Merge branch 'next' into for-linus
Prepare input updates for 5.2 merge window.
This commit is contained in:
Dmitry Torokhov
commit
14e0c7317e
|
|
@ -0,0 +1,37 @@
|
|||
# SPDX-License-Identifier: GPL-2.0
|
||||
%YAML 1.2
|
||||
---
|
||||
$id: http://devicetree.org/schemas/bindings/input/gpio-vibrator.yaml#
|
||||
$schema: http://devicetree.org/meta-schemas/core.yaml#
|
||||
|
||||
title: GPIO vibrator
|
||||
|
||||
maintainers:
|
||||
- Luca Weiss <luca@z3ntu.xyz>
|
||||
|
||||
description: |+
|
||||
Registers a GPIO device as vibrator, where the on/off capability is controlled by a GPIO.
|
||||
|
||||
properties:
|
||||
compatible:
|
||||
const: gpio-vibrator
|
||||
|
||||
enable-gpios:
|
||||
maxItems: 1
|
||||
|
||||
vcc-supply:
|
||||
description: Regulator that provides power
|
||||
|
||||
required:
|
||||
- compatible
|
||||
- enable-gpios
|
||||
|
||||
examples:
|
||||
- |
|
||||
#include <dt-bindings/gpio/gpio.h>
|
||||
|
||||
vibrator {
|
||||
compatible = "gpio-vibrator";
|
||||
enable-gpios = <&msmgpio 86 GPIO_ACTIVE_HIGH>;
|
||||
vcc-supply = <&pm8941_l18>;
|
||||
};
|
||||
|
|
@ -8,6 +8,7 @@ Required Properties:
|
|||
- reg: Physical base address of the controller and length of memory mapped
|
||||
region.
|
||||
- interrupts: The interrupt number to the cpu.
|
||||
- clocks: phandle to clock controller plus clock-specifier pair
|
||||
- nxp,debounce-delay-ms: Debounce delay in ms
|
||||
- nxp,scan-delay-ms: Repeated scan period in ms
|
||||
- linux,keymap: the key-code to be reported when the key is pressed
|
||||
|
|
@ -22,7 +23,9 @@ Example:
|
|||
key@40050000 {
|
||||
compatible = "nxp,lpc3220-key";
|
||||
reg = <0x40050000 0x1000>;
|
||||
interrupts = <54 0>;
|
||||
clocks = <&clk LPC32XX_CLK_KEY>;
|
||||
interrupt-parent = <&sic1>;
|
||||
interrupts = <22 IRQ_TYPE_LEVEL_HIGH>;
|
||||
keypad,num-rows = <1>;
|
||||
keypad,num-columns = <1>;
|
||||
nxp,debounce-delay-ms = <3>;
|
||||
|
|
|
|||
|
|
@ -0,0 +1,78 @@
|
|||
Microchip AT42QT1050 Five-channel Touch Sensor IC
|
||||
|
||||
The AT42QT1050 (QT1050) is a QTouchADC sensor device. The device can sense from
|
||||
one to five keys, dependent on mode. The QT1050 includes all signal processing
|
||||
functions necessary to provide stable sensing under a wide variety of changing
|
||||
conditions, and the outputs are fully debounced.
|
||||
|
||||
The touchkey device node should be placed inside an I2C bus node.
|
||||
|
||||
Required properties:
|
||||
- compatible: Must be "microchip,qt1050"
|
||||
- reg: The I2C address of the device
|
||||
- interrupts: The sink for the touchpad's IRQ output,
|
||||
see ../interrupt-controller/interrupts.txt
|
||||
|
||||
Optional properties:
|
||||
- wakeup-source: touch keys can be used as a wakeup source
|
||||
|
||||
Each button (key) is represented as a sub-node:
|
||||
|
||||
Each not specified key or key with linux,code set to KEY_RESERVED gets disabled
|
||||
in HW.
|
||||
|
||||
Subnode properties:
|
||||
- linux,code: Keycode to emit.
|
||||
- reg: The key number. Valid values: 0, 1, 2, 3, 4.
|
||||
|
||||
Optional subnode-properties:
|
||||
|
||||
If a optional property is missing or has a invalid value the default value is
|
||||
taken.
|
||||
|
||||
- microchip,pre-charge-time-ns:
|
||||
Each touchpad need some time to precharge. The value depends on the mechanical
|
||||
layout.
|
||||
Valid value range: 0 - 637500; values must be a multiple of 2500;
|
||||
default is 0.
|
||||
- microchip,average-samples:
|
||||
Number of data samples which are averaged for each read.
|
||||
Valid values: 1, 4, 16, 64, 256, 1024, 4096, 16384; default is 1.
|
||||
- microchip,average-scaling:
|
||||
The scaling factor which is used to scale the average-samples.
|
||||
Valid values: 1, 2, 4, 8, 16, 32, 64, 128; default is 1.
|
||||
- microchip,threshold:
|
||||
Number of counts to register a touch detection.
|
||||
Valid value range: 0 - 255; default is 20.
|
||||
|
||||
Example:
|
||||
QT1050 with 3 non continuous keys, key2 and key4 are disabled.
|
||||
|
||||
touchkeys@41 {
|
||||
compatible = "microchip,qt1050";
|
||||
reg = <0x41>;
|
||||
interrupt-parent = <&gpio0>;
|
||||
interrupts = <17 IRQ_TYPE_EDGE_FALLING>;
|
||||
|
||||
up@0 {
|
||||
reg = <0>;
|
||||
linux,code = <KEY_UP>;
|
||||
microchip,average-samples = <64>;
|
||||
microchip,average-scaling = <16>;
|
||||
microchip,pre-charge-time-ns = <10000>;
|
||||
};
|
||||
|
||||
right@1 {
|
||||
reg = <1>;
|
||||
linux,code = <KEY_RIGHT>;
|
||||
microchip,average-samples = <64>;
|
||||
microchip,average-scaling = <8>;
|
||||
};
|
||||
|
||||
down@3 {
|
||||
reg = <3>;
|
||||
linux,code = <KEY_DOWN>;
|
||||
microchip,average-samples = <256>;
|
||||
microchip,average-scaling = <16>;
|
||||
};
|
||||
};
|
||||
|
|
@ -2,12 +2,14 @@ Allwinner sun4i low res adc attached tablet keys
|
|||
------------------------------------------------
|
||||
|
||||
Required properties:
|
||||
- compatible: "allwinner,sun4i-a10-lradc-keys"
|
||||
- compatible: should be one of the following string:
|
||||
"allwinner,sun4i-a10-lradc-keys"
|
||||
"allwinner,sun8i-a83t-r-lradc"
|
||||
- reg: mmio address range of the chip
|
||||
- interrupts: interrupt to which the chip is connected
|
||||
- vref-supply: powersupply for the lradc reference voltage
|
||||
|
||||
Each key is represented as a sub-node of "allwinner,sun4i-a10-lradc-keys":
|
||||
Each key is represented as a sub-node of the compatible mentioned above:
|
||||
|
||||
Required subnode-properties:
|
||||
- label: Descriptive name of the key.
|
||||
|
|
|
|||
|
|
@ -3,6 +3,7 @@ Device tree bindings for Goodix GT9xx series touchscreen controller
|
|||
Required properties:
|
||||
|
||||
- compatible : Should be "goodix,gt1151"
|
||||
or "goodix,gt5663"
|
||||
or "goodix,gt5688"
|
||||
or "goodix,gt911"
|
||||
or "goodix,gt9110"
|
||||
|
|
@ -19,6 +20,8 @@ Optional properties:
|
|||
- irq-gpios : GPIO pin used for IRQ. The driver uses the
|
||||
interrupt gpio pin as output to reset the device.
|
||||
- reset-gpios : GPIO pin used for reset
|
||||
- AVDD28-supply : Analog power supply regulator on AVDD28 pin
|
||||
- VDDIO-supply : GPIO power supply regulator on VDDIO pin
|
||||
- touchscreen-inverted-x
|
||||
- touchscreen-inverted-y
|
||||
- touchscreen-size-x
|
||||
|
|
|
|||
|
|
@ -0,0 +1,80 @@
|
|||
Azoteq IQS550/572/525 Trackpad/Touchscreen Controller
|
||||
|
||||
Required properties:
|
||||
|
||||
- compatible : Must be equal to one of the following:
|
||||
"azoteq,iqs550"
|
||||
"azoteq,iqs572"
|
||||
"azoteq,iqs525"
|
||||
|
||||
- reg : I2C slave address for the device.
|
||||
|
||||
- interrupts : GPIO to which the device's active-high RDY
|
||||
output is connected (see [0]).
|
||||
|
||||
- reset-gpios : GPIO to which the device's active-low NRST
|
||||
input is connected (see [1]).
|
||||
|
||||
Optional properties:
|
||||
|
||||
- touchscreen-min-x : See [2].
|
||||
|
||||
- touchscreen-min-y : See [2].
|
||||
|
||||
- touchscreen-size-x : See [2]. If this property is omitted, the
|
||||
maximum x-coordinate is specified by the
|
||||
device's "X Resolution" register.
|
||||
|
||||
- touchscreen-size-y : See [2]. If this property is omitted, the
|
||||
maximum y-coordinate is specified by the
|
||||
device's "Y Resolution" register.
|
||||
|
||||
- touchscreen-max-pressure : See [2]. Pressure is expressed as the sum of
|
||||
the deltas across all channels impacted by a
|
||||
touch event. A channel's delta is calculated
|
||||
as its count value minus a reference, where
|
||||
the count value is inversely proportional to
|
||||
the channel's capacitance.
|
||||
|
||||
- touchscreen-fuzz-x : See [2].
|
||||
|
||||
- touchscreen-fuzz-y : See [2].
|
||||
|
||||
- touchscreen-fuzz-pressure : See [2].
|
||||
|
||||
- touchscreen-inverted-x : See [2]. Inversion is applied relative to that
|
||||
which may already be specified by the device's
|
||||
FLIP_X and FLIP_Y register fields.
|
||||
|
||||
- touchscreen-inverted-y : See [2]. Inversion is applied relative to that
|
||||
which may already be specified by the device's
|
||||
FLIP_X and FLIP_Y register fields.
|
||||
|
||||
- touchscreen-swapped-x-y : See [2]. Swapping is applied relative to that
|
||||
which may already be specified by the device's
|
||||
SWITCH_XY_AXIS register field.
|
||||
|
||||
[0]: Documentation/devicetree/bindings/interrupt-controller/interrupts.txt
|
||||
[1]: Documentation/devicetree/bindings/gpio/gpio.txt
|
||||
[2]: Documentation/devicetree/bindings/input/touchscreen/touchscreen.txt
|
||||
|
||||
Example:
|
||||
|
||||
&i2c1 {
|
||||
/* ... */
|
||||
|
||||
touchscreen@74 {
|
||||
compatible = "azoteq,iqs550";
|
||||
reg = <0x74>;
|
||||
interrupt-parent = <&gpio>;
|
||||
interrupts = <17 4>;
|
||||
reset-gpios = <&gpio 27 1>;
|
||||
|
||||
touchscreen-size-x = <640>;
|
||||
touchscreen-size-y = <480>;
|
||||
|
||||
touchscreen-max-pressure = <16000>;
|
||||
};
|
||||
|
||||
/* ... */
|
||||
};
|
||||
|
|
@ -53,6 +53,7 @@ avic Shanghai AVIC Optoelectronics Co., Ltd.
|
|||
avnet Avnet, Inc.
|
||||
axentia Axentia Technologies AB
|
||||
axis Axis Communications AB
|
||||
azoteq Azoteq (Pty) Ltd
|
||||
bananapi BIPAI KEJI LIMITED
|
||||
bhf Beckhoff Automation GmbH & Co. KG
|
||||
bitmain Bitmain Technologies
|
||||
|
|
|
|||
|
|
@ -1036,6 +1036,8 @@ static void hidinput_configure_usage(struct hid_input *hidinput, struct hid_fiel
|
|||
case 0x28b: map_key_clear(KEY_FORWARDMAIL); break;
|
||||
case 0x28c: map_key_clear(KEY_SEND); break;
|
||||
|
||||
case 0x29d: map_key_clear(KEY_KBD_LAYOUT_NEXT); break;
|
||||
|
||||
case 0x2c7: map_key_clear(KEY_KBDINPUTASSIST_PREV); break;
|
||||
case 0x2c8: map_key_clear(KEY_KBDINPUTASSIST_NEXT); break;
|
||||
case 0x2c9: map_key_clear(KEY_KBDINPUTASSIST_PREVGROUP); break;
|
||||
|
|
|
|||
|
|
@ -503,14 +503,13 @@ static int evdev_open(struct inode *inode, struct file *file)
|
|||
{
|
||||
struct evdev *evdev = container_of(inode->i_cdev, struct evdev, cdev);
|
||||
unsigned int bufsize = evdev_compute_buffer_size(evdev->handle.dev);
|
||||
unsigned int size = sizeof(struct evdev_client) +
|
||||
bufsize * sizeof(struct input_event);
|
||||
struct evdev_client *client;
|
||||
int error;
|
||||
|
||||
client = kzalloc(size, GFP_KERNEL | __GFP_NOWARN);
|
||||
client = kzalloc(struct_size(client, buffer, bufsize),
|
||||
GFP_KERNEL | __GFP_NOWARN);
|
||||
if (!client)
|
||||
client = vzalloc(size);
|
||||
client = vzalloc(struct_size(client, buffer, bufsize));
|
||||
if (!client)
|
||||
return -ENOMEM;
|
||||
|
||||
|
|
|
|||
|
|
@ -137,6 +137,17 @@ config KEYBOARD_ATKBD_RDI_KEYCODES
|
|||
right-hand column will be interpreted as the key shown in the
|
||||
left-hand column.
|
||||
|
||||
config KEYBOARD_QT1050
|
||||
tristate "Microchip AT42QT1050 Touch Sensor Chip"
|
||||
depends on I2C
|
||||
select REGMAP_I2C
|
||||
help
|
||||
Say Y here if you want to use Microchip AT42QT1050 QTouch
|
||||
Sensor chip as input device.
|
||||
|
||||
To compile this driver as a module, choose M here:
|
||||
the module will be called qt1050
|
||||
|
||||
config KEYBOARD_QT1070
|
||||
tristate "Atmel AT42QT1070 Touch Sensor Chip"
|
||||
depends on I2C
|
||||
|
|
|
|||
|
|
@ -50,6 +50,7 @@ obj-$(CONFIG_KEYBOARD_OPENCORES) += opencores-kbd.o
|
|||
obj-$(CONFIG_KEYBOARD_PMIC8XXX) += pmic8xxx-keypad.o
|
||||
obj-$(CONFIG_KEYBOARD_PXA27x) += pxa27x_keypad.o
|
||||
obj-$(CONFIG_KEYBOARD_PXA930_ROTARY) += pxa930_rotary.o
|
||||
obj-$(CONFIG_KEYBOARD_QT1050) += qt1050.o
|
||||
obj-$(CONFIG_KEYBOARD_QT1070) += qt1070.o
|
||||
obj-$(CONFIG_KEYBOARD_QT2160) += qt2160.o
|
||||
obj-$(CONFIG_KEYBOARD_SAMSUNG) += samsung-keypad.o
|
||||
|
|
|
|||
|
|
@ -401,6 +401,8 @@ static irqreturn_t atkbd_interrupt(struct serio *serio, unsigned char data,
|
|||
if (ps2_handle_response(&atkbd->ps2dev, data))
|
||||
goto out;
|
||||
|
||||
pm_wakeup_event(&serio->dev, 0);
|
||||
|
||||
if (!atkbd->enabled)
|
||||
goto out;
|
||||
|
||||
|
|
|
|||
|
|
@ -0,0 +1,598 @@
|
|||
// SPDX-License-Identifier: GPL-2.0
|
||||
/*
|
||||
* Microchip AT42QT1050 QTouch Sensor Controller
|
||||
*
|
||||
* Copyright (C) 2019 Pengutronix, Marco Felsch <kernel@pengutronix.de>
|
||||
*
|
||||
* Base on AT42QT1070 driver by:
|
||||
* Bo Shen <voice.shen@atmel.com>
|
||||
* Copyright (C) 2011 Atmel
|
||||
*/
|
||||
|
||||
#include <linux/delay.h>
|
||||
#include <linux/i2c.h>
|
||||
#include <linux/input.h>
|
||||
#include <linux/interrupt.h>
|
||||
#include <linux/kernel.h>
|
||||
#include <linux/log2.h>
|
||||
#include <linux/module.h>
|
||||
#include <linux/of.h>
|
||||
#include <linux/regmap.h>
|
||||
|
||||
/* Chip ID */
|
||||
#define QT1050_CHIP_ID 0x00
|
||||
#define QT1050_CHIP_ID_VER 0x46
|
||||
|
||||
/* Firmware version */
|
||||
#define QT1050_FW_VERSION 0x01
|
||||
|
||||
/* Detection status */
|
||||
#define QT1050_DET_STATUS 0x02
|
||||
|
||||
/* Key status */
|
||||
#define QT1050_KEY_STATUS 0x03
|
||||
|
||||
/* Key Signals */
|
||||
#define QT1050_KEY_SIGNAL_0_MSB 0x06
|
||||
#define QT1050_KEY_SIGNAL_0_LSB 0x07
|
||||
#define QT1050_KEY_SIGNAL_1_MSB 0x08
|
||||
#define QT1050_KEY_SIGNAL_1_LSB 0x09
|
||||
#define QT1050_KEY_SIGNAL_2_MSB 0x0c
|
||||
#define QT1050_KEY_SIGNAL_2_LSB 0x0d
|
||||
#define QT1050_KEY_SIGNAL_3_MSB 0x0e
|
||||
#define QT1050_KEY_SIGNAL_3_LSB 0x0f
|
||||
#define QT1050_KEY_SIGNAL_4_MSB 0x10
|
||||
#define QT1050_KEY_SIGNAL_4_LSB 0x11
|
||||
|
||||
/* Reference data */
|
||||
#define QT1050_REF_DATA_0_MSB 0x14
|
||||
#define QT1050_REF_DATA_0_LSB 0x15
|
||||
#define QT1050_REF_DATA_1_MSB 0x16
|
||||
#define QT1050_REF_DATA_1_LSB 0x17
|
||||
#define QT1050_REF_DATA_2_MSB 0x1a
|
||||
#define QT1050_REF_DATA_2_LSB 0x1b
|
||||
#define QT1050_REF_DATA_3_MSB 0x1c
|
||||
#define QT1050_REF_DATA_3_LSB 0x1d
|
||||
#define QT1050_REF_DATA_4_MSB 0x1e
|
||||
#define QT1050_REF_DATA_4_LSB 0x1f
|
||||
|
||||
/* Negative threshold level */
|
||||
#define QT1050_NTHR_0 0x21
|
||||
#define QT1050_NTHR_1 0x22
|
||||
#define QT1050_NTHR_2 0x24
|
||||
#define QT1050_NTHR_3 0x25
|
||||
#define QT1050_NTHR_4 0x26
|
||||
|
||||
/* Pulse / Scale */
|
||||
#define QT1050_PULSE_SCALE_0 0x28
|
||||
#define QT1050_PULSE_SCALE_1 0x29
|
||||
#define QT1050_PULSE_SCALE_2 0x2b
|
||||
#define QT1050_PULSE_SCALE_3 0x2c
|
||||
#define QT1050_PULSE_SCALE_4 0x2d
|
||||
|
||||
/* Detection integrator counter / AKS */
|
||||
#define QT1050_DI_AKS_0 0x2f
|
||||
#define QT1050_DI_AKS_1 0x30
|
||||
#define QT1050_DI_AKS_2 0x32
|
||||
#define QT1050_DI_AKS_3 0x33
|
||||
#define QT1050_DI_AKS_4 0x34
|
||||
|
||||
/* Charge Share Delay */
|
||||
#define QT1050_CSD_0 0x36
|
||||
#define QT1050_CSD_1 0x37
|
||||
#define QT1050_CSD_2 0x39
|
||||
#define QT1050_CSD_3 0x3a
|
||||
#define QT1050_CSD_4 0x3b
|
||||
|
||||
/* Low Power Mode */
|
||||
#define QT1050_LPMODE 0x3d
|
||||
|
||||
/* Calibration and Reset */
|
||||
#define QT1050_RES_CAL 0x3f
|
||||
#define QT1050_RES_CAL_RESET BIT(7)
|
||||
#define QT1050_RES_CAL_CALIBRATE BIT(1)
|
||||
|
||||
#define QT1050_MAX_KEYS 5
|
||||
#define QT1050_RESET_TIME 255
|
||||
|
||||
struct qt1050_key_regs {
|
||||
unsigned int nthr;
|
||||
unsigned int pulse_scale;
|
||||
unsigned int di_aks;
|
||||
unsigned int csd;
|
||||
};
|
||||
|
||||
struct qt1050_key {
|
||||
u32 num;
|
||||
u32 charge_delay;
|
||||
u32 thr_cnt;
|
||||
u32 samples;
|
||||
u32 scale;
|
||||
u32 keycode;
|
||||
};
|
||||
|
||||
struct qt1050_priv {
|
||||
struct i2c_client *client;
|
||||
struct input_dev *input;
|
||||
struct regmap *regmap;
|
||||
struct qt1050_key keys[QT1050_MAX_KEYS];
|
||||
unsigned short keycodes[QT1050_MAX_KEYS];
|
||||
u8 reg_keys;
|
||||
u8 last_keys;
|
||||
};
|
||||
|
||||
static const struct qt1050_key_regs qt1050_key_regs_data[] = {
|
||||
{
|
||||
.nthr = QT1050_NTHR_0,
|
||||
.pulse_scale = QT1050_PULSE_SCALE_0,
|
||||
.di_aks = QT1050_DI_AKS_0,
|
||||
.csd = QT1050_CSD_0,
|
||||
}, {
|
||||
.nthr = QT1050_NTHR_1,
|
||||
.pulse_scale = QT1050_PULSE_SCALE_1,
|
||||
.di_aks = QT1050_DI_AKS_1,
|
||||
.csd = QT1050_CSD_1,
|
||||
}, {
|
||||
.nthr = QT1050_NTHR_2,
|
||||
.pulse_scale = QT1050_PULSE_SCALE_2,
|
||||
.di_aks = QT1050_DI_AKS_2,
|
||||
.csd = QT1050_CSD_2,
|
||||
}, {
|
||||
.nthr = QT1050_NTHR_3,
|
||||
.pulse_scale = QT1050_PULSE_SCALE_3,
|
||||
.di_aks = QT1050_DI_AKS_3,
|
||||
.csd = QT1050_CSD_3,
|
||||
}, {
|
||||
.nthr = QT1050_NTHR_4,
|
||||
.pulse_scale = QT1050_PULSE_SCALE_4,
|
||||
.di_aks = QT1050_DI_AKS_4,
|
||||
.csd = QT1050_CSD_4,
|
||||
}
|
||||
};
|
||||
|
||||
static bool qt1050_volatile_reg(struct device *dev, unsigned int reg)
|
||||
{
|
||||
switch (reg) {
|
||||
case QT1050_DET_STATUS:
|
||||
case QT1050_KEY_STATUS:
|
||||
case QT1050_KEY_SIGNAL_0_MSB:
|
||||
case QT1050_KEY_SIGNAL_0_LSB:
|
||||
case QT1050_KEY_SIGNAL_1_MSB:
|
||||
case QT1050_KEY_SIGNAL_1_LSB:
|
||||
case QT1050_KEY_SIGNAL_2_MSB:
|
||||
case QT1050_KEY_SIGNAL_2_LSB:
|
||||
case QT1050_KEY_SIGNAL_3_MSB:
|
||||
case QT1050_KEY_SIGNAL_3_LSB:
|
||||
case QT1050_KEY_SIGNAL_4_MSB:
|
||||
case QT1050_KEY_SIGNAL_4_LSB:
|
||||
return true;
|
||||
default:
|
||||
return false;
|
||||
}
|
||||
}
|
||||
|
||||
static const struct regmap_range qt1050_readable_ranges[] = {
|
||||
regmap_reg_range(QT1050_CHIP_ID, QT1050_KEY_STATUS),
|
||||
regmap_reg_range(QT1050_KEY_SIGNAL_0_MSB, QT1050_KEY_SIGNAL_1_LSB),
|
||||
regmap_reg_range(QT1050_KEY_SIGNAL_2_MSB, QT1050_KEY_SIGNAL_4_LSB),
|
||||
regmap_reg_range(QT1050_REF_DATA_0_MSB, QT1050_REF_DATA_1_LSB),
|
||||
regmap_reg_range(QT1050_REF_DATA_2_MSB, QT1050_REF_DATA_4_LSB),
|
||||
regmap_reg_range(QT1050_NTHR_0, QT1050_NTHR_1),
|
||||
regmap_reg_range(QT1050_NTHR_2, QT1050_NTHR_4),
|
||||
regmap_reg_range(QT1050_PULSE_SCALE_0, QT1050_PULSE_SCALE_1),
|
||||
regmap_reg_range(QT1050_PULSE_SCALE_2, QT1050_PULSE_SCALE_4),
|
||||
regmap_reg_range(QT1050_DI_AKS_0, QT1050_DI_AKS_1),
|
||||
regmap_reg_range(QT1050_DI_AKS_2, QT1050_DI_AKS_4),
|
||||
regmap_reg_range(QT1050_CSD_0, QT1050_CSD_1),
|
||||
regmap_reg_range(QT1050_CSD_2, QT1050_RES_CAL),
|
||||
};
|
||||
|
||||
static const struct regmap_access_table qt1050_readable_table = {
|
||||
.yes_ranges = qt1050_readable_ranges,
|
||||
.n_yes_ranges = ARRAY_SIZE(qt1050_readable_ranges),
|
||||
};
|
||||
|
||||
static const struct regmap_range qt1050_writeable_ranges[] = {
|
||||
regmap_reg_range(QT1050_NTHR_0, QT1050_NTHR_1),
|
||||
regmap_reg_range(QT1050_NTHR_2, QT1050_NTHR_4),
|
||||
regmap_reg_range(QT1050_PULSE_SCALE_0, QT1050_PULSE_SCALE_1),
|
||||
regmap_reg_range(QT1050_PULSE_SCALE_2, QT1050_PULSE_SCALE_4),
|
||||
regmap_reg_range(QT1050_DI_AKS_0, QT1050_DI_AKS_1),
|
||||
regmap_reg_range(QT1050_DI_AKS_2, QT1050_DI_AKS_4),
|
||||
regmap_reg_range(QT1050_CSD_0, QT1050_CSD_1),
|
||||
regmap_reg_range(QT1050_CSD_2, QT1050_RES_CAL),
|
||||
};
|
||||
|
||||
static const struct regmap_access_table qt1050_writeable_table = {
|
||||
.yes_ranges = qt1050_writeable_ranges,
|
||||
.n_yes_ranges = ARRAY_SIZE(qt1050_writeable_ranges),
|
||||
};
|
||||
|
||||
static struct regmap_config qt1050_regmap_config = {
|
||||
.reg_bits = 8,
|
||||
.val_bits = 8,
|
||||
.max_register = QT1050_RES_CAL,
|
||||
|
||||
.cache_type = REGCACHE_RBTREE,
|
||||
|
||||
.wr_table = &qt1050_writeable_table,
|
||||
.rd_table = &qt1050_readable_table,
|
||||
.volatile_reg = qt1050_volatile_reg,
|
||||
};
|
||||
|
||||
static bool qt1050_identify(struct qt1050_priv *ts)
|
||||
{
|
||||
unsigned int val;
|
||||
int err;
|
||||
|
||||
/* Read Chip ID */
|
||||
regmap_read(ts->regmap, QT1050_CHIP_ID, &val);
|
||||
if (val != QT1050_CHIP_ID_VER) {
|
||||
dev_err(&ts->client->dev, "ID %d not supported\n", val);
|
||||
return false;
|
||||
}
|
||||
|
||||
/* Read firmware version */
|
||||
err = regmap_read(ts->regmap, QT1050_FW_VERSION, &val);
|
||||
if (err) {
|
||||
dev_err(&ts->client->dev, "could not read the firmware version\n");
|
||||
return false;
|
||||
}
|
||||
|
||||
dev_info(&ts->client->dev, "AT42QT1050 firmware version %1d.%1d\n",
|
||||
val >> 4, val & 0xf);
|
||||
|
||||
return true;
|
||||
}
|
||||
|
||||
static irqreturn_t qt1050_irq_threaded(int irq, void *dev_id)
|
||||
{
|
||||
struct qt1050_priv *ts = dev_id;
|
||||
struct input_dev *input = ts->input;
|
||||
unsigned long new_keys, changed;
|
||||
unsigned int val;
|
||||
int i, err;
|
||||
|
||||
/* Read the detected status register, thus clearing interrupt */
|
||||
err = regmap_read(ts->regmap, QT1050_DET_STATUS, &val);
|
||||
if (err) {
|
||||
dev_err(&ts->client->dev, "Fail to read detection status: %d\n",
|
||||
err);
|
||||
return IRQ_NONE;
|
||||
}
|
||||
|
||||
/* Read which key changed, keys are not continuous */
|
||||
err = regmap_read(ts->regmap, QT1050_KEY_STATUS, &val);
|
||||
if (err) {
|
||||
dev_err(&ts->client->dev,
|
||||
"Fail to determine the key status: %d\n", err);
|
||||
return IRQ_NONE;
|
||||
}
|
||||
new_keys = (val & 0x70) >> 2 | (val & 0x6) >> 1;
|
||||
changed = ts->last_keys ^ new_keys;
|
||||
/* Report registered keys only */
|
||||
changed &= ts->reg_keys;
|
||||
|
||||
for_each_set_bit(i, &changed, QT1050_MAX_KEYS)
|
||||
input_report_key(input, ts->keys[i].keycode,
|
||||
test_bit(i, &new_keys));
|
||||
|
||||
ts->last_keys = new_keys;
|
||||
input_sync(input);
|
||||
|
||||
return IRQ_HANDLED;
|
||||
}
|
||||
|
||||
static const struct qt1050_key_regs *qt1050_get_key_regs(int key_num)
|
||||
{
|
||||
return &qt1050_key_regs_data[key_num];
|
||||
}
|
||||
|
||||
static int qt1050_set_key(struct regmap *map, int number, int on)
|
||||
{
|
||||
const struct qt1050_key_regs *key_regs;
|
||||
|
||||
key_regs = qt1050_get_key_regs(number);
|
||||
|
||||
return regmap_update_bits(map, key_regs->di_aks, 0xfc,
|
||||
on ? BIT(4) : 0x00);
|
||||
}
|
||||
|
||||
static int qt1050_apply_fw_data(struct qt1050_priv *ts)
|
||||
{
|
||||
struct regmap *map = ts->regmap;
|
||||
struct qt1050_key *button = &ts->keys[0];
|
||||
const struct qt1050_key_regs *key_regs;
|
||||
int i, err;
|
||||
|
||||
/* Disable all keys and enable only the specified ones */
|
||||
for (i = 0; i < QT1050_MAX_KEYS; i++) {
|
||||
err = qt1050_set_key(map, i, 0);
|
||||
if (err)
|
||||
return err;
|
||||
}
|
||||
|
||||
for (i = 0; i < QT1050_MAX_KEYS; i++, button++) {
|
||||
/* Keep KEY_RESERVED keys off */
|
||||
if (button->keycode == KEY_RESERVED)
|
||||
continue;
|
||||
|
||||
err = qt1050_set_key(map, button->num, 1);
|
||||
if (err)
|
||||
return err;
|
||||
|
||||
key_regs = qt1050_get_key_regs(button->num);
|
||||
|
||||
err = regmap_write(map, key_regs->pulse_scale,
|
||||
(button->samples << 4) | (button->scale));
|
||||
if (err)
|
||||
return err;
|
||||
err = regmap_write(map, key_regs->csd, button->charge_delay);
|
||||
if (err)
|
||||
return err;
|
||||
err = regmap_write(map, key_regs->nthr, button->thr_cnt);
|
||||
if (err)
|
||||
return err;
|
||||
}
|
||||
|
||||
return 0;
|
||||
}
|
||||
|
||||
static int qt1050_parse_fw(struct qt1050_priv *ts)
|
||||
{
|
||||
struct device *dev = &ts->client->dev;
|
||||
struct fwnode_handle *child;
|
||||
int nbuttons;
|
||||
|
||||
nbuttons = device_get_child_node_count(dev);
|
||||
if (nbuttons == 0 || nbuttons > QT1050_MAX_KEYS)
|
||||
return -ENODEV;
|
||||
|
||||
device_for_each_child_node(dev, child) {
|
||||
struct qt1050_key button;
|
||||
|
||||
/* Required properties */
|
||||
if (fwnode_property_read_u32(child, "linux,code",
|
||||
&button.keycode)) {
|
||||
dev_err(dev, "Button without keycode\n");
|
||||
goto err;
|
||||
}
|
||||
if (button.keycode >= KEY_MAX) {
|
||||
dev_err(dev, "Invalid keycode 0x%x\n",
|
||||
button.keycode);
|
||||
goto err;
|
||||
}
|
||||
|
||||
if (fwnode_property_read_u32(child, "reg",
|
||||
&button.num)) {
|
||||
dev_err(dev, "Button without pad number\n");
|
||||
goto err;
|
||||
}
|
||||
if (button.num < 0 || button.num > QT1050_MAX_KEYS - 1)
|
||||
goto err;
|
||||
|
||||
ts->reg_keys |= BIT(button.num);
|
||||
|
||||
/* Optional properties */
|
||||
if (fwnode_property_read_u32(child,
|
||||
"microchip,pre-charge-time-ns",
|
||||
&button.charge_delay)) {
|
||||
button.charge_delay = 0;
|
||||
} else {
|
||||
if (button.charge_delay % 2500 == 0)
|
||||
button.charge_delay =
|
||||
button.charge_delay / 2500;
|
||||
else
|
||||
button.charge_delay = 0;
|
||||
}
|
||||
|
||||
if (fwnode_property_read_u32(child, "microchip,average-samples",
|
||||
&button.samples)) {
|
||||
button.samples = 0;
|
||||
} else {
|
||||
if (is_power_of_2(button.samples))
|
||||
button.samples = ilog2(button.samples);
|
||||
else
|
||||
button.samples = 0;
|
||||
}
|
||||
|
||||
if (fwnode_property_read_u32(child, "microchip,average-scaling",
|
||||
&button.scale)) {
|
||||
button.scale = 0;
|
||||
} else {
|
||||
if (is_power_of_2(button.scale))
|
||||
button.scale = ilog2(button.scale);
|
||||
else
|
||||
button.scale = 0;
|
||||
|
||||
}
|
||||
|
||||
if (fwnode_property_read_u32(child, "microchip,threshold",
|
||||
&button.thr_cnt)) {
|
||||
button.thr_cnt = 20;
|
||||
} else {
|
||||
if (button.thr_cnt > 255)
|
||||
button.thr_cnt = 20;
|
||||
}
|
||||
|
||||
ts->keys[button.num] = button;
|
||||
}
|
||||
|
||||
return 0;
|
||||
|
||||
err:
|
||||
fwnode_handle_put(child);
|
||||
return -EINVAL;
|
||||
}
|
||||
|
||||
static int qt1050_probe(struct i2c_client *client)
|
||||
{
|
||||
struct qt1050_priv *ts;
|
||||
struct input_dev *input;
|
||||
struct device *dev = &client->dev;
|
||||
struct regmap *map;
|
||||
unsigned int status, i;
|
||||
int err;
|
||||
|
||||
/* Check basic functionality */
|
||||
err = i2c_check_functionality(client->adapter, I2C_FUNC_SMBUS_BYTE);
|
||||
if (!err) {
|
||||
dev_err(&client->dev, "%s adapter not supported\n",
|
||||
dev_driver_string(&client->adapter->dev));
|
||||
return -ENODEV;
|
||||
}
|
||||
|
||||
if (!client->irq) {
|
||||
dev_err(dev, "assign a irq line to this device\n");
|
||||
return -EINVAL;
|
||||
}
|
||||
|
||||
ts = devm_kzalloc(dev, sizeof(*ts), GFP_KERNEL);
|
||||
if (!ts)
|
||||
return -ENOMEM;
|
||||
|
||||
input = devm_input_allocate_device(dev);
|
||||
if (!input)
|
||||
return -ENOMEM;
|
||||
|
||||
map = devm_regmap_init_i2c(client, &qt1050_regmap_config);
|
||||
if (IS_ERR(map))
|
||||
return PTR_ERR(map);
|
||||
|
||||
ts->client = client;
|
||||
ts->input = input;
|
||||
ts->regmap = map;
|
||||
|
||||
i2c_set_clientdata(client, ts);
|
||||
|
||||
/* Identify the qt1050 chip */
|
||||
if (!qt1050_identify(ts))
|
||||
return -ENODEV;
|
||||
|
||||
/* Get pdata */
|
||||
err = qt1050_parse_fw(ts);
|
||||
if (err) {
|
||||
dev_err(dev, "Failed to parse firmware: %d\n", err);
|
||||
return err;
|
||||
}
|
||||
|
||||
input->name = "AT42QT1050 QTouch Sensor";
|
||||
input->dev.parent = &client->dev;
|
||||
input->id.bustype = BUS_I2C;
|
||||
|
||||
/* Add the keycode */
|
||||
input->keycode = ts->keycodes;
|
||||
input->keycodesize = sizeof(ts->keycodes[0]);
|
||||
input->keycodemax = QT1050_MAX_KEYS;
|
||||
|
||||
__set_bit(EV_KEY, input->evbit);
|
||||
for (i = 0; i < QT1050_MAX_KEYS; i++) {
|
||||
ts->keycodes[i] = ts->keys[i].keycode;
|
||||
__set_bit(ts->keycodes[i], input->keybit);
|
||||
}
|
||||
|
||||
/* Trigger re-calibration */
|
||||
err = regmap_update_bits(ts->regmap, QT1050_RES_CAL, 0x7f,
|
||||
QT1050_RES_CAL_CALIBRATE);
|
||||
if (err) {
|
||||
dev_err(dev, "Trigger calibration failed: %d\n", err);
|
||||
return err;
|
||||
}
|
||||
err = regmap_read_poll_timeout(ts->regmap, QT1050_DET_STATUS, status,
|
||||
status >> 7 == 1, 10000, 200000);
|
||||
if (err) {
|
||||
dev_err(dev, "Calibration failed: %d\n", err);
|
||||
return err;
|
||||
}
|
||||
|
||||
/* Soft reset to set defaults */
|
||||
err = regmap_update_bits(ts->regmap, QT1050_RES_CAL,
|
||||
QT1050_RES_CAL_RESET, QT1050_RES_CAL_RESET);
|
||||
if (err) {
|
||||
dev_err(dev, "Trigger soft reset failed: %d\n", err);
|
||||
return err;
|
||||
}
|
||||
msleep(QT1050_RESET_TIME);
|
||||
|
||||
/* Set pdata */
|
||||
err = qt1050_apply_fw_data(ts);
|
||||
if (err) {
|
||||
dev_err(dev, "Failed to set firmware data: %d\n", err);
|
||||
return err;
|
||||
}
|
||||
|
||||
err = devm_request_threaded_irq(dev, client->irq, NULL,
|
||||
qt1050_irq_threaded, IRQF_ONESHOT,
|
||||
"qt1050", ts);
|
||||
if (err) {
|
||||
dev_err(&client->dev, "Failed to request irq: %d\n", err);
|
||||
return err;
|
||||
}
|
||||
|
||||
/* Clear #CHANGE line */
|
||||
err = regmap_read(ts->regmap, QT1050_DET_STATUS, &status);
|
||||
if (err) {
|
||||
dev_err(dev, "Failed to clear #CHANGE line level: %d\n", err);
|
||||
return err;
|
||||
}
|
||||
|
||||
/* Register the input device */
|
||||
err = input_register_device(ts->input);
|
||||
if (err) {
|
||||
dev_err(&client->dev, "Failed to register input device: %d\n",
|
||||
err);
|
||||
return err;
|
||||
}
|
||||
|
||||
return 0;
|
||||
}
|
||||
|
||||
static int __maybe_unused qt1050_suspend(struct device *dev)
|
||||
{
|
||||
struct i2c_client *client = to_i2c_client(dev);
|
||||
struct qt1050_priv *ts = i2c_get_clientdata(client);
|
||||
|
||||
disable_irq(client->irq);
|
||||
|
||||
/*
|
||||
* Set measurement interval to 1s (125 x 8ms) if wakeup is allowed
|
||||
* else turn off. The 1s interval seems to be a good compromise between
|
||||
* low power and response time.
|
||||
*/
|
||||
return regmap_write(ts->regmap, QT1050_LPMODE,
|
||||
device_may_wakeup(dev) ? 125 : 0);
|
||||
}
|
||||
|
||||
static int __maybe_unused qt1050_resume(struct device *dev)
|
||||
{
|
||||
struct i2c_client *client = to_i2c_client(dev);
|
||||
struct qt1050_priv *ts = i2c_get_clientdata(client);
|
||||
|
||||
enable_irq(client->irq);
|
||||
|
||||
/* Set measurement interval back to 16ms (2 x 8ms) */
|
||||
return regmap_write(ts->regmap, QT1050_LPMODE, 2);
|
||||
}
|
||||
|
||||
static SIMPLE_DEV_PM_OPS(qt1050_pm_ops, qt1050_suspend, qt1050_resume);
|
||||
|
||||
static const struct of_device_id __maybe_unused qt1050_of_match[] = {
|
||||
{ .compatible = "microchip,qt1050", },
|
||||
{ },
|
||||
};
|
||||
MODULE_DEVICE_TABLE(of, qt1050_of_match);
|
||||
|
||||
static struct i2c_driver qt1050_driver = {
|
||||
.driver = {
|
||||
.name = "qt1050",
|
||||
.of_match_table = of_match_ptr(qt1050_of_match),
|
||||
.pm = &qt1050_pm_ops,
|
||||
},
|
||||
.probe_new = qt1050_probe,
|
||||
};
|
||||
|
||||
module_i2c_driver(qt1050_driver);
|
||||
|
||||
MODULE_AUTHOR("Marco Felsch <kernel@pengutronix.de");
|
||||
MODULE_DESCRIPTION("Driver for AT42QT1050 QTouch sensor");
|
||||
MODULE_LICENSE("GPL v2");
|
||||
|
|
@ -15,6 +15,7 @@
|
|||
#include <linux/of.h>
|
||||
#include <linux/of_address.h>
|
||||
#include <linux/platform_device.h>
|
||||
#include <linux/pm_wakeirq.h>
|
||||
#include <linux/mfd/syscon.h>
|
||||
#include <linux/regmap.h>
|
||||
|
||||
|
|
@ -167,28 +168,9 @@ static int imx_snvs_pwrkey_probe(struct platform_device *pdev)
|
|||
}
|
||||
|
||||
device_init_wakeup(&pdev->dev, pdata->wakeup);
|
||||
|
||||
return 0;
|
||||
}
|
||||
|
||||
static int __maybe_unused imx_snvs_pwrkey_suspend(struct device *dev)
|
||||
{
|
||||
struct platform_device *pdev = to_platform_device(dev);
|
||||
struct pwrkey_drv_data *pdata = platform_get_drvdata(pdev);
|
||||
|
||||
if (device_may_wakeup(&pdev->dev))
|
||||
enable_irq_wake(pdata->irq);
|
||||
|
||||
return 0;
|
||||
}
|
||||
|
||||
static int __maybe_unused imx_snvs_pwrkey_resume(struct device *dev)
|
||||
{
|
||||
struct platform_device *pdev = to_platform_device(dev);
|
||||
struct pwrkey_drv_data *pdata = platform_get_drvdata(pdev);
|
||||
|
||||
if (device_may_wakeup(&pdev->dev))
|
||||
disable_irq_wake(pdata->irq);
|
||||
error = dev_pm_set_wake_irq(&pdev->dev, pdata->irq);
|
||||
if (error)
|
||||
dev_err(&pdev->dev, "irq wake enable failed.\n");
|
||||
|
||||
return 0;
|
||||
}
|
||||
|
|
@ -199,13 +181,9 @@ static const struct of_device_id imx_snvs_pwrkey_ids[] = {
|
|||
};
|
||||
MODULE_DEVICE_TABLE(of, imx_snvs_pwrkey_ids);
|
||||
|
||||
static SIMPLE_DEV_PM_OPS(imx_snvs_pwrkey_pm_ops, imx_snvs_pwrkey_suspend,
|
||||
imx_snvs_pwrkey_resume);
|
||||
|
||||
static struct platform_driver imx_snvs_pwrkey_driver = {
|
||||
.driver = {
|
||||
.name = "snvs_pwrkey",
|
||||
.pm = &imx_snvs_pwrkey_pm_ops,
|
||||
.of_match_table = imx_snvs_pwrkey_ids,
|
||||
},
|
||||
.probe = imx_snvs_pwrkey_probe,
|
||||
|
|
|
|||
|
|
@ -46,6 +46,7 @@
|
|||
#define CONTINUE_TIME_SEL(x) ((x) << 16) /* 4 bits */
|
||||
#define KEY_MODE_SEL(x) ((x) << 12) /* 2 bits */
|
||||
#define LEVELA_B_CNT(x) ((x) << 8) /* 4 bits */
|
||||
#define HOLD_KEY_EN(x) ((x) << 7)
|
||||
#define HOLD_EN(x) ((x) << 6)
|
||||
#define LEVELB_VOL(x) ((x) << 4) /* 2 bits */
|
||||
#define SAMPLE_RATE(x) ((x) << 2) /* 2 bits */
|
||||
|
|
@ -63,6 +64,25 @@
|
|||
#define CHAN0_KEYDOWN_IRQ BIT(1)
|
||||
#define CHAN0_DATA_IRQ BIT(0)
|
||||
|
||||
/* struct lradc_variant - Describe sun4i-a10-lradc-keys hardware variant
|
||||
* @divisor_numerator: The numerator of lradc Vref internally divisor
|
||||
* @divisor_denominator: The denominator of lradc Vref internally divisor
|
||||
*/
|
||||
struct lradc_variant {
|
||||
u8 divisor_numerator;
|
||||
u8 divisor_denominator;
|
||||
};
|
||||
|
||||
static const struct lradc_variant lradc_variant_a10 = {
|
||||
.divisor_numerator = 2,
|
||||
.divisor_denominator = 3
|
||||
};
|
||||
|
||||
static const struct lradc_variant r_lradc_variant_a83t = {
|
||||
.divisor_numerator = 3,
|
||||
.divisor_denominator = 4
|
||||
};
|
||||
|
||||
struct sun4i_lradc_keymap {
|
||||
u32 voltage;
|
||||
u32 keycode;
|
||||
|
|
@ -74,6 +94,7 @@ struct sun4i_lradc_data {
|
|||
void __iomem *base;
|
||||
struct regulator *vref_supply;
|
||||
struct sun4i_lradc_keymap *chan0_map;
|
||||
const struct lradc_variant *variant;
|
||||
u32 chan0_map_count;
|
||||
u32 chan0_keycode;
|
||||
u32 vref;
|
||||
|
|
@ -128,9 +149,9 @@ static int sun4i_lradc_open(struct input_dev *dev)
|
|||
if (error)
|
||||
return error;
|
||||
|
||||
/* lradc Vref internally is divided by 2/3 */
|
||||
lradc->vref = regulator_get_voltage(lradc->vref_supply) * 2 / 3;
|
||||
|
||||
lradc->vref = regulator_get_voltage(lradc->vref_supply) *
|
||||
lradc->variant->divisor_numerator /
|
||||
lradc->variant->divisor_denominator;
|
||||
/*
|
||||
* Set sample time to 4 ms / 250 Hz. Wait 2 * 4 ms for key to
|
||||
* stabilize on press, wait (1 + 1) * 4 ms for key release
|
||||
|
|
@ -222,6 +243,12 @@ static int sun4i_lradc_probe(struct platform_device *pdev)
|
|||
if (error)
|
||||
return error;
|
||||
|
||||
lradc->variant = of_device_get_match_data(&pdev->dev);
|
||||
if (!lradc->variant) {
|
||||
dev_err(&pdev->dev, "Missing sun4i-a10-lradc-keys variant\n");
|
||||
return -EINVAL;
|
||||
}
|
||||
|
||||
lradc->vref_supply = devm_regulator_get(dev, "vref");
|
||||
if (IS_ERR(lradc->vref_supply))
|
||||
return PTR_ERR(lradc->vref_supply);
|
||||
|
|
@ -265,7 +292,10 @@ static int sun4i_lradc_probe(struct platform_device *pdev)
|
|||
}
|
||||
|
||||
static const struct of_device_id sun4i_lradc_of_match[] = {
|
||||
{ .compatible = "allwinner,sun4i-a10-lradc-keys", },
|
||||
{ .compatible = "allwinner,sun4i-a10-lradc-keys",
|
||||
.data = &lradc_variant_a10 },
|
||||
{ .compatible = "allwinner,sun8i-a83t-r-lradc",
|
||||
.data = &r_lradc_variant_a83t },
|
||||
{ /* sentinel */ }
|
||||
};
|
||||
MODULE_DEVICE_TABLE(of, sun4i_lradc_of_match);
|
||||
|
|
|
|||
|
|
@ -290,6 +290,18 @@ config INPUT_GPIO_DECODER
|
|||
To compile this driver as a module, choose M here: the module
|
||||
will be called gpio_decoder.
|
||||
|
||||
config INPUT_GPIO_VIBRA
|
||||
tristate "GPIO vibrator support"
|
||||
depends on GPIOLIB || COMPILE_TEST
|
||||
select INPUT_FF_MEMLESS
|
||||
help
|
||||
Say Y here to get support for GPIO based vibrator devices.
|
||||
|
||||
If unsure, say N.
|
||||
|
||||
To compile this driver as a module, choose M here: the module will be
|
||||
called gpio-vibra.
|
||||
|
||||
config INPUT_IXP4XX_BEEPER
|
||||
tristate "IXP4XX Beeper support"
|
||||
depends on ARCH_IXP4XX
|
||||
|
|
|
|||
|
|
@ -36,6 +36,7 @@ obj-$(CONFIG_INPUT_DRV2667_HAPTICS) += drv2667.o
|
|||
obj-$(CONFIG_INPUT_GP2A) += gp2ap002a00f.o
|
||||
obj-$(CONFIG_INPUT_GPIO_BEEPER) += gpio-beeper.o
|
||||
obj-$(CONFIG_INPUT_GPIO_DECODER) += gpio_decoder.o
|
||||
obj-$(CONFIG_INPUT_GPIO_VIBRA) += gpio-vibra.o
|
||||
obj-$(CONFIG_INPUT_HISI_POWERKEY) += hisi_powerkey.o
|
||||
obj-$(CONFIG_HP_SDC_RTC) += hp_sdc_rtc.o
|
||||
obj-$(CONFIG_INPUT_IMS_PCU) += ims-pcu.o
|
||||
|
|
|
|||
|
|
@ -0,0 +1,207 @@
|
|||
// SPDX-License-Identifier: GPL-2.0+
|
||||
/*
|
||||
* GPIO vibrator driver
|
||||
*
|
||||
* Copyright (C) 2019 Luca Weiss <luca@z3ntu.xyz>
|
||||
*
|
||||
* Based on PWM vibrator driver:
|
||||
* Copyright (C) 2017 Collabora Ltd.
|
||||
*
|
||||
* Based on previous work from:
|
||||
* Copyright (C) 2012 Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
||||
*
|
||||
* Based on PWM beeper driver:
|
||||
* Copyright (C) 2010, Lars-Peter Clausen <lars@metafoo.de>
|
||||
*/
|
||||
|
||||
#include <linux/gpio/consumer.h>
|
||||
#include <linux/input.h>
|
||||
#include <linux/kernel.h>
|
||||
#include <linux/module.h>
|
||||
#include <linux/of_device.h>
|
||||
#include <linux/platform_device.h>
|
||||
#include <linux/property.h>
|
||||
#include <linux/regulator/consumer.h>
|
||||
#include <linux/slab.h>
|
||||
|
||||
struct gpio_vibrator {
|
||||
struct input_dev *input;
|
||||
struct gpio_desc *gpio;
|
||||
struct regulator *vcc;
|
||||
|
||||
struct work_struct play_work;
|
||||
bool running;
|
||||
bool vcc_on;
|
||||
};
|
||||
|
||||
static int gpio_vibrator_start(struct gpio_vibrator *vibrator)
|
||||
{
|
||||
struct device *pdev = vibrator->input->dev.parent;
|
||||
int err;
|
||||
|
||||
if (!vibrator->vcc_on) {
|
||||
err = regulator_enable(vibrator->vcc);
|
||||
if (err) {
|
||||
dev_err(pdev, "failed to enable regulator: %d\n", err);
|
||||
return err;
|
||||
}
|
||||
vibrator->vcc_on = true;
|
||||
}
|
||||
|
||||
gpiod_set_value_cansleep(vibrator->gpio, 1);
|
||||
|
||||
return 0;
|
||||
}
|
||||
|
||||
static void gpio_vibrator_stop(struct gpio_vibrator *vibrator)
|
||||
{
|
||||
gpiod_set_value_cansleep(vibrator->gpio, 0);
|
||||
|
||||
if (vibrator->vcc_on) {
|
||||
regulator_disable(vibrator->vcc);
|
||||
vibrator->vcc_on = false;
|
||||
}
|
||||
}
|
||||
|
||||
static void gpio_vibrator_play_work(struct work_struct *work)
|
||||
{
|
||||
struct gpio_vibrator *vibrator =
|
||||
container_of(work, struct gpio_vibrator, play_work);
|
||||
|
||||
if (vibrator->running)
|
||||
gpio_vibrator_start(vibrator);
|
||||
else
|
||||
gpio_vibrator_stop(vibrator);
|
||||
}
|
||||
|
||||
static int gpio_vibrator_play_effect(struct input_dev *dev, void *data,
|
||||
struct ff_effect *effect)
|
||||
{
|
||||
struct gpio_vibrator *vibrator = input_get_drvdata(dev);
|
||||
int level;
|
||||
|
||||
level = effect->u.rumble.strong_magnitude;
|
||||
if (!level)
|
||||
level = effect->u.rumble.weak_magnitude;
|
||||
|
||||
vibrator->running = level;
|
||||
schedule_work(&vibrator->play_work);
|
||||
|
||||
return 0;
|
||||
}
|
||||
|
||||
static void gpio_vibrator_close(struct input_dev *input)
|
||||
{
|
||||
struct gpio_vibrator *vibrator = input_get_drvdata(input);
|
||||
|
||||
cancel_work_sync(&vibrator->play_work);
|
||||
gpio_vibrator_stop(vibrator);
|
||||
vibrator->running = false;
|
||||
}
|
||||
|
||||
static int gpio_vibrator_probe(struct platform_device *pdev)
|
||||
{
|
||||
struct gpio_vibrator *vibrator;
|
||||
int err;
|
||||
|
||||
vibrator = devm_kzalloc(&pdev->dev, sizeof(*vibrator), GFP_KERNEL);
|
||||
if (!vibrator)
|
||||
return -ENOMEM;
|
||||
|
||||
vibrator->input = devm_input_allocate_device(&pdev->dev);
|
||||
if (!vibrator->input)
|
||||
return -ENOMEM;
|
||||
|
||||
vibrator->vcc = devm_regulator_get(&pdev->dev, "vcc");
|
||||
err = PTR_ERR_OR_ZERO(vibrator->vcc);
|
||||
if (err) {
|
||||
if (err != -EPROBE_DEFER)
|
||||
dev_err(&pdev->dev, "Failed to request regulator: %d\n",
|
||||
err);
|
||||
return err;
|
||||
}
|
||||
|
||||
vibrator->gpio = devm_gpiod_get(&pdev->dev, "enable", GPIOD_OUT_LOW);
|
||||
err = PTR_ERR_OR_ZERO(vibrator->gpio);
|
||||
if (err) {
|
||||
if (err != -EPROBE_DEFER)
|
||||
dev_err(&pdev->dev, "Failed to request main gpio: %d\n",
|
||||
err);
|
||||
return err;
|
||||
}
|
||||
|
||||
INIT_WORK(&vibrator->play_work, gpio_vibrator_play_work);
|
||||
|
||||
vibrator->input->name = "gpio-vibrator";
|
||||
vibrator->input->id.bustype = BUS_HOST;
|
||||
vibrator->input->close = gpio_vibrator_close;
|
||||
|
||||
input_set_drvdata(vibrator->input, vibrator);
|
||||
input_set_capability(vibrator->input, EV_FF, FF_RUMBLE);
|
||||
|
||||
err = input_ff_create_memless(vibrator->input, NULL,
|
||||
gpio_vibrator_play_effect);
|
||||
if (err) {
|
||||
dev_err(&pdev->dev, "Couldn't create FF dev: %d\n", err);
|
||||
return err;
|
||||
}
|
||||
|
||||
err = input_register_device(vibrator->input);
|
||||
if (err) {
|
||||
dev_err(&pdev->dev, "Couldn't register input dev: %d\n", err);
|
||||
return err;
|
||||
}
|
||||
|
||||
platform_set_drvdata(pdev, vibrator);
|
||||
|
||||
return 0;
|
||||
}
|
||||
|
||||
static int __maybe_unused gpio_vibrator_suspend(struct device *dev)
|
||||
{
|
||||
struct platform_device *pdev = to_platform_device(dev);
|
||||
struct gpio_vibrator *vibrator = platform_get_drvdata(pdev);
|
||||
|
||||
cancel_work_sync(&vibrator->play_work);
|
||||
if (vibrator->running)
|
||||
gpio_vibrator_stop(vibrator);
|
||||
|
||||
return 0;
|
||||
}
|
||||
|
||||
static int __maybe_unused gpio_vibrator_resume(struct device *dev)
|
||||
{
|
||||
struct platform_device *pdev = to_platform_device(dev);
|
||||
struct gpio_vibrator *vibrator = platform_get_drvdata(pdev);
|
||||
|
||||
if (vibrator->running)
|
||||
gpio_vibrator_start(vibrator);
|
||||
|
||||
return 0;
|
||||
}
|
||||
|
||||
static SIMPLE_DEV_PM_OPS(gpio_vibrator_pm_ops,
|
||||
gpio_vibrator_suspend, gpio_vibrator_resume);
|
||||
|
||||
#ifdef CONFIG_OF
|
||||
static const struct of_device_id gpio_vibra_dt_match_table[] = {
|
||||
{ .compatible = "gpio-vibrator" },
|
||||
{}
|
||||
};
|
||||
MODULE_DEVICE_TABLE(of, gpio_vibra_dt_match_table);
|
||||
#endif
|
||||
|
||||
static struct platform_driver gpio_vibrator_driver = {
|
||||
.probe = gpio_vibrator_probe,
|
||||
.driver = {
|
||||
.name = "gpio-vibrator",
|
||||
.pm = &gpio_vibrator_pm_ops,
|
||||
.of_match_table = of_match_ptr(gpio_vibra_dt_match_table),
|
||||
},
|
||||
};
|
||||
module_platform_driver(gpio_vibrator_driver);
|
||||
|
||||
MODULE_AUTHOR("Luca Weiss <luca@z3ntu.xy>");
|
||||
MODULE_DESCRIPTION("GPIO vibrator driver");
|
||||
MODULE_LICENSE("GPL");
|
||||
MODULE_ALIAS("platform:gpio-vibrator");
|
||||
|
|
@ -373,6 +373,8 @@ static irqreturn_t psmouse_interrupt(struct serio *serio,
|
|||
if (ps2_handle_response(&psmouse->ps2dev, data))
|
||||
goto out;
|
||||
|
||||
pm_wakeup_event(&serio->dev, 0);
|
||||
|
||||
if (psmouse->state <= PSMOUSE_RESYNCING)
|
||||
goto out;
|
||||
|
||||
|
|
|
|||
|
|
@ -456,25 +456,15 @@ static int rmi_f54_vidioc_fmt(struct file *file, void *priv,
|
|||
static int rmi_f54_vidioc_enum_fmt(struct file *file, void *priv,
|
||||
struct v4l2_fmtdesc *fmt)
|
||||
{
|
||||
struct f54_data *f54 = video_drvdata(file);
|
||||
|
||||
if (fmt->type != V4L2_BUF_TYPE_VIDEO_CAPTURE)
|
||||
return -EINVAL;
|
||||
|
||||
switch (fmt->index) {
|
||||
case 0:
|
||||
fmt->pixelformat = V4L2_TCH_FMT_DELTA_TD16;
|
||||
break;
|
||||
|
||||
case 1:
|
||||
fmt->pixelformat = V4L2_TCH_FMT_DELTA_TD08;
|
||||
break;
|
||||
|
||||
case 2:
|
||||
fmt->pixelformat = V4L2_TCH_FMT_TU16;
|
||||
break;
|
||||
|
||||
default:
|
||||
if (fmt->index)
|
||||
return -EINVAL;
|
||||
}
|
||||
|
||||
fmt->pixelformat = f54->format.pixelformat;
|
||||
|
||||
return 0;
|
||||
}
|
||||
|
|
@ -692,6 +682,7 @@ static int rmi_f54_probe(struct rmi_function *fn)
|
|||
return -ENOMEM;
|
||||
|
||||
rmi_f54_create_input_map(f54);
|
||||
rmi_f54_set_input(f54, 0);
|
||||
|
||||
/* register video device */
|
||||
strlcpy(f54->v4l2.name, F54_NAME, sizeof(f54->v4l2.name));
|
||||
|
|
|
|||
|
|
@ -254,6 +254,7 @@ config SERIO_APBPS2
|
|||
|
||||
config SERIO_OLPC_APSP
|
||||
tristate "OLPC AP-SP input support"
|
||||
depends on ARCH_MMP || COMPILE_TEST
|
||||
help
|
||||
Say Y here if you want support for the keyboard and touchpad included
|
||||
in the OLPC XO-1.75 and XO-4 laptops.
|
||||
|
|
|
|||
|
|
@ -440,5 +440,7 @@ static void __exit hv_kbd_exit(void)
|
|||
}
|
||||
|
||||
MODULE_LICENSE("GPL");
|
||||
MODULE_DESCRIPTION("Microsoft Hyper-V Synthetic Keyboard Driver");
|
||||
|
||||
module_init(hv_kbd_init);
|
||||
module_exit(hv_kbd_exit);
|
||||
|
|
|
|||
|
|
@ -573,9 +573,6 @@ static irqreturn_t i8042_interrupt(int irq, void *dev_id)
|
|||
port = &i8042_ports[port_no];
|
||||
serio = port->exists ? port->serio : NULL;
|
||||
|
||||
if (irq && serio)
|
||||
pm_wakeup_event(&serio->dev, 0);
|
||||
|
||||
filter_dbg(port->driver_bound, data, "<- i8042 (interrupt, %d, %d%s%s)\n",
|
||||
port_no, irq,
|
||||
dfl & SERIO_PARITY ? ", bad parity" : "",
|
||||
|
|
|
|||
|
|
@ -409,6 +409,7 @@ bool ps2_handle_ack(struct ps2dev *ps2dev, u8 data)
|
|||
ps2dev->nak = PS2_RET_ERR;
|
||||
break;
|
||||
}
|
||||
/* Fall through */
|
||||
|
||||
/*
|
||||
* Workaround for mice which don't ACK the Get ID command.
|
||||
|
|
|
|||
|
|
@ -1312,4 +1312,14 @@ config TOUCHSCREEN_ROHM_BU21023
|
|||
To compile this driver as a module, choose M here: the
|
||||
module will be called bu21023_ts.
|
||||
|
||||
config TOUCHSCREEN_IQS5XX
|
||||
tristate "Azoteq IQS550/572/525 trackpad/touchscreen controller"
|
||||
depends on I2C
|
||||
help
|
||||
Say Y to enable support for the Azoteq IQS550/572/525
|
||||
family of trackpad/touchscreen controllers.
|
||||
|
||||
To compile this driver as a module, choose M here: the
|
||||
module will be called iqs5xx.
|
||||
|
||||
endif
|
||||
|
|
|
|||
|
|
@ -110,3 +110,4 @@ obj-$(CONFIG_TOUCHSCREEN_ZFORCE) += zforce_ts.o
|
|||
obj-$(CONFIG_TOUCHSCREEN_COLIBRI_VF50) += colibri-vf50-ts.o
|
||||
obj-$(CONFIG_TOUCHSCREEN_ROHM_BU21023) += rohm_bu21023.o
|
||||
obj-$(CONFIG_TOUCHSCREEN_RASPBERRYPI_FW) += raspberrypi-ts.o
|
||||
obj-$(CONFIG_TOUCHSCREEN_IQS5XX) += iqs5xx.o
|
||||
|
|
|
|||
|
|
@ -1,20 +1,8 @@
|
|||
// SPDX-License-Identifier: GPL-2.0
|
||||
/*
|
||||
* Copyright (C) 2012 Simon Budig, <simon.budig@kernelconcepts.de>
|
||||
* Daniel Wagener <daniel.wagener@kernelconcepts.de> (M09 firmware support)
|
||||
* Lothar Waßmann <LW@KARO-electronics.de> (DT support)
|
||||
*
|
||||
* This software is licensed under the terms of the GNU General Public
|
||||
* License version 2, as published by the Free Software Foundation, and
|
||||
* may be copied, distributed, and modified under those terms.
|
||||
*
|
||||
* This program is distributed in the hope that it will be useful,
|
||||
* but WITHOUT ANY WARRANTY; without even the implied warranty of
|
||||
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
||||
* GNU General Public License for more details.
|
||||
*
|
||||
* You should have received a copy of the GNU General Public
|
||||
* License along with this library; if not, write to the Free Software
|
||||
* Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
|
||||
*/
|
||||
|
||||
/*
|
||||
|
|
@ -39,7 +27,6 @@
|
|||
#include <linux/gpio/consumer.h>
|
||||
#include <linux/input/mt.h>
|
||||
#include <linux/input/touchscreen.h>
|
||||
#include <linux/of_device.h>
|
||||
|
||||
#define WORK_REGISTER_THRESHOLD 0x00
|
||||
#define WORK_REGISTER_REPORT_RATE 0x08
|
||||
|
|
@ -1073,7 +1060,7 @@ static int edt_ft5x06_ts_probe(struct i2c_client *client,
|
|||
return -ENOMEM;
|
||||
}
|
||||
|
||||
chip_data = of_device_get_match_data(&client->dev);
|
||||
chip_data = device_get_match_data(&client->dev);
|
||||
if (!chip_data)
|
||||
chip_data = (const struct edt_i2c_chip_data *)id->driver_data;
|
||||
if (!chip_data || !chip_data->max_support_points) {
|
||||
|
|
@ -1254,7 +1241,6 @@ static const struct i2c_device_id edt_ft5x06_ts_id[] = {
|
|||
};
|
||||
MODULE_DEVICE_TABLE(i2c, edt_ft5x06_ts_id);
|
||||
|
||||
#ifdef CONFIG_OF
|
||||
static const struct of_device_id edt_ft5x06_of_match[] = {
|
||||
{ .compatible = "edt,edt-ft5206", .data = &edt_ft5x06_data },
|
||||
{ .compatible = "edt,edt-ft5306", .data = &edt_ft5x06_data },
|
||||
|
|
@ -1266,12 +1252,11 @@ static const struct of_device_id edt_ft5x06_of_match[] = {
|
|||
{ /* sentinel */ }
|
||||
};
|
||||
MODULE_DEVICE_TABLE(of, edt_ft5x06_of_match);
|
||||
#endif
|
||||
|
||||
static struct i2c_driver edt_ft5x06_ts_driver = {
|
||||
.driver = {
|
||||
.name = "edt_ft5x06",
|
||||
.of_match_table = of_match_ptr(edt_ft5x06_of_match),
|
||||
.of_match_table = edt_ft5x06_of_match,
|
||||
.pm = &edt_ft5x06_ts_pm_ops,
|
||||
},
|
||||
.id_table = edt_ft5x06_ts_id,
|
||||
|
|
@ -1283,4 +1268,4 @@ module_i2c_driver(edt_ft5x06_ts_driver);
|
|||
|
||||
MODULE_AUTHOR("Simon Budig <simon.budig@kernelconcepts.de>");
|
||||
MODULE_DESCRIPTION("EDT FT5x06 I2C Touchscreen Driver");
|
||||
MODULE_LICENSE("GPL");
|
||||
MODULE_LICENSE("GPL v2");
|
||||
|
|
|
|||
|
|
@ -27,6 +27,7 @@
|
|||
#include <linux/delay.h>
|
||||
#include <linux/irq.h>
|
||||
#include <linux/interrupt.h>
|
||||
#include <linux/regulator/consumer.h>
|
||||
#include <linux/slab.h>
|
||||
#include <linux/acpi.h>
|
||||
#include <linux/of.h>
|
||||
|
|
@ -47,6 +48,8 @@ struct goodix_ts_data {
|
|||
struct touchscreen_properties prop;
|
||||
unsigned int max_touch_num;
|
||||
unsigned int int_trigger_type;
|
||||
struct regulator *avdd28;
|
||||
struct regulator *vddio;
|
||||
struct gpio_desc *gpiod_int;
|
||||
struct gpio_desc *gpiod_rst;
|
||||
u16 id;
|
||||
|
|
@ -216,6 +219,7 @@ static const struct goodix_chip_data *goodix_get_chip_data(u16 id)
|
|||
{
|
||||
switch (id) {
|
||||
case 1151:
|
||||
case 5663:
|
||||
case 5688:
|
||||
return >1x_chip_data;
|
||||
|
||||
|
|
@ -532,6 +536,24 @@ static int goodix_get_gpio_config(struct goodix_ts_data *ts)
|
|||
return -EINVAL;
|
||||
dev = &ts->client->dev;
|
||||
|
||||
ts->avdd28 = devm_regulator_get(dev, "AVDD28");
|
||||
if (IS_ERR(ts->avdd28)) {
|
||||
error = PTR_ERR(ts->avdd28);
|
||||
if (error != -EPROBE_DEFER)
|
||||
dev_err(dev,
|
||||
"Failed to get AVDD28 regulator: %d\n", error);
|
||||
return error;
|
||||
}
|
||||
|
||||
ts->vddio = devm_regulator_get(dev, "VDDIO");
|
||||
if (IS_ERR(ts->vddio)) {
|
||||
error = PTR_ERR(ts->vddio);
|
||||
if (error != -EPROBE_DEFER)
|
||||
dev_err(dev,
|
||||
"Failed to get VDDIO regulator: %d\n", error);
|
||||
return error;
|
||||
}
|
||||
|
||||
/* Get the interrupt GPIO pin number */
|
||||
gpiod = devm_gpiod_get_optional(dev, GOODIX_GPIO_INT_NAME, GPIOD_IN);
|
||||
if (IS_ERR(gpiod)) {
|
||||
|
|
@ -764,6 +786,14 @@ err_release_cfg:
|
|||
complete_all(&ts->firmware_loading_complete);
|
||||
}
|
||||
|
||||
static void goodix_disable_regulators(void *arg)
|
||||
{
|
||||
struct goodix_ts_data *ts = arg;
|
||||
|
||||
regulator_disable(ts->vddio);
|
||||
regulator_disable(ts->avdd28);
|
||||
}
|
||||
|
||||
static int goodix_ts_probe(struct i2c_client *client,
|
||||
const struct i2c_device_id *id)
|
||||
{
|
||||
|
|
@ -789,6 +819,29 @@ static int goodix_ts_probe(struct i2c_client *client,
|
|||
if (error)
|
||||
return error;
|
||||
|
||||
/* power up the controller */
|
||||
error = regulator_enable(ts->avdd28);
|
||||
if (error) {
|
||||
dev_err(&client->dev,
|
||||
"Failed to enable AVDD28 regulator: %d\n",
|
||||
error);
|
||||
return error;
|
||||
}
|
||||
|
||||
error = regulator_enable(ts->vddio);
|
||||
if (error) {
|
||||
dev_err(&client->dev,
|
||||
"Failed to enable VDDIO regulator: %d\n",
|
||||
error);
|
||||
regulator_disable(ts->avdd28);
|
||||
return error;
|
||||
}
|
||||
|
||||
error = devm_add_action_or_reset(&client->dev,
|
||||
goodix_disable_regulators, ts);
|
||||
if (error)
|
||||
return error;
|
||||
|
||||
if (ts->gpiod_int && ts->gpiod_rst) {
|
||||
/* reset the controller */
|
||||
error = goodix_reset(ts);
|
||||
|
|
@ -945,6 +998,7 @@ MODULE_DEVICE_TABLE(acpi, goodix_acpi_match);
|
|||
#ifdef CONFIG_OF
|
||||
static const struct of_device_id goodix_of_match[] = {
|
||||
{ .compatible = "goodix,gt1151" },
|
||||
{ .compatible = "goodix,gt5663" },
|
||||
{ .compatible = "goodix,gt5688" },
|
||||
{ .compatible = "goodix,gt911" },
|
||||
{ .compatible = "goodix,gt9110" },
|
||||
|
|
|
|||
File diff suppressed because it is too large
Load Diff
|
|
@ -606,6 +606,7 @@
|
|||
#define KEY_SCREENSAVER 0x245 /* AL Screen Saver */
|
||||
#define KEY_VOICECOMMAND 0x246 /* Listening Voice Command */
|
||||
#define KEY_ASSISTANT 0x247 /* AL Context-aware desktop assistant */
|
||||
#define KEY_KBD_LAYOUT_NEXT 0x248 /* AC Next Keyboard Layout Select */
|
||||
|
||||
#define KEY_BRIGHTNESS_MIN 0x250 /* Set Brightness to Minimum */
|
||||
#define KEY_BRIGHTNESS_MAX 0x251 /* Set Brightness to Maximum */
|
||||
|
|
|
|||
Loading…
Reference in New Issue