[SCSI] scsi: remove Documentation/scsi/cpqfc.txt
cpqfc driver flushed out with: [SCSI] remove broken driver cpqfc (commit
ca61f10ab2) but somehow
Documentation/scsi/cpqfc.txt managed to survive the blast.
Signed-off-by: Arthur Othieno <apgo@patchbomb.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This commit is contained in:
Arthur Othieno
James Bottomley
parent
6391a11375
commit
b9f051eb6c
|
|
@ -30,8 +30,6 @@ aic7xxx.txt
|
|||
- info on driver for Adaptec controllers
|
||||
aic7xxx_old.txt
|
||||
- info on driver for Adaptec controllers, old generation
|
||||
cpqfc.txt
|
||||
- info on driver for Compaq Tachyon TS adapters
|
||||
dpti.txt
|
||||
- info on driver for DPT SmartRAID and Adaptec I2O RAID based adapters
|
||||
dtc3x80.txt
|
||||
|
|
|
|||
|
|
@ -1,272 +0,0 @@
|
|||
Notes for CPQFCTS driver for Compaq Tachyon TS
|
||||
Fibre Channel Host Bus Adapter, PCI 64-bit, 66MHz
|
||||
for Linux (RH 6.1, 6.2 kernel 2.2.12-32, 2.2.14-5)
|
||||
SMP tested
|
||||
Tested in single and dual HBA configuration, 32 and 64bit busses,
|
||||
33 and 66MHz. Only supports FC-AL.
|
||||
SEST size 512 Exchanges (simultaneous I/Os) limited by module kmalloc()
|
||||
max of 128k bytes contiguous.
|
||||
|
||||
Ver 2.5.4 Oct 03, 2002
|
||||
* fixed memcpy of sense buffer in ioctl to copy the smaller defined size
|
||||
Ver 2.5.3 Aug 01, 2002
|
||||
* fix the passthru ioctl to handle the Scsi_Cmnd->request being a pointer
|
||||
Ver 2.5.1 Jul 30, 2002
|
||||
* fix ioctl to pay attention to the specified LUN.
|
||||
Ver 2.5.0 Nov 29, 2001
|
||||
* eliminated io_request_lock. This change makes the driver specific
|
||||
to the 2.5.x kernels.
|
||||
* silenced excessively noisy printks.
|
||||
|
||||
Ver 2.1.2 July 23, 2002
|
||||
* initialize DumCmnd->lun in cpqfcTS_ioctl (used in fcFindLoggedInPorts as LUN index)
|
||||
|
||||
Ver 2.1.1 Oct 18, 2001
|
||||
* reinitialize Cmnd->SCp.sent_command (used to identify commands as
|
||||
passthrus) on calling scsi_done, since the scsi mid layer does not
|
||||
use (or reinitialize) this field to prevent subsequent comands from
|
||||
having it set incorrectly.
|
||||
|
||||
Ver 2.1.0 Aug 27, 2001
|
||||
* Revise driver to use new kernel 2.4.x PCI DMA API, instead of
|
||||
virt_to_bus(). (enables driver to work w/ ia64 systems with >2Gb RAM.)
|
||||
Rework main scatter-gather code to handle cases where SG element
|
||||
lengths are larger than 0x7FFFF bytes and use as many scatter
|
||||
gather pages as necessary. (Steve Cameron)
|
||||
* Makefile changes to bring cpqfc into line w/ rest of SCSI drivers
|
||||
(thanks to Keith Owens)
|
||||
|
||||
Ver 2.0.5 Aug 06, 2001
|
||||
* Reject non-existent luns in the driver rather than letting the
|
||||
hardware do it. (some HW behaves differently than others in this area.)
|
||||
* Changed Makefile to rely on "make dep" instead of explicit dependencies
|
||||
* ifdef'ed out fibre channel analyzer triggering debug code
|
||||
* fixed a jiffies wrapping issue
|
||||
|
||||
Ver 2.0.4 Aug 01, 2001
|
||||
* Incorporated fix for target device reset from Steeleye
|
||||
* Fixed passthrough ioctl so it doesn't hang.
|
||||
* Fixed hang in launch_FCworker_thread() that occurred on some machines.
|
||||
* Avoid problem when number of volumes in a single cabinet > 8
|
||||
|
||||
Ver 2.0.2 July 23, 2001
|
||||
Changed the semiphore changes so the driver would compile in 2.4.7.
|
||||
This version is for 2.4.7 and beyond.
|
||||
|
||||
Ver 2.0.1 May 7, 2001
|
||||
Merged version 1.3.6 fixes into version 2.0.0.
|
||||
|
||||
Ver 2.0.0 May 7, 2001
|
||||
Fixed problem so spinlock is being initialized to UNLOCKED.
|
||||
Fixed updated driver so it compiles in the 2.4 tree.
|
||||
|
||||
Ver 1.3.6 Feb 27, 2001
|
||||
Added Target_Device_Reset function for SCSI error handling
|
||||
Fixed problem with not reseting addressing mode after implicit logout
|
||||
|
||||
|
||||
Ver 1.3.4 Sep 7, 2000
|
||||
Added Modinfo information
|
||||
Fixed problem with statically linking the driver
|
||||
|
||||
Ver 1.3.3, Aug 23, 2000
|
||||
Fixed device/function number in ioctl
|
||||
|
||||
Ver 1.3.2, July 27, 2000
|
||||
Add include for Alpha compile on 2.2.14 kernel (cpq*i2c.c)
|
||||
Change logic for different FCP-RSP sense_buffer location for HSG80 target
|
||||
And search for Agilent Tachyon XL2 HBAs (not finished! - in test)
|
||||
|
||||
Tested with
|
||||
(storage):
|
||||
Compaq RA-4x000, RAID firmware ver 2.40 - 2.54
|
||||
Seagate FC drives model ST39102FC, rev 0006
|
||||
Hitachi DK31CJ-72FC rev J8A8
|
||||
IBM DDYF-T18350R rev F60K
|
||||
Compaq FC-SCSI bridge w/ DLT 35/70 Gb DLT (tape)
|
||||
(servers):
|
||||
Compaq PL-1850R
|
||||
Compaq PL-6500 Xeon (400MHz)
|
||||
Compaq PL-8500 (500MHz, 66MHz, 64bit PCI)
|
||||
Compaq Alpha DS20 (RH 6.1)
|
||||
(hubs):
|
||||
Vixel Rapport 1000 (7-port "dumb")
|
||||
Gadzoox Gibralter (12-port "dumb")
|
||||
Gadzoox Capellix 2000, 3000
|
||||
(switches):
|
||||
Brocade 2010, 2400, 2800, rev 2.0.3a (& later)
|
||||
Gadzoox 3210 (Fabric blade beta)
|
||||
Vixel 7100 (Fabric beta firmare - known hot plug issues)
|
||||
using "qa_test" (esp. io_test script) suite modified from Unix tests.
|
||||
|
||||
Installation:
|
||||
make menuconfig
|
||||
(select SCSI low-level, Compaq FC HBA)
|
||||
make modules
|
||||
make modules_install
|
||||
|
||||
e.g. insmod -f cpqfc
|
||||
|
||||
Due to Fabric/switch delays, driver requires 4 seconds
|
||||
to initialize. If adapters are found, there will be a entries at
|
||||
/proc/scsi/cpqfcTS/*
|
||||
|
||||
sample contents of startup messages
|
||||
|
||||
*************************
|
||||
scsi_register allocating 3596 bytes for CPQFCHBA
|
||||
ioremap'd Membase: c887e600
|
||||
HBA Tachyon RevId 1.2
|
||||
Allocating 119808 for 576 Exchanges @ c0dc0000
|
||||
Allocating 112904 for LinkQ @ c0c20000 (576 elements)
|
||||
Allocating 110600 for TachSEST for 512 Exchanges
|
||||
cpqfcTS: writing IMQ BASE 7C0000h PI 7C4000h
|
||||
cpqfcTS: SEST c0e40000(virt): Wrote base E40000h @ c887e740
|
||||
cpqfcTS: New FC port 0000E8h WWN: 500507650642499D SCSI Chan/Trgt 0/0
|
||||
cpqfcTS: New FC port 0000EFh WWN: 50000E100000D5A6 SCSI Chan/Trgt 0/1
|
||||
cpqfcTS: New FC port 0000E4h WWN: 21000020370097BB SCSI Chan/Trgt 0/2
|
||||
cpqfcTS: New FC port 0000E2h WWN: 2100002037009946 SCSI Chan/Trgt 0/3
|
||||
cpqfcTS: New FC port 0000E1h WWN: 21000020370098FE SCSI Chan/Trgt 0/4
|
||||
cpqfcTS: New FC port 0000E0h WWN: 21000020370097B2 SCSI Chan/Trgt 0/5
|
||||
cpqfcTS: New FC port 0000DCh WWN: 2100002037006CC1 SCSI Chan/Trgt 0/6
|
||||
cpqfcTS: New FC port 0000DAh WWN: 21000020370059F6 SCSI Chan/Trgt 0/7
|
||||
cpqfcTS: New FC port 00000Fh WWN: 500805F1FADB0E20 SCSI Chan/Trgt 0/8
|
||||
cpqfcTS: New FC port 000008h WWN: 500805F1FADB0EBA SCSI Chan/Trgt 0/9
|
||||
cpqfcTS: New FC port 000004h WWN: 500805F1FADB1EB9 SCSI Chan/Trgt 0/10
|
||||
cpqfcTS: New FC port 000002h WWN: 500805F1FADB1ADE SCSI Chan/Trgt 0/11
|
||||
cpqfcTS: New FC port 000001h WWN: 500805F1FADBA2CA SCSI Chan/Trgt 0/12
|
||||
scsi4 : Compaq FibreChannel HBA Tachyon TS HPFC-5166A/1.2: WWN 500508B200193F50
|
||||
on PCI bus 0 device 0xa0fc irq 5 IObaseL 0x3400, MEMBASE 0xc6ef8600
|
||||
PCI bus width 32 bits, bus speed 33 MHz
|
||||
FCP-SCSI Driver v1.3.0
|
||||
GBIC detected: Short-wave. LPSM 0h Monitor
|
||||
scsi : 5 hosts.
|
||||
Vendor: IBM Model: DDYF-T18350R Rev: F60K
|
||||
Type: Direct-Access ANSI SCSI revision: 03
|
||||
Detected scsi disk sdb at scsi4, channel 0, id 0, lun 0
|
||||
Vendor: HITACHI Model: DK31CJ-72FC Rev: J8A8
|
||||
Type: Direct-Access ANSI SCSI revision: 02
|
||||
Detected scsi disk sdc at scsi4, channel 0, id 1, lun 0
|
||||
Vendor: SEAGATE Model: ST39102FC Rev: 0006
|
||||
Type: Direct-Access ANSI SCSI revision: 02
|
||||
Detected scsi disk sdd at scsi4, channel 0, id 2, lun 0
|
||||
Vendor: SEAGATE Model: ST39102FC Rev: 0006
|
||||
Type: Direct-Access ANSI SCSI revision: 02
|
||||
Detected scsi disk sde at scsi4, channel 0, id 3, lun 0
|
||||
Vendor: SEAGATE Model: ST39102FC Rev: 0006
|
||||
Type: Direct-Access ANSI SCSI revision: 02
|
||||
Detected scsi disk sdf at scsi4, channel 0, id 4, lun 0
|
||||
Vendor: SEAGATE Model: ST39102FC Rev: 0006
|
||||
Type: Direct-Access ANSI SCSI revision: 02
|
||||
Detected scsi disk sdg at scsi4, channel 0, id 5, lun 0
|
||||
Vendor: SEAGATE Model: ST39102FC Rev: 0006
|
||||
Type: Direct-Access ANSI SCSI revision: 02
|
||||
Detected scsi disk sdh at scsi4, channel 0, id 6, lun 0
|
||||
Vendor: SEAGATE Model: ST39102FC Rev: 0006
|
||||
Type: Direct-Access ANSI SCSI revision: 02
|
||||
Detected scsi disk sdi at scsi4, channel 0, id 7, lun 0
|
||||
Vendor: COMPAQ Model: LOGICAL VOLUME Rev: 2.48
|
||||
Type: Direct-Access ANSI SCSI revision: 02
|
||||
Detected scsi disk sdj at scsi4, channel 0, id 8, lun 0
|
||||
Vendor: COMPAQ Model: LOGICAL VOLUME Rev: 2.48
|
||||
Type: Direct-Access ANSI SCSI revision: 02
|
||||
Detected scsi disk sdk at scsi4, channel 0, id 8, lun 1
|
||||
Vendor: COMPAQ Model: LOGICAL VOLUME Rev: 2.40
|
||||
Type: Direct-Access ANSI SCSI revision: 02
|
||||
Detected scsi disk sdl at scsi4, channel 0, id 9, lun 0
|
||||
Vendor: COMPAQ Model: LOGICAL VOLUME Rev: 2.40
|
||||
Type: Direct-Access ANSI SCSI revision: 02
|
||||
Detected scsi disk sdm at scsi4, channel 0, id 9, lun 1
|
||||
Vendor: COMPAQ Model: LOGICAL VOLUME Rev: 2.54
|
||||
Type: Direct-Access ANSI SCSI revision: 02
|
||||
Detected scsi disk sdn at scsi4, channel 0, id 10, lun 0
|
||||
Vendor: COMPAQ Model: LOGICAL VOLUME Rev: 2.54
|
||||
Type: Direct-Access ANSI SCSI revision: 02
|
||||
Detected scsi disk sdo at scsi4, channel 0, id 11, lun 0
|
||||
Vendor: COMPAQ Model: LOGICAL VOLUME Rev: 2.54
|
||||
Type: Direct-Access ANSI SCSI revision: 02
|
||||
Detected scsi disk sdp at scsi4, channel 0, id 11, lun 1
|
||||
Vendor: COMPAQ Model: LOGICAL VOLUME Rev: 2.54
|
||||
Type: Direct-Access ANSI SCSI revision: 02
|
||||
Detected scsi disk sdq at scsi4, channel 0, id 12, lun 0
|
||||
Vendor: COMPAQ Model: LOGICAL VOLUME Rev: 2.54
|
||||
Type: Direct-Access ANSI SCSI revision: 02
|
||||
Detected scsi disk sdr at scsi4, channel 0, id 12, lun 1
|
||||
resize_dma_pool: unknown device type 12
|
||||
resize_dma_pool: unknown device type 12
|
||||
SCSI device sdb: hdwr sector= 512 bytes. Sectors= 35843670 [17501 MB] [17.5 GB]
|
||||
sdb: sdb1
|
||||
SCSI device sdc: hdwr sector= 512 bytes. Sectors= 144410880 [70513 MB] [70.5 GB]
|
||||
sdc: sdc1
|
||||
SCSI device sdd: hdwr sector= 512 bytes. Sectors= 17783240 [8683 MB] [8.7 GB]
|
||||
sdd: sdd1
|
||||
SCSI device sde: hdwr sector= 512 bytes. Sectors= 17783240 [8683 MB] [8.7 GB]
|
||||
sde: sde1
|
||||
SCSI device sdf: hdwr sector= 512 bytes. Sectors= 17783240 [8683 MB] [8.7 GB]
|
||||
sdf: sdf1
|
||||
SCSI device sdg: hdwr sector= 512 bytes. Sectors= 17783240 [8683 MB] [8.7 GB]
|
||||
sdg: sdg1
|
||||
SCSI device sdh: hdwr sector= 512 bytes. Sectors= 17783240 [8683 MB] [8.7 GB]
|
||||
sdh: sdh1
|
||||
SCSI device sdi: hdwr sector= 512 bytes. Sectors= 17783240 [8683 MB] [8.7 GB]
|
||||
sdi: sdi1
|
||||
SCSI device sdj: hdwr sector= 512 bytes. Sectors= 2056160 [1003 MB] [1.0 GB]
|
||||
sdj: sdj1
|
||||
SCSI device sdk: hdwr sector= 512 bytes. Sectors= 2052736 [1002 MB] [1.0 GB]
|
||||
sdk: sdk1
|
||||
SCSI device sdl: hdwr sector= 512 bytes. Sectors= 17764320 [8673 MB] [8.7 GB]
|
||||
sdl: sdl1
|
||||
SCSI device sdm: hdwr sector= 512 bytes. Sectors= 8380320 [4091 MB] [4.1 GB]
|
||||
sdm: sdm1
|
||||
SCSI device sdn: hdwr sector= 512 bytes. Sectors= 17764320 [8673 MB] [8.7 GB]
|
||||
sdn: sdn1
|
||||
SCSI device sdo: hdwr sector= 512 bytes. Sectors= 17764320 [8673 MB] [8.7 GB]
|
||||
sdo: sdo1
|
||||
SCSI device sdp: hdwr sector= 512 bytes. Sectors= 17764320 [8673 MB] [8.7 GB]
|
||||
sdp: sdp1
|
||||
SCSI device sdq: hdwr sector= 512 bytes. Sectors= 2056160 [1003 MB] [1.0 GB]
|
||||
sdq: sdq1
|
||||
SCSI device sdr: hdwr sector= 512 bytes. Sectors= 2052736 [1002 MB] [1.0 GB]
|
||||
sdr: sdr1
|
||||
|
||||
*************************
|
||||
|
||||
If a GBIC of type Short-wave, Long-wave, or Copper is detected, it will
|
||||
print out; otherwise, "none" is displayed. If the cabling is correct
|
||||
and a loop circuit is completed, you should see "Monitor"; otherwise,
|
||||
"LoopFail" (on open circuit) or some LPSM number/state with bit 3 set.
|
||||
|
||||
|
||||
ERRATA:
|
||||
1. Normally, Linux Scsi queries FC devices with INQUIRY strings. All LUNs
|
||||
found according to INQUIRY should get READ commands at sector 0 to find
|
||||
partition table, etc. Older kernels only query the first 4 devices. Some
|
||||
Linux kernels only look for one LUN per target (i.e. FC device).
|
||||
|
||||
2. Physically removing a device, or a malfunctioning system which hides a
|
||||
device, leads to a 30-second timeout and subsequent _abort call.
|
||||
In some process contexts, this will hang the kernel (crashing the system).
|
||||
Single bit errors in frames and virtually all hot plugging events are
|
||||
gracefully handled with internal driver timer and Abort processing.
|
||||
|
||||
3. Some SCSI drives with error conditions will not handle the 7 second timeout
|
||||
in this software driver, leading to infinite retries on timed out SCSI commands.
|
||||
The 7 secs balances the need to quickly recover from lost frames (esp. on sequence
|
||||
initiatives) and time needed by older/slower/error-state drives in responding.
|
||||
This can be easily changed in "Exchanges[].timeOut".
|
||||
|
||||
4. Due to the nature of FC soft addressing, there is no assurance that the
|
||||
same LUNs (drives) will have the same path (e.g. /dev/sdb1) from one boot to
|
||||
next. Dynamic soft address changes (i.e. 24-bit FC port_id) are
|
||||
supported during run time (e.g. due to hot plug event) by the use of WWN to
|
||||
SCSI Nexus (channel/target/LUN) mapping.
|
||||
|
||||
5. Compaq RA4x00 firmware version 2.54 and later supports SSP (Selective
|
||||
Storage Presentation), which maps LUNs to a WWN. If RA4x00 firmware prior
|
||||
2.54 (e.g. older controller) is used, or the FC HBA is replaced (another WWN
|
||||
is used), logical volumes on the RA4x00 will no longer be visible.
|
||||
|
||||
|
||||
Send questions/comments to:
|
||||
Amy Vanzant-Hodge (fibrechannel@compaq.com)
|
||||
|
||||
Loading…
Reference in New Issue