tty: max310x: Fix invalid baudrate divisors calculator
Current calculator doesn't do it' job quite correct. First of all the max310x baud-rates generator supports the divisor being less than 16. In this case the x2/x4 modes can be used to double or quadruple the reference frequency. But the current baud-rate setter function just filters all these modes out by the first condition and setups these modes only if there is a clocks-baud division remainder. The former doesn't seem right at all, since enabling the x2/x4 modes causes the line noise tolerance reduction and should be only used as a last resort to enable a requested too high baud-rate. Finally the fraction is supposed to be calculated from D = Fref/(c*baud) formulae, but not from D % 16, which causes the precision loss. So to speak the current baud-rate calculator code works well only if the baud perfectly fits to the uart reference input frequency. Lets fix the calculator by implementing the algo fully compliant with the fractional baud-rate generator described in the datasheet: D = Fref / (c*baud), where c={16,8,4} is the x1/x2/x4 rate mode respectively, Fref - reference input frequency. The divisor fraction is calculated from the same formulae, but making sure it is found with a resolution of 0.0625 (four bits). Signed-off-by: Serge Semin <fancer.lancer@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This commit is contained in:
parent
b7382c73b2
commit
35240ba26a
|
@ -501,37 +501,48 @@ static bool max310x_reg_precious(struct device *dev, unsigned int reg)
|
||||||
|
|
||||||
static int max310x_set_baud(struct uart_port *port, int baud)
|
static int max310x_set_baud(struct uart_port *port, int baud)
|
||||||
{
|
{
|
||||||
unsigned int mode = 0, clk = port->uartclk, div = clk / baud;
|
unsigned int mode = 0, div = 0, frac = 0, c = 0, F = 0;
|
||||||
|
|
||||||
/* Check for minimal value for divider */
|
/*
|
||||||
if (div < 16)
|
* Calculate the integer divisor first. Select a proper mode
|
||||||
div = 16;
|
* in case if the requested baud is too high for the pre-defined
|
||||||
|
* clocks frequency.
|
||||||
if (clk % baud && (div / 16) < 0x8000) {
|
*/
|
||||||
/* Mode x2 */
|
div = port->uartclk / baud;
|
||||||
mode = MAX310X_BRGCFG_2XMODE_BIT;
|
if (div < 8) {
|
||||||
clk = port->uartclk * 2;
|
|
||||||
div = clk / baud;
|
|
||||||
|
|
||||||
if (clk % baud && (div / 16) < 0x8000) {
|
|
||||||
/* Mode x4 */
|
/* Mode x4 */
|
||||||
|
c = 4;
|
||||||
mode = MAX310X_BRGCFG_4XMODE_BIT;
|
mode = MAX310X_BRGCFG_4XMODE_BIT;
|
||||||
clk = port->uartclk * 4;
|
} else if (div < 16) {
|
||||||
div = clk / baud;
|
/* Mode x2 */
|
||||||
}
|
c = 8;
|
||||||
|
mode = MAX310X_BRGCFG_2XMODE_BIT;
|
||||||
|
} else {
|
||||||
|
c = 16;
|
||||||
}
|
}
|
||||||
|
|
||||||
max310x_port_write(port, MAX310X_BRGDIVMSB_REG, (div / 16) >> 8);
|
/* Calculate the divisor in accordance with the fraction coefficient */
|
||||||
max310x_port_write(port, MAX310X_BRGDIVLSB_REG, div / 16);
|
div /= c;
|
||||||
max310x_port_write(port, MAX310X_BRGCFG_REG, (div % 16) | mode);
|
F = c*baud;
|
||||||
|
|
||||||
return DIV_ROUND_CLOSEST(clk, div);
|
/* Calculate the baud rate fraction */
|
||||||
|
if (div > 0)
|
||||||
|
frac = (16*(port->uartclk % F)) / F;
|
||||||
|
else
|
||||||
|
div = 1;
|
||||||
|
|
||||||
|
max310x_port_write(port, MAX310X_BRGDIVMSB_REG, div >> 8);
|
||||||
|
max310x_port_write(port, MAX310X_BRGDIVLSB_REG, div);
|
||||||
|
max310x_port_write(port, MAX310X_BRGCFG_REG, frac | mode);
|
||||||
|
|
||||||
|
/* Return the actual baud rate we just programmed */
|
||||||
|
return (16*port->uartclk) / (c*(16*div + frac));
|
||||||
}
|
}
|
||||||
|
|
||||||
static int max310x_update_best_err(unsigned long f, long *besterr)
|
static int max310x_update_best_err(unsigned long f, long *besterr)
|
||||||
{
|
{
|
||||||
/* Use baudrate 115200 for calculate error */
|
/* Use baudrate 115200 for calculate error */
|
||||||
long err = f % (115200 * 16);
|
long err = f % (460800 * 16);
|
||||||
|
|
||||||
if ((*besterr < 0) || (*besterr > err)) {
|
if ((*besterr < 0) || (*besterr > err)) {
|
||||||
*besterr = err;
|
*besterr = err;
|
||||||
|
|
Loading…
Reference in New Issue