dt-bindings: power: supply: bq24257: Convert to DT schema format
Convert the binding to DT schema format. Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com> Reviewed-by: Rob Herring <robh@kernel.org>
This commit is contained in:
Sebastian Reichel
Sebastian Reichel
parent
648d383253
commit
102d4a0b69
|
|
@ -1,62 +0,0 @@
|
|||
Binding for TI bq24250/bq24251/bq24257 Li-Ion Charger
|
||||
|
||||
Required properties:
|
||||
- compatible: Should contain one of the following:
|
||||
* "ti,bq24250"
|
||||
* "ti,bq24251"
|
||||
* "ti,bq24257"
|
||||
- reg: integer, i2c address of the device.
|
||||
- interrupts: Interrupt mapping for GPIO IRQ (configure for both edges). Use in
|
||||
conjunction with "interrupt-parent".
|
||||
- ti,battery-regulation-voltage: integer, maximum charging voltage in uV.
|
||||
- ti,charge-current: integer, maximum charging current in uA.
|
||||
- ti,termination-current: integer, charge will be terminated when current in
|
||||
constant-voltage phase drops below this value (in uA).
|
||||
|
||||
Optional properties:
|
||||
- pg-gpios: GPIO used for connecting the bq2425x device PG (Power Good) pin.
|
||||
This pin is not available on all devices however it should be used if
|
||||
possible as this is the recommended way to obtain the charger's input PG
|
||||
state. If this pin is not specified a software-based approach for PG
|
||||
detection is used.
|
||||
- ti,current-limit: The maximum current to be drawn from the charger's input
|
||||
(in uA). If this property is not specified, the input limit current is
|
||||
set automatically using USB D+/D- signal based charger type detection.
|
||||
If the hardware does not support the D+/D- based detection, a default
|
||||
of 500,000 is used (=500mA) instead.
|
||||
- ti,ovp-voltage: Configures the over voltage protection voltage (in uV). If
|
||||
not specified a default of 6,5000,000 (=6.5V) is used.
|
||||
- ti,in-dpm-voltage: Configures the threshold input voltage for the dynamic
|
||||
power path management (in uV). If not specified a default of 4,360,000
|
||||
(=4.36V) is used.
|
||||
|
||||
Example:
|
||||
|
||||
bq24257 {
|
||||
compatible = "ti,bq24257";
|
||||
reg = <0x6a>;
|
||||
interrupt-parent = <&gpio1>;
|
||||
interrupts = <16 IRQ_TYPE_EDGE_BOTH>;
|
||||
|
||||
pg-gpios = <&gpio1 28 GPIO_ACTIVE_HIGH>;
|
||||
|
||||
ti,battery-regulation-voltage = <4200000>;
|
||||
ti,charge-current = <1000000>;
|
||||
ti,termination-current = <50000>;
|
||||
};
|
||||
|
||||
Example:
|
||||
|
||||
bq24250 {
|
||||
compatible = "ti,bq24250";
|
||||
reg = <0x6a>;
|
||||
interrupt-parent = <&gpio1>;
|
||||
interrupts = <16 IRQ_TYPE_EDGE_BOTH>;
|
||||
|
||||
ti,battery-regulation-voltage = <4200000>;
|
||||
ti,charge-current = <500000>;
|
||||
ti,termination-current = <50000>;
|
||||
ti,current-limit = <900000>;
|
||||
ti,ovp-voltage = <9500000>;
|
||||
ti,in-dpm-voltage = <4440000>;
|
||||
};
|
||||
|
|
@ -0,0 +1,124 @@
|
|||
# SPDX-License-Identifier: GPL-2.0
|
||||
# Copyright (C) 2021 Sebastian Reichel
|
||||
%YAML 1.2
|
||||
---
|
||||
$id: "http://devicetree.org/schemas/power/supply/bq24257.yaml#"
|
||||
$schema: "http://devicetree.org/meta-schemas/core.yaml#"
|
||||
|
||||
title: Binding for bq24250, bq24251 and bq24257 Li-Ion Charger
|
||||
|
||||
maintainers:
|
||||
- Sebastian Reichel <sre@kernel.org>
|
||||
|
||||
allOf:
|
||||
- $ref: power-supply.yaml#
|
||||
|
||||
properties:
|
||||
compatible:
|
||||
enum:
|
||||
- ti,bq24250
|
||||
- ti,bq24251
|
||||
- ti,bq24257
|
||||
|
||||
reg:
|
||||
maxItems: 1
|
||||
|
||||
interrupts:
|
||||
maxItems: 1
|
||||
|
||||
ti,battery-regulation-voltage:
|
||||
$ref: /schemas/types.yaml#/definitions/uint32
|
||||
description: maximum charging voltage in uV
|
||||
|
||||
ti,charge-current:
|
||||
$ref: /schemas/types.yaml#/definitions/uint32
|
||||
description: maximum charging current in uA
|
||||
|
||||
ti,termination-current:
|
||||
$ref: /schemas/types.yaml#/definitions/uint32
|
||||
description: |
|
||||
charge will be terminated when current in constant-voltage phase
|
||||
drops below this value (in uA)
|
||||
|
||||
pg-gpios:
|
||||
description: |
|
||||
GPIO used for connecting the bq2425x device PG (Power Good) pin.
|
||||
This pin is not available on all devices however it should be used if
|
||||
possible as this is the recommended way to obtain the charger's input PG
|
||||
state. If this pin is not specified a software-based approach for PG
|
||||
detection is used.
|
||||
maxItems: 1
|
||||
|
||||
ti,current-limit:
|
||||
$ref: /schemas/types.yaml#/definitions/uint32
|
||||
description: |
|
||||
The maximum current to be drawn from the charger's input (in uA).
|
||||
If this property is not specified, the input limit current is set
|
||||
automatically using USB D+/D- signal based charger type detection.
|
||||
If the hardware does not support the D+/D- based detection, a default
|
||||
of 500,000 is used (=500mA) instead.
|
||||
|
||||
ti,ovp-voltage:
|
||||
$ref: /schemas/types.yaml#/definitions/uint32
|
||||
description: |
|
||||
Configures the over voltage protection voltage (in uV).
|
||||
If not specified a default of 6,5000,000 (=6.5V) is used.
|
||||
|
||||
ti,in-dpm-voltage:
|
||||
$ref: /schemas/types.yaml#/definitions/uint32
|
||||
description: |
|
||||
Configures the threshold input voltage for the dynamic power path management (in uV).
|
||||
If not specified a default of 4,360,000 (=4.36V) is used.
|
||||
|
||||
required:
|
||||
- compatible
|
||||
- reg
|
||||
- interrupts
|
||||
- ti,battery-regulation-voltage
|
||||
- ti,charge-current
|
||||
- ti,termination-current
|
||||
|
||||
additionalProperties: false
|
||||
|
||||
examples:
|
||||
- |
|
||||
#include <dt-bindings/gpio/gpio.h>
|
||||
#include <dt-bindings/interrupt-controller/irq.h>
|
||||
i2c0 {
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
|
||||
charger@6a {
|
||||
compatible = "ti,bq24257";
|
||||
reg = <0x6a>;
|
||||
interrupt-parent = <&gpio1>;
|
||||
interrupts = <16 IRQ_TYPE_EDGE_BOTH>;
|
||||
|
||||
pg-gpios = <&gpio1 28 GPIO_ACTIVE_HIGH>;
|
||||
|
||||
ti,battery-regulation-voltage = <4200000>;
|
||||
ti,charge-current = <1000000>;
|
||||
ti,termination-current = <50000>;
|
||||
};
|
||||
};
|
||||
- |
|
||||
#include <dt-bindings/gpio/gpio.h>
|
||||
#include <dt-bindings/interrupt-controller/irq.h>
|
||||
i2c0 {
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
|
||||
charger@6a {
|
||||
compatible = "ti,bq24250";
|
||||
reg = <0x6a>;
|
||||
interrupt-parent = <&gpio1>;
|
||||
interrupts = <16 IRQ_TYPE_EDGE_BOTH>;
|
||||
|
||||
ti,battery-regulation-voltage = <4200000>;
|
||||
ti,charge-current = <500000>;
|
||||
ti,termination-current = <50000>;
|
||||
ti,current-limit = <900000>;
|
||||
ti,ovp-voltage = <9500000>;
|
||||
ti,in-dpm-voltage = <4440000>;
|
||||
};
|
||||
};
|
||||
Loading…
Reference in New Issue