MIPS: OCTEON: program rx/tx-delay always from DT

Program rx/tx-delay always from DT.

Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: linux-mips@vger.kernel.org

arch/mips/boot/dts/cavium-octeon/octeon_3xxx.dts

@@ -180,6 +180,8 @@
 				ethernet@0 {
 					phy-handle = <&phy2>;
 					cavium,alt-phy-handle = <&phy100>;
+					rx-delay = <0>;
+					tx-delay = <0>;
 					fixed-link {
 						speed = <1000>;
 						full-duplex;
@@ -188,6 +190,8 @@
 				ethernet@1 {
 					phy-handle = <&phy3>;
 					cavium,alt-phy-handle = <&phy101>;
+					rx-delay = <0>;
+					tx-delay = <0>;
 					fixed-link {
 						speed = <1000>;
 						full-duplex;
@@ -196,6 +200,8 @@
 				ethernet@2 {
 					phy-handle = <&phy4>;
 					cavium,alt-phy-handle = <&phy102>;
+					rx-delay = <0>;
+					tx-delay = <0>;
 				};
 				ethernet@3 {
 					compatible = "cavium,octeon-3860-pip-port";

arch/mips/boot/dts/cavium-octeon/ubnt_e100.dts

@@ -33,12 +33,18 @@
 			interface@0 {
 				ethernet@0 {
 					phy-handle = <&phy7>;
+					rx-delay = <0>;
+					tx-delay = <0x10>;
 				};
 				ethernet@1 {
 					phy-handle = <&phy6>;
+					rx-delay = <0>;
+					tx-delay = <0x10>;
 				};
 				ethernet@2 {
 					phy-handle = <&phy5>;
+					rx-delay = <0>;
+					tx-delay = <0x10>;
 				};
 			};
 		};

arch/mips/cavium-octeon/executive/cvmx-helper-board.c

@@ -320,45 +320,6 @@ int __cvmx_helper_board_interface_probe(int interface, int supported_ports)
 	return supported_ports;
 }
 
-/**
- * Enable packet input/output from the hardware. This function is
- * called after by cvmx_helper_packet_hardware_enable() to
- * perform board specific initialization. For most boards
- * nothing is needed.
- *
- * @interface: Interface to enable
- *
- * Returns Zero on success, negative on failure
- */
-int __cvmx_helper_board_hardware_enable(int interface)
-{
-	if (cvmx_sysinfo_get()->board_type == CVMX_BOARD_TYPE_CN3005_EVB_HS5) {
-		if (interface == 0) {
-			/* Different config for switch port */
-			cvmx_write_csr(CVMX_ASXX_TX_CLK_SETX(1, interface), 0);
-			cvmx_write_csr(CVMX_ASXX_RX_CLK_SETX(1, interface), 0);
-			/*
-			 * Boards with gigabit WAN ports need a
-			 * different setting that is compatible with
-			 * 100 Mbit settings
-			 */
-			cvmx_write_csr(CVMX_ASXX_TX_CLK_SETX(0, interface),
-				       0xc);
-			cvmx_write_csr(CVMX_ASXX_RX_CLK_SETX(0, interface),
-				       0xc);
-		}
-	} else if (cvmx_sysinfo_get()->board_type ==
-			CVMX_BOARD_TYPE_UBNT_E100) {
-		cvmx_write_csr(CVMX_ASXX_RX_CLK_SETX(0, interface), 0);
-		cvmx_write_csr(CVMX_ASXX_TX_CLK_SETX(0, interface), 0x10);
-		cvmx_write_csr(CVMX_ASXX_RX_CLK_SETX(1, interface), 0);
-		cvmx_write_csr(CVMX_ASXX_TX_CLK_SETX(1, interface), 0x10);
-		cvmx_write_csr(CVMX_ASXX_RX_CLK_SETX(2, interface), 0);
-		cvmx_write_csr(CVMX_ASXX_TX_CLK_SETX(2, interface), 0x10);
-	}
-	return 0;
-}
-
 /**
  * Get the clock type used for the USB block based on board type.
  * Used by the USB code for auto configuration of clock type.

arch/mips/cavium-octeon/executive/cvmx-helper.c

@@ -762,7 +762,6 @@ static int __cvmx_helper_packet_hardware_enable(int interface)
 		result = __cvmx_helper_loop_enable(interface);
 		break;
 	}
-	result |= __cvmx_helper_board_hardware_enable(interface);
 	return result;
 }
 

arch/mips/cavium-octeon/octeon-platform.c

@@ -603,6 +603,45 @@ static void __init octeon_fdt_rm_ethernet(int node)
 	fdt_nop_node(initial_boot_params, node);
 }
 
+static void __init _octeon_rx_tx_delay(int eth, int rx_delay, int tx_delay)
+{
+	fdt_setprop_inplace_cell(initial_boot_params, eth, "rx-delay",
+				 rx_delay);
+	fdt_setprop_inplace_cell(initial_boot_params, eth, "tx-delay",
+				 tx_delay);
+}
+
+static void __init octeon_rx_tx_delay(int eth, int iface, int port)
+{
+	switch (cvmx_sysinfo_get()->board_type) {
+	case CVMX_BOARD_TYPE_CN3005_EVB_HS5:
+		if (iface == 0) {
+			if (port == 0) {
+				/*
+				 * Boards with gigabit WAN ports need a
+				 * different setting that is compatible with
+				 * 100 Mbit settings
+				 */
+				_octeon_rx_tx_delay(eth, 0xc, 0x0c);
+				return;
+			} else if (port == 1) {
+				/* Different config for switch port. */
+				_octeon_rx_tx_delay(eth, 0x0, 0x0);
+				return;
+			}
+		}
+		break;
+	case CVMX_BOARD_TYPE_UBNT_E100:
+		if (iface == 0 && port <= 2) {
+			_octeon_rx_tx_delay(eth, 0x0, 0x10);
+			return;
+		}
+		break;
+	}
+	fdt_nop_property(initial_boot_params, eth, "rx-delay");
+	fdt_nop_property(initial_boot_params, eth, "tx-delay");
+}
+
 static void __init octeon_fdt_pip_port(int iface, int i, int p, int max)
 {
 	char name_buffer[20];
@@ -633,6 +672,7 @@ static void __init octeon_fdt_pip_port(int iface, int i, int p, int max)
 		WARN_ON(octeon_has_fixed_link(ipd_port));
 	else if (!octeon_has_fixed_link(ipd_port))
 		fdt_nop_node(initial_boot_params, fixed_link);
+	octeon_rx_tx_delay(eth, i, p);
 }
 
 static void __init octeon_fdt_pip_iface(int pip, int idx)

arch/mips/include/asm/octeon/cvmx-helper-board.h

@@ -119,18 +119,6 @@ extern cvmx_helper_link_info_t __cvmx_helper_board_link_get(int ipd_port);
 extern int __cvmx_helper_board_interface_probe(int interface,
 					       int supported_ports);
 
-/**
- * Enable packet input/output from the hardware. This function is
- * called after by cvmx_helper_packet_hardware_enable() to
- * perform board specific initialization. For most boards
- * nothing is needed.
- *
- * @interface: Interface to enable
- *
- * Returns Zero on success, negative on failure
- */
-extern int __cvmx_helper_board_hardware_enable(int interface);
-
 enum cvmx_helper_board_usb_clock_types __cvmx_helper_board_usb_get_clock_type(void);
 
 #endif /* __CVMX_HELPER_BOARD_H__ */