arm64: dts: qcom: Add support for OnePlus 5/5T
Add device trees for OnePlus 5 (cheeseburger) and 5T (dumpling) MSM8998 SoC smartphones with initial support included for: - UFS internal storage - USB peripheral mode - Display - Touch - Bluetooth - Hall effect sensor - Power and volume buttons - Capacitive keypad button backlight (on cheeseburger) Signed-off-by: Jami Kettunen <jamipkettunen@gmail.com> Link: https://lore.kernel.org/r/20210406010708.2376807-2-jamipkettunen@gmail.com Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
This commit is contained in:
Jami Kettunen
Bjorn Andersson
parent
03041cd25d
commit
47498916af
arch/arm64/boot/dts/qcom
|
|
@ -27,6 +27,8 @@ dtb-$(CONFIG_ARCH_QCOM) += msm8998-asus-novago-tp370ql.dtb
|
|||
dtb-$(CONFIG_ARCH_QCOM) += msm8998-hp-envy-x2.dtb
|
||||
dtb-$(CONFIG_ARCH_QCOM) += msm8998-lenovo-miix-630.dtb
|
||||
dtb-$(CONFIG_ARCH_QCOM) += msm8998-mtp.dtb
|
||||
dtb-$(CONFIG_ARCH_QCOM) += msm8998-oneplus-cheeseburger.dtb
|
||||
dtb-$(CONFIG_ARCH_QCOM) += msm8998-oneplus-dumpling.dtb
|
||||
dtb-$(CONFIG_ARCH_QCOM) += qcs404-evb-1000.dtb
|
||||
dtb-$(CONFIG_ARCH_QCOM) += qcs404-evb-4000.dtb
|
||||
dtb-$(CONFIG_ARCH_QCOM) += qrb5165-rb5.dtb
|
||||
|
|
|
|||
|
|
@ -0,0 +1,42 @@
|
|||
// SPDX-License-Identifier: BSD-3-Clause
|
||||
/*
|
||||
* OnePlus 5 (cheeseburger) device tree
|
||||
*
|
||||
* Copyright (c) 2021, Jami Kettunen <jamipkettunen@gmail.com>
|
||||
*/
|
||||
|
||||
#include <dt-bindings/leds/common.h>
|
||||
#include "msm8998-oneplus-common.dtsi"
|
||||
|
||||
/ {
|
||||
model = "OnePlus 5";
|
||||
compatible = "oneplus,cheeseburger", "qcom,msm8998";
|
||||
/* Required for bootloader to select correct board */
|
||||
qcom,board-id = <8 0 16859 23>;
|
||||
|
||||
/* Capacitive keypad button backlight */
|
||||
leds {
|
||||
compatible = "gpio-leds";
|
||||
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&button_backlight_default>;
|
||||
|
||||
button-backlight {
|
||||
gpios = <&pmi8998_gpio 5 GPIO_ACTIVE_HIGH>;
|
||||
color = <LED_COLOR_ID_WHITE>;
|
||||
function = LED_FUNCTION_KBD_BACKLIGHT;
|
||||
default-state = "off";
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&pmi8998_gpio {
|
||||
button_backlight_default: button-backlight-default {
|
||||
pinconf {
|
||||
pins = "gpio5";
|
||||
function = "normal";
|
||||
bias-pull-down;
|
||||
qcom,drive-strength = <PMIC_GPIO_STRENGTH_NO>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
|
@ -0,0 +1,514 @@
|
|||
// SPDX-License-Identifier: BSD-3-Clause
|
||||
/*
|
||||
* OnePlus 5(T) (cheeseburger / dumpling) common device tree source based on msm8998-mtp.dtsi
|
||||
*
|
||||
* Copyright (c) 2021, Jami Kettunen <jamipkettunen@gmail.com>
|
||||
* Copyright (c) 2016, The Linux Foundation. All rights reserved.
|
||||
*/
|
||||
|
||||
/dts-v1/;
|
||||
|
||||
#include <dt-bindings/gpio/gpio.h>
|
||||
#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
|
||||
#include "msm8998.dtsi"
|
||||
#include "pm8998.dtsi"
|
||||
#include "pmi8998.dtsi"
|
||||
#include "pm8005.dtsi"
|
||||
|
||||
/ {
|
||||
/* Required for bootloader to select correct board */
|
||||
qcom,msm-id = <292 0x20001>; /* 8998 v2.1 */
|
||||
|
||||
chosen {
|
||||
#address-cells = <2>;
|
||||
#size-cells = <2>;
|
||||
ranges;
|
||||
|
||||
/* Use display framebuffer setup by the UEFI XBL bootloader for simplefb */
|
||||
framebuffer0: framebuffer@9d400000 {
|
||||
compatible = "simple-framebuffer";
|
||||
reg = <0x0 0x9d400000 0x0 0x2400000>;
|
||||
width = <1080>;
|
||||
height = <1920>;
|
||||
stride = <(1080 * 4)>;
|
||||
format = "a8r8g8b8";
|
||||
};
|
||||
};
|
||||
|
||||
reserved-memory {
|
||||
/* Bootloader display framebuffer region */
|
||||
cont_splash_mem: memory@9d400000 {
|
||||
reg = <0x0 0x9d400000 0x0 0x2400000>;
|
||||
no-map;
|
||||
};
|
||||
|
||||
/* For getting crash logs using Android downstream kernels */
|
||||
ramoops@ac000000 {
|
||||
compatible = "ramoops";
|
||||
reg = <0x0 0xac000000 0x0 0x200000>;
|
||||
console-size = <0x80000>;
|
||||
pmsg-size = <0x40000>;
|
||||
record-size = <0x8000>;
|
||||
ftrace-size = <0x20000>;
|
||||
};
|
||||
|
||||
/*
|
||||
* The following memory regions on downstream are "dynamically allocated"
|
||||
* but given the same addresses every time. Hard code them as these addresses
|
||||
* are where the OnePlus signed firmware expects them to be.
|
||||
*/
|
||||
ipa_fws_region: ipa@f6800000 {
|
||||
compatible = "shared-dma-pool";
|
||||
reg = <0x0 0xf6800000 0x0 0x5000>;
|
||||
no-map;
|
||||
};
|
||||
zap_shader_region: gpu@f6900000 {
|
||||
compatible = "shared-dma-pool";
|
||||
reg = <0x0 0xf6900000 0x0 0x2000>;
|
||||
no-map;
|
||||
};
|
||||
};
|
||||
|
||||
gpio-keys {
|
||||
compatible = "gpio-keys";
|
||||
label = "Volume buttons";
|
||||
autorepeat;
|
||||
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&vol_keys_default>;
|
||||
|
||||
vol-down {
|
||||
label = "Volume down";
|
||||
gpios = <&pm8998_gpio 5 GPIO_ACTIVE_LOW>;
|
||||
linux,code = <KEY_VOLUMEDOWN>;
|
||||
debounce-interval = <15>;
|
||||
wakeup-source;
|
||||
};
|
||||
|
||||
vol-up {
|
||||
label = "Volume up";
|
||||
gpios = <&pm8998_gpio 6 GPIO_ACTIVE_LOW>;
|
||||
linux,code = <KEY_VOLUMEUP>;
|
||||
debounce-interval = <15>;
|
||||
wakeup-source;
|
||||
};
|
||||
};
|
||||
|
||||
gpio-hall-sensor {
|
||||
compatible = "gpio-keys";
|
||||
label = "Hall effect sensor";
|
||||
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&hall_sensor_default>;
|
||||
|
||||
hall-sensor {
|
||||
label = "Hall Effect Sensor";
|
||||
gpios = <&tlmm 124 GPIO_ACTIVE_LOW>;
|
||||
linux,input-type = <EV_SW>;
|
||||
linux,code = <SW_LID>;
|
||||
linux,can-disable;
|
||||
wakeup-source;
|
||||
};
|
||||
};
|
||||
|
||||
vph_pwr: vph-pwr-regulator {
|
||||
compatible = "regulator-fixed";
|
||||
regulator-name = "vph_pwr";
|
||||
regulator-always-on;
|
||||
regulator-boot-on;
|
||||
};
|
||||
};
|
||||
|
||||
/*
|
||||
* OnePlus' ADSP firmware requires 30 MiB in total, so increase the adsp_mem
|
||||
* region by 4 MiB to account for this while relocating the other now
|
||||
* conflicting memory nodes accordingly.
|
||||
*/
|
||||
&adsp_mem {
|
||||
reg = <0x0 0x8b200000 0x0 0x1e00000>;
|
||||
};
|
||||
&mpss_mem {
|
||||
reg = <0x0 0x8d000000 0x0 0x7000000>;
|
||||
};
|
||||
&venus_mem {
|
||||
reg = <0x0 0x94000000 0x0 0x500000>;
|
||||
};
|
||||
&mba_mem {
|
||||
reg = <0x0 0x94500000 0x0 0x200000>;
|
||||
};
|
||||
&slpi_mem {
|
||||
reg = <0x0 0x94700000 0x0 0xf00000>;
|
||||
};
|
||||
&ipa_fw_mem {
|
||||
reg = <0x0 0x95600000 0x0 0x10000>;
|
||||
};
|
||||
&ipa_gsi_mem {
|
||||
reg = <0x0 0x95610000 0x0 0x5000>;
|
||||
};
|
||||
&gpu_mem {
|
||||
reg = <0x0 0x95615000 0x0 0x100000>;
|
||||
};
|
||||
&wlan_msa_mem {
|
||||
reg = <0x0 0x95715000 0x0 0x100000>;
|
||||
};
|
||||
|
||||
&blsp1_i2c5 {
|
||||
status = "okay";
|
||||
|
||||
touchscreen@20 {
|
||||
compatible = "syna,rmi4-i2c";
|
||||
reg = <0x20>;
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
|
||||
interrupt-parent = <&tlmm>;
|
||||
interrupts = <125 IRQ_TYPE_EDGE_FALLING>;
|
||||
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&ts_int_active &ts_reset_active>;
|
||||
|
||||
vdd-supply = <&vreg_l28_3p0>;
|
||||
vio-supply = <&vreg_l6a_1p8>;
|
||||
|
||||
syna,reset-delay-ms = <20>;
|
||||
syna,startup-delay-ms = <20>;
|
||||
|
||||
rmi4-f01@1 {
|
||||
reg = <0x01>;
|
||||
syna,nosleep-mode = <1>;
|
||||
};
|
||||
|
||||
rmi4_f12: rmi4-f12@12 {
|
||||
reg = <0x12>;
|
||||
syna,rezero-wait-ms = <20>;
|
||||
syna,sensor-type = <1>;
|
||||
touchscreen-x-mm = <68>;
|
||||
touchscreen-y-mm = <122>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&blsp1_uart3 {
|
||||
status = "okay";
|
||||
|
||||
bluetooth {
|
||||
compatible = "qcom,wcn3990-bt";
|
||||
|
||||
vddio-supply = <&vreg_s4a_1p8>;
|
||||
vddxo-supply = <&vreg_l7a_1p8>;
|
||||
vddrf-supply = <&vreg_l17a_1p3>;
|
||||
vddch0-supply = <&vreg_l25a_3p3>;
|
||||
max-speed = <3200000>;
|
||||
};
|
||||
};
|
||||
|
||||
&blsp1_uart3_on {
|
||||
rx {
|
||||
/delete-property/ bias-disable;
|
||||
/*
|
||||
* Configure a pull-up on 46 (RX). This is needed to
|
||||
* avoid garbage data when the TX pin of the Bluetooth
|
||||
* module is in tri-state (module powered off or not
|
||||
* driving the signal yet).
|
||||
*/
|
||||
bias-pull-up;
|
||||
};
|
||||
|
||||
cts {
|
||||
/delete-property/ bias-disable;
|
||||
/*
|
||||
* Configure a pull-down on 47 (CTS) to match the pull
|
||||
* of the Bluetooth module.
|
||||
*/
|
||||
bias-pull-down;
|
||||
};
|
||||
};
|
||||
|
||||
&blsp2_uart1 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&pm8005_lsid1 {
|
||||
pm8005-regulators {
|
||||
compatible = "qcom,pm8005-regulators";
|
||||
|
||||
vdd_s1-supply = <&vph_pwr>;
|
||||
|
||||
pm8005_s1: s1 { /* VDD_GFX supply */
|
||||
regulator-min-microvolt = <524000>;
|
||||
regulator-max-microvolt = <1100000>;
|
||||
regulator-enable-ramp-delay = <500>;
|
||||
|
||||
/* hack until we rig up the gpu consumer */
|
||||
regulator-always-on;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&pm8998_gpio {
|
||||
vol_keys_default: vol-keys-default {
|
||||
pinconf {
|
||||
pins = "gpio5", "gpio6";
|
||||
function = "normal";
|
||||
bias-pull-up;
|
||||
input-enable;
|
||||
qcom,drive-strength = <PMIC_GPIO_STRENGTH_NO>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&qusb2phy {
|
||||
status = "okay";
|
||||
|
||||
vdda-pll-supply = <&vreg_l12a_1p8>;
|
||||
vdda-phy-dpdm-supply = <&vreg_l24a_3p075>;
|
||||
};
|
||||
|
||||
&rpm_requests {
|
||||
pm8998-regulators {
|
||||
compatible = "qcom,rpm-pm8998-regulators";
|
||||
|
||||
vdd_s1-supply = <&vph_pwr>;
|
||||
vdd_s2-supply = <&vph_pwr>;
|
||||
vdd_s3-supply = <&vph_pwr>;
|
||||
vdd_s4-supply = <&vph_pwr>;
|
||||
vdd_s5-supply = <&vph_pwr>;
|
||||
vdd_s6-supply = <&vph_pwr>;
|
||||
vdd_s7-supply = <&vph_pwr>;
|
||||
vdd_s8-supply = <&vph_pwr>;
|
||||
vdd_s9-supply = <&vph_pwr>;
|
||||
vdd_s10-supply = <&vph_pwr>;
|
||||
vdd_s11-supply = <&vph_pwr>;
|
||||
vdd_s12-supply = <&vph_pwr>;
|
||||
vdd_s13-supply = <&vph_pwr>;
|
||||
vdd_l1_l27-supply = <&vreg_s7a_1p025>;
|
||||
vdd_l2_l8_l17-supply = <&vreg_s3a_1p35>;
|
||||
vdd_l3_l11-supply = <&vreg_s7a_1p025>;
|
||||
vdd_l4_l5-supply = <&vreg_s7a_1p025>;
|
||||
vdd_l6-supply = <&vreg_s5a_2p04>;
|
||||
vdd_l7_l12_l14_l15-supply = <&vreg_s5a_2p04>;
|
||||
vdd_l9-supply = <&vreg_bob>;
|
||||
vdd_l10_l23_l25-supply = <&vreg_bob>;
|
||||
vdd_l13_l19_l21-supply = <&vreg_bob>;
|
||||
vdd_l16_l28-supply = <&vreg_bob>;
|
||||
vdd_l18_l22-supply = <&vreg_bob>;
|
||||
vdd_l20_l24-supply = <&vreg_bob>;
|
||||
vdd_l26-supply = <&vreg_s3a_1p35>;
|
||||
vdd_lvs1_lvs2-supply = <&vreg_s4a_1p8>;
|
||||
|
||||
vreg_s3a_1p35: s3 {
|
||||
regulator-min-microvolt = <1352000>;
|
||||
regulator-max-microvolt = <1352000>;
|
||||
};
|
||||
vreg_s4a_1p8: s4 {
|
||||
regulator-min-microvolt = <1800000>;
|
||||
regulator-max-microvolt = <1800000>;
|
||||
regulator-allow-set-load;
|
||||
};
|
||||
vreg_s5a_2p04: s5 {
|
||||
regulator-min-microvolt = <1904000>;
|
||||
regulator-max-microvolt = <2040000>;
|
||||
};
|
||||
vreg_s7a_1p025: s7 {
|
||||
regulator-min-microvolt = <900000>;
|
||||
regulator-max-microvolt = <1028000>;
|
||||
};
|
||||
vreg_l1a_0p875: l1 {
|
||||
regulator-min-microvolt = <880000>;
|
||||
regulator-max-microvolt = <880000>;
|
||||
};
|
||||
vreg_l2a_1p2: l2 {
|
||||
regulator-min-microvolt = <1200000>;
|
||||
regulator-max-microvolt = <1200000>;
|
||||
};
|
||||
vreg_l3a_1p0: l3 {
|
||||
regulator-min-microvolt = <1000000>;
|
||||
regulator-max-microvolt = <1000000>;
|
||||
};
|
||||
vreg_l5a_0p8: l5 {
|
||||
regulator-min-microvolt = <800000>;
|
||||
regulator-max-microvolt = <800000>;
|
||||
};
|
||||
vreg_l6a_1p8: l6 {
|
||||
regulator-min-microvolt = <1808000>;
|
||||
regulator-max-microvolt = <1808000>;
|
||||
};
|
||||
vreg_l7a_1p8: l7 {
|
||||
regulator-min-microvolt = <1800000>;
|
||||
regulator-max-microvolt = <1800000>;
|
||||
};
|
||||
vreg_l8a_1p2: l8 {
|
||||
regulator-min-microvolt = <1200000>;
|
||||
regulator-max-microvolt = <1200000>;
|
||||
};
|
||||
vreg_l9a_1p8: l9 {
|
||||
regulator-min-microvolt = <1808000>;
|
||||
regulator-max-microvolt = <2960000>;
|
||||
};
|
||||
vreg_l10a_1p8: l10 {
|
||||
regulator-min-microvolt = <1808000>;
|
||||
regulator-max-microvolt = <2960000>;
|
||||
};
|
||||
vreg_l11a_1p0: l11 {
|
||||
regulator-min-microvolt = <1000000>;
|
||||
regulator-max-microvolt = <1000000>;
|
||||
};
|
||||
vreg_l12a_1p8: l12 {
|
||||
regulator-min-microvolt = <1800000>;
|
||||
regulator-max-microvolt = <1800000>;
|
||||
};
|
||||
vreg_l13a_2p95: l13 {
|
||||
regulator-min-microvolt = <1808000>;
|
||||
regulator-max-microvolt = <2960000>;
|
||||
};
|
||||
vreg_l14a_1p88: l14 {
|
||||
regulator-min-microvolt = <1880000>;
|
||||
regulator-max-microvolt = <1880000>;
|
||||
};
|
||||
vreg_l15a_1p8: l15 {
|
||||
regulator-min-microvolt = <1800000>;
|
||||
regulator-max-microvolt = <1800000>;
|
||||
};
|
||||
vreg_l16a_2p7: l16 {
|
||||
regulator-min-microvolt = <2704000>;
|
||||
regulator-max-microvolt = <2704000>;
|
||||
};
|
||||
vreg_l17a_1p3: l17 {
|
||||
regulator-min-microvolt = <1304000>;
|
||||
regulator-max-microvolt = <1304000>;
|
||||
};
|
||||
vreg_l18a_2p7: l18 {
|
||||
regulator-min-microvolt = <2704000>;
|
||||
regulator-max-microvolt = <2704000>;
|
||||
};
|
||||
vreg_l19a_3p0: l19 {
|
||||
regulator-min-microvolt = <3008000>;
|
||||
regulator-max-microvolt = <3008000>;
|
||||
};
|
||||
vreg_l20a_2p95: l20 {
|
||||
regulator-min-microvolt = <2960000>;
|
||||
regulator-max-microvolt = <2960000>;
|
||||
regulator-allow-set-load;
|
||||
};
|
||||
vreg_l21a_2p95: l21 {
|
||||
regulator-min-microvolt = <2960000>;
|
||||
regulator-max-microvolt = <2960000>;
|
||||
regulator-allow-set-load;
|
||||
regulator-system-load = <800000>;
|
||||
};
|
||||
vreg_l22a_2p85: l22 {
|
||||
regulator-min-microvolt = <2864000>;
|
||||
regulator-max-microvolt = <2864000>;
|
||||
};
|
||||
vreg_l23a_3p3: l23 {
|
||||
regulator-min-microvolt = <3312000>;
|
||||
regulator-max-microvolt = <3312000>;
|
||||
};
|
||||
vreg_l24a_3p075: l24 {
|
||||
regulator-min-microvolt = <3088000>;
|
||||
regulator-max-microvolt = <3088000>;
|
||||
};
|
||||
vreg_l25a_3p3: l25 {
|
||||
regulator-min-microvolt = <3104000>;
|
||||
regulator-max-microvolt = <3312000>;
|
||||
};
|
||||
vreg_l26a_1p2: l26 {
|
||||
regulator-min-microvolt = <1200000>;
|
||||
regulator-max-microvolt = <1200000>;
|
||||
regulator-allow-set-load;
|
||||
};
|
||||
vreg_l28_3p0: l28 {
|
||||
regulator-min-microvolt = <3008000>;
|
||||
regulator-max-microvolt = <3008000>;
|
||||
};
|
||||
vreg_lvs1a_1p8: lvs1 { };
|
||||
vreg_lvs2a_1p8: lvs2 { };
|
||||
};
|
||||
|
||||
pmi8998-regulators {
|
||||
compatible = "qcom,rpm-pmi8998-regulators";
|
||||
|
||||
vdd_bob-supply = <&vph_pwr>;
|
||||
|
||||
vreg_bob: bob {
|
||||
regulator-min-microvolt = <3312000>;
|
||||
regulator-max-microvolt = <3600000>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&tlmm {
|
||||
gpio-reserved-ranges = <0 4>, <81 4>;
|
||||
|
||||
hall_sensor_default: hall-sensor-default {
|
||||
pins = "gpio124";
|
||||
function = "gpio";
|
||||
drive-strength = <2>;
|
||||
bias-disable;
|
||||
input-enable;
|
||||
};
|
||||
|
||||
ts_int_active: ts-int-active {
|
||||
pins = "gpio125";
|
||||
function = "gpio";
|
||||
drive-strength = <8>;
|
||||
bias-pull-up;
|
||||
};
|
||||
|
||||
ts_reset_active: ts-reset-active {
|
||||
pins = "gpio89";
|
||||
function = "gpio";
|
||||
drive-strength = <8>;
|
||||
bias-pull-up;
|
||||
};
|
||||
};
|
||||
|
||||
&ufshc {
|
||||
status = "okay";
|
||||
|
||||
vcc-supply = <&vreg_l20a_2p95>;
|
||||
vccq-supply = <&vreg_l26a_1p2>;
|
||||
vccq2-supply = <&vreg_s4a_1p8>;
|
||||
vcc-max-microamp = <750000>;
|
||||
vccq-max-microamp = <560000>;
|
||||
vccq2-max-microamp = <750000>;
|
||||
};
|
||||
|
||||
&ufsphy {
|
||||
status = "okay";
|
||||
|
||||
vdda-phy-supply = <&vreg_l1a_0p875>;
|
||||
vdda-pll-supply = <&vreg_l2a_1p2>;
|
||||
vddp-ref-clk-supply = <&vreg_l26a_1p2>;
|
||||
vdda-phy-max-microamp = <51400>;
|
||||
vdda-pll-max-microamp = <14600>;
|
||||
vddp-ref-clk-max-microamp = <100>;
|
||||
vddp-ref-clk-always-on;
|
||||
};
|
||||
|
||||
&usb3 {
|
||||
status = "okay";
|
||||
|
||||
/* Disable USB3 clock requirement as the device only supports USB2 */
|
||||
qcom,select-utmi-as-pipe-clk;
|
||||
};
|
||||
|
||||
&usb3_dwc3 {
|
||||
/* Drop the unused USB 3 PHY */
|
||||
phys = <&qusb2phy>;
|
||||
phy-names = "usb2-phy";
|
||||
|
||||
/* Fastest mode for USB 2 */
|
||||
maximum-speed = "high-speed";
|
||||
|
||||
/* Force to peripheral until we can switch modes */
|
||||
dr_mode = "peripheral";
|
||||
};
|
||||
|
||||
&wifi {
|
||||
/* Leave disabled until MSS is functional */
|
||||
vdd-0.8-cx-mx-supply = <&vreg_l5a_0p8>;
|
||||
vdd-1.8-xo-supply = <&vreg_l7a_1p8>;
|
||||
vdd-1.3-rfa-supply = <&vreg_l17a_1p3>;
|
||||
vdd-3.3-ch0-supply = <&vreg_l25a_3p3>;
|
||||
};
|
||||
|
|
@ -0,0 +1,25 @@
|
|||
// SPDX-License-Identifier: BSD-3-Clause
|
||||
/*
|
||||
* OnePlus 5T (dumpling) device tree
|
||||
*
|
||||
* Copyright (c) 2021, Jami Kettunen <jamipkettunen@gmail.com>
|
||||
*/
|
||||
|
||||
#include "msm8998-oneplus-common.dtsi"
|
||||
|
||||
/ {
|
||||
model = "OnePlus 5T";
|
||||
compatible = "oneplus,dumpling", "qcom,msm8998";
|
||||
/* Required for bootloader to select correct board */
|
||||
qcom,board-id = <8 0 17801 43>;
|
||||
};
|
||||
|
||||
/* Update the screen height values from 1920 to 2160 on the 5T */
|
||||
&framebuffer0 {
|
||||
height = <2160>;
|
||||
};
|
||||
|
||||
/* Adjust digitizer area height to match the 5T's taller panel */
|
||||
&rmi4_f12 {
|
||||
touchscreen-y-mm = <137>;
|
||||
};
|
||||
Loading…
Reference in New Issue