diff --git a/arch/arm/boot/dts/armada-385-linksys.dtsi b/arch/arm/boot/dts/armada-385-linksys.dtsi
index 2306c45685b1..481e4a36e26b 100644
--- a/arch/arm/boot/dts/armada-385-linksys.dtsi
+++ b/arch/arm/boot/dts/armada-385-linksys.dtsi
@@ -61,214 +61,6 @@
 			  MBUS_ID(0x09, 0x19) 0 0xf1100000 0x10000
 			  MBUS_ID(0x09, 0x15) 0 0xf1110000 0x10000
 			  MBUS_ID(0x0c, 0x04) 0 0xf1200000 0x100000>;
-
-		internal-regs {
-			i2c@11000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&i2c0_pins>;
-				status = "okay";
-
-				tmp421@4c {
-					compatible = "ti,tmp421";
-					reg = <0x4c>;
-				};
-
-				pca9635@68 {
-					#address-cells = <1>;
-					#size-cells = <0>;
-					compatible = "nxp,pca9635";
-					reg = <0x68>;
-				};
-			};
-
-			/* J10: VCC, NC, RX, NC, TX, GND  */
-			serial@12000 {
-				status = "okay";
-			};
-
-			ethernet@70000 {
-				status = "okay";
-				phy-mode = "rgmii-id";
-				buffer-manager = <&bm>;
-				bm,pool-long = <2>;
-				bm,pool-short = <3>;
-				fixed-link {
-					speed = <1000>;
-					full-duplex;
-				};
-			};
-
-			ethernet@34000 {
-				status = "okay";
-				phy-mode = "sgmii";
-				buffer-manager = <&bm>;
-				bm,pool-long = <0>;
-				bm,pool-short = <1>;
-				fixed-link {
-					speed = <1000>;
-					full-duplex;
-				};
-			};
-
-			mdio@72004 {
-				status = "okay";
-
-				switch@0 {
-					compatible = "marvell,mv88e6085";
-					#address-cells = <1>;
-					#size-cells = <0>;
-					reg = <0>;
-
-					ports {
-						#address-cells = <1>;
-						#size-cells = <0>;
-
-						port@0 {
-							reg = <0>;
-							label = "lan4";
-						};
-
-						port@1 {
-							reg = <1>;
-							label = "lan3";
-						};
-
-						port@2 {
-							reg = <2>;
-							label = "lan2";
-						};
-
-						port@3 {
-							reg = <3>;
-							label = "lan1";
-						};
-
-						port@4 {
-							reg = <4>;
-							label = "wan";
-						};
-
-						port@5 {
-							reg = <5>;
-							label = "cpu";
-							ethernet = <&eth2>;
-
-							fixed-link {
-								speed = <1000>;
-								full-duplex;
-							};
-						};
-					};
-				};
-			};
-
-			sata@a8000 {
-				status = "okay";
-			};
-
-			bm@c8000 {
-				status = "okay";
-			};
-
-			/* USB part of the eSATA/USB 2.0 port */
-			usb@58000 {
-				status = "okay";
-			};
-
-			usb3@f8000 {
-				status = "okay";
-				usb-phy = <&usb3_phy>;
-			};
-
-			flash@d0000 {
-				status = "okay";
-				num-cs = <1>;
-				marvell,nand-keep-config;
-				marvell,nand-enable-arbiter;
-				nand-on-flash-bbt;
-
-				partition@0 {
-					label = "u-boot";
-					reg = <0x0000000 0x200000>;  /* 2MB */
-					read-only;
-				};
-
-				partition@100000 {
-					label = "u_env";
-					reg = <0x200000 0x40000>;    /* 256KB */
-				};
-
-				partition@140000 {
-					label = "s_env";
-					reg = <0x240000 0x40000>;    /* 256KB */
-				};
-
-				partition@900000 {
-					label = "devinfo";
-					reg = <0x900000 0x100000>;   /* 1MB */
-					read-only;
-				};
-
-				/* kernel1 overlaps with rootfs1 by design */
-				partition@a00000 {
-					label = "kernel1";
-					reg = <0xa00000 0x2800000>;  /* 40MB */
-				};
-
-				partition@1000000 {
-					label = "rootfs1";
-					reg = <0x1000000 0x2200000>;  /* 34MB */
-				};
-
-				/* kernel2 overlaps with rootfs2 by design */
-				partition@3200000 {
-					label = "kernel2";
-					reg = <0x3200000 0x2800000>; /* 40MB */
-				};
-
-				partition@3800000 {
-					label = "rootfs2";
-					reg = <0x3800000 0x2200000>; /* 34MB */
-				};
-
-				/*
-				 * 38MB, last MB is for the BBT, not writable
-				 */
-				partition@5a00000 {
-					label = "syscfg";
-					reg = <0x5a00000 0x2600000>;
-				};
-
-				/*
-				 * Unused area between "s_env" and "devinfo".
-				 * Moved here because otherwise the renumbered
-				 * partitions would break the bootloader
-				 * supplied bootargs
-				 */
-				partition@180000 {
-					label = "unused_area";
-					reg = <0x280000 0x680000>;   /* 6.5MB */
-				};
-			};
-		};
-
-		bm-bppi {
-			status = "okay";
-		};
-
-		pcie-controller {
-			status = "okay";
-
-			pcie@1,0 {
-				/* Marvell 88W8864, 5GHz-only */
-				status = "okay";
-			};
-
-			pcie@2,0 {
-				/* Marvell 88W8864, 2GHz-only */
-				status = "okay";
-			};
-		};
 	};
 
 	usb3_phy: usb3_phy {
@@ -372,6 +164,197 @@
 	};
 };
 
+&ahci0 {
+	status = "okay";
+};
+
+&bm {
+	status = "okay";
+};
+
+&bm_bppi {
+	status = "okay";
+};
+
+&eth0 {
+	status = "okay";
+	phy-mode = "rgmii-id";
+	buffer-manager = <&bm>;
+	bm,pool-long = <2>;
+	bm,pool-short = <3>;
+	fixed-link {
+		speed = <1000>;
+		full-duplex;
+	};
+};
+
+&eth2 {
+	status = "okay";
+	phy-mode = "sgmii";
+	buffer-manager = <&bm>;
+	bm,pool-long = <0>;
+	bm,pool-short = <1>;
+	fixed-link {
+		speed = <1000>;
+		full-duplex;
+	};
+};
+
+&i2c0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c0_pins>;
+	status = "okay";
+
+	tmp421@4c {
+		compatible = "ti,tmp421";
+		reg = <0x4c>;
+	};
+
+	pca9635@68 {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		compatible = "nxp,pca9635";
+		reg = <0x68>;
+	};
+};
+
+&nand {
+	status = "okay";
+	num-cs = <1>;
+	marvell,nand-keep-config;
+	marvell,nand-enable-arbiter;
+	nand-on-flash-bbt;
+
+	partition@0 {
+		label = "u-boot";
+		reg = <0x0000000 0x200000>;  /* 2MB */
+		read-only;
+	};
+
+	partition@100000 {
+		label = "u_env";
+		reg = <0x200000 0x40000>;    /* 256KB */
+	};
+
+	partition@140000 {
+		label = "s_env";
+		reg = <0x240000 0x40000>;    /* 256KB */
+	};
+
+	partition@900000 {
+		label = "devinfo";
+		reg = <0x900000 0x100000>;   /* 1MB */
+		read-only;
+	};
+
+	/* kernel1 overlaps with rootfs1 by design */
+	partition@a00000 {
+		label = "kernel1";
+		reg = <0xa00000 0x2800000>;  /* 40MB */
+	};
+
+	partition@1000000 {
+		label = "rootfs1";
+		reg = <0x1000000 0x2200000>;  /* 34MB */
+	};
+
+	/* kernel2 overlaps with rootfs2 by design */
+	partition@3200000 {
+		label = "kernel2";
+		reg = <0x3200000 0x2800000>; /* 40MB */
+	};
+
+	partition@3800000 {
+		label = "rootfs2";
+		reg = <0x3800000 0x2200000>; /* 34MB */
+	};
+
+	/*
+	 * 38MB, last MB is for the BBT, not writable
+	 */
+	partition@5a00000 {
+		label = "syscfg";
+		reg = <0x5a00000 0x2600000>;
+	};
+
+	/*
+	 * Unused area between "s_env" and "devinfo".
+	 * Moved here because otherwise the renumbered
+	 * partitions would break the bootloader
+	 * supplied bootargs
+	 */
+	partition@180000 {
+		label = "unused_area";
+		reg = <0x280000 0x680000>;   /* 6.5MB */
+	};
+};
+
+&mdio {
+	status = "okay";
+
+	switch@0 {
+		compatible = "marvell,mv88e6085";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0>;
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+				label = "lan4";
+			};
+
+			port@1 {
+				reg = <1>;
+				label = "lan3";
+			};
+
+			port@2 {
+				reg = <2>;
+				label = "lan2";
+			};
+
+			port@3 {
+				reg = <3>;
+				label = "lan1";
+			};
+
+			port@4 {
+				reg = <4>;
+				label = "wan";
+			};
+
+			port@5 {
+				reg = <5>;
+				label = "cpu";
+				ethernet = <&eth2>;
+
+				fixed-link {
+					speed = <1000>;
+					full-duplex;
+				};
+			};
+		};
+	};
+};
+
+&pciec {
+	status = "okay";
+};
+
+&pcie1 {
+	/* Marvell 88W8864, 5GHz-only */
+	status = "okay";
+};
+
+&pcie2 {
+	/* Marvell 88W8864, 2GHz-only */
+	status = "okay";
+};
+
 &pinctrl {
 	keys_pin: keys-pin {
 		marvell,pins = "mpp24", "mpp29";
@@ -397,3 +380,18 @@
 &spi0 {
 	status = "disabled";
 };
+
+&uart0 {
+	/* J10: VCC, NC, RX, NC, TX, GND  */
+	status = "okay";
+};
+
+&usb0 {
+	/* USB part of the eSATA/USB 2.0 port */
+	status = "okay";
+};
+
+&usb3_1 {
+	status = "okay";
+	usb-phy = <&usb3_phy>;
+};