From b422d1b6f761bf336e0219fee6901481d33453a0 Mon Sep 17 00:00:00 2001 From: Alexandru Ardelean Date: Fri, 16 Aug 2019 16:10:06 +0300 Subject: [PATCH] net: phy: adin: add support MDI/MDIX/Auto-MDI selection The ADIN PHYs support automatic MDI/MDIX negotiation. By default this is disabled, so this is enabled at `config_init`. This is controlled via the PHY Control 1 register. The supported modes are: 1. Manual MDI 2. Manual MDIX 3. Auto MDIX - prefer MDIX 4. Auto MDIX - prefer MDI The phydev mdix & mdix_ctrl fields include modes 3 & 4 into a single auto-mode. So, the default mode this driver enables is 4 when Auto-MDI mode is used. When detecting MDI/MDIX mode, a combination of the PHY Control 1 register and PHY Status 1 register is used to determine the correct MDI/MDIX mode. If Auto-MDI mode is not set, then the manual MDI/MDIX mode is returned. If Auto-MDI mode is set, then MDIX mode is returned differs from the preferred MDI/MDIX mode. This covers all cases where: 1. MDI preferred & Pair01Swapped == MDIX 2. MDIX preferred & Pair01Swapped == MDI 3. MDI preferred & ! Pair01Swapped == MDIX 4. MDIX preferred & ! Pair01Swapped == MDI The preferred MDI/MDIX mode is not configured via SW, but can be configured via HW pins. Note that the `Pair01Swapped` is the Green-Yellow physical pairs. Reviewed-by: Florian Fainelli Signed-off-by: Alexandru Ardelean Signed-off-by: David S. Miller --- drivers/net/phy/adin.c | 117 +++++++++++++++++++++++++++++++++++++++-- 1 file changed, 113 insertions(+), 4 deletions(-) diff --git a/drivers/net/phy/adin.c b/drivers/net/phy/adin.c index 4ca685780622..51c0d17577de 100644 --- a/drivers/net/phy/adin.c +++ b/drivers/net/phy/adin.c @@ -19,6 +19,10 @@ #define ADIN1300_MII_EXT_REG_PTR 0x0010 #define ADIN1300_MII_EXT_REG_DATA 0x0011 +#define ADIN1300_PHY_CTRL1 0x0012 +#define ADIN1300_AUTO_MDI_EN BIT(10) +#define ADIN1300_MAN_MDIX_EN BIT(9) + #define ADIN1300_INT_MASK_REG 0x0018 #define ADIN1300_INT_MDIO_SYNC_EN BIT(9) #define ADIN1300_INT_ANEG_STAT_CHNG_EN BIT(8) @@ -33,6 +37,9 @@ (ADIN1300_INT_LINK_STAT_CHNG_EN | ADIN1300_INT_HW_IRQ_EN) #define ADIN1300_INT_STATUS_REG 0x0019 +#define ADIN1300_PHY_STATUS1 0x001a +#define ADIN1300_PAIR_01_SWAP BIT(11) + #define ADIN1300_GE_RGMII_CFG_REG 0xff23 #define ADIN1300_GE_RGMII_RX_MSK GENMASK(8, 6) #define ADIN1300_GE_RGMII_RX_SEL(x) \ @@ -206,6 +213,8 @@ static int adin_config_init(struct phy_device *phydev) { int rc; + phydev->mdix_ctrl = ETH_TP_MDI_AUTO; + rc = genphy_config_init(phydev); if (rc < 0) return rc; @@ -269,13 +278,113 @@ static int adin_write_mmd(struct phy_device *phydev, int devad, u16 regnum, return __mdiobus_write(bus, phy_addr, ADIN1300_MII_EXT_REG_DATA, val); } +static int adin_config_mdix(struct phy_device *phydev) +{ + bool auto_en, mdix_en; + int reg; + + mdix_en = false; + auto_en = false; + switch (phydev->mdix_ctrl) { + case ETH_TP_MDI: + break; + case ETH_TP_MDI_X: + mdix_en = true; + break; + case ETH_TP_MDI_AUTO: + auto_en = true; + break; + default: + return -EINVAL; + } + + reg = phy_read(phydev, ADIN1300_PHY_CTRL1); + if (reg < 0) + return reg; + + if (mdix_en) + reg |= ADIN1300_MAN_MDIX_EN; + else + reg &= ~ADIN1300_MAN_MDIX_EN; + + if (auto_en) + reg |= ADIN1300_AUTO_MDI_EN; + else + reg &= ~ADIN1300_AUTO_MDI_EN; + + return phy_write(phydev, ADIN1300_PHY_CTRL1, reg); +} + +static int adin_config_aneg(struct phy_device *phydev) +{ + int ret; + + ret = adin_config_mdix(phydev); + if (ret) + return ret; + + return genphy_config_aneg(phydev); +} + +static int adin_mdix_update(struct phy_device *phydev) +{ + bool auto_en, mdix_en; + bool swapped; + int reg; + + reg = phy_read(phydev, ADIN1300_PHY_CTRL1); + if (reg < 0) + return reg; + + auto_en = !!(reg & ADIN1300_AUTO_MDI_EN); + mdix_en = !!(reg & ADIN1300_MAN_MDIX_EN); + + /* If MDI/MDIX is forced, just read it from the control reg */ + if (!auto_en) { + if (mdix_en) + phydev->mdix = ETH_TP_MDI_X; + else + phydev->mdix = ETH_TP_MDI; + return 0; + } + + /** + * Otherwise, we need to deduce it from the PHY status2 reg. + * When Auto-MDI is enabled, the ADIN1300_MAN_MDIX_EN bit implies + * a preference for MDIX when it is set. + */ + reg = phy_read(phydev, ADIN1300_PHY_STATUS1); + if (reg < 0) + return reg; + + swapped = !!(reg & ADIN1300_PAIR_01_SWAP); + + if (mdix_en != swapped) + phydev->mdix = ETH_TP_MDI_X; + else + phydev->mdix = ETH_TP_MDI; + + return 0; +} + +static int adin_read_status(struct phy_device *phydev) +{ + int ret; + + ret = adin_mdix_update(phydev); + if (ret < 0) + return ret; + + return genphy_read_status(phydev); +} + static struct phy_driver adin_driver[] = { { PHY_ID_MATCH_MODEL(PHY_ID_ADIN1200), .name = "ADIN1200", .config_init = adin_config_init, - .config_aneg = genphy_config_aneg, - .read_status = genphy_read_status, + .config_aneg = adin_config_aneg, + .read_status = adin_read_status, .ack_interrupt = adin_phy_ack_intr, .config_intr = adin_phy_config_intr, .resume = genphy_resume, @@ -287,8 +396,8 @@ static struct phy_driver adin_driver[] = { PHY_ID_MATCH_MODEL(PHY_ID_ADIN1300), .name = "ADIN1300", .config_init = adin_config_init, - .config_aneg = genphy_config_aneg, - .read_status = genphy_read_status, + .config_aneg = adin_config_aneg, + .read_status = adin_read_status, .ack_interrupt = adin_phy_ack_intr, .config_intr = adin_phy_config_intr, .resume = genphy_resume,