From 137cd7100ec6fa36d610e106df00acb4d8af99df Mon Sep 17 00:00:00 2001
From: Linus Walleij <linus.walleij@linaro.org>
Date: Thu, 11 Oct 2018 20:06:23 +0200
Subject: [PATCH] ARM: dts: Enable Gemini flash access

Some Gemini platforms have a parallel NOR flash which conflicts
with use cases reusing some of the flash lines (such as CE1)
for GPIO.

Fix this on the D-Link DIR-685 and Itian SQ201 by creating
"enabled" and "disabled" states for the flash pin control
handle, and rely on the flash handling code to switch this
in and out when accessed so these lines can be used
for GPIO when flash is not accessed, and enable flash
access.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
---
 arch/arm/boot/dts/gemini-dlink-dir-685.dts | 35 +++++++++++++++-------
 arch/arm/boot/dts/gemini-sq201.dts         | 31 ++++++++++---------
 2 files changed, 41 insertions(+), 25 deletions(-)

diff --git a/arch/arm/boot/dts/gemini-dlink-dir-685.dts b/arch/arm/boot/dts/gemini-dlink-dir-685.dts
index 502a361d1fe9..318e9b2ba7dc 100644
--- a/arch/arm/boot/dts/gemini-dlink-dir-685.dts
+++ b/arch/arm/boot/dts/gemini-dlink-dir-685.dts
@@ -64,7 +64,6 @@
 		gpio-sck = <&gpio1 5 GPIO_ACTIVE_HIGH>;
 		gpio-miso = <&gpio1 8 GPIO_ACTIVE_HIGH>;
 		gpio-mosi = <&gpio1 7 GPIO_ACTIVE_HIGH>;
-		/* Collides with pflash CE1, not so cool */
 		cs-gpios = <&gpio0 20 GPIO_ACTIVE_HIGH>;
 		num-chipselects = <1>;
 
@@ -253,15 +252,18 @@
 	soc {
 		flash@30000000 {
 			/*
-			 * Flash access is by default disabled, because it
-			 * collides with the Chip Enable signal for the display
-			 * panel, that reuse the parallel flash Chip Select 1
-			 * (CS1). Enabling flash makes graphics stop working.
-			 *
-			 * We might be able to hack around this by letting
-			 * GPIO poke around in the flash controller registers.
+			 * Flash access collides with the Chip Enable signal for
+			 * the display panel, that reuse the parallel flash Chip
+			 * Select 1 (CS1). We switch the pin control state so we
+			 * enable these pins for flash access only when we need
+			 * then, and when disabled they can be used for GPIO which
+			 * is what the display panel needs.
 			 */
-			/* status = "okay"; */
+			status = "okay";
+			pinctrl-names = "enabled", "disabled";
+			pinctrl-0 = <&pflash_default_pins>;
+			pinctrl-1 = <&pflash_disabled_pins>;
+
 			/* 32MB of flash */
 			reg = <0x30000000 0x02000000>;
 
@@ -327,7 +329,6 @@
 						"gpio0cgrp",
 						"gpio0egrp",
 						"gpio0fgrp",
-						"gpio0ggrp",
 						"gpio0hgrp";
 					};
 				};
@@ -342,6 +343,18 @@
 						groups = "gpio1bgrp";
 					};
 				};
+				/*
+				 * These GPIO groups will be mapped in over some
+				 * of the flash pins when the flash is not in
+				 * active use.
+				 */
+				pflash_disabled_pins: pinctrl-pflash-disabled {
+					mux {
+						function = "gpio0";
+						groups = "gpio0ggrp", "gpio0igrp", "gpio0jgrp",
+							 "gpio0kgrp";
+					};
+				};
 				pinctrl-gmii {
 					mux {
 						function = "gmii";
@@ -430,7 +443,7 @@
 		};
 
 		display-controller@6a000000 {
-			status = "okay";
+			status = "disabled";
 
 			port@0 {
 				reg = <0>;
diff --git a/arch/arm/boot/dts/gemini-sq201.dts b/arch/arm/boot/dts/gemini-sq201.dts
index 3787cf3763c4..af4be6ecb02c 100644
--- a/arch/arm/boot/dts/gemini-sq201.dts
+++ b/arch/arm/boot/dts/gemini-sq201.dts
@@ -41,14 +41,12 @@
 		compatible = "gpio-leds";
 		led-green-info {
 			label = "sq201:green:info";
-			/* Conflict with parallel flash */
 			gpios = <&gpio0 20 GPIO_ACTIVE_HIGH>;
 			default-state = "on";
 			linux,default-trigger = "heartbeat";
 		};
 		led-green-usb {
 			label = "sq201:green:usb";
-			/* Conflict with parallel and NAND flash */
 			gpios = <&gpio0 31 GPIO_ACTIVE_HIGH>;
 			default-state = "off";
 			linux,default-trigger = "usb-host";
@@ -126,15 +124,10 @@
 
 	soc {
 		flash@30000000 {
-			/*
-			 * Flash access can be enabled, with the side effect
-			 * of disabling access to GPIO LED on GPIO0[20] which
-			 * reuse one of the parallel flash chip select lines.
-			 * Also the default firmware on the machine has the
-			 * problem that since it uses the flash, the two LEDS
-			 * on the right become numb.
-			 */
-			/* status = "okay"; */
+			status = "okay";
+			pinctrl-names = "enabled", "disabled";
+			pinctrl-0 = <&pflash_default_pins>;
+			pinctrl-1 = <&pflash_disabled_pins>;
 			/* 16MB of flash */
 			reg = <0x30000000 0x01000000>;
 
@@ -184,9 +177,7 @@
 					mux {
 						function = "gpio0";
 						groups = "gpio0fgrp",
-						"gpio0ggrp",
-						"gpio0hgrp",
-						"gpio0kgrp";
+						"gpio0hgrp";
 					};
 				};
 				/*
@@ -199,6 +190,18 @@
 						groups = "gpio1dgrp";
 					};
 				};
+				/*
+				 * These GPIO groups will be mapped in over some
+				 * of the flash pins when the flash is not in
+				 * active use.
+				 */
+				pflash_disabled_pins: pinctrl-pflash-disabled {
+					mux {
+						function = "gpio0";
+						groups = "gpio0ggrp", "gpio0igrp", "gpio0jgrp",
+							 "gpio0kgrp";
+					};
+				};
 				pinctrl-gmii {
 					mux {
 						function = "gmii";