diff --git a/arch/arm64/boot/dts/qcom/apq8016-sbc.dtsi b/arch/arm64/boot/dts/qcom/apq8016-sbc.dtsi
index 46feedf7c989..134617d87a1a 100644
--- a/arch/arm64/boot/dts/qcom/apq8016-sbc.dtsi
+++ b/arch/arm64/boot/dts/qcom/apq8016-sbc.dtsi
@@ -644,6 +644,8 @@
 	l11 {
 		regulator-min-microvolt = <1750000>;
 		regulator-max-microvolt = <3337000>;
+		regulator-allow-set-load;
+		regulator-system-load = <200000>;
 	};
 
 	l12 {
diff --git a/arch/arm64/boot/dts/qcom/msm8996-pins.dtsi b/arch/arm64/boot/dts/qcom/msm8996-pins.dtsi
index 8d5114d16d09..131878db9852 100644
--- a/arch/arm64/boot/dts/qcom/msm8996-pins.dtsi
+++ b/arch/arm64/boot/dts/qcom/msm8996-pins.dtsi
@@ -139,7 +139,7 @@
 		};
 
 		pinconf {
-			pins = "gpio4", "gpiio5", "gpio6", "gpio7";
+			pins = "gpio4", "gpio5", "gpio6", "gpio7";
 			drive-strength = <2>;
 			bias-disable;
 		};
diff --git a/arch/arm64/boot/dts/qcom/msm8996.dtsi b/arch/arm64/boot/dts/qcom/msm8996.dtsi
index 99b7495455a6..c761269caf80 100644
--- a/arch/arm64/boot/dts/qcom/msm8996.dtsi
+++ b/arch/arm64/boot/dts/qcom/msm8996.dtsi
@@ -306,6 +306,40 @@
 				#clock-cells = <1>;
 			};
 
+			rpmpd: power-controller {
+				compatible = "qcom,msm8996-rpmpd";
+				#power-domain-cells = <1>;
+				operating-points-v2 = <&rpmpd_opp_table>;
+
+				rpmpd_opp_table: opp-table {
+					compatible = "operating-points-v2";
+
+					rpmpd_opp1: opp1 {
+						opp-level = <1>;
+					};
+
+					rpmpd_opp2: opp2 {
+						opp-level = <2>;
+					};
+
+					rpmpd_opp3: opp3 {
+						opp-level = <3>;
+					};
+
+					rpmpd_opp4: opp4 {
+						opp-level = <4>;
+					};
+
+					rpmpd_opp5: opp5 {
+						opp-level = <5>;
+					};
+
+					rpmpd_opp6: opp6 {
+						opp-level = <6>;
+					};
+				};
+			};
+
 			pm8994-regulators {
 				compatible = "qcom,rpm-pm8994-regulators";
 
@@ -404,7 +438,7 @@
 		};
 
 		intc: interrupt-controller@9bc0000 {
-			compatible = "arm,gic-v3";
+			compatible = "qcom,msm8996-gic-v3", "arm,gic-v3";
 			#interrupt-cells = <3>;
 			interrupt-controller;
 			#redistributor-regions = <1>;
@@ -966,7 +1000,7 @@
 			clock-names = "iface",
 				      "bus";
 			#iommu-cells = <1>;
-			status = "ok";
+			status = "disabled";
 		};
 
 		camss: camss@a00000 {
diff --git a/arch/arm64/boot/dts/qcom/msm8998-mtp.dtsi b/arch/arm64/boot/dts/qcom/msm8998-mtp.dtsi
index 50e9033aa7f6..f0901067b043 100644
--- a/arch/arm64/boot/dts/qcom/msm8998-mtp.dtsi
+++ b/arch/arm64/boot/dts/qcom/msm8998-mtp.dtsi
@@ -65,6 +65,13 @@
 	status = "okay";
 };
 
+&qusb2phy {
+	status = "okay";
+
+	vdda-pll-supply = <&vreg_l12a_1p8>;
+	vdda-phy-dpdm-supply = <&vreg_l24a_3p075>;
+};
+
 &rpm_requests {
 	pm8998-regulators {
 		compatible = "qcom,rpm-pm8998-regulators";
@@ -192,6 +199,8 @@
 		vreg_l21a_2p95: l21 {
 			regulator-min-microvolt = <2960000>;
 			regulator-max-microvolt = <2960000>;
+			regulator-allow-set-load;
+			regulator-system-load = <800000>;
 		};
 		vreg_l22a_2p85: l22 {
 			regulator-min-microvolt = <2864000>;
@@ -257,3 +266,18 @@
 	pinctrl-0 = <&sdc2_clk_on  &sdc2_cmd_on  &sdc2_data_on  &sdc2_cd_on>;
 	pinctrl-1 = <&sdc2_clk_off &sdc2_cmd_off &sdc2_data_off &sdc2_cd_off>;
 };
+
+&usb3 {
+	status = "okay";
+};
+
+&usb3_dwc3 {
+	dr_mode = "host"; /* Force to host until we have Type-C hooked up */
+};
+
+&usb3phy {
+	status = "okay";
+
+	vdda-phy-supply = <&vreg_l1a_0p875>;
+	vdda-pll-supply = <&vreg_l2a_1p2>;
+};
diff --git a/arch/arm64/boot/dts/qcom/msm8998.dtsi b/arch/arm64/boot/dts/qcom/msm8998.dtsi
index 8d41b69ec2da..5091ac07a2af 100644
--- a/arch/arm64/boot/dts/qcom/msm8998.dtsi
+++ b/arch/arm64/boot/dts/qcom/msm8998.dtsi
@@ -3,6 +3,7 @@
 
 #include <dt-bindings/interrupt-controller/arm-gic.h>
 #include <dt-bindings/clock/qcom,gcc-msm8998.h>
+#include <dt-bindings/clock/qcom,rpmcc.h>
 #include <dt-bindings/gpio/gpio.h>
 
 / {
@@ -266,6 +267,11 @@
 		rpm_requests: rpm-requests {
 			compatible = "qcom,rpm-msm8998";
 			qcom,glink-channels = "rpm_requests";
+
+			rpmcc: clock-controller {
+				compatible = "qcom,rpmcc-msm8998", "qcom,rpmcc";
+				#clock-cells = <1>;
+			};
 		};
 	};
 
@@ -540,6 +546,11 @@
 			reg = <0x780000 0x621c>;
 			#address-cells = <1>;
 			#size-cells = <1>;
+
+			qusb2_hstx_trim: hstx-trim@423a {
+				reg = <0x423a 0x1>;
+				bits = <0 4>;
+			};
 		};
 
 		gcc: clock-controller@100000 {
@@ -607,6 +618,93 @@
 			#mbox-cells = <1>;
 		};
 
+		usb3: usb@a8f8800 {
+			compatible = "qcom,msm8998-dwc3", "qcom,dwc3";
+			reg = <0x0a8f8800 0x400>;
+			status = "disabled";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
+
+			clocks = <&gcc GCC_CFG_NOC_USB3_AXI_CLK>,
+				 <&gcc GCC_USB30_MASTER_CLK>,
+				 <&gcc GCC_AGGRE1_USB3_AXI_CLK>,
+				 <&gcc GCC_USB30_MOCK_UTMI_CLK>,
+				 <&gcc GCC_USB30_SLEEP_CLK>;
+			clock-names = "cfg_noc", "core", "iface", "mock_utmi",
+				      "sleep";
+
+			assigned-clocks = <&gcc GCC_USB30_MOCK_UTMI_CLK>,
+					  <&gcc GCC_USB30_MASTER_CLK>;
+			assigned-clock-rates = <19200000>, <120000000>;
+
+			interrupts = <GIC_SPI 347 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 243 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "hs_phy_irq", "ss_phy_irq";
+
+			power-domains = <&gcc USB_30_GDSC>;
+
+			resets = <&gcc GCC_USB_30_BCR>;
+
+			usb3_dwc3: dwc3@a800000 {
+				compatible = "snps,dwc3";
+				reg = <0x0a800000 0xcd00>;
+				interrupts = <GIC_SPI 131 IRQ_TYPE_LEVEL_HIGH>;
+				snps,dis_u2_susphy_quirk;
+				snps,dis_enblslpm_quirk;
+				phys = <&qusb2phy>, <&usb1_ssphy>;
+				phy-names = "usb2-phy", "usb3-phy";
+				snps,has-lpm-erratum;
+				snps,hird-threshold = /bits/ 8 <0x10>;
+			};
+		};
+
+		usb3phy: phy@c010000 {
+			compatible = "qcom,msm8998-qmp-usb3-phy";
+			reg = <0x0c010000 0x18c>;
+			status = "disabled";
+			#clock-cells = <1>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
+
+			clocks = <&gcc GCC_USB3_PHY_AUX_CLK>,
+				 <&gcc GCC_USB_PHY_CFG_AHB2PHY_CLK>,
+				 <&gcc GCC_USB3_CLKREF_CLK>;
+			clock-names = "aux", "cfg_ahb", "ref";
+
+			resets = <&gcc GCC_USB3_PHY_BCR>,
+				 <&gcc GCC_USB3PHY_PHY_BCR>;
+			reset-names = "phy", "common";
+
+			usb1_ssphy: lane@c010200 {
+				reg = <0xc010200 0x128>,
+				      <0xc010400 0x200>,
+				      <0xc010c00 0x20c>,
+				      <0xc010600 0x128>,
+				      <0xc010800 0x200>;
+				#phy-cells = <0>;
+				clocks = <&gcc GCC_USB3_PHY_PIPE_CLK>;
+				clock-names = "pipe0";
+				clock-output-names = "usb3_phy_pipe_clk_src";
+			};
+		};
+
+		qusb2phy: phy@c012000 {
+			compatible = "qcom,msm8998-qusb2-phy";
+			reg = <0x0c012000 0x2a8>;
+			status = "disabled";
+			#phy-cells = <0>;
+
+			clocks = <&gcc GCC_USB_PHY_CFG_AHB2PHY_CLK>,
+				 <&gcc GCC_RX1_USB2_CLKREF_CLK>;
+			clock-names = "cfg_ahb", "ref";
+
+			resets = <&gcc GCC_QUSB2PHY_PRIM_BCR>;
+
+			nvmem-cells = <&qusb2_hstx_trim>;
+		};
+
 		sdhc2: sdhci@c0a4900 {
 			compatible = "qcom,sdhci-msm-v4";
 			reg = <0xc0a4900 0x314>, <0xc0a4000 0x800>;
@@ -624,6 +722,186 @@
 			status = "disabled";
 		};
 
+		blsp1_i2c1: i2c@c175000 {
+			compatible = "qcom,i2c-qup-v2.2.1";
+			reg = <0x0c175000 0x600>;
+			interrupts = <GIC_SPI 95 IRQ_TYPE_LEVEL_HIGH>;
+
+			clocks = <&gcc GCC_BLSP1_QUP1_I2C_APPS_CLK>,
+				 <&gcc GCC_BLSP1_AHB_CLK>;
+			clock-names = "core", "iface";
+			clock-frequency = <400000>;
+
+			status = "disabled";
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		blsp1_i2c2: i2c@c176000 {
+			compatible = "qcom,i2c-qup-v2.2.1";
+			reg = <0x0c176000 0x600>;
+			interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>;
+
+			clocks = <&gcc GCC_BLSP1_QUP2_I2C_APPS_CLK>,
+				 <&gcc GCC_BLSP1_AHB_CLK>;
+			clock-names = "core", "iface";
+			clock-frequency = <400000>;
+
+			status = "disabled";
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		blsp1_i2c3: i2c@c177000 {
+			compatible = "qcom,i2c-qup-v2.2.1";
+			reg = <0x0c177000 0x600>;
+			interrupts = <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>;
+
+			clocks = <&gcc GCC_BLSP1_QUP3_I2C_APPS_CLK>,
+				 <&gcc GCC_BLSP1_AHB_CLK>;
+			clock-names = "core", "iface";
+			clock-frequency = <400000>;
+
+			status = "disabled";
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		blsp1_i2c4: i2c@c178000 {
+			compatible = "qcom,i2c-qup-v2.2.1";
+			reg = <0x0c178000 0x600>;
+			interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>;
+
+			clocks = <&gcc GCC_BLSP1_QUP4_I2C_APPS_CLK>,
+				 <&gcc GCC_BLSP1_AHB_CLK>;
+			clock-names = "core", "iface";
+			clock-frequency = <400000>;
+
+			status = "disabled";
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		blsp1_i2c5: i2c@c179000 {
+			compatible = "qcom,i2c-qup-v2.2.1";
+			reg = <0x0c179000 0x600>;
+			interrupts = <GIC_SPI 99 IRQ_TYPE_LEVEL_HIGH>;
+
+			clocks = <&gcc GCC_BLSP1_QUP5_I2C_APPS_CLK>,
+				 <&gcc GCC_BLSP1_AHB_CLK>;
+			clock-names = "core", "iface";
+			clock-frequency = <400000>;
+
+			status = "disabled";
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		blsp1_i2c6: i2c@c17a000 {
+			compatible = "qcom,i2c-qup-v2.2.1";
+			reg = <0x0c17a000 0x600>;
+			interrupts = <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>;
+
+			clocks = <&gcc GCC_BLSP1_QUP6_I2C_APPS_CLK>,
+				 <&gcc GCC_BLSP1_AHB_CLK>;
+			clock-names = "core", "iface";
+			clock-frequency = <400000>;
+
+			status = "disabled";
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		blsp2_i2c0: i2c@c1b5000 {
+			compatible = "qcom,i2c-qup-v2.2.1";
+			reg = <0x0c1b5000 0x600>;
+			interrupts = <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>;
+
+			clocks = <&gcc GCC_BLSP2_QUP1_I2C_APPS_CLK>,
+				 <&gcc GCC_BLSP2_AHB_CLK>;
+			clock-names = "core", "iface";
+			clock-frequency = <400000>;
+
+			status = "disabled";
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		blsp2_i2c1: i2c@c1b6000 {
+			compatible = "qcom,i2c-qup-v2.2.1";
+			reg = <0x0c1b6000 0x600>;
+			interrupts = <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>;
+
+			clocks = <&gcc GCC_BLSP2_QUP2_I2C_APPS_CLK>,
+				 <&gcc GCC_BLSP2_AHB_CLK>;
+			clock-names = "core", "iface";
+			clock-frequency = <400000>;
+
+			status = "disabled";
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		blsp2_i2c2: i2c@c1b7000 {
+			compatible = "qcom,i2c-qup-v2.2.1";
+			reg = <0x0c1b7000 0x600>;
+			interrupts = <GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>;
+
+			clocks = <&gcc GCC_BLSP2_QUP3_I2C_APPS_CLK>,
+				 <&gcc GCC_BLSP2_AHB_CLK>;
+			clock-names = "core", "iface";
+			clock-frequency = <400000>;
+
+			status = "disabled";
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		blsp2_i2c3: i2c@c1b8000 {
+			compatible = "qcom,i2c-qup-v2.2.1";
+			reg = <0x0c1b8000 0x600>;
+			interrupts = <GIC_SPI 104 IRQ_TYPE_LEVEL_HIGH>;
+
+			clocks = <&gcc GCC_BLSP2_QUP4_I2C_APPS_CLK>,
+				 <&gcc GCC_BLSP2_AHB_CLK>;
+			clock-names = "core", "iface";
+			clock-frequency = <400000>;
+
+			status = "disabled";
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		blsp2_i2c4: i2c@c1b9000 {
+			compatible = "qcom,i2c-qup-v2.2.1";
+			reg = <0x0c1b9000 0x600>;
+			interrupts = <GIC_SPI 105 IRQ_TYPE_LEVEL_HIGH>;
+
+			clocks = <&gcc GCC_BLSP2_QUP5_I2C_APPS_CLK>,
+				 <&gcc GCC_BLSP2_AHB_CLK>;
+			clock-names = "core", "iface";
+			clock-frequency = <400000>;
+
+			status = "disabled";
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		blsp2_i2c5: i2c@c1ba000 {
+			compatible = "qcom,i2c-qup-v2.2.1";
+			reg = <0x0c175000 0x600>;
+			interrupts = <GIC_SPI 106 IRQ_TYPE_LEVEL_HIGH>;
+
+			clocks = <&gcc GCC_BLSP2_QUP6_I2C_APPS_CLK>,
+				 <&gcc GCC_BLSP2_AHB_CLK>;
+			clock-names = "core", "iface";
+			clock-frequency = <400000>;
+
+			status = "disabled";
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
 		blsp2_uart1: serial@c1b0000 {
 			compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm";
 			reg = <0xc1b0000 0x1000>;
diff --git a/arch/arm64/boot/dts/qcom/pm8916.dtsi b/arch/arm64/boot/dts/qcom/pm8916.dtsi
index 15a37cbcd216..9dd2df1cbf47 100644
--- a/arch/arm64/boot/dts/qcom/pm8916.dtsi
+++ b/arch/arm64/boot/dts/qcom/pm8916.dtsi
@@ -32,6 +32,12 @@
 				bias-pull-up;
 				linux,code = <KEY_POWER>;
 			};
+
+			watchdog {
+				compatible = "qcom,pm8916-wdt";
+				interrupts = <0x0 0x8 6 IRQ_TYPE_EDGE_RISING>;
+				timeout-sec = <60>;
+			};
 		};
 
 		pm8916_gpios: gpios@c000 {
diff --git a/arch/arm64/boot/dts/qcom/pms405.dtsi b/arch/arm64/boot/dts/qcom/pms405.dtsi
index ad2b62dfc9f6..1bb836d1e8aa 100644
--- a/arch/arm64/boot/dts/qcom/pms405.dtsi
+++ b/arch/arm64/boot/dts/qcom/pms405.dtsi
@@ -3,6 +3,32 @@
 
 #include <dt-bindings/spmi/spmi.h>
 #include <dt-bindings/input/linux-event-codes.h>
+#include <dt-bindings/iio/qcom,spmi-vadc.h>
+#include <dt-bindings/thermal/thermal.h>
+
+/ {
+	thermal-zones {
+		pms405 {
+			polling-delay-passive = <250>;
+			polling-delay = <1000>;
+
+			thermal-sensors = <&pms405_temp>;
+
+			trips {
+				pms405_alert0: pms405-alert0 {
+					temperature = <105000>;
+					hysteresis = <2000>;
+					type = "passive";
+				};
+				pms405_crit: pms405-crit {
+					temperature = <125000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+			};
+		};
+	};
+};
 
 &spmi_bus {
 	pms405_0: pms405@0 {
@@ -45,6 +71,59 @@
 			};
 		};
 
+		pms405_temp: temp-alarm@2400 {
+			compatible = "qcom,spmi-temp-alarm";
+			reg = <0x2400>;
+			interrupts = <0 0x24 0 IRQ_TYPE_EDGE_RISING>;
+			io-channels = <&pms405_adc ADC5_DIE_TEMP>;
+			io-channel-names = "thermal";
+			#thermal-sensor-cells = <0>;
+		};
+
+		pms405_adc: adc@3100 {
+			compatible = "qcom,pms405-adc", "qcom,spmi-adc-rev2";
+			reg = <0x3100>;
+			interrupts = <0x0 0x31 0x0 IRQ_TYPE_EDGE_RISING>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			#io-channel-cells = <1>;
+
+			ref_gnd {
+				reg = <ADC5_REF_GND>;
+				qcom,pre-scaling = <1 1>;
+			};
+
+			vref_1p25 {
+				reg = <ADC5_1P25VREF>;
+				qcom,pre-scaling = <1 1>;
+			};
+
+			vph_pwr {
+				reg = <ADC5_VPH_PWR>;
+				qcom,pre-scaling = <1 3>;
+			};
+
+			die_temp {
+				reg = <ADC5_DIE_TEMP>;
+				qcom,pre-scaling = <1 1>;
+			};
+
+			xo_therm_100k_pu {
+				reg = <ADC5_XO_THERM_100K_PU>;
+				qcom,pre-scaling = <1 1>;
+			};
+
+			amux_thm1_100k_pu {
+				reg = <ADC5_AMUX_THM1_100K_PU>;
+				qcom,pre-scaling = <1 1>;
+			};
+
+			amux_thm3_100k_pu {
+				reg = <ADC5_AMUX_THM3_100K_PU>;
+				qcom,pre-scaling = <1 1>;
+			};
+		};
+
 		rtc@6000 {
 			compatible = "qcom,pm8941-rtc";
 			reg = <0x6000>;
diff --git a/arch/arm64/boot/dts/qcom/qcs404-evb.dtsi b/arch/arm64/boot/dts/qcom/qcs404-evb.dtsi
index a39924efebe4..50b3589c7f15 100644
--- a/arch/arm64/boot/dts/qcom/qcs404-evb.dtsi
+++ b/arch/arm64/boot/dts/qcom/qcs404-evb.dtsi
@@ -127,6 +127,7 @@
 	status = "ok";
 
 	mmc-ddr-1_8v;
+	mmc-hs400-1_8v;
 	bus-width = <8>;
 	non-removable;
 
@@ -186,3 +187,21 @@
 		};
 	};
 };
+
+&wifi {
+	status = "okay";
+};
+
+/* PINCTRL - additions to nodes defined in qcs404.dtsi */
+
+&blsp1_uart2_default {
+	rx {
+		drive-strength = <2>;
+		bias-disable;
+	};
+
+	tx {
+		drive-strength = <2>;
+		bias-disable;
+	};
+};
diff --git a/arch/arm64/boot/dts/qcom/qcs404.dtsi b/arch/arm64/boot/dts/qcom/qcs404.dtsi
index 9b5c16562bbe..e8fd26633d57 100644
--- a/arch/arm64/boot/dts/qcom/qcs404.dtsi
+++ b/arch/arm64/boot/dts/qcom/qcs404.dtsi
@@ -3,6 +3,7 @@
 
 #include <dt-bindings/interrupt-controller/arm-gic.h>
 #include <dt-bindings/clock/qcom,gcc-qcs404.h>
+#include <dt-bindings/clock/qcom,rpmcc.h>
 
 / {
 	interrupt-parent = <&intc>;
@@ -224,6 +225,11 @@
 		rpm_requests: glink-channel {
 			compatible = "qcom,rpm-qcs404";
 			qcom,glink-channels = "rpm_requests";
+
+			rpmcc: clock-controller {
+				compatible = "qcom,rpmcc-qcs404";
+				#clock-cells = <1>;
+			};
 		};
 	};
 
@@ -272,6 +278,105 @@
 			#gpio-cells = <2>;
 			interrupt-controller;
 			#interrupt-cells = <2>;
+
+			blsp1_i2c0_default: blsp1-i2c0-default {
+				pins = "gpio32", "gpio33";
+				function = "blsp_i2c0";
+			};
+
+			blsp1_i2c1_default: blsp1-i2c1-default {
+				pins = "gpio24", "gpio25";
+				function = "blsp_i2c1";
+			};
+
+			blsp1_i2c2_default: blsp1-i2c2-default {
+				sda {
+					pins = "gpio19";
+					function = "blsp_i2c_sda_a2";
+				};
+
+				scl {
+					pins = "gpio20";
+					function = "blsp_i2c_scl_a2";
+				};
+			};
+
+			blsp1_i2c3_default: blsp1-i2c3-default {
+				pins = "gpio84", "gpio85";
+				function = "blsp_i2c3";
+			};
+
+			blsp1_i2c4_default: blsp1-i2c4-default {
+				pins = "gpio117", "gpio118";
+				function = "blsp_i2c4";
+			};
+
+			blsp1_uart0_default: blsp1-uart0-default {
+				pins = "gpio30", "gpio31", "gpio32", "gpio33";
+				function = "blsp_uart0";
+			};
+
+			blsp1_uart1_default: blsp1-uart1-default {
+				pins = "gpio22", "gpio23";
+				function = "blsp_uart1";
+			};
+
+			blsp1_uart2_default: blsp1-uart2-default {
+				rx {
+					pins = "gpio18";
+					function = "blsp_uart_rx_a2";
+				};
+
+				tx {
+					pins = "gpio17";
+					function = "blsp_uart_tx_a2";
+				};
+			};
+
+			blsp1_uart3_default: blsp1-uart3-default {
+				pins = "gpio82", "gpio83", "gpio84", "gpio85";
+				function = "blsp_uart3";
+			};
+
+			blsp2_i2c0_default: blsp2-i2c0-default {
+				pins = "gpio28", "gpio29";
+				function = "blsp_i2c5";
+			};
+
+			blsp1_spi0_default: blsp1-spi0-default {
+				pins = "gpio30", "gpio31", "gpio32", "gpio33";
+				function = "blsp_spi0";
+			};
+
+			blsp1_spi1_default: blsp1-spi1-default {
+				pins = "gpio22", "gpio23", "gpio24", "gpio25";
+				function = "blsp_spi1";
+			};
+
+			blsp1_spi2_default: blsp1-spi2-default {
+				pins = "gpio17", "gpio18", "gpio19", "gpio20";
+				function = "blsp_spi2";
+			};
+
+			blsp1_spi3_default: blsp1-spi3-default {
+				pins = "gpio82", "gpio83", "gpio84", "gpio85";
+				function = "blsp_spi3";
+			};
+
+			blsp1_spi4_default: blsp1-spi4-default {
+				pins = "gpio37", "gpio38", "gpio117", "gpio118";
+				function = "blsp_spi4";
+			};
+
+			blsp2_spi0_default: blsp2-spi0-default {
+				pins = "gpio26", "gpio27", "gpio28", "gpio29";
+				function = "blsp_spi5";
+			};
+
+			blsp2_uart0_default: blsp2-uart0-default {
+				pins = "gpio26", "gpio27", "gpio28", "gpio29";
+				function = "blsp_uart5";
+			};
 		};
 
 		gcc: clock-controller@1800000 {
@@ -335,6 +440,32 @@
 			status = "okay";
 		};
 
+		blsp1_uart0: serial@78af000 {
+			compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm";
+			reg = <0x078af000 0x200>;
+			interrupts = <GIC_SPI 107 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc GCC_BLSP1_UART0_APPS_CLK>, <&gcc GCC_BLSP1_AHB_CLK>;
+			clock-names = "core", "iface";
+			dmas = <&blsp1_dma 1>, <&blsp1_dma 0>;
+			dma-names = "rx", "tx";
+			pinctrl-names = "default";
+			pinctrl-0 = <&blsp1_uart0_default>;
+			status = "disabled";
+		};
+
+		blsp1_uart1: serial@78b0000 {
+			compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm";
+			reg = <0x078b0000 0x200>;
+			interrupts = <GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc GCC_BLSP1_UART1_APPS_CLK>, <&gcc GCC_BLSP1_AHB_CLK>;
+			clock-names = "core", "iface";
+			dmas = <&blsp1_dma 3>, <&blsp1_dma 2>;
+			dma-names = "rx", "tx";
+			pinctrl-names = "default";
+			pinctrl-0 = <&blsp1_uart1_default>;
+			status = "disabled";
+		};
+
 		blsp1_uart2: serial@78b1000 {
 			compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm";
 			reg = <0x078b1000 0x200>;
@@ -343,9 +474,237 @@
 			clock-names = "core", "iface";
 			dmas = <&blsp1_dma 5>, <&blsp1_dma 4>;
 			dma-names = "rx", "tx";
+			pinctrl-names = "default";
+			pinctrl-0 = <&blsp1_uart2_default>;
 			status = "okay";
 		};
 
+		wifi: wifi@a000000 {
+			compatible = "qcom,wcn3990-wifi";
+			reg = <0xa000000 0x800000>;
+			reg-names = "membase";
+			memory-region = <&wlan_msa_mem>;
+			interrupts = <GIC_SPI 277 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 278 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 279 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 280 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 281 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 282 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 283 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 284 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 285 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 286 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 287 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 288 IRQ_TYPE_LEVEL_HIGH>;
+			status = "disabled";
+		};
+
+		blsp1_uart3: serial@78b2000 {
+			compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm";
+			reg = <0x078b2000 0x200>;
+			interrupts = <GIC_SPI 119 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc GCC_BLSP1_UART3_APPS_CLK>, <&gcc GCC_BLSP1_AHB_CLK>;
+			clock-names = "core", "iface";
+			dmas = <&blsp1_dma 7>, <&blsp1_dma 6>;
+			dma-names = "rx", "tx";
+			pinctrl-names = "default";
+			pinctrl-0 = <&blsp1_uart3_default>;
+			status = "disabled";
+		};
+
+		blsp1_i2c0: i2c@78b5000 {
+			compatible = "qcom,i2c-qup-v2.2.1";
+			reg = <0x078b5000 0x600>;
+			interrupts = <GIC_SPI 95 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc GCC_BLSP1_AHB_CLK>,
+				 <&gcc GCC_BLSP1_QUP0_I2C_APPS_CLK>;
+			clock-names = "iface", "core";
+			pinctrl-names = "default";
+			pinctrl-0 = <&blsp1_i2c0_default>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		blsp1_spi0: spi@78b5000 {
+			compatible = "qcom,spi-qup-v2.2.1";
+			reg = <0x078b5000 0x600>;
+			interrupts = <GIC_SPI 95 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc GCC_BLSP1_AHB_CLK>,
+				 <&gcc GCC_BLSP1_QUP0_SPI_APPS_CLK>;
+			clock-names = "iface", "core";
+			pinctrl-names = "default";
+			pinctrl-0 = <&blsp1_spi0_default>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		blsp1_i2c1: i2c@78b6000 {
+			compatible = "qcom,i2c-qup-v2.2.1";
+			reg = <0x078b6000 0x600>;
+			interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc GCC_BLSP1_AHB_CLK>,
+				 <&gcc GCC_BLSP1_QUP1_I2C_APPS_CLK>;
+			clock-names = "iface", "core";
+			pinctrl-names = "default";
+			pinctrl-0 = <&blsp1_i2c1_default>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		blsp1_spi1: spi@78b6000 {
+			compatible = "qcom,spi-qup-v2.2.1";
+			reg = <0x078b6000 0x600>;
+			interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc GCC_BLSP1_AHB_CLK>,
+				 <&gcc GCC_BLSP1_QUP1_SPI_APPS_CLK>;
+			clock-names = "iface", "core";
+			pinctrl-names = "default";
+			pinctrl-0 = <&blsp1_spi1_default>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		blsp1_i2c2: i2c@78b7000 {
+			compatible = "qcom,i2c-qup-v2.2.1";
+			reg = <0x078b7000 0x600>;
+			interrupts = <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc GCC_BLSP1_AHB_CLK>,
+				 <&gcc GCC_BLSP1_QUP2_I2C_APPS_CLK>;
+			clock-names = "iface", "core";
+			pinctrl-names = "default";
+			pinctrl-0 = <&blsp1_i2c2_default>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		blsp1_spi2: spi@78b7000 {
+			compatible = "qcom,spi-qup-v2.2.1";
+			reg = <0x078b7000 0x600>;
+			interrupts = <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc GCC_BLSP1_AHB_CLK>,
+				 <&gcc GCC_BLSP1_QUP2_SPI_APPS_CLK>;
+			clock-names = "iface", "core";
+			pinctrl-names = "default";
+			pinctrl-0 = <&blsp1_spi2_default>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		blsp1_i2c3: i2c@78b8000 {
+			compatible = "qcom,i2c-qup-v2.2.1";
+			reg = <0x078b8000 0x600>;
+			interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc GCC_BLSP1_AHB_CLK>,
+				 <&gcc GCC_BLSP1_QUP3_I2C_APPS_CLK>;
+			clock-names = "iface", "core";
+			pinctrl-names = "default";
+			pinctrl-0 = <&blsp1_i2c3_default>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		blsp1_spi3: spi@78b8000 {
+			compatible = "qcom,spi-qup-v2.2.1";
+			reg = <0x078b8000 0x600>;
+			interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc GCC_BLSP1_AHB_CLK>,
+				 <&gcc GCC_BLSP1_QUP3_SPI_APPS_CLK>;
+			clock-names = "iface", "core";
+			pinctrl-names = "default";
+			pinctrl-0 = <&blsp1_spi3_default>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		blsp1_i2c4: i2c@78b9000 {
+			compatible = "qcom,i2c-qup-v2.2.1";
+			reg = <0x078b9000 0x600>;
+			interrupts = <GIC_SPI 99 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc GCC_BLSP1_AHB_CLK>,
+				 <&gcc GCC_BLSP1_QUP4_I2C_APPS_CLK>;
+			clock-names = "iface", "core";
+			pinctrl-names = "default";
+			pinctrl-0 = <&blsp1_i2c4_default>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		blsp1_spi4: spi@78b9000 {
+			compatible = "qcom,spi-qup-v2.2.1";
+			reg = <0x078b9000 0x600>;
+			interrupts = <GIC_SPI 99 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc GCC_BLSP1_AHB_CLK>,
+				 <&gcc GCC_BLSP1_QUP4_SPI_APPS_CLK>;
+			clock-names = "iface", "core";
+			pinctrl-names = "default";
+			pinctrl-0 = <&blsp1_spi4_default>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		blsp2_dma: dma@7ac4000 {
+			compatible = "qcom,bam-v1.7.0";
+			reg = <0x07ac4000 0x17000>;
+			interrupts = <GIC_SPI 239 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc GCC_BLSP2_AHB_CLK>;
+			clock-names = "bam_clk";
+			#dma-cells = <1>;
+			qcom,controlled-remotely = <1>;
+			qcom,ee = <0>;
+			status = "disabled";
+		};
+
+		blsp2_uart0: serial@7aef000 {
+			compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm";
+			reg = <0x07aef000 0x200>;
+			interrupts = <GIC_SPI 297 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc GCC_BLSP2_UART0_APPS_CLK>, <&gcc GCC_BLSP2_AHB_CLK>;
+			clock-names = "core", "iface";
+			dmas = <&blsp2_dma 1>, <&blsp2_dma 0>;
+			dma-names = "rx", "tx";
+			pinctrl-names = "default";
+			pinctrl-0 = <&blsp2_uart0_default>;
+			status = "disabled";
+		};
+
+		blsp2_i2c0: i2c@7af5000 {
+			compatible = "qcom,i2c-qup-v2.2.1";
+			reg = <0x07af5000 0x600>;
+			interrupts = <GIC_SPI 299 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc GCC_BLSP2_AHB_CLK>,
+				 <&gcc GCC_BLSP2_QUP0_I2C_APPS_CLK>;
+			clock-names = "iface", "core";
+			pinctrl-names = "default";
+			pinctrl-0 = <&blsp2_i2c0_default>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		blsp2_spi0: spi@7af5000 {
+			compatible = "qcom,spi-qup-v2.2.1";
+			reg = <0x07af5000 0x600>;
+			interrupts = <GIC_SPI 299 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc GCC_BLSP2_AHB_CLK>,
+				 <&gcc GCC_BLSP2_QUP0_SPI_APPS_CLK>;
+			clock-names = "iface", "core";
+			pinctrl-names = "default";
+			pinctrl-0 = <&blsp2_spi0_default>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
 		intc: interrupt-controller@b000000 {
 			compatible = "qcom,msm-qgic2";
 			interrupt-controller;
diff --git a/arch/arm64/boot/dts/qcom/sdm845-mtp.dts b/arch/arm64/boot/dts/qcom/sdm845-mtp.dts
index b3def0358177..af8c6a2445a2 100644
--- a/arch/arm64/boot/dts/qcom/sdm845-mtp.dts
+++ b/arch/arm64/boot/dts/qcom/sdm845-mtp.dts
@@ -7,6 +7,7 @@
 
 /dts-v1/;
 
+#include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/regulator/qcom,rpmh-regulator.h>
 #include "sdm845.dtsi"
 
@@ -346,7 +347,9 @@
 &gcc {
 	protected-clocks = <GCC_QSPI_CORE_CLK>,
 			   <GCC_QSPI_CORE_CLK_SRC>,
-			   <GCC_QSPI_CNOC_PERIPH_AHB_CLK>;
+			   <GCC_QSPI_CNOC_PERIPH_AHB_CLK>,
+			   <GCC_LPASS_Q6_AXI_CLK>,
+			   <GCC_LPASS_SWAY_CLK>;
 };
 
 &i2c10 {
@@ -358,14 +361,36 @@
 	status = "okay";
 };
 
-&tlmm {
-	gpio-reserved-ranges = <0 4>, <81 4>;
+&sdhc_2 {
+	status = "okay";
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&sdc2_clk &sdc2_cmd &sdc2_data &sd_card_det_n>;
+
+	vmmc-supply = <&vreg_l21a_2p95>;
+	vqmmc-supply = <&vddpx_2>;
+
+	cd-gpios = <&tlmm 126 GPIO_ACTIVE_LOW>;
 };
 
 &uart9 {
 	status = "okay";
 };
 
+&ufs_mem_hc {
+	status = "okay";
+
+	vcc-supply = <&vreg_l20a_2p95>;
+	vcc-max-microamp = <600000>;
+};
+
+&ufs_mem_phy {
+	status = "okay";
+
+	vdda-phy-supply = <&vdda_ufs1_core>;
+	vdda-pll-supply = <&vdda_ufs1_1p2>;
+};
+
 &usb_1 {
 	status = "okay";
 };
@@ -427,6 +452,14 @@
 	vdda-pll-supply = <&vdda_usb2_ss_core>;
 };
 
+&wifi {
+	status = "okay";
+	vdd-0.8-cx-mx-supply = <&vreg_l5a_0p8>;
+	vdd-1.8-xo-supply = <&vreg_l7a_1p8>;
+	vdd-1.3-rfa-supply = <&vreg_l17a_1p3>;
+	vdd-3.3-ch0-supply = <&vreg_l25a_3p3>;
+};
+
 /* PINCTRL - additions to nodes defined in sdm845.dtsi */
 
 &qup_i2c10_default {
@@ -450,3 +483,48 @@
 		bias-pull-up;
 	};
 };
+
+&tlmm {
+	gpio-reserved-ranges = <0 4>, <81 4>;
+
+	sdc2_clk: sdc2-clk {
+		pinconf {
+			pins = "sdc2_clk";
+			bias-disable;
+
+			/*
+			 * It seems that mmc_test reports errors if drive
+			 * strength is not 16 on clk, cmd, and data pins.
+			 */
+			drive-strength = <16>;
+		};
+	};
+
+	sdc2_cmd: sdc2-cmd {
+		pinconf {
+			pins = "sdc2_cmd";
+			bias-pull-up;
+			drive-strength = <16>;
+		};
+	};
+
+	sdc2_data: sdc2-data {
+		pinconf {
+			pins = "sdc2_data";
+			bias-pull-up;
+			drive-strength = <16>;
+		};
+	};
+
+	sd_card_det_n: sd-card-det-n {
+		pinmux {
+			pins = "gpio126";
+			function = "gpio";
+		};
+
+		pinconf {
+			pins = "gpio126";
+			bias-pull-up;
+		};
+	};
+};
diff --git a/arch/arm64/boot/dts/qcom/sdm845.dtsi b/arch/arm64/boot/dts/qcom/sdm845.dtsi
index c27cbd3bcb0a..2194794fe84d 100644
--- a/arch/arm64/boot/dts/qcom/sdm845.dtsi
+++ b/arch/arm64/boot/dts/qcom/sdm845.dtsi
@@ -7,12 +7,16 @@
 
 #include <dt-bindings/clock/qcom,dispcc-sdm845.h>
 #include <dt-bindings/clock/qcom,gcc-sdm845.h>
+#include <dt-bindings/clock/qcom,gpucc-sdm845.h>
+#include <dt-bindings/clock/qcom,lpass-sdm845.h>
 #include <dt-bindings/clock/qcom,rpmh.h>
+#include <dt-bindings/clock/qcom,videocc-sdm845.h>
 #include <dt-bindings/interrupt-controller/arm-gic.h>
 #include <dt-bindings/phy/phy-qcom-qusb2.h>
+#include <dt-bindings/power/qcom-rpmpd.h>
 #include <dt-bindings/reset/qcom,sdm845-aoss.h>
+#include <dt-bindings/reset/qcom,sdm845-pdc.h>
 #include <dt-bindings/soc/qcom,rpmh-rsc.h>
-#include <dt-bindings/clock/qcom,gcc-sdm845.h>
 
 / {
 	interrupt-parent = <&intc>;
@@ -88,6 +92,21 @@
 			reg = <0 0x86200000 0 0x2d00000>;
 			no-map;
 		};
+
+		wlan_msa_mem: memory@96700000 {
+			reg = <0 0x96700000 0 0x100000>;
+			no-map;
+		};
+
+		mpss_region: memory@8e000000 {
+			reg = <0 0x8e000000 0 0x7800000>;
+			no-map;
+		};
+
+		mba_region: memory@96500000 {
+			reg = <0 0x96500000 0 0x200000>;
+			no-map;
+		};
 	};
 
 	cpus {
@@ -99,6 +118,7 @@
 			compatible = "qcom,kryo385";
 			reg = <0x0 0x0>;
 			enable-method = "psci";
+			qcom,freq-domain = <&cpufreq_hw 0>;
 			next-level-cache = <&L2_0>;
 			L2_0: l2-cache {
 				compatible = "cache";
@@ -114,6 +134,7 @@
 			compatible = "qcom,kryo385";
 			reg = <0x0 0x100>;
 			enable-method = "psci";
+			qcom,freq-domain = <&cpufreq_hw 0>;
 			next-level-cache = <&L2_100>;
 			L2_100: l2-cache {
 				compatible = "cache";
@@ -126,6 +147,7 @@
 			compatible = "qcom,kryo385";
 			reg = <0x0 0x200>;
 			enable-method = "psci";
+			qcom,freq-domain = <&cpufreq_hw 0>;
 			next-level-cache = <&L2_200>;
 			L2_200: l2-cache {
 				compatible = "cache";
@@ -138,6 +160,7 @@
 			compatible = "qcom,kryo385";
 			reg = <0x0 0x300>;
 			enable-method = "psci";
+			qcom,freq-domain = <&cpufreq_hw 0>;
 			next-level-cache = <&L2_300>;
 			L2_300: l2-cache {
 				compatible = "cache";
@@ -150,6 +173,7 @@
 			compatible = "qcom,kryo385";
 			reg = <0x0 0x400>;
 			enable-method = "psci";
+			qcom,freq-domain = <&cpufreq_hw 1>;
 			next-level-cache = <&L2_400>;
 			L2_400: l2-cache {
 				compatible = "cache";
@@ -162,6 +186,7 @@
 			compatible = "qcom,kryo385";
 			reg = <0x0 0x500>;
 			enable-method = "psci";
+			qcom,freq-domain = <&cpufreq_hw 1>;
 			next-level-cache = <&L2_500>;
 			L2_500: l2-cache {
 				compatible = "cache";
@@ -174,6 +199,7 @@
 			compatible = "qcom,kryo385";
 			reg = <0x0 0x600>;
 			enable-method = "psci";
+			qcom,freq-domain = <&cpufreq_hw 1>;
 			next-level-cache = <&L2_600>;
 			L2_600: l2-cache {
 				compatible = "cache";
@@ -186,6 +212,7 @@
 			compatible = "qcom,kryo385";
 			reg = <0x0 0x700>;
 			enable-method = "psci";
+			qcom,freq-domain = <&cpufreq_hw 1>;
 			next-level-cache = <&L2_700>;
 			L2_700: l2-cache {
 				compatible = "cache";
@@ -222,6 +249,12 @@
 		};
 	};
 
+	firmware {
+		scm {
+			compatible = "qcom,scm-sdm845", "qcom,scm";
+		};
+	};
+
 	tcsr_mutex: hwlock {
 		compatible = "qcom,tcsr-mutex";
 		syscon = <&tcsr_mutex_regs 0 0x1000>;
@@ -328,14 +361,15 @@
 	};
 
 	soc: soc {
-		#address-cells = <1>;
-		#size-cells = <1>;
-		ranges = <0 0 0 0xffffffff>;
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges = <0 0 0 0 0x10 0>;
+		dma-ranges = <0 0 0 0 0x10 0>;
 		compatible = "simple-bus";
 
 		gcc: clock-controller@100000 {
 			compatible = "qcom,gcc-sdm845";
-			reg = <0x100000 0x1f0000>;
+			reg = <0 0x00100000 0 0x1f0000>;
 			#clock-cells = <1>;
 			#reset-cells = <1>;
 			#power-domain-cells = <1>;
@@ -343,7 +377,7 @@
 
 		qfprom@784000 {
 			compatible = "qcom,qfprom";
-			reg = <0x784000 0x8ff>;
+			reg = <0 0x00784000 0 0x8ff>;
 			#address-cells = <1>;
 			#size-cells = <1>;
 
@@ -360,25 +394,25 @@
 
 		rng: rng@793000 {
 			compatible = "qcom,prng-ee";
-			reg = <0x00793000 0x1000>;
+			reg = <0 0x00793000 0 0x1000>;
 			clocks = <&gcc GCC_PRNG_AHB_CLK>;
 			clock-names = "core";
 		};
 
 		qupv3_id_0: geniqup@8c0000 {
 			compatible = "qcom,geni-se-qup";
-			reg = <0x8c0000 0x6000>;
+			reg = <0 0x008c0000 0 0x6000>;
 			clock-names = "m-ahb", "s-ahb";
 			clocks = <&gcc GCC_QUPV3_WRAP_0_M_AHB_CLK>,
 				 <&gcc GCC_QUPV3_WRAP_0_S_AHB_CLK>;
-			#address-cells = <1>;
-			#size-cells = <1>;
+			#address-cells = <2>;
+			#size-cells = <2>;
 			ranges;
 			status = "disabled";
 
 			i2c0: i2c@880000 {
 				compatible = "qcom,geni-i2c";
-				reg = <0x880000 0x4000>;
+				reg = <0 0x00880000 0 0x4000>;
 				clock-names = "se";
 				clocks = <&gcc GCC_QUPV3_WRAP0_S0_CLK>;
 				pinctrl-names = "default";
@@ -391,7 +425,7 @@
 
 			spi0: spi@880000 {
 				compatible = "qcom,geni-spi";
-				reg = <0x880000 0x4000>;
+				reg = <0 0x00880000 0 0x4000>;
 				clock-names = "se";
 				clocks = <&gcc GCC_QUPV3_WRAP0_S0_CLK>;
 				pinctrl-names = "default";
@@ -404,7 +438,7 @@
 
 			uart0: serial@880000 {
 				compatible = "qcom,geni-uart";
-				reg = <0x880000 0x4000>;
+				reg = <0 0x00880000 0 0x4000>;
 				clock-names = "se";
 				clocks = <&gcc GCC_QUPV3_WRAP0_S0_CLK>;
 				pinctrl-names = "default";
@@ -415,7 +449,7 @@
 
 			i2c1: i2c@884000 {
 				compatible = "qcom,geni-i2c";
-				reg = <0x884000 0x4000>;
+				reg = <0 0x00884000 0 0x4000>;
 				clock-names = "se";
 				clocks = <&gcc GCC_QUPV3_WRAP0_S1_CLK>;
 				pinctrl-names = "default";
@@ -428,7 +462,7 @@
 
 			spi1: spi@884000 {
 				compatible = "qcom,geni-spi";
-				reg = <0x884000 0x4000>;
+				reg = <0 0x00884000 0 0x4000>;
 				clock-names = "se";
 				clocks = <&gcc GCC_QUPV3_WRAP0_S1_CLK>;
 				pinctrl-names = "default";
@@ -441,7 +475,7 @@
 
 			uart1: serial@884000 {
 				compatible = "qcom,geni-uart";
-				reg = <0x884000 0x4000>;
+				reg = <0 0x00884000 0 0x4000>;
 				clock-names = "se";
 				clocks = <&gcc GCC_QUPV3_WRAP0_S1_CLK>;
 				pinctrl-names = "default";
@@ -452,7 +486,7 @@
 
 			i2c2: i2c@888000 {
 				compatible = "qcom,geni-i2c";
-				reg = <0x888000 0x4000>;
+				reg = <0 0x00888000 0 0x4000>;
 				clock-names = "se";
 				clocks = <&gcc GCC_QUPV3_WRAP0_S2_CLK>;
 				pinctrl-names = "default";
@@ -465,7 +499,7 @@
 
 			spi2: spi@888000 {
 				compatible = "qcom,geni-spi";
-				reg = <0x888000 0x4000>;
+				reg = <0 0x00888000 0 0x4000>;
 				clock-names = "se";
 				clocks = <&gcc GCC_QUPV3_WRAP0_S2_CLK>;
 				pinctrl-names = "default";
@@ -478,7 +512,7 @@
 
 			uart2: serial@888000 {
 				compatible = "qcom,geni-uart";
-				reg = <0x888000 0x4000>;
+				reg = <0 0x00888000 0 0x4000>;
 				clock-names = "se";
 				clocks = <&gcc GCC_QUPV3_WRAP0_S2_CLK>;
 				pinctrl-names = "default";
@@ -489,7 +523,7 @@
 
 			i2c3: i2c@88c000 {
 				compatible = "qcom,geni-i2c";
-				reg = <0x88c000 0x4000>;
+				reg = <0 0x0088c000 0 0x4000>;
 				clock-names = "se";
 				clocks = <&gcc GCC_QUPV3_WRAP0_S3_CLK>;
 				pinctrl-names = "default";
@@ -502,7 +536,7 @@
 
 			spi3: spi@88c000 {
 				compatible = "qcom,geni-spi";
-				reg = <0x88c000 0x4000>;
+				reg = <0 0x0088c000 0 0x4000>;
 				clock-names = "se";
 				clocks = <&gcc GCC_QUPV3_WRAP0_S3_CLK>;
 				pinctrl-names = "default";
@@ -515,7 +549,7 @@
 
 			uart3: serial@88c000 {
 				compatible = "qcom,geni-uart";
-				reg = <0x88c000 0x4000>;
+				reg = <0 0x0088c000 0 0x4000>;
 				clock-names = "se";
 				clocks = <&gcc GCC_QUPV3_WRAP0_S3_CLK>;
 				pinctrl-names = "default";
@@ -526,7 +560,7 @@
 
 			i2c4: i2c@890000 {
 				compatible = "qcom,geni-i2c";
-				reg = <0x890000 0x4000>;
+				reg = <0 0x00890000 0 0x4000>;
 				clock-names = "se";
 				clocks = <&gcc GCC_QUPV3_WRAP0_S4_CLK>;
 				pinctrl-names = "default";
@@ -539,7 +573,7 @@
 
 			spi4: spi@890000 {
 				compatible = "qcom,geni-spi";
-				reg = <0x890000 0x4000>;
+				reg = <0 0x00890000 0 0x4000>;
 				clock-names = "se";
 				clocks = <&gcc GCC_QUPV3_WRAP0_S4_CLK>;
 				pinctrl-names = "default";
@@ -552,7 +586,7 @@
 
 			uart4: serial@890000 {
 				compatible = "qcom,geni-uart";
-				reg = <0x890000 0x4000>;
+				reg = <0 0x00890000 0 0x4000>;
 				clock-names = "se";
 				clocks = <&gcc GCC_QUPV3_WRAP0_S4_CLK>;
 				pinctrl-names = "default";
@@ -563,7 +597,7 @@
 
 			i2c5: i2c@894000 {
 				compatible = "qcom,geni-i2c";
-				reg = <0x894000 0x4000>;
+				reg = <0 0x00894000 0 0x4000>;
 				clock-names = "se";
 				clocks = <&gcc GCC_QUPV3_WRAP0_S5_CLK>;
 				pinctrl-names = "default";
@@ -576,7 +610,7 @@
 
 			spi5: spi@894000 {
 				compatible = "qcom,geni-spi";
-				reg = <0x894000 0x4000>;
+				reg = <0 0x00894000 0 0x4000>;
 				clock-names = "se";
 				clocks = <&gcc GCC_QUPV3_WRAP0_S5_CLK>;
 				pinctrl-names = "default";
@@ -589,7 +623,7 @@
 
 			uart5: serial@894000 {
 				compatible = "qcom,geni-uart";
-				reg = <0x894000 0x4000>;
+				reg = <0 0x00894000 0 0x4000>;
 				clock-names = "se";
 				clocks = <&gcc GCC_QUPV3_WRAP0_S5_CLK>;
 				pinctrl-names = "default";
@@ -600,7 +634,7 @@
 
 			i2c6: i2c@898000 {
 				compatible = "qcom,geni-i2c";
-				reg = <0x898000 0x4000>;
+				reg = <0 0x00898000 0 0x4000>;
 				clock-names = "se";
 				clocks = <&gcc GCC_QUPV3_WRAP0_S6_CLK>;
 				pinctrl-names = "default";
@@ -613,7 +647,7 @@
 
 			spi6: spi@898000 {
 				compatible = "qcom,geni-spi";
-				reg = <0x898000 0x4000>;
+				reg = <0 0x00898000 0 0x4000>;
 				clock-names = "se";
 				clocks = <&gcc GCC_QUPV3_WRAP0_S6_CLK>;
 				pinctrl-names = "default";
@@ -626,7 +660,7 @@
 
 			uart6: serial@898000 {
 				compatible = "qcom,geni-uart";
-				reg = <0x898000 0x4000>;
+				reg = <0 0x00898000 0 0x4000>;
 				clock-names = "se";
 				clocks = <&gcc GCC_QUPV3_WRAP0_S6_CLK>;
 				pinctrl-names = "default";
@@ -637,7 +671,7 @@
 
 			i2c7: i2c@89c000 {
 				compatible = "qcom,geni-i2c";
-				reg = <0x89c000 0x4000>;
+				reg = <0 0x0089c000 0 0x4000>;
 				clock-names = "se";
 				clocks = <&gcc GCC_QUPV3_WRAP0_S7_CLK>;
 				pinctrl-names = "default";
@@ -650,7 +684,7 @@
 
 			spi7: spi@89c000 {
 				compatible = "qcom,geni-spi";
-				reg = <0x89c000 0x4000>;
+				reg = <0 0x0089c000 0 0x4000>;
 				clock-names = "se";
 				clocks = <&gcc GCC_QUPV3_WRAP0_S7_CLK>;
 				pinctrl-names = "default";
@@ -663,7 +697,7 @@
 
 			uart7: serial@89c000 {
 				compatible = "qcom,geni-uart";
-				reg = <0x89c000 0x4000>;
+				reg = <0 0x0089c000 0 0x4000>;
 				clock-names = "se";
 				clocks = <&gcc GCC_QUPV3_WRAP0_S7_CLK>;
 				pinctrl-names = "default";
@@ -675,18 +709,18 @@
 
 		qupv3_id_1: geniqup@ac0000 {
 			compatible = "qcom,geni-se-qup";
-			reg = <0xac0000 0x6000>;
+			reg = <0 0x00ac0000 0 0x6000>;
 			clock-names = "m-ahb", "s-ahb";
 			clocks = <&gcc GCC_QUPV3_WRAP_1_M_AHB_CLK>,
 				 <&gcc GCC_QUPV3_WRAP_1_S_AHB_CLK>;
-			#address-cells = <1>;
-			#size-cells = <1>;
+			#address-cells = <2>;
+			#size-cells = <2>;
 			ranges;
 			status = "disabled";
 
 			i2c8: i2c@a80000 {
 				compatible = "qcom,geni-i2c";
-				reg = <0xa80000 0x4000>;
+				reg = <0 0x00a80000 0 0x4000>;
 				clock-names = "se";
 				clocks = <&gcc GCC_QUPV3_WRAP1_S0_CLK>;
 				pinctrl-names = "default";
@@ -699,7 +733,7 @@
 
 			spi8: spi@a80000 {
 				compatible = "qcom,geni-spi";
-				reg = <0xa80000 0x4000>;
+				reg = <0 0x00a80000 0 0x4000>;
 				clock-names = "se";
 				clocks = <&gcc GCC_QUPV3_WRAP1_S0_CLK>;
 				pinctrl-names = "default";
@@ -712,7 +746,7 @@
 
 			uart8: serial@a80000 {
 				compatible = "qcom,geni-uart";
-				reg = <0xa80000 0x4000>;
+				reg = <0 0x00a80000 0 0x4000>;
 				clock-names = "se";
 				clocks = <&gcc GCC_QUPV3_WRAP1_S0_CLK>;
 				pinctrl-names = "default";
@@ -723,7 +757,7 @@
 
 			i2c9: i2c@a84000 {
 				compatible = "qcom,geni-i2c";
-				reg = <0xa84000 0x4000>;
+				reg = <0 0x00a84000 0 0x4000>;
 				clock-names = "se";
 				clocks = <&gcc GCC_QUPV3_WRAP1_S1_CLK>;
 				pinctrl-names = "default";
@@ -736,7 +770,7 @@
 
 			spi9: spi@a84000 {
 				compatible = "qcom,geni-spi";
-				reg = <0xa84000 0x4000>;
+				reg = <0 0x00a84000 0 0x4000>;
 				clock-names = "se";
 				clocks = <&gcc GCC_QUPV3_WRAP1_S1_CLK>;
 				pinctrl-names = "default";
@@ -749,7 +783,7 @@
 
 			uart9: serial@a84000 {
 				compatible = "qcom,geni-debug-uart";
-				reg = <0xa84000 0x4000>;
+				reg = <0 0x00a84000 0 0x4000>;
 				clock-names = "se";
 				clocks = <&gcc GCC_QUPV3_WRAP1_S1_CLK>;
 				pinctrl-names = "default";
@@ -760,7 +794,7 @@
 
 			i2c10: i2c@a88000 {
 				compatible = "qcom,geni-i2c";
-				reg = <0xa88000 0x4000>;
+				reg = <0 0x00a88000 0 0x4000>;
 				clock-names = "se";
 				clocks = <&gcc GCC_QUPV3_WRAP1_S2_CLK>;
 				pinctrl-names = "default";
@@ -773,7 +807,7 @@
 
 			spi10: spi@a88000 {
 				compatible = "qcom,geni-spi";
-				reg = <0xa88000 0x4000>;
+				reg = <0 0x00a88000 0 0x4000>;
 				clock-names = "se";
 				clocks = <&gcc GCC_QUPV3_WRAP1_S2_CLK>;
 				pinctrl-names = "default";
@@ -786,7 +820,7 @@
 
 			uart10: serial@a88000 {
 				compatible = "qcom,geni-uart";
-				reg = <0xa88000 0x4000>;
+				reg = <0 0x00a88000 0 0x4000>;
 				clock-names = "se";
 				clocks = <&gcc GCC_QUPV3_WRAP1_S2_CLK>;
 				pinctrl-names = "default";
@@ -797,7 +831,7 @@
 
 			i2c11: i2c@a8c000 {
 				compatible = "qcom,geni-i2c";
-				reg = <0xa8c000 0x4000>;
+				reg = <0 0x00a8c000 0 0x4000>;
 				clock-names = "se";
 				clocks = <&gcc GCC_QUPV3_WRAP1_S3_CLK>;
 				pinctrl-names = "default";
@@ -810,7 +844,7 @@
 
 			spi11: spi@a8c000 {
 				compatible = "qcom,geni-spi";
-				reg = <0xa8c000 0x4000>;
+				reg = <0 0x00a8c000 0 0x4000>;
 				clock-names = "se";
 				clocks = <&gcc GCC_QUPV3_WRAP1_S3_CLK>;
 				pinctrl-names = "default";
@@ -823,7 +857,7 @@
 
 			uart11: serial@a8c000 {
 				compatible = "qcom,geni-uart";
-				reg = <0xa8c000 0x4000>;
+				reg = <0 0x00a8c000 0 0x4000>;
 				clock-names = "se";
 				clocks = <&gcc GCC_QUPV3_WRAP1_S3_CLK>;
 				pinctrl-names = "default";
@@ -834,7 +868,7 @@
 
 			i2c12: i2c@a90000 {
 				compatible = "qcom,geni-i2c";
-				reg = <0xa90000 0x4000>;
+				reg = <0 0x00a90000 0 0x4000>;
 				clock-names = "se";
 				clocks = <&gcc GCC_QUPV3_WRAP1_S4_CLK>;
 				pinctrl-names = "default";
@@ -847,7 +881,7 @@
 
 			spi12: spi@a90000 {
 				compatible = "qcom,geni-spi";
-				reg = <0xa90000 0x4000>;
+				reg = <0 0x00a90000 0 0x4000>;
 				clock-names = "se";
 				clocks = <&gcc GCC_QUPV3_WRAP1_S4_CLK>;
 				pinctrl-names = "default";
@@ -860,7 +894,7 @@
 
 			uart12: serial@a90000 {
 				compatible = "qcom,geni-uart";
-				reg = <0xa90000 0x4000>;
+				reg = <0 0x00a90000 0 0x4000>;
 				clock-names = "se";
 				clocks = <&gcc GCC_QUPV3_WRAP1_S4_CLK>;
 				pinctrl-names = "default";
@@ -871,7 +905,7 @@
 
 			i2c13: i2c@a94000 {
 				compatible = "qcom,geni-i2c";
-				reg = <0xa94000 0x4000>;
+				reg = <0 0x00a94000 0 0x4000>;
 				clock-names = "se";
 				clocks = <&gcc GCC_QUPV3_WRAP1_S5_CLK>;
 				pinctrl-names = "default";
@@ -884,7 +918,7 @@
 
 			spi13: spi@a94000 {
 				compatible = "qcom,geni-spi";
-				reg = <0xa94000 0x4000>;
+				reg = <0 0x00a94000 0 0x4000>;
 				clock-names = "se";
 				clocks = <&gcc GCC_QUPV3_WRAP1_S5_CLK>;
 				pinctrl-names = "default";
@@ -897,7 +931,7 @@
 
 			uart13: serial@a94000 {
 				compatible = "qcom,geni-uart";
-				reg = <0xa94000 0x4000>;
+				reg = <0 0x00a94000 0 0x4000>;
 				clock-names = "se";
 				clocks = <&gcc GCC_QUPV3_WRAP1_S5_CLK>;
 				pinctrl-names = "default";
@@ -908,7 +942,7 @@
 
 			i2c14: i2c@a98000 {
 				compatible = "qcom,geni-i2c";
-				reg = <0xa98000 0x4000>;
+				reg = <0 0x00a98000 0 0x4000>;
 				clock-names = "se";
 				clocks = <&gcc GCC_QUPV3_WRAP1_S6_CLK>;
 				pinctrl-names = "default";
@@ -921,7 +955,7 @@
 
 			spi14: spi@a98000 {
 				compatible = "qcom,geni-spi";
-				reg = <0xa98000 0x4000>;
+				reg = <0 0x00a98000 0 0x4000>;
 				clock-names = "se";
 				clocks = <&gcc GCC_QUPV3_WRAP1_S6_CLK>;
 				pinctrl-names = "default";
@@ -934,7 +968,7 @@
 
 			uart14: serial@a98000 {
 				compatible = "qcom,geni-uart";
-				reg = <0xa98000 0x4000>;
+				reg = <0 0x00a98000 0 0x4000>;
 				clock-names = "se";
 				clocks = <&gcc GCC_QUPV3_WRAP1_S6_CLK>;
 				pinctrl-names = "default";
@@ -945,7 +979,7 @@
 
 			i2c15: i2c@a9c000 {
 				compatible = "qcom,geni-i2c";
-				reg = <0xa9c000 0x4000>;
+				reg = <0 0x00a9c000 0 0x4000>;
 				clock-names = "se";
 				clocks = <&gcc GCC_QUPV3_WRAP1_S7_CLK>;
 				pinctrl-names = "default";
@@ -958,7 +992,7 @@
 
 			spi15: spi@a9c000 {
 				compatible = "qcom,geni-spi";
-				reg = <0xa9c000 0x4000>;
+				reg = <0 0x00a9c000 0 0x4000>;
 				clock-names = "se";
 				clocks = <&gcc GCC_QUPV3_WRAP1_S7_CLK>;
 				pinctrl-names = "default";
@@ -971,7 +1005,7 @@
 
 			uart15: serial@a9c000 {
 				compatible = "qcom,geni-uart";
-				reg = <0xa9c000 0x4000>;
+				reg = <0 0x00a9c000 0 0x4000>;
 				clock-names = "se";
 				clocks = <&gcc GCC_QUPV3_WRAP1_S7_CLK>;
 				pinctrl-names = "default";
@@ -981,19 +1015,121 @@
 			};
 		};
 
+		ufs_mem_hc: ufshc@1d84000 {
+			compatible = "qcom,sdm845-ufshc", "qcom,ufshc",
+				     "jedec,ufs-2.0";
+			reg = <0 0x01d84000 0 0x2500>;
+			interrupts = <GIC_SPI 265 IRQ_TYPE_LEVEL_HIGH>;
+			phys = <&ufs_mem_phy_lanes>;
+			phy-names = "ufsphy";
+			lanes-per-direction = <2>;
+			power-domains = <&gcc UFS_PHY_GDSC>;
+
+			iommus = <&apps_smmu 0x100 0xf>;
+
+			clock-names =
+				"core_clk",
+				"bus_aggr_clk",
+				"iface_clk",
+				"core_clk_unipro",
+				"ref_clk",
+				"tx_lane0_sync_clk",
+				"rx_lane0_sync_clk",
+				"rx_lane1_sync_clk";
+			clocks =
+				<&gcc GCC_UFS_PHY_AXI_CLK>,
+				<&gcc GCC_AGGRE_UFS_PHY_AXI_CLK>,
+				<&gcc GCC_UFS_PHY_AHB_CLK>,
+				<&gcc GCC_UFS_PHY_UNIPRO_CORE_CLK>,
+				<&rpmhcc RPMH_CXO_CLK>,
+				<&gcc GCC_UFS_PHY_TX_SYMBOL_0_CLK>,
+				<&gcc GCC_UFS_PHY_RX_SYMBOL_0_CLK>,
+				<&gcc GCC_UFS_PHY_RX_SYMBOL_1_CLK>;
+			freq-table-hz =
+				<50000000 200000000>,
+				<0 0>,
+				<0 0>,
+				<37500000 150000000>,
+				<0 0>,
+				<0 0>,
+				<0 0>,
+				<0 0>;
+
+			status = "disabled";
+		};
+
+		ufs_mem_phy: phy@1d87000 {
+			compatible = "qcom,sdm845-qmp-ufs-phy";
+			reg = <0 0x01d87000 0 0x18c>;
+			#address-cells = <2>;
+			#size-cells = <2>;
+			ranges;
+			clock-names = "ref",
+				      "ref_aux";
+			clocks = <&gcc GCC_UFS_MEM_CLKREF_CLK>,
+				 <&gcc GCC_UFS_PHY_PHY_AUX_CLK>;
+
+			status = "disabled";
+
+			ufs_mem_phy_lanes: lanes@1d87400 {
+				reg = <0 0x01d87400 0 0x108>,
+				      <0 0x01d87600 0 0x1e0>,
+				      <0 0x01d87c00 0 0x1dc>,
+				      <0 0x01d87800 0 0x108>,
+				      <0 0x01d87a00 0 0x1e0>;
+				#phy-cells = <0>;
+			};
+		};
+
 		tcsr_mutex_regs: syscon@1f40000 {
 			compatible = "syscon";
-			reg = <0x1f40000 0x40000>;
+			reg = <0 0x01f40000 0 0x40000>;
 		};
 
 		tlmm: pinctrl@3400000 {
 			compatible = "qcom,sdm845-pinctrl";
-			reg = <0x03400000 0xc00000>;
+			reg = <0 0x03400000 0 0xc00000>;
 			interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>;
 			gpio-controller;
 			#gpio-cells = <2>;
 			interrupt-controller;
 			#interrupt-cells = <2>;
+			gpio-ranges = <&tlmm 0 0 150>;
+
+			qspi_clk: qspi-clk {
+				pinmux {
+					pins = "gpio95";
+					function = "qspi_clk";
+				};
+			};
+
+			qspi_cs0: qspi-cs0 {
+				pinmux {
+					pins = "gpio90";
+					function = "qspi_cs";
+				};
+			};
+
+			qspi_cs1: qspi-cs1 {
+				pinmux {
+					pins = "gpio89";
+					function = "qspi_cs";
+				};
+			};
+
+			qspi_data01: qspi-data01 {
+				pinmux-data {
+					pins = "gpio91", "gpio92";
+					function = "qspi_data";
+				};
+			};
+
+			qspi_data12: qspi-data12 {
+				pinmux-data {
+					pins = "gpio93", "gpio94";
+					function = "qspi_data";
+				};
+			};
 
 			qup_i2c0_default: qup-i2c0-default {
 				pinmux {
@@ -1348,9 +1484,46 @@
 			};
 		};
 
+		gpucc: clock-controller@5090000 {
+			compatible = "qcom,sdm845-gpucc";
+			reg = <0 0x05090000 0 0x9000>;
+			#clock-cells = <1>;
+			#reset-cells = <1>;
+			#power-domain-cells = <1>;
+			clocks = <&rpmhcc RPMH_CXO_CLK>;
+			clock-names = "xo";
+		};
+
+		sdhc_2: sdhci@8804000 {
+			compatible = "qcom,sdm845-sdhci", "qcom,sdhci-msm-v5";
+			reg = <0 0x08804000 0 0x1000>;
+
+			interrupts = <GIC_SPI 204 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 222 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "hc_irq", "pwr_irq";
+
+			clocks = <&gcc GCC_SDCC2_AHB_CLK>,
+				 <&gcc GCC_SDCC2_APPS_CLK>;
+			clock-names = "iface", "core";
+
+			status = "disabled";
+		};
+
+		qspi: spi@88df000 {
+			compatible = "qcom,sdm845-qspi", "qcom,qspi-v1";
+			reg = <0 0x088df000 0 0x600>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			interrupts = <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc GCC_QSPI_CNOC_PERIPH_AHB_CLK>,
+				 <&gcc GCC_QSPI_CORE_CLK>;
+			clock-names = "iface", "core";
+			status = "disabled";
+		};
+
 		usb_1_hsphy: phy@88e2000 {
 			compatible = "qcom,sdm845-qusb2-phy";
-			reg = <0x88e2000 0x400>;
+			reg = <0 0x088e2000 0 0x400>;
 			status = "disabled";
 			#phy-cells = <0>;
 
@@ -1365,7 +1538,7 @@
 
 		usb_2_hsphy: phy@88e3000 {
 			compatible = "qcom,sdm845-qusb2-phy";
-			reg = <0x88e3000 0x400>;
+			reg = <0 0x088e3000 0 0x400>;
 			status = "disabled";
 			#phy-cells = <0>;
 
@@ -1380,13 +1553,13 @@
 
 		usb_1_qmpphy: phy@88e9000 {
 			compatible = "qcom,sdm845-qmp-usb3-phy";
-			reg = <0x88e9000 0x18c>,
-			      <0x88e8000 0x10>;
+			reg = <0 0x088e9000 0 0x18c>,
+			      <0 0x088e8000 0 0x10>;
 			reg-names = "reg-base", "dp_com";
 			status = "disabled";
 			#clock-cells = <1>;
-			#address-cells = <1>;
-			#size-cells = <1>;
+			#address-cells = <2>;
+			#size-cells = <2>;
 			ranges;
 
 			clocks = <&gcc GCC_USB3_PRIM_PHY_AUX_CLK>,
@@ -1399,11 +1572,13 @@
 				 <&gcc GCC_USB3_PHY_PRIM_BCR>;
 			reset-names = "phy", "common";
 
-			usb_1_ssphy: lane@88e9200 {
-				reg = <0x88e9200 0x128>,
-				      <0x88e9400 0x200>,
-				      <0x88e9c00 0x218>,
-				      <0x88e9a00 0x100>;
+			usb_1_ssphy: lanes@88e9200 {
+				reg = <0 0x088e9200 0 0x128>,
+				      <0 0x088e9400 0 0x200>,
+				      <0 0x088e9c00 0 0x218>,
+				      <0 0x088e9600 0 0x128>,
+				      <0 0x088e9800 0 0x200>,
+				      <0 0x088e9a00 0 0x100>;
 				#phy-cells = <0>;
 				clocks = <&gcc GCC_USB3_PRIM_PHY_PIPE_CLK>;
 				clock-names = "pipe0";
@@ -1413,11 +1588,11 @@
 
 		usb_2_qmpphy: phy@88eb000 {
 			compatible = "qcom,sdm845-qmp-usb3-uni-phy";
-			reg = <0x88eb000 0x18c>;
+			reg = <0 0x088eb000 0 0x18c>;
 			status = "disabled";
 			#clock-cells = <1>;
-			#address-cells = <1>;
-			#size-cells = <1>;
+			#address-cells = <2>;
+			#size-cells = <2>;
 			ranges;
 
 			clocks = <&gcc GCC_USB3_SEC_PHY_AUX_CLK>,
@@ -1431,10 +1606,10 @@
 			reset-names = "phy", "common";
 
 			usb_2_ssphy: lane@88eb200 {
-				reg = <0x88eb200 0x128>,
-				      <0x88eb400 0x1fc>,
-				      <0x88eb800 0x218>,
-				      <0x88e9600 0x70>;
+				reg = <0 0x088eb200 0 0x128>,
+				      <0 0x088eb400 0 0x1fc>,
+				      <0 0x088eb800 0 0x218>,
+				      <0 0x088eb600 0 0x70>;
 				#phy-cells = <0>;
 				clocks = <&gcc GCC_USB3_SEC_PHY_PIPE_CLK>;
 				clock-names = "pipe0";
@@ -1444,10 +1619,10 @@
 
 		usb_1: usb@a6f8800 {
 			compatible = "qcom,sdm845-dwc3", "qcom,dwc3";
-			reg = <0xa6f8800 0x400>;
+			reg = <0 0x0a6f8800 0 0x400>;
 			status = "disabled";
-			#address-cells = <1>;
-			#size-cells = <1>;
+			#address-cells = <2>;
+			#size-cells = <2>;
 			ranges;
 
 			clocks = <&gcc GCC_CFG_NOC_USB3_PRIM_AXI_CLK>,
@@ -1475,7 +1650,7 @@
 
 			usb_1_dwc3: dwc3@a600000 {
 				compatible = "snps,dwc3";
-				reg = <0xa600000 0xcd00>;
+				reg = <0 0x0a600000 0 0xcd00>;
 				interrupts = <GIC_SPI 133 IRQ_TYPE_LEVEL_HIGH>;
 				snps,dis_u2_susphy_quirk;
 				snps,dis_enblslpm_quirk;
@@ -1486,10 +1661,10 @@
 
 		usb_2: usb@a8f8800 {
 			compatible = "qcom,sdm845-dwc3", "qcom,dwc3";
-			reg = <0xa8f8800 0x400>;
+			reg = <0 0x0a8f8800 0 0x400>;
 			status = "disabled";
-			#address-cells = <1>;
-			#size-cells = <1>;
+			#address-cells = <2>;
+			#size-cells = <2>;
 			ranges;
 
 			clocks = <&gcc GCC_CFG_NOC_USB3_SEC_AXI_CLK>,
@@ -1517,7 +1692,7 @@
 
 			usb_2_dwc3: dwc3@a800000 {
 				compatible = "snps,dwc3";
-				reg = <0xa800000 0xcd00>;
+				reg = <0 0x0a800000 0 0xcd00>;
 				interrupts = <GIC_SPI 138 IRQ_TYPE_LEVEL_HIGH>;
 				snps,dis_u2_susphy_quirk;
 				snps,dis_enblslpm_quirk;
@@ -1526,43 +1701,260 @@
 			};
 		};
 
+		videocc: clock-controller@ab00000 {
+			compatible = "qcom,sdm845-videocc";
+			reg = <0 0x0ab00000 0 0x10000>;
+			#clock-cells = <1>;
+			#power-domain-cells = <1>;
+			#reset-cells = <1>;
+		};
+
+		mdss: mdss@ae00000 {
+			compatible = "qcom,sdm845-mdss";
+			reg = <0 0x0ae00000 0 0x1000>;
+			reg-names = "mdss";
+
+			power-domains = <&dispcc MDSS_GDSC>;
+
+			clocks = <&gcc GCC_DISP_AHB_CLK>,
+				 <&gcc GCC_DISP_AXI_CLK>,
+				 <&dispcc DISP_CC_MDSS_MDP_CLK>;
+			clock-names = "iface", "bus", "core";
+
+			assigned-clocks = <&dispcc DISP_CC_MDSS_MDP_CLK>;
+			assigned-clock-rates = <300000000>;
+
+			interrupts = <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-controller;
+			#interrupt-cells = <1>;
+
+			iommus = <&apps_smmu 0x880 0x8>,
+			         <&apps_smmu 0xc80 0x8>;
+
+			status = "disabled";
+
+			#address-cells = <2>;
+			#size-cells = <2>;
+			ranges;
+
+			mdss_mdp: mdp@ae01000 {
+				compatible = "qcom,sdm845-dpu";
+				reg = <0 0x0ae01000 0 0x8f000>,
+				      <0 0x0aeb0000 0 0x2008>;
+				reg-names = "mdp", "vbif";
+
+				clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>,
+					 <&dispcc DISP_CC_MDSS_AXI_CLK>,
+					 <&dispcc DISP_CC_MDSS_MDP_CLK>,
+					 <&dispcc DISP_CC_MDSS_VSYNC_CLK>;
+				clock-names = "iface", "bus", "core", "vsync";
+
+				assigned-clocks = <&dispcc DISP_CC_MDSS_MDP_CLK>,
+						  <&dispcc DISP_CC_MDSS_VSYNC_CLK>;
+				assigned-clock-rates = <300000000>,
+						       <19200000>;
+
+				interrupt-parent = <&mdss>;
+				interrupts = <0 IRQ_TYPE_LEVEL_HIGH>;
+
+				status = "disabled";
+
+				ports {
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					port@0 {
+						reg = <0>;
+						dpu_intf1_out: endpoint {
+							remote-endpoint = <&dsi0_in>;
+						};
+					};
+
+					port@1 {
+						reg = <1>;
+						dpu_intf2_out: endpoint {
+							remote-endpoint = <&dsi1_in>;
+						};
+					};
+				};
+			};
+
+			dsi0: dsi@ae94000 {
+				compatible = "qcom,mdss-dsi-ctrl";
+				reg = <0 0x0ae94000 0 0x400>;
+				reg-names = "dsi_ctrl";
+
+				interrupt-parent = <&mdss>;
+				interrupts = <4 IRQ_TYPE_LEVEL_HIGH>;
+
+				clocks = <&dispcc DISP_CC_MDSS_BYTE0_CLK>,
+					 <&dispcc DISP_CC_MDSS_BYTE0_INTF_CLK>,
+					 <&dispcc DISP_CC_MDSS_PCLK0_CLK>,
+					 <&dispcc DISP_CC_MDSS_ESC0_CLK>,
+					 <&dispcc DISP_CC_MDSS_AHB_CLK>,
+					 <&dispcc DISP_CC_MDSS_AXI_CLK>;
+				clock-names = "byte",
+					      "byte_intf",
+					      "pixel",
+					      "core",
+					      "iface",
+					      "bus";
+
+				phys = <&dsi0_phy>;
+				phy-names = "dsi";
+
+				status = "disabled";
+
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				ports {
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					port@0 {
+						reg = <0>;
+						dsi0_in: endpoint {
+							remote-endpoint = <&dpu_intf1_out>;
+						};
+					};
+
+					port@1 {
+						reg = <1>;
+						dsi0_out: endpoint {
+						};
+					};
+				};
+			};
+
+			dsi0_phy: dsi-phy@ae94400 {
+				compatible = "qcom,dsi-phy-10nm";
+				reg = <0 0x0ae94400 0 0x200>,
+				      <0 0x0ae94600 0 0x280>,
+				      <0 0x0ae94a00 0 0x1e0>;
+				reg-names = "dsi_phy",
+					    "dsi_phy_lane",
+					    "dsi_pll";
+
+				#clock-cells = <1>;
+				#phy-cells = <0>;
+
+				clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>;
+				clock-names = "iface";
+
+				status = "disabled";
+			};
+
+			dsi1: dsi@ae96000 {
+				compatible = "qcom,mdss-dsi-ctrl";
+				reg = <0 0x0ae96000 0 0x400>;
+				reg-names = "dsi_ctrl";
+
+				interrupt-parent = <&mdss>;
+				interrupts = <5 IRQ_TYPE_LEVEL_HIGH>;
+
+				clocks = <&dispcc DISP_CC_MDSS_BYTE1_CLK>,
+					 <&dispcc DISP_CC_MDSS_BYTE1_INTF_CLK>,
+					 <&dispcc DISP_CC_MDSS_PCLK1_CLK>,
+					 <&dispcc DISP_CC_MDSS_ESC1_CLK>,
+					 <&dispcc DISP_CC_MDSS_AHB_CLK>,
+					 <&dispcc DISP_CC_MDSS_AXI_CLK>;
+				clock-names = "byte",
+					      "byte_intf",
+					      "pixel",
+					      "core",
+					      "iface",
+					      "bus";
+
+				phys = <&dsi1_phy>;
+				phy-names = "dsi";
+
+				status = "disabled";
+
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				ports {
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					port@0 {
+						reg = <0>;
+						dsi1_in: endpoint {
+							remote-endpoint = <&dpu_intf2_out>;
+						};
+					};
+
+					port@1 {
+						reg = <1>;
+						dsi1_out: endpoint {
+						};
+					};
+				};
+			};
+
+			dsi1_phy: dsi-phy@ae96400 {
+				compatible = "qcom,dsi-phy-10nm";
+				reg = <0 0x0ae96400 0 0x200>,
+				      <0 0x0ae96600 0 0x280>,
+				      <0 0x0ae96a00 0 0x10e>;
+				reg-names = "dsi_phy",
+					    "dsi_phy_lane",
+					    "dsi_pll";
+
+				#clock-cells = <1>;
+				#phy-cells = <0>;
+
+				clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>;
+				clock-names = "iface";
+
+				status = "disabled";
+			};
+		};
+
 		dispcc: clock-controller@af00000 {
 			compatible = "qcom,sdm845-dispcc";
-			reg = <0xaf00000 0x10000>;
+			reg = <0 0x0af00000 0 0x10000>;
 			#clock-cells = <1>;
 			#reset-cells = <1>;
 			#power-domain-cells = <1>;
 		};
 
+		pdc_reset: reset-controller@b2e0000 {
+			compatible = "qcom,sdm845-pdc-global";
+			reg = <0 0x0b2e0000 0 0x20000>;
+			#reset-cells = <1>;
+		};
+
 		tsens0: thermal-sensor@c263000 {
 			compatible = "qcom,sdm845-tsens", "qcom,tsens-v2";
-			reg = <0xc263000 0x1ff>, /* TM */
-			      <0xc222000 0x1ff>; /* SROT */
+			reg = <0 0x0c263000 0 0x1ff>, /* TM */
+			      <0 0x0c222000 0 0x1ff>; /* SROT */
 			#qcom,sensors = <13>;
 			#thermal-sensor-cells = <1>;
 		};
 
 		tsens1: thermal-sensor@c265000 {
 			compatible = "qcom,sdm845-tsens", "qcom,tsens-v2";
-			reg = <0xc265000 0x1ff>, /* TM */
-			      <0xc223000 0x1ff>; /* SROT */
+			reg = <0 0x0c265000 0 0x1ff>, /* TM */
+			      <0 0x0c223000 0 0x1ff>; /* SROT */
 			#qcom,sensors = <8>;
 			#thermal-sensor-cells = <1>;
 		};
 
 		aoss_reset: reset-controller@c2a0000 {
 			compatible = "qcom,sdm845-aoss-cc";
-			reg = <0xc2a0000 0x31000>;
+			reg = <0 0x0c2a0000 0 0x31000>;
 			#reset-cells = <1>;
 		};
 
 		spmi_bus: spmi@c440000 {
 			compatible = "qcom,spmi-pmic-arb";
-			reg = <0xc440000 0x1100>,
-			      <0xc600000 0x2000000>,
-			      <0xe600000 0x100000>,
-			      <0xe700000 0xa0000>,
-			      <0xc40a000 0x26000>;
+			reg = <0 0x0c440000 0 0x1100>,
+			      <0 0x0c600000 0 0x2000000>,
+			      <0 0x0e600000 0 0x100000>,
+			      <0 0x0e700000 0 0xa0000>,
+			      <0 0x0c40a000 0 0x26000>;
 			reg-names = "core", "chnls", "obsrvr", "intr", "cnfg";
 			interrupt-names = "periph_irq";
 			interrupts = <GIC_SPI 481 IRQ_TYPE_LEVEL_HIGH>;
@@ -1575,18 +1967,98 @@
 			cell-index = <0>;
 		};
 
+		apps_smmu: iommu@15000000 {
+			compatible = "qcom,sdm845-smmu-500", "arm,mmu-500";
+			reg = <0 0x15000000 0 0x80000>;
+			#iommu-cells = <2>;
+			#global-interrupts = <1>;
+			interrupts = <GIC_SPI 65 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 99 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 104 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 105 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 106 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 107 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 109 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 111 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 112 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 114 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 115 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 116 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 117 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 118 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 181 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 182 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 183 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 184 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 185 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 186 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 187 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 188 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 189 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 190 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 191 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 192 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 315 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 316 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 317 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 318 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 319 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 320 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 321 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 322 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 323 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 324 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 325 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 326 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 327 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 328 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 329 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 330 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 331 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 332 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 333 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 334 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 335 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 336 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 337 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 338 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 339 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 340 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 341 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 342 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 343 IRQ_TYPE_LEVEL_HIGH>;
+		};
+
+		lpasscc: clock-controller@17014000 {
+			compatible = "qcom,sdm845-lpasscc";
+			reg = <0 0x17014000 0 0x1f004>, <0 0x17300000 0 0x200>;
+			reg-names = "cc", "qdsp6ss";
+			#clock-cells = <1>;
+			status = "disabled";
+		};
+
 		apss_shared: mailbox@17990000 {
 			compatible = "qcom,sdm845-apss-shared";
-			reg = <0x17990000 0x1000>;
+			reg = <0 0x17990000 0 0x1000>;
 			#mbox-cells = <1>;
 		};
 
 		apps_rsc: rsc@179c0000 {
 			label = "apps_rsc";
 			compatible = "qcom,rpmh-rsc";
-			reg = <0x179c0000 0x10000>,
-			      <0x179d0000 0x10000>,
-			      <0x179e0000 0x10000>;
+			reg = <0 0x179c0000 0 0x10000>,
+			      <0 0x179d0000 0 0x10000>,
+			      <0 0x179e0000 0 0x10000>;
 			reg-names = "drv-0", "drv-1", "drv-2";
 			interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>,
 				     <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>,
@@ -1602,85 +2074,172 @@
 				compatible = "qcom,sdm845-rpmh-clk";
 				#clock-cells = <1>;
 			};
+
+			rpmhpd: power-controller {
+				compatible = "qcom,sdm845-rpmhpd";
+				#power-domain-cells = <1>;
+				operating-points-v2 = <&rpmhpd_opp_table>;
+
+				rpmhpd_opp_table: opp-table {
+					compatible = "operating-points-v2";
+
+					rpmhpd_opp_ret: opp1 {
+						opp-level = <RPMH_REGULATOR_LEVEL_RETENTION>;
+					};
+
+					rpmhpd_opp_min_svs: opp2 {
+						opp-level = <RPMH_REGULATOR_LEVEL_MIN_SVS>;
+					};
+
+					rpmhpd_opp_low_svs: opp3 {
+						opp-level = <RPMH_REGULATOR_LEVEL_LOW_SVS>;
+					};
+
+					rpmhpd_opp_svs: opp4 {
+						opp-level = <RPMH_REGULATOR_LEVEL_SVS>;
+					};
+
+					rpmhpd_opp_svs_l1: opp5 {
+						opp-level = <RPMH_REGULATOR_LEVEL_SVS_L1>;
+					};
+
+					rpmhpd_opp_nom: opp6 {
+						opp-level = <RPMH_REGULATOR_LEVEL_NOM>;
+					};
+
+					rpmhpd_opp_nom_l1: opp7 {
+						opp-level = <RPMH_REGULATOR_LEVEL_NOM_L1>;
+					};
+
+					rpmhpd_opp_nom_l2: opp8 {
+						opp-level = <RPMH_REGULATOR_LEVEL_NOM_L2>;
+					};
+
+					rpmhpd_opp_turbo: opp9 {
+						opp-level = <RPMH_REGULATOR_LEVEL_TURBO>;
+					};
+
+					rpmhpd_opp_turbo_l1: opp10 {
+						opp-level = <RPMH_REGULATOR_LEVEL_TURBO_L1>;
+					};
+				};
+			};
+
+			rsc_hlos: interconnect {
+				compatible = "qcom,sdm845-rsc-hlos";
+				#interconnect-cells = <1>;
+			};
 		};
 
 		intc: interrupt-controller@17a00000 {
 			compatible = "arm,gic-v3";
-			#address-cells = <1>;
-			#size-cells = <1>;
+			#address-cells = <2>;
+			#size-cells = <2>;
 			ranges;
 			#interrupt-cells = <3>;
 			interrupt-controller;
-			reg = <0x17a00000 0x10000>,     /* GICD */
-			      <0x17a60000 0x100000>;    /* GICR * 8 */
+			reg = <0 0x17a00000 0 0x10000>,     /* GICD */
+			      <0 0x17a60000 0 0x100000>;    /* GICR * 8 */
 			interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH>;
 
 			gic-its@17a40000 {
 				compatible = "arm,gic-v3-its";
 				msi-controller;
 				#msi-cells = <1>;
-				reg = <0x17a40000 0x20000>;
+				reg = <0 0x17a40000 0 0x20000>;
 				status = "disabled";
 			};
 		};
 
 		timer@17c90000 {
-			#address-cells = <1>;
-			#size-cells = <1>;
+			#address-cells = <2>;
+			#size-cells = <2>;
 			ranges;
 			compatible = "arm,armv7-timer-mem";
-			reg = <0x17c90000 0x1000>;
+			reg = <0 0x17c90000 0 0x1000>;
 
 			frame@17ca0000 {
 				frame-number = <0>;
 				interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>,
 					     <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>;
-				reg = <0x17ca0000 0x1000>,
-				      <0x17cb0000 0x1000>;
+				reg = <0 0x17ca0000 0 0x1000>,
+				      <0 0x17cb0000 0 0x1000>;
 			};
 
 			frame@17cc0000 {
 				frame-number = <1>;
 				interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>;
-				reg = <0x17cc0000 0x1000>;
+				reg = <0 0x17cc0000 0 0x1000>;
 				status = "disabled";
 			};
 
 			frame@17cd0000 {
 				frame-number = <2>;
 				interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>;
-				reg = <0x17cd0000 0x1000>;
+				reg = <0 0x17cd0000 0 0x1000>;
 				status = "disabled";
 			};
 
 			frame@17ce0000 {
 				frame-number = <3>;
 				interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>;
-				reg = <0x17ce0000 0x1000>;
+				reg = <0 0x17ce0000 0 0x1000>;
 				status = "disabled";
 			};
 
 			frame@17cf0000 {
 				frame-number = <4>;
 				interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>;
-				reg = <0x17cf0000 0x1000>;
+				reg = <0 0x17cf0000 0 0x1000>;
 				status = "disabled";
 			};
 
 			frame@17d00000 {
 				frame-number = <5>;
 				interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>;
-				reg = <0x17d00000 0x1000>;
+				reg = <0 0x17d00000 0 0x1000>;
 				status = "disabled";
 			};
 
 			frame@17d10000 {
 				frame-number = <6>;
 				interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>;
-				reg = <0x17d10000 0x1000>;
+				reg = <0 0x17d10000 0 0x1000>;
 				status = "disabled";
 			};
 		};
+
+		cpufreq_hw: cpufreq@17d43000 {
+			compatible = "qcom,cpufreq-hw";
+			reg = <0 0x17d43000 0 0x1400>, <0 0x17d45800 0 0x1400>;
+			reg-names = "freq-domain0", "freq-domain1";
+
+			clocks = <&rpmhcc RPMH_CXO_CLK>, <&gcc GPLL0>;
+			clock-names = "xo", "alternate";
+
+			#freq-domain-cells = <1>;
+		};
+
+		wifi: wifi@18800000 {
+			compatible = "qcom,wcn3990-wifi";
+			status = "disabled";
+			reg = <0 0x18800000 0 0x800000>;
+			reg-names = "membase";
+			memory-region = <&wlan_msa_mem>;
+			interrupts =
+				<GIC_SPI 414 IRQ_TYPE_LEVEL_HIGH>,
+				<GIC_SPI 415 IRQ_TYPE_LEVEL_HIGH>,
+				<GIC_SPI 416 IRQ_TYPE_LEVEL_HIGH>,
+				<GIC_SPI 417 IRQ_TYPE_LEVEL_HIGH>,
+				<GIC_SPI 418 IRQ_TYPE_LEVEL_HIGH>,
+				<GIC_SPI 419 IRQ_TYPE_LEVEL_HIGH>,
+				<GIC_SPI 420 IRQ_TYPE_LEVEL_HIGH>,
+				<GIC_SPI 421 IRQ_TYPE_LEVEL_HIGH>,
+				<GIC_SPI 422 IRQ_TYPE_LEVEL_HIGH>,
+				<GIC_SPI 423 IRQ_TYPE_LEVEL_HIGH>,
+				<GIC_SPI 424 IRQ_TYPE_LEVEL_HIGH>,
+				<GIC_SPI 425 IRQ_TYPE_LEVEL_HIGH>;
+		};
 	};
 
 	thermal-zones {