avr32: Add support for Mediama RMTx add-on board for ATNGW100
Signed-off-by: Peter Ma <pma@mediamatech.com> Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
This commit is contained in:
Peter Ma
Haavard Skinnemoen
parent
a89ab11454
commit
4024533e60
|
|
@ -21,6 +21,18 @@ config BOARD_ATNGW100_EVKLCD10X
|
|||
The MCI pins can be reenabled by editing the "add device function" but
|
||||
this may break the setup for other displays that use these pins.
|
||||
|
||||
config BOARD_ATNGW100_MRMT
|
||||
bool "Mediama RMT1/2 add-on board"
|
||||
help
|
||||
This enables support for the Mediama RMT1 or RMT2 board.
|
||||
RMT provides LCD support, AC97 codec and other
|
||||
optional peripherals to the Atmel NGW100.
|
||||
|
||||
This choice disables the detect pin and the write-protect pin for the
|
||||
MCI platform device, since it conflicts with the LCD platform device.
|
||||
The MCI pins can be reenabled by editing the "add device function" but
|
||||
this may break the setup for other displays that use these pins.
|
||||
|
||||
endchoice
|
||||
|
||||
choice
|
||||
|
|
@ -39,4 +51,8 @@ config BOARD_ATNGW100_EVKLCD10X_POW_QVGA
|
|||
|
||||
endchoice
|
||||
|
||||
if BOARD_ATNGW100_MRMT
|
||||
source "arch/avr32/boards/atngw100/Kconfig_mrmt"
|
||||
endif
|
||||
|
||||
endif # BOARD_ATNGW100
|
||||
|
|
|
|||
|
|
@ -0,0 +1,80 @@
|
|||
# RMT for NGW100 customization
|
||||
|
||||
choice
|
||||
prompt "RMT Version"
|
||||
help
|
||||
Select the RMTx board version.
|
||||
|
||||
config BOARD_MRMT_REV1
|
||||
bool "RMT1"
|
||||
config BOARD_MRMT_REV2
|
||||
bool "RMT2"
|
||||
|
||||
endchoice
|
||||
|
||||
config BOARD_MRMT_AC97
|
||||
bool "Enable AC97 CODEC"
|
||||
help
|
||||
Enable the UCB1400 AC97 CODEC driver.
|
||||
|
||||
choice
|
||||
prompt "Touchscreen Driver"
|
||||
default BOARD_MRMT_ADS7846_TS
|
||||
|
||||
config BOARD_MRMT_UCB1400_TS
|
||||
bool "Use UCB1400 Touchscreen"
|
||||
|
||||
config BOARD_MRMT_ADS7846_TS
|
||||
bool "Use ADS7846 Touchscreen"
|
||||
|
||||
endchoice
|
||||
|
||||
choice
|
||||
prompt "RMTx LCD Selection"
|
||||
default BOARD_MRMT_LCD_DISABLE
|
||||
|
||||
config BOARD_MRMT_LCD_DISABLE
|
||||
bool "LCD Disabled"
|
||||
|
||||
config BOARD_MRMT_LCD_LQ043T3DX0X
|
||||
bool "Sharp LQ043T3DX0x or compatible"
|
||||
help
|
||||
If using RMT2, be sure to load the resistor pack selectors accordingly
|
||||
|
||||
if BOARD_MRMT_REV2
|
||||
config BOARD_MRMT_LCD_KWH043GM08
|
||||
bool "Formike KWH043GM08 or compatible"
|
||||
help
|
||||
Be sure to load the RMT2 resistor pack selectors accordingly
|
||||
endif
|
||||
|
||||
endchoice
|
||||
|
||||
if !BOARD_MRMT_LCD_DISABLE
|
||||
config BOARD_MRMT_BL_PWM
|
||||
bool "Use PWM control for LCD Backlight"
|
||||
help
|
||||
Use PWM driver for controlling LCD Backlight.
|
||||
Otherwise, LCD Backlight is always on.
|
||||
endif
|
||||
|
||||
config BOARD_MRMT_RTC_I2C
|
||||
bool "Use External RTC on I2C Bus"
|
||||
help
|
||||
RMT1 has an optional RTC device on the I2C bus.
|
||||
It is a SII S35390A. Be sure to select the
|
||||
matching RTC driver.
|
||||
|
||||
choice
|
||||
prompt "Wireless Module on ttyS2"
|
||||
default BOARD_MRMT_WIRELESS_ZB
|
||||
|
||||
config BOARD_MRMT_WIRELESS_ZB
|
||||
bool "Use ZigBee/802.15.4 Module"
|
||||
|
||||
config BOARD_MRMT_WIRELESS_BT
|
||||
bool "Use Bluetooth (HCI) Module"
|
||||
|
||||
config BOARD_MRMT_WIRELESS_NONE
|
||||
bool "Not Installed"
|
||||
endchoice
|
||||
|
|
@ -1,2 +1,3 @@
|
|||
obj-y += setup.o flash.o
|
||||
obj-$(CONFIG_BOARD_ATNGW100_EVKLCD10X) += evklcd10x.o
|
||||
obj-$(CONFIG_BOARD_ATNGW100_MRMT) += mrmt.o
|
||||
|
|
|
|||
|
|
@ -0,0 +1,373 @@
|
|||
/*
|
||||
* Board-specific setup code for Remote Media Terminal 1 (RMT1)
|
||||
* add-on board for the ATNGW100 Network Gateway
|
||||
*
|
||||
* Copyright (C) 2008 Mediama Technologies
|
||||
* Based on ATNGW100 Network Gateway (Copyright (C) Atmel)
|
||||
*
|
||||
* This program is free software; you can redistribute it and/or modify
|
||||
* it under the terms of the GNU General Public License version 2 as
|
||||
* published by the Free Software Foundation.
|
||||
*/
|
||||
#include <linux/gpio.h>
|
||||
#include <linux/init.h>
|
||||
#include <linux/irq.h>
|
||||
#include <linux/linkage.h>
|
||||
#include <linux/platform_device.h>
|
||||
#include <linux/types.h>
|
||||
#include <linux/fb.h>
|
||||
#include <linux/leds.h>
|
||||
#include <linux/input.h>
|
||||
#include <linux/gpio_keys.h>
|
||||
#include <linux/atmel_serial.h>
|
||||
#include <linux/spi/spi.h>
|
||||
#include <linux/spi/ads7846.h>
|
||||
|
||||
#include <video/atmel_lcdc.h>
|
||||
#include <sound/atmel-ac97c.h>
|
||||
|
||||
#include <asm/delay.h>
|
||||
#include <asm/io.h>
|
||||
#include <asm/setup.h>
|
||||
|
||||
#include <mach/at32ap700x.h>
|
||||
#include <mach/board.h>
|
||||
#include <mach/init.h>
|
||||
#include <mach/portmux.h>
|
||||
|
||||
/* Define board-specifoic GPIO assignments */
|
||||
#define PIN_LCD_BL GPIO_PIN_PA(28)
|
||||
#define PWM_CH_BL 0 /* Must match with GPIO pin definition */
|
||||
#define PIN_LCD_DISP GPIO_PIN_PA(31)
|
||||
#define PIN_AC97_RST_N GPIO_PIN_PA(30)
|
||||
#define PB_EXTINT_BASE 25
|
||||
#define TS_IRQ 0
|
||||
#define PIN_TS_EXTINT GPIO_PIN_PB(PB_EXTINT_BASE+TS_IRQ)
|
||||
#define PIN_PB_LEFT GPIO_PIN_PB(11)
|
||||
#define PIN_PB_RIGHT GPIO_PIN_PB(12)
|
||||
#define PIN_PWR_SW_N GPIO_PIN_PB(14)
|
||||
#define PIN_PWR_ON GPIO_PIN_PB(13)
|
||||
#define PIN_ZB_RST_N GPIO_PIN_PA(21)
|
||||
#define PIN_BT_RST GPIO_PIN_PA(22)
|
||||
#define PIN_LED_SYS GPIO_PIN_PA(16)
|
||||
#define PIN_LED_A GPIO_PIN_PA(19)
|
||||
#define PIN_LED_B GPIO_PIN_PE(19)
|
||||
|
||||
#ifdef CONFIG_BOARD_MRMT_LCD_LQ043T3DX0X
|
||||
/* Sharp LQ043T3DX0x (or compatible) panel */
|
||||
static struct fb_videomode __initdata lcd_fb_modes[] = {
|
||||
{
|
||||
.name = "480x272 @ 59.94Hz",
|
||||
.refresh = 59.94,
|
||||
.xres = 480, .yres = 272,
|
||||
.pixclock = KHZ2PICOS(9000),
|
||||
|
||||
.left_margin = 2, .right_margin = 2,
|
||||
.upper_margin = 3, .lower_margin = 9,
|
||||
.hsync_len = 41, .vsync_len = 1,
|
||||
|
||||
.sync = 0,
|
||||
.vmode = FB_VMODE_NONINTERLACED,
|
||||
},
|
||||
};
|
||||
|
||||
static struct fb_monspecs __initdata lcd_fb_default_monspecs = {
|
||||
.manufacturer = "SHA",
|
||||
.monitor = "LQ043T3DX02",
|
||||
.modedb = lcd_fb_modes,
|
||||
.modedb_len = ARRAY_SIZE(lcd_fb_modes),
|
||||
.hfmin = 14915,
|
||||
.hfmax = 17638,
|
||||
.vfmin = 53,
|
||||
.vfmax = 61,
|
||||
.dclkmax = 9260000,
|
||||
};
|
||||
|
||||
static struct atmel_lcdfb_info __initdata rmt_lcdc_data = {
|
||||
.default_bpp = 24,
|
||||
.default_dmacon = ATMEL_LCDC_DMAEN | ATMEL_LCDC_DMA2DEN,
|
||||
.default_lcdcon2 = (ATMEL_LCDC_DISTYPE_TFT
|
||||
| ATMEL_LCDC_CLKMOD_ALWAYSACTIVE
|
||||
| ATMEL_LCDC_INVCLK_NORMAL
|
||||
| ATMEL_LCDC_MEMOR_BIG),
|
||||
.lcd_wiring_mode = ATMEL_LCDC_WIRING_RGB,
|
||||
.default_monspecs = &lcd_fb_default_monspecs,
|
||||
.guard_time = 2,
|
||||
};
|
||||
#endif
|
||||
|
||||
#ifdef CONFIG_BOARD_MRMT_LCD_KWH043GM08
|
||||
/* Sharp KWH043GM08-Fxx (or compatible) panel */
|
||||
static struct fb_videomode __initdata lcd_fb_modes[] = {
|
||||
{
|
||||
.name = "480x272 @ 59.94Hz",
|
||||
.refresh = 59.94,
|
||||
.xres = 480, .yres = 272,
|
||||
.pixclock = KHZ2PICOS(9000),
|
||||
|
||||
.left_margin = 2, .right_margin = 2,
|
||||
.upper_margin = 3, .lower_margin = 9,
|
||||
.hsync_len = 41, .vsync_len = 1,
|
||||
|
||||
.sync = 0,
|
||||
.vmode = FB_VMODE_NONINTERLACED,
|
||||
},
|
||||
};
|
||||
|
||||
static struct fb_monspecs __initdata lcd_fb_default_monspecs = {
|
||||
.manufacturer = "FOR",
|
||||
.monitor = "KWH043GM08",
|
||||
.modedb = lcd_fb_modes,
|
||||
.modedb_len = ARRAY_SIZE(lcd_fb_modes),
|
||||
.hfmin = 14915,
|
||||
.hfmax = 17638,
|
||||
.vfmin = 53,
|
||||
.vfmax = 61,
|
||||
.dclkmax = 9260000,
|
||||
};
|
||||
|
||||
static struct atmel_lcdfb_info __initdata rmt_lcdc_data = {
|
||||
.default_bpp = 24,
|
||||
.default_dmacon = ATMEL_LCDC_DMAEN | ATMEL_LCDC_DMA2DEN,
|
||||
.default_lcdcon2 = (ATMEL_LCDC_DISTYPE_TFT
|
||||
| ATMEL_LCDC_CLKMOD_ALWAYSACTIVE
|
||||
| ATMEL_LCDC_INVCLK_INVERTED
|
||||
| ATMEL_LCDC_MEMOR_BIG),
|
||||
.lcd_wiring_mode = ATMEL_LCDC_WIRING_RGB,
|
||||
.default_monspecs = &lcd_fb_default_monspecs,
|
||||
.guard_time = 2,
|
||||
};
|
||||
#endif
|
||||
|
||||
#ifdef CONFIG_BOARD_MRMT_AC97
|
||||
static struct ac97c_platform_data __initdata ac97c0_data = {
|
||||
.reset_pin = PIN_AC97_RST_N,
|
||||
};
|
||||
#endif
|
||||
|
||||
#ifdef CONFIG_BOARD_MRMT_UCB1400_TS
|
||||
/* NOTE: IRQ assignment relies on kernel module parameter */
|
||||
static struct platform_device rmt_ts_device = {
|
||||
.name = "ucb1400_ts",
|
||||
.id = -1,
|
||||
}
|
||||
};
|
||||
#endif
|
||||
|
||||
#ifdef CONFIG_BOARD_MRMT_BL_PWM
|
||||
/* PWM LEDs: LCD Backlight, etc */
|
||||
static struct gpio_led rmt_pwm_led[] = {
|
||||
/* here the "gpio" is actually a PWM channel */
|
||||
{ .name = "backlight", .gpio = PWM_CH_BL, },
|
||||
};
|
||||
|
||||
static struct gpio_led_platform_data rmt_pwm_led_data = {
|
||||
.num_leds = ARRAY_SIZE(rmt_pwm_led),
|
||||
.leds = rmt_pwm_led,
|
||||
};
|
||||
|
||||
static struct platform_device rmt_pwm_led_dev = {
|
||||
.name = "leds-atmel-pwm",
|
||||
.id = -1,
|
||||
.dev = {
|
||||
.platform_data = &rmt_pwm_led_data,
|
||||
},
|
||||
};
|
||||
#endif
|
||||
|
||||
#ifdef CONFIG_BOARD_MRMT_ADS7846_TS
|
||||
static int ads7846_pendown_state(void)
|
||||
{
|
||||
return !gpio_get_value( PIN_TS_EXTINT ); /* PENIRQ.*/
|
||||
}
|
||||
|
||||
static struct ads7846_platform_data ads_info = {
|
||||
.model = 7846,
|
||||
.keep_vref_on = 0, /* Use external VREF pin */
|
||||
.vref_delay_usecs = 0,
|
||||
.vref_mv = 3300, /* VREF = 3.3V */
|
||||
.settle_delay_usecs = 800,
|
||||
.penirq_recheck_delay_usecs = 800,
|
||||
.x_plate_ohms = 750,
|
||||
.y_plate_ohms = 300,
|
||||
.pressure_max = 4096,
|
||||
.debounce_max = 1,
|
||||
.debounce_rep = 0,
|
||||
.debounce_tol = (~0),
|
||||
.get_pendown_state = ads7846_pendown_state,
|
||||
.filter = NULL,
|
||||
.filter_init = NULL,
|
||||
};
|
||||
|
||||
static struct spi_board_info spi01_board_info[] __initdata = {
|
||||
{
|
||||
.modalias = "ads7846",
|
||||
.max_speed_hz = 31250*26,
|
||||
.bus_num = 0,
|
||||
.chip_select = 1,
|
||||
.platform_data = &ads_info,
|
||||
.irq = AT32_EXTINT(TS_IRQ),
|
||||
},
|
||||
};
|
||||
#endif
|
||||
|
||||
/* GPIO Keys: left, right, power, etc */
|
||||
static const struct gpio_keys_button rmt_gpio_keys_buttons[] = {
|
||||
[0] = {
|
||||
.type = EV_KEY,
|
||||
.code = KEY_POWER,
|
||||
.gpio = PIN_PWR_SW_N,
|
||||
.active_low = 1,
|
||||
.desc = "power button",
|
||||
},
|
||||
[1] = {
|
||||
.type = EV_KEY,
|
||||
.code = KEY_LEFT,
|
||||
.gpio = PIN_PB_LEFT,
|
||||
.active_low = 1,
|
||||
.desc = "left button",
|
||||
},
|
||||
[2] = {
|
||||
.type = EV_KEY,
|
||||
.code = KEY_RIGHT,
|
||||
.gpio = PIN_PB_RIGHT,
|
||||
.active_low = 1,
|
||||
.desc = "right button",
|
||||
},
|
||||
};
|
||||
|
||||
static const struct gpio_keys_platform_data rmt_gpio_keys_data = {
|
||||
.nbuttons = ARRAY_SIZE(rmt_gpio_keys_buttons),
|
||||
.buttons = (void *) rmt_gpio_keys_buttons,
|
||||
};
|
||||
|
||||
static struct platform_device rmt_gpio_keys = {
|
||||
.name = "gpio-keys",
|
||||
.id = -1,
|
||||
.dev = {
|
||||
.platform_data = (void *) &rmt_gpio_keys_data,
|
||||
}
|
||||
};
|
||||
|
||||
#ifdef CONFIG_BOARD_MRMT_RTC_I2C
|
||||
static struct i2c_board_info __initdata mrmt1_i2c_rtc = {
|
||||
I2C_BOARD_INFO("s35390a", 0x30),
|
||||
.irq = 0,
|
||||
};
|
||||
#endif
|
||||
|
||||
static void mrmt_power_off(void)
|
||||
{
|
||||
/* PWR_ON=0 will force power off */
|
||||
gpio_set_value( PIN_PWR_ON, 0 );
|
||||
}
|
||||
|
||||
static int __init mrmt1_init(void)
|
||||
{
|
||||
gpio_set_value( PIN_PWR_ON, 1 ); /* Ensure PWR_ON is enabled */
|
||||
|
||||
pm_power_off = mrmt_power_off;
|
||||
|
||||
/* Setup USARTS (other than console) */
|
||||
at32_map_usart(2, 1, 0); /* USART 2: /dev/ttyS1, RMT1:DB9M */
|
||||
at32_map_usart(3, 2, ATMEL_USART_RTS | ATMEL_USART_CTS);
|
||||
/* USART 3: /dev/ttyS2, RMT1:Wireless, w/ RTS/CTS */
|
||||
at32_add_device_usart(1);
|
||||
at32_add_device_usart(2);
|
||||
|
||||
/* Select GPIO Key pins */
|
||||
at32_select_gpio( PIN_PWR_SW_N, AT32_GPIOF_DEGLITCH);
|
||||
at32_select_gpio( PIN_PB_LEFT, AT32_GPIOF_DEGLITCH);
|
||||
at32_select_gpio( PIN_PB_RIGHT, AT32_GPIOF_DEGLITCH);
|
||||
platform_device_register(&rmt_gpio_keys);
|
||||
|
||||
#ifdef CONFIG_BOARD_MRMT_RTC_I2C
|
||||
i2c_register_board_info(0, &mrmt1_i2c_rtc, 1);
|
||||
#endif
|
||||
|
||||
#ifndef CONFIG_BOARD_MRMT_LCD_DISABLE
|
||||
/* User "alternate" LCDC inferface on Port E & D */
|
||||
/* NB: exclude LCDC_CC pin, as NGW100 reserves it for other use */
|
||||
at32_add_device_lcdc(0, &rmt_lcdc_data,
|
||||
fbmem_start, fbmem_size,
|
||||
(ATMEL_LCDC_ALT_24BIT | ATMEL_LCDC_PE_DVAL ) );
|
||||
#endif
|
||||
|
||||
#ifdef CONFIG_BOARD_MRMT_AC97
|
||||
at32_add_device_ac97c(0, &ac97c0_data, AC97C_BOTH);
|
||||
#endif
|
||||
|
||||
#ifdef CONFIG_BOARD_MRMT_ADS7846_TS
|
||||
/* Select the Touchscreen interrupt pin mode */
|
||||
at32_select_periph( GPIO_PIOB_BASE, 1 << (PB_EXTINT_BASE+TS_IRQ),
|
||||
GPIO_PERIPH_A, AT32_GPIOF_DEGLITCH);
|
||||
set_irq_type( AT32_EXTINT(TS_IRQ), IRQ_TYPE_EDGE_FALLING );
|
||||
spi_register_board_info(spi01_board_info,ARRAY_SIZE(spi01_board_info));
|
||||
#endif
|
||||
|
||||
#ifdef CONFIG_BOARD_MRMT_UCB1400_TS
|
||||
/* Select the Touchscreen interrupt pin mode */
|
||||
at32_select_periph( GPIO_PIOB_BASE, 1 << (PB_EXTINT_BASE+TS_IRQ),
|
||||
GPIO_PERIPH_A, AT32_GPIOF_DEGLITCH);
|
||||
platform_device_register(&rmt_ts_device);
|
||||
#endif
|
||||
|
||||
at32_select_gpio( PIN_LCD_DISP, AT32_GPIOF_OUTPUT );
|
||||
gpio_request( PIN_LCD_DISP, "LCD_DISP" );
|
||||
gpio_direction_output( PIN_LCD_DISP, 0 ); /* LCD DISP */
|
||||
#ifdef CONFIG_BOARD_MRMT_LCD_DISABLE
|
||||
/* Keep Backlight and DISP off */
|
||||
at32_select_gpio( PIN_LCD_BL, AT32_GPIOF_OUTPUT );
|
||||
gpio_request( PIN_LCD_BL, "LCD_BL" );
|
||||
gpio_direction_output( PIN_LCD_BL, 0 ); /* Backlight */
|
||||
#else
|
||||
gpio_set_value( PIN_LCD_DISP, 1 ); /* DISP asserted first */
|
||||
#ifdef CONFIG_BOARD_MRMT_BL_PWM
|
||||
/* Use PWM for Backlight controls */
|
||||
at32_add_device_pwm(1 << PWM_CH_BL);
|
||||
platform_device_register(&rmt_pwm_led_dev);
|
||||
#else
|
||||
/* Backlight always on */
|
||||
udelay( 1 );
|
||||
at32_select_gpio( PIN_LCD_BL, AT32_GPIOF_OUTPUT );
|
||||
gpio_request( PIN_LCD_BL, "LCD_BL" );
|
||||
gpio_direction_output( PIN_LCD_BL, 1 );
|
||||
#endif
|
||||
#endif
|
||||
|
||||
/* Make sure BT and Zigbee modules in reset */
|
||||
at32_select_gpio( PIN_BT_RST, AT32_GPIOF_OUTPUT );
|
||||
gpio_request( PIN_BT_RST, "BT_RST" );
|
||||
gpio_direction_output( PIN_BT_RST, 1 );
|
||||
/* BT Module in Reset */
|
||||
|
||||
at32_select_gpio( PIN_ZB_RST_N, AT32_GPIOF_OUTPUT );
|
||||
gpio_request( PIN_ZB_RST_N, "ZB_RST_N" );
|
||||
gpio_direction_output( PIN_ZB_RST_N, 0 );
|
||||
/* XBee Module in Reset */
|
||||
|
||||
#ifdef CONFIG_BOARD_MRMT_WIRELESS_ZB
|
||||
udelay( 1000 );
|
||||
/* Unreset the XBee Module */
|
||||
gpio_set_value( PIN_ZB_RST_N, 1 );
|
||||
#endif
|
||||
#ifdef CONFIG_BOARD_MRMT_WIRELESS_BT
|
||||
udelay( 1000 );
|
||||
/* Unreset the BT Module */
|
||||
gpio_set_value( PIN_BT_RST, 0 );
|
||||
#endif
|
||||
|
||||
return 0;
|
||||
}
|
||||
arch_initcall(mrmt1_init);
|
||||
|
||||
static int __init mrmt1_early_init(void)
|
||||
{
|
||||
/* To maintain power-on signal in case boot loader did not already */
|
||||
at32_select_gpio( PIN_PWR_ON, AT32_GPIOF_OUTPUT );
|
||||
gpio_request( PIN_PWR_ON, "PIN_PWR_ON" );
|
||||
gpio_direction_output( PIN_PWR_ON, 1 );
|
||||
|
||||
return 0;
|
||||
}
|
||||
core_initcall(mrmt1_early_init);
|
||||
|
|
@ -56,8 +56,13 @@ static struct spi_board_info spi0_board_info[] __initdata = {
|
|||
static struct mci_platform_data __initdata mci0_data = {
|
||||
.slot[0] = {
|
||||
.bus_width = 4,
|
||||
#if defined(CONFIG_BOARD_ATNGW100_EVKLCD10X) || defined(CONFIG_BOARD_ATNGW100_MRMT1)
|
||||
.detect_pin = GPIO_PIN_NONE,
|
||||
.wp_pin = GPIO_PIN_NONE,
|
||||
#else
|
||||
.detect_pin = GPIO_PIN_PC(25),
|
||||
.wp_pin = GPIO_PIN_PE(0),
|
||||
#endif
|
||||
},
|
||||
};
|
||||
|
||||
|
|
|
|||
File diff suppressed because it is too large
Load Diff
Loading…
Reference in New Issue