Merge branch 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6

Conflicts:

	drivers/isdn/i4l/isdn_net.c
	fs/cifs/connect.c

Documentation/00-INDEX

@@ -42,14 +42,8 @@ IRQ.txt
 	- description of what an IRQ is.
 ManagementStyle
 	- how to (attempt to) manage kernel hackers.
-MSI-HOWTO.txt
-	- the Message Signaled Interrupts (MSI) Driver Guide HOWTO and FAQ.
 RCU/
 	- directory with info on RCU (read-copy update).
-README.DAC960
-	- info on Mylex DAC960/DAC1100 PCI RAID Controller Driver for Linux.
-README.cycladesZ
-	- info on Cyclades-Z firmware loading.
 SAK.txt
 	- info on Secure Attention Keys.
 SM501.txt
@@ -86,20 +80,16 @@ blackfin/
 	- directory with documentation for the Blackfin arch.
 block/
 	- info on the Block I/O (BIO) layer.
+blockdev/
+	- info on block devices & drivers
 cachetlb.txt
 	- describes the cache/TLB flushing interfaces Linux uses.
-cciss.txt
-	- info, major/minor #'s for Compaq's SMART Array Controllers.
 cdrom/
 	- directory with information on the CD-ROM drivers that Linux has.
-computone.txt
-	- info on Computone Intelliport II/Plus Multiport Serial Driver.
 connector/
 	- docs on the netlink based userspace<->kernel space communication mod.
 console/
 	- documentation on Linux console drivers.
-cpqarray.txt
-	- info on using Compaq's SMART2 Intelligent Disk Array Controllers.
 cpu-freq/
 	- info on CPU frequency and voltage scaling.
 cpu-hotplug.txt
@@ -126,8 +116,6 @@ device-mapper/
 	- directory with info on Device Mapper.
 devices.txt
 	- plain ASCII listing of all the nodes in /dev/ with major minor #'s.
-digiepca.txt
-	- info on Digi Intl. {PC,PCI,EISA}Xx and Xem series cards.
 dontdiff
 	- file containing a list of files that should never be diff'ed.
 driver-model/
@@ -152,14 +140,10 @@ filesystems/
 	- info on the vfs and the various filesystems that Linux supports.
 firmware_class/
 	- request_firmware() hotplug interface info.
-floppy.txt
-	- notes and driver options for the floppy disk driver.
 frv/
 	- Fujitsu FR-V Linux documentation.
 gpio.txt
 	- overview of GPIO (General Purpose Input/Output) access conventions.
-hayes-esp.txt
-	- info on using the Hayes ESP serial driver.
 highuid.txt
 	- notes on the change from 16 bit to 32 bit user/group IDs.
 timers/
@@ -186,8 +170,6 @@ io_ordering.txt
 	- info on ordering I/O writes to memory-mapped addresses.
 ioctl/
 	- directory with documents describing various IOCTL calls.
-ioctl-number.txt
-	- how to implement and register device/driver ioctl calls.
 iostats.txt
 	- info on I/O statistics Linux kernel provides.
 irqflags-tracing.txt
@@ -250,14 +232,10 @@ mips/
 	- directory with info about Linux on MIPS architecture.
 mono.txt
 	- how to execute Mono-based .NET binaries with the help of BINFMT_MISC.
-moxa-smartio
-	- file with info on installing/using Moxa multiport serial driver.
 mutex-design.txt
 	- info on the generic mutex subsystem.
 namespaces/
 	- directory with various information about namespaces
-nbd.txt
-	- info on a TCP implementation of a network block device.
 netlabel/
 	- directory with information on the NetLabel subsystem.
 networking/
@@ -270,8 +248,6 @@ numastat.txt
 	- info on how to read Numa policy hit/miss statistics in sysfs.
 oops-tracing.txt
 	- how to decode those nasty internal kernel error dump messages.
-paride.txt
-	- information about the parallel port IDE subsystem.
 parisc/
 	- directory with info on using Linux on PA-RISC architecture.
 parport.txt
@@ -290,20 +266,16 @@ powerpc/
 	- directory with info on using Linux with the PowerPC.
 preempt-locking.txt
 	- info on locking under a preemptive kernel.
+printk-formats.txt
+	- how to get printk format specifiers right
 prio_tree.txt
 	- info on radix-priority-search-tree use for indexing vmas.
-ramdisk.txt
-	- short guide on how to set up and use the RAM disk.
 rbtree.txt
 	- info on what red-black trees are and what they are for.
-riscom8.txt
-	- notes on using the RISCom/8 multi-port serial driver.
 robust-futex-ABI.txt
 	- documentation of the robust futex ABI.
 robust-futexes.txt
 	- a description of what robust futexes are.
-rocket.txt
-	- info on the Comtrol RocketPort multiport serial driver.
 rt-mutex-design.txt
 	- description of the RealTime mutex implementation design.
 rt-mutex.txt
@@ -332,8 +304,6 @@ sparc/
 	- directory with info on using Linux on Sparc architecture.
 sparse.txt
 	- info on how to obtain and use the sparse tool for typechecking.
-specialix.txt
-	- info on hardware/driver for specialix IO8+ multiport serial card.
 spi/
 	- overview of Linux kernel Serial Peripheral Interface (SPI) support.
 spinlocks.txt
@@ -342,14 +312,10 @@ stable_api_nonsense.txt
 	- info on why the kernel does not have a stable in-kernel api or abi.
 stable_kernel_rules.txt
 	- rules and procedures for the -stable kernel releases.
-stallion.txt
-	- info on using the Stallion multiport serial driver.
 svga.txt
 	- short guide on selecting video modes at boot via VGA BIOS.
 sysfs-rules.txt
 	- How not to use sysfs.
-sx.txt
-	- info on the Specialix SX/SI multiport serial driver.
 sysctl/
 	- directory with info on the /proc/sys/* files.
 sysrq.txt
@@ -358,8 +324,6 @@ telephony/
 	- directory with info on telephony (e.g. voice over IP) support.
 time_interpolators.txt
 	- info on time interpolators.
-tty.txt
-	- guide to the locking policies of the tty layer.
 uml/
 	- directory with information about User Mode Linux.
 unicode.txt

Documentation/ABI/testing/sysfs-c2port

@@ -0,0 +1,88 @@
+What:		/sys/class/c2port/
+Date:		October 2008
+Contact:	Rodolfo Giometti <giometti@linux.it>
+Description:
+		The /sys/class/c2port/ directory will contain files and
+		directories that will provide a unified interface to
+		the C2 port interface.
+
+What:		/sys/class/c2port/c2portX
+Date:		October 2008
+Contact:	Rodolfo Giometti <giometti@linux.it>
+Description:
+		The /sys/class/c2port/c2portX/ directory is related to X-th
+		C2 port into the system. Each directory will contain files to
+		manage and control its C2 port.
+
+What:		/sys/class/c2port/c2portX/access
+Date:		October 2008
+Contact:	Rodolfo Giometti <giometti@linux.it>
+Description:
+		The /sys/class/c2port/c2portX/access file enable the access
+		to the C2 port from the system. No commands can be sent
+		till this entry is set to 0.
+
+What:		/sys/class/c2port/c2portX/dev_id
+Date:		October 2008
+Contact:	Rodolfo Giometti <giometti@linux.it>
+Description:
+		The /sys/class/c2port/c2portX/dev_id file show the device ID
+		of the connected micro.
+
+What:		/sys/class/c2port/c2portX/flash_access
+Date:		October 2008
+Contact:	Rodolfo Giometti <giometti@linux.it>
+Description:
+		The /sys/class/c2port/c2portX/flash_access file enable the
+		access to the on-board flash of the connected micro.
+		No commands can be sent till this entry is set to 0.
+
+What:		/sys/class/c2port/c2portX/flash_block_size
+Date:		October 2008
+Contact:	Rodolfo Giometti <giometti@linux.it>
+Description:
+		The /sys/class/c2port/c2portX/flash_block_size file show
+		the on-board flash block size of the connected micro.
+
+What:		/sys/class/c2port/c2portX/flash_blocks_num
+Date:		October 2008
+Contact:	Rodolfo Giometti <giometti@linux.it>
+Description:
+		The /sys/class/c2port/c2portX/flash_blocks_num file show
+		the on-board flash blocks number of the connected micro.
+
+What:		/sys/class/c2port/c2portX/flash_data
+Date:		October 2008
+Contact:	Rodolfo Giometti <giometti@linux.it>
+Description:
+		The /sys/class/c2port/c2portX/flash_data file export
+		the content of the on-board flash of the connected micro.
+
+What:		/sys/class/c2port/c2portX/flash_erase
+Date:		October 2008
+Contact:	Rodolfo Giometti <giometti@linux.it>
+Description:
+		The /sys/class/c2port/c2portX/flash_erase file execute
+		the "erase" command on the on-board flash of the connected
+		micro.
+
+What:		/sys/class/c2port/c2portX/flash_erase
+Date:		October 2008
+Contact:	Rodolfo Giometti <giometti@linux.it>
+Description:
+		The /sys/class/c2port/c2portX/flash_erase file show the
+		on-board flash size of the connected micro.
+
+What:		/sys/class/c2port/c2portX/reset
+Date:		October 2008
+Contact:	Rodolfo Giometti <giometti@linux.it>
+Description:
+		The /sys/class/c2port/c2portX/reset file execute a "reset"
+		command on the connected micro.
+
+What:		/sys/class/c2port/c2portX/rev_id
+Date:		October 2008
+Contact:	Rodolfo Giometti <giometti@linux.it>
+Description:
+		The /sys/class/c2port/c2portX/rev_id file show the revision ID
+		of the connected micro.

Documentation/ABI/testing/sysfs-firmware-acpi

@@ -89,7 +89,7 @@ Description:
 
 		error - an interrupt that can't be accounted for above.
 
-		invalid: it's either a wakeup GPE or a GPE/Fixed Event that
+		invalid: it's either a GPE or a Fixed Event that
 			doesn't have an event handler.
 
 		disable: the GPE/Fixed Event is valid but disabled.
@@ -117,30 +117,30 @@ Description:
 		and other user space applications so that the machine won't shutdown
 		when pressing the power button.
 		# cat ff_pwr_btn
-		0
+		0	enabled
 		# press the power button for 3 times;
 		# cat ff_pwr_btn
-		3
+		3	enabled
 		# echo disable > ff_pwr_btn
 		# cat ff_pwr_btn
-		disable
+		3	disabled
 		# press the power button for 3 times;
 		# cat ff_pwr_btn
-		disable
+		3	disabled
 		# echo enable > ff_pwr_btn
 		# cat ff_pwr_btn
-		4
+		4	enabled
 		/*
 		 * this is because the status bit is set even if the enable bit is cleared,
 		 * and it triggers an ACPI fixed event when the enable bit is set again
 		 */
 		# press the power button for 3 times;
 		# cat ff_pwr_btn
-		7
+		7	enabled
 		# echo disable > ff_pwr_btn
 		# press the power button for 3 times;
 		# echo clear > ff_pwr_btn	/* clear the status bit */
 		# echo disable > ff_pwr_btn
 		# cat ff_pwr_btn
-		7
+		7	enabled
 

Documentation/PCI/00-INDEX

@@ -1,5 +1,7 @@
 00-INDEX
 	- this file
+MSI-HOWTO.txt
+	- the Message Signaled Interrupts (MSI) Driver Guide HOWTO and FAQ.
 PCI-DMA-mapping.txt
 	- info for PCI drivers using DMA portably across all platforms
 PCIEBUS-HOWTO.txt

Documentation/acpi/debug.txt

@@ -0,0 +1,148 @@
+			ACPI Debug Output
+
+
+The ACPI CA, the Linux ACPI core, and some ACPI drivers can generate debug
+output.  This document describes how to use this facility.
+
+Compile-time configuration
+--------------------------
+
+ACPI debug output is globally enabled by CONFIG_ACPI_DEBUG.  If this config
+option is turned off, the debug messages are not even built into the
+kernel.
+
+Boot- and run-time configuration
+--------------------------------
+
+When CONFIG_ACPI_DEBUG=y, you can select the component and level of messages
+you're interested in.  At boot-time, use the acpi.debug_layer and
+acpi.debug_level kernel command line options.  After boot, you can use the
+debug_layer and debug_level files in /sys/module/acpi/parameters/ to control
+the debug messages.
+
+debug_layer (component)
+-----------------------
+
+The "debug_layer" is a mask that selects components of interest, e.g., a
+specific driver or part of the ACPI interpreter.  To build the debug_layer
+bitmask, look for the "#define _COMPONENT" in an ACPI source file.
+
+You can set the debug_layer mask at boot-time using the acpi.debug_layer
+command line argument, and you can change it after boot by writing values
+to /sys/module/acpi/parameters/debug_layer.
+
+The possible components are defined in include/acpi/acoutput.h and
+include/acpi/acpi_drivers.h.  Reading /sys/module/acpi/parameters/debug_layer
+shows the supported mask values, currently these:
+
+    ACPI_UTILITIES                  0x00000001
+    ACPI_HARDWARE                   0x00000002
+    ACPI_EVENTS                     0x00000004
+    ACPI_TABLES                     0x00000008
+    ACPI_NAMESPACE                  0x00000010
+    ACPI_PARSER                     0x00000020
+    ACPI_DISPATCHER                 0x00000040
+    ACPI_EXECUTER                   0x00000080
+    ACPI_RESOURCES                  0x00000100
+    ACPI_CA_DEBUGGER                0x00000200
+    ACPI_OS_SERVICES                0x00000400
+    ACPI_CA_DISASSEMBLER            0x00000800
+    ACPI_COMPILER                   0x00001000
+    ACPI_TOOLS                      0x00002000
+    ACPI_BUS_COMPONENT              0x00010000
+    ACPI_AC_COMPONENT               0x00020000
+    ACPI_BATTERY_COMPONENT          0x00040000
+    ACPI_BUTTON_COMPONENT           0x00080000
+    ACPI_SBS_COMPONENT              0x00100000
+    ACPI_FAN_COMPONENT              0x00200000
+    ACPI_PCI_COMPONENT              0x00400000
+    ACPI_POWER_COMPONENT            0x00800000
+    ACPI_CONTAINER_COMPONENT        0x01000000
+    ACPI_SYSTEM_COMPONENT           0x02000000
+    ACPI_THERMAL_COMPONENT          0x04000000
+    ACPI_MEMORY_DEVICE_COMPONENT    0x08000000
+    ACPI_VIDEO_COMPONENT            0x10000000
+    ACPI_PROCESSOR_COMPONENT        0x20000000
+
+debug_level
+-----------
+
+The "debug_level" is a mask that selects different types of messages, e.g.,
+those related to initialization, method execution, informational messages, etc.
+To build debug_level, look at the level specified in an ACPI_DEBUG_PRINT()
+statement.
+
+The ACPI interpreter uses several different levels, but the Linux
+ACPI core and ACPI drivers generally only use ACPI_LV_INFO.
+
+You can set the debug_level mask at boot-time using the acpi.debug_level
+command line argument, and you can change it after boot by writing values
+to /sys/module/acpi/parameters/debug_level.
+
+The possible levels are defined in include/acpi/acoutput.h.  Reading
+/sys/module/acpi/parameters/debug_level shows the supported mask values,
+currently these:
+
+    ACPI_LV_INIT                    0x00000001
+    ACPI_LV_DEBUG_OBJECT            0x00000002
+    ACPI_LV_INFO                    0x00000004
+    ACPI_LV_INIT_NAMES              0x00000020
+    ACPI_LV_PARSE                   0x00000040
+    ACPI_LV_LOAD                    0x00000080
+    ACPI_LV_DISPATCH                0x00000100
+    ACPI_LV_EXEC                    0x00000200
+    ACPI_LV_NAMES                   0x00000400
+    ACPI_LV_OPREGION                0x00000800
+    ACPI_LV_BFIELD                  0x00001000
+    ACPI_LV_TABLES                  0x00002000
+    ACPI_LV_VALUES                  0x00004000
+    ACPI_LV_OBJECTS                 0x00008000
+    ACPI_LV_RESOURCES               0x00010000
+    ACPI_LV_USER_REQUESTS           0x00020000
+    ACPI_LV_PACKAGE                 0x00040000
+    ACPI_LV_ALLOCATIONS             0x00100000
+    ACPI_LV_FUNCTIONS               0x00200000
+    ACPI_LV_OPTIMIZATIONS           0x00400000
+    ACPI_LV_MUTEX                   0x01000000
+    ACPI_LV_THREADS                 0x02000000
+    ACPI_LV_IO                      0x04000000
+    ACPI_LV_INTERRUPTS              0x08000000
+    ACPI_LV_AML_DISASSEMBLE         0x10000000
+    ACPI_LV_VERBOSE_INFO            0x20000000
+    ACPI_LV_FULL_TABLES             0x40000000
+    ACPI_LV_EVENTS                  0x80000000
+
+Examples
+--------
+
+For example, drivers/acpi/bus.c contains this:
+
+    #define _COMPONENT              ACPI_BUS_COMPONENT
+    ...
+    ACPI_DEBUG_PRINT((ACPI_DB_INFO, "Device insertion detected\n"));
+
+To turn on this message, set the ACPI_BUS_COMPONENT bit in acpi.debug_layer
+and the ACPI_LV_INFO bit in acpi.debug_level.  (The ACPI_DEBUG_PRINT
+statement uses ACPI_DB_INFO, which is macro based on the ACPI_LV_INFO
+definition.)
+
+Enable all AML "Debug" output (stores to the Debug object while interpreting
+AML) during boot:
+
+    acpi.debug_layer=0xffffffff acpi.debug_level=0x2
+
+Enable PCI and PCI interrupt routing debug messages:
+
+    acpi.debug_layer=0x400000 acpi.debug_level=0x4
+
+Enable all ACPI hardware-related messages:
+
+    acpi.debug_layer=0x2 acpi.debug_level=0xffffffff
+
+Enable all ACPI_DB_INFO messages after boot:
+
+    # echo 0x4 > /sys/module/acpi/parameters/debug_level
+
+Show all valid component values:
+
+    # cat /sys/module/acpi/parameters/debug_layer

Documentation/blockdev/00-INDEX

@@ -0,0 +1,16 @@
+00-INDEX
+	- this file
+README.DAC960
+	- info on Mylex DAC960/DAC1100 PCI RAID Controller Driver for Linux.
+cciss.txt
+	- info, major/minor #'s for Compaq's SMART Array Controllers.
+cpqarray.txt
+	- info on using Compaq's SMART2 Intelligent Disk Array Controllers.
+floppy.txt
+	- notes and driver options for the floppy disk driver.
+nbd.txt
+	- info on a TCP implementation of a network block device.
+paride.txt
+	- information about the parallel port IDE subsystem.
+ramdisk.txt
+	- short guide on how to set up and use the RAM disk.

Documentation/c2port.txt

@@ -0,0 +1,90 @@
+			C2 port support
+			---------------
+
+(C) Copyright 2007 Rodolfo Giometti <giometti@enneenne.com>
+
+This program is free software; you can redistribute it and/or modify
+it under the terms of the GNU General Public License as published by
+the Free Software Foundation; either version 2 of the License, or
+(at your option) any later version.
+
+This program is distributed in the hope that it will be useful,
+but WITHOUT ANY WARRANTY; without even the implied warranty of
+MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+GNU General Public License for more details.
+
+
+
+Overview
+--------
+
+This driver implements the support for Linux of Silicon Labs (Silabs)
+C2 Interface used for in-system programming of micro controllers.
+
+By using this driver you can reprogram the in-system flash without EC2
+or EC3 debug adapter. This solution is also useful in those systems
+where the micro controller is connected via special GPIOs pins.
+
+References
+----------
+
+The C2 Interface main references are at (http://www.silabs.com)
+Silicon Laboratories site], see:
+
+- AN127: FLASH Programming via the C2 Interface at
+http://www.silabs.com/public/documents/tpub_doc/anote/Microcontrollers/Small_Form_Factor/en/an127.pdf, and
+
+- C2 Specification at
+http://www.silabs.com/public/documents/tpub_doc/spec/Microcontrollers/en/C2spec.pdf,
+
+however it implements a two wire serial communication protocol (bit
+banging) designed to enable in-system programming, debugging, and
+boundary-scan testing on low pin-count Silicon Labs devices. Currently
+this code supports only flash programming but extensions are easy to
+add.
+
+Using the driver
+----------------
+
+Once the driver is loaded you can use sysfs support to get C2port's
+info or read/write in-system flash.
+
+# ls /sys/class/c2port/c2port0/
+access            flash_block_size  flash_erase       rev_id
+dev_id            flash_blocks_num  flash_size        subsystem/
+flash_access      flash_data        reset             uevent
+
+Initially the C2port access is disabled since you hardware may have
+such lines multiplexed with other devices so, to get access to the
+C2port, you need the command:
+
+# echo 1 > /sys/class/c2port/c2port0/access
+
+after that you should read the device ID and revision ID of the
+connected micro controller:
+
+# cat /sys/class/c2port/c2port0/dev_id
+8
+# cat /sys/class/c2port/c2port0/rev_id
+1
+
+However, for security reasons, the in-system flash access in not
+enabled yet, to do so you need the command:
+
+# echo 1 > /sys/class/c2port/c2port0/flash_access
+
+After that you can read the whole flash:
+
+# cat /sys/class/c2port/c2port0/flash_data > image
+
+erase it:
+
+# echo 1 > /sys/class/c2port/c2port0/flash_erase
+
+and write it:
+
+# cat image > /sys/class/c2port/c2port0/flash_data
+
+after writing you have to reset the device to execute the new code:
+
+# echo 1 > /sys/class/c2port/c2port0/reset

Documentation/cgroups/freezer-subsystem.txt

@@ -1,4 +1,4 @@
-	The cgroup freezer is useful to batch job management system which start
+The cgroup freezer is useful to batch job management system which start
 and stop sets of tasks in order to schedule the resources of a machine
 according to the desires of a system administrator. This sort of program
 is often used on HPC clusters to schedule access to the cluster as a
@@ -6,7 +6,7 @@ whole. The cgroup freezer uses cgroups to describe the set of tasks to
 be started/stopped by the batch job management system. It also provides
 a means to start and stop the tasks composing the job.
 
-	The cgroup freezer will also be useful for checkpointing running groups
+The cgroup freezer will also be useful for checkpointing running groups
 of tasks. The freezer allows the checkpoint code to obtain a consistent
 image of the tasks by attempting to force the tasks in a cgroup into a
 quiescent state. Once the tasks are quiescent another task can
@@ -16,7 +16,7 @@ recoverable error occur. This also allows the checkpointed tasks to be
 migrated between nodes in a cluster by copying the gathered information
 to another node and restarting the tasks there.
 
-	Sequences of SIGSTOP and SIGCONT are not always sufficient for stopping
+Sequences of SIGSTOP and SIGCONT are not always sufficient for stopping
 and resuming tasks in userspace. Both of these signals are observable
 from within the tasks we wish to freeze. While SIGSTOP cannot be caught,
 blocked, or ignored it can be seen by waiting or ptracing parent tasks.
@@ -37,26 +37,29 @@ demonstrate this problem using nested bash shells:
 
 	<at this point 16990 exits and causes 16644 to exit too>
 
-	This happens because bash can observe both signals and choose how it
+This happens because bash can observe both signals and choose how it
 responds to them.
 
-	Another example of a program which catches and responds to these
+Another example of a program which catches and responds to these
 signals is gdb. In fact any program designed to use ptrace is likely to
 have a problem with this method of stopping and resuming tasks.
 
-	 In contrast, the cgroup freezer uses the kernel freezer code to
+In contrast, the cgroup freezer uses the kernel freezer code to
 prevent the freeze/unfreeze cycle from becoming visible to the tasks
 being frozen. This allows the bash example above and gdb to run as
 expected.
 
-	The freezer subsystem in the container filesystem defines a file named
+The freezer subsystem in the container filesystem defines a file named
 freezer.state. Writing "FROZEN" to the state file will freeze all tasks in the
 cgroup. Subsequently writing "THAWED" will unfreeze the tasks in the cgroup.
 Reading will return the current state.
 
+Note freezer.state doesn't exist in root cgroup, which means root cgroup
+is non-freezable.
+
 * Examples of usage :
 
-   # mkdir /containers/freezer
+   # mkdir /containers
    # mount -t cgroup -ofreezer freezer  /containers
    # mkdir /containers/0
    # echo $some_pid > /containers/0/tasks
@@ -94,6 +97,6 @@ things happens:
 		the freezer.state file
 	2) Userspace retries the freezing operation by writing "FROZEN" to
 		the freezer.state file (writing "FREEZING" is not legal
-		and returns EIO)
+		and returns EINVAL)
 	3) The tasks that blocked the cgroup from entering the "FROZEN"
 		state disappear from the cgroup's set of tasks.

Documentation/filesystems/xip.txt

@@ -39,10 +39,11 @@ The block device operation is optional, these block devices support it as of
 today:
 - dcssblk: s390 dcss block device driver
 
-An address space operation named get_xip_page is used to retrieve reference
+An address space operation named get_xip_mem is used to retrieve references
-to a struct page. To address the target page, a reference to an address_space,
+to a page frame number and a kernel address. To obtain these values a reference
-and a sector number is provided. A 3rd argument indicates whether the
+to an address_space is provided. This function assigns values to the kmem and
-function should allocate blocks if needed.
+pfn parameters. The third argument indicates whether the function should allocate
+blocks if needed.
 
 This address space operation is mutually exclusive with readpage&writepage that
 do page cache read/write operations.

Documentation/hwmon/adt7462

@@ -0,0 +1,67 @@
+Kernel driver adt7462
+======================
+
+Supported chips:
+  * Analog Devices ADT7462
+    Prefix: 'adt7462'
+    Addresses scanned: I2C 0x58, 0x5C
+    Datasheet: Publicly available at the Analog Devices website
+
+Author: Darrick J. Wong
+
+Description
+-----------
+
+This driver implements support for the Analog Devices ADT7462 chip family.
+
+This chip is a bit of a beast.  It has 8 counters for measuring fan speed.  It
+can also measure 13 voltages or 4 temperatures, or various combinations of the
+two.  See the chip documentation for more details about the exact set of
+configurations.  This driver does not allow one to configure the chip; that is
+left to the system designer.
+
+A sophisticated control system for the PWM outputs is designed into the ADT7462
+that allows fan speed to be adjusted automatically based on any of the three
+temperature sensors. Each PWM output is individually adjustable and
+programmable. Once configured, the ADT7462 will adjust the PWM outputs in
+response to the measured temperatures without further host intervention.  This
+feature can also be disabled for manual control of the PWM's.
+
+Each of the measured inputs (voltage, temperature, fan speed) has
+corresponding high/low limit values. The ADT7462 will signal an ALARM if
+any measured value exceeds either limit.
+
+The ADT7462 samples all inputs continuously. The driver will not read
+the registers more often than once every other second. Further,
+configuration data is only read once per minute.
+
+Special Features
+----------------
+
+The ADT7462 have a 10-bit ADC and can therefore measure temperatures
+with 0.25 degC resolution.
+
+The Analog Devices datasheet is very detailed and describes a procedure for
+determining an optimal configuration for the automatic PWM control.
+
+The driver will report sensor labels when it is able to determine that
+information from the configuration registers.
+
+Configuration Notes
+-------------------
+
+Besides standard interfaces driver adds the following:
+
+* PWM Control
+
+* pwm#_auto_point1_pwm and temp#_auto_point1_temp and
+* pwm#_auto_point2_pwm and temp#_auto_point2_temp -
+
+point1: Set the pwm speed at a lower temperature bound.
+point2: Set the pwm speed at a higher temperature bound.
+
+The ADT7462 will scale the pwm between the lower and higher pwm speed when
+the temperature is between the two temperature boundaries.  PWM values range
+from 0 (off) to 255 (full speed).  Fan speed will be set to maximum when the
+temperature sensor associated with the PWM control exceeds temp#_max.
+

Documentation/hwmon/lis3lv02d

@@ -0,0 +1,49 @@
+Kernel driver lis3lv02d
+==================
+
+Supported chips:
+
+  * STMicroelectronics LIS3LV02DL and LIS3LV02DQ
+
+Author:
+        Yan Burman <burman.yan@gmail.com>
+	Eric Piel <eric.piel@tremplin-utc.net>
+
+
+Description
+-----------
+
+This driver provides support for the accelerometer found in various HP laptops
+sporting the feature officially called "HP Mobile Data Protection System 3D" or
+"HP 3D DriveGuard". It detect automatically laptops with this sensor. Known models
+(for now the HP 2133, nc6420, nc2510, nc8510, nc84x0, nw9440 and nx9420) will
+have their axis automatically oriented on standard way (eg: you can directly
+play neverball).  The accelerometer data is readable via
+/sys/devices/platform/lis3lv02d.
+
+Sysfs attributes under /sys/devices/platform/lis3lv02d/:
+position - 3D position that the accelerometer reports. Format: "(x,y,z)"
+calibrate - read: values (x, y, z) that are used as the base for input class device operation.
+            write: forces the base to be recalibrated with the current position.
+rate - reports the sampling rate of the accelerometer device in HZ
+
+This driver also provides an absolute input class device, allowing
+the laptop to act as a pinball machine-esque joystick.
+
+Axes orientation
+----------------
+
+For better compatibility between the various laptops. The values reported by
+the accelerometer are converted into a "standard" organisation of the axes
+(aka "can play neverball out of the box"):
+ * When the laptop is horizontal the position reported is about 0 for X and Y
+and a positive value for Z
+ * If the left side is elevated, X increases (becomes positive)
+ * If the front side (where the touchpad is) is elevated, Y decreases (becomes negative)
+ * If the laptop is put upside-down, Z becomes negative
+
+If your laptop model is not recognized (cf "dmesg"), you can send an email to the
+authors to add it to the database.  When reporting a new laptop, please include
+the output of "dmidecode" plus the value of /sys/devices/platform/lis3lv02d/position
+in these four cases.
+

Documentation/ics932s401

@@ -0,0 +1,31 @@
+Kernel driver ics932s401
+======================
+
+Supported chips:
+  * IDT ICS932S401
+    Prefix: 'ics932s401'
+    Addresses scanned: I2C 0x69
+    Datasheet: Publically available at the IDT website
+
+Author: Darrick J. Wong
+
+Description
+-----------
+
+This driver implements support for the IDT ICS932S401 chip family.
+
+This chip has 4 clock outputs--a base clock for the CPU (which is likely
+multiplied to get the real CPU clock), a system clock, a PCI clock, a USB
+clock, and a reference clock.  The driver reports selected and actual
+frequency.  If spread spectrum mode is enabled, the driver also reports by what
+percent the clock signal is being spread, which should be between 0 and -0.5%.
+All frequencies are reported in KHz.
+
+The ICS932S401 monitors all inputs continuously. The driver will not read
+the registers more often than once every other second.
+
+Special Features
+----------------
+
+The clocks could be reprogrammed to increase system speed.  I will not help you
+do this, as you risk damaging your system!

Documentation/ioctl/00-INDEX

@@ -0,0 +1,10 @@
+00-INDEX
+	- this file
+cdrom.txt
+	- summary of CDROM ioctl calls
+hdio.txt
+	- summary of HDIO_ ioctl calls
+ioctl-decoding.txt
+	- how to decode the bits of an IOCTL code
+ioctl-number.txt
+	- how to implement and register device/driver ioctl calls

Documentation/kernel-parameters.txt

@@ -198,59 +198,42 @@ and is between 256 and 4096 characters. It is defined in the file
 			that require a timer override, but don't have
 			HPET
 
-	acpi.debug_layer=	[HW,ACPI]
+	acpi_backlight=	[HW,ACPI]
+			acpi_backlight=vendor
+			acpi_backlight=video
+			If set to vendor, prefer vendor specific driver
+			(e.g. thinkpad_acpi, sony_acpi, etc.) instead
+			of the ACPI video.ko driver.
+
+	acpi_display_output=	[HW,ACPI]
+			acpi_display_output=vendor
+			acpi_display_output=video
+			See above.
+
+	acpi.debug_layer=	[HW,ACPI,ACPI_DEBUG]
+	acpi.debug_level=	[HW,ACPI,ACPI_DEBUG]
 			Format: <int>
-			Each bit of the <int> indicates an ACPI debug layer,
+			CONFIG_ACPI_DEBUG must be enabled to produce any ACPI
-			1: enable, 0: disable. It is useful for boot time
+			debug output.  Bits in debug_layer correspond to a
-			debugging. After system has booted up, it can be set
+			_COMPONENT in an ACPI source file, e.g.,
-			via /sys/module/acpi/parameters/debug_layer.
+			    #define _COMPONENT ACPI_PCI_COMPONENT
-			CONFIG_ACPI_DEBUG must be enabled for this to produce any output.
+			Bits in debug_level correspond to a level in
-			Available bits (add the numbers together) to enable debug output
+			ACPI_DEBUG_PRINT statements, e.g.,
-			for specific parts of the ACPI subsystem:
+			    ACPI_DEBUG_PRINT((ACPI_DB_INFO, ...
-			0x01 utilities 0x02 hardware 0x04 events 0x08 tables
+			See Documentation/acpi/debug.txt for more information
-			0x10 namespace 0x20 parser 0x40 dispatcher
+			about debug layers and levels.
-			0x80 executer 0x100 resources 0x200 acpica debugger
-			0x400 os services 0x800 acpica disassembler.
-			The number can be in decimal or prefixed with 0x in hex.
-			Warning: Many of these options can produce a lot of
-			output and make your system unusable. Be very careful.
 
-	acpi.debug_level=	[HW,ACPI]
+			Enable AML "Debug" output, i.e., stores to the Debug
-			Format: <int>
+			object while interpreting AML:
-			Each bit of the <int> indicates an ACPI debug level,
+			    acpi.debug_layer=0xffffffff acpi.debug_level=0x2
-			which corresponds to the level in an ACPI_DEBUG_PRINT
+			Enable PCI/PCI interrupt routing info messages:
-			statement.  After system has booted up, this mask
+			    acpi.debug_layer=0x400000 acpi.debug_level=0x4
-			can be set via /sys/module/acpi/parameters/debug_level.
+			Enable all messages related to ACPI hardware:
+			    acpi.debug_layer=0x2 acpi.debug_level=0xffffffff
 
-			CONFIG_ACPI_DEBUG must be enabled for this to produce
+			Some values produce so much output that the system is
-			any output.  The number can be in decimal or prefixed
+			unusable.  The "log_buf_len" parameter may be useful
-			with 0x in hex.  Some of these options produce so much
+			if you need to capture more output.
-			output that the system is unusable.
-
-			The following global components are defined by the
-			ACPI CA:
-			       0x01 error
-			       0x02 warn
-			       0x04 init
-			       0x08 debug object
-			       0x10 info
-			       0x20 init names
-			       0x40 parse
-			       0x80 load
-			      0x100 dispatch
-			      0x200 execute
-			      0x400 names
-			      0x800 operation region
-			     0x1000 bfield
-			     0x2000 tables
-			     0x4000 values
-			     0x8000 objects
-			    0x10000 resources
-			    0x20000 user requests
-			    0x40000 package
- 			The number can be in decimal or prefixed with 0x in hex.
- 			Warning: Many of these options can produce a lot of
- 			output and make your system unusable. Be very careful.
 
  	acpi.power_nocheck=	[HW,ACPI]
  			Format: 1/0 enable/disable the check of power state.
@@ -646,7 +629,7 @@ and is between 256 and 4096 characters. It is defined in the file
 
 	digiepca=	[HW,SERIAL]
 			See drivers/char/README.epca and
-			Documentation/digiepca.txt.
+			Documentation/serial/digiepca.txt.
 
 	disable_mtrr_cleanup [X86]
 	enable_mtrr_cleanup [X86]
@@ -757,7 +740,7 @@ and is between 256 and 4096 characters. It is defined in the file
 			See header of drivers/scsi/fdomain.c.
 
 	floppy=		[HW]
-			See Documentation/floppy.txt.
+			See Documentation/blockdev/floppy.txt.
 
 	force_pal_cache_flush
 			[IA-64] Avoid check_sal_cache_flush which may hang on
@@ -1118,7 +1101,7 @@ and is between 256 and 4096 characters. It is defined in the file
 			the same attribute, the last one is used.
 
 	load_ramdisk=	[RAM] List of ramdisks to load from floppy
-			See Documentation/ramdisk.txt.
+			See Documentation/blockdev/ramdisk.txt.
 
 	lockd.nlm_grace_period=P  [NFS] Assign grace period.
 			Format: <integer>
@@ -1613,7 +1596,7 @@ and is between 256 and 4096 characters. It is defined in the file
 
 	pcd.		[PARIDE]
 			See header of drivers/block/paride/pcd.c.
-			See also Documentation/paride.txt.
+			See also Documentation/blockdev/paride.txt.
 
 	pci=option[,option...]	[PCI] various PCI subsystem options:
 		off		[X86] don't probe for the PCI bus
@@ -1714,7 +1697,7 @@ and is between 256 and 4096 characters. It is defined in the file
 	pcmv=		[HW,PCMCIA] BadgePAD 4
 
 	pd.		[PARIDE]
-			See Documentation/paride.txt.
+			See Documentation/blockdev/paride.txt.
 
 	pdcchassis=	[PARISC,HW] Disable/Enable PDC Chassis Status codes at
 			boot time.
@@ -1722,10 +1705,10 @@ and is between 256 and 4096 characters. It is defined in the file
 			See arch/parisc/kernel/pdc_chassis.c
 
 	pf.		[PARIDE]
-			See Documentation/paride.txt.
+			See Documentation/blockdev/paride.txt.
 
 	pg.		[PARIDE]
-			See Documentation/paride.txt.
+			See Documentation/blockdev/paride.txt.
 
 	pirq=		[SMP,APIC] Manual mp-table setup
 			See Documentation/x86/i386/IO-APIC.txt.
@@ -1795,7 +1778,7 @@ and is between 256 and 4096 characters. It is defined in the file
 
 	prompt_ramdisk=	[RAM] List of RAM disks to prompt for floppy disk
 			before loading.
-			See Documentation/ramdisk.txt.
+			See Documentation/blockdev/ramdisk.txt.
 
 	psmouse.proto=	[HW,MOUSE] Highest PS2 mouse protocol extension to
 			probe for; one of (bare|imps|exps|lifebook|any).
@@ -1815,7 +1798,7 @@ and is between 256 and 4096 characters. It is defined in the file
 			<io>,<mss_io>,<mss_irq>,<mss_dma>,<mpu_io>,<mpu_irq>
 
 	pt.		[PARIDE]
-			See Documentation/paride.txt.
+			See Documentation/blockdev/paride.txt.
 
 	pty.legacy_count=
 			[KNL] Number of legacy pty's. Overwrites compiled-in
@@ -1829,10 +1812,10 @@ and is between 256 and 4096 characters. It is defined in the file
 			See Documentation/md.txt.
 
 	ramdisk_blocksize=	[RAM]
-			See Documentation/ramdisk.txt.
+			See Documentation/blockdev/ramdisk.txt.
 
 	ramdisk_size=	[RAM] Sizes of RAM disks in kilobytes
-			See Documentation/ramdisk.txt.
+			See Documentation/blockdev/ramdisk.txt.
 
 	rcupdate.blimit=	[KNL,BOOT]
 			Set maximum number of finished RCU callbacks to process
@@ -2164,7 +2147,7 @@ and is between 256 and 4096 characters. It is defined in the file
 			See Documentation/sonypi.txt
 
 	specialix=	[HW,SERIAL] Specialix multi-serial port adapter
-			See Documentation/specialix.txt.
+			See Documentation/serial/specialix.txt.
 
 	spia_io_base=	[HW,MTD]
 	spia_fio_base=

Documentation/printk-formats.txt

@@ -0,0 +1,35 @@
+If variable is of Type,		use printk format specifier:
+---------------------------------------------------------
+		int			%d or %x
+		unsigned int		%u or %x
+		long			%ld or %lx
+		unsigned long		%lu or %lx
+		long long		%lld or %llx
+		unsigned long long	%llu or %llx
+		size_t			%zu or %zx
+		ssize_t			%zd or %zx
+
+Raw pointer value SHOULD be printed with %p.
+
+u64 SHOULD be printed with %llu/%llx, (unsigned long long):
+
+	printk("%llu", (unsigned long long)u64_var);
+
+s64 SHOULD be printed with %lld/%llx, (long long):
+
+	printk("%lld", (long long)s64_var);
+
+If <type> is dependent on a config option for its size (e.g., sector_t,
+blkcnt_t, phys_addr_t, resource_size_t) or is architecture-dependent
+for its size (e.g., tcflag_t), use a format specifier of its largest
+possible type and explicitly cast to it.  Example:
+
+	printk("test: sector number/total blocks: %llu/%llu\n",
+		(unsigned long long)sector, (unsigned long long)blockcount);
+
+Reminder: sizeof() result is of type size_t.
+
+Thank you for your cooperation and attention.
+
+
+By Randy Dunlap <rdunlap@xenotime.net>

Documentation/serial/00-INDEX

@@ -0,0 +1,24 @@
+00-INDEX
+	- this file.
+README.cycladesZ
+	- info on Cyclades-Z firmware loading.
+computone.txt
+	- info on Computone Intelliport II/Plus Multiport Serial Driver.
+digiepca.txt
+	- info on Digi Intl. {PC,PCI,EISA}Xx and Xem series cards.
+hayes-esp.txt
+	- info on using the Hayes ESP serial driver.
+moxa-smartio
+	- file with info on installing/using Moxa multiport serial driver.
+riscom8.txt
+	- notes on using the RISCom/8 multi-port serial driver.
+rocket.txt
+	- info on the Comtrol RocketPort multiport serial driver.
+specialix.txt
+	- info on hardware/driver for specialix IO8+ multiport serial card.
+stallion.txt
+	- info on using the Stallion multiport serial driver.
+sx.txt
+	- info on the Specialix SX/SI multiport serial driver.
+tty.txt
+	- guide to the locking policies of the tty layer.

Documentation/serial/computone.txt

@@ -247,7 +247,7 @@ shar archive to make it easier to extract the script from the documentation.
 To create the ip2mkdev shell script change to a convenient directory (/tmp
 works just fine) and run the following command:
 
-	unshar Documentation/computone.txt
+	unshar Documentation/serial/computone.txt
 		(This file)
 
 You should now have a file ip2mkdev in your current working directory with

Documentation/w1/masters/omap-hdq

@@ -0,0 +1,46 @@
+Kernel driver for omap HDQ/1-wire module.
+========================================
+
+Supported chips:
+================
+	HDQ/1-wire controller on the TI OMAP 2430/3430 platforms.
+
+A useful link about HDQ basics:
+===============================
+http://focus.ti.com/lit/an/slua408/slua408.pdf
+
+Description:
+============
+The HDQ/1-Wire module of TI OMAP2430/3430 platforms implement the hardware
+protocol of the master functions of the Benchmark HDQ and the Dallas
+Semiconductor 1-Wire protocols. These protocols use a single wire for
+communication between the master (HDQ/1-Wire controller) and the slave
+(HDQ/1-Wire external compliant device).
+
+A typical application of the HDQ/1-Wire module is the communication with battery
+monitor (gas gauge) integrated circuits.
+
+The controller supports operation in both HDQ and 1-wire mode. The essential
+difference between the HDQ and 1-wire mode is how the slave device responds to
+initialization pulse.In HDQ mode, the firmware does not require the host to
+create an initialization pulse to the slave.However, the slave can be reset by
+using an initialization pulse (also referred to as a break pulse).The slave
+does not respond with a presence pulse as it does in the 1-Wire protocol.
+
+Remarks:
+========
+The driver (drivers/w1/masters/omap_hdq.c) supports the HDQ mode of the
+controller. In this mode, as we can not read the ID which obeys the W1
+spec(family:id:crc), a module parameter can be passed to the driver which will
+be used to calculate the CRC and pass back an appropriate slave ID to the W1
+core.
+
+By default the master driver and the BQ slave i/f
+driver(drivers/w1/slaves/w1_bq27000.c) sets the ID to 1.
+Please note to load both the modules with a different ID if required, but note
+that the ID used should be same for both master and slave driver loading.
+
+e.g:
+insmod omap_hdq.ko W1_ID=2
+inamod w1_bq27000.ko F_ID=2
+

MAINTAINERS

@@ -2211,6 +2211,13 @@ M:	adaplas@gmail.com
 L:	linux-fbdev-devel@lists.sourceforge.net (moderated for non-subscribers)
 S:	Maintained
 
+INTEL MENLOW THERMAL DRIVER
+P:	Sujith Thomas
+M:	sujith.thomas@intel.com
+L:	linux-acpi@vger.kernel.org
+W:	http://www.lesswatts.org/projects/acpi/
+S:	Supported
+
 INTEL IA32 MICROCODE UPDATE SUPPORT
 P:	Tigran Aivazian
 M:	tigran@aivazian.fsnet.co.uk
@@ -2691,6 +2698,11 @@ P:	Arnaldo Carvalho de Melo
 M:	acme@ghostprotocols.net
 S:	Maintained
 
+LIS3LV02D ACCELEROMETER DRIVER
+P:	Eric Piel
+M:	eric.piel@tremplin-utc.net
+S:	Maintained
+
 LM83 HARDWARE MONITOR DRIVER
 P:	Jean Delvare
 M:	khali@linux-fr.org
@@ -3372,7 +3384,9 @@ S:	Maintained
 
 PNP SUPPORT
 P:	Adam Belay
-M:	ambx1@neo.rr.com
+M:	abelay@mit.edu
+P:	Bjorn Helgaas
+M:	bjorn.helgaas@hp.com
 S:	Maintained
 
 PNXxxxx I2C DRIVER
@@ -3915,8 +3929,6 @@ M:	bootc@bootc.net
 S:	Maintained
 
 SOFTWARE RAID (Multiple Disks) SUPPORT
-P:	Ingo Molnar
-M:	mingo@redhat.com
 P:	Neil Brown
 M:	neilb@suse.de
 L:	linux-raid@vger.kernel.org

Makefile

@@ -1,7 +1,7 @@
 VERSION = 2
 PATCHLEVEL = 6
 SUBLEVEL = 28
-EXTRAVERSION = -rc4
+EXTRAVERSION = -rc5
 NAME = Killer Bat of Doom
 
 # *DOCUMENTATION*

arch/arm/include/asm/dma-mapping.h

@@ -256,8 +256,17 @@ int dmabounce_sync_for_cpu(struct device *, dma_addr_t, unsigned long,
 int dmabounce_sync_for_device(struct device *, dma_addr_t, unsigned long,
 		size_t, enum dma_data_direction);
 #else
-#define dmabounce_sync_for_cpu(dev,dma,off,sz,dir)	(1)
+static inline int dmabounce_sync_for_cpu(struct device *d, dma_addr_t addr,
-#define dmabounce_sync_for_device(dev,dma,off,sz,dir)	(1)
+	unsigned long offset, size_t size, enum dma_data_direction dir)
+{
+	return 1;
+}
+
+static inline int dmabounce_sync_for_device(struct device *d, dma_addr_t addr,
+	unsigned long offset, size_t size, enum dma_data_direction dir)
+{
+	return 1;
+}
 
 
 /**

arch/arm/include/asm/hardware/iop3xx-adma.h

@@ -730,7 +730,8 @@ static inline void iop_desc_set_next_desc(struct iop_adma_desc_slot *desc,
 {
 	/* hw_desc->next_desc is the same location for all channels */
 	union iop3xx_desc hw_desc = { .ptr = desc->hw_desc, };
-	BUG_ON(hw_desc.dma->next_desc);
+
+	iop_paranoia(hw_desc.dma->next_desc);
 	hw_desc.dma->next_desc = next_desc_addr;
 }
 
@@ -760,7 +761,7 @@ static inline int iop_desc_get_zero_result(struct iop_adma_desc_slot *desc)
 	struct iop3xx_desc_aau *hw_desc = desc->hw_desc;
 	struct iop3xx_aau_desc_ctrl desc_ctrl = hw_desc->desc_ctrl_field;
 
-	BUG_ON(!(desc_ctrl.tx_complete && desc_ctrl.zero_result_en));
+	iop_paranoia(!(desc_ctrl.tx_complete && desc_ctrl.zero_result_en));
 	return desc_ctrl.zero_result_err;
 }
 

arch/arm/include/asm/hardware/iop_adma.h

@@ -23,6 +23,12 @@
 
 #define IOP_ADMA_SLOT_SIZE 32
 #define IOP_ADMA_THRESHOLD 4
+#ifdef DEBUG
+#define IOP_PARANOIA 1
+#else
+#define IOP_PARANOIA 0
+#endif
+#define iop_paranoia(x) BUG_ON(IOP_PARANOIA && (x))
 
 /**
  * struct iop_adma_device - internal representation of an ADMA device

arch/arm/include/asm/mach/map.h

@@ -19,12 +19,13 @@ struct map_desc {
 };
 
 /* types 0-3 are defined in asm/io.h */
-#define MT_CACHECLEAN		4
+#define MT_UNCACHED		4
-#define MT_MINICLEAN		5
+#define MT_CACHECLEAN		5
-#define MT_LOW_VECTORS		6
+#define MT_MINICLEAN		6
-#define MT_HIGH_VECTORS		7
+#define MT_LOW_VECTORS		7
-#define MT_MEMORY		8
+#define MT_HIGH_VECTORS		8
-#define MT_ROM			9
+#define MT_MEMORY		9
+#define MT_ROM			10
 
 #ifdef CONFIG_MMU
 extern void iotable_init(struct map_desc *, int);

arch/arm/mach-clps711x/include/mach/hardware.h

@@ -94,20 +94,6 @@
 #include <asm/hardware/ep7212.h>
 #include <asm/hardware/cs89712.h>
 
-/* dynamic ioremap() areas */
-#define FLASH_START      0x00000000
-#define FLASH_SIZE       0x800000
-#define FLASH_WIDTH      4
-
-#define SRAM_START       0x60000000
-#define SRAM_SIZE        0xc000
-#define SRAM_WIDTH       4
-
-#define BOOTROM_START    0x70000000
-#define BOOTROM_SIZE     0x80
-#define BOOTROM_WIDTH    4
-
-
 /* static cdb89712_map_io() areas */
 #define REGISTER_START   0x80000000
 #define REGISTER_SIZE    0x4000
@@ -198,14 +184,6 @@
 #define CEIVA_FLASH_SIZE        0x100000
 #define CEIVA_FLASH_WIDTH       2
 
-#define SRAM_START       0x60000000
-#define SRAM_SIZE        0xc000
-#define SRAM_WIDTH       4
-
-#define BOOTROM_START    0x70000000
-#define BOOTROM_SIZE     0x80
-#define BOOTROM_WIDTH    4
-
 /*
  * SED1355 LCD controller
  */

arch/arm/mach-clps7500/core.c

@@ -275,9 +275,9 @@ static struct map_desc cl7500_io_desc[] __initdata = {
 		.length		= ISA_SIZE,
 		.type		= MT_DEVICE
 	}, {	/* Flash	*/
-		.virtual	= FLASH_BASE,
+		.virtual	= CLPS7500_FLASH_BASE,
-		.pfn		= __phys_to_pfn(FLASH_START),
+		.pfn		= __phys_to_pfn(CLPS7500_FLASH_START),
-		.length		= FLASH_SIZE,
+		.length		= CLPS7500_FLASH_SIZE,
 		.type		= MT_DEVICE
 	}, {	/* LED		*/
 		.virtual	= LED_BASE,

arch/arm/mach-clps7500/include/mach/hardware.h

@@ -39,9 +39,9 @@
 #define ISA_SIZE		0x00010000
 #define ISA_BASE		0xe1000000
 
-#define FLASH_START		0x01000000	/* XXX */
+#define CLPS7500_FLASH_START	0x01000000	/* XXX */
-#define FLASH_SIZE		0x01000000
+#define CLPS7500_FLASH_SIZE	0x01000000
-#define FLASH_BASE		0xe2000000
+#define CLPS7500_FLASH_BASE	0xe2000000
 
 #define LED_START		0x0302B000
 #define LED_SIZE		0x00001000

arch/arm/mach-h720x/include/mach/boards.h

@@ -19,9 +19,9 @@
 #ifdef CONFIG_ARCH_H7202
 
 /* FLASH */
-#define FLASH_VIRT		0xd0000000
+#define H720X_FLASH_VIRT	0xd0000000
-#define FLASH_PHYS		0x00000000
+#define H720X_FLASH_PHYS	0x00000000
-#define FLASH_SIZE		0x02000000
+#define H720X_FLASH_SIZE	0x02000000
 
 /* onboard LAN controller */
 # define ETH0_PHYS		0x08000000

arch/arm/mach-integrator/include/mach/platform.h

@@ -407,28 +407,11 @@
  */
 #define uHAL_MEMORY_SIZE                INTEGRATOR_SSRAM_SIZE
 
-/*
- *  Application Flash
- *
- */
-#define FLASH_BASE                      INTEGRATOR_FLASH_BASE
-#define FLASH_SIZE                      INTEGRATOR_FLASH_SIZE
-#define FLASH_END                       (FLASH_BASE + FLASH_SIZE - 1)
-#define FLASH_BLOCK_SIZE                SZ_128K
-
-/*
- *  Boot Flash
- *
- */
-#define EPROM_BASE                      INTEGRATOR_BOOT_ROM_HI
-#define EPROM_SIZE                      INTEGRATOR_BOOT_ROM_SIZE
-#define EPROM_END                       (EPROM_BASE + EPROM_SIZE - 1)
-
 /*
  *  Clean base - dummy
  *
  */
-#define CLEAN_BASE                      EPROM_BASE
+#define CLEAN_BASE                      INTEGRATOR_BOOT_ROM_HI
 
 /*
  *  Timer definitions

arch/arm/mach-iop13xx/include/mach/adma.h

@@ -404,7 +404,8 @@ static inline void iop_desc_set_next_desc(struct iop_adma_desc_slot *desc,
 					u32 next_desc_addr)
 {
 	struct iop13xx_adma_desc_hw *hw_desc = desc->hw_desc;
-	BUG_ON(hw_desc->next_desc);
+
+	iop_paranoia(hw_desc->next_desc);
 	hw_desc->next_desc = next_desc_addr;
 }
 

arch/arm/mach-realview/clock.c

@@ -104,7 +104,7 @@ static struct clk uart_clk = {
 
 static struct clk mmci_clk = {
 	.name	= "MCLK",
-	.rate	= 33000000,
+	.rate	= 24000000,
 };
 
 int clk_register(struct clk *clk)

arch/arm/mach-realview/include/mach/platform.h

@@ -238,28 +238,11 @@
 #define REALVIEW_INTREG_OFFSET		0x8	/* Interrupt control */
 #define REALVIEW_DECODE_OFFSET		0xC	/* Fitted logic modules */
 
-/* 
- *  Application Flash
- * 
- */
-#define FLASH_BASE                      REALVIEW_FLASH_BASE
-#define FLASH_SIZE                      REALVIEW_FLASH_SIZE
-#define FLASH_END                       (FLASH_BASE + FLASH_SIZE - 1)
-#define FLASH_BLOCK_SIZE                SZ_128K
-
-/* 
- *  Boot Flash
- * 
- */
-#define EPROM_BASE                      REALVIEW_BOOT_ROM_HI
-#define EPROM_SIZE                      REALVIEW_BOOT_ROM_SIZE
-#define EPROM_END                       (EPROM_BASE + EPROM_SIZE - 1)
-
 /* 
  *  Clean base - dummy
  * 
  */
-#define CLEAN_BASE                      EPROM_BASE
+#define CLEAN_BASE                      REALVIEW_BOOT_ROM_HI
 
 /*
  * System controller bit assignment

arch/arm/mach-versatile/clock.c

@@ -105,7 +105,7 @@ static struct clk uart_clk = {
 
 static struct clk mmci_clk = {
 	.name	= "MCLK",
-	.rate	= 33000000,
+	.rate	= 24000000,
 };
 
 int clk_register(struct clk *clk)

arch/arm/mach-versatile/include/mach/platform.h

@@ -436,28 +436,12 @@
 #define SIC_INTMASK_PCI1                (1 << SIC_INT_PCI1)
 #define SIC_INTMASK_PCI2                (1 << SIC_INT_PCI2)
 #define SIC_INTMASK_PCI3                (1 << SIC_INT_PCI3)
-/* 
- *  Application Flash
- * 
- */
-#define FLASH_BASE                      VERSATILE_FLASH_BASE
-#define FLASH_SIZE                      VERSATILE_FLASH_SIZE
-#define FLASH_END                       (FLASH_BASE + FLASH_SIZE - 1)
-#define FLASH_BLOCK_SIZE                SZ_128K
-
-/* 
- *  Boot Flash
- * 
- */
-#define EPROM_BASE                      VERSATILE_BOOT_ROM_HI
-#define EPROM_SIZE                      VERSATILE_BOOT_ROM_SIZE
-#define EPROM_END                       (EPROM_BASE + EPROM_SIZE - 1)
 
 /* 
  *  Clean base - dummy
  * 
  */
-#define CLEAN_BASE                      EPROM_BASE
+#define CLEAN_BASE                      VERSATILE_BOOT_ROM_HI
 
 /*
  * System controller bit assignment

arch/arm/mm/cache-feroceon-l2.c

@@ -150,7 +150,7 @@ static void feroceon_l2_inv_range(unsigned long start, unsigned long end)
 	/*
 	 * Clean and invalidate partial last cache line.
 	 */
-	if (end & (CACHE_LINE_SIZE - 1)) {
+	if (start < end && end & (CACHE_LINE_SIZE - 1)) {
 		l2_clean_inv_pa(end & ~(CACHE_LINE_SIZE - 1));
 		end &= ~(CACHE_LINE_SIZE - 1);
 	}
@@ -158,7 +158,7 @@ static void feroceon_l2_inv_range(unsigned long start, unsigned long end)
 	/*
 	 * Invalidate all full cache lines between 'start' and 'end'.
 	 */
-	while (start != end) {
+	while (start < end) {
 		unsigned long range_end = calc_range_end(start, end);
 		l2_inv_pa_range(start, range_end - CACHE_LINE_SIZE);
 		start = range_end;

arch/arm/mm/mmu.c

@@ -208,6 +208,12 @@ static struct mem_type mem_types[] = {
 		.prot_sect	= PROT_SECT_DEVICE,
 		.domain		= DOMAIN_IO,
 	},
+	[MT_UNCACHED] = {
+		.prot_pte	= PROT_PTE_DEVICE,
+		.prot_l1	= PMD_TYPE_TABLE,
+		.prot_sect	= PMD_TYPE_SECT | PMD_SECT_XN,
+		.domain		= DOMAIN_IO,
+	},
 	[MT_CACHECLEAN] = {
 		.prot_sect = PMD_TYPE_SECT | PMD_SECT_XN,
 		.domain    = DOMAIN_KERNEL,

arch/arm/plat-iop/setup.c

@@ -16,14 +16,15 @@
 #include <asm/hardware/iop3xx.h>
 
 /*
- * Standard IO mapping for all IOP3xx based systems
+ * Standard IO mapping for all IOP3xx based systems.  Note that
+ * the IOP3xx OCCDR must be mapped uncached and unbuffered.
  */
 static struct map_desc iop3xx_std_desc[] __initdata = {
 	 {	/* mem mapped registers */
 		.virtual	= IOP3XX_PERIPHERAL_VIRT_BASE,
 		.pfn		= __phys_to_pfn(IOP3XX_PERIPHERAL_PHYS_BASE),
 		.length		= IOP3XX_PERIPHERAL_SIZE,
-		.type		= MT_DEVICE,
+		.type		= MT_UNCACHED,
 	 }, {	/* PCI IO space */
 		.virtual	= IOP3XX_PCI_LOWER_IO_VA,
 		.pfn		= __phys_to_pfn(IOP3XX_PCI_LOWER_IO_PA),

arch/blackfin/include/asm/bfin-global.h

@@ -101,7 +101,7 @@ extern u16 _bfin_swrst; /* shadow for Software Reset Register (SWRST) */
 extern unsigned long _ramstart, _ramend, _rambase;
 extern unsigned long memory_start, memory_end, physical_mem_end;
 extern char _stext_l1[], _etext_l1[], _sdata_l1[], _edata_l1[], _sbss_l1[],
-	_ebss_l1[], _l1_lma_start[], _sdata_b_l1[], _ebss_b_l1[],
+	_ebss_l1[], _l1_lma_start[], _sdata_b_l1[], _sbss_b_l1[], _ebss_b_l1[],
 	_stext_l2[], _etext_l2[], _sdata_l2[], _edata_l2[], _sbss_l2[],
 	_ebss_l2[], _l2_lma_start[];
 

arch/blackfin/include/asm/dma-mapping.h

@@ -15,7 +15,11 @@ void dma_free_coherent(struct device *dev, size_t size, void *vaddr,
 #define dma_alloc_noncoherent(d, s, h, f) dma_alloc_coherent(d, s, h, f)
 #define dma_free_noncoherent(d, s, v, h) dma_free_coherent(d, s, v, h)
 
-#define dma_mapping_error
+static inline
+int dma_mapping_error(struct device *dev, dma_addr_t dma_addr)
+{
+	return 0;
+}
 
 /*
  * Map a single buffer of the indicated size for DMA in streaming mode.

arch/blackfin/kernel/bfin_gpio.c

@@ -218,7 +218,7 @@ inline int check_gpio(unsigned gpio)
 	if (gpio == GPIO_PB15 || gpio == GPIO_PC14 || gpio == GPIO_PC15
 	    || gpio == GPIO_PH14 || gpio == GPIO_PH15
 	    || gpio == GPIO_PJ14 || gpio == GPIO_PJ15
-	    || gpio > MAX_BLACKFIN_GPIOS)
+	    || gpio >= MAX_BLACKFIN_GPIOS)
 		return -EINVAL;
 	return 0;
 }

arch/blackfin/kernel/cplb-nompu/cplbinit.c

@@ -188,10 +188,11 @@ static struct cplb_desc cplb_data[] = {
 
 static u16 __init lock_kernel_check(u32 start, u32 end)
 {
-	if ((end   <= (u32) _end && end   >= (u32)_stext) ||
+	if (start >= (u32)_end || end <= (u32)_stext)
-	    (start <= (u32) _end && start >= (u32)_stext))
+		return 0;
-		return IN_KERNEL;
+
-	return 0;
+	/* This cplb block overlapped with kernel area. */
+	return IN_KERNEL;
 }
 
 static unsigned short __init

arch/blackfin/kernel/process.c

@@ -351,9 +351,14 @@ int _access_ok(unsigned long addr, unsigned long size)
 		return 1;
 #endif
 #if L1_DATA_B_LENGTH != 0
-	if (addr >= L1_DATA_B_START
+	if (addr >= L1_DATA_B_START + (_ebss_b_l1 - _sdata_b_l1)
 	    && addr + size <= L1_DATA_B_START + L1_DATA_B_LENGTH)
 		return 1;
+#endif
+#if L2_LENGTH != 0
+	if (addr >= L2_START + (_ebss_l2 - _stext_l2)
+	    && addr + size <= L2_START + L2_LENGTH)
+		return 1;
 #endif
 	return 0;
 }

arch/blackfin/kernel/setup.c

@@ -119,23 +119,23 @@ void __init bfin_relocate_l1_mem(void)
 	/* Copy _stext_l1 to _etext_l1 to L1 instruction SRAM */
 	dma_memcpy(_stext_l1, _l1_lma_start, l1_code_length);
 
-	l1_data_a_length = _ebss_l1 - _sdata_l1;
+	l1_data_a_length = _sbss_l1 - _sdata_l1;
 	if (l1_data_a_length > L1_DATA_A_LENGTH)
 		panic("L1 Data SRAM Bank A Overflow\n");
 
-	/* Copy _sdata_l1 to _ebss_l1 to L1 data bank A SRAM */
+	/* Copy _sdata_l1 to _sbss_l1 to L1 data bank A SRAM */
 	dma_memcpy(_sdata_l1, _l1_lma_start + l1_code_length, l1_data_a_length);
 
-	l1_data_b_length = _ebss_b_l1 - _sdata_b_l1;
+	l1_data_b_length = _sbss_b_l1 - _sdata_b_l1;
 	if (l1_data_b_length > L1_DATA_B_LENGTH)
 		panic("L1 Data SRAM Bank B Overflow\n");
 
-	/* Copy _sdata_b_l1 to _ebss_b_l1 to L1 data bank B SRAM */
+	/* Copy _sdata_b_l1 to _sbss_b_l1 to L1 data bank B SRAM */
 	dma_memcpy(_sdata_b_l1, _l1_lma_start + l1_code_length +
 			l1_data_a_length, l1_data_b_length);
 
 	if (L2_LENGTH != 0) {
-		l2_length = _ebss_l2 - _stext_l2;
+		l2_length = _sbss_l2 - _stext_l2;
 		if (l2_length > L2_LENGTH)
 			panic("L2 SRAM Overflow\n");
 
@@ -827,7 +827,7 @@ void __init setup_arch(char **cmdline_p)
 				printk(KERN_ERR "Warning: Compiled for Rev %d, but running on Rev %d\n",
 				       bfin_compiled_revid(), bfin_revid());
 		}
-		if (bfin_revid() <= CONFIG_BF_REV_MIN || bfin_revid() > CONFIG_BF_REV_MAX)
+		if (bfin_revid() < CONFIG_BF_REV_MIN || bfin_revid() > CONFIG_BF_REV_MAX)
 			printk(KERN_ERR "Warning: Unsupported Chip Revision ADSP-%s Rev 0.%d detected\n",
 			       CPU, bfin_revid());
 	}

arch/blackfin/kernel/traps.c

@@ -59,7 +59,7 @@
 #endif
 
 
-#ifdef CONFIG_VERBOSE_DEBUG
+#ifdef CONFIG_DEBUG_VERBOSE
 #define verbose_printk(fmt, arg...) \
 	printk(fmt, ##arg)
 #else
@@ -147,9 +147,12 @@ static void decode_address(char *buf, unsigned long address)
 				char *name = p->comm;
 				struct file *file = vma->vm_file;
 
-				if (file)
+				if (file) {
-					name = d_path(&file->f_path, _tmpbuf,
+					char *d_name = d_path(&file->f_path, _tmpbuf,
 						      sizeof(_tmpbuf));
+					if (!IS_ERR(d_name))
+						name = d_name;
+				}
 
 				/* FLAT does not have its text aligned to the start of
 				 * the map while FDPIC ELF does ...
@@ -571,7 +574,7 @@ asmlinkage void trap_c(struct pt_regs *fp)
 #endif
 			panic("Kernel exception");
 		} else {
-#ifdef CONFIG_VERBOSE_DEBUG
+#ifdef CONFIG_DEBUG_VERBOSE
 			unsigned long *stack;
 			/* Dump the user space stack */
 			stack = (unsigned long *)rdusp();

arch/blackfin/mach-common/cache.S

@@ -25,9 +25,13 @@
  */
 .macro do_flush flushins:req optflushins optnopins label
 
+	R2 = -L1_CACHE_BYTES;
+
+	/* start = (start & -L1_CACHE_BYTES) */
+	R0 = R0 & R2;
+
 	/* end = ((end - 1) & -L1_CACHE_BYTES) + L1_CACHE_BYTES; */
 	R1 += -1;
-	R2 = -L1_CACHE_BYTES;
 	R1 = R1 & R2;
 	R1 += L1_CACHE_BYTES;
 
@@ -63,7 +67,7 @@ ENDPROC(_blackfin_icache_flush_range)
 
 /* Flush all cache lines assocoiated with this area of memory. */
 ENTRY(_blackfin_icache_dcache_flush_range)
-	do_flush IFLUSH, FLUSH
+	do_flush FLUSH, IFLUSH
 ENDPROC(_blackfin_icache_dcache_flush_range)
 
 /* Throw away all D-cached data in specified region without any obligation to

arch/blackfin/mach-common/cpufreq.c

@@ -72,13 +72,13 @@ unsigned int __bfin_cycles_mod;
 
 /**************************************************************************/
 
-static unsigned int bfin_getfreq(unsigned int cpu)
+static unsigned int bfin_getfreq_khz(unsigned int cpu)
 {
 	/* The driver only support single cpu */
 	if (cpu != 0)
 		return -1;
 
-	return get_cclk();
+	return get_cclk() / 1000;
 }
 
 
@@ -96,7 +96,7 @@ static int bfin_target(struct cpufreq_policy *policy,
 
 	cclk_hz = bfin_freq_table[index].frequency;
 
-	freqs.old = bfin_getfreq(0);
+	freqs.old = bfin_getfreq_khz(0);
 	freqs.new = cclk_hz;
 	freqs.cpu = 0;
 
@@ -137,8 +137,8 @@ static int __init __bfin_cpu_init(struct cpufreq_policy *policy)
 	if (policy->cpu != 0)
 		return -EINVAL;
 
-	cclk = get_cclk();
+	cclk = get_cclk() / 1000;
-	sclk = get_sclk();
+	sclk = get_sclk() / 1000;
 
 #if ANOMALY_05000273 || (!defined(CONFIG_BF54x) && defined(CONFIG_BFIN_DCACHE))
 	min_cclk = sclk * 2;
@@ -152,7 +152,7 @@ static int __init __bfin_cpu_init(struct cpufreq_policy *policy)
 		dpm_state_table[index].csel = csel << 4; /* Shift now into PLL_DIV bitpos */
 		dpm_state_table[index].tscale =  (TIME_SCALE / (1 << csel)) - 1;
 
-		pr_debug("cpufreq: freq:%d csel:%d tscale:%d\n",
+		pr_debug("cpufreq: freq:%d csel:0x%x tscale:%d\n",
 						 bfin_freq_table[index].frequency,
 						 dpm_state_table[index].csel,
 						 dpm_state_table[index].tscale);
@@ -173,7 +173,7 @@ static struct freq_attr *bfin_freq_attr[] = {
 static struct cpufreq_driver bfin_driver = {
 	.verify = bfin_verify_speed,
 	.target = bfin_target,
-	.get = bfin_getfreq,
+	.get = bfin_getfreq_khz,
 	.init = __bfin_cpu_init,
 	.name = "bfin cpufreq",
 	.owner = THIS_MODULE,

arch/blackfin/mach-common/entry.S

@@ -277,7 +277,7 @@ ENTRY(_bfin_return_from_exception)
 	p5.h = hi(ILAT);
 	r6 = [p5];
 	r7 = 0x20;		/* Did I just cause anther HW error? */
-	r7 = r7 & r1;
+	r6 = r7 & r6;
 	CC = R7 == R6;
 	if CC JUMP _double_fault;
 #endif

arch/blackfin/mm/sram-alloc.c

@@ -183,10 +183,10 @@ static void __init l2_sram_init(void)
 		return;
 	}
 
-	free_l2_sram_head.next->paddr = (void *)L2_START +
+	free_l2_sram_head.next->paddr =
-		(_etext_l2 - _stext_l2) + (_edata_l2 - _sdata_l2);
+		(void *)L2_START + (_ebss_l2 - _stext_l2);
-	free_l2_sram_head.next->size = L2_LENGTH -
+	free_l2_sram_head.next->size =
-		(_etext_l2 - _stext_l2) + (_edata_l2 - _sdata_l2);
+		L2_LENGTH - (_ebss_l2 - _stext_l2);
 	free_l2_sram_head.next->pid = 0;
 	free_l2_sram_head.next->next = NULL;
 

arch/ia64/kvm/Kconfig

@@ -20,6 +20,8 @@ if VIRTUALIZATION
 config KVM
 	tristate "Kernel-based Virtual Machine (KVM) support"
 	depends on HAVE_KVM && EXPERIMENTAL
+	# for device assignment:
+	depends on PCI
 	select PREEMPT_NOTIFIERS
 	select ANON_INODES
 	---help---

arch/ia64/kvm/kvm-ia64.c

@@ -673,16 +673,16 @@ int kvm_arch_vcpu_ioctl_run(struct kvm_vcpu *vcpu, struct kvm_run *kvm_run)
 
 	vcpu_load(vcpu);
 
+	if (vcpu->sigset_active)
+		sigprocmask(SIG_SETMASK, &vcpu->sigset, &sigsaved);
+
 	if (unlikely(vcpu->arch.mp_state == KVM_MP_STATE_UNINITIALIZED)) {
 		kvm_vcpu_block(vcpu);
 		clear_bit(KVM_REQ_UNHALT, &vcpu->requests);
-		vcpu_put(vcpu);
+		r = -EAGAIN;
-		return -EAGAIN;
+		goto out;
 	}
 
-	if (vcpu->sigset_active)
-		sigprocmask(SIG_SETMASK, &vcpu->sigset, &sigsaved);
-
 	if (vcpu->mmio_needed) {
 		memcpy(vcpu->mmio_data, kvm_run->mmio.data, 8);
 		kvm_set_mmio_data(vcpu);
@@ -690,7 +690,7 @@ int kvm_arch_vcpu_ioctl_run(struct kvm_vcpu *vcpu, struct kvm_run *kvm_run)
 		vcpu->mmio_needed = 0;
 	}
 	r = __vcpu_run(vcpu, kvm_run);
-
+out:
 	if (vcpu->sigset_active)
 		sigprocmask(SIG_SETMASK, &sigsaved, NULL);
 

arch/ia64/kvm/vcpu.h

@@ -384,6 +384,10 @@ static inline u64 __gpfn_is_io(u64 gpfn)
 #define MODE_IND(psr)	\
 	(((psr).it << 2) + ((psr).dt << 1) + (psr).rt)
 
+#ifndef CONFIG_SMP
+#define _vmm_raw_spin_lock(x)	 do {}while(0)
+#define _vmm_raw_spin_unlock(x) do {}while(0)
+#else
 #define _vmm_raw_spin_lock(x)						\
 	do {								\
 		__u32 *ia64_spinlock_ptr = (__u32 *) (x);		\
@@ -403,6 +407,7 @@ static inline u64 __gpfn_is_io(u64 gpfn)
 	do { barrier();				\
 		((spinlock_t *)x)->raw_lock.lock = 0; } \
 while (0)
+#endif
 
 void vmm_spin_lock(spinlock_t *lock);
 void vmm_spin_unlock(spinlock_t *lock);

arch/m68k/kernel/ints.c

@@ -133,7 +133,7 @@ void __init m68k_setup_user_interrupt(unsigned int vec, unsigned int cnt,
 {
 	int i;
 
-	BUG_ON(IRQ_USER + cnt >= NR_IRQS);
+	BUG_ON(IRQ_USER + cnt > NR_IRQS);
 	m68k_first_user_vec = vec;
 	for (i = 0; i < cnt; i++)
 		irq_controller[IRQ_USER + i] = &user_irq_controller;

arch/mn10300/Kconfig.debug

@@ -15,6 +15,15 @@ config DEBUG_DECOMPRESS_KERNEL
 	  decompressing Linux seeing "Uncompressing Linux... " and
 	  "Ok, booting the kernel.\n" on console.
 
+config TEST_MISALIGNMENT_HANDLER
+	bool "Run tests on the misalignment handler"
+	depends on DEBUG_KERNEL
+	default n
+	help
+	  If you say Y here the kernel will execute a list of misaligned memory
+	  accesses to make sure the misalignment handler deals them with
+	  correctly.  If it does not, the kernel will throw a BUG.
+
 config KPROBES
 	bool "Kprobes"
 	depends on DEBUG_KERNEL

arch/mn10300/mm/misalignment.c

@@ -37,26 +37,22 @@
 #include <asm/asm-offsets.h>
 
 #if 0
-#define kdebug(FMT, ...) printk(KERN_DEBUG FMT, ##__VA_ARGS__)
+#define kdebug(FMT, ...) printk(KERN_DEBUG "MISALIGN: "FMT"\n", ##__VA_ARGS__)
 #else
 #define kdebug(FMT, ...) do {} while (0)
 #endif
 
-static int misalignment_addr(unsigned long *registers, unsigned params,
+static int misalignment_addr(unsigned long *registers, unsigned long sp,
-			     unsigned opcode, unsigned disp,
+			     unsigned params, unsigned opcode,
-			     void **_address, unsigned long **_postinc);
+			     unsigned long disp,
+			     void **_address, unsigned long **_postinc,
+			     unsigned long *_inc);
 
 static int misalignment_reg(unsigned long *registers, unsigned params,
-			    unsigned opcode, unsigned disp,
+			    unsigned opcode, unsigned long disp,
 			    unsigned long **_register);
 
-static inline unsigned int_log2(unsigned x)
+static void misalignment_MOV_Lcc(struct pt_regs *regs, uint32_t opcode);
-{
-	unsigned y;
-	asm("bsch %1,%0" : "=r"(y) : "r"(x), "0"(0));
-	return y;
-}
-#define log2(x) int_log2(x)
 
 static const unsigned Dreg_index[] = {
 	REG_D0 >> 2, REG_D1 >> 2, REG_D2 >> 2, REG_D3 >> 2
@@ -86,9 +82,10 @@ enum format_id {
 	FMT_D7,
 	FMT_D8,
 	FMT_D9,
+	FMT_D10,
 };
 
-struct {
+static const struct {
 	u_int8_t opsz, dispsz;
 } format_tbl[16] = {
 	[FMT_S0]	= { 8,	0	},
@@ -103,6 +100,7 @@ struct {
 	[FMT_D7]	= { 24,	8	},
 	[FMT_D8]	= { 24,	24	},
 	[FMT_D9]	= { 24,	32	},
+	[FMT_D10]	= { 32,	0	},
 };
 
 enum value_id {
@@ -128,9 +126,14 @@ enum value_id {
 	SD24,		/* 24-bit signed displacement */
 	SIMM4_2,	/* 4-bit signed displacement in opcode bits 4-7 */
 	SIMM8,		/* 8-bit signed immediate */
+	IMM8,		/* 8-bit unsigned immediate */
+	IMM16,		/* 16-bit unsigned immediate */
 	IMM24,		/* 24-bit unsigned immediate */
 	IMM32,		/* 32-bit unsigned immediate */
-	IMM32_HIGH8,	/* 32-bit unsigned immediate, high 8-bits in opcode */
+	IMM32_HIGH8,	/* 32-bit unsigned immediate, LSB in opcode */
+
+	IMM32_MEM,	/* 32-bit unsigned displacement */
+	IMM32_HIGH8_MEM, /* 32-bit unsigned displacement, LSB in opcode */
 
 	DN0	= DM0,
 	DN1	= DM1,
@@ -149,7 +152,7 @@ enum value_id {
 };
 
 struct mn10300_opcode {
-	const char	*name;
+	const char	name[8];
 	u_int32_t	opcode;
 	u_int32_t	opmask;
 	unsigned	exclusion;
@@ -185,6 +188,10 @@ struct mn10300_opcode {
    Foundation, Inc., 59 Temple Place - Suite 330, Boston, MA 02111-1307, USA.
 */
 static const struct mn10300_opcode mn10300_opcodes[] = {
+{ "mov",	0x4200,	     0xf300,	  0,    FMT_S1, 0,	{DM1, MEM2(IMM8, SP)}},
+{ "mov",	0x4300,	     0xf300,	  0,    FMT_S1, 0,	{AM1, MEM2(IMM8, SP)}},
+{ "mov",	0x5800,	     0xfc00,	  0,    FMT_S1, 0,	{MEM2(IMM8, SP), DN0}},
+{ "mov",	0x5c00,	     0xfc00,	  0,    FMT_S1, 0,	{MEM2(IMM8, SP), AN0}},
 { "mov",	0x60,	     0xf0,	  0,    FMT_S0, 0,	{DM1, MEM(AN0)}},
 { "mov",	0x70,	     0xf0,	  0,    FMT_S0, 0,	{MEM(AM0), DN1}},
 { "mov",	0xf000,	     0xfff0,	  0,    FMT_D0, 0,	{MEM(AM0), AN1}},
@@ -197,8 +204,6 @@ static const struct mn10300_opcode mn10300_opcodes[] = {
 { "mov",	0xf81000,    0xfff000,    0,    FMT_D1, 0,	{DM1, MEM2(SD8, AN0)}},
 { "mov",	0xf82000,    0xfff000,    0,    FMT_D1, 0,	{MEM2(SD8,AM0), AN1}},
 { "mov",	0xf83000,    0xfff000,    0,    FMT_D1, 0,	{AM1, MEM2(SD8, AN0)}},
-{ "mov",	0xf8f000,    0xfffc00,    0,    FMT_D1, AM33,	{MEM2(SD8, AM0), SP}},
-{ "mov",	0xf8f400,    0xfffc00,    0,    FMT_D1, AM33,	{SP, MEM2(SD8, AN0)}},
 { "mov",	0xf90a00,    0xffff00,    0,    FMT_D6, AM33,	{MEM(RM0), RN2}},
 { "mov",	0xf91a00,    0xffff00,    0,    FMT_D6, AM33,	{RM2, MEM(RN0)}},
 { "mov",	0xf96a00,    0xffff00,    0x12, FMT_D6, AM33,	{MEMINC(RM0), RN2}},
@@ -207,24 +212,46 @@ static const struct mn10300_opcode mn10300_opcodes[] = {
 { "mov",	0xfa100000,  0xfff00000,  0,    FMT_D2, 0,	{DM1, MEM2(SD16, AN0)}},
 { "mov",	0xfa200000,  0xfff00000,  0,    FMT_D2, 0,	{MEM2(SD16, AM0), AN1}},
 { "mov",	0xfa300000,  0xfff00000,  0,    FMT_D2, 0,	{AM1, MEM2(SD16, AN0)}},
+{ "mov",	0xfa900000,  0xfff30000,  0,    FMT_D2, 0,	{AM1, MEM2(IMM16, SP)}},
+{ "mov",	0xfa910000,  0xfff30000,  0,    FMT_D2, 0,	{DM1, MEM2(IMM16, SP)}},
+{ "mov",	0xfab00000,  0xfffc0000,  0,    FMT_D2, 0,	{MEM2(IMM16, SP), AN0}},
+{ "mov",	0xfab40000,  0xfffc0000,  0,    FMT_D2, 0,	{MEM2(IMM16, SP), DN0}},
 { "mov",	0xfb0a0000,  0xffff0000,  0,    FMT_D7, AM33,	{MEM2(SD8, RM0), RN2}},
 { "mov",	0xfb1a0000,  0xffff0000,  0,    FMT_D7, AM33,	{RM2, MEM2(SD8, RN0)}},
 { "mov",	0xfb6a0000,  0xffff0000,  0x22, FMT_D7, AM33,	{MEMINC2 (RM0, SIMM8), RN2}},
 { "mov",	0xfb7a0000,  0xffff0000,  0,	FMT_D7, AM33,	{RM2, MEMINC2 (RN0, SIMM8)}},
+{ "mov",	0xfb8a0000,  0xffff0f00,  0,    FMT_D7, AM33,	{MEM2(IMM8, SP), RN2}},
 { "mov",	0xfb8e0000,  0xffff000f,  0,    FMT_D7, AM33,	{MEM2(RI, RM0), RD2}},
+{ "mov",	0xfb9a0000,  0xffff0f00,  0,    FMT_D7, AM33,	{RM2, MEM2(IMM8, SP)}},
 { "mov",	0xfb9e0000,  0xffff000f,  0,    FMT_D7, AM33,	{RD2, MEM2(RI, RN0)}},
 { "mov",	0xfc000000,  0xfff00000,  0,    FMT_D4, 0,	{MEM2(IMM32,AM0), DN1}},
 { "mov",	0xfc100000,  0xfff00000,  0,    FMT_D4, 0,	{DM1, MEM2(IMM32,AN0)}},
 { "mov",	0xfc200000,  0xfff00000,  0,    FMT_D4, 0,	{MEM2(IMM32,AM0), AN1}},
 { "mov",	0xfc300000,  0xfff00000,  0,    FMT_D4, 0,	{AM1, MEM2(IMM32,AN0)}},
+{ "mov",	0xfc800000,  0xfff30000,  0,    FMT_D4, 0,	{AM1, MEM(IMM32_MEM)}},
+{ "mov",	0xfc810000,  0xfff30000,  0,    FMT_D4, 0,	{DM1, MEM(IMM32_MEM)}},
+{ "mov",	0xfc900000,  0xfff30000,  0,    FMT_D4, 0,	{AM1, MEM2(IMM32, SP)}},
+{ "mov",	0xfc910000,  0xfff30000,  0,    FMT_D4, 0,	{DM1, MEM2(IMM32, SP)}},
+{ "mov",	0xfca00000,  0xfffc0000,  0,    FMT_D4, 0,	{MEM(IMM32_MEM), AN0}},
+{ "mov",	0xfca40000,  0xfffc0000,  0,    FMT_D4, 0,	{MEM(IMM32_MEM), DN0}},
+{ "mov",	0xfcb00000,  0xfffc0000,  0,    FMT_D4, 0,	{MEM2(IMM32, SP), AN0}},
+{ "mov",	0xfcb40000,  0xfffc0000,  0,    FMT_D4, 0,	{MEM2(IMM32, SP), DN0}},
 { "mov",	0xfd0a0000,  0xffff0000,  0,    FMT_D8, AM33,	{MEM2(SD24, RM0), RN2}},
 { "mov",	0xfd1a0000,  0xffff0000,  0,    FMT_D8, AM33,	{RM2, MEM2(SD24, RN0)}},
 { "mov",	0xfd6a0000,  0xffff0000,  0x22, FMT_D8, AM33,	{MEMINC2 (RM0, IMM24), RN2}},
 { "mov",	0xfd7a0000,  0xffff0000,  0,	FMT_D8, AM33,	{RM2, MEMINC2 (RN0, IMM24)}},
+{ "mov",	0xfd8a0000,  0xffff0f00,  0,    FMT_D8, AM33,	{MEM2(IMM24, SP), RN2}},
+{ "mov",	0xfd9a0000,  0xffff0f00,  0,    FMT_D8, AM33,	{RM2, MEM2(IMM24, SP)}},
 { "mov",	0xfe0a0000,  0xffff0000,  0,    FMT_D9, AM33,	{MEM2(IMM32_HIGH8,RM0), RN2}},
+{ "mov",	0xfe0a0000,  0xffff0000,  0,    FMT_D9, AM33,	{MEM2(IMM32_HIGH8,RM0), RN2}},
+{ "mov",	0xfe0e0000,  0xffff0f00,  0,    FMT_D9, AM33,	{MEM(IMM32_HIGH8_MEM), RN2}},
 { "mov",	0xfe1a0000,  0xffff0000,  0,    FMT_D9, AM33,	{RM2, MEM2(IMM32_HIGH8, RN0)}},
+{ "mov",	0xfe1a0000,  0xffff0000,  0,    FMT_D9, AM33,	{RM2, MEM2(IMM32_HIGH8, RN0)}},
+{ "mov",	0xfe1e0000,  0xffff0f00,  0,    FMT_D9, AM33,	{RM2, MEM(IMM32_HIGH8_MEM)}},
 { "mov",	0xfe6a0000,  0xffff0000,  0x22, FMT_D9, AM33,	{MEMINC2 (RM0, IMM32_HIGH8), RN2}},
 { "mov",	0xfe7a0000,  0xffff0000,  0,	FMT_D9, AM33,	{RN2, MEMINC2 (RM0, IMM32_HIGH8)}},
+{ "mov",	0xfe8a0000,  0xffff0f00,  0,    FMT_D9, AM33,	{MEM2(IMM32_HIGH8, SP), RN2}},
+{ "mov",	0xfe9a0000,  0xffff0f00,  0,    FMT_D9, AM33,	{RM2, MEM2(IMM32_HIGH8, SP)}},
 
 { "movhu",	0xf060,	     0xfff0,	  0,    FMT_D0, 0,	{MEM(AM0), DN1}},
 { "movhu",	0xf070,	     0xfff0,	  0,    FMT_D0, 0,	{DM1, MEM(AN0)}},
@@ -232,29 +259,58 @@ static const struct mn10300_opcode mn10300_opcodes[] = {
 { "movhu",	0xf4c0,	     0xffc0,	  0,    FMT_D0, 0,	{DM2, MEM2(DI, AN0)}},
 { "movhu",	0xf86000,    0xfff000,    0,    FMT_D1, 0,	{MEM2(SD8, AM0), DN1}},
 { "movhu",	0xf87000,    0xfff000,    0,    FMT_D1, 0,	{DM1, MEM2(SD8, AN0)}},
+{ "movhu",	0xf89300,    0xfff300,    0,    FMT_D1, 0,	{DM1, MEM2(IMM8, SP)}},
+{ "movhu",	0xf8bc00,    0xfffc00,    0,    FMT_D1, 0,	{MEM2(IMM8, SP), DN0}},
 { "movhu",	0xf94a00,    0xffff00,    0,    FMT_D6, AM33,	{MEM(RM0), RN2}},
 { "movhu",	0xf95a00,    0xffff00,    0,    FMT_D6, AM33,	{RM2, MEM(RN0)}},
 { "movhu",	0xf9ea00,    0xffff00,    0x12, FMT_D6, AM33,	{MEMINC(RM0), RN2}},
 { "movhu",	0xf9fa00,    0xffff00,    0,	FMT_D6, AM33,	{RM2, MEMINC(RN0)}},
 { "movhu",	0xfa600000,  0xfff00000,  0,    FMT_D2, 0,	{MEM2(SD16, AM0), DN1}},
 { "movhu",	0xfa700000,  0xfff00000,  0,    FMT_D2, 0,	{DM1, MEM2(SD16, AN0)}},
+{ "movhu",	0xfa930000,  0xfff30000,  0,    FMT_D2, 0,	{DM1, MEM2(IMM16, SP)}},
+{ "movhu",	0xfabc0000,  0xfffc0000,  0,    FMT_D2, 0,	{MEM2(IMM16, SP), DN0}},
 { "movhu",	0xfb4a0000,  0xffff0000,  0,    FMT_D7, AM33,	{MEM2(SD8, RM0), RN2}},
 { "movhu",	0xfb5a0000,  0xffff0000,  0,    FMT_D7, AM33,	{RM2, MEM2(SD8, RN0)}},
+{ "movhu",	0xfbca0000,  0xffff0f00,  0,    FMT_D7, AM33,	{MEM2(IMM8, SP), RN2}},
 { "movhu",	0xfbce0000,  0xffff000f,  0,    FMT_D7, AM33,	{MEM2(RI, RM0), RD2}},
+{ "movhu",	0xfbda0000,  0xffff0f00,  0,    FMT_D7, AM33,	{RM2, MEM2(IMM8, SP)}},
 { "movhu",	0xfbde0000,  0xffff000f,  0,    FMT_D7, AM33,	{RD2, MEM2(RI, RN0)}},
 { "movhu",	0xfbea0000,  0xffff0000,  0x22, FMT_D7, AM33,	{MEMINC2 (RM0, SIMM8), RN2}},
 { "movhu",	0xfbfa0000,  0xffff0000,  0,	FMT_D7, AM33,	{RM2, MEMINC2 (RN0, SIMM8)}},
 { "movhu",	0xfc600000,  0xfff00000,  0,    FMT_D4, 0,	{MEM2(IMM32,AM0), DN1}},
 { "movhu",	0xfc700000,  0xfff00000,  0,    FMT_D4, 0,	{DM1, MEM2(IMM32,AN0)}},
+{ "movhu",	0xfc830000,  0xfff30000,  0,    FMT_D4, 0,	{DM1, MEM(IMM32_MEM)}},
+{ "movhu",	0xfc930000,  0xfff30000,  0,    FMT_D4, 0,	{DM1, MEM2(IMM32, SP)}},
+{ "movhu",	0xfcac0000,  0xfffc0000,  0,    FMT_D4, 0,	{MEM(IMM32_MEM), DN0}},
+{ "movhu",	0xfcbc0000,  0xfffc0000,  0,    FMT_D4, 0,	{MEM2(IMM32, SP), DN0}},
 { "movhu",	0xfd4a0000,  0xffff0000,  0,    FMT_D8, AM33,	{MEM2(SD24, RM0), RN2}},
 { "movhu",	0xfd5a0000,  0xffff0000,  0,    FMT_D8, AM33,	{RM2, MEM2(SD24, RN0)}},
+{ "movhu",	0xfdca0000,  0xffff0f00,  0,    FMT_D8, AM33,	{MEM2(IMM24, SP), RN2}},
+{ "movhu",	0xfdda0000,  0xffff0f00,  0,    FMT_D8, AM33,	{RM2, MEM2(IMM24, SP)}},
 { "movhu",	0xfdea0000,  0xffff0000,  0x22, FMT_D8, AM33,	{MEMINC2 (RM0, IMM24), RN2}},
 { "movhu",	0xfdfa0000,  0xffff0000,  0,	FMT_D8, AM33,	{RM2, MEMINC2 (RN0, IMM24)}},
 { "movhu",	0xfe4a0000,  0xffff0000,  0,    FMT_D9, AM33,	{MEM2(IMM32_HIGH8,RM0), RN2}},
+{ "movhu",	0xfe4e0000,  0xffff0f00,  0,    FMT_D9, AM33,	{MEM(IMM32_HIGH8_MEM), RN2}},
 { "movhu",	0xfe5a0000,  0xffff0000,  0,    FMT_D9, AM33,	{RM2, MEM2(IMM32_HIGH8, RN0)}},
+{ "movhu",	0xfe5e0000,  0xffff0f00,  0,    FMT_D9, AM33,	{RM2, MEM(IMM32_HIGH8_MEM)}},
+{ "movhu",	0xfeca0000,  0xffff0f00,  0,    FMT_D9, AM33,	{MEM2(IMM32_HIGH8, SP), RN2}},
+{ "movhu",	0xfeda0000,  0xffff0f00,  0,    FMT_D9, AM33,	{RM2, MEM2(IMM32_HIGH8, SP)}},
 { "movhu",	0xfeea0000,  0xffff0000,  0x22, FMT_D9, AM33,	{MEMINC2 (RM0, IMM32_HIGH8), RN2}},
 { "movhu",	0xfefa0000,  0xffff0000,  0,	FMT_D9, AM33,	{RN2, MEMINC2 (RM0, IMM32_HIGH8)}},
-{ 0, 0, 0, 0, 0, 0, {0}},
+
+{ "mov_llt",	0xf7e00000,  0xffff000f,  0x22, FMT_D10, AM33,	 {MEMINC2 (RN4,SIMM4_2), RM6}},
+{ "mov_lgt",	0xf7e00001,  0xffff000f,  0x22, FMT_D10, AM33,	 {MEMINC2 (RN4,SIMM4_2), RM6}},
+{ "mov_lge",	0xf7e00002,  0xffff000f,  0x22, FMT_D10, AM33,	 {MEMINC2 (RN4,SIMM4_2), RM6}},
+{ "mov_lle",	0xf7e00003,  0xffff000f,  0x22, FMT_D10, AM33,	 {MEMINC2 (RN4,SIMM4_2), RM6}},
+{ "mov_lcs",	0xf7e00004,  0xffff000f,  0x22, FMT_D10, AM33,	 {MEMINC2 (RN4,SIMM4_2), RM6}},
+{ "mov_lhi",	0xf7e00005,  0xffff000f,  0x22, FMT_D10, AM33,	 {MEMINC2 (RN4,SIMM4_2), RM6}},
+{ "mov_lcc",	0xf7e00006,  0xffff000f,  0x22, FMT_D10, AM33,	 {MEMINC2 (RN4,SIMM4_2), RM6}},
+{ "mov_lls",	0xf7e00007,  0xffff000f,  0x22, FMT_D10, AM33,	 {MEMINC2 (RN4,SIMM4_2), RM6}},
+{ "mov_leq",	0xf7e00008,  0xffff000f,  0x22, FMT_D10, AM33,	 {MEMINC2 (RN4,SIMM4_2), RM6}},
+{ "mov_lne",	0xf7e00009,  0xffff000f,  0x22, FMT_D10, AM33,	 {MEMINC2 (RN4,SIMM4_2), RM6}},
+{ "mov_lra",	0xf7e0000a,  0xffff000f,  0x22, FMT_D10, AM33,	 {MEMINC2 (RN4,SIMM4_2), RM6}},
+
+{ "", 0, 0, 0, 0, 0, {0}},
 };
 
 /*
@@ -265,18 +321,21 @@ asmlinkage void misalignment(struct pt_regs *regs, enum exception_code code)
 	const struct exception_table_entry *fixup;
 	const struct mn10300_opcode *pop;
 	unsigned long *registers = (unsigned long *) regs;
-	unsigned long data, *store, *postinc;
+	unsigned long data, *store, *postinc, disp, inc, sp;
 	mm_segment_t seg;
 	siginfo_t info;
-	uint32_t opcode, disp, noc, xo, xm;
+	uint32_t opcode, noc, xo, xm;
-	uint8_t *pc, byte;
+	uint8_t *pc, byte, datasz;
 	void *address;
-	unsigned tmp, npop;
+	unsigned tmp, npop, dispsz, loop;
 
-	kdebug("MISALIGN at %lx\n", regs->pc);
+	/* we don't fix up userspace misalignment faults */
+	if (user_mode(regs))
+		goto bus_error;
 
-	if (in_interrupt())
+	sp = (unsigned long) regs + sizeof(*regs);
-		die("Misalignment trap in interrupt context", regs, code);
+
+	kdebug("==>misalignment({pc=%lx,sp=%lx})", regs->pc, sp);
 
 	if (regs->epsw & EPSW_IE)
 		asm volatile("or %0,epsw" : : "i"(EPSW_IE));
@@ -294,8 +353,8 @@ asmlinkage void misalignment(struct pt_regs *regs, enum exception_code code)
 	opcode = byte;
 	noc = 8;
 
-	for (pop = mn10300_opcodes; pop->name; pop++) {
+	for (pop = mn10300_opcodes; pop->name[0]; pop++) {
-		npop = log2(pop->opcode | pop->opmask);
+		npop = ilog2(pop->opcode | pop->opmask);
 		if (npop <= 0 || npop > 31)
 			continue;
 		npop = (npop + 8) & ~7;
@@ -328,15 +387,15 @@ asmlinkage void misalignment(struct pt_regs *regs, enum exception_code code)
 	}
 
 	/* didn't manage to find a fixup */
-	if (!user_mode(regs))
+	printk(KERN_CRIT "MISALIGN: %lx: unsupported instruction %x\n",
-		printk(KERN_CRIT "MISALIGN: %lx: unsupported instruction %x\n",
+	       regs->pc, opcode);
-		       regs->pc, opcode);
 
 failed:
 	set_fs(seg);
 	if (die_if_no_fixup("misalignment error", regs, code))
 		return;
 
+bus_error:
 	info.si_signo	= SIGBUS;
 	info.si_errno	= 0;
 	info.si_code	= BUS_ADRALN;
@@ -346,31 +405,27 @@ failed:
 
 	/* error reading opcodes */
 fetch_error:
-	if (!user_mode(regs))
+	printk(KERN_CRIT
-		printk(KERN_CRIT
+	       "MISALIGN: %p: fault whilst reading instruction data\n",
-		       "MISALIGN: %p: fault whilst reading instruction data\n",
+	       pc);
-		       pc);
 	goto failed;
 
 bad_addr_mode:
-	if (!user_mode(regs))
+	printk(KERN_CRIT
-		printk(KERN_CRIT
+	       "MISALIGN: %lx: unsupported addressing mode %x\n",
-		       "MISALIGN: %lx: unsupported addressing mode %x\n",
+	       regs->pc, opcode);
-		       regs->pc, opcode);
 	goto failed;
 
 bad_reg_mode:
-	if (!user_mode(regs))
+	printk(KERN_CRIT
-		printk(KERN_CRIT
+	       "MISALIGN: %lx: unsupported register mode %x\n",
-		       "MISALIGN: %lx: unsupported register mode %x\n",
+	       regs->pc, opcode);
-		       regs->pc, opcode);
 	goto failed;
 
 unsupported_instruction:
-	if (!user_mode(regs))
+	printk(KERN_CRIT
-		printk(KERN_CRIT
+	       "MISALIGN: %lx: unsupported instruction %x (%s)\n",
-		       "MISALIGN: %lx: unsupported instruction %x (%s)\n",
+	       regs->pc, opcode, pop->name);
-		       regs->pc, opcode, pop->name);
 	goto failed;
 
 transfer_failed:
@@ -391,7 +446,7 @@ transfer_failed:
 
 	/* we matched the opcode */
 found_opcode:
-	kdebug("MISALIGN: %lx: %x==%x { %x, %x }\n",
+	kdebug("%lx: %x==%x { %x, %x }",
 	       regs->pc, opcode, pop->opcode, pop->params[0], pop->params[1]);
 
 	tmp = format_tbl[pop->format].opsz;
@@ -406,106 +461,108 @@ found_opcode:
 
 	/* grab the extra displacement (note it's LSB first) */
 	disp = 0;
-	tmp = format_tbl[pop->format].dispsz >> 3;
+	dispsz = format_tbl[pop->format].dispsz;
-	while (tmp > 0) {
+	for (loop = 0; loop < dispsz; loop += 8) {
-		tmp--;
-		disp <<= 8;
-
 		pc++;
 		if (__get_user(byte, pc) != 0)
 			goto fetch_error;
-		disp |= byte;
+		disp |= byte << loop;
+		kdebug("{%p} disp[%02x]=%02x", pc, loop, byte);
 	}
 
+	kdebug("disp=%lx", disp);
+
 	set_fs(KERNEL_XDS);
-	if (fixup || regs->epsw & EPSW_nSL)
+	if (fixup)
 		set_fs(seg);
 
 	tmp = (pop->params[0] ^ pop->params[1]) & 0x80000000;
 	if (!tmp) {
-		if (!user_mode(regs))
+		printk(KERN_CRIT
-			printk(KERN_CRIT
+		       "MISALIGN: %lx: insn not move to/from memory %x\n",
-			       "MISALIGN: %lx:"
+		       regs->pc, opcode);
-			       " insn not move to/from memory %x\n",
-			       regs->pc, opcode);
 		goto failed;
 	}
 
+	/* determine the data transfer size of the move */
+	if (pop->name[3] == 0 || /* "mov" */
+	    pop->name[4] == 'l') /* mov_lcc */
+		inc = datasz = 4;
+	else if (pop->name[3] == 'h') /* movhu */
+		inc = datasz = 2;
+	else
+		goto unsupported_instruction;
+
 	if (pop->params[0] & 0x80000000) {
 		/* move memory to register */
-		if (!misalignment_addr(registers, pop->params[0], opcode, disp,
+		if (!misalignment_addr(registers, sp,
-				       &address, &postinc))
+				       pop->params[0], opcode, disp,
+				       &address, &postinc, &inc))
 			goto bad_addr_mode;
 
 		if (!misalignment_reg(registers, pop->params[1], opcode, disp,
 				      &store))
 			goto bad_reg_mode;
 
-		if (strcmp(pop->name, "mov") == 0) {
+		kdebug("mov%u (%p),DARn", datasz, address);
-			kdebug("FIXUP: mov (%p),DARn\n", address);
+		if (copy_from_user(&data, (void *) address, datasz) != 0)
-			if (copy_from_user(&data, (void *) address, 4) != 0)
+			goto transfer_failed;
-				goto transfer_failed;
+		if (pop->params[0] & 0x1000000) {
-			if (pop->params[0] & 0x1000000)
+			kdebug("inc=%lx", inc);
-				*postinc += 4;
+			*postinc += inc;
-		} else if (strcmp(pop->name, "movhu") == 0) {
-			kdebug("FIXUP: movhu (%p),DARn\n", address);
-			data = 0;
-			if (copy_from_user(&data, (void *) address, 2) != 0)
-				goto transfer_failed;
-			if (pop->params[0] & 0x1000000)
-				*postinc += 2;
-		} else {
-			goto unsupported_instruction;
 		}
 
 		*store = data;
+		kdebug("loaded %lx", data);
 	} else {
 		/* move register to memory */
 		if (!misalignment_reg(registers, pop->params[0], opcode, disp,
 				      &store))
 			goto bad_reg_mode;
 
-		if (!misalignment_addr(registers, pop->params[1], opcode, disp,
+		if (!misalignment_addr(registers, sp,
-				       &address, &postinc))
+				       pop->params[1], opcode, disp,
+				       &address, &postinc, &inc))
 			goto bad_addr_mode;
 
 		data = *store;
 
-		if (strcmp(pop->name, "mov") == 0) {
+		kdebug("mov%u %lx,(%p)", datasz, data, address);
-			kdebug("FIXUP: mov %lx,(%p)\n", data, address);
+		if (copy_to_user((void *) address, &data, datasz) != 0)
-			if (copy_to_user((void *) address, &data, 4) != 0)
+			goto transfer_failed;
-				goto transfer_failed;
+		if (pop->params[1] & 0x1000000)
-			if (pop->params[1] & 0x1000000)
+			*postinc += inc;
-				*postinc += 4;
-		} else if (strcmp(pop->name, "movhu") == 0) {
-			kdebug("FIXUP: movhu %hx,(%p)\n",
-			       (uint16_t) data, address);
-			if (copy_to_user((void *) address, &data, 2) != 0)
-				goto transfer_failed;
-			if (pop->params[1] & 0x1000000)
-				*postinc += 2;
-		} else {
-			goto unsupported_instruction;
-		}
 	}
 
 	tmp = format_tbl[pop->format].opsz + format_tbl[pop->format].dispsz;
 	regs->pc += tmp >> 3;
 
+	/* handle MOV_Lcc, which are currently the only FMT_D10 insns that
+	 * access memory */
+	if (pop->format == FMT_D10)
+		misalignment_MOV_Lcc(regs, opcode);
+
 	set_fs(seg);
-	return;
 }
 
 /*
  * determine the address that was being accessed
  */
-static int misalignment_addr(unsigned long *registers, unsigned params,
+static int misalignment_addr(unsigned long *registers, unsigned long sp,
-			     unsigned opcode, unsigned disp,
+			     unsigned params, unsigned opcode,
-			     void **_address, unsigned long **_postinc)
+			     unsigned long disp,
+			     void **_address, unsigned long **_postinc,
+			     unsigned long *_inc)
 {
 	unsigned long *postinc = NULL, address = 0, tmp;
 
-	params &= 0x7fffffff;
+	if (!(params & 0x1000000)) {
+		kdebug("noinc");
+		*_inc = 0;
+		_inc = NULL;
+	}
+
+	params &= 0x00ffffff;
 
 	do {
 		switch (params & 0xff) {
@@ -514,11 +571,11 @@ static int misalignment_addr(unsigned long *registers, unsigned params,
 			address += *postinc;
 			break;
 		case DM1:
-			postinc = &registers[Dreg_index[opcode >> 2 & 0x0c]];
+			postinc = &registers[Dreg_index[opcode >> 2 & 0x03]];
 			address += *postinc;
 			break;
 		case DM2:
-			postinc = &registers[Dreg_index[opcode >> 4 & 0x30]];
+			postinc = &registers[Dreg_index[opcode >> 4 & 0x03]];
 			address += *postinc;
 			break;
 		case AM0:
@@ -526,11 +583,11 @@ static int misalignment_addr(unsigned long *registers, unsigned params,
 			address += *postinc;
 			break;
 		case AM1:
-			postinc = &registers[Areg_index[opcode >> 2 & 0x0c]];
+			postinc = &registers[Areg_index[opcode >> 2 & 0x03]];
 			address += *postinc;
 			break;
 		case AM2:
-			postinc = &registers[Areg_index[opcode >> 4 & 0x30]];
+			postinc = &registers[Areg_index[opcode >> 4 & 0x03]];
 			address += *postinc;
 			break;
 		case RM0:
@@ -561,33 +618,53 @@ static int misalignment_addr(unsigned long *registers, unsigned params,
 			postinc = &registers[Rreg_index[disp >> 4 & 0x0f]];
 			address += *postinc;
 			break;
+		case SP:
+			address += sp;
+			break;
 
+			/* displacements are either to be added to the address
+			 * before use, or, in the case of post-inc addressing,
+			 * to be added into the base register after use */
 		case SD8:
 		case SIMM8:
-			address += (int32_t) (int8_t) (disp & 0xff);
+			disp = (long) (int8_t) (disp & 0xff);
-			break;
+			goto displace_or_inc;
 		case SD16:
-			address += (int32_t) (int16_t) (disp & 0xffff);
+			disp = (long) (int16_t) (disp & 0xffff);
-			break;
+			goto displace_or_inc;
 		case SD24:
 			tmp = disp << 8;
 			asm("asr 8,%0" : "=r"(tmp) : "0"(tmp));
-			address += tmp;
+			disp = (long) tmp;
-			break;
+			goto displace_or_inc;
 		case SIMM4_2:
 			tmp = opcode >> 4 & 0x0f;
 			tmp <<= 28;
 			asm("asr 28,%0" : "=r"(tmp) : "0"(tmp));
-			address += tmp;
+			disp = (long) tmp;
-			break;
+			goto displace_or_inc;
+		case IMM8:
+			disp &= 0x000000ff;
+			goto displace_or_inc;
+		case IMM16:
+			disp &= 0x0000ffff;
+			goto displace_or_inc;
 		case IMM24:
-			address += disp & 0x00ffffff;
+			disp &= 0x00ffffff;
-			break;
+			goto displace_or_inc;
 		case IMM32:
+		case IMM32_MEM:
 		case IMM32_HIGH8:
-			address += disp;
+		case IMM32_HIGH8_MEM:
+		displace_or_inc:
+			kdebug("%s %lx", _inc ? "incr" : "disp", disp);
+			if (!_inc)
+				address += disp;
+			else
+				*_inc = disp;
 			break;
 		default:
+			BUG();
 			return 0;
 		}
 	} while ((params >>= 8));
@@ -601,7 +678,7 @@ static int misalignment_addr(unsigned long *registers, unsigned params,
  * determine the register that is acting as source/dest
  */
 static int misalignment_reg(unsigned long *registers, unsigned params,
-			    unsigned opcode, unsigned disp,
+			    unsigned opcode, unsigned long disp,
 			    unsigned long **_register)
 {
 	params &= 0x7fffffff;
@@ -654,8 +731,239 @@ static int misalignment_reg(unsigned long *registers, unsigned params,
 		break;
 
 	default:
+		BUG();
 		return 0;
 	}
 
 	return 1;
 }
+
+/*
+ * handle the conditional loop part of the move-and-loop instructions
+ */
+static void misalignment_MOV_Lcc(struct pt_regs *regs, uint32_t opcode)
+{
+	unsigned long epsw = regs->epsw;
+	unsigned long NxorV;
+
+	kdebug("MOV_Lcc %x [flags=%lx]", opcode, epsw & 0xf);
+
+	/* calculate N^V and shift onto the same bit position as Z */
+	NxorV = ((epsw >> 3) ^ epsw >> 1) & 1;
+
+	switch (opcode & 0xf) {
+	case 0x0: /* MOV_LLT: N^V */
+		if (NxorV)
+			goto take_the_loop;
+		return;
+	case 0x1: /* MOV_LGT: ~(Z or (N^V))*/
+		if (!((epsw & EPSW_FLAG_Z) | NxorV))
+			goto take_the_loop;
+		return;
+	case 0x2: /* MOV_LGE: ~(N^V) */
+		if (!NxorV)
+			goto take_the_loop;
+		return;
+	case 0x3: /* MOV_LLE: Z or (N^V) */
+		if ((epsw & EPSW_FLAG_Z) | NxorV)
+			goto take_the_loop;
+		return;
+
+	case 0x4: /* MOV_LCS: C */
+		if (epsw & EPSW_FLAG_C)
+			goto take_the_loop;
+		return;
+	case 0x5: /* MOV_LHI: ~(C or Z) */
+		if (!(epsw & (EPSW_FLAG_C | EPSW_FLAG_Z)))
+			goto take_the_loop;
+		return;
+	case 0x6: /* MOV_LCC: ~C */
+		if (!(epsw & EPSW_FLAG_C))
+			goto take_the_loop;
+		return;
+	case 0x7: /* MOV_LLS: C or Z */
+		if (epsw & (EPSW_FLAG_C | EPSW_FLAG_Z))
+			goto take_the_loop;
+		return;
+
+	case 0x8: /* MOV_LEQ: Z */
+		if (epsw & EPSW_FLAG_Z)
+			goto take_the_loop;
+		return;
+	case 0x9: /* MOV_LNE: ~Z */
+		if (!(epsw & EPSW_FLAG_Z))
+			goto take_the_loop;
+		return;
+	case 0xa: /* MOV_LRA: always */
+		goto take_the_loop;
+
+	default:
+		BUG();
+	}
+
+take_the_loop:
+	/* wind the PC back to just after the SETLB insn */
+	kdebug("loop LAR=%lx", regs->lar);
+	regs->pc = regs->lar - 4;
+}
+
+/*
+ * misalignment handler tests
+ */
+#ifdef CONFIG_TEST_MISALIGNMENT_HANDLER
+static u8 __initdata testbuf[512] __attribute__((aligned(16))) = {
+	[257] = 0x11,
+	[258] = 0x22,
+	[259] = 0x33,
+	[260] = 0x44,
+};
+
+#define ASSERTCMP(X, OP, Y)						\
+do {									\
+	if (unlikely(!((X) OP (Y)))) {					\
+		printk(KERN_ERR "\n");					\
+		printk(KERN_ERR "MISALIGN: Assertion failed at line %u\n", \
+		       __LINE__);					\
+		printk(KERN_ERR "0x%lx " #OP " 0x%lx is false\n",	\
+		       (unsigned long)(X), (unsigned long)(Y));		\
+		BUG();							\
+	}								\
+} while(0)
+
+static int __init test_misalignment(void)
+{
+	register void *r asm("e0");
+	register u32 y asm("e1");
+	void *p = testbuf, *q;
+	u32 tmp, tmp2, x;
+
+	printk(KERN_NOTICE "==>test_misalignment() [testbuf=%p]\n", p);
+	p++;
+
+	printk(KERN_NOTICE "___ MOV (Am),Dn ___\n");
+	q = p + 256;
+	asm volatile("mov	(%0),%1" : "+a"(q), "=d"(x));
+	ASSERTCMP(q, ==, p + 256);
+	ASSERTCMP(x, ==, 0x44332211);
+
+	printk(KERN_NOTICE "___ MOV (256,Am),Dn ___\n");
+	q = p;
+	asm volatile("mov	(256,%0),%1" : "+a"(q), "=d"(x));
+	ASSERTCMP(q, ==, p);
+	ASSERTCMP(x, ==, 0x44332211);
+
+	printk(KERN_NOTICE "___ MOV (Di,Am),Dn ___\n");
+	tmp = 256;
+	q = p;
+	asm volatile("mov	(%2,%0),%1" : "+a"(q), "=d"(x), "+d"(tmp));
+	ASSERTCMP(q, ==, p);
+	ASSERTCMP(x, ==, 0x44332211);
+	ASSERTCMP(tmp, ==, 256);
+
+	printk(KERN_NOTICE "___ MOV (256,Rm),Rn ___\n");
+	r = p;
+	asm volatile("mov	(256,%0),%1" : "+r"(r), "=r"(y));
+	ASSERTCMP(r, ==, p);
+	ASSERTCMP(y, ==, 0x44332211);
+
+	printk(KERN_NOTICE "___ MOV (Rm+),Rn ___\n");
+	r = p + 256;
+	asm volatile("mov	(%0+),%1" : "+r"(r), "=r"(y));
+	ASSERTCMP(r, ==, p + 256 + 4);
+	ASSERTCMP(y, ==, 0x44332211);
+
+	printk(KERN_NOTICE "___ MOV (Rm+,8),Rn ___\n");
+	r = p + 256;
+	asm volatile("mov	(%0+,8),%1" : "+r"(r), "=r"(y));
+	ASSERTCMP(r, ==, p + 256 + 8);
+	ASSERTCMP(y, ==, 0x44332211);
+
+	printk(KERN_NOTICE "___ MOV (7,SP),Rn ___\n");
+	asm volatile(
+		"add	-16,sp		\n"
+		"mov	+0x11,%0	\n"
+		"movbu	%0,(7,sp)	\n"
+		"mov	+0x22,%0	\n"
+		"movbu	%0,(8,sp)	\n"
+		"mov	+0x33,%0	\n"
+		"movbu	%0,(9,sp)	\n"
+		"mov	+0x44,%0	\n"
+		"movbu	%0,(10,sp)	\n"
+		"mov	(7,sp),%1	\n"
+		"add	+16,sp		\n"
+		: "+a"(q), "=d"(x));
+	ASSERTCMP(x, ==, 0x44332211);
+
+	printk(KERN_NOTICE "___ MOV (259,SP),Rn ___\n");
+	asm volatile(
+		"add	-264,sp		\n"
+		"mov	+0x11,%0	\n"
+		"movbu	%0,(259,sp)	\n"
+		"mov	+0x22,%0	\n"
+		"movbu	%0,(260,sp)	\n"
+		"mov	+0x33,%0	\n"
+		"movbu	%0,(261,sp)	\n"
+		"mov	+0x55,%0	\n"
+		"movbu	%0,(262,sp)	\n"
+		"mov	(259,sp),%1	\n"
+		"add	+264,sp		\n"
+		: "+d"(tmp), "=d"(x));
+	ASSERTCMP(x, ==, 0x55332211);
+
+	printk(KERN_NOTICE "___ MOV (260,SP),Rn ___\n");
+	asm volatile(
+		"add	-264,sp		\n"
+		"mov	+0x11,%0	\n"
+		"movbu	%0,(260,sp)	\n"
+		"mov	+0x22,%0	\n"
+		"movbu	%0,(261,sp)	\n"
+		"mov	+0x33,%0	\n"
+		"movbu	%0,(262,sp)	\n"
+		"mov	+0x55,%0	\n"
+		"movbu	%0,(263,sp)	\n"
+		"mov	(260,sp),%1	\n"
+		"add	+264,sp		\n"
+		: "+d"(tmp), "=d"(x));
+	ASSERTCMP(x, ==, 0x55332211);
+
+
+	printk(KERN_NOTICE "___ MOV_LNE ___\n");
+	tmp = 1;
+	tmp2 = 2;
+	q = p + 256;
+	asm volatile(
+		"setlb			\n"
+		"mov	%2,%3		\n"
+		"mov	%1,%2		\n"
+		"cmp	+0,%1		\n"
+		"mov_lne	(%0+,4),%1"
+		: "+r"(q), "+d"(tmp), "+d"(tmp2), "=d"(x)
+		:
+		: "cc");
+	ASSERTCMP(q, ==, p + 256 + 12);
+	ASSERTCMP(x, ==, 0x44332211);
+
+	printk(KERN_NOTICE "___ MOV in SETLB ___\n");
+	tmp = 1;
+	tmp2 = 2;
+	q = p + 256;
+	asm volatile(
+		"setlb			\n"
+		"mov	%1,%3		\n"
+		"mov	(%0+),%1	\n"
+		"cmp	+0,%1		\n"
+		"lne			"
+		: "+a"(q), "+d"(tmp), "+d"(tmp2), "=d"(x)
+		:
+		: "cc");
+
+	ASSERTCMP(q, ==, p + 256 + 8);
+	ASSERTCMP(x, ==, 0x44332211);
+
+	printk(KERN_NOTICE "<==test_misalignment()\n");
+	return 0;
+}
+
+arch_initcall(test_misalignment);
+
+#endif /* CONFIG_TEST_MISALIGNMENT_HANDLER */

arch/parisc/include/asm/smp.h

@@ -44,8 +44,6 @@ extern void arch_send_call_function_ipi(cpumask_t mask);
  
 #define PROC_CHANGE_PENALTY	15		/* Schedule penalty */
 
-extern unsigned long cpu_present_mask;
-
 #define raw_smp_processor_id()	(current_thread_info()->cpu)
 
 #else /* CONFIG_SMP */

arch/s390/kernel/entry.S

@@ -61,22 +61,25 @@ STACK_SIZE  = 1 << STACK_SHIFT
 
 #ifdef CONFIG_TRACE_IRQFLAGS
 	.macro	TRACE_IRQS_ON
-	l	%r1,BASED(.Ltrace_irq_on)
+	basr	%r2,%r0
+	l	%r1,BASED(.Ltrace_irq_on_caller)
 	basr	%r14,%r1
 	.endm
 
 	.macro	TRACE_IRQS_OFF
-	l	%r1,BASED(.Ltrace_irq_off)
+	basr	%r2,%r0
+	l	%r1,BASED(.Ltrace_irq_off_caller)
 	basr	%r14,%r1
 	.endm
 
 	.macro	TRACE_IRQS_CHECK
+	basr	%r2,%r0
 	tm	SP_PSW(%r15),0x03	# irqs enabled?
 	jz	0f
-	l	%r1,BASED(.Ltrace_irq_on)
+	l	%r1,BASED(.Ltrace_irq_on_caller)
 	basr	%r14,%r1
 	j	1f
-0:	l	%r1,BASED(.Ltrace_irq_off)
+0:	l	%r1,BASED(.Ltrace_irq_off_caller)
 	basr	%r14,%r1
 1:
 	.endm
@@ -1113,9 +1116,12 @@ cleanup_io_leave_insn:
 .Lschedtail:	.long	schedule_tail
 .Lsysc_table:	.long	sys_call_table
 #ifdef CONFIG_TRACE_IRQFLAGS
-.Ltrace_irq_on: .long	trace_hardirqs_on
+.Ltrace_irq_on_caller:
-.Ltrace_irq_off:
+		.long	trace_hardirqs_on_caller
-		.long	trace_hardirqs_off
+.Ltrace_irq_off_caller:
+		.long	trace_hardirqs_off_caller
+#endif
+#ifdef CONFIG_LOCKDEP
 .Llockdep_sys_exit:
 		.long	lockdep_sys_exit
 #endif

arch/s390/kernel/entry64.S

@@ -61,19 +61,22 @@ _TIF_WORK_INT = (_TIF_SIGPENDING | _TIF_NOTIFY_RESUME | _TIF_NEED_RESCHED | \
 
 #ifdef CONFIG_TRACE_IRQFLAGS
 	.macro	TRACE_IRQS_ON
-	 brasl	%r14,trace_hardirqs_on
+	 basr	%r2,%r0
+	 brasl	%r14,trace_hardirqs_on_caller
 	.endm
 
 	.macro	TRACE_IRQS_OFF
-	 brasl	%r14,trace_hardirqs_off
+	 basr	%r2,%r0
+	 brasl	%r14,trace_hardirqs_off_caller
 	.endm
 
 	.macro TRACE_IRQS_CHECK
+	basr	%r2,%r0
 	tm	SP_PSW(%r15),0x03	# irqs enabled?
 	jz	0f
-	brasl	%r14,trace_hardirqs_on
+	brasl	%r14,trace_hardirqs_on_caller
 	j	1f
-0:	brasl	%r14,trace_hardirqs_off
+0:	brasl	%r14,trace_hardirqs_off_caller
 1:
 	.endm
 #else

arch/s390/kernel/process.c

@@ -136,9 +136,12 @@ static void default_idle(void)
 		return;
 	}
 	trace_hardirqs_on();
+	/* Don't trace preempt off for idle. */
+	stop_critical_timings();
 	/* Wait for external, I/O or machine check interrupt. */
 	__load_psw_mask(psw_kernel_bits | PSW_MASK_WAIT |
 			PSW_MASK_IO | PSW_MASK_EXT);
+	start_critical_timings();
 }
 
 void cpu_idle(void)

arch/s390/kernel/setup.c

@@ -604,13 +604,13 @@ setup_memory(void)
 		if (memory_chunk[i].type != CHUNK_READ_WRITE)
 			continue;
 		start_chunk = PFN_DOWN(memory_chunk[i].addr);
-		end_chunk = start_chunk + PFN_DOWN(memory_chunk[i].size) - 1;
+		end_chunk = start_chunk + PFN_DOWN(memory_chunk[i].size);
 		end_chunk = min(end_chunk, end_pfn);
 		if (start_chunk >= end_chunk)
 			continue;
 		add_active_range(0, start_chunk, end_chunk);
 		pfn = max(start_chunk, start_pfn);
-		for (; pfn <= end_chunk; pfn++)
+		for (; pfn < end_chunk; pfn++)
 			page_set_storage_key(PFN_PHYS(pfn), PAGE_DEFAULT_KEY);
 	}
 

arch/s390/kernel/sys_s390.c

@@ -198,7 +198,7 @@ asmlinkage long s390x_newuname(struct new_utsname __user *name)
 {
 	int ret = sys_newuname(name);
 
-	if (current->personality == PER_LINUX32 && !ret) {
+	if (personality(current->personality) == PER_LINUX32 && !ret) {
 		ret = copy_to_user(name->machine, "s390\0\0\0\0", 8);
 		if (ret) ret = -EFAULT;
 	}

arch/s390/kernel/topology.c

@@ -65,18 +65,21 @@ static int machine_has_topology_irq;
 static struct timer_list topology_timer;
 static void set_topology_timer(void);
 static DECLARE_WORK(topology_work, topology_work_fn);
+/* topology_lock protects the core linked list */
+static DEFINE_SPINLOCK(topology_lock);
 
 cpumask_t cpu_core_map[NR_CPUS];
 
 cpumask_t cpu_coregroup_map(unsigned int cpu)
 {
 	struct core_info *core = &core_info;
+	unsigned long flags;
 	cpumask_t mask;
 
 	cpus_clear(mask);
 	if (!machine_has_topology)
 		return cpu_present_map;
-	mutex_lock(&smp_cpu_state_mutex);
+	spin_lock_irqsave(&topology_lock, flags);
 	while (core) {
 		if (cpu_isset(cpu, core->mask)) {
 			mask = core->mask;
@@ -84,7 +87,7 @@ cpumask_t cpu_coregroup_map(unsigned int cpu)
 		}
 		core = core->next;
 	}
-	mutex_unlock(&smp_cpu_state_mutex);
+	spin_unlock_irqrestore(&topology_lock, flags);
 	if (cpus_empty(mask))
 		mask = cpumask_of_cpu(cpu);
 	return mask;
@@ -133,7 +136,7 @@ static void tl_to_cores(struct tl_info *info)
 	union tl_entry *tle, *end;
 	struct core_info *core = &core_info;
 
-	mutex_lock(&smp_cpu_state_mutex);
+	spin_lock_irq(&topology_lock);
 	clear_cores();
 	tle = info->tle;
 	end = (union tl_entry *)((unsigned long)info + info->length);
@@ -157,7 +160,7 @@ static void tl_to_cores(struct tl_info *info)
 		}
 		tle = next_tle(tle);
 	}
-	mutex_unlock(&smp_cpu_state_mutex);
+	spin_unlock_irq(&topology_lock);
 }
 
 static void topology_update_polarization_simple(void)

arch/sh/include/asm/io.h

@@ -293,6 +293,10 @@ __ioremap_mode(unsigned long offset, unsigned long size, unsigned long flags)
  */
 #define xlate_dev_kmem_ptr(p)	p
 
+#define ARCH_HAS_VALID_PHYS_ADDR_RANGE
+int valid_phys_addr_range(unsigned long addr, size_t size);
+int valid_mmap_phys_addr_range(unsigned long pfn, size_t size);
+
 #endif /* __KERNEL__ */
 
 #endif /* __ASM_SH_IO_H */

arch/sh/include/asm/pgtable.h

@@ -148,6 +148,12 @@ extern void paging_init(void);
 extern void page_table_range_init(unsigned long start, unsigned long end,
 				  pgd_t *pgd);
 
+#if !defined(CONFIG_CACHE_OFF) && defined(CONFIG_CPU_SH4) && defined(CONFIG_MMU)
+extern void kmap_coherent_init(void);
+#else
+#define kmap_coherent_init()	do { } while (0)
+#endif
+
 #include <asm-generic/pgtable.h>
 
 #endif /* __ASM_SH_PGTABLE_H */

arch/sh/kernel/cpu/sh4a/setup-sh7723.c

@@ -119,17 +119,17 @@ static struct plat_sci_port sci_platform_data[] = {
 	},{
 		.mapbase	= 0xa4e30000,
 		.flags		= UPF_BOOT_AUTOCONF,
-		.type		= PORT_SCI,
+		.type		= PORT_SCIFA,
 		.irqs		= { 56, 56, 56, 56 },
 	},{
 		.mapbase	= 0xa4e40000,
 		.flags		= UPF_BOOT_AUTOCONF,
-		.type		= PORT_SCI,
+		.type		= PORT_SCIFA,
 		.irqs		= { 88, 88, 88, 88 },
 	},{
 		.mapbase	= 0xa4e50000,
 		.flags		= UPF_BOOT_AUTOCONF,
-		.type		= PORT_SCI,
+		.type		= PORT_SCIFA,
 		.irqs		= { 109, 109, 109, 109 },
 	}, {
 		.flags = 0,

arch/sh/kernel/early_printk.c

@@ -75,6 +75,7 @@ static struct console bios_console = {
 #endif
 
 static struct uart_port scif_port = {
+	.type		= PORT_SCIF,
 	.mapbase	= CONFIG_EARLY_SCIF_CONSOLE_PORT,
 	.membase	= (char __iomem *)CONFIG_EARLY_SCIF_CONSOLE_PORT,
 };
@@ -84,9 +85,9 @@ static void scif_sercon_putc(int c)
 	while (((sci_in(&scif_port, SCFDR) & EPK_FIFO_BITS) >= EPK_FIFO_SIZE))
 		;
 
-	sci_out(&scif_port, SCxTDR, c);
 	sci_in(&scif_port, SCxSR);
 	sci_out(&scif_port, SCxSR, 0xf3 & ~(0x20 | 0x40));
+	sci_out(&scif_port, SCxTDR, c);
 
 	while ((sci_in(&scif_port, SCxSR) & 0x40) == 0)
 		;

arch/sh/kernel/timers/timer-tmu.c

@@ -120,7 +120,7 @@ static void tmu_set_mode(enum clock_event_mode mode,
 {
 	switch (mode) {
 	case CLOCK_EVT_MODE_PERIODIC:
-		ctrl_outl(ctrl_inl(TMU0_TCNT), TMU0_TCOR);
+		ctrl_outl(tmu_latest_interval[TMU0], TMU0_TCOR);
 		break;
 	case CLOCK_EVT_MODE_ONESHOT:
 		ctrl_outl(0, TMU0_TCOR);

arch/sh/lib/copy_page.S

@@ -80,6 +80,11 @@ ENTRY(copy_page)
 	.section __ex_table, "a";	\
 	.long 9999b, 6000f	;	\
 	.previous
+#define EX_NO_POP(...)			\
+	9999: __VA_ARGS__ ;		\
+	.section __ex_table, "a";	\
+	.long 9999b, 6005f	;	\
+	.previous
 ENTRY(__copy_user)
 	! Check if small number of bytes
 	mov	#11,r0
@@ -139,9 +144,9 @@ EX(	mov.b	r1,@r4		)
 	bt	1f
 
 2:
-EX(	mov.b	@r5+,r0		)
+EX_NO_POP(	mov.b	@r5+,r0		)
 	dt	r6
-EX(	mov.b	r0,@r4		)
+EX_NO_POP(	mov.b	r0,@r4		)
 	bf/s	2b
 	 add	#1,r4
 
@@ -150,7 +155,7 @@ EX(	mov.b	r0,@r4		)
 
 # Exception handler:
 .section .fixup, "ax"
-6000:
+6005:
 	mov.l	8000f,r1
 	mov	r3,r0
 	jmp	@r1

arch/sh/mm/Makefile_32

@@ -2,7 +2,7 @@
 # Makefile for the Linux SuperH-specific parts of the memory manager.
 #
 
-obj-y			:= init.o extable_32.o consistent.o
+obj-y			:= init.o extable_32.o consistent.o mmap.o
 
 ifndef CONFIG_CACHE_OFF
 cache-$(CONFIG_CPU_SH2)		:= cache-sh2.o

arch/sh/mm/Makefile_64

@@ -2,7 +2,7 @@
 # Makefile for the Linux SuperH-specific parts of the memory manager.
 #
 
-obj-y			:= init.o consistent.o
+obj-y			:= init.o consistent.o mmap.o
 
 mmu-y			:= tlb-nommu.o pg-nommu.o extable_32.o
 mmu-$(CONFIG_MMU)	:= fault_64.o ioremap_64.o tlbflush_64.o tlb-sh5.o \

arch/sh/mm/init.c

@@ -137,6 +137,7 @@ void __init page_table_range_init(unsigned long start, unsigned long end,
 void __init paging_init(void)
 {
 	unsigned long max_zone_pfns[MAX_NR_ZONES];
+	unsigned long vaddr;
 	int nid;
 
 	/* We don't need to map the kernel through the TLB, as
@@ -148,10 +149,15 @@ void __init paging_init(void)
 	 * check for a null value. */
 	set_TTB(swapper_pg_dir);
 
-	/* Populate the relevant portions of swapper_pg_dir so that
+	/*
+	 * Populate the relevant portions of swapper_pg_dir so that
 	 * we can use the fixmap entries without calling kmalloc.
-	 * pte's will be filled in by __set_fixmap(). */
+	 * pte's will be filled in by __set_fixmap().
-	page_table_range_init(FIXADDR_START, FIXADDR_TOP, swapper_pg_dir);
+	 */
+	vaddr = __fix_to_virt(__end_of_fixed_addresses - 1) & PMD_MASK;
+	page_table_range_init(vaddr, 0, swapper_pg_dir);
+
+	kmap_coherent_init();
 
 	memset(max_zone_pfns, 0, sizeof(max_zone_pfns));
 

arch/sh/mm/mmap.c

@@ -0,0 +1,31 @@
+/*
+ * arch/sh/mm/mmap.c
+ *
+ * Copyright (C) 2008  Paul Mundt
+ *
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ */
+#include <linux/io.h>
+#include <linux/mm.h>
+#include <asm/page.h>
+
+/*
+ * You really shouldn't be using read() or write() on /dev/mem.  This
+ * might go away in the future.
+ */
+int valid_phys_addr_range(unsigned long addr, size_t count)
+{
+	if (addr < __MEMORY_START)
+		return 0;
+	if (addr + count > __pa(high_memory))
+		return 0;
+
+	return 1;
+}
+
+int valid_mmap_phys_addr_range(unsigned long pfn, size_t size)
+{
+	return 1;
+}

arch/sh/mm/pg-sh4.c

@@ -7,6 +7,7 @@
  * Released under the terms of the GNU GPL v2.0.
  */
 #include <linux/mm.h>
+#include <linux/init.h>
 #include <linux/mutex.h>
 #include <linux/fs.h>
 #include <linux/highmem.h>
@@ -16,6 +17,20 @@
 
 #define CACHE_ALIAS (current_cpu_data.dcache.alias_mask)
 
+#define kmap_get_fixmap_pte(vaddr)                                     \
+	pte_offset_kernel(pmd_offset(pud_offset(pgd_offset_k(vaddr), (vaddr)), (vaddr)), (vaddr))
+
+static pte_t *kmap_coherent_pte;
+
+void __init kmap_coherent_init(void)
+{
+	unsigned long vaddr;
+
+	/* cache the first coherent kmap pte */
+	vaddr = __fix_to_virt(FIX_CMAP_BEGIN);
+	kmap_coherent_pte = kmap_get_fixmap_pte(vaddr);
+}
+
 static inline void *kmap_coherent(struct page *page, unsigned long addr)
 {
 	enum fixed_addresses idx;
@@ -34,6 +49,8 @@ static inline void *kmap_coherent(struct page *page, unsigned long addr)
 
 	update_mmu_cache(NULL, vaddr, pte);
 
+	set_pte(kmap_coherent_pte - (FIX_CMAP_END - idx), pte);
+
 	return (void *)vaddr;
 }
 

arch/sparc/include/asm/termbits.h

@@ -29,10 +29,11 @@ struct termios {
 	tcflag_t c_cflag;		/* control mode flags */
 	tcflag_t c_lflag;		/* local mode flags */
 	cc_t c_line;			/* line discipline */
+#ifndef __KERNEL__
 	cc_t c_cc[NCCS];		/* control characters */
-#ifdef __KERNEL__
+#else
+	cc_t c_cc[NCCS+2];	/* kernel needs 2 more to hold vmin/vtime */
 #define SIZEOF_USER_TERMIOS sizeof (struct termios) - (2*sizeof (cc_t))
-	cc_t _x_cc[2];                  /* We need them to hold vmin/vtime */
 #endif
 };
 
@@ -42,8 +43,7 @@ struct termios2 {
 	tcflag_t c_cflag;		/* control mode flags */
 	tcflag_t c_lflag;		/* local mode flags */
 	cc_t c_line;			/* line discipline */
-	cc_t c_cc[NCCS];		/* control characters */
+	cc_t c_cc[NCCS+2];		/* control characters */
-	cc_t _x_cc[2];                  /* padding to match ktermios */
 	speed_t c_ispeed;		/* input speed */
 	speed_t c_ospeed;		/* output speed */
 };
@@ -54,8 +54,7 @@ struct ktermios {
 	tcflag_t c_cflag;		/* control mode flags */
 	tcflag_t c_lflag;		/* local mode flags */
 	cc_t c_line;			/* line discipline */
-	cc_t c_cc[NCCS];		/* control characters */
+	cc_t c_cc[NCCS+2];		/* control characters */
-	cc_t _x_cc[2];                  /* We need them to hold vmin/vtime */
 	speed_t c_ispeed;		/* input speed */
 	speed_t c_ospeed;		/* output speed */
 };

arch/sparc/kernel/of_device.c

@@ -563,9 +563,9 @@ build_resources:
 	op->dev.parent = parent;
 	op->dev.bus = &of_platform_bus_type;
 	if (!parent)
-		strcpy(op->dev.bus_id, "root");
+		dev_set_name(&op->dev, "root");
 	else
-		sprintf(op->dev.bus_id, "%08x", dp->node);
+		dev_set_name(&op->dev, "%08x", dp->node);
 
 	if (of_device_register(op)) {
 		printk("%s: Could not register of device.\n",

arch/x86/include/asm/acpi.h

@@ -113,7 +113,6 @@ static inline void acpi_disable_pci(void)
 	acpi_pci_disabled = 1;
 	acpi_noirq_set();
 }
-extern int acpi_irq_balance_set(char *str);
 
 /* routines for saving/restoring kernel state */
 extern int acpi_save_state_mem(void);

arch/x86/include/asm/iommu.h

@@ -6,7 +6,6 @@ extern void no_iommu_init(void);
 extern struct dma_mapping_ops nommu_dma_ops;
 extern int force_iommu, no_iommu;
 extern int iommu_detected;
-extern int dmar_disabled;
 
 extern unsigned long iommu_nr_pages(unsigned long addr, unsigned long len);
 

arch/x86/kernel/acpi/boot.c

@@ -1343,7 +1343,6 @@ static void __init acpi_process_madt(void)
 			error = acpi_parse_madt_ioapic_entries();
 			if (!error) {
 				acpi_irq_model = ACPI_IRQ_MODEL_IOAPIC;
-				acpi_irq_balance_set(NULL);
 				acpi_ioapic = 1;
 
 				smp_found_config = 1;

arch/x86/kernel/early-quirks.c

@@ -188,20 +188,6 @@ static void __init ati_bugs_contd(int num, int slot, int func)
 }
 #endif
 
-#ifdef CONFIG_DMAR
-static void __init intel_g33_dmar(int num, int slot, int func)
-{
-	struct acpi_table_header *dmar_tbl;
-	acpi_status status;
-
-	status = acpi_get_table(ACPI_SIG_DMAR, 0, &dmar_tbl);
-	if (ACPI_SUCCESS(status)) {
-		printk(KERN_INFO "BIOS BUG: DMAR advertised on Intel G31/G33 chipset -- ignoring\n");
-		dmar_disabled = 1;
-	}
-}
-#endif
-
 #define QFLAG_APPLY_ONCE 	0x1
 #define QFLAG_APPLIED		0x2
 #define QFLAG_DONE		(QFLAG_APPLY_ONCE|QFLAG_APPLIED)
@@ -225,10 +211,6 @@ static struct chipset early_qrk[] __initdata = {
 	  PCI_CLASS_SERIAL_SMBUS, PCI_ANY_ID, 0, ati_bugs },
 	{ PCI_VENDOR_ID_ATI, PCI_DEVICE_ID_ATI_SBX00_SMBUS,
 	  PCI_CLASS_SERIAL_SMBUS, PCI_ANY_ID, 0, ati_bugs_contd },
-#ifdef CONFIG_DMAR
-	{ PCI_VENDOR_ID_INTEL, 0x29c0,
-	  PCI_CLASS_BRIDGE_HOST, PCI_ANY_ID, 0, intel_g33_dmar },
-#endif
 	{}
 };
 

arch/x86/kernel/kvmclock.c

@@ -128,7 +128,7 @@ static int kvm_register_clock(char *txt)
 }
 
 #ifdef CONFIG_X86_LOCAL_APIC
-static void kvm_setup_secondary_clock(void)
+static void __devinit kvm_setup_secondary_clock(void)
 {
 	/*
 	 * Now that the first cpu already had this clocksource initialized,

arch/x86/kvm/Kconfig

@@ -20,6 +20,8 @@ if VIRTUALIZATION
 config KVM
 	tristate "Kernel-based Virtual Machine (KVM) support"
 	depends on HAVE_KVM
+	# for device assignment:
+	depends on PCI
 	select PREEMPT_NOTIFIERS
 	select MMU_NOTIFIER
 	select ANON_INODES

arch/x86/kvm/i8254.c

@@ -548,8 +548,10 @@ struct kvm_pit *kvm_create_pit(struct kvm *kvm)
 	mutex_lock(&kvm->lock);
 	pit->irq_source_id = kvm_request_irq_source_id(kvm);
 	mutex_unlock(&kvm->lock);
-	if (pit->irq_source_id < 0)
+	if (pit->irq_source_id < 0) {
+		kfree(pit);
 		return NULL;
+	}
 
 	mutex_init(&pit->pit_state.lock);
 	mutex_lock(&pit->pit_state.lock);