From a4240d3af6771339c3557afe261a8a89573980a9 Mon Sep 17 00:00:00 2001 From: Nishanth Menon Date: Thu, 14 Apr 2016 12:45:58 -0500 Subject: [PATCH] ARM: dts: Add support for dra72-evm rev C (SR2.0) DRA72-EVM now has an upgrade to Rev C with SR2.0 silicon. As part of this change, a few updates were factored in that were software incompatible with previous board in few areas: - We now use DP83867 ethernet phy instead of older DP838865 which fails in certain use cases. - Two Ethernet ports now instead of the single one in rev B. - polarities changed for certain pcf gpios - Due to SoC phy current requirements, VDDA supplies are split between ldo3 and ldo2 (ldo2 was previously unused). NOTE: DSS (VDDA_VIDEO) is still supplied by ldo5, HDMI is now supplied by LDO2 instead of using LDO3. NOTE: It does not make much sense to spin off a new board compatible flag since there is no real benefit for the same. Signed-off-by: Nishanth Menon Signed-off-by: Tony Lindgren --- arch/arm/boot/dts/Makefile | 3 +- arch/arm/boot/dts/dra72-evm-common.dtsi | 833 +++++++++++++++++++++++ arch/arm/boot/dts/dra72-evm-revc.dts | 73 +++ arch/arm/boot/dts/dra72-evm.dts | 838 +----------------------- 4 files changed, 921 insertions(+), 826 deletions(-) create mode 100644 arch/arm/boot/dts/dra72-evm-common.dtsi create mode 100644 arch/arm/boot/dts/dra72-evm-revc.dts diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile index a721c4cc3548..e32392228748 100644 --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile @@ -530,7 +530,8 @@ dtb-$(CONFIG_SOC_DRA7XX) += \ am57xx-sbc-am57x.dtb \ am572x-idk.dtb \ dra7-evm.dtb \ - dra72-evm.dtb + dra72-evm.dtb \ + dra72-evm-revc.dtb dtb-$(CONFIG_ARCH_ORION5X) += \ orion5x-lacie-d2-network.dtb \ orion5x-lacie-ethernet-disk-mini-v2.dtb \ diff --git a/arch/arm/boot/dts/dra72-evm-common.dtsi b/arch/arm/boot/dts/dra72-evm-common.dtsi new file mode 100644 index 000000000000..2c880501ba2e --- /dev/null +++ b/arch/arm/boot/dts/dra72-evm-common.dtsi @@ -0,0 +1,833 @@ +/* + * Copyright (C) 2014-2016 Texas Instruments Incorporated - http://www.ti.com/ + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ +/dts-v1/; + +#include "dra72x.dtsi" +#include +#include + +/ { + compatible = "ti,dra72-evm", "ti,dra722", "ti,dra72", "ti,dra7"; + + aliases { + display0 = &hdmi0; + }; + + evm_3v3: fixedregulator-evm_3v3 { + compatible = "regulator-fixed"; + regulator-name = "evm_3v3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + }; + + aic_dvdd: fixedregulator-aic_dvdd { + /* TPS77018DBVT */ + compatible = "regulator-fixed"; + regulator-name = "aic_dvdd"; + vin-supply = <&evm_3v3>; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + + evm_3v3_sd: fixedregulator-sd { + compatible = "regulator-fixed"; + regulator-name = "evm_3v3_sd"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + enable-active-high; + gpio = <&pcf_gpio_21 5 GPIO_ACTIVE_HIGH>; + }; + + extcon_usb1: extcon_usb1 { + compatible = "linux,extcon-usb-gpio"; + id-gpio = <&pcf_gpio_21 1 GPIO_ACTIVE_HIGH>; + }; + + extcon_usb2: extcon_usb2 { + compatible = "linux,extcon-usb-gpio"; + id-gpio = <&pcf_gpio_21 2 GPIO_ACTIVE_HIGH>; + }; + + hdmi0: connector { + compatible = "hdmi-connector"; + label = "hdmi"; + + type = "a"; + + port { + hdmi_connector_in: endpoint { + remote-endpoint = <&tpd12s015_out>; + }; + }; + }; + + tpd12s015: encoder { + compatible = "ti,tpd12s015"; + + pinctrl-names = "default"; + pinctrl-0 = <&tpd12s015_pins>; + + gpios = <&pcf_hdmi 4 GPIO_ACTIVE_HIGH>, /* P4, CT CP HPD */ + <&pcf_hdmi 5 GPIO_ACTIVE_HIGH>, /* P5, LS OE */ + <&gpio7 12 GPIO_ACTIVE_HIGH>; /* gpio7_12/sp1_cs2, HPD */ + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + + tpd12s015_in: endpoint { + remote-endpoint = <&hdmi_out>; + }; + }; + + port@1 { + reg = <1>; + + tpd12s015_out: endpoint { + remote-endpoint = <&hdmi_connector_in>; + }; + }; + }; + }; + + sound0: sound0 { + compatible = "simple-audio-card"; + simple-audio-card,name = "DRA7xx-EVM"; + simple-audio-card,widgets = + "Headphone", "Headphone Jack", + "Line", "Line Out", + "Microphone", "Mic Jack", + "Line", "Line In"; + simple-audio-card,routing = + "Headphone Jack", "HPLOUT", + "Headphone Jack", "HPROUT", + "Line Out", "LLOUT", + "Line Out", "RLOUT", + "MIC3L", "Mic Jack", + "MIC3R", "Mic Jack", + "Mic Jack", "Mic Bias", + "LINE1L", "Line In", + "LINE1R", "Line In"; + simple-audio-card,format = "dsp_b"; + simple-audio-card,bitclock-master = <&sound0_master>; + simple-audio-card,frame-master = <&sound0_master>; + simple-audio-card,bitclock-inversion; + + sound0_master: simple-audio-card,cpu { + sound-dai = <&mcasp3>; + system-clock-frequency = <5644800>; + }; + + simple-audio-card,codec { + sound-dai = <&tlv320aic3106>; + clocks = <&atl_clkin2_ck>; + }; + }; +}; + +&dra7_pmx_core { + i2c1_pins: pinmux_i2c1_pins { + pinctrl-single,pins = < + DRA7XX_CORE_IOPAD(0x3800, PIN_INPUT | MUX_MODE0) /* i2c1_sda.i2c1_sda */ + DRA7XX_CORE_IOPAD(0x3804, PIN_INPUT | MUX_MODE0) /* i2c1_scl.i2c1_scl */ + >; + }; + + i2c5_pins: pinmux_i2c5_pins { + pinctrl-single,pins = < + DRA7XX_CORE_IOPAD(0x36b4, PIN_INPUT | MUX_MODE10) /* mcasp1_axr0.i2c5_sda */ + DRA7XX_CORE_IOPAD(0x36b8, PIN_INPUT | MUX_MODE10) /* mcasp1_axr1.i2c5_scl */ + >; + }; + + i2c5_pins: pinmux_i2c5_pins { + pinctrl-single,pins = < + DRA7XX_CORE_IOPAD(0x36b4, PIN_INPUT | MUX_MODE10) /* mcasp1_axr0.i2c5_sda */ + DRA7XX_CORE_IOPAD(0x36b8, PIN_INPUT | MUX_MODE10) /* mcasp1_axr1.i2c5_scl */ + >; + }; + + nand_default: nand_default { + pinctrl-single,pins = < + DRA7XX_CORE_IOPAD(0x3400, PIN_INPUT | MUX_MODE0) /* gpmc_ad0 */ + DRA7XX_CORE_IOPAD(0x3404, PIN_INPUT | MUX_MODE0) /* gpmc_ad1 */ + DRA7XX_CORE_IOPAD(0x3408, PIN_INPUT | MUX_MODE0) /* gpmc_ad2 */ + DRA7XX_CORE_IOPAD(0x340c, PIN_INPUT | MUX_MODE0) /* gpmc_ad3 */ + DRA7XX_CORE_IOPAD(0x3410, PIN_INPUT | MUX_MODE0) /* gpmc_ad4 */ + DRA7XX_CORE_IOPAD(0x3414, PIN_INPUT | MUX_MODE0) /* gpmc_ad5 */ + DRA7XX_CORE_IOPAD(0x3418, PIN_INPUT | MUX_MODE0) /* gpmc_ad6 */ + DRA7XX_CORE_IOPAD(0x341c, PIN_INPUT | MUX_MODE0) /* gpmc_ad7 */ + DRA7XX_CORE_IOPAD(0x3420, PIN_INPUT | MUX_MODE0) /* gpmc_ad8 */ + DRA7XX_CORE_IOPAD(0x3424, PIN_INPUT | MUX_MODE0) /* gpmc_ad9 */ + DRA7XX_CORE_IOPAD(0x3428, PIN_INPUT | MUX_MODE0) /* gpmc_ad10 */ + DRA7XX_CORE_IOPAD(0x342c, PIN_INPUT | MUX_MODE0) /* gpmc_ad11 */ + DRA7XX_CORE_IOPAD(0x3430, PIN_INPUT | MUX_MODE0) /* gpmc_ad12 */ + DRA7XX_CORE_IOPAD(0x3434, PIN_INPUT | MUX_MODE0) /* gpmc_ad13 */ + DRA7XX_CORE_IOPAD(0x3438, PIN_INPUT | MUX_MODE0) /* gpmc_ad14 */ + DRA7XX_CORE_IOPAD(0x343c, PIN_INPUT | MUX_MODE0) /* gpmc_ad15 */ + DRA7XX_CORE_IOPAD(0x34b4, PIN_OUTPUT | MUX_MODE0) /* gpmc_cs0 */ + DRA7XX_CORE_IOPAD(0x34c4, PIN_OUTPUT | MUX_MODE0) /* gpmc_advn_ale */ + DRA7XX_CORE_IOPAD(0x34cc, PIN_OUTPUT | MUX_MODE0) /* gpmc_wen */ + DRA7XX_CORE_IOPAD(0x34c8, PIN_OUTPUT | MUX_MODE0) /* gpmc_oen_ren */ + DRA7XX_CORE_IOPAD(0x34d0, PIN_OUTPUT | MUX_MODE0) /* gpmc_ben0 */ + DRA7XX_CORE_IOPAD(0x34d8, PIN_INPUT | MUX_MODE0) /* gpmc_wait0 */ + >; + }; + + usb1_pins: pinmux_usb1_pins { + pinctrl-single,pins = < + DRA7XX_CORE_IOPAD(0x3680, PIN_INPUT_SLEW | MUX_MODE0) /* usb1_drvvbus */ + >; + }; + + usb2_pins: pinmux_usb2_pins { + pinctrl-single,pins = < + DRA7XX_CORE_IOPAD(0x3684, PIN_INPUT_SLEW | MUX_MODE0) /* usb2_drvvbus */ + >; + }; + + tps65917_pins_default: tps65917_pins_default { + pinctrl-single,pins = < + DRA7XX_CORE_IOPAD(0x3824, PIN_INPUT_PULLUP | MUX_MODE1) /* wakeup3.sys_nirq1 */ + >; + }; + + mmc1_pins_default: mmc1_pins_default { + pinctrl-single,pins = < + DRA7XX_CORE_IOPAD(0x376c, PIN_INPUT | MUX_MODE14) /* mmc1sdcd.gpio219 */ + DRA7XX_CORE_IOPAD(0x3754, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_clk.clk */ + DRA7XX_CORE_IOPAD(0x3758, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_cmd.cmd */ + DRA7XX_CORE_IOPAD(0x375c, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_dat0.dat0 */ + DRA7XX_CORE_IOPAD(0x3760, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_dat1.dat1 */ + DRA7XX_CORE_IOPAD(0x3764, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_dat2.dat2 */ + DRA7XX_CORE_IOPAD(0x3768, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_dat3.dat3 */ + >; + }; + + mmc2_pins_default: mmc2_pins_default { + pinctrl-single,pins = < + DRA7XX_CORE_IOPAD(0x349c, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a23.mmc2_clk */ + DRA7XX_CORE_IOPAD(0x34b0, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_cs1.mmc2_cmd */ + DRA7XX_CORE_IOPAD(0x34a0, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a24.mmc2_dat0 */ + DRA7XX_CORE_IOPAD(0x34a4, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a25.mmc2_dat1 */ + DRA7XX_CORE_IOPAD(0x34a8, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a26.mmc2_dat2 */ + DRA7XX_CORE_IOPAD(0x34ac, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a27.mmc2_dat3 */ + DRA7XX_CORE_IOPAD(0x348c, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a19.mmc2_dat4 */ + DRA7XX_CORE_IOPAD(0x3490, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a20.mmc2_dat5 */ + DRA7XX_CORE_IOPAD(0x3494, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a21.mmc2_dat6 */ + DRA7XX_CORE_IOPAD(0x3498, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a22.mmc2_dat7 */ + >; + }; + + dcan1_pins_default: dcan1_pins_default { + pinctrl-single,pins = < + DRA7XX_CORE_IOPAD(0x37d0, PIN_OUTPUT_PULLUP | MUX_MODE0) /* dcan1_tx */ + DRA7XX_CORE_IOPAD(0x3818, PULL_UP | MUX_MODE1) /* wakeup0.dcan1_rx */ + >; + }; + + dcan1_pins_sleep: dcan1_pins_sleep { + pinctrl-single,pins = < + DRA7XX_CORE_IOPAD(0x37d0, MUX_MODE15 | PULL_UP) /* dcan1_tx.off */ + DRA7XX_CORE_IOPAD(0x3818, MUX_MODE15 | PULL_UP) /* wakeup0.off */ + >; + }; + + qspi1_pins: pinmux_qspi1_pins { + pinctrl-single,pins = < + DRA7XX_CORE_IOPAD(0x3474, PIN_OUTPUT | MUX_MODE1) /* gpmc_a13.qspi1_rtclk */ + DRA7XX_CORE_IOPAD(0x3478, PIN_INPUT | MUX_MODE1) /* gpmc_a14.qspi1_d3 */ + DRA7XX_CORE_IOPAD(0x347c, PIN_INPUT | MUX_MODE1) /* gpmc_a15.qspi1_d2 */ + DRA7XX_CORE_IOPAD(0x3480, PIN_INPUT | MUX_MODE1) /* gpmc_a16.qspi1_d1 */ + DRA7XX_CORE_IOPAD(0x3484, PIN_INPUT | MUX_MODE1) /* gpmc_a17.qspi1_d0 */ + DRA7XX_CORE_IOPAD(0x3488, PIN_OUTPUT | MUX_MODE1) /* qpmc_a18.qspi1_sclk */ + DRA7XX_CORE_IOPAD(0x34b8, PIN_OUTPUT | MUX_MODE1) /* gpmc_cs2.qspi1_cs0 */ + >; + }; + + hdmi_pins: pinmux_hdmi_pins { + pinctrl-single,pins = < + DRA7XX_CORE_IOPAD(0x3808, PIN_INPUT | MUX_MODE1) /* i2c2_sda.hdmi1_ddc_scl */ + DRA7XX_CORE_IOPAD(0x380c, PIN_INPUT | MUX_MODE1) /* i2c2_scl.hdmi1_ddc_sda */ + >; + }; + + tpd12s015_pins: pinmux_tpd12s015_pins { + pinctrl-single,pins = < + DRA7XX_CORE_IOPAD(0x37b8, PIN_INPUT_PULLDOWN | MUX_MODE14) /* gpio7_12 HPD */ + >; + }; + + atl_pins: pinmux_atl_pins { + pinctrl-single,pins = < + DRA7XX_CORE_IOPAD(0x3698, PIN_OUTPUT | MUX_MODE5) /* xref_clk1.atl_clk1 */ + DRA7XX_CORE_IOPAD(0x369c, PIN_OUTPUT | MUX_MODE5) /* xref_clk2.atl_clk2 */ + >; + }; + + mcasp3_pins: pinmux_mcasp3_pins { + pinctrl-single,pins = < + DRA7XX_CORE_IOPAD(0x3724, PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* mcasp3_aclkx */ + DRA7XX_CORE_IOPAD(0x3728, PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* mcasp3_fsx */ + DRA7XX_CORE_IOPAD(0x372c, PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* mcasp3_axr0 */ + DRA7XX_CORE_IOPAD(0x3730, PIN_INPUT_PULLDOWN | MUX_MODE0) /* mcasp3_axr1 */ + >; + }; + + mcasp3_sleep_pins: pinmux_mcasp3_sleep_pins { + pinctrl-single,pins = < + DRA7XX_CORE_IOPAD(0x3724, PIN_INPUT_PULLDOWN | MUX_MODE15) + DRA7XX_CORE_IOPAD(0x3728, PIN_INPUT_PULLDOWN | MUX_MODE15) + DRA7XX_CORE_IOPAD(0x372c, PIN_INPUT_PULLDOWN | MUX_MODE15) + DRA7XX_CORE_IOPAD(0x3730, PIN_INPUT_PULLDOWN | MUX_MODE15) + >; + }; +}; + +&i2c1 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&i2c1_pins>; + clock-frequency = <400000>; + + tps65917: tps65917@58 { + compatible = "ti,tps65917"; + reg = <0x58>; + + pinctrl-names = "default"; + pinctrl-0 = <&tps65917_pins_default>; + + interrupts = ; /* IRQ_SYS_1N */ + interrupt-controller; + #interrupt-cells = <2>; + + ti,system-power-controller; + + tps65917_pmic { + compatible = "ti,tps65917-pmic"; + + tps65917_regulators: regulators { + smps1_reg: smps1 { + /* VDD_MPU */ + regulator-name = "smps1"; + regulator-min-microvolt = <850000>; + regulator-max-microvolt = <1250000>; + regulator-always-on; + regulator-boot-on; + }; + + smps2_reg: smps2 { + /* VDD_CORE */ + regulator-name = "smps2"; + regulator-min-microvolt = <850000>; + regulator-max-microvolt = <1060000>; + regulator-boot-on; + regulator-always-on; + }; + + smps3_reg: smps3 { + /* VDD_GPU IVA DSPEVE */ + regulator-name = "smps3"; + regulator-min-microvolt = <850000>; + regulator-max-microvolt = <1250000>; + regulator-boot-on; + regulator-always-on; + }; + + smps4_reg: smps4 { + /* VDDS1V8 */ + regulator-name = "smps4"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + regulator-boot-on; + }; + + smps5_reg: smps5 { + /* VDD_DDR */ + regulator-name = "smps5"; + regulator-min-microvolt = <1350000>; + regulator-max-microvolt = <1350000>; + regulator-boot-on; + regulator-always-on; + }; + + ldo1_reg: ldo1 { + /* LDO1_OUT --> SDIO */ + regulator-name = "ldo1"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + regulator-boot-on; + regulator-allow-bypass; + }; + + ldo3_reg: ldo3 { + /* VDDA_1V8_PHY */ + regulator-name = "ldo3"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-boot-on; + regulator-always-on; + }; + + ldo5_reg: ldo5 { + /* VDDA_1V8_PLL */ + regulator-name = "ldo5"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + regulator-boot-on; + }; + + ldo4_reg: ldo4 { + /* VDDA_3V_USB: VDDA_USBHS33 */ + regulator-name = "ldo4"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + }; + }; + }; + + tps65917_power_button { + compatible = "ti,palmas-pwrbutton"; + interrupt-parent = <&tps65917>; + interrupts = <1 IRQ_TYPE_NONE>; + wakeup-source; + ti,palmas-long-press-seconds = <6>; + }; + }; + + pcf_gpio_21: gpio@21 { + compatible = "nxp,pcf8575"; + reg = <0x21>; + lines-initial-states = <0x1408>; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + }; + + tlv320aic3106: tlv320aic3106@19 { + #sound-dai-cells = <0>; + compatible = "ti,tlv320aic3106"; + reg = <0x19>; + adc-settle-ms = <40>; + ai3x-micbias-vg = <1>; /* 2.0V */ + status = "okay"; + + /* Regulators */ + AVDD-supply = <&evm_3v3>; + IOVDD-supply = <&evm_3v3>; + DRVDD-supply = <&evm_3v3>; + DVDD-supply = <&aic_dvdd>; + }; +}; + +&i2c5 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&i2c5_pins>; + clock-frequency = <400000>; + + pcf_hdmi: pcf8575@26 { + compatible = "nxp,pcf8575"; + reg = <0x26>; + gpio-controller; + #gpio-cells = <2>; + /* + * initial state is used here to keep the mdio interface + * selected on RU89 through SEL_VIN4_MUX_S0, VIN2_S1 and + * VIN2_S0 driven high otherwise Ethernet stops working + * VIN6_SEL_S0 is low, thus selecting McASP3 over VIN6 + */ + lines-initial-states = <0x0f2b>; + + p1 { + /* vin6_sel_s0: high: VIN6, low: audio */ + gpio-hog; + gpios = <1 GPIO_ACTIVE_HIGH>; + output-low; + line-name = "vin6_sel_s0"; + }; + }; +}; + +&uart1 { + status = "okay"; + interrupts-extended = <&crossbar_mpu GIC_SPI 67 IRQ_TYPE_LEVEL_HIGH>, + <&dra7_pmx_core 0x3e0>; +}; + +&elm { + status = "okay"; +}; + +&gpmc { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&nand_default>; + ranges = <0 0 0x08000000 0x01000000>; /* minimum GPMC partition = 16MB */ + nand@0,0 { + /* To use NAND, DIP switch SW5 must be set like so: + * SW5.1 (NAND_SELn) = ON (LOW) + * SW5.9 (GPMC_WPN) = OFF (HIGH) + */ + compatible = "ti,omap2-nand"; + reg = <0 0 4>; /* device IO registers */ + interrupt-parent = <&gpmc>; + interrupts = <0 IRQ_TYPE_NONE>, /* fifoevent */ + <1 IRQ_TYPE_NONE>; /* termcount */ + rb-gpios = <&gpmc 0 GPIO_ACTIVE_HIGH>; /* gpmc_wait0 pin */ + ti,nand-ecc-opt = "bch8"; + ti,elm-id = <&elm>; + nand-bus-width = <16>; + gpmc,device-width = <2>; + gpmc,sync-clk-ps = <0>; + gpmc,cs-on-ns = <0>; + gpmc,cs-rd-off-ns = <80>; + gpmc,cs-wr-off-ns = <80>; + gpmc,adv-on-ns = <0>; + gpmc,adv-rd-off-ns = <60>; + gpmc,adv-wr-off-ns = <60>; + gpmc,we-on-ns = <10>; + gpmc,we-off-ns = <50>; + gpmc,oe-on-ns = <4>; + gpmc,oe-off-ns = <40>; + gpmc,access-ns = <40>; + gpmc,wr-access-ns = <80>; + gpmc,rd-cycle-ns = <80>; + gpmc,wr-cycle-ns = <80>; + gpmc,bus-turnaround-ns = <0>; + gpmc,cycle2cycle-delay-ns = <0>; + gpmc,clk-activation-ns = <0>; + gpmc,wr-data-mux-bus-ns = <0>; + /* MTD partition table */ + /* All SPL-* partitions are sized to minimal length + * which can be independently programmable. For + * NAND flash this is equal to size of erase-block */ + #address-cells = <1>; + #size-cells = <1>; + partition@0 { + label = "NAND.SPL"; + reg = <0x00000000 0x000020000>; + }; + partition@1 { + label = "NAND.SPL.backup1"; + reg = <0x00020000 0x00020000>; + }; + partition@2 { + label = "NAND.SPL.backup2"; + reg = <0x00040000 0x00020000>; + }; + partition@3 { + label = "NAND.SPL.backup3"; + reg = <0x00060000 0x00020000>; + }; + partition@4 { + label = "NAND.u-boot-spl-os"; + reg = <0x00080000 0x00040000>; + }; + partition@5 { + label = "NAND.u-boot"; + reg = <0x000c0000 0x00100000>; + }; + partition@6 { + label = "NAND.u-boot-env"; + reg = <0x001c0000 0x00020000>; + }; + partition@7 { + label = "NAND.u-boot-env.backup1"; + reg = <0x001e0000 0x00020000>; + }; + partition@8 { + label = "NAND.kernel"; + reg = <0x00200000 0x00800000>; + }; + partition@9 { + label = "NAND.file-system"; + reg = <0x00a00000 0x0f600000>; + }; + }; +}; + +&usb2_phy1 { + phy-supply = <&ldo4_reg>; +}; + +&usb2_phy2 { + phy-supply = <&ldo4_reg>; +}; + +&omap_dwc3_1 { + extcon = <&extcon_usb1>; +}; + +&omap_dwc3_2 { + extcon = <&extcon_usb2>; +}; + +&usb1 { + dr_mode = "peripheral"; + pinctrl-names = "default"; + pinctrl-0 = <&usb1_pins>; +}; + +&usb2 { + dr_mode = "host"; + pinctrl-names = "default"; + pinctrl-0 = <&usb2_pins>; +}; + +&mmc1 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&mmc1_pins_default>; + vmmc-supply = <&evm_3v3_sd>; + vmmc_aux-supply = <&ldo1_reg>; + bus-width = <4>; + /* + * SDCD signal is not being used here - using the fact that GPIO mode + * is a viable alternative + */ + cd-gpios = <&gpio6 27 GPIO_ACTIVE_LOW>; + max-frequency = <192000000>; +}; + +&mmc2 { + /* SW5-3 in ON position */ + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&mmc2_pins_default>; + + vmmc-supply = <&evm_3v3>; + bus-width = <8>; + ti,non-removable; + max-frequency = <192000000>; +}; + +&dra7_pmx_core { + cpsw_default: cpsw_default { + pinctrl-single,pins = < + /* Slave 2 */ + DRA7XX_CORE_IOPAD(0x3598, PIN_OUTPUT | MUX_MODE3) /* vin2a_d12.rgmii1_txc */ + DRA7XX_CORE_IOPAD(0x359c, PIN_OUTPUT | MUX_MODE3) /* vin2a_d13.rgmii1_tctl */ + DRA7XX_CORE_IOPAD(0x35a0, PIN_OUTPUT | MUX_MODE3) /* vin2a_d14.rgmii1_td3 */ + DRA7XX_CORE_IOPAD(0x35a4, PIN_OUTPUT | MUX_MODE3) /* vin2a_d15.rgmii1_td2 */ + DRA7XX_CORE_IOPAD(0x35a8, PIN_OUTPUT | MUX_MODE3) /* vin2a_d16.rgmii1_td1 */ + DRA7XX_CORE_IOPAD(0x35ac, PIN_OUTPUT | MUX_MODE3) /* vin2a_d17.rgmii1_td0 */ + DRA7XX_CORE_IOPAD(0x35b0, PIN_INPUT | MUX_MODE3) /* vin2a_d18.rgmii1_rclk */ + DRA7XX_CORE_IOPAD(0x35b4, PIN_INPUT | MUX_MODE3) /* vin2a_d19.rgmii1_rctl */ + DRA7XX_CORE_IOPAD(0x35b8, PIN_INPUT | MUX_MODE3) /* vin2a_d20.rgmii1_rd3 */ + DRA7XX_CORE_IOPAD(0x35bc, PIN_INPUT | MUX_MODE3) /* vin2a_d21.rgmii1_rd2 */ + DRA7XX_CORE_IOPAD(0x35c0, PIN_INPUT | MUX_MODE3) /* vin2a_d22.rgmii1_rd1 */ + DRA7XX_CORE_IOPAD(0x35c4, PIN_INPUT | MUX_MODE3) /* vin2a_d23.rgmii1_rd0 */ + >; + + }; + + cpsw_sleep: cpsw_sleep { + pinctrl-single,pins = < + /* Slave 2 */ + DRA7XX_CORE_IOPAD(0x3598, MUX_MODE15) + DRA7XX_CORE_IOPAD(0x359c, MUX_MODE15) + DRA7XX_CORE_IOPAD(0x35a0, MUX_MODE15) + DRA7XX_CORE_IOPAD(0x35a4, MUX_MODE15) + DRA7XX_CORE_IOPAD(0x35a8, MUX_MODE15) + DRA7XX_CORE_IOPAD(0x35ac, MUX_MODE15) + DRA7XX_CORE_IOPAD(0x35b0, MUX_MODE15) + DRA7XX_CORE_IOPAD(0x35b4, MUX_MODE15) + DRA7XX_CORE_IOPAD(0x35b8, MUX_MODE15) + DRA7XX_CORE_IOPAD(0x35bc, MUX_MODE15) + DRA7XX_CORE_IOPAD(0x35c0, MUX_MODE15) + DRA7XX_CORE_IOPAD(0x35c4, MUX_MODE15) + >; + }; + + davinci_mdio_default: davinci_mdio_default { + pinctrl-single,pins = < + /* MDIO */ + DRA7XX_CORE_IOPAD(0x363c, PIN_OUTPUT_PULLUP | MUX_MODE0) /* mdio_d.mdio_d */ + DRA7XX_CORE_IOPAD(0x3640, PIN_INPUT_PULLUP | MUX_MODE0) /* mdio_clk.mdio_clk */ + >; + }; + + davinci_mdio_sleep: davinci_mdio_sleep { + pinctrl-single,pins = < + DRA7XX_CORE_IOPAD(0x363c, MUX_MODE15) + DRA7XX_CORE_IOPAD(0x3640, MUX_MODE15) + >; + }; +}; + +&mac { + status = "okay"; + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&cpsw_default>; + pinctrl-1 = <&cpsw_sleep>; +}; + +&davinci_mdio { + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&davinci_mdio_default>; + pinctrl-1 = <&davinci_mdio_sleep>; +}; + +&dcan1 { + status = "ok"; + pinctrl-names = "default", "sleep", "active"; + pinctrl-0 = <&dcan1_pins_sleep>; + pinctrl-1 = <&dcan1_pins_sleep>; + pinctrl-2 = <&dcan1_pins_default>; +}; + +&qspi { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&qspi1_pins>; + + spi-max-frequency = <48000000>; + m25p80@0 { + compatible = "s25fl256s1"; + spi-max-frequency = <48000000>; + reg = <0>; + spi-tx-bus-width = <1>; + spi-rx-bus-width = <4>; + spi-cpol; + spi-cpha; + #address-cells = <1>; + #size-cells = <1>; + + /* MTD partition table. + * The ROM checks the first four physical blocks + * for a valid file to boot and the flash here is + * 64KiB block size. + */ + partition@0 { + label = "QSPI.SPL"; + reg = <0x00000000 0x000010000>; + }; + partition@1 { + label = "QSPI.SPL.backup1"; + reg = <0x00010000 0x00010000>; + }; + partition@2 { + label = "QSPI.SPL.backup2"; + reg = <0x00020000 0x00010000>; + }; + partition@3 { + label = "QSPI.SPL.backup3"; + reg = <0x00030000 0x00010000>; + }; + partition@4 { + label = "QSPI.u-boot"; + reg = <0x00040000 0x00100000>; + }; + partition@5 { + label = "QSPI.u-boot-spl-os"; + reg = <0x00140000 0x00080000>; + }; + partition@6 { + label = "QSPI.u-boot-env"; + reg = <0x001c0000 0x00010000>; + }; + partition@7 { + label = "QSPI.u-boot-env.backup1"; + reg = <0x001d0000 0x0010000>; + }; + partition@8 { + label = "QSPI.kernel"; + reg = <0x001e0000 0x0800000>; + }; + partition@9 { + label = "QSPI.file-system"; + reg = <0x009e0000 0x01620000>; + }; + }; +}; + +&dss { + status = "ok"; + + vdda_video-supply = <&ldo5_reg>; +}; + +&hdmi { + status = "ok"; + + pinctrl-names = "default"; + pinctrl-0 = <&hdmi_pins>; + + port { + hdmi_out: endpoint { + remote-endpoint = <&tpd12s015_in>; + }; + }; +}; + +&atl { + pinctrl-names = "default"; + pinctrl-0 = <&atl_pins>; + + assigned-clocks = <&abe_dpll_sys_clk_mux>, + <&atl_gfclk_mux>, + <&dpll_abe_ck>, + <&dpll_abe_m2x2_ck>, + <&atl_clkin2_ck>; + assigned-clock-parents = <&sys_clkin2>, <&dpll_abe_m2_ck>; + assigned-clock-rates = <0>, <0>, <180633600>, <361267200>, <5644800>; + + status = "okay"; + + atl2 { + bws = ; + aws = ; + }; +}; + +&mcasp3 { + #sound-dai-cells = <0>; + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&mcasp3_pins>; + pinctrl-1 = <&mcasp3_sleep_pins>; + + assigned-clocks = <&mcasp3_ahclkx_mux>; + assigned-clock-parents = <&atl_clkin2_ck>; + + status = "okay"; + + op-mode = <0>; /* MCASP_IIS_MODE */ + tdm-slots = <2>; + /* 4 serializer */ + serial-dir = < /* 0: INACTIVE, 1: TX, 2: RX */ + 1 2 0 0 + >; + tx-num-evt = <32>; + rx-num-evt = <32>; +}; + +&mailbox5 { + status = "okay"; + mbox_ipu1_ipc3x: mbox_ipu1_ipc3x { + status = "okay"; + }; + mbox_dsp1_ipc3x: mbox_dsp1_ipc3x { + status = "okay"; + }; +}; + +&mailbox6 { + status = "okay"; + mbox_ipu2_ipc3x: mbox_ipu2_ipc3x { + status = "okay"; + }; +}; diff --git a/arch/arm/boot/dts/dra72-evm-revc.dts b/arch/arm/boot/dts/dra72-evm-revc.dts new file mode 100644 index 000000000000..f9cfd3bb4dc2 --- /dev/null +++ b/arch/arm/boot/dts/dra72-evm-revc.dts @@ -0,0 +1,73 @@ +/* + * Copyright (C) 2016 Texas Instruments Incorporated - http://www.ti.com/ + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ +#include "dra72-evm-common.dtsi" +#include + +/ { + model = "TI DRA722 Rev C EVM"; + + memory { + device_type = "memory"; + reg = <0x0 0x80000000 0x0 0x80000000>; /* 2GB */ + }; +}; + +&tps65917_regulators { + ldo2_reg: ldo2 { + /* LDO2_OUT --> VDDA_1V8_PHY2 */ + regulator-name = "ldo2"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + regulator-boot-on; + }; +}; + +&hdmi { + vdda-supply = <&ldo2_reg>; +}; + +&pcf_gpio_21 { + interrupt-parent = <&gpio3>; + interrupts = <30 IRQ_TYPE_EDGE_FALLING>; +}; + +&mac { + mode-gpios = <&pcf_gpio_21 4 GPIO_ACTIVE_LOW>, + <&pcf_hdmi 9 GPIO_ACTIVE_LOW>, /* P11 */ + <&pcf_hdmi 10 GPIO_ACTIVE_LOW>; /* P12 */ + dual_emac; +}; + +&cpsw_emac0 { + phy_id = <&davinci_mdio>, <2>; + phy-mode = "rgmii-id"; + dual_emac_res_vlan = <1>; +}; + +&cpsw_emac1 { + phy_id = <&davinci_mdio>, <3>; + phy-mode = "rgmii-id"; + dual_emac_res_vlan = <2>; +}; + +&davinci_mdio { + dp83867_0: ethernet-phy@2 { + reg = <2>; + ti,rx-internal-delay = ; + ti,tx-internal-delay = ; + ti,fifo-depth = ; + }; + + dp83867_1: ethernet-phy@3 { + reg = <3>; + ti,rx-internal-delay = ; + ti,tx-internal-delay = ; + ti,fifo-depth = ; + }; +}; diff --git a/arch/arm/boot/dts/dra72-evm.dts b/arch/arm/boot/dts/dra72-evm.dts index 3e63f660cd7c..cc1d32ca4a8a 100644 --- a/arch/arm/boot/dts/dra72-evm.dts +++ b/arch/arm/boot/dts/dra72-evm.dts @@ -1,695 +1,40 @@ /* - * Copyright (C) 2014 Texas Instruments Incorporated - http://www.ti.com/ + * Copyright (C) 2014-2016 Texas Instruments Incorporated - http://www.ti.com/ * * This program is free software; you can redistribute it and/or modify * it under the terms of the GNU General Public License version 2 as * published by the Free Software Foundation. */ -/dts-v1/; - -#include "dra72x.dtsi" -#include -#include - +#include "dra72-evm-common.dtsi" / { model = "TI DRA722"; - compatible = "ti,dra72-evm", "ti,dra722", "ti,dra72", "ti,dra7"; memory { device_type = "memory"; reg = <0x0 0x80000000 0x0 0x40000000>; /* 1024 MB */ }; +}; - aliases { - display0 = &hdmi0; - }; - - evm_3v3: fixedregulator-evm_3v3 { - compatible = "regulator-fixed"; - regulator-name = "evm_3v3"; - regulator-min-microvolt = <3300000>; - regulator-max-microvolt = <3300000>; - }; - - aic_dvdd: fixedregulator-aic_dvdd { - /* TPS77018DBVT */ - compatible = "regulator-fixed"; - regulator-name = "aic_dvdd"; - vin-supply = <&evm_3v3>; +&tps65917_regulators { + ldo2_reg: ldo2 { + /* LDO2_OUT --> TP1017 (UNUSED) */ + regulator-name = "ldo2"; regulator-min-microvolt = <1800000>; - regulator-max-microvolt = <1800000>; - }; - - evm_3v3_sd: fixedregulator-sd { - compatible = "regulator-fixed"; - regulator-name = "evm_3v3_sd"; - regulator-min-microvolt = <3300000>; regulator-max-microvolt = <3300000>; - enable-active-high; - gpio = <&pcf_gpio_21 5 GPIO_ACTIVE_HIGH>; - }; - - extcon_usb1: extcon_usb1 { - compatible = "linux,extcon-usb-gpio"; - id-gpio = <&pcf_gpio_21 1 GPIO_ACTIVE_HIGH>; - }; - - extcon_usb2: extcon_usb2 { - compatible = "linux,extcon-usb-gpio"; - id-gpio = <&pcf_gpio_21 2 GPIO_ACTIVE_HIGH>; - }; - - hdmi0: connector { - compatible = "hdmi-connector"; - label = "hdmi"; - - type = "a"; - - port { - hdmi_connector_in: endpoint { - remote-endpoint = <&tpd12s015_out>; - }; - }; - }; - - tpd12s015: encoder { - compatible = "ti,tpd12s015"; - - pinctrl-names = "default"; - pinctrl-0 = <&tpd12s015_pins>; - - gpios = <&pcf_hdmi 4 GPIO_ACTIVE_HIGH>, /* P4, CT CP HPD */ - <&pcf_hdmi 5 GPIO_ACTIVE_HIGH>, /* P5, LS OE */ - <&gpio7 12 GPIO_ACTIVE_HIGH>; /* gpio7_12/sp1_cs2, HPD */ - - ports { - #address-cells = <1>; - #size-cells = <0>; - - port@0 { - reg = <0>; - - tpd12s015_in: endpoint { - remote-endpoint = <&hdmi_out>; - }; - }; - - port@1 { - reg = <1>; - - tpd12s015_out: endpoint { - remote-endpoint = <&hdmi_connector_in>; - }; - }; - }; - }; - - sound0: sound0 { - compatible = "simple-audio-card"; - simple-audio-card,name = "DRA7xx-EVM"; - simple-audio-card,widgets = - "Headphone", "Headphone Jack", - "Line", "Line Out", - "Microphone", "Mic Jack", - "Line", "Line In"; - simple-audio-card,routing = - "Headphone Jack", "HPLOUT", - "Headphone Jack", "HPROUT", - "Line Out", "LLOUT", - "Line Out", "RLOUT", - "MIC3L", "Mic Jack", - "MIC3R", "Mic Jack", - "Mic Jack", "Mic Bias", - "LINE1L", "Line In", - "LINE1R", "Line In"; - simple-audio-card,format = "dsp_b"; - simple-audio-card,bitclock-master = <&sound0_master>; - simple-audio-card,frame-master = <&sound0_master>; - simple-audio-card,bitclock-inversion; - - sound0_master: simple-audio-card,cpu { - sound-dai = <&mcasp3>; - system-clock-frequency = <5644800>; - }; - - simple-audio-card,codec { - sound-dai = <&tlv320aic3106>; - clocks = <&atl_clkin2_ck>; - }; + regulator-allow-bypass; }; }; -&dra7_pmx_core { - i2c1_pins: pinmux_i2c1_pins { - pinctrl-single,pins = < - DRA7XX_CORE_IOPAD(0x3800, PIN_INPUT | MUX_MODE0) /* i2c1_sda.i2c1_sda */ - DRA7XX_CORE_IOPAD(0x3804, PIN_INPUT | MUX_MODE0) /* i2c1_scl.i2c1_scl */ - >; - }; - - i2c5_pins: pinmux_i2c5_pins { - pinctrl-single,pins = < - DRA7XX_CORE_IOPAD(0x36b4, PIN_INPUT | MUX_MODE10) /* mcasp1_axr0.i2c5_sda */ - DRA7XX_CORE_IOPAD(0x36b8, PIN_INPUT | MUX_MODE10) /* mcasp1_axr1.i2c5_scl */ - >; - }; - - i2c5_pins: pinmux_i2c5_pins { - pinctrl-single,pins = < - DRA7XX_CORE_IOPAD(0x36b4, PIN_INPUT | MUX_MODE10) /* mcasp1_axr0.i2c5_sda */ - DRA7XX_CORE_IOPAD(0x36b8, PIN_INPUT | MUX_MODE10) /* mcasp1_axr1.i2c5_scl */ - >; - }; - - nand_default: nand_default { - pinctrl-single,pins = < - DRA7XX_CORE_IOPAD(0x3400, PIN_INPUT | MUX_MODE0) /* gpmc_ad0 */ - DRA7XX_CORE_IOPAD(0x3404, PIN_INPUT | MUX_MODE0) /* gpmc_ad1 */ - DRA7XX_CORE_IOPAD(0x3408, PIN_INPUT | MUX_MODE0) /* gpmc_ad2 */ - DRA7XX_CORE_IOPAD(0x340c, PIN_INPUT | MUX_MODE0) /* gpmc_ad3 */ - DRA7XX_CORE_IOPAD(0x3410, PIN_INPUT | MUX_MODE0) /* gpmc_ad4 */ - DRA7XX_CORE_IOPAD(0x3414, PIN_INPUT | MUX_MODE0) /* gpmc_ad5 */ - DRA7XX_CORE_IOPAD(0x3418, PIN_INPUT | MUX_MODE0) /* gpmc_ad6 */ - DRA7XX_CORE_IOPAD(0x341c, PIN_INPUT | MUX_MODE0) /* gpmc_ad7 */ - DRA7XX_CORE_IOPAD(0x3420, PIN_INPUT | MUX_MODE0) /* gpmc_ad8 */ - DRA7XX_CORE_IOPAD(0x3424, PIN_INPUT | MUX_MODE0) /* gpmc_ad9 */ - DRA7XX_CORE_IOPAD(0x3428, PIN_INPUT | MUX_MODE0) /* gpmc_ad10 */ - DRA7XX_CORE_IOPAD(0x342c, PIN_INPUT | MUX_MODE0) /* gpmc_ad11 */ - DRA7XX_CORE_IOPAD(0x3430, PIN_INPUT | MUX_MODE0) /* gpmc_ad12 */ - DRA7XX_CORE_IOPAD(0x3434, PIN_INPUT | MUX_MODE0) /* gpmc_ad13 */ - DRA7XX_CORE_IOPAD(0x3438, PIN_INPUT | MUX_MODE0) /* gpmc_ad14 */ - DRA7XX_CORE_IOPAD(0x343c, PIN_INPUT | MUX_MODE0) /* gpmc_ad15 */ - DRA7XX_CORE_IOPAD(0x34b4, PIN_OUTPUT | MUX_MODE0) /* gpmc_cs0 */ - DRA7XX_CORE_IOPAD(0x34c4, PIN_OUTPUT | MUX_MODE0) /* gpmc_advn_ale */ - DRA7XX_CORE_IOPAD(0x34cc, PIN_OUTPUT | MUX_MODE0) /* gpmc_wen */ - DRA7XX_CORE_IOPAD(0x34c8, PIN_OUTPUT | MUX_MODE0) /* gpmc_oen_ren */ - DRA7XX_CORE_IOPAD(0x34d0, PIN_OUTPUT | MUX_MODE0) /* gpmc_ben0 */ - DRA7XX_CORE_IOPAD(0x34d8, PIN_INPUT | MUX_MODE0) /* gpmc_wait0 */ - >; - }; - - usb1_pins: pinmux_usb1_pins { - pinctrl-single,pins = < - DRA7XX_CORE_IOPAD(0x3680, PIN_INPUT_SLEW | MUX_MODE0) /* usb1_drvvbus */ - >; - }; - - usb2_pins: pinmux_usb2_pins { - pinctrl-single,pins = < - DRA7XX_CORE_IOPAD(0x3684, PIN_INPUT_SLEW | MUX_MODE0) /* usb2_drvvbus */ - >; - }; - - tps65917_pins_default: tps65917_pins_default { - pinctrl-single,pins = < - DRA7XX_CORE_IOPAD(0x3824, PIN_INPUT_PULLUP | MUX_MODE1) /* wakeup3.sys_nirq1 */ - >; - }; - - mmc1_pins_default: mmc1_pins_default { - pinctrl-single,pins = < - DRA7XX_CORE_IOPAD(0x376c, PIN_INPUT | MUX_MODE14) /* mmc1sdcd.gpio219 */ - DRA7XX_CORE_IOPAD(0x3754, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_clk.clk */ - DRA7XX_CORE_IOPAD(0x3758, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_cmd.cmd */ - DRA7XX_CORE_IOPAD(0x375c, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_dat0.dat0 */ - DRA7XX_CORE_IOPAD(0x3760, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_dat1.dat1 */ - DRA7XX_CORE_IOPAD(0x3764, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_dat2.dat2 */ - DRA7XX_CORE_IOPAD(0x3768, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_dat3.dat3 */ - >; - }; - - mmc2_pins_default: mmc2_pins_default { - pinctrl-single,pins = < - DRA7XX_CORE_IOPAD(0x349c, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a23.mmc2_clk */ - DRA7XX_CORE_IOPAD(0x34b0, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_cs1.mmc2_cmd */ - DRA7XX_CORE_IOPAD(0x34a0, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a24.mmc2_dat0 */ - DRA7XX_CORE_IOPAD(0x34a4, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a25.mmc2_dat1 */ - DRA7XX_CORE_IOPAD(0x34a8, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a26.mmc2_dat2 */ - DRA7XX_CORE_IOPAD(0x34ac, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a27.mmc2_dat3 */ - DRA7XX_CORE_IOPAD(0x348c, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a19.mmc2_dat4 */ - DRA7XX_CORE_IOPAD(0x3490, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a20.mmc2_dat5 */ - DRA7XX_CORE_IOPAD(0x3494, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a21.mmc2_dat6 */ - DRA7XX_CORE_IOPAD(0x3498, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a22.mmc2_dat7 */ - >; - }; - - dcan1_pins_default: dcan1_pins_default { - pinctrl-single,pins = < - DRA7XX_CORE_IOPAD(0x37d0, PIN_OUTPUT_PULLUP | MUX_MODE0) /* dcan1_tx */ - DRA7XX_CORE_IOPAD(0x3818, PULL_UP | MUX_MODE1) /* wakeup0.dcan1_rx */ - >; - }; - - dcan1_pins_sleep: dcan1_pins_sleep { - pinctrl-single,pins = < - DRA7XX_CORE_IOPAD(0x37d0, MUX_MODE15 | PULL_UP) /* dcan1_tx.off */ - DRA7XX_CORE_IOPAD(0x3818, MUX_MODE15 | PULL_UP) /* wakeup0.off */ - >; - }; - - qspi1_pins: pinmux_qspi1_pins { - pinctrl-single,pins = < - DRA7XX_CORE_IOPAD(0x3474, PIN_OUTPUT | MUX_MODE1) /* gpmc_a13.qspi1_rtclk */ - DRA7XX_CORE_IOPAD(0x3478, PIN_INPUT | MUX_MODE1) /* gpmc_a14.qspi1_d3 */ - DRA7XX_CORE_IOPAD(0x347c, PIN_INPUT | MUX_MODE1) /* gpmc_a15.qspi1_d2 */ - DRA7XX_CORE_IOPAD(0x3480, PIN_INPUT | MUX_MODE1) /* gpmc_a16.qspi1_d1 */ - DRA7XX_CORE_IOPAD(0x3484, PIN_INPUT | MUX_MODE1) /* gpmc_a17.qspi1_d0 */ - DRA7XX_CORE_IOPAD(0x3488, PIN_OUTPUT | MUX_MODE1) /* qpmc_a18.qspi1_sclk */ - DRA7XX_CORE_IOPAD(0x34b8, PIN_OUTPUT | MUX_MODE1) /* gpmc_cs2.qspi1_cs0 */ - >; - }; - - hdmi_pins: pinmux_hdmi_pins { - pinctrl-single,pins = < - DRA7XX_CORE_IOPAD(0x3808, PIN_INPUT | MUX_MODE1) /* i2c2_sda.hdmi1_ddc_scl */ - DRA7XX_CORE_IOPAD(0x380c, PIN_INPUT | MUX_MODE1) /* i2c2_scl.hdmi1_ddc_sda */ - >; - }; - - tpd12s015_pins: pinmux_tpd12s015_pins { - pinctrl-single,pins = < - DRA7XX_CORE_IOPAD(0x37b8, PIN_INPUT_PULLDOWN | MUX_MODE14) /* gpio7_12 HPD */ - >; - }; - - atl_pins: pinmux_atl_pins { - pinctrl-single,pins = < - DRA7XX_CORE_IOPAD(0x3698, PIN_OUTPUT | MUX_MODE5) /* xref_clk1.atl_clk1 */ - DRA7XX_CORE_IOPAD(0x369c, PIN_OUTPUT | MUX_MODE5) /* xref_clk2.atl_clk2 */ - >; - }; - - mcasp3_pins: pinmux_mcasp3_pins { - pinctrl-single,pins = < - DRA7XX_CORE_IOPAD(0x3724, PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* mcasp3_aclkx */ - DRA7XX_CORE_IOPAD(0x3728, PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* mcasp3_fsx */ - DRA7XX_CORE_IOPAD(0x372c, PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* mcasp3_axr0 */ - DRA7XX_CORE_IOPAD(0x3730, PIN_INPUT_PULLDOWN | MUX_MODE0) /* mcasp3_axr1 */ - >; - }; - - mcasp3_sleep_pins: pinmux_mcasp3_sleep_pins { - pinctrl-single,pins = < - DRA7XX_CORE_IOPAD(0x3724, PIN_INPUT_PULLDOWN | MUX_MODE15) - DRA7XX_CORE_IOPAD(0x3728, PIN_INPUT_PULLDOWN | MUX_MODE15) - DRA7XX_CORE_IOPAD(0x372c, PIN_INPUT_PULLDOWN | MUX_MODE15) - DRA7XX_CORE_IOPAD(0x3730, PIN_INPUT_PULLDOWN | MUX_MODE15) - >; - }; +&hdmi { + vdda-supply = <&ldo3_reg>; }; -&i2c1 { - status = "okay"; - pinctrl-names = "default"; - pinctrl-0 = <&i2c1_pins>; - clock-frequency = <400000>; - - tps65917: tps65917@58 { - compatible = "ti,tps65917"; - reg = <0x58>; - - pinctrl-names = "default"; - pinctrl-0 = <&tps65917_pins_default>; - - interrupts = ; /* IRQ_SYS_1N */ - interrupt-controller; - #interrupt-cells = <2>; - - ti,system-power-controller; - - tps65917_pmic { - compatible = "ti,tps65917-pmic"; - - regulators { - smps1_reg: smps1 { - /* VDD_MPU */ - regulator-name = "smps1"; - regulator-min-microvolt = <850000>; - regulator-max-microvolt = <1250000>; - regulator-always-on; - regulator-boot-on; - }; - - smps2_reg: smps2 { - /* VDD_CORE */ - regulator-name = "smps2"; - regulator-min-microvolt = <850000>; - regulator-max-microvolt = <1060000>; - regulator-boot-on; - regulator-always-on; - }; - - smps3_reg: smps3 { - /* VDD_GPU IVA DSPEVE */ - regulator-name = "smps3"; - regulator-min-microvolt = <850000>; - regulator-max-microvolt = <1250000>; - regulator-boot-on; - regulator-always-on; - }; - - smps4_reg: smps4 { - /* VDDS1V8 */ - regulator-name = "smps4"; - regulator-min-microvolt = <1800000>; - regulator-max-microvolt = <1800000>; - regulator-always-on; - regulator-boot-on; - }; - - smps5_reg: smps5 { - /* VDD_DDR */ - regulator-name = "smps5"; - regulator-min-microvolt = <1350000>; - regulator-max-microvolt = <1350000>; - regulator-boot-on; - regulator-always-on; - }; - - ldo1_reg: ldo1 { - /* LDO1_OUT --> SDIO */ - regulator-name = "ldo1"; - regulator-min-microvolt = <1800000>; - regulator-max-microvolt = <3300000>; - regulator-always-on; - regulator-boot-on; - regulator-allow-bypass; - }; - - ldo2_reg: ldo2 { - /* LDO2_OUT --> TP1017 (UNUSED) */ - regulator-name = "ldo2"; - regulator-min-microvolt = <1800000>; - regulator-max-microvolt = <3300000>; - regulator-allow-bypass; - }; - - ldo3_reg: ldo3 { - /* VDDA_1V8_PHY */ - regulator-name = "ldo3"; - regulator-min-microvolt = <1800000>; - regulator-max-microvolt = <1800000>; - regulator-boot-on; - regulator-always-on; - }; - - ldo5_reg: ldo5 { - /* VDDA_1V8_PLL */ - regulator-name = "ldo5"; - regulator-min-microvolt = <1800000>; - regulator-max-microvolt = <1800000>; - regulator-always-on; - regulator-boot-on; - }; - - ldo4_reg: ldo4 { - /* VDDA_3V_USB: VDDA_USBHS33 */ - regulator-name = "ldo4"; - regulator-min-microvolt = <3300000>; - regulator-max-microvolt = <3300000>; - regulator-boot-on; - }; - }; - }; - - tps65917_power_button { - compatible = "ti,palmas-pwrbutton"; - interrupt-parent = <&tps65917>; - interrupts = <1 IRQ_TYPE_NONE>; - wakeup-source; - ti,palmas-long-press-seconds = <6>; - }; - }; - - pcf_gpio_21: gpio@21 { - compatible = "nxp,pcf8575"; - reg = <0x21>; - lines-initial-states = <0x1408>; - gpio-controller; - #gpio-cells = <2>; - interrupt-parent = <&gpio6>; - interrupts = <11 IRQ_TYPE_EDGE_FALLING>; - interrupt-controller; - #interrupt-cells = <2>; - }; - - tlv320aic3106: tlv320aic3106@19 { - #sound-dai-cells = <0>; - compatible = "ti,tlv320aic3106"; - reg = <0x19>; - adc-settle-ms = <40>; - ai3x-micbias-vg = <1>; /* 2.0V */ - status = "okay"; - - /* Regulators */ - AVDD-supply = <&evm_3v3>; - IOVDD-supply = <&evm_3v3>; - DRVDD-supply = <&evm_3v3>; - DVDD-supply = <&aic_dvdd>; - }; -}; - -&i2c5 { - status = "okay"; - pinctrl-names = "default"; - pinctrl-0 = <&i2c5_pins>; - clock-frequency = <400000>; - - pcf_hdmi: pcf8575@26 { - compatible = "nxp,pcf8575"; - reg = <0x26>; - gpio-controller; - #gpio-cells = <2>; - /* - * initial state is used here to keep the mdio interface - * selected on RU89 through SEL_VIN4_MUX_S0, VIN2_S1 and - * VIN2_S0 driven high otherwise Ethernet stops working - * VIN6_SEL_S0 is low, thus selecting McASP3 over VIN6 - */ - lines-initial-states = <0x0f2b>; - - p1 { - /* vin6_sel_s0: high: VIN6, low: audio */ - gpio-hog; - gpios = <1 GPIO_ACTIVE_HIGH>; - output-low; - line-name = "vin6_sel_s0"; - }; - }; -}; - -&uart1 { - status = "okay"; - interrupts-extended = <&crossbar_mpu GIC_SPI 67 IRQ_TYPE_LEVEL_HIGH>, - <&dra7_pmx_core 0x3e0>; -}; - -&elm { - status = "okay"; -}; - -&gpmc { - status = "okay"; - pinctrl-names = "default"; - pinctrl-0 = <&nand_default>; - ranges = <0 0 0x08000000 0x01000000>; /* minimum GPMC partition = 16MB */ - nand@0,0 { - /* To use NAND, DIP switch SW5 must be set like so: - * SW5.1 (NAND_SELn) = ON (LOW) - * SW5.9 (GPMC_WPN) = OFF (HIGH) - */ - compatible = "ti,omap2-nand"; - reg = <0 0 4>; /* device IO registers */ - interrupt-parent = <&gpmc>; - interrupts = <0 IRQ_TYPE_NONE>, /* fifoevent */ - <1 IRQ_TYPE_NONE>; /* termcount */ - rb-gpios = <&gpmc 0 GPIO_ACTIVE_HIGH>; /* gpmc_wait0 pin */ - ti,nand-ecc-opt = "bch8"; - ti,elm-id = <&elm>; - nand-bus-width = <16>; - gpmc,device-width = <2>; - gpmc,sync-clk-ps = <0>; - gpmc,cs-on-ns = <0>; - gpmc,cs-rd-off-ns = <80>; - gpmc,cs-wr-off-ns = <80>; - gpmc,adv-on-ns = <0>; - gpmc,adv-rd-off-ns = <60>; - gpmc,adv-wr-off-ns = <60>; - gpmc,we-on-ns = <10>; - gpmc,we-off-ns = <50>; - gpmc,oe-on-ns = <4>; - gpmc,oe-off-ns = <40>; - gpmc,access-ns = <40>; - gpmc,wr-access-ns = <80>; - gpmc,rd-cycle-ns = <80>; - gpmc,wr-cycle-ns = <80>; - gpmc,bus-turnaround-ns = <0>; - gpmc,cycle2cycle-delay-ns = <0>; - gpmc,clk-activation-ns = <0>; - gpmc,wr-data-mux-bus-ns = <0>; - /* MTD partition table */ - /* All SPL-* partitions are sized to minimal length - * which can be independently programmable. For - * NAND flash this is equal to size of erase-block */ - #address-cells = <1>; - #size-cells = <1>; - partition@0 { - label = "NAND.SPL"; - reg = <0x00000000 0x000020000>; - }; - partition@1 { - label = "NAND.SPL.backup1"; - reg = <0x00020000 0x00020000>; - }; - partition@2 { - label = "NAND.SPL.backup2"; - reg = <0x00040000 0x00020000>; - }; - partition@3 { - label = "NAND.SPL.backup3"; - reg = <0x00060000 0x00020000>; - }; - partition@4 { - label = "NAND.u-boot-spl-os"; - reg = <0x00080000 0x00040000>; - }; - partition@5 { - label = "NAND.u-boot"; - reg = <0x000c0000 0x00100000>; - }; - partition@6 { - label = "NAND.u-boot-env"; - reg = <0x001c0000 0x00020000>; - }; - partition@7 { - label = "NAND.u-boot-env.backup1"; - reg = <0x001e0000 0x00020000>; - }; - partition@8 { - label = "NAND.kernel"; - reg = <0x00200000 0x00800000>; - }; - partition@9 { - label = "NAND.file-system"; - reg = <0x00a00000 0x0f600000>; - }; - }; -}; - -&usb2_phy1 { - phy-supply = <&ldo4_reg>; -}; - -&usb2_phy2 { - phy-supply = <&ldo4_reg>; -}; - -&omap_dwc3_1 { - extcon = <&extcon_usb1>; -}; - -&omap_dwc3_2 { - extcon = <&extcon_usb2>; -}; - -&usb1 { - dr_mode = "peripheral"; - pinctrl-names = "default"; - pinctrl-0 = <&usb1_pins>; -}; - -&usb2 { - dr_mode = "host"; - pinctrl-names = "default"; - pinctrl-0 = <&usb2_pins>; -}; - -&mmc1 { - status = "okay"; - pinctrl-names = "default"; - pinctrl-0 = <&mmc1_pins_default>; - vmmc-supply = <&evm_3v3_sd>; - vmmc_aux-supply = <&ldo1_reg>; - bus-width = <4>; - /* - * SDCD signal is not being used here - using the fact that GPIO mode - * is a viable alternative - */ - cd-gpios = <&gpio6 27 GPIO_ACTIVE_LOW>; - max-frequency = <192000000>; -}; - -&mmc2 { - /* SW5-3 in ON position */ - status = "okay"; - pinctrl-names = "default"; - pinctrl-0 = <&mmc2_pins_default>; - - vmmc-supply = <&evm_3v3>; - bus-width = <8>; - ti,non-removable; - max-frequency = <192000000>; -}; - -&dra7_pmx_core { - cpsw_default: cpsw_default { - pinctrl-single,pins = < - /* Slave 2 */ - DRA7XX_CORE_IOPAD(0x3598, PIN_OUTPUT | MUX_MODE3) /* vin2a_d12.rgmii1_txc */ - DRA7XX_CORE_IOPAD(0x359c, PIN_OUTPUT | MUX_MODE3) /* vin2a_d13.rgmii1_tctl */ - DRA7XX_CORE_IOPAD(0x35a0, PIN_OUTPUT | MUX_MODE3) /* vin2a_d14.rgmii1_td3 */ - DRA7XX_CORE_IOPAD(0x35a4, PIN_OUTPUT | MUX_MODE3) /* vin2a_d15.rgmii1_td2 */ - DRA7XX_CORE_IOPAD(0x35a8, PIN_OUTPUT | MUX_MODE3) /* vin2a_d16.rgmii1_td1 */ - DRA7XX_CORE_IOPAD(0x35ac, PIN_OUTPUT | MUX_MODE3) /* vin2a_d17.rgmii1_td0 */ - DRA7XX_CORE_IOPAD(0x35b0, PIN_INPUT | MUX_MODE3) /* vin2a_d18.rgmii1_rclk */ - DRA7XX_CORE_IOPAD(0x35b4, PIN_INPUT | MUX_MODE3) /* vin2a_d19.rgmii1_rctl */ - DRA7XX_CORE_IOPAD(0x35b8, PIN_INPUT | MUX_MODE3) /* vin2a_d20.rgmii1_rd3 */ - DRA7XX_CORE_IOPAD(0x35bc, PIN_INPUT | MUX_MODE3) /* vin2a_d21.rgmii1_rd2 */ - DRA7XX_CORE_IOPAD(0x35c0, PIN_INPUT | MUX_MODE3) /* vin2a_d22.rgmii1_rd1 */ - DRA7XX_CORE_IOPAD(0x35c4, PIN_INPUT | MUX_MODE3) /* vin2a_d23.rgmii1_rd0 */ - >; - - }; - - cpsw_sleep: cpsw_sleep { - pinctrl-single,pins = < - /* Slave 2 */ - DRA7XX_CORE_IOPAD(0x3598, MUX_MODE15) - DRA7XX_CORE_IOPAD(0x359c, MUX_MODE15) - DRA7XX_CORE_IOPAD(0x35a0, MUX_MODE15) - DRA7XX_CORE_IOPAD(0x35a4, MUX_MODE15) - DRA7XX_CORE_IOPAD(0x35a8, MUX_MODE15) - DRA7XX_CORE_IOPAD(0x35ac, MUX_MODE15) - DRA7XX_CORE_IOPAD(0x35b0, MUX_MODE15) - DRA7XX_CORE_IOPAD(0x35b4, MUX_MODE15) - DRA7XX_CORE_IOPAD(0x35b8, MUX_MODE15) - DRA7XX_CORE_IOPAD(0x35bc, MUX_MODE15) - DRA7XX_CORE_IOPAD(0x35c0, MUX_MODE15) - DRA7XX_CORE_IOPAD(0x35c4, MUX_MODE15) - >; - }; - - davinci_mdio_default: davinci_mdio_default { - pinctrl-single,pins = < - /* MDIO */ - DRA7XX_CORE_IOPAD(0x363c, PIN_OUTPUT_PULLUP | MUX_MODE0) /* mdio_d.mdio_d */ - DRA7XX_CORE_IOPAD(0x3640, PIN_INPUT_PULLUP | MUX_MODE0) /* mdio_clk.mdio_clk */ - >; - }; - - davinci_mdio_sleep: davinci_mdio_sleep { - pinctrl-single,pins = < - DRA7XX_CORE_IOPAD(0x363c, MUX_MODE15) - DRA7XX_CORE_IOPAD(0x3640, MUX_MODE15) - >; - }; +&pcf_gpio_21 { + interrupt-parent = <&gpio6>; + interrupts = <11 IRQ_TYPE_EDGE_FALLING>; }; &mac { - status = "okay"; - pinctrl-names = "default", "sleep"; - pinctrl-0 = <&cpsw_default>; - pinctrl-1 = <&cpsw_sleep>; slaves = <1>; mode-gpios = <&pcf_gpio_21 4 GPIO_ACTIVE_HIGH>; }; @@ -698,160 +43,3 @@ phy_id = <&davinci_mdio>, <3>; phy-mode = "rgmii"; }; - -&davinci_mdio { - pinctrl-names = "default", "sleep"; - pinctrl-0 = <&davinci_mdio_default>; - pinctrl-1 = <&davinci_mdio_sleep>; -}; - -&dcan1 { - status = "ok"; - pinctrl-names = "default", "sleep", "active"; - pinctrl-0 = <&dcan1_pins_sleep>; - pinctrl-1 = <&dcan1_pins_sleep>; - pinctrl-2 = <&dcan1_pins_default>; -}; - -&qspi { - status = "okay"; - pinctrl-names = "default"; - pinctrl-0 = <&qspi1_pins>; - - spi-max-frequency = <48000000>; - m25p80@0 { - compatible = "s25fl256s1"; - spi-max-frequency = <48000000>; - reg = <0>; - spi-tx-bus-width = <1>; - spi-rx-bus-width = <4>; - spi-cpol; - spi-cpha; - #address-cells = <1>; - #size-cells = <1>; - - /* MTD partition table. - * The ROM checks the first four physical blocks - * for a valid file to boot and the flash here is - * 64KiB block size. - */ - partition@0 { - label = "QSPI.SPL"; - reg = <0x00000000 0x000010000>; - }; - partition@1 { - label = "QSPI.SPL.backup1"; - reg = <0x00010000 0x00010000>; - }; - partition@2 { - label = "QSPI.SPL.backup2"; - reg = <0x00020000 0x00010000>; - }; - partition@3 { - label = "QSPI.SPL.backup3"; - reg = <0x00030000 0x00010000>; - }; - partition@4 { - label = "QSPI.u-boot"; - reg = <0x00040000 0x00100000>; - }; - partition@5 { - label = "QSPI.u-boot-spl-os"; - reg = <0x00140000 0x00080000>; - }; - partition@6 { - label = "QSPI.u-boot-env"; - reg = <0x001c0000 0x00010000>; - }; - partition@7 { - label = "QSPI.u-boot-env.backup1"; - reg = <0x001d0000 0x0010000>; - }; - partition@8 { - label = "QSPI.kernel"; - reg = <0x001e0000 0x0800000>; - }; - partition@9 { - label = "QSPI.file-system"; - reg = <0x009e0000 0x01620000>; - }; - }; -}; - -&dss { - status = "ok"; - - vdda_video-supply = <&ldo5_reg>; -}; - -&hdmi { - status = "ok"; - vdda-supply = <&ldo3_reg>; - - pinctrl-names = "default"; - pinctrl-0 = <&hdmi_pins>; - - port { - hdmi_out: endpoint { - remote-endpoint = <&tpd12s015_in>; - }; - }; -}; - -&atl { - pinctrl-names = "default"; - pinctrl-0 = <&atl_pins>; - - assigned-clocks = <&abe_dpll_sys_clk_mux>, - <&atl_gfclk_mux>, - <&dpll_abe_ck>, - <&dpll_abe_m2x2_ck>, - <&atl_clkin2_ck>; - assigned-clock-parents = <&sys_clkin2>, <&dpll_abe_m2_ck>; - assigned-clock-rates = <0>, <0>, <180633600>, <361267200>, <5644800>; - - status = "okay"; - - atl2 { - bws = ; - aws = ; - }; -}; - -&mcasp3 { - #sound-dai-cells = <0>; - pinctrl-names = "default", "sleep"; - pinctrl-0 = <&mcasp3_pins>; - pinctrl-1 = <&mcasp3_sleep_pins>; - - assigned-clocks = <&mcasp3_ahclkx_mux>; - assigned-clock-parents = <&atl_clkin2_ck>; - - status = "okay"; - - op-mode = <0>; /* MCASP_IIS_MODE */ - tdm-slots = <2>; - /* 4 serializer */ - serial-dir = < /* 0: INACTIVE, 1: TX, 2: RX */ - 1 2 0 0 - >; - tx-num-evt = <32>; - rx-num-evt = <32>; -}; - -&mailbox5 { - status = "okay"; - mbox_ipu1_ipc3x: mbox_ipu1_ipc3x { - status = "okay"; - }; - mbox_dsp1_ipc3x: mbox_dsp1_ipc3x { - status = "okay"; - }; -}; - -&mailbox6 { - status = "okay"; - mbox_ipu2_ipc3x: mbox_ipu2_ipc3x { - status = "okay"; - }; -};