_SIGNAL_H
 #define _M68K_SIGNAL_H
 
-#include <linux/types.h>
+#include <uapi/asm/signal.h>
 
-/* Avoid too many header ordering problems.  */
-struct siginfo;
-
-#ifdef __KERNEL__
 /* Most things should be clean enough to redefine this at will, if care
    is taken to make libc match.  */
 
@@ -20,92 +16,6 @@ typedef struct {
 	unsigned long sig[_NSIG_WORDS];
 } sigset_t;
 
-#else
-/* Here we must cater to libcs that poke about in kernel headers.  */
-
-#define NSIG		32
-typedef unsigned long sigset_t;
-
-#endif /* __KERNEL__ */
-
-#define SIGHUP		 1
-#define SIGINT		 2
-#define SIGQUIT		 3
-#define SIGILL		 4
-#define SIGTRAP		 5
-#define SIGABRT		 6
-#define SIGIOT		 6
-#define SIGBUS		 7
-#define SIGFPE		 8
-#define SIGKILL		 9
-#define SIGUSR1		10
-#define SIGSEGV		11
-#define SIGUSR2		12
-#define SIGPIPE		13
-#define SIGALRM		14
-#define SIGTERM		15
-#define SIGSTKFLT	16
-#define SIGCHLD		17
-#define SIGCONT		18
-#define SIGSTOP		19
-#define SIGTSTP		20
-#define SIGTTIN		21
-#define SIGTTOU		22
-#define SIGURG		23
-#define SIGXCPU		24
-#define SIGXFSZ		25
-#define SIGVTALRM	26
-#define SIGPROF		27
-#define SIGWINCH	28
-#define SIGIO		29
-#define SIGPOLL		SIGIO
-/*
-#define SIGLOST		29
-*/
-#define SIGPWR		30
-#define SIGSYS		31
-#define	SIGUNUSED	31
-
-/* These should not be considered constants from userland.  */
-#define SIGRTMIN	32
-#define SIGRTMAX	_NSIG
-
-/*
- * SA_FLAGS values:
- *
- * SA_ONSTACK indicates that a registered stack_t will be used.
- * SA_RESTART flag to get restarting signals (which were the default long ago)
- * SA_NOCLDSTOP flag to turn off SIGCHLD when children stop.
- * SA_RESETHAND clears the handler when the signal is delivered.
- * SA_NOCLDWAIT flag on SIGCHLD to inhibit zombies.
- * SA_NODEFER prevents the current signal from being masked in the handler.
- *
- * SA_ONESHOT and SA_NOMASK are the historical Linux names for the Single
- * Unix names RESETHAND and NODEFER respectively.
- */
-#define SA_NOCLDSTOP	0x00000001
-#define SA_NOCLDWAIT	0x00000002
-#define SA_SIGINFO	0x00000004
-#define SA_ONSTACK	0x08000000
-#define SA_RESTART	0x10000000
-#define SA_NODEFER	0x40000000
-#define SA_RESETHAND	0x80000000
-
-#define SA_NOMASK	SA_NODEFER
-#define SA_ONESHOT	SA_RESETHAND
-
-/*
- * sigaltstack controls
- */
-#define SS_ONSTACK	1
-#define SS_DISABLE	2
-
-#define MINSIGSTKSZ	2048
-#define SIGSTKSZ	8192
-
-#include <asm-generic/signal-defs.h>
-
-#ifdef __KERNEL__
 struct old_sigaction {
 	__sighandler_t sa_handler;
 	old_sigset_t sa_mask;
@@ -123,31 +33,6 @@ struct sigaction {
 struct k_sigaction {
 	struct sigaction sa;
 };
-#else
-/* Here we must cater to libcs that poke about in kernel headers.  */
-
-struct sigaction {
-	union {
-	  __sighandler_t _sa_handler;
-	  void (*_sa_sigaction)(int, struct siginfo *, void *);
-	} _u;
-	sigset_t sa_mask;
-	unsigned long sa_flags;
-	void (*sa_restorer)(void);
-};
-
-#define sa_handler	_u._sa_handler
-#define sa_sigaction	_u._sa_sigaction
-
-#endif /* __KERNEL__ */
-
-typedef struct sigaltstack {
-	void __user *ss_sp;
-	int ss_flags;
-	size_t ss_size;
-} stack_t;
-
-#ifdef __KERNEL__
 #include <asm/sigcontext.h>
 
 #ifndef CONFIG_CPU_HAS_NO_BITFIELDS
@@ -208,5 +93,4 @@ struct pt_regs;
 extern void ptrace_signal_deliver(struct pt_regs *regs, void *cookie);
 #endif /* __uClinux__ */
 
-#endif /* __KERNEL__ */
 #endif /* _M68K_SIGNAL_H */

arch/m68k/include/asm/termios.h

@@ -1,27 +1,8 @@
 #ifndef _M68K_TERMIOS_H
 #define _M68K_TERMIOS_H
 
-#include <asm/termbits.h>
+#include <uapi/asm/termios.h>
-#include <asm/ioctls.h>
 
-struct winsize {
-	unsigned short ws_row;
-	unsigned short ws_col;
-	unsigned short ws_xpixel;
-	unsigned short ws_ypixel;
-};
-
-#define NCC 8
-struct termio {
-	unsigned short c_iflag;		/* input mode flags */
-	unsigned short c_oflag;		/* output mode flags */
-	unsigned short c_cflag;		/* control mode flags */
-	unsigned short c_lflag;		/* local mode flags */
-	unsigned char c_line;		/* line discipline */
-	unsigned char c_cc[NCC];	/* control characters */
-};
-
-#ifdef __KERNEL__
 /*	intr=^C		quit=^|		erase=del	kill=^U
 	eof=^D		vtime=\0	vmin=\1		sxtc=\0
 	start=^Q	stop=^S		susp=^Z		eol=\0
@@ -29,27 +10,6 @@ struct termio {
 	eol2=\0
 */
 #define INIT_C_CC "\003\034\177\025\004\0\1\0\021\023\032\0\022\017\027\026\0"
-#endif
-
-/* modem lines */
-#define TIOCM_LE	0x001
-#define TIOCM_DTR	0x002
-#define TIOCM_RTS	0x004
-#define TIOCM_ST	0x008
-#define TIOCM_SR	0x010
-#define TIOCM_CTS	0x020
-#define TIOCM_CAR	0x040
-#define TIOCM_RNG	0x080
-#define TIOCM_DSR	0x100
-#define TIOCM_CD	TIOCM_CAR
-#define TIOCM_RI	TIOCM_RNG
-#define TIOCM_OUT1	0x2000
-#define TIOCM_OUT2	0x4000
-#define TIOCM_LOOP	0x8000
-
-/* ioctl (fd, TIOCSERGETLSR, &result) where result may be as below */
-
-#ifdef __KERNEL__
 
 /*
  * Translate a "termio" structure into a "termios". Ugh.
@@ -87,6 +47,4 @@ struct termio {
 #define user_termios_to_kernel_termios_1(k, u) copy_from_user(k, u, sizeof(struct termios))
 #define kernel_termios_to_user_termios_1(u, k) copy_to_user(u, k, sizeof(struct termios))
 
-#endif	/* __KERNEL__ */
-
 #endif /* _M68K_TERMIOS_H */

arch/m68k/include/asm/unistd.h

@@ -1,361 +1,10 @@
 #ifndef _ASM_M68K_UNISTD_H_
 #define _ASM_M68K_UNISTD_H_
 
-/*
+#include <uapi/asm/unistd.h>
- * This file contains the system call numbers.
- */
 
-#define __NR_restart_syscall	  0
-#define __NR_exit		  1
-#define __NR_fork		  2
-#define __NR_read		  3
-#define __NR_write		  4
-#define __NR_open		  5
-#define __NR_close		  6
-#define __NR_waitpid		  7
-#define __NR_creat		  8
-#define __NR_link		  9
-#define __NR_unlink		 10
-#define __NR_execve		 11
-#define __NR_chdir		 12
-#define __NR_time		 13
-#define __NR_mknod		 14
-#define __NR_chmod		 15
-#define __NR_chown		 16
-/*#define __NR_break		 17*/
-#define __NR_oldstat		 18
-#define __NR_lseek		 19
-#define __NR_getpid		 20
-#define __NR_mount		 21
-#define __NR_umount		 22
-#define __NR_setuid		 23
-#define __NR_getuid		 24
-#define __NR_stime		 25
-#define __NR_ptrace		 26
-#define __NR_alarm		 27
-#define __NR_oldfstat		 28
-#define __NR_pause		 29
-#define __NR_utime		 30
-/*#define __NR_stty		 31*/
-/*#define __NR_gtty		 32*/
-#define __NR_access		 33
-#define __NR_nice		 34
-/*#define __NR_ftime		 35*/
-#define __NR_sync		 36
-#define __NR_kill		 37
-#define __NR_rename		 38
-#define __NR_mkdir		 39
-#define __NR_rmdir		 40
-#define __NR_dup		 41
-#define __NR_pipe		 42
-#define __NR_times		 43
-/*#define __NR_prof		 44*/
-#define __NR_brk		 45
-#define __NR_setgid		 46
-#define __NR_getgid		 47
-#define __NR_signal		 48
-#define __NR_geteuid		 49
-#define __NR_getegid		 50
-#define __NR_acct		 51
-#define __NR_umount2		 52
-/*#define __NR_lock		 53*/
-#define __NR_ioctl		 54
-#define __NR_fcntl		 55
-/*#define __NR_mpx		 56*/
-#define __NR_setpgid		 57
-/*#define __NR_ulimit		 58*/
-/*#define __NR_oldolduname	 59*/
-#define __NR_umask		 60
-#define __NR_chroot		 61
-#define __NR_ustat		 62
-#define __NR_dup2		 63
-#define __NR_getppid		 64
-#define __NR_getpgrp		 65
-#define __NR_setsid		 66
-#define __NR_sigaction		 67
-#define __NR_sgetmask		 68
-#define __NR_ssetmask		 69
-#define __NR_setreuid		 70
-#define __NR_setregid		 71
-#define __NR_sigsuspend		 72
-#define __NR_sigpending		 73
-#define __NR_sethostname	 74
-#define __NR_setrlimit		 75
-#define __NR_getrlimit		 76
-#define __NR_getrusage		 77
-#define __NR_gettimeofday	 78
-#define __NR_settimeofday	 79
-#define __NR_getgroups		 80
-#define __NR_setgroups		 81
-#define __NR_select		 82
-#define __NR_symlink		 83
-#define __NR_oldlstat		 84
-#define __NR_readlink		 85
-#define __NR_uselib		 86
-#define __NR_swapon		 87
-#define __NR_reboot		 88
-#define __NR_readdir		 89
-#define __NR_mmap		 90
-#define __NR_munmap		 91
-#define __NR_truncate		 92
-#define __NR_ftruncate		 93
-#define __NR_fchmod		 94
-#define __NR_fchown		 95
-#define __NR_getpriority	 96
-#define __NR_setpriority	 97
-/*#define __NR_profil		 98*/
-#define __NR_statfs		 99
-#define __NR_fstatfs		100
-/*#define __NR_ioperm		101*/
-#define __NR_socketcall		102
-#define __NR_syslog		103
-#define __NR_setitimer		104
-#define __NR_getitimer		105
-#define __NR_stat		106
-#define __NR_lstat		107
-#define __NR_fstat		108
-/*#define __NR_olduname		109*/
-/*#define __NR_iopl		110*/ /* not supported */
-#define __NR_vhangup		111
-/*#define __NR_idle		112*/ /* Obsolete */
-/*#define __NR_vm86		113*/ /* not supported */
-#define __NR_wait4		114
-#define __NR_swapoff		115
-#define __NR_sysinfo		116
-#define __NR_ipc		117
-#define __NR_fsync		118
-#define __NR_sigreturn		119
-#define __NR_clone		120
-#define __NR_setdomainname	121
-#define __NR_uname		122
-#define __NR_cacheflush		123
-#define __NR_adjtimex		124
-#define __NR_mprotect		125
-#define __NR_sigprocmask	126
-#define __NR_create_module	127
-#define __NR_init_module	128
-#define __NR_delete_module	129
-#define __NR_get_kernel_syms	130
-#define __NR_quotactl		131
-#define __NR_getpgid		132
-#define __NR_fchdir		133
-#define __NR_bdflush		134
-#define __NR_sysfs		135
-#define __NR_personality	136
-/*#define __NR_afs_syscall	137*/ /* Syscall for Andrew File System */
-#define __NR_setfsuid		138
-#define __NR_setfsgid		139
-#define __NR__llseek		140
-#define __NR_getdents		141
-#define __NR__newselect		142
-#define __NR_flock		143
-#define __NR_msync		144
-#define __NR_readv		145
-#define __NR_writev		146
-#define __NR_getsid		147
-#define __NR_fdatasync		148
-#define __NR__sysctl		149
-#define __NR_mlock		150
-#define __NR_munlock		151
-#define __NR_mlockall		152
-#define __NR_munlockall		153
-#define __NR_sched_setparam		154
-#define __NR_sched_getparam		155
-#define __NR_sched_setscheduler		156
-#define __NR_sched_getscheduler		157
-#define __NR_sched_yield		158
-#define __NR_sched_get_priority_max	159
-#define __NR_sched_get_priority_min	160
-#define __NR_sched_rr_get_interval	161
-#define __NR_nanosleep		162
-#define __NR_mremap		163
-#define __NR_setresuid		164
-#define __NR_getresuid		165
-#define __NR_getpagesize	166
-#define __NR_query_module	167
-#define __NR_poll		168
-#define __NR_nfsservctl		169
-#define __NR_setresgid		170
-#define __NR_getresgid		171
-#define __NR_prctl		172
-#define __NR_rt_sigreturn	173
-#define __NR_rt_sigaction	174
-#define __NR_rt_sigprocmask	175
-#define __NR_rt_sigpending	176
-#define __NR_rt_sigtimedwait	177
-#define __NR_rt_sigqueueinfo	178
-#define __NR_rt_sigsuspend	179
-#define __NR_pread64		180
-#define __NR_pwrite64		181
-#define __NR_lchown		182
-#define __NR_getcwd		183
-#define __NR_capget		184
-#define __NR_capset		185
-#define __NR_sigaltstack	186
-#define __NR_sendfile		187
-#define __NR_getpmsg		188	/* some people actually want streams */
-#define __NR_putpmsg		189	/* some people actually want streams */
-#define __NR_vfork		190
-#define __NR_ugetrlimit		191
-#define __NR_mmap2		192
-#define __NR_truncate64		193
-#define __NR_ftruncate64	194
-#define __NR_stat64		195
-#define __NR_lstat64		196
-#define __NR_fstat64		197
-#define __NR_chown32		198
-#define __NR_getuid32		199
-#define __NR_getgid32		200
-#define __NR_geteuid32		201
-#define __NR_getegid32		202
-#define __NR_setreuid32		203
-#define __NR_setregid32		204
-#define __NR_getgroups32	205
-#define __NR_setgroups32	206
-#define __NR_fchown32		207
-#define __NR_setresuid32	208
-#define __NR_getresuid32	209
-#define __NR_setresgid32	210
-#define __NR_getresgid32	211
-#define __NR_lchown32		212
-#define __NR_setuid32		213
-#define __NR_setgid32		214
-#define __NR_setfsuid32		215
-#define __NR_setfsgid32		216
-#define __NR_pivot_root		217
-/* 218*/
-/* 219*/
-#define __NR_getdents64		220
-#define __NR_gettid		221
-#define __NR_tkill		222
-#define __NR_setxattr		223
-#define __NR_lsetxattr		224
-#define __NR_fsetxattr		225
-#define __NR_getxattr		226
-#define __NR_lgetxattr		227
-#define __NR_fgetxattr		228
-#define __NR_listxattr		229
-#define __NR_llistxattr		230
-#define __NR_flistxattr		231
-#define __NR_removexattr	232
-#define __NR_lremovexattr	233
-#define __NR_fremovexattr	234
-#define __NR_futex		235
-#define __NR_sendfile64		236
-#define __NR_mincore		237
-#define __NR_madvise		238
-#define __NR_fcntl64		239
-#define __NR_readahead		240
-#define __NR_io_setup		241
-#define __NR_io_destroy		242
-#define __NR_io_getevents	243
-#define __NR_io_submit		244
-#define __NR_io_cancel		245
-#define __NR_fadvise64		246
-#define __NR_exit_group		247
-#define __NR_lookup_dcookie	248
-#define __NR_epoll_create	249
-#define __NR_epoll_ctl		250
-#define __NR_epoll_wait		251
-#define __NR_remap_file_pages	252
-#define __NR_set_tid_address	253
-#define __NR_timer_create	254
-#define __NR_timer_settime	255
-#define __NR_timer_gettime	256
-#define __NR_timer_getoverrun	257
-#define __NR_timer_delete	258
-#define __NR_clock_settime	259
-#define __NR_clock_gettime	260
-#define __NR_clock_getres	261
-#define __NR_clock_nanosleep	262
-#define __NR_statfs64		263
-#define __NR_fstatfs64		264
-#define __NR_tgkill		265
-#define __NR_utimes		266
-#define __NR_fadvise64_64	267
-#define __NR_mbind		268
-#define __NR_get_mempolicy	269
-#define __NR_set_mempolicy	270
-#define __NR_mq_open		271
-#define __NR_mq_unlink		272
-#define __NR_mq_timedsend	273
-#define __NR_mq_timedreceive	274
-#define __NR_mq_notify		275
-#define __NR_mq_getsetattr	276
-#define __NR_waitid		277
-/*#define __NR_vserver		278*/
-#define __NR_add_key		279
-#define __NR_request_key	280
-#define __NR_keyctl		281
-#define __NR_ioprio_set		282
-#define __NR_ioprio_get		283
-#define __NR_inotify_init	284
-#define __NR_inotify_add_watch	285
-#define __NR_inotify_rm_watch	286
-#define __NR_migrate_pages	287
-#define __NR_openat		288
-#define __NR_mkdirat		289
-#define __NR_mknodat		290
-#define __NR_fchownat		291
-#define __NR_futimesat		292
-#define __NR_fstatat64		293
-#define __NR_unlinkat		294
-#define __NR_renameat		295
-#define __NR_linkat		296
-#define __NR_symlinkat		297
-#define __NR_readlinkat		298
-#define __NR_fchmodat		299
-#define __NR_faccessat		300
-#define __NR_pselect6		301
-#define __NR_ppoll		302
-#define __NR_unshare		303
-#define __NR_set_robust_list	304
-#define __NR_get_robust_list	305
-#define __NR_splice		306
-#define __NR_sync_file_range	307
-#define __NR_tee		308
-#define __NR_vmsplice		309
-#define __NR_move_pages		310
-#define __NR_sched_setaffinity	311
-#define __NR_sched_getaffinity	312
-#define __NR_kexec_load		313
-#define __NR_getcpu		314
-#define __NR_epoll_pwait	315
-#define __NR_utimensat		316
-#define __NR_signalfd		317
-#define __NR_timerfd_create	318
-#define __NR_eventfd		319
-#define __NR_fallocate		320
-#define __NR_timerfd_settime	321
-#define __NR_timerfd_gettime	322
-#define __NR_signalfd4		323
-#define __NR_eventfd2		324
-#define __NR_epoll_create1	325
-#define __NR_dup3		326
-#define __NR_pipe2		327
-#define __NR_inotify_init1	328
-#define __NR_preadv		329
-#define __NR_pwritev		330
-#define __NR_rt_tgsigqueueinfo	331
-#define __NR_perf_event_open	332
-#define __NR_get_thread_area	333
-#define __NR_set_thread_area	334
-#define __NR_atomic_cmpxchg_32	335
-#define __NR_atomic_barrier	336
-#define __NR_fanotify_init	337
-#define __NR_fanotify_mark	338
-#define __NR_prlimit64		339
-#define __NR_name_to_handle_at	340
-#define __NR_open_by_handle_at	341
-#define __NR_clock_adjtime	342
-#define __NR_syncfs		343
-#define __NR_setns		344
-#define __NR_process_vm_readv	345
-#define __NR_process_vm_writev	346
 
-#ifdef __KERNEL__
+#define NR_syscalls		348
-
-#define NR_syscalls		347
 
 #define __ARCH_WANT_OLD_READDIR
 #define __ARCH_WANT_OLD_STAT
@@ -393,5 +42,4 @@
  */
 #define cond_syscall(x) asm(".weak\t" #x "\n\t.set\t" #x ",sys_ni_syscall")
 
-#endif /* __KERNEL__ */
 #endif /* _ASM_M68K_UNISTD_H_ */

arch/m68k/include/uapi/asm/Kbuild

@@ -1,3 +1,26 @@
 # UAPI Header export list
 include include/uapi/asm-generic/Kbuild.asm
 
+header-y += a.out.h
+header-y += auxvec.h
+header-y += byteorder.h
+header-y += cachectl.h
+header-y += fcntl.h
+header-y += ioctls.h
+header-y += msgbuf.h
+header-y += param.h
+header-y += poll.h
+header-y += posix_types.h
+header-y += ptrace.h
+header-y += sembuf.h
+header-y += setup.h
+header-y += shmbuf.h
+header-y += sigcontext.h
+header-y += signal.h
+header-y += socket.h
+header-y += sockios.h
+header-y += stat.h
+header-y += swab.h
+header-y += termbits.h
+header-y += termios.h
+header-y += unistd.h