ARM: at91/dt: add support for kizboxmini
Add DT file for Kizbox mini board. This board is based on Atmel's AT91SAM9G25 SoC. Signed-off-by: Gaël PORTAY <g.portay@overkiz.com> Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com> Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com> Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
This commit is contained in:
parent
b76b7c2c40
commit
a9c0d1d277
|
@ -32,6 +32,7 @@ dtb-$(CONFIG_SOC_SAM_V4_V5) += \
|
|||
at91sam9rlek.dtb \
|
||||
at91-ariag25.dtb \
|
||||
at91-cosino_mega2560.dtb \
|
||||
at91-kizboxmini.dtb \
|
||||
at91sam9g15ek.dtb \
|
||||
at91sam9g25ek.dtb \
|
||||
at91sam9g35ek.dtb \
|
||||
|
|
|
@ -0,0 +1,129 @@
|
|||
/*
|
||||
* at91-kizboxmini.dts - Device Tree file for Overkiz Kizbox mini board
|
||||
*
|
||||
* Copyright (C) 2014 Gaël PORTAY <g.portay@overkiz.com>
|
||||
*
|
||||
* Licensed under GPLv2 or later.
|
||||
*/
|
||||
/dts-v1/;
|
||||
#include "at91sam9g25.dtsi"
|
||||
#include <dt-bindings/pwm/pwm.h>
|
||||
|
||||
/ {
|
||||
model = "Overkiz Kizbox mini";
|
||||
compatible = "overkiz,kizboxmini", "atmel,at91sam9g25", "atmel,at91sam9x5", "atmel,at91sam9";
|
||||
|
||||
chosen {
|
||||
bootargs = "ubi.mtd=ubi";
|
||||
linux,stdout-path = &dbgu;
|
||||
};
|
||||
|
||||
memory {
|
||||
reg = <0x20000000 0x8000000>;
|
||||
};
|
||||
|
||||
clocks {
|
||||
slow_xtal {
|
||||
clock-frequency = <32768>;
|
||||
};
|
||||
|
||||
main_xtal {
|
||||
clock-frequency = <12000000>;
|
||||
};
|
||||
};
|
||||
|
||||
ahb {
|
||||
apb {
|
||||
usart0: serial@f801c000 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
macb0: ethernet@f802c000 {
|
||||
phy-mode = "rmii";
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
pwm0: pwm@f8034000 {
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&pinctrl_pwm0_pwm0_1
|
||||
&pinctrl_pwm0_pwm1_1>;
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
dbgu: serial@fffff200 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
watchdog@fffffe40 {
|
||||
status = "okay";
|
||||
};
|
||||
};
|
||||
|
||||
usb0: ohci@00600000 {
|
||||
num-ports = <1>;
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
usb1: ehci@00700000 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
nand0: nand@40000000 {
|
||||
nand-bus-width = <8>;
|
||||
nand-ecc-mode = "hw";
|
||||
atmel,has-pmecc;
|
||||
atmel,pmecc-cap = <4>;
|
||||
atmel,pmecc-sector-size = <512>;
|
||||
nand-on-flash-bbt;
|
||||
status = "okay";
|
||||
|
||||
bootstrap@0 {
|
||||
label = "bootstrap";
|
||||
reg = <0x0 0x20000>;
|
||||
};
|
||||
|
||||
ubi@20000 {
|
||||
label = "ubi";
|
||||
reg = <0x20000 0x7fe0000>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
gpio_keys {
|
||||
compatible = "gpio-keys";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
|
||||
prog {
|
||||
label = "PB_PROG";
|
||||
gpios = <&pioC 17 GPIO_ACTIVE_LOW>;
|
||||
linux,code = <0x102>;
|
||||
gpio-key,wakeup;
|
||||
};
|
||||
|
||||
reset {
|
||||
label = "PB_RST";
|
||||
gpios = <&pioC 16 GPIO_ACTIVE_LOW>;
|
||||
linux,code = <0x100>;
|
||||
gpio-key,wakeup;
|
||||
};
|
||||
};
|
||||
|
||||
pwm_leds {
|
||||
compatible = "pwm-leds";
|
||||
|
||||
green {
|
||||
label = "pwm:green:user";
|
||||
pwms = <&pwm0 0 10000000 0>;
|
||||
max-brightness = <255>;
|
||||
linux,default-trigger = "default-on";
|
||||
};
|
||||
|
||||
red {
|
||||
label = "pwm:red:user";
|
||||
pwms = <&pwm0 1 10000000 0>;
|
||||
max-brightness = <255>;
|
||||
linux,default-trigger = "default-on";
|
||||
};
|
||||
};
|
||||
};
|
Loading…
Reference in New Issue