dt-bindings: input: microchip,cap11xx: Convert txt bindings to yaml
Convert binding for the Microchip CAP11xx series HW to the YAML syntax. Signed-off-by: David Heidelberg <david@ixit.cz> Link: https://lore.kernel.org/r/20211019234816.32060-1-david@ixit.cz Signed-off-by: Rob Herring <robh@kernel.org>
This commit is contained in:
David Heidelberg
Rob Herring
parent
14d9f6b026
commit
a8bc0707e1
|
|
@ -1,78 +0,0 @@
|
|||
Device tree bindings for Microchip CAP11xx based capacitive touch sensors
|
||||
|
||||
The node for this device must be a child of a I2C controller node, as the
|
||||
device communication via I2C only.
|
||||
|
||||
Required properties:
|
||||
|
||||
compatible: Must contain one of:
|
||||
"microchip,cap1106"
|
||||
"microchip,cap1126"
|
||||
"microchip,cap1188"
|
||||
|
||||
reg: The I2C slave address of the device.
|
||||
|
||||
interrupts: Property describing the interrupt line the
|
||||
device's ALERT#/CM_IRQ# pin is connected to.
|
||||
The device only has one interrupt source.
|
||||
|
||||
Optional properties:
|
||||
|
||||
autorepeat: Enables the Linux input system's autorepeat
|
||||
feature on the input device.
|
||||
|
||||
microchip,sensor-gain: Defines the gain of the sensor circuitry. This
|
||||
effectively controls the sensitivity, as a
|
||||
smaller delta capacitance is required to
|
||||
generate the same delta count values.
|
||||
Valid values are 1, 2, 4, and 8.
|
||||
By default, a gain of 1 is set.
|
||||
|
||||
microchip,irq-active-high: By default the interrupt pin is active low
|
||||
open drain. This property allows using the active
|
||||
high push-pull output.
|
||||
|
||||
linux,keycodes: Specifies an array of numeric keycode values to
|
||||
be used for the channels. If this property is
|
||||
omitted, KEY_A, KEY_B, etc are used as
|
||||
defaults. The array must have exactly six
|
||||
entries.
|
||||
|
||||
Example:
|
||||
|
||||
i2c_controller {
|
||||
cap1106@28 {
|
||||
compatible = "microchip,cap1106";
|
||||
interrupt-parent = <&gpio1>;
|
||||
interrupts = <0 0>;
|
||||
reg = <0x28>;
|
||||
autorepeat;
|
||||
microchip,sensor-gain = <2>;
|
||||
|
||||
linux,keycodes = <103>, /* KEY_UP */
|
||||
<106>, /* KEY_RIGHT */
|
||||
<108>, /* KEY_DOWN */
|
||||
<105>, /* KEY_LEFT */
|
||||
<109>, /* KEY_PAGEDOWN */
|
||||
<104>; /* KEY_PAGEUP */
|
||||
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
|
||||
usr@0 {
|
||||
label = "cap11xx:green:usr0";
|
||||
reg = <0>;
|
||||
};
|
||||
|
||||
usr@1 {
|
||||
label = "cap11xx:green:usr1";
|
||||
reg = <1>;
|
||||
};
|
||||
|
||||
alive@2 {
|
||||
label = "cap11xx:green:alive";
|
||||
reg = <2>;
|
||||
linux,default_trigger = "heartbeat";
|
||||
};
|
||||
};
|
||||
}
|
||||
|
|
@ -0,0 +1,148 @@
|
|||
# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
|
||||
%YAML 1.2
|
||||
---
|
||||
$id: "http://devicetree.org/schemas/input/microchip,cap11xx.yaml#"
|
||||
$schema: "http://devicetree.org/meta-schemas/core.yaml#"
|
||||
|
||||
title: Device tree bindings for Microchip CAP11xx based capacitive touch sensors
|
||||
|
||||
description: |
|
||||
The Microchip CAP1xxx Family of RightTouchTM multiple-channel capacitive
|
||||
touch controllers and LED drivers. The device communication via I2C only.
|
||||
|
||||
maintainers:
|
||||
- Rob Herring <robh@kernel.org>
|
||||
|
||||
properties:
|
||||
compatible:
|
||||
enum:
|
||||
- microchip,cap1106
|
||||
- microchip,cap1126
|
||||
- microchip,cap1188
|
||||
|
||||
reg:
|
||||
maxItems: 1
|
||||
|
||||
'#address-cells':
|
||||
const: 1
|
||||
|
||||
'#size-cells':
|
||||
const: 0
|
||||
|
||||
interrupts:
|
||||
maxItems: 1
|
||||
description: |
|
||||
Property describing the interrupt line the
|
||||
device's ALERT#/CM_IRQ# pin is connected to.
|
||||
The device only has one interrupt source.
|
||||
|
||||
autorepeat:
|
||||
description: |
|
||||
Enables the Linux input system's autorepeat feature on the input device.
|
||||
|
||||
linux,keycodes:
|
||||
minItems: 6
|
||||
maxItems: 6
|
||||
description: |
|
||||
Specifies an array of numeric keycode values to
|
||||
be used for the channels. If this property is
|
||||
omitted, KEY_A, KEY_B, etc are used as defaults.
|
||||
The array must have exactly six entries.
|
||||
|
||||
microchip,sensor-gain:
|
||||
$ref: /schemas/types.yaml#/definitions/uint32
|
||||
default: 1
|
||||
enum: [1, 2, 4, 8]
|
||||
description: |
|
||||
Defines the gain of the sensor circuitry. This
|
||||
effectively controls the sensitivity, as a
|
||||
smaller delta capacitance is required to
|
||||
generate the same delta count values.
|
||||
|
||||
microchip,irq-active-high:
|
||||
type: boolean
|
||||
description: |
|
||||
By default the interrupt pin is active low
|
||||
open drain. This property allows using the active
|
||||
high push-pull output.
|
||||
|
||||
patternProperties:
|
||||
"^led@[0-7]$":
|
||||
type: object
|
||||
description: CAP11xx LEDs
|
||||
$ref: /schemas/leds/common.yaml#
|
||||
|
||||
properties:
|
||||
reg:
|
||||
enum: [0, 1, 2, 3, 4, 5, 6, 7]
|
||||
|
||||
label: true
|
||||
|
||||
linux,default-trigger: true
|
||||
|
||||
default-state: true
|
||||
|
||||
required:
|
||||
- reg
|
||||
|
||||
additionalProperties: false
|
||||
|
||||
allOf:
|
||||
- $ref: input.yaml
|
||||
- if:
|
||||
properties:
|
||||
compatible:
|
||||
contains:
|
||||
enum:
|
||||
- microchip,cap1106
|
||||
then:
|
||||
patternProperties:
|
||||
"^led@[0-7]$": false
|
||||
|
||||
required:
|
||||
- compatible
|
||||
- interrupts
|
||||
|
||||
additionalProperties: false
|
||||
|
||||
examples:
|
||||
- |
|
||||
i2c {
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
|
||||
cap1188@28 {
|
||||
compatible = "microchip,cap1188";
|
||||
interrupt-parent = <&gpio1>;
|
||||
interrupts = <0 0>;
|
||||
reg = <0x28>;
|
||||
autorepeat;
|
||||
microchip,sensor-gain = <2>;
|
||||
|
||||
linux,keycodes = <103>, /* KEY_UP */
|
||||
<106>, /* KEY_RIGHT */
|
||||
<108>, /* KEY_DOWN */
|
||||
<105>, /* KEY_LEFT */
|
||||
<109>, /* KEY_PAGEDOWN */
|
||||
<104>; /* KEY_PAGEUP */
|
||||
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
|
||||
led@0 {
|
||||
label = "cap11xx:green:usr0";
|
||||
reg = <0>;
|
||||
};
|
||||
|
||||
led@1 {
|
||||
label = "cap11xx:green:usr1";
|
||||
reg = <1>;
|
||||
};
|
||||
|
||||
led@2 {
|
||||
label = "cap11xx:green:alive";
|
||||
reg = <2>;
|
||||
linux,default-trigger = "heartbeat";
|
||||
};
|
||||
};
|
||||
};
|
||||
Loading…
Reference in New Issue