ARM: dts: add Plymovent BAS board
Plymovent BAS is a base system controller produced for the Plymovent filter systems. Co-Developed-by: David Jander <david@protonic.nl> Signed-off-by: David Jander <david@protonic.nl> Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This commit is contained in:
Oleksij Rempel
Shawn Guo
parent
8c906de4b7
commit
2c62f908c0
|
|
@ -465,6 +465,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \
|
|||
imx6dl-pico-hobbit.dtb \
|
||||
imx6dl-pico-nymph.dtb \
|
||||
imx6dl-pico-pi.dtb \
|
||||
imx6dl-plybas.dtb \
|
||||
imx6dl-plym2m.dtb \
|
||||
imx6dl-prtrvt.dtb \
|
||||
imx6dl-prtvt7.dtb \
|
||||
|
|
|
|||
|
|
@ -0,0 +1,394 @@
|
|||
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
||||
/*
|
||||
* Copyright (c) 2014 Protonic Holland
|
||||
* Copyright (c) 2020 Oleksij Rempel <kernel@pengutronix.de>, Pengutronix
|
||||
*/
|
||||
|
||||
/dts-v1/;
|
||||
#include <dt-bindings/gpio/gpio.h>
|
||||
#include <dt-bindings/leds/common.h>
|
||||
#include "imx6dl.dtsi"
|
||||
|
||||
/ {
|
||||
model = "Plymovent BAS board";
|
||||
compatible = "ply,plybas", "fsl,imx6dl";
|
||||
|
||||
chosen {
|
||||
stdout-path = &uart4;
|
||||
};
|
||||
|
||||
gpio_keys {
|
||||
compatible = "gpio-keys";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
autorepeat;
|
||||
|
||||
button@20 {
|
||||
label = "START";
|
||||
linux,code = <31>;
|
||||
gpios = <&gpio5 8 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
button@21 {
|
||||
label = "CLEAN";
|
||||
linux,code = <46>;
|
||||
gpios = <&gpio5 9 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
};
|
||||
|
||||
leds {
|
||||
compatible = "gpio-leds";
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&pinctrl_leds>;
|
||||
|
||||
led-0 {
|
||||
label = "debug0";
|
||||
gpios = <&gpio1 8 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
|
||||
led-1 {
|
||||
label = "debug1";
|
||||
gpios = <&gpio1 9 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
|
||||
led-2 {
|
||||
label = "light_tower1";
|
||||
gpios = <&gpio4 22 GPIO_ACTIVE_HIGH>;
|
||||
linux,default-trigger = "heartbeat";
|
||||
};
|
||||
|
||||
led-3 {
|
||||
label = "light_tower2";
|
||||
gpios = <&gpio4 23 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
|
||||
led-4 {
|
||||
label = "light_tower3";
|
||||
gpios = <&gpio4 24 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
|
||||
led-5 {
|
||||
label = "light_tower4";
|
||||
gpios = <&gpio4 25 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
};
|
||||
|
||||
clk50m_phy: phy-clock {
|
||||
compatible = "fixed-clock";
|
||||
#clock-cells = <0>;
|
||||
clock-frequency = <50000000>;
|
||||
};
|
||||
|
||||
reg_5v0: regulator-5v0 {
|
||||
compatible = "regulator-fixed";
|
||||
regulator-name = "5v0";
|
||||
regulator-min-microvolt = <5000000>;
|
||||
regulator-max-microvolt = <5000000>;
|
||||
};
|
||||
};
|
||||
|
||||
&can1 {
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&pinctrl_can1>;
|
||||
xceiver-supply = <®_5v0>;
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&can2 {
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&pinctrl_can2>;
|
||||
xceiver-supply = <®_5v0>;
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&ecspi1 {
|
||||
cs-gpios = <&gpio3 19 GPIO_ACTIVE_LOW>;
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&pinctrl_ecspi1>;
|
||||
status = "okay";
|
||||
|
||||
flash@0 {
|
||||
compatible = "jedec,spi-nor";
|
||||
reg = <0>;
|
||||
spi-max-frequency = <20000000>;
|
||||
};
|
||||
};
|
||||
|
||||
&fec {
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&pinctrl_enet>;
|
||||
phy-mode = "rmii";
|
||||
clocks = <&clks IMX6QDL_CLK_ENET>,
|
||||
<&clks IMX6QDL_CLK_ENET>,
|
||||
<&clk50m_phy>;
|
||||
clock-names = "ipg", "ahb", "ptp";
|
||||
phy-handle = <&rgmii_phy>;
|
||||
status = "okay";
|
||||
|
||||
mdio {
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
|
||||
/* Microchip KSZ8081RNA PHY */
|
||||
rgmii_phy: ethernet-phy@0 {
|
||||
reg = <0>;
|
||||
interrupts-extended = <&gpio4 30 IRQ_TYPE_LEVEL_LOW>;
|
||||
reset-gpios = <&gpio4 26 GPIO_ACTIVE_LOW>;
|
||||
reset-assert-us = <10000>;
|
||||
reset-deassert-us = <300>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&gpio1 {
|
||||
gpio-line-names =
|
||||
"", "SD1_CD", "", "", "", "", "", "",
|
||||
"DEBUG_0", "DEBUG_1", "", "", "", "", "", "",
|
||||
"", "", "", "", "", "", "", "",
|
||||
"", "", "", "", "", "", "", "";
|
||||
};
|
||||
|
||||
&gpio3 {
|
||||
gpio-line-names =
|
||||
"", "", "", "", "", "", "", "",
|
||||
"", "", "", "", "", "", "", "",
|
||||
"", "", "", "ECSPI1_SS1", "", "USB_EXT_PWR", "", "",
|
||||
"", "", "", "", "", "", "", "";
|
||||
};
|
||||
|
||||
&gpio4 {
|
||||
gpio-line-names =
|
||||
"", "", "", "", "", "", "", "",
|
||||
"", "", "", "", "CAN1_SR", "CAN2_SR", "", "",
|
||||
"LED_DI0_DEBUG_0", "LED_DI0_DEBUG_1", "IMX6_IN12", "IMX6_HMI",
|
||||
"IMX6_IN11", "IMX6_BUZZER", "IMX6_LED1", "IMX6_LED2",
|
||||
"IMX6_LED3", "IMX6_LED4", "ETH_RESET", "IMX6_ANA_OUT_SD",
|
||||
"IMX6_ANA_OUT_ERR", "IMX6_ANA_OUT", "ETH_INTRP", "";
|
||||
};
|
||||
|
||||
&gpio5 {
|
||||
gpio-line-names =
|
||||
"", "", "", "", "", "IMX6_RELAY1", "IMX6_RELAY2", "",
|
||||
"IMX6_IN1", "IMX6_IN2", "IMX6_IN3", "IMX6_IN4", "IMX6_IN5",
|
||||
"IMX6_IN6", "IMX6_IN7", "IMX6_IN8",
|
||||
"IMX6_IN9", "IMX6_IN10", "", "", "", "", "", "",
|
||||
"", "", "", "", "", "", "", "";
|
||||
};
|
||||
|
||||
&i2c1 {
|
||||
clock-frequency = <100000>;
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&pinctrl_i2c1>;
|
||||
status = "okay";
|
||||
|
||||
/* additional i2c devices are added automatically by the boot loader */
|
||||
};
|
||||
|
||||
&i2c3 {
|
||||
clock-frequency = <100000>;
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&pinctrl_i2c3>;
|
||||
status = "okay";
|
||||
|
||||
temperature-sensor@70 {
|
||||
compatible = "ti,tmp103";
|
||||
reg = <0x70>;
|
||||
};
|
||||
|
||||
rtc@51 {
|
||||
compatible = "nxp,pcf8563";
|
||||
reg = <0x51>;
|
||||
};
|
||||
};
|
||||
|
||||
&pwm1 {
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&pinctrl_pwm1>;
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&uart1 {
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&pinctrl_uart1>;
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&uart2 {
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&pinctrl_uart2>;
|
||||
fsl,uart-has-rtscts;
|
||||
linux,rs485-enabled-at-boot-time;
|
||||
rs485-rts-delay = <0 20>;
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&uart4 {
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&pinctrl_uart4>;
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&usbotg {
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&pinctrl_usbotg>;
|
||||
phy_type = "utmi";
|
||||
dr_mode = "host";
|
||||
disable-over-current;
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&usbphynop1 {
|
||||
status = "disabled";
|
||||
};
|
||||
|
||||
&usbphynop2 {
|
||||
status = "disabled";
|
||||
};
|
||||
|
||||
&iomuxc {
|
||||
pinctrl_can1: can1grp {
|
||||
fsl,pins = <
|
||||
MX6QDL_PAD_KEY_ROW2__FLEXCAN1_RX 0x1b000
|
||||
MX6QDL_PAD_KEY_COL2__FLEXCAN1_TX 0x3008
|
||||
/* CAN1_SR */
|
||||
MX6QDL_PAD_KEY_COL3__GPIO4_IO12 0x13008
|
||||
>;
|
||||
};
|
||||
|
||||
pinctrl_can2: can2grp {
|
||||
fsl,pins = <
|
||||
MX6QDL_PAD_KEY_ROW4__FLEXCAN2_RX 0x1b000
|
||||
MX6QDL_PAD_KEY_COL4__FLEXCAN2_TX 0x3008
|
||||
/* CAN2_SR */
|
||||
MX6QDL_PAD_KEY_ROW3__GPIO4_IO13 0x13008
|
||||
>;
|
||||
};
|
||||
|
||||
pinctrl_ecspi1: ecspi1grp {
|
||||
fsl,pins = <
|
||||
MX6QDL_PAD_EIM_D17__ECSPI1_MISO 0x1b000
|
||||
MX6QDL_PAD_EIM_D18__ECSPI1_MOSI 0x3008
|
||||
MX6QDL_PAD_EIM_D16__ECSPI1_SCLK 0x3008
|
||||
/* CS */
|
||||
MX6QDL_PAD_EIM_D19__GPIO3_IO19 0x3008
|
||||
>;
|
||||
};
|
||||
|
||||
pinctrl_enet: enetgrp {
|
||||
fsl,pins = <
|
||||
/* MX6QDL_ENET_PINGRP4 */
|
||||
MX6QDL_PAD_ENET_MDC__ENET_MDC 0x1b0b0
|
||||
MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x1b0b0
|
||||
MX6QDL_PAD_ENET_RXD0__ENET_RX_DATA0 0x1b0b0
|
||||
MX6QDL_PAD_ENET_RXD1__ENET_RX_DATA1 0x1b0b0
|
||||
MX6QDL_PAD_ENET_RX_ER__ENET_RX_ER 0x1b0b0
|
||||
MX6QDL_PAD_ENET_TX_EN__ENET_TX_EN 0x1b0b0
|
||||
MX6QDL_PAD_ENET_TXD0__ENET_TX_DATA0 0x1b0b0
|
||||
MX6QDL_PAD_ENET_TXD1__ENET_TX_DATA1 0x1b0b0
|
||||
MX6QDL_PAD_ENET_CRS_DV__ENET_RX_EN 0x1b0b0
|
||||
|
||||
MX6QDL_PAD_GPIO_16__ENET_REF_CLK 0x1b0b0
|
||||
/* Phy reset */
|
||||
MX6QDL_PAD_DISP0_DAT5__GPIO4_IO26 0x1b0b0
|
||||
/* nINTRP */
|
||||
MX6QDL_PAD_DISP0_DAT9__GPIO4_IO30 0x1b0b0
|
||||
>;
|
||||
};
|
||||
|
||||
pinctrl_i2c1: i2c1grp {
|
||||
fsl,pins = <
|
||||
MX6QDL_PAD_CSI0_DAT8__I2C1_SDA 0x4001f8b1
|
||||
MX6QDL_PAD_CSI0_DAT9__I2C1_SCL 0x4001f8b1
|
||||
>;
|
||||
};
|
||||
|
||||
pinctrl_i2c3: i2c3grp {
|
||||
fsl,pins = <
|
||||
MX6QDL_PAD_GPIO_5__I2C3_SCL 0x4001b8b1
|
||||
MX6QDL_PAD_GPIO_6__I2C3_SDA 0x4001b8b1
|
||||
>;
|
||||
};
|
||||
|
||||
pinctrl_leds: ledsgrp {
|
||||
fsl,pins = <
|
||||
/* DEBUG_0 */
|
||||
MX6QDL_PAD_GPIO_8__GPIO1_IO08 0x1b0b0
|
||||
/* DEBUG_1 */
|
||||
MX6QDL_PAD_GPIO_9__GPIO1_IO09 0x1b0b0
|
||||
|
||||
/* LED1 (lighttower) */
|
||||
MX6QDL_PAD_DISP0_DAT1__GPIO4_IO22 0x13070
|
||||
/* LED2 (lighttower) */
|
||||
MX6QDL_PAD_DISP0_DAT2__GPIO4_IO23 0x13070
|
||||
/* LED3 (lighttower) */
|
||||
MX6QDL_PAD_DISP0_DAT3__GPIO4_IO24 0x13070
|
||||
/* LED4 (lighttower) */
|
||||
MX6QDL_PAD_DISP0_DAT4__GPIO4_IO25 0x13070
|
||||
>;
|
||||
};
|
||||
|
||||
pinctrl_pwm1: pwm1grp {
|
||||
fsl,pins = <
|
||||
MX6QDL_PAD_DISP0_DAT8__PWM1_OUT 0x1b0b0
|
||||
>;
|
||||
};
|
||||
|
||||
/* YaCO AUX Uart */
|
||||
pinctrl_uart1: uart1grp {
|
||||
fsl,pins = <
|
||||
MX6QDL_PAD_CSI0_DAT10__UART1_TX_DATA 0x1b0b1
|
||||
MX6QDL_PAD_CSI0_DAT11__UART1_RX_DATA 0x1b0b1
|
||||
>;
|
||||
};
|
||||
|
||||
pinctrl_uart2: uart2grp {
|
||||
fsl,pins = <
|
||||
MX6QDL_PAD_EIM_D26__UART2_TX_DATA 0x1b0b1
|
||||
MX6QDL_PAD_EIM_D27__UART2_RX_DATA 0x1b0b1
|
||||
MX6QDL_PAD_EIM_D28__UART2_DTE_CTS_B 0x130b1
|
||||
>;
|
||||
};
|
||||
|
||||
pinctrl_uart4: uart4grp {
|
||||
fsl,pins = <
|
||||
MX6QDL_PAD_KEY_COL0__UART4_TX_DATA 0x1b0b1
|
||||
MX6QDL_PAD_KEY_ROW0__UART4_RX_DATA 0x1b0b1
|
||||
>;
|
||||
};
|
||||
|
||||
pinctrl_usbotg: usbotggrp {
|
||||
fsl,pins = <
|
||||
MX6QDL_PAD_EIM_D21__USB_OTG_OC 0x1b0b0
|
||||
/* power enable, high active */
|
||||
MX6QDL_PAD_EIM_D22__GPIO3_IO22 0x1b0b0
|
||||
>;
|
||||
};
|
||||
|
||||
pinctrl_usdhc1: usdhc1grp {
|
||||
fsl,pins = <
|
||||
MX6QDL_PAD_SD1_CMD__SD1_CMD 0x170f9
|
||||
MX6QDL_PAD_SD1_CLK__SD1_CLK 0x100f9
|
||||
MX6QDL_PAD_SD1_DAT0__SD1_DATA0 0x170f9
|
||||
MX6QDL_PAD_SD1_DAT1__SD1_DATA1 0x170f9
|
||||
MX6QDL_PAD_SD1_DAT2__SD1_DATA2 0x170f9
|
||||
MX6QDL_PAD_SD1_DAT3__SD1_DATA3 0x170f9
|
||||
MX6QDL_PAD_GPIO_1__GPIO1_IO01 0x1b0b0
|
||||
>;
|
||||
};
|
||||
|
||||
pinctrl_usdhc3: usdhc3grp {
|
||||
fsl,pins = <
|
||||
MX6QDL_PAD_SD3_CMD__SD3_CMD 0x17099
|
||||
MX6QDL_PAD_SD3_CLK__SD3_CLK 0x10099
|
||||
MX6QDL_PAD_SD3_DAT0__SD3_DATA0 0x17099
|
||||
MX6QDL_PAD_SD3_DAT1__SD3_DATA1 0x17099
|
||||
MX6QDL_PAD_SD3_DAT2__SD3_DATA2 0x17099
|
||||
MX6QDL_PAD_SD3_DAT3__SD3_DATA3 0x17099
|
||||
MX6QDL_PAD_SD3_DAT4__SD3_DATA4 0x17099
|
||||
MX6QDL_PAD_SD3_DAT5__SD3_DATA5 0x17099
|
||||
MX6QDL_PAD_SD3_DAT6__SD3_DATA6 0x17099
|
||||
MX6QDL_PAD_SD3_DAT7__SD3_DATA7 0x17099
|
||||
MX6QDL_PAD_SD3_RST__SD3_RESET 0x1b0b1
|
||||
>;
|
||||
};
|
||||
};
|
||||
Loading…
Reference in New Issue